axial piston pumps - parker€¦ · 4 parker hannifin pump & motor division europe chemnitz,...
TRANSCRIPT
Axial Piston PumpsSeries PVplus Variable Displacement
parker.com/pmde
3 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplusContents
Contents Page
Introduction and general Information ..............................................................4
Technical Data ................................................................................................5
Ordering Code ................................................................................................6
Pressure Controls .........................................................................................18
Remote Pressure Controls ...........................................................................20
Load Sensing Controls .................................................................................22
Horse Power/Torque Controls .......................................................................26
Performance Curves .....................................................................................30
Electronic P/Q Controls ................................................................................32
Efficiency and Case Drain Flows ..................................................................34
Performance Curves and Case Drain Flows PV 360 ....................................39
Accessories Control......................................................................................40
Proportional pressure relief valve PVACRE* ................................................42
Dimensions ...................................................................................................44
Pump Dimensions ........................................................................................56
Electronic Module PQDXXA .........................................................................60
Thru Drive, Mounting Kits .............................................................................61
Thru Drive, Flange Load Limitation ..............................................................62
Multiple Pump Combinations - Maximum Moment .......................................62
Through Drive, Shaft Load Limitations .........................................................63
4 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplus
With thru drive for single and multiple pumpsSwash plate type for open circuit
Introduction
Technical Features• Lownoiselevel• Fastresponse• Service-friendly• Highself-primingspeed• Compactdesign• Thrudrivefor100%nominaltorque
General InformationFluid recommendationsPremium quality hydraulic mineral fluid is recommended, like HLP oils to DIN 51524, part 2. Brugger- value recommended to be 30 N/mm2 minimum for general application and 50 N/mm2 for heavily loaded hydraulic equipment and fast cycling machines and/or high dynamic loads, measured in accordance with DIN 51 347-2. See also Document HY30-3248/UK Parker Hydraulic Fluids.
ViscosityThe normal operating viscosity should range between 16 and 100 mm2/s (cSt). Max. start-up viscosity is 1000 mm2/s (cSt).
FiltrationFor maximum pump and system component func-tionality and life, the system should be protected from contamination by effective filtration.Fluid cleanliness should be in accordance with ISO classification ISO 4406:1999. The quality of filter elements should be in accordance with ISO standards.General hydraulic systems for satisfactory operation: Class 20/18/15, according to ISO 4406:1999
Recommended cleanliness for maximum component life and functionality: Class 18/16/13, according to ISO 4406:1999
SealsCheck hydraulic fluid specification for chemical resistance of seal material.Check temperature range of seal material and compare with max. system and ambient temperature.
N – Nitrile (FKM shaft seal) -25…+90 °C V – FKM (FKM shaft seal) -25…+115 °C W – Nitrile (PTFE shaft seal) -30…+90 °C
Note: The highest fluid temperature will be at the drain port of the pump, up to 25 °C higher than in the reservoir.
5 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplusTechnical Data
PV063 PV080 PV092 PV140 PV180 PV270 PV360Frame size 3 3 3 4 4 5 6Max. Displacement [cm3/rev.] 63 80 92 140 180 270 360Output flow at 1500 rpm [l/min] 94.5 120 138 210 270 405 540Nominal pressure pN [bar] 350 350 350 350 350 350 350Min. outlet pressure [bar] 15 15 15 15 15 15 15Max.pressurepmaxat20%workingcycle1) [bar] 420 420 420 420 420 420 420Case drain pressure, continuous [bar] 0.5 0.5 0.5 0.5 0.5 0.5 0.5Case drain pressure, max. peak [bar] 2.0 2.0 2.0 2.0 2.0 2.0 2.0Min. Inlet pressure, abs. [bar] 0.8 0.8 0.8 0.8 0.8 0.8 0.8Max. Inlet pressure [bar] 16 16 16 16 16 16 16Input power at 1500 rpm and 350 bar [kW] 61.5 78 89.5 136 175 263 350Max speed at 1 bar, abs, inlet pressure [rpm] 2800 2500 2300 2400 2200 1800 1750Min. speed [rpm] 400 400 400 400 400 400 400Moment of inertia [kgm2] 0.018 0.018 0.018 0.030 0.030 0.098 0.103Weight [kg] 59 59 59 90 90 172 180
1) Check adjustment range each compensator.
PV016 PV020 PV023 PV028 PV032 PV040 PV046Frame size 1 1 1 1 2 2 2Max. Displacement [cm3/rev.] 16 20 23 28 32 40 46Output flow at 1500 rpm [l/min] 24 30 34,5 42 48 60 69Nominal pressure pN [bar] 350 350 350 350 350 350 350Min. outlet pressure [bar] 15 15 15 15 15 15 15Max.pressurepmaxat20%workingcycle1) [bar] 420 420 420 420 420 420 420Case drain pressure, continuous [bar] 0.5 0.5 0.5 0.5 0.5 0.5 0.5Case drain pressure, max. peak [bar] 2.0 2.0 2.0 2.0 2.0 2.0 2.0Min. Inlet pressure, abs. [bar] 0.8 0.8 0.8 0.8 0.8 0.8 0.8Max. Inlet pressure [bar] 16 16 16 16 16 16 16Input power at 1500 rpm and 350 bar [kW] 15.5 19.5 22.5 27.5 31 39 45Max speed at 1 bar, abs, inlet pressure [rpm] 3000 3000 3000 3000 2800 2800 2800Min. speed [rpm] 400 400 400 400 400 400 400Moment of inertia [kgm2] 0.0017 0.0017 0.0017 0.0017 0.0043 0.0043 0.0043Weight [kg] 19 19 19 19 30 30 30
6 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplusOrdering Code Frame Size 1
4) Drain, gage and flushing ports5) All mounting and connecting threads6) Mounting interface, code K and L only
axial piston pump
variable displacement
P Vmounting interface
1 K TR 1 1 Ncontrol
see next page
variation threadscode
coupling code
thru drivecode
size and
displacement
rotation seals
Code Displacement Size
016 16 cm³/rev 1020 20 cm³/rev 1023 23 cm³/rev 1028 28 cm³/rev 1
Code Coupling for thru drive as single part 7)
1 Single pump, no couplingH with coupling 25 x 1.5 x 15, DIN 5480 MK-PVBG1K01
Y with coupling SAE A 9T-16/32 DP MK-PVBG1K11
A with coupling SAE - 11T-16/32 DP MK-PVBG1K12
B with coupling SAE B 13T-16/32 DP MK-PVBG1K13
C with coupling SAE B-B 15T-16/32 DP MK-PVBG1K14
Code Thru drive option
No adaptor for 2nd pump
T Single pump prepared for thru drivewith adaptor for 2nd pump as single part 7)
A SAE A, Ø 82.55 mm MK-PVBG1Axx
B SAE B, Ø 101.6 mm MK-PVBG1Bxx
H metric, Ø 80 mm MK-PVBG1Hxx
J metric, Ø 100 mm MK-PVBG1Jxx
See dimensions for details7) to be ordered separately as single part see page 61.
Code Seals Shaft seal
N NBR FKMV FKM FKM
W NBR PTFE
Code Port4) Threads5)
1 BSPP metric3 UNF UNC
86) ISO 6149 metric
Code Mounting interface ShaftK metr. ISO
3019/24-hole flange Ø100 mm Cylindric, key
L 4-hole flange Ø100 mm Splined, DIN 5480D SAE
ISO 3019/1
4-hole flange SAE B Cylindric, key
E 4-hole flange SAE B-B Splined, SAE
Code Rotation 1)
R ClockwiseL Counter clockwise
1) When looked on shaft
Code Variation
1 Standard2 Electronic displacement sensor 2)
9 Special adjustment 3)
2) not for horse power control3) requires Kxxxx number
Standard pump is not painted. Black painted pump and ATEX (excludes electronic components) certification (Zone 2) is available as special option. For additional informations please contact Parker Hannifin.
7 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplusOrdering Code Frame Size 1
1) not for MT & *Z2) only for MT3) not for MT & MM
4) control variation Z and B without pressure pilot
5) further info in HY30-3254
Horse power / Torque controlCode
Nominal HP at 1.500 rpm
Nominal torque
B 3 kW 20 Nm
C 4 kW 25 Nm
D 5.5 kW 35 Nm
E 7.5 kW 50 Nm
G 11 kW 71 Nm
H 15 kW 97 Nm
K 18.5 kW 120 Nm
FunctionL Horse power control with pressure control 4)
C Horse power control with load sensing (single spool)
Z Horse power control with two spool LS control
Control variationC Standard version 1)
1 NG 6 interface top side
W With unloading function, 24 VDC solenoid
K Prop.-pilot valve type PVACRE...K35 mounted
Z Without integrated pilot valve, NG6 interface, for mounting of accessory code PVAC* 4)
B Without integrated pilot valve, without NG6 interface 4)
Code Control option
Electro hydraulic control 5)
F D V Proportional displacement control, no pressure compensation
U D Proportional displacement control, with pressure compensation
Control variation
R pilot operated pressure control, open NG6 interface
K pilot operated pressure control, proportional pilot valve type PVACRE...K35 mounted
M pilot operated pressure control, pressure sensor and proportional pilot valve type PVACRE...K35 mounted for pressure control and/or power control
Code Control options
0 0 1 No control
1 0 0 With cover plate, no control function (fixed displacement pump)
M M Standard pressure control, integrated pilot valve
M R Remote pressure control, integrated pilot valve
M F Load Sensing (flow) control, integrated pilot valve
M T Two spool LS control
Control variation
C Standard version 1)
1 NG6 interface top side for pilot valves
2 Remote pressure port int. supply , NG6 interface 2)
3 Remote pressure port ext. supply 2)
W With unloading function, 24VDC solenoid 1)
K Prop.-pilot valve type PVACRE...K35 mounted
Z Without integrated pilot valve, NG6 interface, for mounting of accessory code PVAC*
B Without integrated pilot valve, without NG6 interface 3)
P MT1 with mounted pilot valve PVAC1P 2)
8 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplusOrdering Code Frame Size 2
axial piston pump
variable displacement
P Vmounting interface
1 K TR 1 1 Ncontrol
see next page
variation threadscode
coupling code
thru drivecode
size and
displacement
rotation seals
4) Drain, gage and flushing ports5) All mounting and connecting threads6) Mounting interface, code K and L only
Code Displacement Size
032 32 cm³/rev 2040 40 cm³/rev 2046 46 cm³/rev 2
Code Rotation 1)
R ClockwiseL Counter clockwise
1) When looked on shaft
Code Mounting interface ShaftK metr. ISO
3019/24-hole flange Ø125 mm Cylindric, key
L 4-hole flange Ø125 mm Splined, DIN 5480D SAE
ISO 3019/1
4-hole flange SAE C Cylindric, key
E 4-hole flange SAE C Splined, SAE
Code Port4) Threads5)
1 BSPP metric3 UNF UNC
86) ISO 6149 metric
Code Variation
1 Standard2 Electronic displacement sensor 2)
9 Special adjustment 3)
2) not for horse power control3) requires Kxxxx number
Code Coupling for thru drive as single part 7)
1 Single pump, no couplingH with coupling 25 x 1.5 x 15, DIN 5480 MK-PVBG2K01
J with coupling 32 x 1.5 x 20, DIN 5480 MK-PVBG2K02
Y with coupling SAE A 9T-16/32 DP MK-PVBG2K11
A with coupling SAE - 11T-16/32 DP MK-PVBG2K12
B with coupling SAE B 13T-16/32 DP MK-PVBG2K13
C with coupling SAE B-B 15T-16/32 DP MK-PVBG2K14
D with coupling SAE C 14T-12/24 DP MK-PVBG2K15
Code Thru drive option
No adaptor for 2nd pump
T Single pump prepared for thru drivewith adaptor for 2nd pump as single part 6)
A SAE A, Ø 82.55 mm MK-PVBG2Axx
B SAE B, Ø 101.6 mm MK-PVBG2Bxx
C SAE C, Ø 127 mm MK-PVBG2Cxx
H metric, Ø 80 mm MK-PVBG2Hxx
J metric, Ø 100 mm MK-PVBG2Jxx
K metric, Ø 125 mm MK-PVBG2Kxx
See dimensions for details7) to be ordered separately as single part see page 61.
Code Seals Shaft seal
N NBR FKMV FKM FKM
W NBR PTFE
Standard pump is not painted. Black painted pump and ATEX certification (Zone 2) is available as special option. For additional informations please contact Parker Hannifin.
