aso eent shed model: 30372…absco industries assembly instruction manual aso eent shed model: 30372...
TRANSCRIPT
Absco Industries Assembly Instruction Manual
ABSCO REGENT SHEDMODEL: 30372RK3.00mW x 3.66mD x 2.10mH
Model: 30372RK 19/09/18 1.4 1
Download the Absco Sheds Assembly App for instructional videos
MANU FA CT UREDIN A US TR ALIA
SNAPTiTEAssemb ly
AU: 1800 029 701N Z: 0800 466 444
When laying concrete slab, ensure there is a rebated edge 25mm deep around the perimeter. This will help water egress from the base of the shed.
For construction in non-cyclonic areasWind rating: N2 as per AS4055-2012
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION MANUAL SHED MODEL: 23151GK 21-11-2017
CONCRETE SLAB
2360mm1620mm
FRONT: 2.26mSIDE: 1.52mHEIGHT: 1.95m
We thank you for choosing an Australian madeshed. For further assistance please visit our detailed
instructional video library atHttp://www.abscosheds.com.au/watch-videos
At ABSCO Industries we are always looking to benumber ONE, so please let us know what you think
of our instructions. Feedback makes us [email protected]
CONCRETE
REBATED EDGEBOTTOM CHANNEL
CONCRETE SLAB
75mm WIDE REBATE
100mm
WHEN LAYING YOUR CONCRETESLAB, ENSURE THERE IS A
REBATED EDGE 25mm DEEPAROUND THE PERIMETER
THIS WILL HELP WATER EGRESSFROM THE BASE OF THE SHED
Absco IndustriesPremier Shed Model: 23151GK
PAGE 01
CONCRETE SLAB
3100mm
3760mm
Absco Industries Assembly Instruction Manual
ABSCO REGENT SHEDMODEL: 30372RK3.00mW x 3.66mD x 2.10mH
Model: 30372RK 19/09/18 1.4 2
GENERAL INSTRUCTIONS
• Before commencing any assembly, read through these instructions in detail to gain a thorough understanding of assembly methods and associated details.
• Unpack the carton and carefully identify and check off all the parts against the parts described and illustrated on "COMPONENTS PACKING LIST" pages.
SITE PREPARATION
• The site for the shed must be level. An uneven surface may result in misalignment of parts.
• The shed shall be erected on top of a reinforced concrete slab and anchored down appropriately illustrated on “FINAL CONSTRUCTION” page.
TOOLS REQUIRED
SAFETY NOTES
• Some parts may have sharp edges. It is advisable to wear gloves when handling these items and safety glasses if drilling holes. Sensible shoes are highly recommended.
• Do not erect your shed in windy conditions.
• Ensure that the shed is securely anchored to a solid foundation immediately after construction is completed.
• It is highly recommended to erect the shed with two or more people.
RECOMMENDED
3mm
dril
l bit
10m
m d
rill b
itm
etal
/mas
onr
y
Absco Industries Assembly Instruction Manual
ABSCO REGENT SHEDMODEL: 30372RK3.00mW x 3.66mD x 2.10mH
Model: 30372RK 19/09/18 1.4 3
COMPONENT PACKING LIST
Check off all components.
