bedding in racing brake pads & discs · 2020-03-10 · our racing brake pads and discs are also...
TRANSCRIPT
BEDDING INRACING BRAKE PADS & DISCS
GET THE MAXIMUMOUT OF YOUR BRAKESIf pads and discs are not bedded in properly, the brake system will not achieve its maximum performance, wear behavior, pedal feel and lifetime.
Therefore, correct bedding in of brakes is absolutely essential.
IMPORTANCE OF BEDDING IN FOR THE BEST BRAKE PERFORMANCE
The bedding in procedure for PAGID Racing brake pads and discs is identical.
TECHNICAL INFORMATION
During the bedding in procedure the brake materials are optimally prepared to achieve the best brake performance.
Burn out volatile elements
Transfer a layer of friction material onto disc
Mechanically align pad surface with disc surface for full contact patch
1 BREAKING INOUT LAP
ATTENTIONTry to avoid installing a new disc and a new brake pad at the same time. Please replace only one component at a time.
If the brake disc has been used before, please make sure that the brake pad compound is compatible with the friction layer on the disc. For any questions please contact your dealer.
RECOMMENDED ON-VEHICLE BEDDING IN PROCEDURE FOR RACING BRAKE PADS AND DISCS
10 stops with mid pressure / low temperature from 150 km/h (90 mph) to approximately 80 km/h (50 mph).
2 A sequence of 5 stops with medium to high pressure from 180 km/h (110 mph) to approximately 60 km/h (40 mph) with maximum acceleration between the stops.
3 RECOVERY STOPS IN LAP
3 to 5 stops with mid pressure from 150 km/h (90 mph) to approximately 80 km/h (50 mph).
HEATING UP FAST LAP (RACE SPEED)
Our racing brake pads and discs are also available pre-bedded “ready to race”.
Using pre-bedded parts is always recommended, as they have been run in in a computer-controlled environment and can therefore deliver perfect performance at very reasonable costs.
Keep in mind that every lap on a race track is expensive.
Get the maximum out of your brakes with a minimum amount of time while saving bare money – get pre-bedded parts!
USAGE OF PRE-BEDDED PARTSBEDDING IN SERVICE
PAGID Racing brake products have been optimised for your individual requirements and provide the perfect solution for every purpose: Endurance • Sprint • FormulaTrack Days • Club Sport • AllroundRally • Stock Car • Historic Cars
MAXIMUM PERFORMANCE FOR EVERY
PURPOSE
All over the world, numerous motorsport teams in the most varied racing categories successfully rely on PAGID Racing’s quality and reliability.
BEDDING INBRAKE PADS / DISCS (MPH)
OUT LAP
FAST LAP (RACE SPEED)
IN LAP
> 5 x BRAKING 110 40 mph
= HIGH PRESSURE
10 x BRAKING 90 50 mph
= MID PRESSURE
> 5 x BRAKING 90 50 mph
= MID PRESSURE
> 5 x BRAKING 180 60 km/h
= HIGH PRESSURE
10 x BRAKING 150 80 km/h
= MID PRESSURE
> 5 x BRAKING 150 80 km/h
= MID PRESSURE
BEDDING INBRAKE PADS / DISCS (KM/H)
OUT LAP
FAST LAP (RACE SPEED)
IN LAP
RECOMMENDED ON-VEHICLE BEDDING IN PROCEDUREPrint it, cut it and stick it in the cockpitto support your driver.
The available specifications and possible applications can be found in our detailed product search at www.pagidracing.com.
Your PAGID Racing Dealer
EUROPE
TMD Performance GmbHLüschershofstr. 80D-45356 EssenGermany
USA
TMD Performance, SMLLC1035 Crooks RoadTroy, MI 48084USA
www.pagidracing.com
© PAGID Racing 2020