9 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplusOrdering Code Frame Size 2
1) not for MT & *Z2) only for MT3) not for MT & MM
Code Control options
0 0 1 No control
1 0 0 With cover plate, no control function (fixed displacement pump)
M M Standard pressure control, integrated pilot valve
M R Remote pressure control, integrated pilot valve
M F Load Sensing (flow) control, integrated pilot valve
M T Two spool LS control
Control variation
C Standard version 1)
1 NG6 interface top side for pilot valves
2 Remote pressure port int. supply , NG6 interface 2)
3 Remote pressure port ext. supply 2)
W With unloading function, 24VDC solenoid 1)
K Prop.-pilot valve type PVACRE...K35 mounted
Z Without integrated pilot valve, NG6 interface, for mounting of accessory code PVAC*
B Without integrated pilot valve, without NG6 interface 3)
P MT1 with mounted pilot valve PVAC1P 2)
Horse power / Torque controlCode
Nominal HP at 1.500 rpm
Nominal torque
D 5.5 kW 35 Nm
E 7.5 kW 50 Nm
G 11 kW 71 Nm
H 15 kW 97 Nm
K 18.5 kW 120 Nm
M 22 kW 142 Nm
S 30 kW 195 Nm
FunctionL Horse power control with pressure control 4)
C Horse power control with load sensing (single spool)
Z Horse power control with two spool LS control
Control variationC Standard version 1)
1 NG 6 interface top side
W With unloading function, 24 VDC solenoid
K Prop.-pilot valve type PVACRE...K35 mounted
Z Without integrated pilot valve, NG6 interface, for mounting of accessory code PVAC* 4)
B Without integrated pilot valve, without NG6 interface 4)
Code Control option
Electro hydraulic control 5)
F D V Proportional displacement control, no pressure compensation
U D Proportional displacement control, with pressure compensation
Control variation
R pilot operated pressure control, open NG6 interface
K pilot operated pressure control, proportional pilot valve type PVACRE...K35 mounted
M pilot operated pressure control, pressure sensor and proportional pilot valve type PVACRE...K35 mounted for pressure control and/or power control
4) control variation Z and B without pressure pilot
5) further info in HY30-3254
10 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplus
4) Drain, gage and flushing ports5) All mounting and connecting threads6) For PV063-PV092 only: pressure port 1 1/4" with 4 x M14 instead of 4 x M12
axial piston pump
variable displacement
highpressureversion
P Vmounting interface
1 K TR 1 1 Ncompensator
see next page
variation threadscode
coupling code
thru drivecode
size and
displacement
rotation seals
Ordering Code Frame Size 3
Code Displacement Size
063 63 cm³/rev 3080 80 cm³/rev 3092 92 cm³/rev 3
Code Rotation 1)
R ClockwiseL Counter clockwise
1) When looked on shaft
Code Mounting interface ShaftK metr. ISO
3019/24-hole flange Ø160 mm Cylindric, key
L 4-hole flange Ø160 mm Splined, DIN 5480D SAE
ISO 3019/1
4-hole flange SAE D Cylindric, key
E 4-hole flange SAE D Splined, SAE
Code Port4) Threads5)
1 BSPP metric3 UNF UNC
4 6) BSPP metr. M14
8 ISO 6149 metric
Code Coupling for thru drive as single part 7)
1 Single pump, no couplingH with coupling 25 x 1.5 x 15, DIN 5480 MK-PVBG3K01
J with coupling 32 x 1.5 x 20, DIN 5480 MK-PVBG3K02
K with coupling 40 x 1.5 x 25, DIN 5480 MK-PVBG3K03
Y with coupling SAE A 9T-16/32 DP MK-PVBG3K11
A with coupling SAE - 11T-16/32 DP MK-PVBG3K12
B with coupling SAE B 13T-16/32 DP MK-PVBG3K13
C with coupling SAE B-B 15T-16/32 DP MK-PVBG3K14
D with coupling SAE C 14T-12/24 DP MK-PVBG3K15
E with coupling SAE C-C 17T-12/24 DP MK-PVBG3K16
F with coupling SAE D, E 13T-8/16 DP MK-PVBG3K17
Code Thru drive option
No adaptor for 2nd pump
T Single pump prepared for thru drivewith adaptor for 2nd pump as single part 7)
A SAE A, Ø 82.55 mm MK-PVBG3Axx
B SAE B, Ø 101.6 mm MK-PVBG3Bxx
C SAE C, Ø 127 mm MK-PVBG3Cxx
D SAE D, Ø 152.4 mm MK-PVBG3Dxx
H metric, Ø 80 mm MK-PVBG3Hxx
J metric, Ø 100 mm MK-PVBG3Jxx
K metric, Ø 125 mm MK-PVBG3Kxx
L metric, Ø 160 mm MK-PVBG3Lxx
See dimensions for details7) to be ordered separately as single part see page 61.
Code Seals Shaft seal
N NBR FKMV FKM FKM
W NBR PTFE
Standard pump is not painted. Black painted pump and ATEX certification (Zone 2) is available as special option. For additional informations please contact Parker Hannifin.
Code Variation
1 Standard2 Electronic displacement sensor 2)
9 Special adjustment 3)
2) not for horse power control3) requires Kxxxx number
11 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplusOrdering Code Frame Size 3
1) not for MT & *Z2) only for MT3) not for MT & MM
Code Control options
0 0 1 No control
1 0 0 With cover plate, no control function (fixed displacement pump)
M M Standard pressure control, integrated pilot valve
M R Remote pressure control, integrated pilot valve
M F Load Sensing (flow) control, integrated pilot valve
M T Two spool LS control
Control variation
C Standard version 1)
1 NG6 interface top side for pilot valves
2 Remote pressure port int. supply , NG6 interface 2)
3 Remote pressure port ext. supply 2)
W With unloading function, 24VDC solenoid 1)
K Prop.-pilot valve type PVACRE...K35 mounted
Z Without integrated pilot valve, NG6 interface, for mounting of accessory code PVAC*
B Without integrated pilot valve, without NG6 interface 3)
P MT1 with mounted pilot valve PVAC1P 2)
Horse power / Torque controlCode
Nominal HP at 1.500 rpm
Nominal torque
G 11 kW 71 Nm
H 15 kW 97 Nm
K 18.5 kW 120 Nm
M 22 kW 142 Nm
S 30 kW 195 Nm
T 37 kW 240 Nm
U 45 kW 290 Nm
W 55 kW 355 Nm
FunctionL Horse power control with pressure control 4)
C Horse power control with load sensing (single spool)
Z Horse power control with two spool LS control
Control variationC Standard version 1)
1 NG 6 interface top side
W With unloading function, 24 VDC solenoid
K Prop.-pilot valve type PVACRE...K35 mounted
Z Without integrated pilot valve, NG6 interface, for mounting of accessory code PVAC* 4)
B Without integrated pilot valve, without NG6 interface 4)
Code Control option
Electro hydraulic control 5)
F D V Proportional displacement control, no pressure compensation
U D Proportional displacement control, with pressure compensation
Control variation
R pilot operated pressure control, open NG6 interface
K pilot operated pressure control, proportional pilot valve type PVACRE...K35 mounted
M pilot operated pressure control, pressure sensor and proportional pilot valve type PVACRE...K35 mounted for pressure control and/or power control
4) control variation Z and B without pressure pilot
5) further info in HY30-3254
12 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplusOrdering Code Frame Size 4
4) Drain, gage and flushing ports5) All mounting and connecting threads6) Pressure port 1 1/4" with 4 x M14 instead of 4 x M127) Mounting interface, code K and L only
axial piston pump
variable displacement
P Vmounting interface
1 K TR 1 1 Ncontrol
see next page
variation threadscode
coupling code
thru drivecode
size and
displacement
rotation seals
Code Displacement Size
140 140 cm³/rev 4180 180 cm³/rev 4
Code Rotation 1)
R ClockwiseL Counter clockwise
1) When looked on shaft
Code Mounting interface ShaftK metr. ISO
3019/24-hole flange Ø160 mm Cylindric, key
L 4-hole flange Ø160 mm Splined, DIN 5480D
SAE ISO
3019/1
4-hole flange SAE D Cylindric, key, SAE F
E 4-hole flange SAE D Splined, SAE F, SAE D
F 4-hole flange SAE D Cylindric, key, SAE D
G 4-hole flange SAE D Splined, SAE D
Code Port4) Threads5)
1 BSPP metric3 UNF UNC
4 6) BSPP metr. M14
8 7) ISO 6149 metric
Code Coupling for thru drive as single part 8)
1 Single pump, no couplingH with coupling 25 x 1.5 x 15, DIN 5480 MK-PVBG4K01
J with coupling 32 x 1.5 x 20, DIN 5480 MK-PVBG4K02
K with coupling 40 x 1.5 x 25, DIN 5480 MK-PVBG4K03
L with coupling 50 x 2 x 24, DIN 5480 MK-PVBG4K04
Y with coupling SAE A 9T-16/32 DP MK-PVBG4K11
A with coupling SAE - 11T-16/32 DP MK-PVBG4K12
B with coupling SAE B 13T-16/32 DP MK-PVBG4K13
C with coupling SAE B-B 15T-16/32 DP MK-PVBG4K14
D with coupling SAE C 14T-12/24 DP MK-PVBG4K15
E with coupling SAE C-C 17T-12/24 DP MK-PVBG4K16
F with coupling SAE D, E 13T-8/16 DP MK-PVBG4K17
G with coupling SAE F 15T-8/16 DP MK-PVBG4K18
Code Thru drive option
No adaptor for 2nd pump
T Single pump prepared for thru drivewith adaptor for 2nd pump as single part 8)
A SAE A, Ø 82.55 mm MK-PVBG4Axx
B SAE B, Ø 101.6 mm MK-PVBG4Bxx
C SAE C, Ø 127 mm MK-PVBG4Cxx
D SAE D, Ø 152.4 mm MK-PVBG4Dxx
H metric, Ø 80 mm MK-PVBG4Hxx
J metric, Ø 100 mm MK-PVBG4Jxx
K metric, Ø 125 mm MK-PVBG4Kxx
L metric, Ø 160 mm MK-PVBG4Lxx
See dimensions for details8) to be ordered separately as single part see page 61.
Code Seals Shaft seal
N NBR FKMV FKM FKM
W NBR PTFE
Standard pump is not painted. Black painted pump and ATEX certification (Zone 2) is available as special option. For additional informations please contact Parker Hannifin.
Code Variation
1 Standard2 Electronic displacement sensor 2)
9 Special adjustment 3)
2) not for horse power control3) requires Kxxxx number
13 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplusOrdering Code Frame Size 4
1) not for MT & *Z2) only for MT3) not for MT & MM
Code Control options
0 0 1 No control
1 0 0 With cover plate, no control function (fixed displacement pump)
M M Standard pressure control, integrated pilot valve
M R Remote pressure control, integrated pilot valve
M F Load Sensing (flow) control, integrated pilot valve
M T Two spool LS control
Control variation
C Standard version 1)
1 NG6 interface top side for pilot valves
2 Remote pressure port int. supply , NG6 interface 2)
3 Remote pressure port ext. supply 2)
W With unloading function, 24VDC solenoid 1)
K Prop.-pilot valve type PVACRE...K35 mounted
Z Without integrated pilot valve, NG6 interface, for mounting of accessory code PVAC*
B Without integrated pilot valve, without NG6 interface 3)
P MT1 with mounted pilot valve PVAC1P 2)
Horse power / Torque controlCode
Nominal HP at 1.500 rpm
Nominal torque
K 18.5 kW 120 Nm
M 22 kW 142 Nm
S 30 kW 195 Nm
T 37 kW 240 Nm
U 45 kW 290 Nm
W 55 kW 355 Nm
Y 75 kW 485 Nm
Z 90 kW 585 Nm
2 110 kW 700 Nm
FunctionL Horse power control with pressure control 4)
C Horse power control with load sensing (single spool)
Z Horse power control with two spool LS control
Control variationC Standard version 1)
1 NG 6 interface top side
W With unloading function, 24 VDC solenoid
K Prop.-pilot valve type PVACRE...K35 mounted
Z Without integrated pilot valve, NG6 interface, for mounting of accessory code PVAC* 4)
B Without integrated pilot valve, without NG6 interface 4)
Code Control option
Electro hydraulic control 5)
F D V Proportional displacement control, no pressure compensation
U D Proportional displacement control, with pressure compensation
Control variation
R pilot operated pressure control, open NG6 interface
K pilot operated pressure control, proportional pilot valve type PVACRE...K35 mounted
M pilot operated pressure control, pressure sensor and proportional pilot valve type PVACRE...K35 mounted for pressure control and/or power control
4) control variation Z and B without pressure pilot
5) further info in HY30-3254
14 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplus
4) Drain, gage and flushing ports5) All mounting and connecting threads
axial piston pump
variable displacement
highpressureversion
P Vmounting interface
1 K TR 1 1 Ncompensator
see next page
variation threadscode
coupling code
thru drivecode
size and
displacement
rotation seals
Ordering Code Frame Size 5
Code Displacement Size
270 270 cm³/rev 5
Code Rotation 1)
R ClockwiseL Counter clockwise
1) When looked on shaft
Code Mounting interface ShaftK metr. ISO
3019/24-hole flange Ø200 mm Cylindric, key
L 4-hole flange Ø200 mm Splined, DIN 5480D SAE
ISO 3019/1
4-hole flange SAE E Cylindric, key
E 4-hole flange SAE E Splined, SAE
Code Port4) Threads5)
1 BSPP metric3 UNF UNC
8 ISO 6149 metric
Code Coupling for thru drive as single part 6)
1 Single pump, no couplingH with coupling 25 x 1.5 x 15, DIN 5480 MK-PVBG5K01
J with coupling 32 x 1.5 x 20, DIN 5480 MK-PVBG5K02
K with coupling 40 x 1.5 x 25, DIN 5480 MK-PVBG5K03
L with coupling 50 x 2 x 24, DIN 5480 MK-PVBG5K04
M with coupling 60 x 2 x 28, DIN 5480 MK-PVBG5K05
Y with coupling SAE A 9T-16/32 DP MK-PVBG5K11
A with coupling SAE - 11T-16/32 DP MK-PVBG5K12
B with coupling SAE B 13T-16/32 DP MK-PVBG5K13
C with coupling SAE B-B 15T-16/32 DP MK-PVBG5K14
D with coupling SAE C 14T-12/24 DP MK-PVBG5K15
E with coupling SAE C-C 17T-12/24 DP MK-PVBG5K16
F with coupling SAE D, E 13T-8/16 DP MK-PVBG5K17
G with coupling SAE F 15T-8/16 DP MK-PVBG5K18
Code Thru drive option
No adaptor for 2nd pump
T Single pump prepared for thru drivewith adaptor for 2nd pump as single part 6)
A SAE A, Ø 82.55 mm MK-PVBG5Axx
B SAE B, Ø 101.6 mm MK-PVBG5Bxx
C SAE C, Ø 127 mm MK-PVBG5Cxx
D SAE D, Ø 152.4 mm MK-PVBG5Dxx
E SAE E, Ø 165.1 mm MK-PVBG5Exx
H metric, Ø 80 mm MK-PVBG5Hxx
J metric, Ø 100 mm MK-PVBG5Jxx
K metric, Ø 125 mm MK-PVBG5Kxx
L metric, Ø 160 mm MK-PVBG5Lxx
M metric, Ø 200 mm MK-PVBG5Mxx
See dimensions for details6) to be ordered separately as single part see page 61.
