asme b16.23 adoption notice asme 816.23, 'cast copper
TRANSCRIPT
ASME B16.23
ADOPTION NOTICE
ASME 816.23, 'Cast Copper Alloy Solder Joint Drainage Fittings - DWV,' wa8 adopted on 20 January 1984 for use by the Department of Defense (DoD). Proposed changes by DoD activities must be submitted to the DoD Adopting Activity: Defense Construction Supply Center, P. O. Box 3990, ATTN: DCSC-VSS, Columbus, OH 43216-5000. DoD activities may obtain copies of thí8 standard from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094. The private sector and other Qovernment agencies may purchase copies from the American Society of Mechanical Engineere, 345 East 47th Street, New York, NY 10017.
Custodian: Air Force - QG
Review Activity: Air Force - 82
Adopting Activity: DLA - CS (Project 4730-0318)
FSC 4730
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
ASME 8116.23 92 m 0759b70 05395211 770 m
ERRATA to
ASME B16.23-1992
The Errata correction listed below applies to ASME B16.23-1992, Cast Copper Alloy Solder Joint Drainage Fittings - DWV.
Page Location Change
2 9.1 Inspection Tolerance Table added
JANUARY 1994 THE AMERICAN SOCIEN OF MECHANICAL ENGINEERS
345 East 47th Street, New York, NY 10017 JO1 34E
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
ASME BLb.23 92 m O759670 0539522 607 m
ASME 816.23-1992
CAST COPPER ALLOY SOLDER JOINT DRAINAGE FITTINGS - D W V
1 SCOPE
1.1 Coverage
This Standard for cast copper alloy soider joint drainage fittings designed for use with copper drain- age tube covers:
(a) description (h) pitch (slope) (c) abbreviations for end connections (d) sizes, and methods for designing openings for
reducing fittings (e) marking cf) material (g) dimensions and tolerances
1.2 Units of Measurement
US. Customary units are the standard. For con- version to metric SI units, 1 in. equals 25.4 mm (not applicable to nominal tube or pipe size).
2 DESCRIPTION
(a) These fittings are designed for drainage and vent systems using the solder joint method of con- nection. The fitting cups (C) are provided with stops so that the ends of the tube, when assembled, meet the stops, thereby forming essentially smooth pas- sageways.
(b) The sketches and designs of fittings are illus- trative only. The dimensions specified herein shall govern in all cases.
3 PITCH (SLOPE)
all nominal 90 deg. fittings shall be pitched to re- sult in a slope of 0.25 in./ft (2.1%) of length of hor- izontal tube with reference to a horizontal plane.
4 ABBREVIATIONS
The following symbols are used to designate the type of fitting end:
C
FTG
F
M
SJ NPSM
5 SIZE
solder joint fitting end made to receive copper tube diameter (female) solder joint fitting end made to copper tube diameter (male) internal ANSI Standard taper pipe thread (female) NPT external ANSI Standard taper pipe thread (male) NPT end of fitting made to receive od tube size ANSI Standard straight mechanical pipe thread
(u) The size of the fittings scheduled in the fol- lowing tables corresponds to the drainage tube size shown in ASTM B306. The size of the threaded ends (except slip joints) corresponds to the nominal pipe size.
(b) Fittings are designated by the size of the open- ings in the sequence illustrated in Fig. 1.
6 MARKING
(u) Each fitting shall be marked permanently and legibly with the manufacturer’s name or trade mark, and with DWV (to indicate Drain Waste Vent).
(b) Vent fittings shall be permanently marked “VENT ONLY” (see Tables 42 and 43) and show the manufacturer’s name or trademark in accordance with MSS SP-25.
7 MATERIAL
Castings shall be copper alloy produced to meet: (u ) the requirements of ASTM B62 Alloy C83600;
or (b) the chemical and tensile requirements of
ASTM B584 Alloy 83800 or 84400; and in all other respects comply with the require- ments of of ASTM B62.
