INTRODUCTION TO FIELDPROGRAMMABLE GATE ARRAYS

(FPGAS)Bill Jason P. Tomas

Dept. of Electrical and Computer EngineeringUniversity of Nevada Las Vegas

FIELD PROGRAMMABLE ARRAYS

Dominant digital design implementation Ability to re-configure FPGA to implement any

digital logic function Partial re-configuration allows a portion of the FPGA

to be continuously running while another portion is being re-configured

FPGAs also contain analog circuitry features including a programmable slew rate and drive strength, differential comparators on I/O designed to be connected to differential signaling channels.

Mixed-signal FPGAs contains ADCs and DACs with analog signal conditional blocks allowing them to operate as a system-on-chip (SoC)

FPGA ARCHITECTURES

Early FPGAs N x N array of unit cells (CLB + routing)

Special routing along center axis

Next Generation FPGAs M x N unit cells Small block RAMs around edges

More recent FPGAs Added block RAM arrays Added multiplier cores Adders processor cores

FPGA ARCHITECTURE TRENDS

Memories Single & Dual-port RAMS FIFO (first-in first-out) ECC (error correcting codes)

Digital Signal Processors Multipliers Accumulators Arithmetic Logic Units (ALUs)

Embedded Processors Hardcore (dedicated processors)

Dedicated program and data memories Programmable RAM in FPGA can be used in conjunction with

the processor to provide program and data memories Soft core (synthesized from a HDL)

BASIC FPGA ARCHITECTURE

•More recent FPGA architectures have small block RAM arrays (usually placed in center column), multipliers, processor cores, DSP cores w/ multipliers, and I/O cells along columns for BGAs.

FPGA OPERATION

User writes configuration memory which defines the function of the system. This includes: the connectivity between the CLBs and the I/O cells, the logic to be implemented onto the CLBs, and the I/O blocks.

By changing the data in the configuration memory, the function of the system changes as well. This change in data can be implemented at anytime during FPGA operation (run-time configuration).

CONFIGURABLE LOGIC BLOCKS (CLBS) ARCHITECTURE CLBs consist of:

Look-up Tables (LUT) which implement the entries of a logic functions truth table Some FPGAs can use LUTs to implement small Random Access

Memory (RAM) Carry and Control Logic

Implements fast arithmetic operations (adders/ subtractors) Can be alsoconfigured for additional operations (Built-in-Self Test

iterative-OR chain) Memory Elements

Configurable Flip Flops (FFs)/ Latches( Programmable clock edges, set/reset, and clock enable)

These memory elements usually can be configured as shift-registers

CONFIGURABLE LOGIC BLOCKS

A CLB can contain several slices, which make up a single CLB. Xilinx Virtex-5 FPGAs (right) have two slices: SLICEL (logic) and SLICEM (memory).

In addition to the basic CLB architecture, the Virtex-5 contains wide-function MUXs which can implement:- 4:1 MUX using 1 LUT- 8:1 MUX using 2 LUTs- 16:1 MUX using 4 LUTs

LOOK-UP TABLES (2:1 MUX EXAMPLE) Configuration memory holds output of truth table

entries Internal signals connect to control signals of

MUXs to select a values of the truth tables for any given input signals

LUT BASED RAM

Normal LUT mode performs read operation

Address decoders with WE generates clock signals to latches for write operation

Smaller RAMs can be combined to create larger RAMs (up to 64-bit in Virtex-5)

FPGA PROGRAMMABLEINTERCONNECTION NETWORK

Horizontal and vertical mesh of wire segments interconnected by programmable switches called programmable interconnect points (PIPs). These PIPs are implemented using a transmission gate controlled by a memory bits from the configuration memory.

Consists of global routing connecting PLBs to I/O buffers, non-adjacent PLBs, and other embedded components. Local routing connects PLBs to other adjacent PLBs and PLBs to global routing (done through a switch matrix)

Several types of PIPs are used Cross-point = connects vertical or horizontal wire segments allowing turns Breakpoint = connects or isolates 2 wire segments Decoded MUX = group of 2^n cross-points connected to a single output configure by n configuration

bits Non-decoded MUX = n wire segments each with a configuration bit (n segments) Compound cross-point = 6 Break-point PIPS (can isolate two isolated signal nets)

PROGAMMABLE INPUT/OUTPUT CELLS Bi-directional Buffers

Programmable for inputs or outputs Tri-state controls bi-directional operation Pull-up/down resistors FFs/ Latches are used to improve timing issues

