atex installation instructions

Installation InstructionsP/N MMI-20011705, Rev. AJuly 2008

ATEX Installation Instructions for Micro Motion Model 1700, 2700, and 2750 Transmitters

Note: For hazardous installations in Europe, refer to standard EN 60079-14 if national standards do not apply.

2008, Micro Motion, Inc. All rights reserved. ELITE and ProLink are registered trademarks, and MVD and MVD Direct Connect are trademarks of Micro Motion, Inc., Boulder, Colorado. Micro Motion is a registered trade name of Micro Motion, Inc., Boulder, Colorado. The Micro Motion and Emerson logos are trademarks and service marks of Emerson Electric Co. All other trademarks are property of their respective owners.

Information affixed to equipment that complies with the Pressure Equipment Directive can be found on the internet at www.micromotion.com/library.

Reference no. EB-3600636 Rev. I

1Model 1700/2700/2750 TransmittersATEX Installation Instructions and Drawings

For installing the following Micro Motion transmitters:- Model 1700/2700/2750 with a 4-wire connection to a core processor- Model 1700/2700/2750 with a 9-wire connection to a junction box- Model 1700/2700/2750 with a remote core processor and remote sensor with a

junction box

Subject: Equipment type Transmitter type *700********** andTransmitter type *750**********

Manufactured and submitted for examination

Micro Motion, Inc.

Address Boulder, Co. 80301, USA

Standard basis EN 60079-0:2006 General requirements

EN 60079-1:2004 Flameproof enclosure d

EN 60079-7:2003 Increased safety e

EN 60079-11:2007 Intrinsic safety i

EN 61241-0:2006 and EN 61241-1:2004

Dust evaluation tD A

EN 60079-26:2004 Equipment Group II, Category 1G

EN 60079-27:2006 FISCO/FNICO

Code for type of protection Ex d [ib] IIB + H2 T6, Ex de [ib] IIB + H2 T5/T6 Ex d [ia/ib] IIB + H2 T6, Ex de [ia/ib] IIB + H2 T5/T6 Ex d [ib] IIC T6, Ex de [ib] IIC T5/T6 Ex d [ia/ib] IIC T6, Ex de [ia/ib] IIC T5/T6 Ex tD A21 IP66/IP67 T65C

ATEX Installation Instructions

Model 1700/2700/2750 Transmitters

2 ATEX Installation Instructions

1) Subject and type

Transmitter type *700********** and type *750**********

Instead of the *** letters and numerals will be inserted which characterize the following modifications:

Marking without influence to the type of protection

* 7 5 0 * 1 * * * * * * *

Numeral1 = Single variable transmitter2 = Multivariable transmitter

Letter for conduit connections

Letter for outputsA = One mA, one frequencyB = Config I/O defaultC = Config I/O customD = Intrinsically safe outputsE = Intrinsically safe FOUNDATION fieldbus H1G = PROFIBUS-PAN = Non-I.S. FOUNDATION fieldbus H1J = Config I/O default (Model *750 only)K = Config I/O custom (Model *750 only)

*

Letter for mountingR = Remote mount (4-wire connection)I or S = Integral mountC = Remote mount (9-wire connection)B = Remote mount transmitter with remote mount

core processorD = Integral mount (Model *750 only)E = Remote mount (Model *750 only)

Numeral for display1 = With display: Ex *** IIB + H22 = With backlight display: Ex *** IIB + H23 = Without display: Ex *** IIC4 = With IIC display: Ex *** IIC4 with ETO 12638 = Ex ***IIC with FEP face plate5 = With IIC backlight display: Ex *** IIC5 with ETO 12638 = Ex ***IIC with FEP face plate

ApprovalF = Ex d ****Z = Ex de ****

* 7 0 0 * 1 * * * * * * **


ATEX Installation Instructions 3

2) Description

The transmitter is, in combination with a sensor, used for measurement of mass flow and data transmission.

