beetle /multi interface hub - diebold nixdorf · 01750299659a beetle /multi interface hub - user...

BEETLE /Multi Interface Hub

User manual

Table of contents

2 BEETLE /Multi Interface Hub - User manual 01750299659A

Table of contents1 Manufacturer´s Certification....................................................... 4

2 Important notes.......................................................................... 52.1 Safety Information .......................................................................... 52.2 System maintenance....................................................................... 7

3 Introduction ............................................................................... 83.1 About This Manual .......................................................................... 83.2 Warranty ......................................................................................... 93.3 Recycling ....................................................................................... 10

4 Before Putting Into Service ....................................................... 114.1 Checking the Scope of Supply ....................................................... 114.2 Setting up the Hub ........................................................................ 124.2.1 Horizontal...................................................................................... 134.2.2 Vertical .......................................................................................... 14

5 Exterior..................................................................................... 16

6 Interfaces and Status Display .................................................... 176.1 COM a and COM b ........................................................................ 186.2 LAN (RJ45) ..................................................................................... 196.3 COM c* and COM d*..................................................................... 196.4 LAN pass through (2x RJ45)........................................................... 206.5 Status display ................................................................................ 216.6 USB-B 3.0 Uplink ........................................................................... 216.7 USB-A 3.0 ...................................................................................... 226.8 PoweredUSB 2.0 ........................................................................... 236.9 Cash drawer (RJ12) ....................................................................... 246.10 Power supply (19 V DC out) .......................................................... 266.11 Power supply (24 V DC out) .......................................................... 266.12 Power supply (24 V DC in)............................................................. 27

7 Cabling the BEETLE /Multi Interface Hub................................... 28

Table of contents

01750299659A BEETLE /Multi Interface Hub - User manual 3

8 Appendix .................................................................................. 308.1 Technical Data............................................................................... 308.2 Block Diagram ............................................................................... 318.3 Total Power Consumption Interfaces ........................................... 328.4 Abbreviations................................................................................ 34

Manufacturer´s Certification


1 Manufacturer´s CertificationThis device meets the requirements of the EU Guidelines2014/30/EU "Electromagnetic Compatibility" and 2014/35/EU“Low Voltage Directive” and 2011/65/EU "Restriction of Haz-ardous Substances". For this, it bears the CE label on the rear side or the icon is printedon the packaging.

Important notes


2 Important notesThe device may be repaired only by authorized qualified person-nel. Improper repairs will lead to the loss of any liability claims.

2.1 Safety Information

The BEETLE /Multi Interface Hub corresponds to the pertinent safety pre-cautions pertaining to data processing facilities.

– If this device is moved from a cold environment to its working environ-ment, condensation may occur. The device must be absolutely dry priorto commissioning, therefore allow for an acclimatization time of atleast two hours before putting it into operation

– The external power supply unit is fitted with a safety-tested power ca-ble. Only the released 24 V/5 A power supply unit (see chapter "Check-ing the Scope of Supply") which is connected to a properly groundedcontactor contact socket is permitted to be used.

– When installing the device, please ensure that the device plug-in fix-ture and the protective contact electrical socket are easily accessible.

– The device must be fully disconnected from the supply voltage whenperforming any work at the device and when inserting or removingdata cables. To completely disconnect the appliance from the mainsvoltage, switch off the device and unplug the power plug of the powersupply unit.

– USB devices may be connected to the system or removed from it dur-ing ongoing operations if these devices comply with the specificationspursuant to usb.org. Other peripherals (e.g. PoweredUSB printer)should not – for safety reasons – be connected to or disconnected fromBEETLE systems unless such systems are switched off.

Important notes


– Before you begin any assembly work on the device, you should dis-charge yourself, e.g. by touching a grounded object (such as a radiator).

– Please make sure that no objects (e.g. paperclips) are able to enter theinside of the device, as this may result in electrical shocks or short cir-cuits.

– No data cables may be plugged in or unplugged during storms.

– Protect devices from vibrations, dust, moisture and heat.

– Make sure that used parts are disposed of in a way that is environmen-tally compatible.

– In the event of emergencies (e.g. damaged housing or damaged powercable, penetration of liquids or foreign bodies), switch the device offimmediately, pull the power plug and inform the technical customerservice of Diebold Nixdorf International GmbH or the authorized ser-vice partner of your dealer.

– Your BEETLE /Multi Interface Hub is the result of state-of-the-art tech-nical innovation. Please ensure therefore equally state-of-the-art con-structional and technical ambient conditions to permit flawless and ef-ficient functioning of the Interface Hub. You should connect the Inter-face Hub or any other IT system only to power supply networks withseparate protective conductors (PE). This type of power supply network is called a TN-S network. Do not usePEN conductors! Please also observe the recommendations of DIN VDE0100 part 540, Annex C2. This will help you avoid any potential mal-functions.