Set-up and hold times Clock-to-out delay

Routing Resources Connections to core of array

Programmable I/O voltage and current levels

Boundary Scan Access

FPGA CONFIGURATION INTERFACES

Master (Serial or Parallel) FPGA retrieves configuration from ROM at initial

power-up Slave (Serial or Parallel)

FPGA configured by an external source (i.emicroprocessor/ other FPGA)

Used for dynamic partial re-configuration Boundary Scan

4-wire IEEE standard serial interface used for testing

Write and read access to configuration memory Interfaces to FPGA core internal routing network

BOUNDARY SCAN CONFIGURATION

Daisy Chain Configuration

Multi-FPGA Emulation Framework to support NoC design and verification (UNLV NSIL)

Test Access Point (TAP) controller composed of 16 state FSM

Developed to test interconnect between chips on PCB

FPGA CONFIGURATION TECHNIQUES Full configuration and readback

Simple configuration interface Automatic internal calculation of frame address

Larger FPGAs have a longer download time Compressed configuration

Requires multiple frame write capability Identical frames of configuration data are written to multiple

frame addresses Extension of partial re-configuration interface capabilities

Frame address is much smaller than frame of configuration data

Reduces download time for initial configuration depending on regularity of system function and the array percent that is utilized

Partial re-configuration and readback Only change portions of configuration memory with respect

to reference design Reduces download time for re-configuration

XILINX VIRTEX-5 FPGAS

Multi-FPGA-based emulation framework for NoC design and verification (UNLV Networking and System Integration Laboratory)

VIRTEX-5 FPGA PLATFORMS•Over 320,000 PLBs on the largest Virtex-5

•ExpressFabric interconnect sturctureand 12 levels of metal interconnect allowing implementation of complex logic functions allowing connections to neighboring PLBs in few hops than Virtex-4

•Each PLB contains 8 LUTs, 8 configurable memory elements (can be configured as RAM/ ROM/ shift register)

•Enhanced DSP functions on 25 x 18-bit multipliers (ability to be cascaded)

•Clock managments contain one PLLC and two managers which can drive global l k b ff d fil ji ( d d)

Five Virtex-5 Platforms1. LX- general logic

applications2. LXT- logic with advanced

serial connectivity3. SXT-signal processing

applications with advanced serial connectivity

4. TXT- high performance systems with double density advanced serial connectivity

5. FXT- high performance embedded systems with advanced serial connectivity

VIRTEX-5 CLB

A single CLB in Virtex-5 consists of two slices: SLICEL (logic) and SLICEM (memory). Each CLB is connected to a switch matrix which can access to a general routing (global) matrix.

Every slice contains four LUTS, wide function MUXs, carry logic, and configurable memory elements. SLICEM support storing data using distributed RAM and data shifting with 32-bit shift registers

SLICEL

SLICEM

FPGA DESIGN COMPARISON VIRTEX-5, VIRTEX-6, AND SPARTAN 6

Virtex-6 CLB have the same setup as Virtex-5 (SLICEL & SLICEM)

Virtex-6 devices add four additional storage elements which can only be configured as edge-triggered D-FFs. The D inputs are driven by the output of the LUTs or bypass slice inputs AX-DX

FPGA DESIGN COMPARISON VIRTEX-5, VIRTEX-6, AND SPARTAN 6

Spartan-6 CLB columns are separated into two columns: 1 column for a new SLICEX and 1 column for alternating SLICEL and SLICEM. SLICEX is a basic CLB without any carry logic added

BACK TO VIRTEX-5 CLB LUT Up to 207, 360 LUTs (6-input) with greater than

13 million configuration bits. Can be configured as dual-output 5-input LUTs.

In single 6-input LUT, O6 is the primary output.

Output MUX (A6)

Output A5

LUT 1 LUT 2

Inputs to LUT 1 & Select Lines

Inputs to LUT 2

LUT SCHEMATIC SIMULATION

Logical AND

Logical OR

VIRTEX-5 PROGRAMMABLE I/O

The I/O cells in Virtex-5 have output logic blocks (OLOGIC) , input logic blocks (ILOGIC), I/O delays blocks, and a bidirectional I/O buffer.

OLOGIC implements registers to improve system clock-to-output timing and supports single data-rate (SDR) and double data-rate (DDR) reception of data. It can also perform parallel-to-serial conversion of output data (2 & 6 bits) in Serial/De-serializer (SerDes) mode.