Code Seals Shaft seal
N NBR FKMV FKM FKM
W NBR PTFE
Standard pump is not painted. Black painted pump and ATEX certification (Zone 2) is available as special option. For additional informations please contact Parker Hannifin.
Code Variation
1 Standard2 Electronic displacement sensor 2)
9 Special adjustment 3)
2) not for horse power control3) requires Kxxxx number
15 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplusOrdering Code Frame Size 5
1) not for MT & *Z2) only for MT3) not for MT & MM
Code Control options
0 0 1 No control
1 0 0 With cover plate, no control function (fixed displacement pump)
M M Standard pressure control, integrated pilot valve
M R Remote pressure control, integrated pilot valve
M F Load Sensing (flow) control, integrated pilot valve
M T Two spool LS control
Control variation
C Standard version 1)
1 NG6 interface top side for pilot valves
2 Remote pressure port int. supply , NG6 interface 2)
3 Remote pressure port ext. supply 2)
W With unloading function, 24VDC solenoid 1)
K Prop.-pilot valve type PVACRE...K35 mounted
Z Without integrated pilot valve, NG6 interface, for mounting of accessory code PVAC*
B Without integrated pilot valve, without NG6 interface 3)
P MT1 with mounted pilot valve PVAC1P 2)
Horse power / Torque controlCode
Nominal HP at 1.500 rpm
Nominal torque
T 37 kW 240 Nm
U 45 kW 290 Nm
W 55 kW 350 Nm
Y 75 kW 480 Nm
Z 90 kW 580 Nm
2 110 kW 700 Nm
3 132 kW 840 Nm
FunctionL Horse power control with pressure control 4)
C Horse power control with load sensing (single spool)
Z Horse power control with two spool LS control
Control variationC Standard version 1)
1 NG 6 interface top side
W With unloading function, 24 VDC solenoid
K Prop.-pilot valve type PVACRE...K35 mounted
Z Without integrated pilot valve, NG6 interface, for mounting of accessory code PVAC* 4)
B Without integrated pilot valve, without NG6 interface 4)
Code Control option
Electro hydraulic control 5)
F D V Proportional displacement control, no pressure compensation
U D Proportional displacement control, with pressure compensation
Control variation
R pilot operated pressure control, open NG6 interface
K pilot operated pressure control, proportional pilot valve type PVACRE...K35 mounted
M pilot operated pressure control, pressure sensor and proportional pilot valve type PVACRE...K35 mounted for pressure control and/or power control
4) control variation Z and B without pressure pilot
5) further info in HY30-3254
16 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplusOrdering Code Frame Size 6
4) Drain, gage and flushing ports5) All mounting and connecting threads
axial piston pump
variable displacement
P Vmounting interface
1 K TR 1 1 Ncontrol
see next page
variation threadscode
coupling code
thru drivecode
size and
displacement
rotation seals
Code Displacement Size
360 360 cm³/rev 6
Code Rotation 1)
R ClockwiseL Counter clockwise
1) When looked on shaft
Code Mounting interface ShaftK
metr. ISO3019/2
4-hole flange Ø250 mm Cylindric, keyL 4-hole flange Ø250 mm Splined, DIN 5480R 4-hole flange Ø224 mm Cylindric, keyT 4-hole flange Ø224 mm Splined, DIN 5480D SAE
ISO 3019/1
4-hole flange SAE E Cylindric, key
E 4-hole flange SAE E Splined, DIN 5480
Code Port4) Threads5)
1 BSPP metric3 UNF UNC
Code Coupling for thru drive as single part 6)
1 Single pump, no couplingH with coupling 25 x 1.5 x 15, DIN 5480 MK-PVBG5K01
J with coupling 32 x 1.5 x 20, DIN 5480 MK-PVBG5K02
K with coupling 40 x 1.5 x 25, DIN 5480 MK-PVBG5K03
L with coupling 50 x 2 x 24, DIN 5480 MK-PVBG5K04
M with coupling 60 x 2 x 28, DIN 5480 MK-PVBG5K05
P with coupling 70 x 3 x 22, DIN 5480 MK-PVBG5K06
Y with coupling SAE A 9T-16/32 DP MK-PVBG5K11
A with coupling SAE - 11T-16/32 DP MK-PVBG5K12
B with coupling SAE B 13T-16/32 DP MK-PVBG5K13
C with coupling SAE B-B 15T-16/32 DP MK-PVBG5K14
D with coupling SAE C 14T-12/24 DP MK-PVBG5K15
E with coupling SAE C-C 17T-12/24 DP MK-PVBG5K16
F with coupling SAE D, E 13T-8/16 DP MK-PVBG5K17
G with coupling SAE F 15T-8/16 DP MK-PVBG5K18
Code Thru drive option
No adaptor for 2nd pump
T Single pump prepared for thru drivewith adaptor for 2nd pump as single part 6)
A SAE A, Ø 82.55 mm MK-PVBG5Axx
B SAE B, Ø 101.6 mm MK-PVBG5Bxx
C SAE C, Ø 127 mm MK-PVBG5Cxx
D SAE D, Ø 152.4 mm MK-PVBG5Dxx
E SAE E, Ø 165.1 mm MK-PVBG5Exx
H metric, Ø 80 mm MK-PVBG5Hxx
J metric, Ø 100 mm MK-PVBG5Jxx
K metric, Ø 125 mm MK-PVBG5Kxx
L metric, Ø 160 mm MK-PVBG5Lxx
M metric, Ø 200 mm MK-PVBG5Mxx
See dimensions for details6) to be ordered separately as single part see page 61.
Code Seals Shaft seal
N NBR FKMV FKM FKM
Standard pump is not painted. Black painted pump and ATEX certification (Zone 2) is available as special option. For additional informations please contact Parker Hannifin.
Code Variation
1 Standard2 Electronic displacement sensor 2)
9 Special adjustment 3)
2) not for horse power control3) requires Kxxxx number
17 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplusOrdering Code Frame Size 6
1) not for MT & *Z2) only for MT3) not for MT & MM
Code Control options
0 0 1 No control
1 0 0 With cover plate, no control function (fixed displacement pump)
M M Standard pressure control, integrated pilot valve
M R Remote pressure control, integrated pilot valve
M F Load Sensing (flow) control, integrated pilot valve
M T Two spool LS control
Control variation
C Standard version 1)
1 NG6 interface top side for pilot valves
2 Remote pressure port int. supply , NG6 interface 2)
3 Remote pressure port ext. supply 2)
W With unloading function, 24VDC solenoid 1)
K Prop.-pilot valve type PVACRE...K35 mounted
Z Without integrated pilot valve, NG6 interface, for mounting of accessory code PVAC*
B Without integrated pilot valve, without NG6 interface 3)
P MT1 with mounted pilot valve PVAC1P 2)
Horse power / Torque controlCode
Nominal HP at 1.500 rpm
Nominal torque
U 45 kW 290 Nm
W 55 kW 350 Nm
Y 75 kW 480 Nm
Z 90 kW 580 Nm
2 110 kW 700 Nm
3 132 kW 840 Nm
4 160 kW 1020 Nm
5 180 kW 1150 Nm
6 200 kW 1280 Nm
FunctionL Horse power control with pressure control 4)
C Horse power control with load sensing (single spool)
Z Horse power control with two spool LS control
Control variationC Standard version 1)
1 NG 6 interface top side
W With unloading function, 24 VDC solenoid
K Prop.-pilot valve type PVACRE...K35 mounted
Z Without integrated pilot valve, NG6 interface, for mounting of accessory code PVAC* 4)
B Without integrated pilot valve, without NG6 interface 4)
Code Control option
Electro hydraulic control 5)
F D V Proportional displacement control, no pressure compensation
U D Proportional displacement control, with pressure compensation
Control variation
R pilot operated pressure control, open NG6 interface
K pilot operated pressure control, proportional pilot valve type PVACRE...K35 mounted
M pilot operated pressure control, pressure sensor and proportional pilot valve type PVACRE...K35 mounted for pressure control and/or power control
4) control variation Z and B without pressure pilot
5) further info in HY30-3254
18 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplus
S T
MP1 PAP T
P A T
BV BD
Standard Pressure ControlControl option MMCThe standard pressure control adjusts the pump displacement according to the actual need of flow in the system in order to keep the pressure constant.
Control schematics
Response times of the pump are collected from a circuit as below by measuring the pumps swash angle movement at different pressures.
Dynamic characteristic of flow control *
t on stroke tde-stroke
Dis
plac
emen
t [%
]
0
25
50
75
100
Response time
Pressure Controls
Time on-stroke [ms] Time de-stroke [ms]
against50 bar
against350 bar
zero stroke50 bar
zero stroke350 bar
PV360 520 180 120 82
Pressure adjustment range 15 to 420 bar
Factory setting pressure 50 bar
Differential pressure adjustment range 10 to 40 bar
Factory setting differential pressure 15 bar
Control oil consumption Max 8.0 l/min
Typically pilot flow approx 1,5 l/min
* Curve shown exaggerated
On/Off valve
19 Parker Hannifi nPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplus
S T
MP1 PAP T
P A TT
PBV BD
S T
MP1 PAP T
P A T
T
PBV BD
S T
MP1 PAP T
P A T
T
PBV BD
S T
MP1 PAP T
P A TT
PBV BD
Pressure Controls
Control option MM1With code MM1 the standard pressure control has a valve interface size NG 6 DIN 24340 (CETOP 03 acc. RP35H, NFPA D03) on the top side.
This interface allows the mounting of accessories like multiple pressure selectors without the need of external piping and valve mounting.
Standard Pressure Control with NG6 Interface
Standard Pressure Control with Electrical UnloadingControl option MMWWith code MMW a solenoid operated directional control valve (D1VW002KNJW) for electrical unloading is mounted on the control top side.
When the solenoid is de-energised, the pump compen-sates at a stand-by pressure of typically 15 bar. When the solenoid is energised, the pump compensates at the pressure adjusted on the integrated pilot valve.
Standard Pressure Control with Proportional Pilot ValveControl option MMKWith code MMK a proportional pilot valve of type PVACRE..35 (see page 43) is mounted on the top side interface.
This allows a variation of the pump compensating pres-sure between 20 and 350 bar by an electrical signal.
Control option MMZControl MMZ has no integrated pilot valve but a valve interface NG6 DIN 24340 on the top.
This version is recommended for valve accessories.
For operation at >350 bar please select respective valve accessories (see page 40)
Standard Pressure Control without Integrated Pressure Pilot Valve
20 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplus
S T
MP1 PAP T
P A T
PR
BV BD
Remote Pressure ControlControl option MRCThe remote pressure control adjusts the pump displacement according to the actual need of flow in the system in order to keep the pressure constant at a level given by a remotely installed pilot valve.
Control schematics
Response times of the pump are collected from a circuit as below by measuring the pumps swash angle movement at different pressures.
Dynamic characteristic of flow control *
Remote Pressure Controls
Pressure adjustment range 15 to 420 bar
Factory setting pressure 50 bar
Differential pressure adjustment range 10 to 40 bar
Factory setting differential pressure 15 bar
Control oil consumption Max 8.0 l/min
Typically pilot flow approx 1,5 l/min
* Curve shown exaggerated
t on stroke tde-stroke
Dis
plac
emen
t [%
]
0
25
50
75
100
Response timeTime on-stroke [ms] Time de-stroke [ms]
against50 bar
against350 bar
zero stroke50 bar
zero stroke350 bar
PV360 520 180 120 82
On/Off valve
21 Parker Hannifi nPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplus
S T
MP1 PAP T
P A T
PR
T
PBV BD
S T
MP1 PAP T
P A T
PR
T
PBV BD
S T
MP1 PAP T
P A T
PR
T
PBV BD
Remote Pressure Controls
Control option MR1With code MR1 the remote pressure control has a valve interface size NG 6 DIN 24340 (CETOP 03 acc. RP35H, NFPA D03) on the top side.
This interface allows the mounting of accessories like multiple pressure selectors without the need of external piping and valve mounting.
Remote Pressure Control with NG6 Interface
Remote Pressure Control with Electrical UnloadingControl option MRWWith code MRW a solenoid operated directional control valve (D1VW002KNJW) for electrical unloading is mounted on the control top side.
When the solenoid is de-energised, the pump compen-sates at a stand-by pressure of typically 15 bar. When the solenoid is energised, the pump compensates at the pressure adjusted on the integrated pilot valve.