The electrical circuitry of the transmitters is mounted inside a metal enclosure type 1700/2700/*750..*..*..which is divided into three compartments.

In the compartment type of protection Flameproof Enclosure the Terminal Board, Power Supply Board, Feature Board, Digital Board and Fieldbus Board (only type 2700*1******** and type 2750*1********) are mounted.

When executed with display, there are two window covers available, one for IIB + H2 and one for IIC. ETO 12638 adds an FEP plate over the glass window in the display cover. When it is executed without the display, the gas group is IIC.

The compartment Increased Safety (type *7*0*1***Z****) or Flameproof Enclosure (type *7*0*1***F*****) is equipped with terminals for the connection of intrinsically safe fieldbus circuit as well as non intrinsically safe circuits as well as intrinsically safe outputs.

The enclosure is constructed with a terminal compartment for the connection of remotely operating intrinsically safe sensors (type *700R1******** and type *750E1********) or to remote mount core (*700B1********). Alternatively, the enclosure can be mounted directly to the sensor via a transition compartment for the incorporation of the signal processing device type 700 (type *700I1******** and type *750D1********). This type of mounting has to be certified separately.

The transmitter type *7*0C1******** is constructed with a terminal compartment for the incorporation of the signal processing device type 700 and a connection board.

The transmitter is intended to be used in a hazardous dust environment without change to any of the electronics aspects of the design.

Amendment 8 to the ATEX certificate DMT 01 ATEX E 082 X incorporates the new EN 60079 series standards and therefore the marking changed from EEx to Ex. Additionally this amendment uses the new dust standards EN 61241-0:2006 and EN 61241-1:2004 and therefore changed the dust marking by adding "Ex tD A21". This amendment also added the non-IS fieldbus option N and changed the maximum voltage (Um) for the non-IS input/output circuits from 60 Vdc to 33 Vdc.

Amendment 9 to the ATEX Certificate DMT 01 ATEX E 082 X incorporates the new model *750*1********. Additionally this amendment incorporates the revised fieldbus board, analog board, and terminal board. The revised fieldbus board corrects a digital communication issue when transmitting fieldbus data and does not impact safety. The analog board was revised to eliminate a non-safety critical inductor (FL1) and added a pull up resistor to the HART transmit line to correct communication error. The terminal board was revised to replace an obsolete non-safety critical inductor (FL3) with an equivalent inductor requiring an artwork change to accommodate the new inductor spacing.

3) Parameters

3.1) Mains circuit (terminals 910)

3.2) Non intrinsically safe input/output circuits (terminals 16) only for type *700*1*(A, B, C, J, or K)******

Voltage AC/DC 18240 V + 10%Max voltage Um AC/DC 265 V

Voltage Um AC/DC 33 V



3.2.1) Non-intrinsically safe circuits fieldbus (terminals fieldbus 12) only for type *700*1*N******

3.3) Intrinsically safe output circuits type of protection Ex ia IIC

3.4) Intrinsically safe power and signal circuits for type *700R1******** or *700B1******** or *750E1********

3.4.1) Ambient temperature range


*700*1*N******Fieldbus terminals 12 FNICO(1)

(1) For connection of a FOUNDATION fieldbus circuit in accordance with the FNICO model.

Voltage Um (Vdc) 33Current Im (mA) 380Power Pm (W) 5,32Effective internal inductance L NegligibleEffective internal capacitance C Negligible

*7*0*1*D****** 27*0*1*E****** 27*0*1*G******mA / HARTterminals 12 & 56

FOterminals 34

Fieldbus terminals 12 FISCO(1)

(1) For connection of a FOUNDATION fieldbus circuit in accordance with the FISCO model.

