BD Quikheel™ Lansetler ve BD Microtainer® MAP Otomasyona Uygun Mikrotüp

BD Microtainer® MAP Otomasyona Uygun Mikrotüp

BD Microtainer® MAP Otomasyona Uygun Mikrotüp, ilk tek parça, otomasyona uygun

mikrotüp olarak karşınızda.

En hassas hasta grubunuza odaklanın ve BD Microtainer® MAP’in örneğinizle

ilgilenmesine izin verin.

Eklenen Özellikler;

Otomasyona uygun delinebilir mikroguard kapak

Kaşıklama yöntemi ile kan toplamaya uygun entegre ağız

Barkod yapıştırmaya ve kolay karıştırmaya uygun orjinal tüp boyutu

Tüp karıştırma sayısını hatırlatan etiket

Üç farklı dolum hacmi belirteci

BD Quikheel™ Güvenlikli İnsizyon Cihazı

BD Quikheel™ Güvenlikli İnsizyon Cihazı ile yenidoğan topuk insizyonu

yaparken kan akışını hızlandırın ve acıyı azaltın. Kolay tek elle kullanımı cerrahi

bıçağın hareketi ile tek hamlede hassas ve tutarlı bir kesi sağlar. İşlem esnasında

bıçağın cihaz içerisine otomatik hareketi kendinizi ve size güvenenleri

beklenmeyen kazalardan korumanızı sağlar..

Eklenen Özellikler;

PKU analizi için yeteli kan akış miktarı

Konik izlem penceresi aynı noktaya iki kesi yapılmasını önler

İnfant ve prematüreler için iki ayrı boy seçeneği

Standart kesi derinliği ile osteomiyelit riskini azaltma

Select a site identified in the shaded area above.Cleanse site thoroughly with alcohol. (70/30 by volume, 70%).Allow skin to air dry.

BD Microtainer ® MAP Microtube for Automated Process Capillary Blood Collection Methods

Performing a Heel Stick

BD Microtainer® Product Offerings

Filling BD Microtainer® Tubes with BD Microgard™ ClosureObtain necessary supplies.Confirm the identity of the newborn.Follow universal precautions.

With a gloved hand, place the BD Quikheel™ Lancet

Device against the site with Single-use Safety Incision

the Quikheel logo facing you.Place the blade slot area securely against the heel.The incision can be placed at a 90º angle to the length of the foot or parallel to the length of the foot.

Conduct Heel Stick as outlined in the “Performing a Heel Stick” section above.The order of draw for microcollection differs from that of venipuncture.If multiple specimens are to be collected, including EDTA specimens, the EDTA specimen is collected first to ensure adequate volume and accurate hematology test results.Additive specimens are collected next.Specimens requiring serum are collected last.Follow twist assist cap removal instructions above.

Firmly and completely depress the trigger with your index finger.

Collect the specimen with the Microtainer tube by allowing the blood to run into the collection funnel while holding at a 30-45° angle.Ensure that the tube is not scraped over the puncture site.

After triggering the lancet, remove the lancet and discard it into a biohazard sharps container.

After blood has been collected from the heel of the newborn, the foot should be elevated above the body.A clean gauze pad should be pressed against the puncture site until bleeding stops.It is not advisable to apply adhesive bandages over skin puncture sites on newborns.Invert the BD Microtainer® MAP Microtube for Automated Process according to label instructions. (K2EDTA – 8x)Mix all other Microtainer Tubes with Microgard Closures with the following inversions:PST – 10x SST – 5xGlucose – 10x Serum – 0x

Gently wipe away the first drop of blood with clean, dry gauze pad.Apply gentle pressure with the thumb and ease intermittently as drops of blood form.Be sure to apply pressure such that the incision is opened.

CLSI H4-A6 Recommended Guidelines*:1. Warming the infant’s heel is essential

for pH and Blood Gases.