Remote Pressure Control with Proportional Pilot ValveControl option MRKWith code MRK a proportional pilot valve of type PVACRE..35 (see page 43) is mounted on the top side interface.
This allows a variation of the pump compensating pres-sure between 20 and 350 bar by an electrical signal.
Control option MRZControl MRZ has no integrated pilot valve but a NG6 DIN 24340 interface topside.
Remote Pressure Control without Integrated Pressure Pilot Valve
S T
MP1 PAP T
P A T
PR
BV BD
S T
MP1 PAP T
P A T
PR
T
PBV BD
This version is recommended for valve accessories.
Control option MRBControl MRB has no integrated pilot valve.
22 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplus
Load Sensing ControlControl option MFCThe pilot pressure of the load sensing control is taken from a load sensing port in the hydraulic system. It is used to match pump flow to system demands. Integrated pilot valve allows pmax adjustment.
Control schematics
Response times of the pump are collected from a circuit as below by measuring the pumps swash angle movement at different pressures.
Dynamic characteristic of flow control *
Load Sensing Controls
Time on-stroke [ms] Time de-stroke [ms]
stand-byto 50 bar
stand-byto 350 bar
50 bar tostand-by
350 bar tostand-by
PV360 500 690 830 50
Pressure adjustment range 15 to 420 bar
Factory setting pressure 50 bar
Differential pressure adjustment range 10 to 40 bar
Factory setting differential pressure 10 bar
Control oil consumption Max 8.0 l/min
Typically pilot flow approx 1,5 l/min
* Curve shown exaggerated
t on stroke tde-stroke
Dis
plac
emen
t [%
]
0
25
50
75
100
Response time
Load valve
S T
MP1 PAP T
P A T
PF
BD
BV
23 Parker Hannifi nPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplus
S T
MP1 PAP T
P A T
PF
T
P
BV
BD
S T
MP1 PAP T
P A T
PF
T
P
BV
BD
S T
MP1 PAP T
P A T
PF
T
P
BV
BD
Load Sensing Controls
Control option MF1With code MF1 the remote pressure control has a valve interface size NG 6 DIN 24340 (CETOP 03 acc. RP35H, NFPA D03) on the top side.
This interface allows the mounting of accessories like multiple pressure selectors without the need of external piping and valve mounting.
Load Sensing Control with NG6 Interface
Load Sensing Control with Electrical UnloadingControl option MFWWith code MFW a solenoid operated directional control valve (D1VW002KNJW) for electrical unloading is mounted on the control top side.
When the solenoid is de-energised, the pump compen-sates at a stand-by pressure of typically 15 bar. When the solenoid is energised, the pump compensates at the pressure adjusted on the integrated pilot valve.
Load Sensing Control with Proportional Pilot ValveControl option MFKWith code MFK a proportional pilot valve of type PVACRE..35 (see page 43) is mounted on the top side interface.
This allows a variation of the pump compensating pres-sure between 20 and 350 bar by an electrical signal.
Control option MFZControl MFZ has no integrated pilot valve but a NG6 DIN 24340 interface topside.
Load Sensing Control without Integrated Pressure Pilot Valve
S T
MP1 PAP T
P A T
PF
BD
S T
MP1 PAP T
P A T
PF
T
P
BV
BD
This version is recommended for valve accessories.
Control option MFBControl MFB has no integrated pilot valve.
24 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplus
2 Spool Load Sensing ControlControl option MTPThe pilot pressure of the load sensing control is taken from a load sensing port in the hydraulic system. It is used to match pump flow to system demands. With the 2 spool control the interaction of the two control functions is avoided by using two separate control valves for flow and pressure compensation.
Control schematics
Response times of the pump are collected from a circuit as below by measuring the pumps swash angle movement at different pressures.
Dynamic characteristic of flow control *
Load Sensing Controls
Time on-stroke [ms] Time de-stroke [ms]
stand-byto 50 bar
stand-byto 350 bar
50 bar tostand-by
350 bar tostand-by
PV360 920 670 1000 170
Pressure adjustment range 15 to 420 bar
Factory setting pressure 50 bar
Differential pressure adjustment range 10 to 40 bar
Factory setting differential pressure load sensing
10 bar
Factory setting differential pressure, pressure control
15 bar
Control oil consumption Max 8.0 l/min
Typically pilot flow approx 1,5 l/min
* Curve shown exaggerated
t on stroke tde-stroke
Dis
plac
emen
t [%
]
0
25
50
75
100
Response time
p
Q
Load valve
S T
MP1 PAP T
P A T
PF
P
T
WV
BVBD1
BD2
25 Parker Hannifi nPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplus
S T
MP1 PAP T
P A T
PF
P
T
WV
BVBD1
BD2
S T
MP1 PAP T
P A T
PF
P
T
WV
BVBD1
BD2
Load Sensing Controls
Control option MT1 & MTZControl MT1 & MTZ has no integrated pressure pilot valve but NG 6 DIN 24340 (CETOP 03 acc. RP35H, NFPA D03) on the top side.
This interface allows the mounting of accessories like multiple pressure selectors without the need of external piping and valve mounting.
2 Spool Load Sensing Control with NG6 Interface without Integrated Pressure Pilot Valve
2 Spool Load Sensing Control with Propor-tional Pilot ValveControl option MTKWith code MTK a proportional pilot valve of type PVACRE..35 (see page 43) is mounted on the top side interface.
This allows a variation of the pump compensating pres-sure between 20 and 350 bar by an electrical signal.
Control option MT2Control MT2 has a valve interface NG6 DIN 24340 on the top side and remote pressure port internal supply.
2 Spool Load Sensing Control without Integrated Pressure Pilot Valve
S T
MP1 PAP T
P A T
PF
P
T
WV
PR
BVBD1
BD2
S T
MP1 PAP T
P A T
PF
P
T
WV
PR
BD1
BD2
2 Spool Load Sensing Control without Integrated Pressure Pilot ValveControl option MT3Control MT3 with pressure remote port external supply.
26 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplus
S T
MP1 PAP T
P A T
L
L
BDBV
Horse Power/Torque Controls with Pressure ControlControl option *LCThe horse power control type *L* provides the benefit of the pressure control, plus the ability to limit the input power the pump will draw. These controls are beneficial when the power available from the prime mover for the hydraulics is limited or the application power demand has both high flow/low pressure and low flow/high pressure duty cycles.
Control schematics
Response times of the pump are collected from a circuit as below by measuring the pumps swash angle movement at different pressures.
Dynamic characteristic of flow control *
Horse Power/Torque Controls
See Horse Power characteristic curves on page 30Pressure adjustment range 15 to 350 bar
Factory setting pressure 350 bar
Differential pressure adjustment range 10 to 40 bar
Factory setting differential pressure 15 bar
Control oil consumption Max 8.0 l/min
Typically pilot flow approx 1,5 l/min
* Curve shown exaggerated
t on stroke tde-stroke
Dis
plac
emen
t [%
]
0
25
50
75
100
Response time
Time on-stroke [ms] Time de-stroke [ms]
against50 bar
against350 bar
zero stroke50 bar
zero stroke350 bar
PV360 90 90 100 100
Load valve
27 Parker Hannifi nPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplus
S T
MP1 PAP T
P A T
L
L
P
TBDBV
S T
MP1 PAP T
P A T
L
L
P
TBDBV
S T
MP1 PAP T
P A T
L
L
P
TBDBV
Horse Power/Torque Controls
Control option *L1With code *L1 the horse power control has a valve interface size NG 6 DIN 24340 (CETOP 03 acc. RP35H, NFPA D03) on the top side.
This interface allows the mounting of accessories like multiple pressure selectors without the need of external piping and valve mounting.
Horse Power/Torque Control with NG6 Interface
Horse Power/Torque Control with Electrical UnloadingControl option *LWWith code *LW a solenoid operated directional control valve (D1VW002KNJW) for electrical unloading is mounted on the control top side.
When the solenoid is de-energised, the pump compen-sates at a stand-by pressure of typically 15 bar. When the solenoid is energised, the pump compensates at the pressure adjusted on the integrated pilot valve.
Horse Power/Torque Control with Proportional Pilot ValveControl option *LKWith code *LK a proportional pilot valve of type PVACRE..35 (see page 43) is mounted on the top side interface.
This allows a variation of the pump compensating pres-sure between 20 and 350 bar by an electrical signal.
Control option *LZControl *LZ has no integrated pilot valve but a NG6 DIN 24340 interface topside.
Horse Power/Torque Control without Integrated Pressure Pilot Valve
S T
MP1 PAP T
P A T
L
L
PR
BDBV
S T
MP1 PAP T
P A T
L
L
P
TBDBV
This version is recommended for valve accessories.
Control option *LBControl *LB has no integrated pilot valve.
28 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplus
Horse Power/Torque Controls with Load SensingControl option *CCThe horse power control type *C* provides the benefit of the load sensing control, plus the ability to limit the input power the pump will draw. These controls are beneficial when the power available from the prime mover for the hydraulics is limited or the application power demand has both high flow/low pressure and low flow/high pressure duty cycles.
Control schematics
Response times of the pump are collected from a circuit as below by measuring the pumps swash angle movement at different pressures.
Dynamic characteristic of flow control *
Horse Power/Torque Controls
See Horse Power characteristic curves on page 30
Time on-stroke [ms] Time de-stroke [ms]
stand-byto 50 bar
stand-byto 350 bar
50 bar tostand-by
350 bar tostand-by
PV360 90 90 100 100
Pressure adjustment range 15 to 350 bar
Factory setting pressure 350 bar
Differential pressure adjustment range 10 to 40 bar
Factory setting differential pressure 15 bar
Control oil consumption Max 8.0 l/min
Typically pilot flow approx 1,5 l/min
* Curve shown exaggerated
t on stroke tde-stroke
Dis
plac
emen
t [%
]
0
25
50
75
100
Response time
Load valve
S T
MP1 PAP T
P A T
L
L
PF
BD
BV
29 Parker Hannifi nPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplus
S T
MP1 PAP T
P A T
L
L
P
T
PF
BD
BV
S T
MP1 PAP T
P A T
L
L
P
T
PF
BD
BV
S T
MP1 PAP T
P A T
L
L
P
T
PF
BD
BV
S T
MP1 PAP T
P A T
L
L
P
T
PF
BD
BV
Horse Power/Torque Controls
Control option *C1With code *C1 the horse power control has a valve interface size NG 6 DIN 24340 (CETOP 03 acc. RP35H, NFPA D03) on the top side.
This interface allows the mounting of accessories like multiple pressure selectors without the need of external piping and valve mounting.
Horse Power/Torque Control with Load Sensing & NG6 Interface
Horse Power/Torque Control with Load Sensing & Electrical UnloadingControl option *CWWith code *CW a solenoid operated directional control valve (D1VW002KNJW) for electrical unloading is mounted on the control top side.
When the solenoid is de-energised, the pump compen-sates at a stand-by pressure of typically 15 bar. When the solenoid is energised, the pump compensates at the pressure adjusted on the integrated pilot valve.
Horse Power/Torque Control with Load Sensing & Proportional ValveControl option *CKWith code *CK a proportional pilot valve of type PVACRE..35 (see page 43) is mounted on the top side interface.
This allows a variation of the pump compensating pres-sure between 20 and 350 bar by an electrical signal.
Control option *CZ
Control *CZ has no integrated pilot valve but NG6 DIN 24340 interface topside.
Horse Power/Torque Control with Load Sensing without Integrated Pilot Valve
S T
MP1 PAP T
P A T
L
L
PF
BD
BV
Control option *CBControl *CB has no integrated pilot valve.
30 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplus
Typical Horse Power/Torque Control Characteristics
Performance Curves
200210
180
160
140
120
100
80
60
40
20
00 50 100 150 200 250 300 350
PV140
W=55 kWT=37 kWS=30 kWM=22 kW
K=18,5 kW
Y=75 kW
U=45 kW
Z=90 kW
Flo
w r
ate
Q [l
/min
]
Flo
w r
ate
Q [l
/min
]
Flo
w r
ate
Q [l
/min
]
Pressure p [bar]
Pressure p [bar] Pressure p [bar]
Flo
w r
ate
Q [l
/min
]
Pressure p [bar]
140
120
100
80
60
40
20
00 50 100 150 200 250 300 350
PV092PV080PV063
S=30 kWM=22 kWK=18,5 kWG=11 kW
H=15 kW
T=37 kW
W=55 kWU=45kW
K=18.5 kW
10
35
45
0
5
15
20
30
40
25
0 100 30050 150 250200 350
PV023PV028
PV020PV016
K=18.5 kW
C=4 kW
D=5.5 kW
H=15 kW
B=3 kW
G=11 kWE=7.5 kW20
70
0
10
30
40
60
50
0 100 30050 150 250200 350
PV046PV040PV032
D=5.5 kW
E=7.5 kW
G=11 kW
H=15 kW
M=22 kWK=18.5 kW
S=30 kW
31 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplus
Typical Horse Power/Torque Control Characteristics
Performance CurvesF
low
rat
e Q
[l/m
in
Pressure p [bar]
0
50
100
150
200
250
300
350
400
450
500
550
0 50 100 150 200 250 300 350
U=45 kW
W=55 kW
Y=75 kW
Z=90 kW
2=110 kW
3=132 kW
4=160 kW
5=180 kW
6=200 kW
PV360
Speed : n = 1500 rev/minTemperature : t = 50 °CFluid : HLP, ISO VG46Viscosity : ν = 46 mm2/s at 40 °CPressure : Maximum 350 bar, depending on HP level
300
270
240
210
180
150
120
90
60
30
00 50 100 150 200 250 300 350
PV180
W=55 kWU=45 kWT=37 kWM=22 kW
S=30 kW
Y=75 kW
2=110 kWZ=90 kWF
low
rat
e Q
[l/m
in]
Pressure p [bar]
300
350
425
250
200
150
100
50
00 50 100 150 200 250 300 350
PV270
W=55 kWU=45 kWT=37 kW
3=132 kW
Y=75 kW
2=110 kWZ=90 kW
Flo
w r
ate
Q [l
/min
]
Pressure p [bar]
32 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplus
Proportional Displacement ControlControl option FDVThe proportional displacement control allows the adjustment of the pump's output flow by an electrical input signal. The actual displacement of the pump is monitored by an electronic displacement sensor and compared with the commanded displacement in an electronic control module PQDXXA-Z10. The command is given as an electrical input signal (0 - 10 V alternatively 4 - 20 mA) from the supervising machine control or a potentiometer. Version FDV of the proportional control does not provide a pressure compensation. Therefore the hydraulic circuit must be protected by a pressure relief valve.