COMPONENTDESCRIPTION
PARTNo. CHECK COMPONENT
DESCRIPTIONPART
No. CHECKQTY QTY
2
8
2
2
6
2
4
1
1
2
STEEL SHEET1785mm X 711mm 34A
STEEL SHEET1785mm X 731mm 32A
STEEL SHEET1725mm X 773mm A
STEEL SHEET1725mm X 773mm B
GABLE L/HL=1475mm 16L
GABLE R/HL=1475mm 16R
13ABRACEL: 393mm
97DL1 RIDGEBEAM
1
L = 1866.5mm
97DRRIDGEBEAM
ZARSP1 RIDGE BEAM JOINERL: 450mm
L = 1866.5mm
1785mm X 773mm 30ASTEEL SHEET
STEEL SHEET1785mm X 773mm 31A
STEEL SHEET1546mm X 773mm 44L
STEEL SHEET1546mm X 773mm 44R
STEEL SHEET1546mm X 773mm 45A
2 2
Absco Industries Assembly Instruction Manual
ABSCO REGENT SHEDMODEL: 30372RK3.00mW x 3.66mD x 2.10mH
Model: 30372RK 19/09/18 1.4 4
COMPONENT PACKING LIST
1 479ACHANNELL = 1568mm
58ACHANNEL WITH HINGESL = 1725mm
58BCHANNELL = 1725mm
58CCHANNELL = 773mm
77AL
55CL
77BL
81BL
81LL
62BL
55CR
1
1
1
1
2
2
1
1
1
1
2
2
CHANNELL = 1496.5mm
CHANNELL = 1496.5mm
CHANNELL = 1496.5mm
CHANNELL = 1496.5mm
CHANNELL = 1866.5mm
CHANNELL = 1866.5mm
77BR
81BR
81LR
62BR
77ARCHANNELL = 1496.5mm
CHANNELL = 1496.5mm
CHANNELL = 1496.5mm
CHANNELL = 1496.5mm
CHANNELL = 1866.5mm
CHANNELL = 1866.5mm
COMPONENTDESCRIPTION
PARTNo. CHECK COMPONENT
DESCRIPTIONPART
No. CHECKQTY QTY
81KL2 2CHANNELL = 1829.5mm
81KRCHANNELL = 1829.5mm
62AL2 2CHANNELL = 1829.5mm
62ARCHANNELL = 1829.5mm
58C
58B58A
79A
77AL
JOIN>>
55CLJOIN>>
77BL
JOIN>>
81BLJOIN>>
81LL
JOIN>>
62BLJOIN>>
81KLJOIN>>
62ALJOIN>>
62AR
JOIN>>
81KR
JOIN>>
62BR
JOIN>>
81LR
JOIN>>
81BR
JOIN>>
77BR
JOIN>>
55CR
JOIN>>
77AR
JOIN>>
12
Absco Industries Assembly Instruction Manual
ABSCO REGENT SHEDMODEL: 30372RK3.00mW x 3.66mD x 2.10mH
Model: 30372RK 19/09/18 1.4 5
COMPONENT PACKING LIST
1
12A2DOORSTRAPL: 6.5"
14A2 CAP GABLEL: 170mm 1 ASSEMBLY
INSTRUCTIONS
COMPONENTDESCRIPTION
PARTNo. CHECK COMPONENT
DESCRIPTIONPART
No. CHECKQTY QTY
INSTRUCTIONS & FITTINGS PACKET
4
4
1
2 89AJAMB L= 1785mm
90AJAMB L= 1568mm
91AJAMB L= 1120mm
89CJAMB L= 1725mm
87BLIP TRIM L= 1546mm
CSJ12 CHANNEL JOINERL= 200mm
Part No. Here
Part No. Here
Part No. Here
Part No. Here
87B
CSJ
DOORPADBOLT
HASP23
SELF TAPPING SCREWSPACKET CONTAINING 2201
DOORPADBOLT
3/16 COUNTERSUNKSCREWS & NUTS12
3/16 ROUND HEADBOLTS & NYLOCK NUTS8 3.2 x 8mm
BLIND POP RIVETS12
PSTKDBL - DOUBLE DOOR FITTINGS PACK
PACK12P - SCREW PACK 12
PACK12PSCREW PACK 121
PHILLIPS DRIVER BIT3mm DRILL BIT DRILL FAST038
FAST007FAST006
10 16mm TEKSCREWS FAST014
11
11
SELF TAPPING SCREWSPACKET CONTAINING 100
PSTKDBLDBL DOOR FITTINGS PACK
Absco Industries Assembly Instruction Manual
ABSCO REGENT SHEDMODEL: 30372RK3.00mW x 3.66mD x 2.10mH
Model: 30372RK 19/09/18 1.4 7
SNAPTiTE ASSEMBLY GUIDE
The Snaptite Assembly System locks end channels to all roof and wall sheets without the need for tools and fasteners.