ILOGIC implements registers to improve set-up and hold times and support SDR and DDR transmission of data. It can perform serial-to-parallel conversion of input data(2 & 6 bits) when in SerDes mode.

Two I/O cells are grouped to form a single I/O tile. In master/slave mode, two I/O cells in the same I/O tile are connected via dedicated shift routing to support larger data widths.

VIRTEX-5 PROGRAMMABLE I/O

FPGA PROGRAMMABLEINTERCONNECTION NETWORK

Horizontal and vertical mesh of wire segments interconnected by programmable switches called programmable interconnect points (PIPs). These PIPs are implemented using a transmission gate controlled by a memory bits from the configuration memory.

Consists of global routing connecting PLBs to I/O buffers, non-adjacent PLBs, and other embedded components. Local routing connects PLBs to other adjacent PLBs and PLBs to global routing (done through a switch matrix)

Several types of PIPs are used Cross-point = connects vertical or horizontal wire segments allowing turns Breakpoint = connects or isolates 2 wire segments Decoded MUX = group of 2^n cross-points connected to a single output configure by n configuration

bits Non-decoded MUX = n wire segments each with a configuration bit (n segments) Compound cross-point = 6 Break-point PIPS (can isolate two isolated signal nets)

VIRTEX-5 FPGA INTERCONNECTIONNETWORK

Global routing consists of Long Lines= routing has three connections: beginning,

middle, and end. Double lines have five connections into a switch matrix between beginning and end, and can source in all four directions of the FPGA from a switch matrix. Every direction has 10 BEGs, MIDs, and ENDs (all bi-directional) for a total of 240 wire segments per switch matrix. Spans 24 rows/columns of components with a switch matrix connection at every sixth component

Double Lines= resources span three columns/rows of components, with a connection to the switch matrix for each component.

Hex lines = three connections into a switch matrix similar to long lines. Source in all four directions from switch matrix. Spans six rows or columns of components

VIRTEX-5 FPGA INTERCONNECTION NETWORK

PIPs

HANDS ON DEMONSTRATION

FUTURE FPGA DEVELOPEMENT

Moore’s law states that the number of transistors on a IC circuit doubles every two years.

How to continue with the trend stated by Moore??

3D Integrated Circuitry

2D INTEGRATED CIRCUIT

Si Substrate

Active device layer

Metal layer 1

Metal layer 2

Metal layer 3

Metal layer 6

TRANSISTORS NO LONGER DOMINATE, METAL INTERCONNECTIONS TOOK OVER

DESIGN COSTS INCREASE AS TECHNOLOGY GETS SMALLER

IC DESIGNS DECREASE

FPGAS SEE DIMINISHING BENEFITS WITHSCALING

90% of FPGA logic area is programmable interconnect

Performance and power penalty are direct result of the area (70% Virtex-2)

Interconnect needs to increase faster than number of gates to keep up (Rents rule)

60%16%

14%

10%Interconnect

Logic

Clocking

IOB

Dynamic Power in Virtex-2 (Shang FPGA’02)

CROSS-TALK INCREASE AS TECHNOLOGYGETS SMALLER

3D INTEGRATED CIRCUITS

•More functionality in a smaller space extends Moore’s Law•More transistors in a package larger designs•Shorter Interconnects less RC delays better chip performance•Power Decrease shorter wires reduce power consumption by producing less capacitance (also less inductance)•Bandwithlarge number of vertial vias between layers allow construction of wide bandwidth buses between functional blocks in different layers

3D INTEGRATE CIRCUIT

Si Substrate

Device layer 1

Metal layers

Device layer 2

Metal layers

Young-Su KWON (MIT) 2005

NUPGA® ARCHITECTURE ( ACHIEVE SAMEDENSITIES AS AN ASIC DESIGN?

Uses a graphite-based memory process for creating reprogrammable memory elements, which is now being used as anti-fuses for 3D FPGAs.

Anti-fuses start as an open circuit, but can be reprogrammed to create a low-resistance with a high voltage. Since the anti-fuses lay above the logic, the interconnection density can rival ASICs. The problem is that high voltage programming transistors take up a lot of area negating the density boost. NuPGA claims they have solved that problem by burying the programmable transistors in a 3D foundation layer beneath the FPGA circuitry

QUESTIONS?