Control schematics
Response times of the pump are collected from a circuit as below by measuring the pumps swash angle movement at different pressures.
Dynamic characteristic of flow control *
Electronic P/Q Controls
Time on-stroke [ms] Time de-stroke [ms]
stand-byto 50 bar
stand-byto 350 bar
50 bar tostand-by
350 bar tostand-by
PV360 255 154 266 183
Pressure adjustment range* 35 to 350 bar
Differential pressure adjustment range * 10 to 40 bar
Factory setting differential pressure * 15 bar
Control oil consumption (FDV only) Max 0.3 l/min
Internal pilot pressure required to control the pump
FDV 15 bar
UDR 25 bar
UDK 25 bar
UDM 25 bar
* Curve shown exaggerated
* Data valid for UD* version
t on stroke tde-stroke
Dis
plac
emen
t [%
]
0
25
50
75
100
Response time
p
Q
UQ
= FDV included
Load valve
S T
MP1 PAP TAP T
SU
33 Parker Hannifi nPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplusElectronic P/Q Controls
Control option UDRControl version UDR provides electro- hydraulic displacement control and pressure stage mounted on an elbow manifold.
The elbow manifold provides NG6/D03 interface on top to mount a pressure pilot valve (not included in UDR).
Proportional Displacement Control with Overriding Pressure Control
Proportional Displacement Control with Proportional Pressure ControlControl option UDKControl version UDK features proportional pressure pilot valve PVACRE..35, which enables for electro-hydraulic p/Q control.
By using the digital module PQDXXA-Z10 it is possible to control the displacement proportionally with over-riding open loop proportional pressure control.
Proportional Displacement Control with Closed Loop Pressure ControlControl option UDMControl version UDM includes pressure transducer Parker SCP 8181 CE. In combination with control module PQDXXA-Z10 both closed loop pressure control as well as electronic power limitation can be realized.
= UD* included
UP
UQ
Q
p
S T
MP1 PAP TAP T
SU
P
T
M
WV
BP
BD2 AP TAP PT P
P
T
S T
MP1 PAP TAP T
SU
P
T
M
WV
BP
BD2 AP TAP PT P
S T
MP1 PAP TAP T
SU
P
TP
U
M
WV
BP
BD2 AP TAP PT P
34 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplus
00 100 200 300 360
2
4
6
8
10
12
14
4
0
8
12
16
20
0 100 200 3000
20
40
60
80
100
0
5
10
15
20
25
PV020
5
0
10
15
20
25
0 100 200 3000
20
40
60
80
100
0
6
12
18
24
30
PV023 PV028
5
0
10
15
20
25
0 100 200 3000
20
40
60
80
100
0
8
16
24
32
40
Efficiency and case drain flows PV016, PV020, PV023 and PV028The efficiency and power graphs are measured at an input speed of n = 1500 rpm, a temperature of 50 °C and a fluid viscosity of 30 mm2/s.
Case drain flow and compensator control flow leave via the drain port of the pump. To the values shown are to be added 1 to 1.2 l/min, if at pilot operated compensa-tors the control flow of the pressure pilot valve also goes through the pump.
Please note: The values shown below are only valid for static operation. Under dynamic conditions and at rapid compensation of the pump the volume displaced by the servo piston also leaves the case drain port. This dynamic control flow can reach up to 40 l/min! Therefore the case drain line is to lead to the reservoir at full size and without restrictions as short and direct as possible.
Case drain flow PV016-028 with pressure compensator
Efficiency, power consumptionPV016
Efficiency and Case Drain Flows
5
0
10
15
20
25
0 100 200 3000
20
40
60
80
100
0
10
20
30
40
50
Pressure [bar]
Pressure [bar]
Pressure [bar] Pressure [bar]
Pressure [bar]
full flow
dead head
Dra
in fl
ow [l
/min
]
Out
put fl
ow [l
/min
]O
utpu
t flow
[l/m
in]
Out
put fl
ow [l
/min
]
Out
put fl
ow [l
/min
]
Inpu
t pow
er [k
W]
Inpu
t pow
er [k
W]
Inpu
t pow
er [k
W]
Inpu
t pow
er [k
W]
vol. efficiency
vol. efficiency vol. efficiency
overall efficiency
overall efficiency
overall efficiency
over
all e
ffici
ency
input power a
t full fl
ow
input power a
t full fl
ow
input
power
at fu
ll flow
input
pow
er a
t full
flow
input power at deadhead
input power at deadhead
input power at deadheadinput power at deadhead
output flow
output flow, vol. efficiency
output flowoutput flow
Effi
cien
cy[%
](ov
eral
l,vo
lym
etric
)E
ffici
ency
[%](
over
all,
voly
met
ric)
Effi
cien
cy[%
](ov
eral
l,vo
lym
etric
)
Effi
cien
cy[%
](ov
eral
l,vo
lym
etric
)
35 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplus
Efficiency and case drain flows PV032 to PV046The efficiency and power graphs are measured at an input speed of n = 1500 rpm, a temperature of 50 °C and a fluid viscosity of 30 mm2/s.
Case drain flow and compensator control flow leave via the drain port of the pump. To the values shown are to be added 1 to 1.2 l/min, if at pilot operated compensa-tors the control flow of the pressure pilot valve also goes through the pump.
Please note: The values shown below are only valid for static operation. Under dynamic conditions and at rapid compensation of the pump the volume displaced by the servo piston also leaves the case drain port. This dynamic control flow can reach up to 60 l/min! Therefore the case drain line is to lead to the reservoir at full size and without restrictions as short and direct as possible.
Case drain flow PV032-046 with pressure compensator
Efficiency, power consumptionPV032
10
0
20
30
40
50
0 100 200 300 3500
20
40
60
80
100
0
8
16
24
32
40
12
0
24
36
48
60
0 100 200 300 3500
20
40
60
80
100
0
10
20
30
40
50
10
0
20
30
40
50
0 100 200 300 3500
20
40
60
80
100
0
16
32
48
64
80
00 100 200 300 360
2
10
12
14
4
8
6
PV040
PV046
Efficiency and Case Drain Flows
Pressure [bar]
Pressure [bar]
Pressure [bar]
Pressure [bar]
full flow
dead head
Dra
in fl
ow [l
/min
]
Out
put fl
ow [l
/min
]O
utpu
t flow
[l/m
in]
Out
put fl
ow [l
/min
]
Inpu
t pow
er [k
W]
Inpu
t pow
er [k
W]
Inpu
t pow
er [k
W]
vol. efficiency
vol. efficiency
overall efficiency
overall efficiency
overall efficiency
input power a
t full fl
ow
input power a
t full fl
ow
input
power
at fu
ll flow
input power at deadhead
input power at deadhead
input power at deadhead
output flow
output flow, vol. efficiency
output flow
Effi
cien
cy[%
](ov
eral
l,vo
lym
etric
)E
ffici
ency
[%](
over
all,
voly
met
ric)
Effi
cien
cy[%
](ov
eral
l,vo
lym
etric
)
36 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplus
Case drain flows PV063-092
Efficiency, power consumptionPV063
Efficiency and case drain flows PV063, PV080, PV092The efficiency and power graphs are measured at an input speed of n = 1500 rpm, a temperature of 50 °C and a fluid viscosity of 30 mm2/s.
Case drain flow and compensator control flow leave via the drain port of the pump. To the values shown are to be added 1 to 1.2 l/min, if at pilot operated compensa-tors the control flow of the pressure pilot valve also goes through the pump.
Please note: The values shown below are only valid for static operation. Under dynamic conditions and at rapid compensation of the pump the volume displaced by the servo piston also leaves the case drain port. This dynamic control flow can reach up to 80 l/min! Therefore the case drain line is to lead to the reservoir at full size and without restrictions as short and direct as possible.
14
0
28
42
56
70
0 100 200 3000
20
40
60
80
100
0
20
40
60
80
100
16
0
32
48
64
80
0 100 200 3000
20
40
60
80
100
0
24
48
72
96
120
20
0
40
60
80
100
0 100 200 3000
20
40
60
80
100
0
30
60
90
120
150
12
8
4
00 100 200 300 360
PV080
PV092
Efficiency and Case Drain Flows
Pressure [bar]
Pressure [bar]
Pressure [bar]
full flow
dead head
Dra
in fl
ow [l
/min
]
Pressure [bar]
Out
put fl
ow [l
/min
]O
utpu
t flow
[l/m
in]
Out
put fl
ow [l
/min
]
Inpu
t pow
er [k
W]
Inpu
t pow
er [k
W]
Inpu
t pow
er [k
W]
vol. efficiency
vol. efficiency
overall efficiency
overall efficiency
overall efficiency
input pow
er at fu
ll flow
input
power
at fu
ll flow
input
power
at fu
ll flow
input power at deadhead
input power at deadhead
input power at deadhead
output flow
output flow, vol. efficiency
output flow
Effi
cien
cy[%
](ov
eral
l,vo
lym
etric
)E
ffici
ency
[%](
over
all,
voly
met
ric)
Effi
cien
cy[%
](ov
eral
l,vo
lym
etric
)
37 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplus
Efficiency and case drain flows PV140, PV180The efficiency and power graphs are measured at an input speed of n = 1500 rpm, a temperature of 50 °C and a fluid viscosity of 30 mm2/s.
Case drain flow and compensator control flow leave via the drain port of the pump. To the values shown are to be added 1 to 1.2 l/min, if at pilot operated compensa-tors the control flow of the pressure pilot valve also goes through the pump.
Please note: The values shown below are only valid for static operation. Under dynamic conditions and at rapid compensation of the pump the volume displaced by the servo piston also leaves the case drain port. This dynamic control flow can reach up to 120 l/min! Therefore the case drain line is to lead to the reservoir at full size and without restrictions as short and direct as possible.
Efficiency, power consumptionPV140
Case drain flows PV140-180
30
0
60
90
120
150
0 100 200 3000
20
40
60
80
100
0
50
100
150
200
250
35
0
70
105
140
175
0 100 200 3000
20
40
60
80
100
0
60
120
180
240
30018
12
6
00 100 200 300 360
PV180
Efficiency and Case Drain Flows
Pressure [bar]
Pressure [bar]
Out
put fl
ow [l
/min
]O
utpu
t flow
[l/m
in]
Inpu
t pow
er [k
W]
Inpu
t pow
er [k
W]
vol. efficiency
vol. efficiency
overall efficiencyov
eral
l effi
cien
cy
input pow
er at fu
ll flow
input
pow
er a
t full
flow
input power at deadhead
input power at deadhead
output flow
output flow
Effi
cien
cy[%
](ov
eral
l,vo
lym
etric
)E
ffici
ency
[%](
over
all,
voly
met
ric)
Pressure [bar]
full flow
dead head
Dra
in fl
ow [l
/min
]
38 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplus
Efficiency and case drain flows PV270The efficiency and power graphs are measured at an input speed of n = 1500 rpm, a temperature of 50 °C and a fluid viscosity of 30 mm2/s.
Case drain flow and compensator control flow leave via the drain port of the pump. To the values shown are to be added 1 to 1.2 l/min, if at pilot operated compensa-tors the control flow of the pressure pilot valve also goes through the pump.
Please note: The values shown below are only valid for static operation. Under dynamic conditions and at rapid compensation of the pump the volume displaced by the servo piston also leaves the case drain port. This dynamic control flow can reach up to 120 l/min! Therefore the case drain line is to lead to the reservoir at full size and without restrictions as short and direct as possible.
Efficiency, power consumptionPV270
50
0
100
150
200
250
0 100 200 3000
20
40
60
80
100
0
100
200
300
400
500
24
16
8
00 100 200 300 360
Case drain flows PV270
Efficiency and Case Drain Flows
Pressure [bar]
Out
put fl
ow [l
/min
]
Inpu
t pow
er [k
W]
vol. efficiencyoverall efficiency
input
pow
er a
t full
flow
input power at deadhead
output flow
Effi
cien
cy[%
](ov
eral
l,vo
lym
etric
)
Pressure [bar]
full flow
dead head
Dra
in fl
ow [l
/min
]
39 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplusPerformance Curves
Typical efficiency at full displacement and 1500 rpm PV360
The curves show typical characteristics measured under following conditions:Fluid: Mineral oil ISO VG 22 at 32 °CInlet pressure 1,0 bar (absolute), measured at inlet port.