To assemble each panel, the perimeter channels are secured to the top and bottom of each panel.Gently tap the channel over the SNAPTiTE lugs on the sheet, working along the sheet.
Each perimeter channel must fi nish fl ush with the edges of the sheets. Simply tap the channel along the sheets until each end is neatly fl ush. If you need to remove channels from the panels, slide it off from the side.
Channel locks the shed panel into position without the need for screws!
FASTENING SYMBOLS
Secure channel to sheeting by SNAPTiTE fastening method.
Join components together with one screw at this location only, as some channels have extra holes that are not required for this model of shed.
Do not join components together at this location yet, as the screws may obstruct further assembly of the other components.
Join components together by pre-drill-ing the holes fi rst. Use one component as template to mark where the holes are and drill with a 3mm drill bit.
3mm pop rivet
4mm nut and bolt set.
DSNAPT TEi
Absco Industries Assembly Instruction Manual
ABSCO REGENT SHEDMODEL: 30372RK3.00mW x 3.66mD x 2.10mH
Model: 30372RK 19/09/18 1.4 8
Guide on Joining Spliced ChannelsThe text marked on all parts must be shown on the same side as each other
Step 1.Position the channels and the CSJ joiner so the centre of the CSJ is in line with the end of each channel to be joiner together.
Step 2.Join the fi rst channel to the CSJ by inserting the centre of the CSJ, on an angle, to the end of the channel where the JOIN>> text is marked.
Push down one side of the CSJ until you hear a ‘click’.
Step 3.Join the second channel to the CSJ by positioning the <<JOIN of the channel at the centre of the CSJ, on an angle. Push the CSJ into the channel until you hear a ‘click’.
Finished Channel.The joined channels should now look like the picture with the CSJ positioned equally inside of the joined channels.
Drill out holes with 3mm drill bit in CSJ to match the holes in channel and secure with the screws supplied.These may have to be temporarily removed during assembly.
= =
JOIN>> <<JOIN
CSJ
=
=
JOIN>> J
==
JOIN>> SJ
= =
JOIN>><<JOIN
= =
JOIN>> <<JOIN
Finished Spliced Channel
Channel
Push
20mm 15mm
CSJ.
...
Absco Industries Assembly Instruction Manual
ABSCO REGENT SHEDMODEL: 30372RK3.00mW x 3.66mD x 2.10mH
Model: 30372RK 19/09/18 1.4 9
PRE-ASSEMBLY OF SPLICED CHANNELS
NOTE: Some channels may have holes in them - You will need to redrill holes where CSJ joining channel covers them.
Join together 24 x channel sections using 12 x channel joiners (Part CSJ)
=
=
=
=
=
1 X 77BR
2993mm
1 x 77A
1 x 77B
1 x 55C
2 x 62B
1 x 81B
81BR
81BL
62BL
62BR
55CR
55CL
77AR
1 X 77AR1 X 77AL
1 X 77BL
1 X 55CR1 X 55CL
2 X 62BR2 X 62BL
1 X 81BR1 X 81BL
=
2 X 81LR
2 x 81L
81LR
81LL
2 X 81LL
3733mm
77BL
77BR
77AL
= 2 x 62A
62AL
62AR
2 X 62AR2 X 62AL
=
2 X 81KR
2 x 81K
81KR
81KL
2 X 81KL
3659mm
Absco Industries Assembly Instruction Manual
ABSCO REGENT SHEDMODEL: 30372RK3.00mW x 3.66mD x 2.10mH
Model: 30372RK 19/09/18 1.4 10
Tek screw driver bit
Push
Guide on Joining a Spliced Ridge BeamFollow these three steps to assemble a ridge beam.
Step 1.Place two ridge beams as shown and push them together. Slide the cap of one under the other.
NOTE.There is a 50mm overlap of the ridge caps when the beams are in position.