Important notes


2.2 System maintenance

Clean your system at regular intervals with a dry, lint-free cloth. Forgreater amounts of soiling, please use a cleaning agent suitable for plasticsurfaces, as can be ordered from Diebold Nixdorf International. Make surethat the device is deactivated during cleaning, that the power plug is dis-connected and that no fluid enters the inside of the device.

Introduction


3 IntroductionThe BEETLE /Multi Interface Hub provides a large number of classic periphery interfaces for the required devices and thus acts as a servicepoint for each individual POS workplace.

This means that the POS-specific periphery devices are connected to thePOS system via the Multi Interface Hub by only a single cable, by means ofa USB uplink cable.

In the event of error and replacement of the POS system, the entire pe-riphery remains on the Hub. The replacement of the POS system is thusaccomplished exceptionally quickly.

No matter which configuration you may require, Diebold Nixdorf can pro-vide you with the correct solution.

In case of questions about your BEETLE /Multi Interface Hub or otherproducts and solutions of Diebold Nixdorf, please visit us on the Internet.

3.1 About This Manual

The objective of this document is to aid you in the use of the system andalso enable you to use the Table of Contents to find the desired informa-tion quickly.

NOTICE

Notes in the manual are marked by this symbol

Introduction


CAUTION

Attention notifications are identified by this sign.

As the type and scope of the application programs depend on the individual specific choice of each customer, this manual will not deal withany detailed issues pertaining to software. Dedicated manuals are avail-able for the peripherals that can be connected. These devices will there-fore not be described in detail here. Please inform yourself by studying therespective manuals.

3.2 Warranty

In general, Diebold Nixdorf (DN) guarantees a warranty of 12 months afterdelivery or acceptance date. This warranty covers all defects that have oc-curred during normal use of the product.

Defects resulting from incorrect or inadequate maintenance, incorrect useor any unauthorized changes to the product, unsuitable locations or un-suitable environments are not covered.

More details about the warranty regulation can be found in your contractdocuments.

If no claim to product warranty exists and if you do not have a service con-tract with Diebold Nixdorf, then the Customer Care Center (CCC) is avail-able for accepting orders without a contract.

Tel.: 0180 1 (Vanity Number, subject to a charge) Tel.: 0180 1 1 99 2 99 (subject to a charge)

Introduction


3.3 Recycling

This product was designed in accordance with our internal standard "Envi-ronmentally friendly product design and development".

The system is manufactured without the use of CFC and CHC and the ma-jority of the components and materials used in its manufacture are recy-clable.

You are helping us with the recycling if you do not attach any labels to thedevice.

For materials which currently cannot be used for a new purpose, DieboldNixdorf International offers environmentally friendly disposal at a recy-cling center that is certified in accordance with ISO 9001 and ISO 14001.

If your system can no longer be used, please send it in for this environ-mentally friendly and contemporary form of recycling.

Additional information about returns, recycling and disposal of our prod-ucts can be obtained from your responsible branch office or from our recy-cling center in Paderborn.

mailto:[email protected]

We look forward to your E-mail.

mailto:[email protected]

Before Putting Into Service


4 Before Putting Into Service4.1 Checking the Scope of Supply

Unpack the parts and check whether the scope of supply corresponds withthe parts listed on the delivery note.

The BEETLE /Multi Interface Hub is in the box.

Should you detect any transport damages or inconsistencies betweenpackage content and the delivery note, please inform your contractualpartner or sales outlet of Diebold Nixdorf immediately. Please specify de-livery note number, delivery note item number and serial number of thedevice when doing so.

The serial number is located on the label below the barcode.

The following parts for the operation of the Multi Interface Hub should beincluded in the order:

Article no. D-CRNT-24V-V1 (01750266555) Power Supply 24 V/5 AArticle no. D-CRKB-1030 (01750298989) USB 3.0 Uplink cable 1.8 mArticle no. D-CRKB-1031 (01750283504) power supply cable (for the BEETLE /iPOS plus POS system)

Alternative/option available for ordering:



Article no. D-CRKB-1032 (01750298073) power supply cable (for the AURES YUNO POS system)We recommended keeping the original packaging for any subsequenttransporting (protection against jolts and impact).

4.2 Setting up the Hub

Fasten or set up the BEETLE /Multi Interface Hub in such a way that theHub is not exposed to any extreme ambient conditions. Protect the Hubagainst vibrations, dust, moisture, heat and strong magnetic fields.