PROFIBUS terminals 12 FISCO(1)

Voltage Ui (Vdc) 30 30 30 30Current Ii (mA) 300 100 380 380Power Pi (W) 1 0,75 5,32 5,32Effective internal inductance Li Negligible Negligible Negligible NegligibleEffective internal capacitance Ci Negligible Negligible Negligible Negligible

Voltage Uo (Vdc) 17,22Current Io (A) 0,484Limited by a fuse with a nominal value of In (A) 0,16Power Po (W) 2,05

Type of protection Ex ib IIC Ex ib IIBMax. external inductance Lo (H) 151 607Max. external capacitance Co (F) 0,333 2,04Max. inductance/resistance ratio Lo/Ro (H/) 17,06 68,2

Models *7*0(R, B, or E)1(1, 2, or 3)******* Ta 40 C up to +60 C

Models *7*0(R, B, or E)1(4 or 5)******* Ta 20 C up to +60 C



3.5) Intrinsically safe power and signal circuits for type *7*0C1********

The maximum external inductance L (sensor coil) can be calculated with the following term:

whereby E = 40 J for group IIC and E = 160 J for group IIB will be inserted.Ro is the drive coil resistance plus the drive coil series resistor resistance.



Drive circuitterminals 34

Pick-off circuitsterminals 56 and 78

Temperature circuit terminals 1, 2, and 9

Voltage Uo 10,5 Vdc 17,3 Vdc 17,3 VdcCurrent Io 2,45 A 6,9 mA 26 mAPower Po 2,54 W 30 mW 112 mWInternal resistance Ri 4,32

Group IIC IIB IIC IIB IIC IIBMax. external inductance Lo 5,9 H 24 H 742 mH 2,97 H 52,6 mH 210 mHMax. external capacitance Co 2,41 F 16,8 F 353 nF 2,06 F 353 nF 2,06 FMax. inductance/resistance ratio

Lo/Ro 5,5 H/ 22 H/ 1,19 mH/

4,75 mH/

0,32 mH/

1,26 mH/

Models *7*0C1(1, 2, or 3)******* Ta 40 C up to +55 C

Models *7*0C1(4 or 5)******* Ta 20 C up to +55 C

L 2 E Ri Ro+1.5 Uo---------------------- 2=



4) Marking

5 min. delay time after switch off

Models *7*0*1(1, 2, or 3)******* Ta 40 C up to +55 CModels *7*0*1(4 or 5)******* Ta 20 C up to +55 C

- type - type of protection

*700(B, R, or E)1(1 or 2)(A, B, C, N, J, or K)*F**** 0575 II 2G Ex d[ib] IIB+H2 T6

II 2D Ex tD A21 IP66/IP67 T65 C

*700(B, R, or E)1(1 or 2)(A, B, C, N, J, or K)*Z**** 0575 II 2G Ex de[ib] IIB+H2 T6


*700(B, R, or E)1(3, 4, or 5)(A, B, C, N, J, or K)*F**** 0575 II 2G Ex d[ib] IIC T6


*700(B, R, or E)1(3, 4, or 5)(A, B, C, N, J, or K)*Z**** 0575 II 2G Ex de[ib] IIC T6


*700(B, R, or E)1(1 or 2)(D, E, or G)*F**** 0575 II 2 (1) G Ex d[ia/ib] IIB+H2 T6


*700(B, R, or E)1(1 or 2)(D, E, or G)*Z**** 0575 II 2 (1) G Ex de[ia/ib] IIB+H2 T6


*700(B, R, or E)1(3, 4, or 5)(D, E, or G)*F**** 0575 II 2 (1) G Ex d[ia/ib] IIC T6


*700(B, R, or E)1(3, 4, or 5)(D, E, or G)*Z**** 0575 II 2 (1) G Ex de[ia/ib] IIC T6


*700(C, I, S, or D)1(1 or 2)(A, B, C, N, J, or K)*F**** 0575 II 2G Ex d[ib] IIB+H2 T5


*700(C, I, S, or D)1(1 or 2)(A, B, C, N, J, or K)*Z**** 0575 II 2G Ex de[ib] IIB+H2 T5


*700(C, I, S, or D)1(3, 4, or 5)(A, B, C, N, J, or K)*F**** 0575 II 2G Ex d[ib] IIC T5