Step 2.Use the ZARSP to connect at the centre of the two ridge beams. Be sure it is pushed in fully.
Step 3.Turn over the ridge beam. Measure 250mm from the middle along the centre of one ridge beam, mark spacings of 50mm. Fasten with a Tek screw at each marking.
Repeat to the other side of the ridge beam assembly.
TIP: Predrilling each hole with the 3mm drill bit makes it easier to fasten.
50mm225mm
ZARSP
Finished Spliced Ridge Beam
FinishedSpliced Ridge Beam
ZARSP
Ridge Beam
Self drilling Tek screw
Absco Industries Assembly Instruction Manual
ABSCO REGENT SHEDMODEL: 30372RK3.00mW x 3.66mD x 2.10mH
Model: 30372RK 19/09/18 1.4 11
PRE-ASSEMBLY OF SPLICED RIDGE BEAM
.
.
1x 97DL 1x 97DR
= 1x 97D
3733mm Overall length
ZARSP
225mm
97DL
97DR
16mm
16mm
Absco Industries Assembly Instruction Manual
ABSCO REGENT SHEDMODEL: 30372RK3.00mW x 3.66mD x 2.10mH
Model: 30372RK 19/09/18 1.4 12
OVERVIEW OF ROOF COMPONENTS
OV
ER
VIE
W O
F R
OO
F C
OM
PO
NE
NTS
44R
45A
45A
45A
44L
44R
45A
45A
45A
44L
81L
87B
14A
87B
97D
81L
62B
87B
87B
Absco Industries Assembly Instruction Manual
ABSCO REGENT SHEDMODEL: 30372RK3.00mW x 3.66mD x 2.10mH
Model: 30372RK 19/09/18 1.4 13
OVERVIEW OF WALL COMPONENTS
OV
ER
VIE
W O
F W
ALL
CO
MP
ON
EN
TS
32A
31A
31A
31A
32A
81K
91A 91
A
89A
90A
34A
A
B
34A
55C
79A
89A
22A
62A
77B
16R
81B
30A
13A
31A
31A
30A
32A
31A
31A
31A
32A
62A
16R
77A
13A
16L
81K
16L
Absco Industries Assembly Instruction Manual
ABSCO REGENT SHEDMODEL: 30372RK3.00mW x 3.66mD x 2.10mH
Model: 30372RK 19/09/18 1.4 14
REAR PANEL ASSEMBLY
1x required.
30A
31A
31A
30A
81B
SNAPT
TEi
SNAPT TEi
77B
Absco Industries Assembly Instruction Manual
ABSCO REGENT SHEDMODEL: 30372RK3.00mW x 3.66mD x 2.10mH
Model: 30372RK 19/09/18 1.4 15
ROOF PANEL ASSEMBLY
2x required.
Fit 81L to edge of sheet with pre-punched holes.
44L
45A
45A
45A
44R
87B
81L
62B
SNAPT TEi
SNAPT TEi
87B
Absco Industries Assembly Instruction Manual
ABSCO REGENT SHEDMODEL: 30372RK3.00mW x 3.66mD x 2.10mH
Model: 30372RK 19/09/18 1.4 16
SIDE PANEL ASSEMBLY
2x required.
62A
81K
SNAPT TEi
SNAPT TEi
SMALL PAN
SMALL PAN
32A
31A
31A
31A 32A
Absco Industries Assembly Instruction Manual
ABSCO REGENT SHEDMODEL: 30372RK3.00mW x 3.66mD x 2.10mH
Model: 30372RK 19/09/18 1.4 17
FRONT PANEL ASSEMBLY
89A
89A
34A1x required.
34A
77A
90A
79A
55C
SNAPT TEi
SNAPT TE
i
SNAPT TEi
SNAPT TEi
Absco Industries Assembly Instruction Manual
ABSCO REGENT SHEDMODEL: 30372RK3.00mW x 3.66mD x 2.10mH
Model: 30372RK 19/09/18 1.4 18
DOOR PANEL ASSEMBLY
58C
58C
58C
12A
58C
58A
58A
A
B
89C
58B
A
B
SNAPT TEi
SNAPT TEi
SNAPT TEi
SNAPT TEi
Vertical door channels are installed in the opposite orientation compared to the horizontal door channels.