CAUTION

Installation heigth shall not exceed 2 m above floor.

Take care to ensure that you maintain a minimum distance of 50 mm (1.97 in.) around the device.



Use commercially available screws for the fastening which are adapted tothe subsurface. To fasten the hub, use screws with a screw head diameterof 5-8 mm (0.20-0.31 inches), with a shaft diameter of max. 4.2 mm (0.17 inches).

Even if you want to incorporate the device, it is mandatory that you ad-here to the specified minimum distances and ensure constant aerationand ventilation. The immediate ambient temperature around the Hub maynot exceed 40°C.

4.2.1 Horizontal

On the underside can be found four stands, each provided with a anti-sliprubber foil.

The BEETLE /Multi Interface Hub can be fastened horizontally above or be-low.



Illustration 1: Horizontal installation, above

Illustration 2: Horizontal installation, below

4.2.2 Vertical

In order to ensure that correct ventilation continues to be guaranteed, thefollowing minimum distances must be maintained for free convection,even with with vertical setup:

Around all 5 sides of the device: 50 mm (1.97 inch)

You can fasten the suspended BEETLE /Multi Interface Hub on either theleft or the right.



Illustration 3: Vertical installation

Exterior


5 ExteriorThe following illustration shows the BEETLE /Multi Interface Hub from thefront.

Rear view:

Interfaces and Status Display


6 Interfaces and Status Display

1 COM a Standard RS232(plug)

2 LAN 10/100/1000 Mbit/s

3 COM b Standard RS232 (plug)

4 COM c* RS232 powered (socket)

5 COM d* RS232 powered (socket)

6 LAN Pass-through (RJ45/RJ45)

7 Status display 8 USB-B 3.0 Uplink9 4 x USB-A 3.0 10 3 x powered USB 2.0/12V

11 PoweredUSB 2.0/24V 12 Cash drawer (RJ12)13 Power supply 19 V

(DC out) only as alternative to(15) for Aures YUNO POS system

14 Power supply 24 V (DC in)

15 Power supply 24 V (DC out) for BEETLE /iPOS plus

*supplied with power supply

CAUTION

Do not plug in data or power supply cables if the system is plugged in!



CAUTION

Never use the 24 V (DC out) and 19 V (DC out) power supplies together.

6.1 COM a and COM b

Connect for example a scale with dedicated power supply to the COM a orCOM b interface. COM a and COM b are designed as 9-pin D-Sub plugs.

Interface connector (COM/DVI/VGA) with knurled screw can be disen-gaged by hand.

PIN Function1 DCD – Data Carrier Detect2 RXD – Serial Data In3 TXD – Serial Data Out4 DTR – Data Terminal Ready5 GND6 DSR – Data Set Ready7 RTS – Request to Send8 CTS – Clear to Send9 RI - Ring Indicator



6.2 LAN (RJ45)

The cable for the connection to a network (LAN) will be plugged in here.

LEDs

Left LED Constant green Network connection es-tablished

Flashes green Data transferRight LED off 10 MBit

Constant green 100 MBitConstant orange 1000 MBit

This LAN connection is provided through an internal USB 2.0 interface. De-vice drivers for Windows and Linux operating systems are available.

NOTICE

Use only shielded LAN cables marked with a CAT5 or CAT5e (for 1000MBit). These offer greater protection against malfunctions in the net-work.

NOTICE

The Multi Interface Hub and the POS system each has a MAC address ofits own.

6.3 COM c* and COM d*

Each of these is a 9-pin power-supplied D-Sub socket.



NOTICE

Scanners, customer or operator displays without dedicated power sup-plies will be connected to this interface independent of the existing con-figuration (see chapter "Total Power Consumption").

WARNING

Take care to ensure that the plug for the peripheral devices is tightlyscrew-connected with the socket because otherwise malfunctions couldoccur. The power supply is provided through this socket.

PIN Function1 +12 V2 RXD – Serial Data In3 TXD – Serial Data Out4 DTR – Data Terminal Ready5 GND6 DSR – Data Set Ready7 RTS – Request To Send8 CTS – Clear To Send9 + 5 V

6.4 LAN pass through (2x RJ45)

It may happen in some installation environments that the installed LANconnection (via USB) cannot be used. The Multi Interface Hub thereforeoffers a so-called LAN pass-through, meaning the Hub can be used to loopthe LAN through to the POS system.



The plugs for the LAN pass-through connection can be plugged at randominto two available sockets.

LAN in: Network infrastructure connection

LAN out: Connection to the POS system

NOTICE

The LAN pass-through interface of the Hub has no MAC address of itsown. The MAC address of the POS system applies.