*700(C, I, S, or D)1(3, 4, or 5)(A, B, C, N, J, or K)*Z**** 0575 II 2G Ex de[ib] IIC T5


*700(C, I, S, or D)1(1 or 2)(D, E, or G)*F**** 0575 II 2 (1) G Ex d[ia/ib] IIB+H2 T5


*700(C, I, S, or D)1(1 or 2)(D, E, or G)*Z**** 0575 II 2 (1) G Ex de[ia/ib] IIB+H2 T5


*700(C, I, S, or D)1(3, 4, or 5)(D, E, or G)*F**** 0575 II 2 (1) G Ex d[ia/ib] IIC T5


*700(C, I, S, or D)1(3, 4, or 5)(D, E, or G)*Z**** 0575 II 2 (1) G Ex de[ia/ib] IIC T5




5) Special conditions for safe use / Installation instructions

5.1) For the application of the transmitter in an ambient temperature of less than 20 C suitable cable and cable entries or conduit entries certified for this condition shall be used.

5.2) If certified conduit entries are used for the connection of the transmitter enclosure, the associated stopping boxes shall be installed immediately at the enclosure.

5.3) Addition for version *7*0*1(4 or 5) ** (Z or F) **** CEQ/ETO 12638 only:

Using a dry cloth to clean the display cover can cause static discharge, which could result in an explosion in an explosive atmosphere.To prevent an explosion, use a clean damp cloth to clean the display cover in an explosive atmosphere.

Model 1700/2700/2750 installation drawings

Figure 1: Model 1700/2700/2750 transmitter to remote core processor

I.S.cable See note 5.

VDC

+VD

C

I.S. 1700/2700/2750 outputs to core processor entity parameters

Vdc

Remote installation

(WARNING: SUBSTITUTIONS OF COMPONENTS MAY IMPAIR INTRINSIC SAFETY)

Increased safety version:No DisplayEx de [ia/ib] IIC T5With DisplayIIB cover: Ex de [ia/ib] IIB + H2 T5IIC cover: Ex de [ia/ib] IIC T5

Refer to Model Number on 1700/2700/2750 transmitter tag for specific Hazardous Location

Flameproof version:No DisplayEx d [ia/ib] IIC T5With DisplayIIB cover: Ex d [ia/ib] IIB + H2 T5IIC cover: Ex d [ia/ib] IIC T5

This unit is provided with an internal and external terminal for supplementary bonding connection. This terminal is for use where local codes or authorities permit or require such connection.

For proper installation including I/O, power, gland and hazardous area

location, refer to appropriate 1700/2700/2750 output option ATEX-D-

IS installation instructions

RS48

5ARS

485b

COMBINE THIS DRAWING WITH ONE OF FIGURE 2, 3, 4, OR 5

1. The total Ci is equal to the sum of all Ci values of all devices on the network. Ccable is the total capacitance of all cable on the network.

2. The total Li is equal to the sum of all Li values of all devices on the network. Lcable is the total inductance of all cable on the network.

3. If the electrical parameters of the cable are unknown, then the following values may be used:Cable Capacitance = 197pF/mCable Inductance = 0,66H/m

4. This device must not be connected to any associated apparatus which uses or generates more than 250Vrms with respect to earth ground.

5. Maximum cable length determined by entity parameters and maximum cable inductance.

Installation notes:

Associated apparatus parameter limits

Reference no. EB-20003015 Rev. A



Figure 2: CMF sensor with enhanced core processor

Figure 3: CMF, D (except D600), DL, F, H, R, CNG and T sensors with core processor

COMBINE THIS DRAWING WITH FIGURE 1

I.S.cable

See note 5.

Hazardous Area Ex ib IIC / IIB

Refer to sensor tag for complete hazardous area classification.