1
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
ASME B L b - 2 3 72
ASME 616.23-1992
0757670 0539523 543 m
CAST COPPER ALLOY SOLDER JOINT DRAINAGE FITTINGS - DWV
1 x 2 ~ 3 DWV Long Turn T-Y
1 x 2 ~ 3 DWV Tee
l x 2 x 3 x 4 Double Long Turn T-Y
l X 2 X 3 X 4 Tee With Side Inlet
1 x 2 deg. D W 90 deg. Elbow
FIG. 1 SIZE SEQUENCE OF FllTlNGS
Laying length u
Center m to end
c x c C x F
FIG. 2 TYPICAL LAYING LENGTHS OF D W 90 DEG. ELBOWS
8 METAL THICKNESS
Dimensional variations may occur in the casting process. Pattern equipment shall be designed to pro- duce the metal thickness given for fittings in Table 1. Any final fitting metal wall thickness less than 90% of the thickness given in the table is unacceptable.
2
9 INSPECTION TOLERANCE
9.1 Linear Dimensions
An inspection tolerance, as shown in the following Inspection Tolerance Table, shall be allowed on cen- ter-to-shoulder, center-to-threaded end, and shoul- der-to-threaded end dimensions on all fittings having female solder (cup) ends; and on center-to-solder end, solder end-to-shoulder, and solder end-to- threaded dimensions on all fittings having male sol- der (fitting) ends. The largest opening in the fitting governs the tolerance to be applied to all openings.
The inspection tolerance for laying length dimen- sions A, B, and C (Table 3) shall be double those shown above, except the minus tolerance applied to couplings, dimension A, shall not result in a dimen- sion less than 0.09 in.
Inspection Tolerance Table
i%, I % , and 2 1 (3:;; 4 and 5 0.12 i!! 4.0 6 and 8 0.16
9.2 Ovality
Maximum ovality shall not exceed 1% of the max- imum diameters shown in Table 1. The average of the maximum and minimum diameters must be within the dimensions shown in the table.
9.3 Alignment
The maximum allowable variations in the angular alignment of all openings shall be 0.06 in. in 1 ft (0.5%) other than in the direction of pitch.
9.4 Gaging of Solder Joint Ends
(a) Standard Gaging Method of Solder Joint Ends. The standard method of gaging the diameter toler- ances for male and female ends shall be by the use of plain plug and ring gages designed to hold the product within the limits established in Table 1.
(b) Optional Gaging Method of Solder Joint Ends. For gaging the diameter tolerance of male and fe- male ends, the manufacturer may use direct reading instruments instead of ring and plug gages as speci- fied in para. 9.4(a). When gaging the diameters of
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
. AN AMERICAN NATIONAL STANDARD
Cast Copper Alloy Solder Joint Drainage
Fittings - DWV
ASME B16.23-1992 (REVISION OF ANSI B16.23-1984)
@ The American Society of Mechanical Engineers
i 345 East 47th Street, New York, N.Y. 10017
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
Date of Issuance: June 30, 1992
The 1992 Edition of this Standard is being issued with an automatic addenda subscription service. The use of an addenda allows revisions made in re- sponse to public review comments or committee actions to be published as necessary; revisions published in addenda will become effective 6 months after the Date of Issuance of the addenda. The next edition of this Standard is scheduled for publication in 1995.
ASME will issue written replies to inquiries concerning interpretation of tech- nical aspects of this Standard. The interpretations will be included with the above addenda service. The interpretations are not part of the Standard
ASME is the registered trademark of The American Society of Mechanical Engineers.
This code or standard was developed under procedures accredited as meeting the criteria for American National Standards. The Consensus Committee that approved the code or standard was balanced to assure that individuals from competent and concerned interests have had an opportunity to participate. The proposed code or standard was made available for public review and comment which provides an opportunity for additional public input from industry, academia, regulatory agencies, and the public-at-large.