60%
70%
80%
90%
100%
0 25 50 75 100 125 150 175 200 225 250 275 300 325 350
Volumetric
Overall
Pressure [bar]
Effi
cien
cy[%
]
1500
1550
1600
1650
1700
1750
1800
1850
0.8 0.9 1.0 1.1
Typical inlet characteristics vs. speed at various percentage displacements Inlet characteristics PV360 Displacement
95%100%
Inlet pressure [bar]
Sel
f prim
ing
spee
d [r
pm]
0
50
100
150
200
250
300
350
400
0 25 50 75 100 125 150 175 200 225 250 275 300 325 350
0
5
10
15
20
25
30
35
0 25 50 75 100 125 150 175 200 225 250 275 300 325 350
Typical drive power at full displacement Input power – full stroke PV360
Typical compensated power Input power – zero stroke PV360
1750 rpm
1750 rpm
1500 rpm
1500 rpm
Pressure [bar]
Pressure [bar]
Inpu
t pow
er [k
W]
Inpu
t pow
er [k
W]
Case drain flows PV360
Pressure [bar]
Dra
in fl
ow [l
/min
]
24
32
40
16
8
00 100 200 300 360
full flow
dead head
40 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplus
48
133
48
133
48
133
Highpressure
Highpressure
Lowpressure
Lowpressure
DC solenoid 205AC solenoid 190
DC solenoid 205AC solenoid 190
DC solenoid 241AC solenoid 211
ACPV
Function SolenoidFor PV pump
series
AdjustmentSealsAccessories for
controls
Solenoid acces-sories
Mounting bolts
Nominal pressure
PVAC2P* PVAC2M*/PVAC2E*
PVAC1E*PVAC1P*Dimensions
Threads
Accessories Control
AdjustmentCode S
AdjustmentCode L
Code Function
1P Max. pressure relief
1E1 pressure, electrical unloading stand by default
2P 2 pressures, electrical selection
2E2 pressures + stand by electrical selection low pressure default
2M2 pressures + stand by electrical selection stand by default
Code Solenoid voltage
omit For function 1P
Y 110V/50Hz - 120V/60Hz
T 220V/50Hz - 240V/60Hz
J 24V DC
Code Mounting bolts
C For single controls
S Without bolts
M For code UD*/MT*
Code Threads
M Metric
S SAE / UNC
Code Adjustment
SSpindle with lock nut
L DIN lock 1)
1) only for 1P & 2P
Code Solenoid accessories
omit For function 1P
WDIN plug socket without plug
Code Seals
N NBR
V FPM
Code Nominal pressure
35 350 bar
42 420 bar
165
41 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplusAccessories Control
Schematics PVAC1P* Schematics PVAC1E*
Schematics PVAC2P* Schematics PVAC2M*/PVAC2E*
*2M*
42 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplusAccessories Control
Technical data
GeneralNominal size DIN NG06 / CETOP03 / NFPA D03
Mounting position as desired, horizontal mounting preferred
Ambient temperature [°C] -20 ... +70
Weight [kg] 1.8
HydraulicMax. operating pressure [bar] Port P up to 420; port T depressurized
Pressure stages [bar] 350, 420
Fluid Hydraulic oil as per DIN 51524 ... 525
Viscosity, recommended permitted
[cSt]/ [mm²/s][cSt]/ [mm²/s]
30 ... 8012 ... 380
Fluid temperature [°C] -20 ... +60
Filtration ISO 4406 (1999), 18/16/13
Linearity [%] ±4
Repeatability [%] ±2
Hysteresis [%] ±4.5 of pmax
ElectricalDuty ratio [%] 100 ED
Protection class IP 65 in accordance with EN 60529 (plugged and mounted)
Nominal voltage [V] 12 (2.2 A for the 350 bar version; 2,35 A for the 420 bar version)
Coil resistance [Ohm] 4.4 at 20°C
Solenoid connection Connector as per EN 175301-803
Power amplifier, recommended PCD00A-400
Proportional pressure relief valve PVACRE*
FunctionWhen the pressure in port P exeeds the pressure setting at the solenoid, the poppet opens to port T and limits the pressure in port P to the adjusted level.
The optimum performance can be achieved in combina-tion with the digital amplifier module PCD00A-400 (see catalogue HY11-3500 for reference).
43 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplus
Ordering code proportional pressure relief valve
Schematic PVACRE* Dimensions PVACRE*
ACPV
Prop. pressure
valve
Pumpseries PV
SealAccessories for controller
RE K
Nominal pressure
Mounting bolts
Thread option
Accessories Control
Example for PVACRE* mounted
S T
MP1 PAP T
P A T T
P
1/16" NPT for A,M5 for T
Code Nominal pressure
35 350 bar
42 420 bar
Code Seal
N NBR
V FPM
Code Thread option
M Metric
S SAE / UNC
Code Mounting bolts/ ports
C For single controller
S Without bolts
MFor code UD*/MT* design series 45/46
12VDC
44 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplusDimensions
max. 212
1352
Ø25k6
Ø100h8
131
32
10
94
219
79
132max. 130
12
125
5548
15
50
119
43
18
Ø100h8
90
PV016 - 028, metric version
Shown is a clockwise rotating pump with standard pressure compensator. Counter clockwise rotating pumps have inlet, outlet and gage port reversed.
Interface for horse power pilot cartridgeor LVDT fordisplacement feedback
Drain port L1; G1/2"optional M22x1.5; ISO 6149-1(thread options 8)or 7/8"-14 UNF(thread option 3)
Gage port M; G1/4"optional M12x1.5; ISO 6149-1(thread options 8)or 7/16"-20 UNF(thread option 3)
key8x7x40DIN 6885
thread M10,22 deep
Drain port L2 and L3 (opposite); G1/2"optional M22x1.5; ISO 6149-1(thread options 8)or 7/8"-14 UNF(thread option 3)
OUTLET for metric and SAE version:flage acc. ISO 6162DN19; PN400
INLET for metric and SAE version:flage acc. ISO 6162DN32; PN250
4xM10, 18 deepoptional 3/8"-16UNC-2B(thread options 3)
4xM10, 18 deepoptional 7/16"-14UNC-2B(thread options 3)
Mounting optional Lsplined shaft W25x1.5x15x8fDIN 5480
197.5
9.0
28 -0.25
170.5162.5
50.8
23.8
30.2
58.7
The pump shown above has Mounting option Kand thru drive variation T (prepared for thru drive)
45 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplus
A
B27
47
G
E
DF
C
Dimensions
Variation with thru drive
PV016 - 028, SAE version
46
20
50
Key:6.35 x 6.3540 long
Thread:3/8"-16UNC-2B22 deep
Shown above is Mounting option D
Mounting option ESplined shaft 15T-16/32 DP, flat root, side fit ANSI B92.1
Thru drive:splined shaft13T-16/32 DP,flat root, side fit
9.4
Ø25.4 -0.05
Ø28.2 ±0.15
Ø101.6 -0.05
Ø101.6 -0.05
197.5
(224.5)
89.9
89.9
44.9
44.9
13.5
Thru drive adaptors are available with the following dimensionsDrawing Dimension
Thru drive option
A B C D E F G Remark
Metr UNC Metr UNC
A 82.55 8 - - - - 106 M10 3/8"-16 SAE A 2-Bolt
B 101.6 10.5 127 89.8 M12 1/2"-13 - - - SAE B 4-Bolt
H 80 8.5 103 72.8 M8 5/16"-18 109 M10 3/8"-16 2/4-Bolt
J 100 10,5 125 88.4 M10 3/8"-16 - - - 4-Bolt
46 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplus
PV032 - 046, metric version
Dimensions
68
10
9
16
227 max 248
Ø125 h8
Ø125 h8
Ø32 k6
149
138 185
197
71 60
50
17
99
160
14
97
160 max 130
47
PVCMMCN Serie 45 Code AM 350bar
Interface for power pilot cartridge or LVDT for displacement feedback
Drain port L1; G3/4"optional M27 x 2; ISO 6149-1(thread options 8)or 1 1/16"-12 UNF(thread option 3)
Gage port M; G1/4"optional M12x1,5; ISO 6149-1(thread options 8)or 7/16" - 20 UNF(thread option 3)
Drain ports L2 and L3 (opposite); G3/4"optional M27 x 2: ISO 6149-1(thread options 8)or 1 1/16" - 12 UNF(thread option 3)
Thread M10,22 deep
Key10 x 8 x 56DIN 6885
Mounting optional Lsplined shaft W32x1,5x20x8fDIN 5480
OUTLET for metric and SAE version:flange acc. ISO 6162DN25; PN400
4 x M12, 18 deepoptional 7/16"-14 UNC-2B(thread options 3)
INLET for metric and SAE version:flange acc. ISO 6162DN38; PN200
4 x M12, 18 deepoptional 1/2"-13 UNC-2B(thread options 3)
Shown is a clockwise rotating pump with standard pressure compensator. Counter clockwise rotating pumps have inlet, outlet and gage port reversed.
36.5
255.5
112.5
23.5
35-0.25
57.2
27.8
69.9
35.7
The pump shown above has Mounting option Kand thru drive variation T (prepared for thru drive)
47 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplus
At threads options 3 and 7 the dimensions E and G are UNC - 2B threads.
Variation with thru drive
Dimensions
227
(L)K
HB
A
D
F
E
GØC
Thru drive:splined shaftW25x1,5x15x8fDIN 5480
PV032 - 046, SAE version
56
34
860
68
14
8
Key:7.94 x 7.9456 long
Thread:3/8"-16UNC-2B22 deep
Shown above is Mounting option D
Mounting option ESplined shaft 14T-12/24 DP, flat root, side fit ANSI B92.1
114.5
114.5
57.25
57.25
Ø32.5±0.13
Ø127-0.05
Ø127-0.05
Ø31.75-0.05
12.7
12.7
Thru drive adaptors are available with the following dimensionsDrawing Dimension
Thru drive option
A B C D E F G H K L Remark
Metr UNC Metr UNC
A 82.55 8 - - - - 106 M10 3/8"-16 34 48 261 SAE A 2-Bolt
B 101.6 11 127 89.8 M12 1/2"-13 146 M12 1/2"-13 34 48 261 SAE B 2/4-Bolt
C 127 13.5 162 114.6 M12 1/2"-13 - - - 49 63 276 SAE C 4-Bolt
H 80 8.5 103 72.8 M8 5/16"-18 109 M10 3/8"-16 34 48 261 2/4-Bolt
J 100 10.5 125 88.4 M10 3/8"-16 140 M12 1/2"-13 34 48 261 2/4-Bolt
K 125 10.5 160 113.1 M12 1/2"-13 - - - 34 48 261 4-Bolt
48 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplus
236
252
3250
178
132
120
196
Ø16
0 h8
Ø40
k6
200
92
920
910
287
86 7864
26
56
Ø16
0 h8
18
Ø200
121
30
Dimensions
PV 063 - 092 Metric
Mounting interface for horse power pilot or LVDT for displacement feedback
Gage port M; G1/4", optional M12 x 1.5; ISO 6149-1 (tread option 8) or 7/16"- 20 UNF (tread option 3)
Drain ports L1, L2 and L3; G3/4" optional M27 x 2; ISO 6149-1 (tread option 8) or 1 1/16" - 12 UNF (tread option 3)
4 x M12, 20 deep optional 1/2" - 13 UNC - 2B (thread options 3)
4 x M12, 20 deep optional 1/2" - 13 UNC - 2B (thread options 3)or thread options 4: 4 x M14, 20 deep
INLET for metric and SAE version:flange according ISO 6162 DN 51; PN 200 bar
OUTLET for metric and SAE version:flange according ISO 6162 DN 32; PN 400 bar
77.8
66.6
42.9
31.8
187.5
43.5
Max. 308
Max. 133
Key 12 x 8 x 80 DIN 6885
The pump shown above has Mounting option Kand thru drive variation T (prepared for thru drive)
Mounting option L, splined shaftW40 x 1.5 x 25 x 8f DIN 5480
Thread M12 - 28 deep
43-0
.25
Shown is a clockwise rotating pump with standard pressure compensator. Counter clockwise rotating pumps have inlet, outlet and gage port reversed.
49 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplusDimensions
PV 063 - 092 SAE Version
88290
75
287(L)
K
B
A
DF
GE
C
45
H
Key: 11.11x11.11 80 long
Thread1/2"-13UNC-2B28 deep
Mounting option Esplined shaft 13T-8/16 DP,flat root, side fit ANSI B92.1
Output: splined shaftW32x1.5x20x8f DIN 5480
Shown above isMounting option D
Variation with thru drive
Ø15
2.4
Ø44
.45 -
0.05
49.3
-0.0
5
12.6
20.6
80.8
80.8
161.
