av/s-video to vga converter (with audio and vga bypass) › uploadfile › downloads ›...
TRANSCRIPT
Note:1. ON/VGA BYPASS – Power on mode / VGA bypass mode. VGA bypass mode is power down mode (standby mode). Audio output will be cut off in VGA bypass mode2. OSD menu – On Screen Display menu3. SOURCE – AV/S-video input selection4. MODE – change VGA output resolution5. PIP – Picture in picture mode6. Picmode – Picture mode : Normal/User/Bright/Soft7. VGA ADJUST – adjust PIP screen at PIP mode
Front buttonPanel
4 : 3800 x 600 60Hz800 x 600 75Hz1024 x 768 60Hz1024 x 768 75Hz1280 x 1024 60Hz1280 x 1024 75Hz1600 X 1200 60Hz
16 : 91366 x 768 60Hz1600 x 900 60Hz1920 x 1080 60Hz
16 : 101440 x 900 60Hz1680 x 1050 60Hz1920 x 1200 60Hz
Supported VGA output resolution
BUTTON
MAIN
OSD MENU MODE
PIP MODE
1
ON / VGA BYPASS
2
OSD MENU
Back / Exit OSD
VGA ADJUST
3
SOURCE
UP
4
MODE
DOWN
CHANGE PIPPOSITION
5
PIP
ENTER / LEFT
EXIT PIP MODE
6
Picmode
ENTER / RIGHT
CHANGE PIP SIZE
MODE
Connection
Output
Input
AV/S-video to VGA converter(with audio and VGA bypass)
Audio output(3.5mm audio jack)
VGA output
Front button panel
S-video input
Poweradapter
Audio input(Right channel)
Audio input(Left channel)
AV video input
VGA input
Status lightLight on - AV/S-video modeLight flash - VGA bypass mode
Master power switch
DC Jack (connect to power adapter)
Orion-V2 User manual
Input interface
Output interface
Maximum VGA output resolutionMinimum VGA output resolutionSupport output ratio
Picture adjustment
Support input video standard
OSD menuPIP mode supportSetting store (Save) support
Restore to factory mode (Default) supportWall- mount supportAuto Power onPower supplyProduct DimensionProduct WeightAccessory
1920 x 1200 @60Hz800 x 600 @60Hz4:3, 16:9, 16:10
Brightness, Contrast, Hue, Saturation, Color temperature
NTSC /PAL/SECAM
1) VGA2) AV (CVBS) - RCA connector3) S-video4) audio (RCA x 2 – Left & Right)
1) VGA2) audio (3.5mm audio jack)
YesYesYes
Yes
YesYes5V @ 1A (DC jack)5.2 x 3.54 x 1.28 inches / 132 x 90 x 32 mm 5.1 ounces / 145 gramVGA cablePower adapter
Specification
• The user can change the size and position of AV/s-video screen window in PIP mode• If “Unknown resolution” message appears on screen when the user try to enter PIP mode. It means that the product cannot detect the VGA input resolution. Please change VGA input resolution on Windows and try again.
Power switch1) Master power switch 2) Power on / VGA pypass mode button
At Power on mode: press 3 second to switch to VGA bypass modeAt VGA bypass mode: press 1 second to switch to Power on mode
Note: The product will automatically power on when the power is connected
Press Key 2 to enter OSD menu
OSD menu
PIP mode
Master power on
Master power cut off
Press Key 2 for back or exit OSD menuPress Key 3 for moving upPress Key 4 for moving downPress Key 5 or 6 for enterPress Key 5 for moving leftPress Key 6 for moving right
© 2017 by Pirect International Limited. All rights reserved. Information in this document is subject to change without notice. Pirect International Limited reserves the right to modify, change, improve or enhance its products and to make changes in the content without obligation to notify any person or organization of such changes. Please visit www.pirect.com to get the updates of the operation and use of Pirect products.
Picture shown may vary from actual product.
Pirect International LimitedWebsite www.pirect.comTel +852-26718778Email [email protected]