ASME does not "approve," "rate," or "endorse" any item, construction, proprietary device, or activity.
ASME does not take any position with respect to the validity of any patent rights asserted in connection with any items mentioned in this document, and does not undertake to insure anyone utilizing a standard against liability for infringement of any applicable Letters Patent, nor assume any such liability. Users of a code or standard are expressly advised that the determination of the validity of any such patent rights, and the risk of the infringement of such rights, is entirely their own responsibility.
Participation by federal agency representative(s) or person(s) affiliated with industry is not to be interpreted as government or industry endorsement of this code or standard.
ASME accepts responsibilityfor only those interpretations issued in accordance with governing ASME procedures and policies which preclude the issuance of interpretations by individual vol- unteers.
No part of this document may be reproduced in any form, in an electronic retrieval system or otherwise,
without the prior written permission of the publisher.
Copyright O 1992 by THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS
All Rights Reserved Printed in U.S.A.
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
ASME 816.23 92 m 0759670 0524120 756 m
O
m
m
O
O
FOREWORD
(This Foreword is not part of ASME 616.23-1992.)
Standardization work on solder joint fittings began in 1936 in Subcommittee 11 of Sectional Committee A40, Minimum Requirements for Plumbing and Standardization of Plumbing Equipment, organized within the American Standards Association (ASA). It resulted in the publication, in January 1941 of ASA A40.3-1941. That standard covered only supply (pressure) fittings.
In 1949, responsibility for solder joint fittings was transferred to newly formed Sub- committee 9 of Sectional committee B16 on Standardization of Pipe Flanges and Fittings. The next revision of A40.3 appeared as ASA €316.18-1950, Cast-Brass Solder-Joint Fit- tings. During its development, however, need for separate standards for wrought copper and wrought bronze supply fittings and for solder-joint drainage fittings was recognized.
Work on the wrought fitting standard was undertaken by a joint committee of the Copper and Brass Research Association and the Manufacturers’ Standardization Society of the Valve and Fittings Industry (MSS). That work, properly reviewed and approved, was published as ASA B16.22-1951.
Concurrently, in June 1949, at the request of Subcommittee 9, a task group organized by MSS began work on a standard for cast brass solder joint drainage fittings. Repre- sentitives of all U.S. and Canadian manufacturers were invited to participate. The Report of the Coordinating Committee for a National Plumbing Code was taken into account; special research on wall thickness and depth of solder joint was conducted; coordination with other standards was sought, to avoid inconsistency. After working through nine drafts to reach consensus, the group submitted an April 1952 draft to Subcommittee 9. After committee, sponsor, and ASA approval, the standard was approved as ASA B16.23-1953, Cast Brass Solder Joint Draniage Fittings, on January 30, 1953.
Work soon began on a revision, to include additional sizes, reducing sizes, and addi- tional types of fittings. A March 1955 draft was approved by B16, sponsors, and ASA, and published as ASA B16.23-1955. Starting in 1958, responding to requests for further revision and expansion, the MSS task group developed a 1959 draft which was approved by Subcommittee 9, the B16 Committee, sponsors, and ASA, and was published as ASA
In 1967 and 1968 a complete revision was undertaken, including engineering studies to verify that a user request for shorter soldering cups was justified. The resulting draft, after approval by Subcommittee 9, USA Standards Committee B16, sponsors, and the (then called) USA Standards Institute, was published as USAS B16.23-1969. An addenda, dated 1973, lengthened the cups on the three smallest sizes, to overcome assembly prob- lems.
The subcommittee, now Subcommittee I, began a new revision in 1974, resulting in the inclusion of the 1973 addenda, addition of metric equivalents, and change of “bronze” to “copper alloy.” The draft finally approved by the (again renamed) American National Standards Institute (ANSI) was published as ANSI B16.23-1976.
B16.23-1960.
111 ...
