because there’s space

Because there’s space for efficiency and sustainability everywhere. Drainage systems

parkline

Sustainable innovation.

Drainage systems in car parks are a necessity and faced with a wide range of challenges – which are not quite met by traditional rectangular gutter systems. FILCOTEN® parkline is a different story: our system shows that HPC, a modern mineral high performance concrete combined with a sophisticated structure, is the right solution for any challenge.

The best drainage performance with maximum efficiency.Alongside optimized drainage performance, the parkline system also offers a variety of properties for entirely new opportunities for increasing efficiency, both during installation and in day to day use.

Floor drainDN 100

More potentialjust drainage.

than anyone else – in not more than

Intelligent drain cover- Drain cover made from V2A stainless steel- Can easily be removed for cleaning- Functions as a sturdy cover and walkway

bridge and thus increases accessibility

Comb Profile- suitable for wheelchairs- Slot width of 12.5 mm, 17 mm or 18 mm,

based on requirements of EN 1433- Almost no height difference from

the surrounding roadwayDrainage-optimized

channel bodyThe draining water is channeled into the drain in the center via the two branch channels.

Installation height/widthAvailable in three versions:H = 35 mm / W = 150 mm (as shown.) H = 50 mm / W = 150 mmH = 50 mm / W = 300 mm

Very quiet- Even cross-section & monolithic

construction prevent noise when driven over

- No complaints from residents about rattling grates


C250 class

Innovative connecting element- Allows for a wide variety of combinations

for channel runs (cross, T/L connection)- Made entirely from FILCOTEN®, high stability- Efficient water conductivity thanks to

intelligent construction

parkline

Joint raking Pressure washer Sweepers

Sophisticated sealing joint- sealable butt joint, easily accessible and inspectable- based on requirements of EN 1433- In order to create a sealed system and connect

with the surface coating system, a seal should be made below the parkline elements.

Powerful connectionThe coefficient of expansion for FILCOTEN® is identical to that of concrete, meaning that the material is perfectly suited to ensuring a firm fit in the long term.

Perfect fitSide fixing pouches reinforce the firm fit in the concrete bed and ensure additional stability.

Easy cleaning and maintenance• No separate grates• Easy to check for soiling without removing grates• Easy to clean thanks to clear cross section without covers

Installation examples

General information

The installation guidelines and installation examples below are intended for standard applications. The load class and the instal-lation location in accordance with EN 1433 should be adapted during planning to suit the local conditions. The technical policies and guidelines generally recognized should be taken into consider-ation during installation. Please contact BG Application Engineer-ing for special applications.

A FILCOTEN® parkline installation guidelines for asphalt or paving

B FILCOTEN® parkline installation guidelines for concrete surfaces with finishing

1) A Setting of the FILCOTEN® parkline using bitumen lug sealing on a concrete foundation which is at least 2 cm thick in accordance with the Austrian standard B4710-1 or in micro-fine concrete in accordance with RVS 08.18.01 or a flex adhesive spreader. Depending on the structural requirements, a side wheel leveller setting in concrete is required – see cross-sections for details.

1) B Setting of the FILCOTEN® parkline in a recess over an on-site structure seal – in accordance with the listed surface finishing system. The parkline are (selectively) set in the desired position using earth-moist concrete and are then infilled with grouting mortar – see cross-sections for details.

2) A+B Initial setting of the body run at the transition to the drain.

3) A+B The butt joints between the individual channel bodies can be sealed or adhered with a suitable sealant – for material description and quantity determination see BG Sealing System. (www.bg-company.com/sealing_system)

4) A When sealing the superstructure and the surface layer (asphalt, paving), please ensure that the channel bodies are not damaged.

5) A If horizontal forces occur (e.g. in paved surfaces, on slopes, etc.), a sufficiently dimensioned expansion joint is to be provided in the roadway connection area, 30-200 cm from the channel.

6) A If shearing forces occur, paving surfaces must be friction locked with the back supports. This can be accomplished by setting the first three rows of paving slabs (on the channel run) in a bed of mortar. The joints should be back-filled with mineral. Shearing forces on the paving surface should not act directly on the channel walls (e.g. thermal expansion, braking forces, etc.).

7 ) A All adjoining top layers should be 3-5 mm higher than the surface of the channel bodies in order to prevent mechanical damage (e.g. snow removal) and to ensure the inflow of water.

7 ) B All adjoining top layers should slope towards the parkline runs in order to ensure the inflow of water.

8) A+B In areas where chemical attacks (e.g. de-icing chemicals, acids, bases, etc.) are expected, we recommend cleaning soiling off the drainage runs and rinsing them with clean water sufficiently often.