2. Warming the heel increases arterial blood flow to the site up to seven-fold without burning the skin.

3. Temperature of warming device should be no higher than 42° C. Warming should be three to five minutes.

Reference Number

Width and Depth (mm)

Blood Volume

ColorPackaging Box/Case Quantities

368100 1.75 x 0.85Low Flow

(Preemie)Pink 50/200

368101 2.50 x 1.00High Flow

(Infant)Teal 50/200

BD Microtainer® Quikheel™ Lancets

Reference Number

DescriptionPackaging Box/Case Quantities

363706 1.0 mg K2EDTA Additive, 13 x 75 mm, Volume 250-500 µL 50/200

BD Microtainer® MAP Microtube for Automated Process

To learn more about BD products and services designed to streamline your lab; send an e-mail to: EMA_PAS@bd.com

* CLSI. H4-A6 Procedures and Devices for the Collection of Diagnostic Capillary Blood Specimens: Approved Standard – Sixth Edition, 2008

BD Microtainer ® MAP Microtube for Automated Process Capillary Blood Collection Methods

BD, BD Logo and all other trademarks are property of Becton, Dickinson and Company.

© 2012 BD

Performing a Fingerstick Collection

Select the site. The patient should be sitting or lying down. Have patient hold their hand in a downward position, allowing gravity to help increase blood supply to the hand.

Twist off tab to break the seal and discard.

To activate, press safety lancet firmly against the puncture site. Do not remove the device from the site until an audible click is heard. Discard used safety lancet into an approved sharps container. Collect the specimen.

Select finger: middle or ring finger is preferable. Identify the desired puncture site (shaded area) and make sure it is properly cleansed with 70% alcohol according to your facility’s established procedures. The site must be allowed to air dry in order to provide effective disinfection and to prevent possible hemolysis or erroneous results from residual alcohol.

CAUTION: Handle all biologic samples and blood collection “sharps” (lancets, needles, luer adapters, and blood collection sets) in accordance with the policies and procedures of your facility. Obtain appropriate medical attention in the event of any exposure to biologic samples (e.g., through a puncture injury) since samples may transmit viral hepatitis, HIV (AIDS), or other infectious diseases. Utilize any safety-engineered feature if the blood collection device provides one. Discard all blood collection “sharps” into biohazard containers approved for their disposal.

Warm the site. Use a warm, moist towel or other appropriate warming device (not more than 42°C) for three to five minutes.

BD Microtainer ® Product Offerings

Reference Number

Width and Depth (mm)

Blood Volume

Color Packaging Box/Case Quantities

366594 1.5 mm x 2.0 High Flow Blue 200/2000

Reference Number

Description Packaging Box/Case Quantities

363706 K2EDTA Additive 1.0 mg, 13 x 75 mm, Volume 250-500 µL 50/200

BD Microtainer® Contact-Activated Lancet

BD Microtainer® MAP Microtube for Automated Process

The order of draw for microcollection differs from that of venipuncture. If multiple specimens are to be collected, including EDTA specimens, the EDTA specimen is collected first to ensure adequate volume and accurate hematology test results. Additive specimens are collected next. Specimens requiring serum are collected last. Follow twist assist cap removal instructions above.

Gently apply intermittent pressure along finger capillaries up to the puncture site. Hold hand below elbow level to obtain the required blood volume. Strong repetitive pressure (milking) must be avoided. Wipe away the first drop of blood with a clean dry gauze pad. Turn the patient’s hand palm down. Position the BD Microtainer® MAP Microtube for Automated Process directly beneath the puncture site. Apply gentle, intermittent pressure along finger capillaries to allow them to refill with blood and to help ensure continuous blood flow. Apply gentle pressure at the ends of the puncture site, opening the puncture site slightly, to maximize blood flow. Ensure that the tube is not scraped over the puncture site. Invert tube according to label instructions. Complete the procedure. Wipe the site dry and apply direct pressure with a clean gauze pad until the bleeding has stopped. Dispose of all used materials according to your facility’s established procedures. Label the tubes and transport them to the lab for processing.

BD Diagnostics - Preanalytical Systems P.O. Box 52279, Dubai United Arab Emirates Tel.: +971 4 337 9525 Fax: +971 4 337 9551 Email: EMA_PAS@bd.com www.bd.com/vacutainer

To learn more about BD products and services designed to streamline your lab; send an e-mail to: EMA_PAS@bd.com

Position the BD Microtainer® Contact-Activated Lancet firmly against the puncture site as illustrated.

Hold safety lancet between fingers.

EMA

-PA

S-00

2