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
In 1982, a new edition, updating dimensional tables and metric equivalents, was de- veloped. Following approval at all levels, the revision was published as ANSI B16.23- 1984.
Also in 1982, American National Standards Committee B16 became the ASME B16 Standards Committee, operating with the same scope, under ASME procedures ac- credited by ANSI. Subsequently, Subcommittee I merged with Subcommittee J, which had a related scope.
This 1992 edition of B16.23 omits metric units, establishing U.S. customary units as the standard. Clarifications and updating changes were made in order to improve the text. Following approval by the standards committee and ASME, approval as an Amer- ican National Standard was given on February 28, 1992, with the designation ASME
Requests for interpretations and suggestions for revision should be sent to the Sec- retary, B16 Committee, The American Society of Mechanical Engineers, United Engi- neering Center, 345 East 47th Street, New York, NY 10017.
B16.23-1992.
iv
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
ASME BLb.23 92 m 0759b70 0524322 529 m
C O M M I ~ E E ON STANDARDIZATION'OF VALVES, FLANGES, FITTINGS, AND GASKETS
(The following is a roster of the Committee at the time of approval of this Standard.)
OFFICERS
W. N. McLean, Chairman R. A. Schmidt, Vice Chairman
J. Yarmush, Secretary
COMMITTEE PERSONNEL
W. L. Ballis, Columbia Gas Distribution Co., Columbus, Ohio J. E. Batey, Union Carbide Corp., South Charlston, West Virginia K. M. Bell, Underwriters Laboratories, Inc., Northbrook, Illinois M. L. Blair, U.S. Coast Guard, Washington, D.C. R. R. Brodin, Fischer Controls International, Inc., Marshalltown, Iowa W. G. Canham, Jr., Brentwood, Missouri A. Cohen, Copper Development Association, Greenwich, Connecticut W. C. Farrell, JI., Stockham Valves, Inc., Birmingham, Alabama C. E. Floren, Mueller Co., Decatur, Illinois D. R. Frikken, Monsanto Co., St. Louis, Missouri M. W. Garland, Frick Co., Waynesboro, Pennsylvania J. C. Inch, Mueller Brass Co., Hartsville, Tennessee J. S. John, J Square Engineering Co., Houston, Texas G. A. Jolly, Henry Vogt Machine Co., Louisville, Kentucky W. G. Knecht, Anchor/Darling Valve Co., Williamsport, Pennsylvania R. Koester. William Powell Co., Cincinnati, Ohio J. H. Longacre, Nibco, Inc., Elkhart, Indiana J. H. McCauley, Jr., McCauley Mechanical, Chicago, Illinois W. N. Mclean, Newco Valves, Palos Park, Illinois A. F. Rhodes, Arnco Technology Trust, Houston, Texas R. A. Schmidt, Ladish Co., Russellville, Arkansas W. M. Stephan, Flexitallic Inc., Pennsauken, New Jersey T. F. Stroud, Ductile Iron Pipe Research Association, Birmingham, Alabama R. E. White, Repairs, Inc., South Bend, Indiana D. A. Williams, Southern Company Services, Birmingham, Alabama D. Wilson, Mobile Pipeline Co., Dallas, Texas
SUBCOMMITTEE J - COPPER AND COPPER ALLOY FLANGES, FLANGED FITTINGS, AND SOLDER JOINT FITTINGS
J. H. Longacre, Chairman, Nibco, Inc., Elkhart, Indiana A. Nickles, Secretary, ASME, New York, New York D. Blankinship, Lee Brass Co., Anniston, Alabama A. Cohen, Copper Development Association, Greenwich, Connecticut D. R. Frikken, Monsanto Co., St. Louis, Missouri R. C. Haenke, Mueller Brass Co., Port Huron, Michigan M. E. Holmgren, Elkhart Products Corp., Elkhart, Indiana
V
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
O
O
O
' O
O
CONTENTS
Foreword ............................................................................... Standards Committee Roster .........................................................
