balance grades as per iso 1940
TRANSCRIPT
-
8/13/2019 Balance Grades as per ISO 1940
1/21
-
8/13/2019 Balance Grades as per ISO 1940
2/21
References
Schenck Trebel Corporation
535 Acorn Street
Deer Park, NY 11729
Toll Free: 1-800-873-2352
http://www.schenck-usa.com
http://www.mpta.org/MPTABalancingPrimer.pdf
http://www.irdbalancing.com/downloads/TechPaper1BalQualityReqmts.pdf
-
8/13/2019 Balance Grades as per ISO 1940
3/21
Motor Repairs
Motor Repair Specification
Balance Grades
Initial Balance with Shop Balance Machine
Final Balance with Motor Assembled
-
8/13/2019 Balance Grades as per ISO 1940
4/21
Motor Repair Specification
Work to be performed
Acceptable Repair Practices
Required Reporting
Acceptance Criteria, including BALANCE GRADE.
-
8/13/2019 Balance Grades as per ISO 1940
5/21
Balance Grades
Balance Grades are used to specify the allowable residualimbalance for rotating machinery.
The ISO 1940 standard defines balance grades fordifferent classes of machinery. (Rigid Rotors Only*)
Example: Balance Grade G2.5 is recommended forSteam Turbines, Machine Tools and Small ElectricArmatures.
* ISO 11342 defines the balance quality requirements for rotors in a flexible state
-
8/13/2019 Balance Grades as per ISO 1940
6/21
-
8/13/2019 Balance Grades as per ISO 1940
7/21
Balance Grades
A rotor balanced to G2.5 will vibrate at 2.5 mm/sec
(Velocity) if freely suspended while rotating at service
speed. (2.5 mm/sec = 0.10 IPS)
V(mm/sec) = 2pe(mm)*RPM
60sec/min
e(mm) = Residual Imbalance (g-mm)
Rotor weight(g)
-
8/13/2019 Balance Grades as per ISO 1940
8/21
Balance Grades
Balance Grade is a function of
Rotor Mass (lbm, Kg, g)
Service speed (rpm)
Residual imbalance (g-in, oz-in, lb-in, g-mm)
-
8/13/2019 Balance Grades as per ISO 1940
9/21
Initial Balance with Shop Balance Machine
It is difficult if not impossible to achieve Balance
Grades G1.0 or G0.4 in a balance machine only
-
8/13/2019 Balance Grades as per ISO 1940
10/21
Balance Grades G1.0 and G0.4 have special requirements.
G1.0
The rotor must be mounted in its own service bearings
No end drive (for balance machines)
G0.4
The rotor must be mounted in its own housing and bearings
Must be run under normal service conditions: Load,Temperature..
Self driven
-
8/13/2019 Balance Grades as per ISO 1940
11/21
Initial Balance with Shop Balance Machine : Roller Size
the roller diameter should differ from the journaldiameter by at least 10%, and the roller speed should
never differ less than 60 rpm from the journal speed. p.54 Fundamentals of Balancing, 2nd Ed. 03/1983; Schenk Trebel
-
8/13/2019 Balance Grades as per ISO 1940
12/21
Final Balance with Motor Assembled
Motor Setup
Flexible or Rigid Rotor Large 2-pole motors Effect of startup heating
Interference of 60 Hz electrical vibration on unloaded 2-
pole Motor phase readings
-
8/13/2019 Balance Grades as per ISO 1940
13/21
Motor Setup
Motor on Solid Base
Elevate on shims at base bolt locations Shim to eliminate soft foot
Secure with bolts or clamps
Lubricate bearings
Monitor vibration from the first start
Final Balance with Motor Assembled
-
8/13/2019 Balance Grades as per ISO 1940
14/21
Flexible or Rigid Rotor Large 2-pole motors
In test runs at service speed, moving two test
masses from the end planes to the center plane,
results in a vibration change of less than 20%.pp.21-22 Fundamentals of Balancing, 2nd Ed. 03/1983; Schenk Trebel
Graphic: http://www.schenck-usa.com/lib_101_types_unbal.asp
-
8/13/2019 Balance Grades as per ISO 1940
15/21
Effect of startup heating
-
8/13/2019 Balance Grades as per ISO 1940
16/21
60 Hz
-
8/13/2019 Balance Grades as per ISO 1940
17/21
Trial 1 (1:25 PM)
-
8/13/2019 Balance Grades as per ISO 1940
18/21
1X Vibration BC 2C CBPMmils pk-pk
5.
4.
3.
2.
1.
1.
2.
3.
4.
5.
5. 4. 3. 2. 1. 1. 2. 3. 4. 5.
Run1(ODE)Run2(ODE)
Run3(ODE)
Run4(ODE)
Run5(ODE)
Run6(ODE)
Run1(DE)
Run2(DE)
Run3(DE)
Run4(DE)
Run5(DE)
Run6(DE)
Trial 2, 3, 4, 5 6 (9:00 PM)
As low as reasonably
achievable.
-
8/13/2019 Balance Grades as per ISO 1940
19/21
Before and After MOV Spectrum
-
8/13/2019 Balance Grades as per ISO 1940
20/21
2 Year Overall Trend
-
8/13/2019 Balance Grades as per ISO 1940
21/21
Balance Grades:
Electric Motor Experience
Clay Boyd, PE
CBM Analyst
Questions?