Sensor mounted enhanced core processor

4-wire I.S. and non-incendive core processor entity parameters

Internal ground

Externalground

VdcVD

C +

VDC

R

S485

AR

S485

B

Reference no. EB-20003015 Rev. A



I.S.cable

See note 5.Hazardous Area EEx ib IIC / IIB

Refer to sensor tag for complete hazardous area classification.

Sensor mounted core processor


Vdc

VDC

VDC+


Reference no. EB-3600583 Rev. F





Figure 4: D600 with core processor

Figure 5: Remote core processor with remote transmitter

Hazardous AreaEEx de [ib] IIB T4Refer to sensor and booster amplifier tags for complete hazardous area classification. Core

processor mounted on

sensor booster amplifier


Vdc

VDC

VDC+


Maximum cable length determined by entity parameters and maximum cable inductance.

I.S.cable

Installation method Fitting required

Per EN6007914

Conduit EEx d IIB Conduit Seal

Cable EEx d IIB Cable GlandConduit or Cable Increased Safety EEx e

1/2"14 NPT or M20 1,5 adaptersupplied as ordered

Conduit Seal Required within 18" of enclosure. To besealed after wiring. (customer supplied)

Power

Ground chassis

To drive coil located in sensor

VAC

To achieve potential equalization the groundterminal must be connected to the appropriate

ground terminal within the hazardous areausing a potential equalizing line.

For remote mount booster amplifier wiring see drawing EB-1005122

Explosion-Proof housing


Reference no. EB-1005121 Rev. C

VDC +

Hazardous Area EEx ib IIB / IIC

Refer to remote core processor tag for complete hazardous area classification.

Ground screwBlack

9-wireIS cable

20 m. maximum cable length

Remote core processor

Maximum cable length determined by entity parameters and maximum cable inductance.

4-wireIS cable

VDC

RedGreenWhite

BlueGrayOrange

BrownViolet

Yellow

Ground screw

4-wire and non-incendive core processor entity parameters

Vdc

COMBINE THIS DRAWING WITH FIGURE 1 AND ALSO WITH ONE OF FIGURE 7, 8, OR 9




Figure 6: 1700/2700/2750 transmitter with integral core processor

COMBINE THIS DRAWING WITH ONE OF FIGURE 7, 8, OR 9

(WARNING: SUBSTITUTIONS OF COMPONENTS MAY IMPAIR INTRINSIC SAFETY)

Ground screw

RedGreenWhite

Ground screw

BrownViolet

Yellow

BlueGrayOrange

Black


Refer to Model Number on 1700/2700/2750 transmitter tag for specific hazardous location.

* Increased Safety version:No DisplayEx de [ia/ib] IIC T5With DisplayIIB cover: Ex de [ia/ib] IIB + H2 T5IIC cover: Ex de [ia/ib] IIC T5

* Flameproof version:No DisplayEx d [ia/ib] IIC T5With DisplayIIB cover: Ex d [ia/ib] IIB + H2 T5IIC cover: Ex d [ia/ib] IIC T5

For proper installation of I/O, power and ground terminals, refer to appropriate ATEXDIS installation drawing

9-wireIS

cable




Figure 7: CMF, D (except D600), DL, F, H, and T sensor with junction box

Figure 8: D600 with junction box

COMBINE THIS DRAWING WITH ONE OF FIGURE 5 OR 6

Refer to sensor tag for complete hazardous area classification


9-wireIS

cable20 m. maximum

cable length

BlueGrayRed

Sensor junction box

VioletYellow

OrangeChassisground

Sensor junction box

Chassis ground

Refer to sensor tag for complete hazardous area classification

ModelD, DL

(EXCEPT D600)Supplied as intrinsically safe

ModelCMF T F H

Supplied as intrinsically safe

Hazardous AreaEEx ib IIB / IIC

Hazardous AreaEEx ib IIB / IIC

GreenWhiteBrown

9-wireIS

cable

BrnRedOrnYelGrnBluVioGryWht


Reference no. EB-1005123 Rev. B

Hazardous Area EExde [ib] IIB

Installation method Fitting required

Per EN6007914

Conduit EEx d IIB conduit seal

Cable EEx d IIB cable glandConduit or cable increased safety EEx e

Cable O.D. must be suitably sized to gland.Intrinsically safe

terminals

To achieve potential equalization the ground terminal mustbe connected to the appropriate ground terminal within the

hazardous area using a potential equalizing line.