1 2 3 4 5 6 7 8 9
10 11
Scope ........................................................................... Description ..................................................................... Pitch (Slope) ................................................................... Abbreviations .................................................................. Size ............................................................................. Material ........................................................................ Metal Thickness ................................................................ Inspection Tolerance .......................................................... Threaded Ends ................................................................. Configuration of Threaded Ends ..............................................
Marking .................................................................... .,. ...
Figures 1 Size Sequence of Fittings ...................................................... 2 Typical Laying Lengths of DWV 90 deg . Elbows .............................
Tables 1 2 3
4 5 6 7
8
9 10 11
12 13
14 15 16 17 18
Dimensions of Solder Joint Ends . DWV ................................... Dimensions of Threaded Ends ................................................ Dimensions for DWV Couplings. Reducers. Extended
Bushings. and Flush Bushings .............................................. Dimensions of DWV Adapters ................................................ Dimensions of DWV Short Adapters ......................................... Dimensions of DWV Trap Adapters .......................................... Dimensions of C to Soil Pipe Adapter for Joining to Extra
Heavy Soil Pipe .............................................................. Dimensions of C to Soil Pipe Adapter - Plain End for
Joining to Extra Heavy Soil Pipe ........................................... Dimensions of C X No-Hub Soil Pipe Adapter .............................. Dimensions of C X Hub Soil Pipe Adapter .................................. Dimensions of DWV 45 deg . Y With Cleanout-Soil Pipe
(Spigot) x C x Cleanout .................................................. Dimensions of DWV Elbows and Double Elbows - C x C ................ Dimensions of Reducing DWV Single & Double Elbows -
c x c ....................................................................... Dimensions of DWV Elbows .................................................. Dimensions of DWV Reducing Elbows ....................................... Dimensions of DWV Elbows .................................................. Dimensions of DWV Tees and Double Tees ................................. Dimensions of DWV Tees and Double Tees .................................
vii
... 111
V
1 1 1 1 1 1 1 2 2 3 3
4 4
4 5
6 7 8 8
9
10 11 12
12 13
14 15 16 16 17 18
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
19 20
21
22
23
24
25 26 27 28 29 30
31 32 33 34 35 36 37 38 39
40
41 42 43 44 45 46 47 48 49 50 51 52 53 54 55
ASME Blb.23 72 W 0757670 0524324 3Tl
O Dimensions of DWV Trap Tees ............................................... Dimensions of DWV Double and Quadruple Branch
Dimensions of Short Design DWV Tees With Side Inlet(s)
Dimensions of Short Design DWV Tees With Side Inlet(s)
Dimensions of Long Design DWV Tees With Side Inlet(s)
Dimensions of Long Design DWV Tees With Side Inlet(s)
.................................................................... Fittings
(90 deg . to Main Inlet). Single and Double ................................
(45 deg . to Main Inlet). Single and Double ................................
(90 deg . to Main Inlet). Single and Double ................................
(45 deg . to Main Inlet). Single and Double ................................ Dimensions of Single and Double DWV 45 deg . Ys ......................... Dimensions of DWV 45 deg . Ys .............................................. Dimensions for DWV Horizontal Twin Branch Tees ........................ Dimensions for DWV Fitting Tees. Single and Double ...................... Dimensions for DWV Utility Tees ............................................ Dimensions of DWV Fitting Tees With Side Inlet Maximum
Below Center Line .......................................................... Dimensions of DWV Long Turn T-Ys. Single and Double .................. Dimensions of DWV Double Short T-Y ..................................... Dimensions of DWV Double Short T-Y ..................................... Dimensions of DWV Elbow With Inlets ...................................... Dimensions of DWV Double Branch Sink Fittings .......................... Dimensions of DWV Closet Offset Fittings .................................. Dimensions of DWV 90 deg . Closet Elbow ................................... Dimensions of Floor Flange Vent Support ...................................
and 45 deg.) to Main Inlet(s) ...............................................