6
161.6
Ø15
2.4 -
0.05
Thru drive adaptors are available with the following dimensionsDrawing Dimension
Thru drive option
A B C D E F G H K L Remark
Metr UNC Metr UNC
A 82.55 8 - - - - 106 M10 3/8"-16 39 58 326 SAE A 2-BoltB 101.6 11 127 89.8 M12 1/2"-13 146 M12 1/2"-13 39 58 326 SAE B 2/4-BoltC 127 13.5 162 114.6 M12 1/2"-13 181 M16 5/8"-11 39 58 326 SAE C 2/4-BoltD 152.4 13.5 228.5 161.6 M16 5/8"-11 - - - 64 83 351 SAE D 4-BoltH 80 8.5 103 72.8 M8 5/16"-18 109 M10 3/8"-16 39 58 326 2/4-BoltJ 100 10.5 125 88.4 M10 3/8"-16 140 M12 1/2"-13 39 58 326 2/4-BoltK 125 10.5 160 113.1 M12 1/2"-13 180 M16 5/8"-11 39 58 326 2/4-BoltL 160 13.5 200 141.4 M16 5/8"-11 - - - 39 58 326 4-Bolt
50 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplus
350
20
48 92
10
Ø50
k6
Ø16
0 h8
97
202
182
158
145
200
3535
283
230
106
105
146
6332
78
Ø16
0 h8
40
Ø200
18
46
Dimensions
PV 140 - 180 Metric
Mounting interface for horse power pilot or LVDT for displacement feedback
Gage port M; G1/4", optional M12 x 1.5; ISO 6149-1 (tread option 8)or 7/16- 20 UNF (tread option 3)
Drain ports L2; G1" optional M33 x 2; ISO 6149-1 (tread option 8) or 1 5/16" - 12 UNF (tread option 3)
Drain ports L3,dimensions see L2
4 x M12, 20 deep optional 1/2" - 13 UNC - 2B (thread options 3)
4 x M12, 20 deep optional 1/2" - 13 UNC - 2B (thread options 3)or thread options 4: 4 x M14, 22 deep
INLET for metric and SAE version:flange according ISO 6162 DN 64; PN 160 bar
OUTLET for metric and SAE version:flange according ISO 6162 DN 32; PN 400 bar
Key 14 x 9 x 75 DIN 6885
Thread M16 - 36 deep
The pump shown above has Mounting option Kand thru drive variation T (prepared for thru drive)
Mounting option L, splined shaftW50x2x24 x 9g DIN 5480
Bearing flushing port L4; G1/4", optional M12 x 1.5; ISO 6149-1 (tread option 8) or 7/16" - 20 UNF (tread option 3)
Pressure port: 295Suction port: 305
15.4
53.5
-0.2
5
Max. 386Max. 133
9.3
Shown is a clockwise rotating pump with standard pressure control.Counter clockwise rotating pump have inlet, outlet and gage port reversed.31.8
50.8
88.9
66.6
9.3
51 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplusDimensions
PV 140 - 180 SAE Version
(415)
350
97
65
B
A
EG
C
D
F
88 75 75
8
21
40
Key: 12.7x12.7 75 long
Key: 11.11x11.11 55 long
Thread5/8"-11 UNC-2B25 deep
Thread1/2"-13 UNC-2B25 deep
Mounting option Esplined shaft 15T-8/16 DP,flat root, side fit ANSI B92.1
Mounting option Gsplined shaft 13T-8/16 DP,flat root, side fit ANSI B92.1
Output: splined shaftW40x1.5x25x8f DIN 5480
Shown above isMounting option D
Variation with thru drive
Ø15
2.4
-0.0
5
Ø15
2.4
-0.0
5
Ø44
.45
-0.0
5
Ø50
.8 -0
.05
Ø15
2.4
-0.0
5
Ø15
2.4
-0.0
5Mounting option F49.3
±0.
13
56.4
±0.
13
80.8
80.8
161.6
161.
6
12.3
91.4
99.4
52.5
Thru drive adaptors are available with the following dimensionsDrawing Dimension
Thru drive option
A B C D E F G Remark
Metr UNC Metr UNC
A 82.55 8 - - - - 106 M10 3/8"-16 SAE A 2-Bolt
B 101.6 11 127 89.8 M12 1/2"-13 146 M12 1/2"-13 SAE B 2/4-Bolt
C 127 13.5 162 114.6 M12 1/2"-13 181 M16 5/8"-11 SAE C 2/4-Bolt
D 152.4 13.5 228.5 161.6 M16 5/8"-11 - - - SAE D 4-Bolt
H 80 8.5 103 72.8 M8 5/16"-18 109 M10 3/8"-16 2/4-Bolt
J 100 10.5 125 88.4 M10 3/8"-16 140 M12 1/2"-13 2/4-Bolt
K 125 10.5 160 113.1 M12 1/2"-13 180 M16 5/8"-11 2/4-Bolt
L 160 13.5 200 141.4 M16 5/8"-11 - - - 4-Bolt
52 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplusDimensions
PV 270 Metric
250
265
176
184
230
60
9
10
25 115
Ø65
k6
Ø20
0 h8
294
378
403
128
110
100
173
135
22
Ø250
80
200
38
88
46
Mounting interface for horse power pilot or LVDT for displacement feedback
Key 18 x 11 x 98 DIN 6885
Gage port M; G1/4", optional M12 x 1.5; ISO 6149-1 (tread option 8)or 7/16- 20 UNF (tread option 3)
The pump shown above has Mounting option Kand thru drive variation T (prepared for thru drive)
Mounting option L, splined shaftW60 x 2 x 28 x 9g DIN 5480
Thread M20 - 42 deep
Drain ports L1; G1 1/4" optional M42 x 2; ISO 6149-1 (tread option 8) or 1 5/8" - 12 UNF (tread option 3)
Bearing flushing port L4; G1/4", optional M12 x 1.5; ISO 6149-1 (tread option 8) or 7/16" - 20 UNF (tread option 3)
4 x M16, 30 deep optional 5/8" - 11 UNC - 2B (thread options 3)
4 x M16, 30 deep optional 5/8" - 11 UNC - 2B (thread options 3)
INLET for metric and SAE version:flange according ISO 6162 DN 89; PN 35 bar
OUTLET for metric and SAE version:flange according ISO 6162 DN 38; PN 400 bar
120.
7
36.5
79.3
69.9
472.5
Max 510
Shown is a clockwise rotating pump with standard pressure control.Counter clockwise rotating pump have inlet, outlet and gage port reversed.
53 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplusDimensions
Thru drive adaptors are available with the following dimensionsDrawing Dimension
Thru drive option
A B C D E F G Remark
Metr UNC Metr UNC
A 82.55 8 - - - - 106 M10 3/8"-16 SAE A 2-BoltB 101.6 11 127 89.8 M12 1/2"-13 146 M12 1/2"-13 SAE B 2/4-BoltC 127 13.5 162 114.6 M12 1/2"-13 181 M16 5/8"-11 SAE C 2/4-BoltD 152.4 13.5 228.5 161.6 M16 5/8"-11 229 M16 5/8"-11 SAE D 2/4-BoltE 165.1 17 317.5 224.5 M20 3/4"-10 - - - SAE E 4-BoltH 80 8.5 103 72.8 M8 5/16"-18 109 M10 3/8"-16 2/4-BoltJ 100 10.5 125 88.4 M10 3/8"-16 140 M12 1/2"-13 2/4-BoltK 125 10.5 160 113.1 M12 1/2"-13 180 M16 5/8"-11 2/4-BoltL 160 13.5 200 141.4 M16 5/8"-11 224 M20 3/4"-10 2/4-BoltM 200 13.5 250 176.8 M20 3/4"-10 - - - 4-Bolt
Variation with thru drive
PV 270 SAE Version
8
88
C
DF
EG
A
B
98
59
Key: 12.7x12.7 75 long
Thread5/8"-11UNC-2B25 deep
Mounting option Esplined shaft 15T-8/16 DP,flat root, side fit ANSI B92.1
Output: splined shaftW50x2x24x9g DIN 5480
89.5
51.5
15.9
97.5
112.
25
224.
5
112.25
224.5
Ø20
.5
Ø50
.8 -
0.05
56.4
±0.
13
Ø16
5.1
-0.0
5
Ø16
5.1
-0.0
5
Shown above isMounting option D
472.5
(531.5)
54 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplusDimensions
PV 360 Metric
Ø70m7
Ø250h8
265
230
184
176
2560
L2
L3 L1
9
115
910
477
250max. 133
128
117
100
294377
408
38
102
17326
315
24
280
224h8
Ø250h8 (L)
Ø224h8 (T)
80
46
90
Mounting interface forhorse power pilotor LVDT fordisplacement feedback
Key 20 x 12 x 100DIN 6885
Gage port M; G1/4", optional 7/16- 20 UNF (tread option 3)
The pump shown above has Mounting option Kand thru drive variation T (prepared for thru drive)
Mounting option L, T, splined shaftW 70 x 3 x 22 x 8f DIN 5480
mounting option Rpilot diameter Ø224 mm
ThreadM20 - 42 deep
ThreadM20 - 42 deep
Drain ports L1, L2 and L3; G1 1/4"optional 1 5/8" - 12 UNF (thread option 3)
Bearing flushing port L4; G1/4",optional 7/16" - 20 UNF (thread option 3)
4 x M16, 30 deepoptional 5/8" - 11 UNC - 2B(thread option 3)
4 x M16, 30 deepoptional 5/8" - 11 UNC - 2B(thread option 3)
INLET for metric and SAE version:flange according ISO 6162DN 102; PN 35 bar4"
OUTLET for metric and SAE version:flange according ISO 6162DN 38; PN 400 bar1 1/2"
79.3
36.5
77.8
130.2
resp.
max 514.5
74.5-0.25
Shown is a clockwise rotating pump with standard pressure control.Counter clockwise rotating pump have inlet, outlet and gage port reversed.
55 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplusDimensions
PV 360 SAE Version
92100
21
10
90
46
A D
DF
G
E
C
A
B
59
101
477
(536)
78-0.25Ø69.85-0.05 Key:
19.05x19.0588.9 long
Ø165.1-0.05
Thread5/8"-11UNC-2B36 deep
15.6
112.25
112.25
224.5
224.5
Note:The dimensions shown conform to ISO 3019/1the actual hole dimensions conform to ISO 3019/2(pitch Ø315, hole Ø26, see previous page)and cover ISO 3019/1 dimensions as well.Use washers when assembling pump.
165.1-0.05Mounting option Esplined shaft W 70x3x22x8f,DIN 5480
Output: splined shaftW 50x2x24x9g DIN 5480
Shown above is Mounting option D
Variation with thru drive
Thru drive adaptors are available with the following dimensionsDrawing Dimension
Thru drive option
A B C D E F G Remark
Metr UNC Metr UNC
A 82.55 8 - - - - 106 M10 3/8"-16 SAE A 2-BoltB 101.6 11 127 89.8 M12 1/2"-13 146 M12 1/2"-13 SAE B 2/4-BoltC 127 13.5 162 114.6 M12 1/2"-13 181 M16 5/8"-11 SAE C 2/4-BoltD 152.4 13.5 228.5 161.6 M16 5/8"-11 229 M16 5/8"-11 SAE D 2/4-BoltE 165.1 17 317.5 224.5 M20 3/4"-10 - - - SAE E 4-BoltH 80 8.5 103 72.8 M8 5/16"-18 109 M10 3/8"-16 2/4-BoltJ 100 10.5 125 88.4 M10 3/8"-16 140 M12 1/2"-13 2/4-BoltK 125 10.5 160 113.1 M12 1/2"-13 180 M16 5/8"-11 2/4-BoltL 160 13.5 200 141.4 M16 5/8"-11 224 M20 3/4"-10 2/4-BoltM 200 13.5 250 176.8 M20 3/4"-10 - - - 4-Bolt
56 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplus
Dimensions standard pressure control, code ...MMC
Pump Dimensions
45
73
max. 172 4641
24
4554
PT
L
A
max. 17241
24
45
LP
P
TA
Pump axis
Controls with code ...MM1 have a NG6 / Cetop 3 interface topside (as shown below)
Dimensions remote pressure and load sensing control, codes ...MR1, ...MF1
Pump axis
Controls with code ...MRC and MFC have no topside valve interface (as shown above)
Dimensions horse power pilot cartridge, displacement sensor
remote control port pP (code ...MRC, ...MR1) resp.LS port pF (code ...MFC, ...MF1)
Pump housing
All control ports G1/4Optional 7/16-20 UNF (option 3)
69.5
43.4
43.4
88.5
88.5
37.5
57 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplus
Dimensions for controls with unloading valve, codes ...M*W
Dimensions for controls with proportional pressure pilot valve, codes ...M*K
Pump Dimensions
171130
96
173
97
41
Pump axis
Pump axis
remote control port pPresp. LS port pF
remote control port pPresp. LS port pF
unloading valve:D1VW002K*JW;* for seals option
Shown in version MRW/MFW, version MMW has no remote control port.
pilot valve:PVACREC**35 for codes ...M*K,** for threads and seals option
Shown in version MRK/MFK, version MMK has no remote control port.Dimensions for horse power compensator *L* and *C* are identical to MM* respectively MF*.
All control ports G1/4Optional 7/16-20 UNF (option 3)
43.4
43.4
58 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplusPump Dimensions
5829
96
105
81
116
88
110
222
58
104
29
191
96
110
88
Pump axis
Pump axis
Dimensions two spool load sensing control, code ...MT1, ...MTP
LS port pF
LS port pF
pressure pilot valvePVAC1PC**S35(code ...MTP only)
pressure controlstage
elbow manifold
elbow manifold
displacementcontrol stage
displacementcontrol stage
Dimensions two spool load sensing control with proportional pressure pilot valve, code ...MTK
pilot valve:PVACREM**35 for code ...MTK,** for threads- and seals soption
proportionalpressure pilot valve
pressure controlstage
80.5
59 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplus
95
8010
6
58
222
2881 11
3
145 10
8
106
A
B
Pump Dimensions
pump axis
Dimensions proportional p/Q-control, codes ...UDR, ...UDK, ...UDM
pilot valve:PVACREM**K35 for code ...UDK, UDM** for threads- and seals option
pressure pilot valve(codes ...UDK, ...UDM only)
pressure sensor(code ...UDM only)
pressurecontrol stage
elbow manifolddisplacementcontrol stage
Dimensions proportional displacement control, code ...FDV
P
T
A
101,9 122,9
pump axis
56,7
81,7
46,0
A
B
60 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplus
Technical data
For programming the module via PC an interface cable is needed, please order part number PQDXXA-ZXX-KABEL separately.