6.5 Status display

Two LEDs indicate the current status of the BEETLE /Multi Interface Hub.

The green LED indicates that an USB uplink from the system is in effect. The red LED reports an overcurrent event when the power consumption ofthe Hub and the connected peripherals is exceeded. In this case discon-nect one or more devices from the hub. Please see chapter “Total powerconsumption interfaces” for more information.

6.6 USB-B 3.0 Uplink

This connection is used to set up the connection between the BEETLE /Multi Interface Hub and the POS system via USB Uplink cable.Take care to ensure while doing so that this cable matches the currentUSB specifications.



PIN Function1 + 5 V2 USB data-3 USB data+4 GND5 StdA:SSTx-6 StdA:SSTx+7 GND8 StdA:SSRx-9 StdA:SSRx+

6.7 USB-A 3.0

Various USB peripherals can be connected to these connections (USB-A3.0), e.g. not only scanners, scales or dongles, but also even graphic cardsor monitors. USB can provide the required power for devices with littlewattage such as keyboards.

NOTICE

Only devices and cables that are in accordance with the valid USB specifi-cations can be connected to the USB interfaces.



PIN Function1 + 5 V2 USB data-3 USB data+4 GND5 StdA:SSRX-6 StdA:SSRX+7 GND8 StdA:SSTX-9 StdA:SSTX+

6.8 PoweredUSB 2.0

USB peripherals, whose energy demand is higher than the supply providedby the standard USBs, e.g. printers, barcode scanners or displays, can beoperated at PoweredUSB ports.

WARNING

The power supply is 24 V (marked in red, for POS printers) or 12 V(marked in turquoise) (see chapter "Total Power Consumption").

A mechanical coding prevents a USB 12 V plug from being accidentallyplugged into a USB 24 V socket. The lower half of the PoweredUSB socketcan also be used as a USB-A socket.



Illustration 4: 12 V

Illustration 5: 24 V

PIN Function1 + 5 V2 USB data-3 USB data+4 GND5 GND6 +12 V or +24 V7 +12 V or +24 V8 GND

6.9 Cash drawer (RJ12)

The system includes an RJ12 socket for the connection of a cash drawer.This connection must be used only to connect a till drawer.

NOTICE

Please ensure that the plug has a tight contact with the socket becauseotherwise it can lead to malfunctions.

Once plugged in, RJ12 plugs are locked. The power supply (P24V +5% /-15%) of the cash drawer is provided through this socket.



CAUTION

The connection of sub-drawers (the so-called looping through) and theconnection of 12 V OEM till drawers is not permitted!

PIN Function1 FG – Frame ground2 OPEN1 – Opening signal

for drawer3 KLE1N – Status drawer

(open/closed)4 +24 V – Supply voltage5 <not used>6 GND – Signal Ground

The till drawer interface is addressed on the system side via a virtual COMport.

RS-232 settings:

– Baud rate 1200

– 8 Bits

– 1 stop bit

– No parity

– No flow control

Commands:

– Info: 0x1d 0x49 (GS I)

Answer: "Cash Drawer"

– To open: 0x1b 0x70 (ESC p)



– Status query: 0x1b 0x75 (ESC u)

Answer: "0" or "1" (depending on the till drawer used)

6.10 Power supply (19 V DC out)

The power supply of the AURES YUNO POS system is provided through thissocket as an alternative to the 24 V DC out.

Use the power supply cable that can be ordered from Diebold Nixdorf (seechapter "Checking the Scope of Supply").

PIN Function1 +19 V out2 GND3 Power Control

CAUTION

Never use the 24 V (DC out) and 19 V (DC out) power supplies together.Only connect cables to the 24V and 19V connectors which are markedwith DP-1 or DP-2.

6.11 Power supply (24 V DC out)

The power supply of the BEETLE /iPOS plus POS system is providedthrough this socket.



PIN Function1 GND2 +24 V out3 GND4 +24 V out

6.12 Power supply (24 V DC in)

The power supply is provided through this socket. Please plug the appro-priate end of the power cable of the external power supply unit into thissocket. Pull on the sleeve of the locked plug to deenergize the device.

PIN Function1 GND2 +24 V in3 GND4 +24 V in

Cabling the BEETLE /Multi Interface Hub


7 Cabling the BEETLE /MultiInterface HubAll devices that are part of the BEETLE /Multi Interface Hub and that havetheir own dedicated mains voltage cable must be connected to the samecircuit.

– Please ensure that all data cables are plugged in at the Hub and thatthe peripherals are plugged in.

– Use cable ties to secure the cables. A cable tie can be used to secureplugs without interlocks against being pulled out accidentally. Pull thecable tie (1) through the pre-punched opening in the sheet metal. Sur-round the cable and pull the cable tie tight.