Inlet(s) (90 deg . and 45 deg.) to Main Inlet(s) ............................ Dimensions of DWV Closet Flanges .......................................... Dimensions of Vent Tees and Vent Double Tees ............................ Dimensions of Vent Elbows ................................................... Dimensions of DWV Stack Upturns. Single and Double ....................
Dimensions of DWV Closet Ells With Side Inlet(s) (90 deg .
Dimensions of DWV Closet Ells With or Without Side
Dimensions of Slip Joint Pieces ............................................... Dimensions of Trap Coupling ................................................. Dimensions of Trap Extended Bushings ...................................... Dimensions of Slip Joint Ends ................................................ Dimensions of DWV Cap ..................................................... Dimensions of DWV Plugs .................................................... Dimensions of DWV Drum Traps ............................................ Dimensions of DWV Swivel Drum Trap ...................................... Dimensions of DWV Traps .................................................... Dimensions of DWV Test Tees With Plug ................................... Dimensions of DWV Plugs ....................................................
19
19
20
20
21
21 22 23 23 24 25
25 26 27 27 28 29 29 30 30
31
32 33 34 35 35 36 36 37 37 38 38 39 40 41 42 42
Annex A References ..................................................................... 43
viii
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
ASME 816.23-1992
CAST COPPER ALLOY SOLDER JOINT DRAINAGE FITTINGS - DWV
1 SCOPE
1.1 Coverage
This Standard for cast copper alloy solder joint drainage fittings designed for use with copper drain- age tube covers:
(a) description (b) pitch (slope) (c) abbreviations for end connections (d) sizes, and methods for designing openings for
reducing fittings (e) marking cf3 material (g) dimensions and tolerances
1.2 Units of Measurement
U.S. Customary units are the standard. For con- @ version to metric SI units, 1 in. equals 25.4 mm (not applicable to nominal tube or pipe size).
2 DESCRIPTION
(u) These fittings are designed for drainage and vent systems using the solder joint method of con- nection. The fitting cups (C) are provided with stops so that the ends of the tube, when assembled, meet the stops, thereby forming essentially S 00th pas- sageways.
(b) The sketches and designs of fittings are illus- trative only. The dimensions specified herein shall
3
govern in all cases.
3 PITCH (SLOPE)
all nominal 90 deg. fittings shall be pitched to re- sult in a slope of 0.25 in./ft (2.1%) of length of hor- izontal tube with reference to a horizontal plane.
4 ABBREVIATIONS
type of fitting end: The following symbols are used to designate the
C
FTG
F
M
SJ NPSM
5 SIZE
solder joint fitting end made to receive copper tube diameter (female) solder joint fitting end made to copper tube diameter (male) internal ANSI Standard taper pipe thread (female) NPT external ANSI Standard taper pipe thread (male) NPT end of fitting made to receive od tube size ANSI Standard straight mechanical pipe thread
(u) The size of the fittings scheduled in the fol- lowing tables corresponds to the drainage tube size shown in ASTM B306. The size of the threaded ends (except slip joints) corresponds to the nominal pipe size.
(b) Fittings are designated by the size of the open- ings in the sequence illustrated in Fig. 1.
6 MARKING
(u) Each fitting shall be marked permanently and legibly with the manufacturer’s name or trade mark, and with DWV (to indicate Drain Waste Vent).
(b) Vent fittings shall be permanently marked “VENT ONLY” (see Tables 42 and 43) and show the manufacturer’s name or trademark in accordance with MSS SP-25.
7 MATERIAL
Castings shall be copper alloy produced to meet: (a) the requirements of ASTM B62 Alloy C83600;
or (b) the chemical and tensile requirements of
ASTM B584 Alloy 83800 or 84400; and in all other respects comply with the require- ments of of ASTM B62.