Four hole set for padbolt connection.
Short fl ange of channel
Long fl ange of channel
D
D
D
D
D
D
D
D
1x required.
Absco Industries Assembly Instruction Manual
ABSCO REGENT SHEDMODEL: 30372RK3.00mW x 3.66mD x 2.10mH
Model: 30372RK 19/09/18 1.4 19
DOOR PANEL ASSEMBLY
Nuts and bolts may be used instead of pop rivets by drilling out hinge holes using a 4mm drill bit. Both are supplied.
The two holes required to connect the padbolt hasp for each door have not been pre-punched, to allow for proper alignment, position each hasp centrally over the padbolt shaft and drill 3mm holes and secure with screws.
91A
91A
A
B
Absco Industries Assembly Instruction Manual
ABSCO REGENT SHEDMODEL: 30372RK3.00mW x 3.66mD x 2.10mH
Model: 30372RK 19/09/18 1.4 21
PANEL CONSTRUCTION
NOTE: Take care to ensure that all wall panels are not upside down. The top channels of each panel are pre-punched for attaching roof sheeting. The base channels are not pre-punched.
Pre-punched channel to match ridge beam holes
Side wall channels fit into the notched rear wall channels.
Pre-punched holes in roof panel to
this side
for connection to fro
nt and rear walls.
Orient panel so channel (62B) goes into ridge beam
Channel (81L) this end
97D
D
D
D
D
D
D
D
D
D
D
D
D
D
DD
DDD
D
D
DD
D
DDD
D
Absco Industries Assembly Instruction Manual
ABSCO REGENT SHEDMODEL: 30372RK3.00mW x 3.66mD x 2.10mH
Model: 30372RK 19/09/18 1.4 22
INSIDE VIEW OF FIXING
INSIDE VIEW OF FRONT WALL
OUTSIDE VIEW
37mm
ROOR OVERHANGSALL WALL PANELSBY 37mm
13A
Secure ridge beam to gable sections with two screws at each end. Secure each roof panel with one screw in each corner only at this stage
After attaching both roof panels to walls as shown above, fit one regent brace to the ridge beam and front wall as shown. You will have to remove and replace existing screws at fixing locations. Repeat this procedure for the rear wall regent brace
Absco Industries Assembly Instruction Manual
ABSCO REGENT SHEDMODEL: 30372RK3.00mW x 3.66mD x 2.10mH
Model: 30372RK 19/09/18 1.4 23
FINAL CONSTRUCTION
Each anchor consists of one nut, bolt, M10 dynabolt and steel angle.Drill a 10mm hole into the wall sheet.Drill a 10mm hole into the concrete.
Bolt and Nut*M10 4.6/S
Steel Angle*35 x 35 x 3
M10 Dynabolt*
* Denotes hot dip galvanised fi nish
Wall Sheet
Slab
14A
Bend the top and bottom flanges as shown, then hook the bottom flanges under the top channel and screw top to the ridge beam with two screws.
ANCHORING OF SHED
Location of 16concrete anchors
250
250
250
250
1000
1000
700
700
640
640
640
640
640
640
640
640
640
640
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
DD
D
D
DD
D
Absco Industries Assembly Instruction Manual
ABSCO REGENT SHEDMODEL: 30372RK3.00mW x 3.66mD x 2.10mH
Model: 30372RK 19/09/18 1.4 24
Absco Gable Roof Shed Notes
• 1.G This instruction manual shall be read in conjunction with other consultants drawings, specifi cations and written instructions provided by Absco and/or their representatives.
• 2.G The drawings provided herein are for installation and structural engineering purposes only.
• If discrepancies are discovered within the documentation provided, these shall be brought to the attention of Absco and written approvals obtained prior to commencing the affected section of work.