– Next, plug the power supply cable into the 24 V (DC in) socket of theBEETLE /Multi Interface Hub.

Cabling the BEETLE /Multi Interface Hub


– Plug the power cable into the socket of the external power supply andplug the other end into the protective contact electrical outlet of thehouse installation.

– The device is ready for operation as soon as a USB uplink signal is pre-sented via the POS system.

NOTICE

Observe the performance specifications in the chapter "Total Power Con-sumption of the Interfaces" in the Appendix of the manual.

Appendix


8 Appendix8.1 Technical Data

SizeWidth 310 mm (12.20 in.)Depth 157 mm (6.18 in.)Height 58 mm (2.28 in.)Weight approx. 1.2 kg (2.64 lb)Ambient conditionen (Temperature)Operation - 5°C to + 40°C (5%-85% r.h.)Transport - 25°C to + 60°C (15%-98% r.h.)Storage - 5°C to + 40°C (15%-85% r.h.)Power supplyInput voltage (24V DC in) max. 5 AOutput voltage (24 V DC out) max. 5 AOutput voltage (19 V DC out) max. 3.5 AInterfacesRS232 standard (non-pow-ered)

2

RS232 powered 2USB A 3.0 4PoweredUSB 12 V/24 V 3/1Cash drawer (24 V) 1LAN (10/100/1000 Mbit/s) 1SoftwareOperating System Support POSReady 7 32-bit/64-bit

Windows 7 Prof. 32-bit/64-bitWindows 10 ioT Enterprise 2016 LTSBWNLPOS4 64-bit (Linux)

Cash drawers driver Legacy Support, JavaPOSCOM via USB Driver from the chip manufacturer (FTDI)

Appendix


LAN Driver from the chip manufacturer (Real-tek)

8.2 Block Diagram

Appendix


8.3 Total Power Consumption Interfaces

The total power consumption at 5 V interfaces must not exceed 6 A:

Every COM* = 300 mA, total of 600 mAEvery PoweredUSB2.0 = 500 mA each portEvery USB 3.0 = 900 mA each port

The total power consumption at 12 V interfaces must not exceed 3 A:

COM* = 600 mA, total of 900 mAEvery PoweredUSB 2.0 = 1.5 A, total of 3 A

Voltage Power per port Power across allports

RJ12 socket/cashdrawer

22….24 V 1 A (max. 250 ms) -

12 V Powere-dUSB

12 V 1.5 A 3 A

24 V Powere-dUSB

24 V 3 A -

P-USB (USB 2.0) 5 V 0.5 A 2 AUSB-A 3.0 5 V 0.9 A 3.6 ACOM a/b (D-Sub) - - -COM c*/d*(power-suppliedD-Sub)

5 V/12 V 0.3 A / 0.6 A 0.6 A / 0.9 A

Output voltage (24 V DC out) max. 5 AOutput voltage (19 V DC out) max. 3.5 A

The 24 V PoweredUSB interface is provided for the operation of retailthermal printers authorized by Diebold Nixdorf.

Appendix


CAUTION

The power consumption of the attached devices must not exceed 100Win total. In case of doubt please get in contact with your service provideror DN.

Appendix


8.4 Abbreviations

Abbreviations DescriptionsA AmpereCE European Symbol of ConformityCOM RS232 interfaceCOM* RS232 interface, power suppliedDIN Deutschen Institut für Normung (German Institute

for Standards)D-Sub D-Shaped SubminiatureEFT Elektronischer Zahlungsverkehr (Electronic funds

transfer)ESD Electrostatic Sensitive DevicesEU European UnionISO Internationale Organisation für Normung (Interna-

tional Organization for Standardization)LAN Local Area NetworkLED Light Emitting DiodePEN conductor Protective Earth Neutral ConductorPOS Point of SalesRJ Registered Jack (genormte Buchse), e.g. RJ45TN-S Terre Neutre SeparéUSB Universal Serial BusV VoltVDE Verband für Elektrotechnik, Elektronik und Infor-

mationstechnik e.V. (Association for Electrical,Electronic & Information Technologies)

W WattWLAN Wireless Local Area Network


notesnotes

Published byWincor Nixdorf International GmbHWohlrabedamm 3113629 BerlinPhone: +49 (0) 30 / 50 17-0Fax: +49 (0) 30 / 50 [email protected]

© Wincor Nixdorf International GmbH Berlin

Order No. 01750299659APrinted in Germany, September 2017

beetle /multi interface hub - diebold nixdorf · 01750299659a beetle /multi interface hub - user...

Documents