PARTNO.

DESCRIPTION PART Q’TY

1

2

3

4

5

6

7

8 4

4

2

2

4

1

1

1

1

2

2

2

22

9

10

11

12

13

14

15

16

KTS233W-CS01

62KTS233WI101

62KUS2310B201

KTS233W-CS03

62KUS2310H101

180703010501

17XA1002-----Y3 17XA1009-----Y3

2KTS233W-CS02

4

17KAA0201----Y4

217

61K233WK00001BA

61K233WA00001BA

180706010302

17FA08070601-Y4

18060608081201

17C01A0835011Y4

17XA0901-----Y3

Use the correct bolts as indicated. Do not tighten any of the bolts until is completely assembled.

Do not discard of any of the packaging until you have checked that you have all of the parts and fittings required.

Keep children away during assembly. This item contains small parts that can be swallowed by children. Children should always be under direct adult supervision while using this product.

Retain these assembly instructions for future reference.

Quote the following FQC NO. when contacting the service center. SERVICE CENTER TOLL FREE NO. TEL: 1-877-539-7436 FAX: 1-877-539-7439

!

!

!

!

!

PAGE 1 OF 4

PARTS LIST

STOP DON’T RETURN TO STORE!

ASSEMBLY INSTRUCTIONSATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE INTENDED FOR RESIDENTIAL USE ONLY.

KTS233W-WM

COURTYARD CREATIONS INC.

SIDE SUPPORT A

SIDE SUPPORT B

CROSS BRACE

SIDE BEAM

BOTTOM SUPPORT

BRACE

BRACE CAP

5 LINK SUSPENSION CHAIN 6 LINK SUSPENSION CHAIN

HEX.KEY WRENCH 6MM

PILLOW

FABRIC

PLASTIC END CAP

WASHER d8.5*D21*1.6

WASHER d10.5*D32*4

BOLT M8*105

CHAIN CONNECTOR

FIGURE 1

5

5

5

5

5

5

5

11

2

25

5

53

5

3

5

3

10121113

5

5

Step 4: Press the spring buttons on the bottom supports (#5) and insert into the side supports A (#1) and the side supports B(#2). Make sure that the spring buttons on the bottom supports (#5) come completely through the holes on the side supports A (#1) and the side supports B (#2). See Figure 4.

Step 3: Secure the safety locks on all sides of the bottom supports (#5). See Figure 3.

Step 2: Insert bolt (#10) with washer (#12) through the outside bottom support (#5). Then, place washer (#11) onto the bolt and insert through the inside bottom support (#5). Place a plastic end cap (#13) onto the bolt and screw into the cross brace (#3). Repeat the same procedure for both sides. See Figure 2.

Step 1: Position two bottom supports (#5) together facing in opposite directions. See Figure 1.

Note: The labelled arrows on the bottom supports (#5) should be facing each other as displayed in Figure 1.

FIGURE 2

FIGURE 3

FIGURE 4

PAGE 2 OF 4STOP DON’T RETURN TO STORE!

Step 5: Press the spring buttons on the side supports A (#1) and the side supports B (#2) and insert into the side beams (#4). Make sure that the spring buttons on the side supports(#1) come completely through the holes on the side beams (#4). See Figure 5.

Step 6: Attach the 4-link suspension chains (#17) onto the chain connectors (#9). Insert the braces (#6) into the sleeves of the fabric (#14). Place the chain connectors (#9) onto the braces (#6) where there are slits. See Figure 6.

Step 7: Place the brace caps (#7) onto the ends of the braces (#6).See Figure 7.

Step 8: Hang the 4-link suspension chains (#17) that are already attached to the braces (#6) onto the hooks located on the side beams (#4). See Figure 8.

STOP DON’T RETURN TO STORE!

FIGURE 5

FIGURE 7

FIGURE 8

PAGE 3 OF 4

FIGURE 6

11

4

4

4

89

4

2

14

14

6

67

6

2

9

17

STOP DON’T RETURN TO STORE!

FIGURE 10

FIGURE 9

17

17

154

4

Step 9: Hang the 6-link suspension chains (#17) to the hooks on one of the side beams (#4). Tie the pillow (#15) to the suspension chains (#8) at the higher side of the hammock. See Figure 9.

Note: The 6-link suspension chains (#17) are to be used when the hammock is folded closed.

To Fold The Hammock:Step 1: Release the safety locks on the bottom supports (#5). See Figure 10.

Step 2: Fold the hammock and secure in place by hooking the 6-link suspension chains (#17) to the opposite side beams (#4). See Figure 11.

Cleaning and Maintenance • Wash frame parts with mild soap and water, rinse thoroughly, and dry completely. Do not use bleach, acid, or other solvents on the frame parts.• The pillow, fabric, and magazine bag may be washed on the surface only by using mild soap and water or commercial foaming upholstery cleaner if necessary. If washed, rinse well, and hang to dry. Do not machine wash or dry.• We recommend the use of furniture covers when not in use.• Inspect and tighten all bolts and fasteners on a regular basis to ensure proper performance and safety of your hammock.• In order to prolong the life and beauty of your hammock, we recommend that it be stored in a dry and protected area during off season periods.

Note: Before each use, inspect the hammock to ensure that all parts are in good order and are properly assembled. Carefully examine the frame to ensure that all parts (including welds) are sound (free of excessive rust or cracks).

Note:Two people are needed to open and fold this hammock.Please hold the hammock at the top when opening and closing.

FIGURE 11

PAGE 4 OF 4

The store where you made your purchasedoes not stock parts for this item.

If you need parts,whether they are missing or damaged,

STOP!Missing A Part?

No Need To Go Back ToThe Store

Call us between 9:00 AM and 4:30 PMEastern Time Monday through Friday

Call Toll Free:TEL: 1-877-539-7436FAX: 1-877-539-7439

READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING ASSEMBLY SEPARATE AND IDENTIFY ALL PARTS, MAKING SURE THAT YOU HAVE ALL OF THE PARTS LISTED.IF YOU DO NOT LOCATE ALL OF THE PARTS LISTED, INSPECT THE PACKING MATERIAL FOR SMALL PARTS THAT MAY HAVE BECOME SEPARATED DURING SHIPMENT.IF YOU EXPERIENCE ANY DIFFICULTY DURING ASSEMBLY OR IF ANY PARTS ARE MISSING OR DAMAGED, CALL THE HELP LINE AT 1-877-539-7436 BEFORE RETURNING THIS ITEM TO THE STORE.PROVIDE THE FOLLOWING INFORMATION WHEN CALLING:1-MODEL NUMBER OF THE PRODUCT.2-PART NUMBER AND MATERIAL CODE OF THE PART FROM THE PARTS LIST.MOST PROBLEMS CAN BE RESOLVED WITHOUT RETURNING THIS PRODUCT TO THE RETAILER.