• 3.G If in doubt ask.
• 4.G Until approvals from the local authorities are obtained, commencement of construction from these drawings shall not commence.
• 5.G Unless varied by the project specifi cation, all materials and workmanship shall be undertaken in accordance with the relevant Australian standards and the by-laws and ordinances of the relevant building authorities.
• 6.G All dimensions indicated in these drawings shall be verifi ed on site by the installation contractor. Scaling of drawings shall not be undertaken.
• 7.G Prior to commencing works on site, the contractor shall verify the position of all services in the area to ensure that the construction does not interfere with any of those services.
• 8.G During installation on site the shed structures shall be maintained in a stable condition with no part becoming overstressed or permanently deformed.
• 9.G In circumstances where the shed has been installed in a manner which is inconsistent with the installation manual, structural certifi cation shall be void.
• 10.G The structural components detailed within this installation manual have been designed for the following loads in accordance with AS/NZS1170 based on a Class 10a, Type 2 structure:
• Roof Live Load: 0.25 kPa uniformly distributed or 1.1 kN concentrated as per AS/NZS1170.1
• Wind Load: Classifi cation N2, Non-Cyclonic to AS4055 where Vu = 40 m/s, Vs = 26 m/s
Windward wall Cpe = 0.7
Leeward Wall Cp,e = -0.3 to -0.5 as applicable based on shed geometry
Side Wall Cp,e = -0.5 to -0.65 as applicable based on shed geometry
Roof Cp,e = -0.5 to -1.3 depending on wind direction
6-12 Activity St, Acacia Ridge QLD 4110PO Box 119, Acacia Ridge QLD 4110
AU: 1800 029 701N Z: 0800 466 444
General
Absco Industries Assembly Instruction Manual
ABSCO REGENT SHEDMODEL: 30372RK3.00mW x 3.66mD x 2.10mH
Model: 30372RK 19/09/18 1.4 25
Absco Gable Roof Shed Notes
• 1.S All structural steelwork shall have a corrosion protection system applied consistent with AS/NZS 2312-2002.
• 2.S All structural steelwork detailed within this installation manual shall be minimum Grade
• 550 for roll formed sections (including roof and wall sheeting) and Grade 250 for angle sections.
• 3.S All roof, and wall sheeting shall be minimum base metal thickness of 0.3mm
• 4.S All snaptite channels and jambs shall be minimum base metal thickness of 0.42mm
• 5.S All top hats shall be minimum base metal thickness of 1.0mm
• 6.S All screw fasteners shall be Phil Pan Head Zinc Plated #8 x 3/4” (STP0820)
• 7.S All bolt fasteners for anchoring shall be M10 minimum grade 4.6/S
• 8.S Installation of screw fasteners shall generally be undertaken in accordance with the relevant provisions of AS1562.
Steelwork
• 1.F The supporting slab foundation for the garden shed shall be of a minimum size indicated on the installation manual. The top surface of the formed slab shall be level and free of any irregularities which would inhibit the installation of the shed.
• 2.F The structural engineering design for the supporting slab foundation shall be undertaken by a suitably qualifi ed structural engineer. The design shall consider all relevent provision of AS3600 and AS2870.
• 3.F Between adjacent footings or excavations, the contractor installing the slab foundation shall not exceed a rise of 1 in a run of 2 in line of slope.
• 4.F Unless approved in writing by the slab foundation engineer, the limits of excavations near existing footings shall be in accordance with that indicated below.
Supporting Slab and Foundations
The contactor shall undertake investigatory localised excavations near existing footings to ascertain their depth prior to excavating adjacent to them. It is noted that excavating to a depth below that indicated above shall not be undertaken without the written approval from the engineer.
Absco Industries Assembly Instruction Manual
ABSCO REGENT SHEDMODEL: 30372RK3.00mW x 3.66mD x 2.10mH
Model: 30372RK 19/09/18 1.4 26
Australia Product Warranty Against Defects
• Absco Sheds, including garden sheds, garden beds, aviaries, storage units, garages, awnings and carports are made using high quality Australian made steel.