Micro Motion mass flowmeter system connection for intrinsically safe operation

VioletYellow

Orange

GreenWhiteBrown

BlueGrayRed

1/2"14 NPT orM20 1.5 adapter supplied as ordered

Conduit seal required within 18" ofenclosure. To be sealed after wiring

(customer supplied).Power

Ground chassis

To drive coil located in

sensor

20 m maximum

cable length

IS cable

For remote mount booster amplifier wiring refer to EB-3007062.

CAUTION:To maintain intrinsic safety, the intrinsically safe wiring must be installed according to EN 60079-14. Transmitter and sensor must be properly grounded.

VAC




Figure 9: DT with junction box

Models: DT65, DT100, DT150

DT sensor wire terminations to IS cable

DT sensor wire # IS cable color1 Brown2 Red3 Orange4 Yellow5 Green6 Blue7 Violet8 Gray9 White

Hazardous AreaEEx ib IIb

9-wireIS

cable

20 m maximumcable length

Special conditions for safe use:For the sensor types DT065, DT100, and DT150 the following applies: The minimum medium temperature is +32 C.

DT sensor wires must be connected to IS cable using customer supplied terminal block and

junction box.

Earth ground

DT sensor wires

Micro Motion mass flowmeter system connection for intrinsically safe operation


Reference no. EB-20000081 Rev. B



Figure 10: Transmitter outputs (WARNING: SUBSTITUTIONS OF COMPONENTS MAY IMPAIR INTRINSIC SAFETY)

Refer to Model Number on 1700/2700/2750 transmitter tag for specific hazardous location.

Increased safety version:No DisplayEx de [ib] IIC T5With DisplayIIB cover: Ex de [ib] IIB + H2 T5IIC cover: Ex de [ib] IIC T5

Flameproof version:No Display

Ex d [ib] IIC T5With DisplayIIB cover: Ex d [ib] IIB + H2 T5IIC cover: Ex d [ib] IIC T5

Note: Hazardous area classification on an integrally mounted 1700/2700/2750 transmitter can be limited by hazardous area classification of the sensor. Refer to sensor tag.

If the ambient temperature is40 C to 20 C, use cable and cable entries or conduit entries certified for this condition.If certified conduit entries are used, install the associated stopping boxes immediately at the sensor enclosure.

This unit is provided with an external terminal for supplementary bonding connection. This terminal is for use where local codes or authorities permit or require such connection.Equipment ground

(For temporary diagnostic use only)

VDCVAC

USP+USP

1

Model 1700/2700/2750 terminal configurationTerminal Analog

*700*1*A***Intrinsically safe*7*0*1*D***

Config I/O2700*1*B***

Fieldbus27*0*1*E*** or2700*1*N***

PROFIBUS-PA27*0*1*G***

1 I/O 1+ mA / HART + mA1 / HART + mA1 / HART + Channel A Fieldbus + PROFIBUS +2 I/O 1 mA / HART mA1 / HART mA1 / HART Channel A Fieldbus PROFIBUS 3 I/O 2+ FO + FO + mA2 / DO1 / FO + Channel B4 I/O 2 FO FO mA2 / DO1 / FO Channel B5 I/O 3+ RS-485 A mA2 + FO / DO2 / DI + Channel C6 I/O 3 RS-485 B mA2 FO / DO2 / DI Channel C