Installation details can be found at: : www.bg-company.com

Installation example: asphalt

Simple, extremely sturdy laying. • Mounting with installation chairs possible • Channel bodies are pre-installed with elevation

and are then completely set in concrete • Fastening with screws ensures quick and

easy laying as well as high stability • No heavy equipment needed for installation • Time and cost-savings during installation • Temporary cover protects the channel body

during concrete pouring

Perfect for renovations. • Can be applied regardless of previously used

systems owing to the flat construction

• Installation in existing recesses

3 mm 3 mm

DN 100

Paving

Sealing level

Microfine concrete

Microfine concrete or adhesive mortar

Steel-reinforced concrete surface

Pipes with trim ring

Installation chair, NW 150, H = 35 mm, galvanized steel

Installation chair, NW 150 & NW 300, H = 50 mm, galvanized steel

parkline

Art. no. Accessories Material Weight Pc./pallet12515081 Cross corner element,150/150/50 mm, H = 50 mm, SW=17 mm FILCOTEN 1,80 kg12515384 Drain cover V2A steel 0,04 kg12515386 Front or end plate V2A steel 0,04 kg

19010902parkline installation chair - set incl. screws required: number of channels +1 galvanized 0,62 kg 50

12515292 Construction cover, 1000/150/14 mm galvanized 1,28 kg12515391 Cleaning rake (without handle) V2A steel 0,22 kg

Art. no. Channel body Slope Weight Pc./pallet12515001 FILCOTEN parkline 150, H = 50 mm, SW = 17 mm 0,0 % 11,9 kg 6012515071 FILCOTEN parkline 151, H = 50 mm, SW = 17 mm, with outlet 0,0 % 11,6 kg 60

FILCOTEN® parkline, nominal width 150 – installation height 50 mm Comb Channel made from FILCOTEN® HPC (High Performance Concrete) up to class C, Capacity: 2,0 l/m

Art. no. Accessories Material Weight Pc./pallet12515084 Cross corner element, 153/153/35 mm, H=35 mm, SW=12,5 mm FILCOTEN 1,34 kg12515383 Drain cover, double bridge V2A steel 0,06 kg12515385 Front or end plate V2A steel 0,02 kg



Art. no. Channel body Slope Weight Pc./pallet12515005 FILCOTEN parkline 150, H = 35 mm, SW = 12,5 mm 0,0 % 9,2 kg 8012515075 FILCOTEN parkline 151, H = 35 mm, SW = 12,5 mm, with outlet 0,0 % 8,9 kg 80


Art. no. Accessories Material Weight Pc./pallet12530080 Cross corner element, 305/305/50 mm, H = 50 mm, SW =18 mm FILCOTEN 7,60 kg12515381 Drain cover V2A steel 0,05 kg12530386 Front or end plate V2A steel 0,09 kg



Art. no. Channel body Slope Weight Pc./pallet12530000 FILCOTEN parkline 300, H = 50 mm, SW = 18 mm 0,0 % 25,3 kg 3012530070 FILCOTEN parkline 301, H = 50 mm, SW = 18 mm, with outlet 0,0 % 25,0 kg 30



Technical specifications: www.bg-company.com/parkline_150_35



50

150

18

15

18

50

15

305

35

15

12,5

150

305

50

15

18

150

50

15

17

150

3515

12,5

50

150

18

15

18

50

15

30535

15

12,5

150

305

50

15

18

150

50

15

17

150

3515

12,5

50

150

18

15

18

50

15

305

35

15

12,5

150

305

50

15

18

150

50

15

17

150

3515

12,5

Sustainable in every respect, high-performance down to the last fiber – or simply FILCOTEN®.

Certified: non-toxic. • Meets the strict criteria of the Rosenheim

Institute for Building Biology (IBR)

• Protects health and the environment

• Guaranteed to be ecologically safe as it is tested for biocides, solvents, VOC, heavy metals and radioactivity

Mineral raw material, recyclable and energy-efficient.FILCOTEN® HPC is a mineral high performance concrete which is 100% recyclable and free from resins and solvents. When it comes to our production, we rely on an environmentally friendly energy mix for production and avoid using fossil fuels to the greatest extent possible.

Environmentally friendly production process.We also focus on environmental protection for the production process – in the choice of raw materials and by avoiding excessive waste. On that note, we have implemented an environmental management system in accordance with the ISO standard 14001.

Material with excellent properties.• FILCOTEN® HPC (High Performance Concrete)

• Cement-bound, mineral material with high bending tensile strength thanks to fiber reinforcement

• Up to 70% lighter than conventional concrete channels

• Temperature, frost and UV-resistant

• Resistant to rust, oil and petrol

• Coefficient of expansion matches the mineral environment

• Long-lasting pleasant appearance

Our corporate culture is based on sustainability and innovation. This is reflected in the materials used and in the production processes. The result: cutting-edge technology in harmony with nature.

Installation example: concrete

• Fire

pro

tecti

on class A1 – non-com

bustible •

FILCOTEN®

DN 100

Roadway surface

Chamfering

Epoxy grouting mortar

Sealing level incl. channel recess

Smoothing with epoxy mortar

Steel-reinforced concrete surface

Pipes with bonding flange

68,23 % Hydroelectric power 15,91 % Biogas 9,58 % Wind power 5,26 % Solid or liquid biomass 1,02 % Other green energy 100 % Sustainable energy mix

As of 2017BG green electricity:

BG-Graspointner GmbHGessenschwandt 39

4882 Oberwang AUSTRIA

Tel.: +43 6233/89 00-0

Fax: +43 6233/89 00-303

E-Mail: [email protected]: www.graspointner.at

Your partner for BG-Graspointner drainage systems.

BG

12.

02.2

019

Innovation & environmental awareness also apply for our print products.

Printed according to criteria documents of the austrian Eco-Label„printed products“. gugler*print, Melk, UWZ-Nr. 609, www.gugler.at

This paper comes from sustainably managed forests and controlled sources.www.pefc.at

* Our contribution to the reforestation project of BOKU Wien in Ethiopia.


carbon positive printed

Höchster Standard für Ökoeffektivität. Cradle to CradleTM zertifizierte Druckprodukte innovated by gugler*.

because there’s space

Documents