• We are pleased to advise we warrant that the steel coating will not rust, crack, fl ake peel or blister for 30 years from date of purchase, when installed within Australia.
• This warranty does not apply to surface deterioration of panels caused by ‘Swarf” (Tiny particles of steel debris left from cutting, grinding or drilling operations) that has not been removed after building construction, or as a result of contact with damp soil, chemicals, fertilisers or other corrosive substances.
• This warranty covers any Absco product used for normal domestic use and installed in accordance with the installation instructions.
• The warranty does NOT cover Damage caused by storms, wind, rain snow or poor foundations.
• This warranty does NOT cover ABSCO products installed in severe coastal, industrial or other highly corrosive environments. The warranty does not cover fasteners (screws, nuts, bolts, rivets, hasps or sliding padbolts).
• The warranty is limited to replacement and delivery of components and does not include any labour or installation costs. The benefi ts given by the warranty are in addition to your other rights and remedies under a law in relation to the goods or services to which the warranty relates.
• The warranty applies to the exclusion of all other representations, guarantees or warranties express or implied, our goods come with guarantees that cannot be excluded under the Australian consumer law and is not transferable. You are entitled to a replacement or refund for a major failure and for compensation for any other foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of an acceptable quality and the failure does not amount to a major failure. For further information go to http://www.consumerlaw.gov.au
• Please retain a proof of purchase (sales docket or invoice) or register your warranty within 30 days of purchase here: www.absco.com.au/register_warranty.php
• In the unlikely event a warranty claim is made, it must be supported by photographic evidence and details of the defect, including component part numbers, together with proof of purchase documentation (or on-line registration of purchase) and forwarded to the address below. Upon receipt of the warranty claim, the Customer Service Manager will contact you within three business days to advise you of the assessment outcome of the claim, which may include your expenses incurred in making the claim.
THE CUSTOMER SERVICE MANAGER, ABSCO INDUSTRIES, PO BOX 119 ACACIA RIDGE QLD AUSTRALIA 4110
PHONE: 1800 029 701 FAX: 07 3344 1191 EMAIL: [email protected]
Issued 01 January 2018
Absco Industries Assembly Instruction Manual
ABSCO REGENT SHEDMODEL: 30372RK3.00mW x 3.66mD x 2.10mH
Model: 30372RK 19/09/18 1.4 27
Absco Sheds Storage Guidelines
• Absco Sheds are designed to be weatherproof for normal weather conditions. In the event of extreme weather conditions such as heavy rain, combined with high wind gusts, the ridge capping, sheeting joins, screw fi xings etc., may exhibit minor deformations which may allow some water entry. These areas should be checked regularly to ensure that maximum strength and protection is maintained.
• Other weather conditions such as extreme heat and extreme cold, moist or dry air can infl uence the effects of concrete fl oor moisture and/or condensation on the underside of the roof sheets.
• Absco Sheds and storage units are primarily used for storage of garden equipment such as lawnmowers, wheelbarrows, garden tools etc. Storage items that might be adversely affected by any of the above conditions may require additional protection such as being sealed or covered by plastic sheets and/or stacked above the concrete fl oor on timber slats.
• Waterproof sealants may be used to offer further protection where required around joins and screw fi xings, as can rubber door seals and other products which are available from most hardware outlets.
• Placement of waterproof sealants (silicone) between the base of the shed and concrete slab is not recommended, as this process can have a reverse effect, preventing excess water from escaping, resulting with water accumulating and being trapped inside the shed.
• Absco accepts no responsibility for water entry, fl oor moisture, condensation or the condition of the Contents inside your Absco steel building arising from any of the pre-mentioned weather conditions.
6-12 Activity St, Acacia Ridge QLD 4110PO Box 119, Acacia Ridge QLD 4110
AU: 1800 029 701N Z: 0800 466 444