Model 1700/2700/2750 intrinsic safety parametersIntrinsically safe*7*0*1*D***

Fieldbus27*0*1*E*** or2700*1*N***

PROFIBUS-PA27*0*1*G***

Terminals1 & 2 and 5 & 6

Terminals 3 & 4 Terminals 1 & 2 Terminals 1 & 2

Vmax (Vdc) 30 30 33 33Imax (mA) 300 100 380 380Pmax (W) 1,0 0,75 5,32 5,32Ci (F) 0,0005 0,0005 Negligible NegligibleLi (H) 0,0 0,0 Negligible Negligible

2

3

4

5

6

Micro Motion Inc. USAWorldwide Headquarters7070 Winchester CircleBoulder, Colorado 80301T +1 303-527-5200

+1 800-522-6277F +1 303-530-8459

Micro Motion EuropeEmerson Process ManagementNeonstraat 16718 WX EdeThe NetherlandsT +31 (0) 318 495 555F +31 (0) 318 495 556

Micro Motion JapanEmerson Process Management1-2-5, Higashi ShinagawaShinagawa-kuTokyo 140-0002 JapanT +81 3 5769-6803F +81 3 5769-6844

Micro Motion AsiaEmerson Process Management1 Pandan CrescentSingapore 128461Republic of SingaporeT +65 6777-8211F +65 6770-8003

Micro Motion United KingdomEmerson Process Management LimitedHorsfield WayBredbury Industrial EstateStockport SK6 2SU U.K.T +44 0870 240 1978F +44 0800 966 181

2008, Micro Motion, Inc. All rights reserved. P/N MMI-20011705, Rev. A

*MMI-20011705*

For the latest Micro Motion product specifications, view the PRODUCTS section of our web site at www.micromotion.com

/ColorImageDict > /JPEG2000ColorACSImageDict > /JPEG2000ColorImageDict > /AntiAliasGrayImages false /CropGrayImages true /GrayImageMinResolution 300 /GrayImageMinResolutionPolicy /OK /DownsampleGrayImages true /GrayImageDownsampleType /Bicubic /GrayImageResolution 300 /GrayImageDepth -1 /GrayImageMinDownsampleDepth 2 /GrayImageDownsampleThreshold 1.50000 /EncodeGrayImages true /GrayImageFilter /DCTEncode /AutoFilterGrayImages true /GrayImageAutoFilterStrategy /JPEG /GrayACSImageDict > /GrayImageDict > /JPEG2000GrayACSImageDict > /JPEG2000GrayImageDict > /AntiAliasMonoImages false /CropMonoImages true /MonoImageMinResolution 1200 /MonoImageMinResolutionPolicy /OK /DownsampleMonoImages true /MonoImageDownsampleType /Bicubic /MonoImageResolution 1200 /MonoImageDepth -1 /MonoImageDownsampleThreshold 1.50000 /EncodeMonoImages true /MonoImageFilter /CCITTFaxEncode /MonoImageDict > /AllowPSXObjects false /CheckCompliance [ /None ] /PDFX1aCheck false /PDFX3Check false /PDFXCompliantPDFOnly false /PDFXNoTrimBoxError true /PDFXTrimBoxToMediaBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXSetBleedBoxToMediaBox true /PDFXBleedBoxToTrimBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXOutputIntentProfile () /PDFXOutputConditionIdentifier () /PDFXOutputCondition () /PDFXRegistryName () /PDFXTrapped /False

/CreateJDFFile false /Description > /Namespace [ (Adobe) (Common) (1.0) ] /OtherNamespaces [ > /FormElements false /GenerateStructure false /IncludeBookmarks false /IncludeHyperlinks false /IncludeInteractive false /IncludeLayers false /IncludeProfiles false /MultimediaHandling /UseObjectSettings /Namespace [ (Adobe) (CreativeSuite) (2.0) ] /PDFXOutputIntentProfileSelector /DocumentCMYK /PreserveEditing true /UntaggedCMYKHandling /LeaveUntagged /UntaggedRGBHandling /UseDocumentProfile /UseDocumentBleed false >> ]>> setdistillerparams> setpagedevice

atex installation instructions

Documents