Ordering code
OptionFor all frame sizes series PV
Digital control module for p/Q
control
Version A
PQD XX A Z10
Electronic Module PQDXXA
Programming softwareThe programming of the p/Q control module is done in an easy to learn mode. To select the pump model and size and to set the control paramters the program ProPVplus must be started. This program runs under WINDOWS® 95 and higher.The latest version of this software can be downloaded at the following internet address: www.parker.com/pmde
Features• Displayanddocumentationofparametersets• Saveondreloadofoptimizedparametersets• Offersoscilloscopefunctionforeasyperformanceevalu-
ation and optimization• ParametersetsforallPVpluspumpsarepre-installed
in the modules
Mounting style Snap-on mounting for EN50022 rail
Body material Polycarbonate
Inflammation class V2...V0 acc. UL 94
Mounting position any
Env. temperature range [°C] -20...+55
Protection class IP 20 acc. DIN 40 050
Weight [g] 260
Duty ratio [%] 100
Supply voltage [V] 18...30VDC,ripple<5%eff.
Rush in current [A] 22 for 0.2 ms
Current consumption [A] < 4 for p/Q control ; < 2 for Q-control
Resolution Input Command [%] 0.025 (power 0.1)
Interface USB - Typ B
EMC EN 50 081-2, EN 50 082-2
Connctors Screw terminals 0.2...2.5 mm², plug in style
Cables [mm²] Supply and solenoid cables; 1,5 mm2 (AWG16) overall braid shield. Sensor and command signals; 0,5 mm2 (AWG20) overall braid shield
Max. cable length [m] 50
Features• Digitalcontrolcircuit• Coversalldisplacements• Coversallavailablefunctions• Predefinedparametersets(Plug&Play)• ConnectionviaUSBcable(USB-A/USB-B)• Ramptimeupto60seconds• CompatibletotherelevanteuropeanEMC
specifications• Offlineeditionofparametersets• Easyerrordiagnosis• Hands-oncontroltuningduetoonlinemonitoringof
PID gains• Allsettings(ramps,MIN/MAX,controlparameters)
can be stored digitally and recalled from a PC to dublicate settings to other modules
61 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplusThru Drive, Mounting Kits
SealsSecond pump Thread
PVMK
Axial piston pump
series PV
BG
Size
1
2
Mounting kit
PVMK
Axial piston pump
series PV
BG
SizeMounting kit
Coupling
Mounting kits for multiple pumps, for second pump option
Mounting kits for multiple pumps, couplings
Kit contains positions 30, 69, 84, 85 and 87, see spare part list
Kit contains positions 1 (and 2 for keyed shaft).
K
SAE,splined
keyed shaft(only up to Ø18,metric)
metricsplined
second pumpfront pump
Availability of thru drive flange and coupling please check with ordering code options per each pump size, starting at page 6
Code Second pump, SAET Prepared for thru drive option (plugged)Y SAE AA, diameter 50.8 mmA SAE A, diameter 82.55 mm B SAE B, diameter 101.6 mmC SAE C, diameter 127,mmD SAE D, diameter 152.4 mmE SAE E, diameter 165.1 mm
Second pump, metricG Diameter 63 mmH Diameter 80 mmJ Diameter 100 mmK Diameter 125 mmL Diameter 160 mmM Diameter 200 mm
CodeCoupling for metric, splined shaft DIN 5480
01 N25 x 1.5 x 1502 N32 x 1.5 x 2003 N40 x 1.5 x 2504 N50 x 2 x 2405 N60 x 2 x 2806 N70 x 3 x 22*
Coupling for SAE splined shaft flat root, side fit
11 SAE A, 9T 16/3212 SAE-, 11T 16/3213 SAE B, 13T 16/3214 SAE B-B, 15T 16/3215 SAE C, 14T 12/2416 SAE C-C, 17T 12/2417 SAE D+E, 13T 8/1618 SAE F, 15T 8/16
Coupling + adaptor for keyed shaf
20 Diameter 12 mm21 Diameter 16 mm22 Diameter 18 mm
* For PV360 only
Code Pump size
1 Pump size 1: PV016 - PV028
2 Pump size 2: PV032 - PV046
3 Pump size 3: PV063 - PV092
4 Pump size 4: PV140 - PV180
5 Pump size 5: PV270 - PV360
Code Pump size
1 Pump size 1: PV016 - PV028
2 Pump size 2: PV032 - PV046
3 Pump size 3: PV063 - PV092
4 Pump size 4: PV140 - PV180
5 Pump size 5: PV270 - PV360
Code Seals
N NBR
V FPM
Code Thread
M Metric
S SAE
62 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplusThru Drive, Flange Load Limitation
L1
L2
L3
W1W2
W3
LP
Multiple Pump Combinations - Maximum MomentCombinations of multiple pumps might require additional pump support to avoid a too high stress on the front mounting flange. Combinations of two PVplus pumps in the same frame size generally do not need additional support in an industrial application. For combinations of more pumps support is required.
In case of combinations of a PVplus pump with another type of pump it is recommended to calculate the moment for the combination and compare with the maximum moment in table 1 below.
Moment M = (L1*W1 + L2*W2 + L3*W3 +...)Note:If the calculated moment M exceed the maximum moment in table 1 below, additional pump support is needed
Table 1: Maximum Moment and Pump Dimensions
PV016-PV028 PV032-PV046 PV063-PV092 PV140-PV180 PV270 PV360
Maximum moment 1) [Nm] 81 151 401 591 1686 1686
Weight W [N] 186 294 589 883 1687 1766
Distance L1 [mm to C/G] 106 119 178 184 234 238
Distance Lp [mm] 197.5 227 287 350 472.5 477
1) at dynamic weight acceleration 10g = 98.1 m/sec2
Table 2 Through Drive Adapter Plate Thickness [mm]
Adapter option 2) PV016-PV028 PV032-PV046 PV063-PV092 PV140-PV180 PV270 PV360
Y 27 - - - - -
A 27 34 39 65 59 59
B 27 34 39 65 59 59
C - 49 39 65 59 59
D - - 64 65 59 59
E - - - - 59 59
G 27 34 39 - - -
H 27 34 39 65 59 59
J 27 34 39 65 59 59
K - 34 39 65 59 59
L - - 39 65 59 59
M - - - - 59 59
2) See page 6 to 17 for reference per each frame size.
63 Parker HannifinPump & Motor Division EuropeChemnitz, Germany
Catalogue HY30-3245/UK Axial Piston PumpsSeries PVplusThru Drive, Shaft Load Limitations
Important noticeThe max. allowable torque of the individual shaft must not be exceeded. For 2-pump combinations there is no problembecausePVseriesoffers100%thrutorque.For3-pump combinations (and more) the limit torque could be reached or exceeded.
Therefore it is necessary to calculate the resulting input as well as thru drive torque.
Maximum allowed transferable torque FRONTShaft code
Shaft type
Transferable torque at FRONT shaft end. [Nm]
PV016-028 PV032-046 PV063-092 PV140-180 PV270 PV360
D SAE - Key 300 650 1850 2150 2150 4750
E SAE - Spline 320 630 1700 2750 2800 8100*
F SAE - Key 1200
G SAE - Spline 1700
R Metric - Key 3750
T Metric - Spline 8100
K Metric - Key 280 640 1200 1550 3300 3750
L Metric - Spline 320 720 1500 3050 5750 8100
Maximum allowed transferable torque REARMax. torque transmission cap. for rear mounted pump
350 520 1100 1550 3150 3250
* DIN5480 splined
FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS DESCRIBED HEREIN OR RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE.
This document and other information from Parker-Hannifin Corporation, its subsidiaries and authorized distributors provide product or system options for further investigation by users having technical expertise.
The user, through its own analysis and testing, is solely responsible for making the final selection of the system and components and assuring that all performance, endurance, maintenance, safety and warning requirements of the application are met. The user must analyze all aspects of the application, follow applicable industry standards, and follow the information concerning the product in the current product catalog and in any other materials provided from Parker or its subsidiaries or authorized distributors.
To the extent that Parker or its subsidiaries or authorized distributors provide component or system options based upon data or specifications provided by the user, the user is responsible for determining that such data and specifications are suitable and sufficient for all applications and reasonably foreseeable uses of the components or systems.
Offer of SalePlease contact your Parker representation for a detailed ”Offer of Sale”.
WARNING – USER RESPONSIBILITY
Catalogue HY30-3245/UK. POD, 02/2017, ZZ© 2017 Parker Hannifin Corporation. All rights reserved.
Your local authorized Parker distributor
Ed
. 201
6-04
-04
EMEA Product Information CentreFree phone: 00 800 27 27 5374(from AT, BE, CH, CZ, DE, DK, EE, ES, FI, FR, IE, IL, IS, IT, LU, MT, NL, NO, PL, PT, RU, SE, SK, UK, ZA)
US Product Information CentreToll-free number: 1-800-27 27 537
www.parker.com/pmde
Parker WorldwideEurope, Middle East, AfricaAE – United Arab Emirates, Dubai Tel: +971 4 8127100 [email protected]
AT – Austria, Wiener Neustadt Tel: +43 (0)2622 23501-0 [email protected]
AT – Eastern Europe, Wiener Neustadt Tel: +43 (0)2622 23501 900 [email protected]
AZ – Azerbaijan, Baku Tel: +994 50 22 33 458 [email protected]
BE/LU – Belgium, Nivelles Tel: +32 (0)67 280 900 [email protected]
BG – Bulgaria, Sofia Tel: +359 2 980 1344 [email protected]
BY – Belarus, Minsk Tel: +48 (0)22 573 24 00 [email protected]
CH – Switzerland, Etoy Tel: +41 (0)21 821 87 00 [email protected]
CZ – Czech Republic, Klecany Tel: +420 284 083 111 [email protected]
DE – Germany, Kaarst Tel: +49 (0)2131 4016 0 [email protected]
DK – Denmark, Ballerup Tel: +45 43 56 04 00 [email protected]
ES – Spain, Madrid Tel: +34 902 330 001 [email protected]
FI – Finland, Vantaa Tel: +358 (0)20 753 2500 [email protected]
FR – France, Contamine s/Arve Tel: +33 (0)4 50 25 80 25 [email protected]
GR – Greece, Athens Tel: +30 210 933 6450 [email protected]
HU – Hungary, Budaoers Tel: +36 23 885 470 [email protected]
IE – Ireland, Dublin Tel: +353 (0)1 466 6370 [email protected]
IT – Italy, Corsico (MI) Tel: +39 02 45 19 21 [email protected]
KZ – Kazakhstan, Almaty Tel: +7 7273 561 000 [email protected]
NL – The Netherlands, Oldenzaal Tel: +31 (0)541 585 000 [email protected]
NO – Norway, Asker Tel: +47 66 75 34 00 [email protected]
PL – Poland, Warsaw Tel: +48 (0)22 573 24 00 [email protected]
PT – Portugal Tel: +351 22 999 7360 [email protected]
RO – Romania, Bucharest Tel: +40 21 252 1382 [email protected]
RU – Russia, Moscow Tel: +7 495 645-2156 [email protected]
SE – Sweden, Spånga Tel: +46 (0)8 59 79 50 00 [email protected]
SK – Slovakia, Banská Bystrica Tel: +421 484 162 252 [email protected]
SL – Slovenia, Novo Mesto Tel: +386 7 337 6650 [email protected]
TR – Turkey, Istanbul Tel: +90 216 4997081 [email protected]
UA – Ukraine, Kiev Tel: +48 (0)22 573 24 00 [email protected]
UK – United Kingdom, Warwick Tel: +44 (0)1926 317 878 [email protected]
ZA – South Africa, Kempton Park Tel: +27 (0)11 961 0700 [email protected]
North AmericaCA – Canada, Milton, Ontario Tel: +1 905 693 3000
US – USA, Cleveland (industrial) Tel: +1 216 896 3000
US – USA, Elk Grove Village (mobile) Tel: +1 847 258 6200 Asia PacificAU – Australia, Castle Hill Tel: +61 (0)2-9634 7777
CN – China, Shanghai Tel: +86 21 2899 5000
HK – Hong Kong Tel: +852 2428 8008
ID – Indonesia, Tangerang Tel: +62 21 7588 1906
IN – India, Mumbai Tel: +91 22 6513 7081-85
JP – Japan, Fujisawa Tel: +81 (0)4 6635 3050
KR – South Korea, Seoul Tel: +82 2 559 0400
MY – Malaysia, Shah Alam Tel: +60 3 7849 0800
NZ – New Zealand, Mt Wellington Tel: +64 9 574 1744
SG – Singapore Tel: +65 6887 6300
TH – Thailand, Bangkok Tel: +662 186 7000
TW – Taiwan, New Taipei City Tel: +886 2 2298 8987
VN – Vietnam, Ho Chi Minh City Tel: +84 8 3999 1600 South AmericaAR – Argentina, Buenos Aires Tel: +54 3327 44 4129
BR – Brazil, Cachoeirinha RS Tel: +55 51 3470 9144
CL – Chile, Santiago Tel: +56 2 623 1216
MX – Mexico, Toluca Tel: +52 72 2275 4200