1
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
ASME 616.23-1992
1 x 2 ~ 3 DWV Long Turn T-Y
1 ~ 2 x 3 DWV Tee
CAST COPPER ALLOY SOLDER JOINT DRAINAGE FITTINGS - DWV
8 METAL THICKNESS
Dimensional variations may occur in the casting process. Pattern equipment shall be designed to pro- duce the metal thickness given for fittings in Table 1. Any final fitting metal wall thickness less than 90% of the thickness given in the table is unacceptable.
' 1 x Z x 3 x 4 Double Long Turn T-Y
1 X Z X 3 X 4 Tee With Side Inlet
DWV
1 x 2 deg. DWV 90 deg. Elbow
FIG, 1 SIZE SEQUENCE OF FITTINGS
Laying length *- ~ 4 , Center
H to end 7
P"
f
Laylng Laying length length r - tf
W c x c C x F
FIG. 2 TYPICAL LAYING LENGTHS OF DWV 90 DEG. ELBOWS
2
9 INSPECTION TOLERANCE
9.1 Linear Dimensions
An inspection tolerance, as shown in the following Inspection Tolerance Table, shall be allowed on cen- ter-to-shoulder, center-to-threaded end, and s h o d der-to-threaded end dimensions on all fittings having female solder (cup) ends; and on center-to-solder end, solder end-to-shoulder, and solder end-to- threaded dimensions on all fittings having male sol- der (fitting) ends. The largest opening in the fitting governs the tolerance to be applied to all openings.
The inspection tolerance for laying length dimen- sions A, B, and C (Table 3) shall be double those shown above, except the minus tolerance applied to couplings, dimension A, shall not result in a dimen- sion less than 0.09 in.
9.2 Ovality
Maximum ovality shall not exceed 1% of the max- imum diameters shown in Table 1. The average of the maximum and minimum diameters must be within the dimensions shown in the table.
9.3 Alignment .c The maxlmum allowable variations in the angular
alignment of all openings shall be 0.06 in. in 1 ft (0.5%) other than in the direction of pitch.
9.4 Gaging of Solder Joint Ends
(a) Standard Gaging Method of Solder Joint Ends. The standard method of gaging the diameter toler- ances for male and female ends shall be by the use of plain plug and ring gages designed to hold the product within the limits established in Table 1.
(b) Optional Gaging Method of Solder Joint Ends. For gaging the diameter tolerance of male and fe- male ends, the manufacturer may use direct reading instruments instead of ring and plug gages as speci- fied in para. 9.4(a). When gaging the diameters of
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
ASME 816.23 72 m 0757670 0524327 O00 m
CAST COPPER ALLOY SOLDER JOINT DRAINAGE FITTINGS - DWV
ments, refer to para. 9.2. male and female ends, using direct reading instru-
10 THREADED ENDS
10.1 General
Fitting threads shall be right hand, conforming to ANWASME B1.20.1. They shall be taper threads (NPT) except for slip joint ends which shall have straight pipe threads (NPSM).
10.2 Thread Dimensions
All internal threads shall be countersunk a dis- tance not less than one-half the pitch of the thread at an angle of approximately 45 deg. with the axis of the thread, and all external threads shall be cham- fered at an angle of 30 deg. to 45 deg. from the axis, for the purpose of easier entrance in making a joint and protection of the thread. countersinking and chamfering shall be concentric with the threads. The length of threads specified in all tables shall be mea- sured to include the countersink or chamfer.
10.3 Threading Tolerances
Tapered pipe threads (NPT) shall be checked by use of working plug or ring gages, either standard or
ASME 816.23-1992
limit types. Gages shall be threaded on/in hand tight. The reference point for gaging internal product threads depends upon the chamfer diameter. When the internal chamfer diameter exceeds the major di- ameter of the internal thread, the reference point is the last thread scratch on the chamfer cone. Other- wise, when the internal chamfer diameter does not exceed the major diameter of the internal thread, the reference point is the end of the fitting. On the ex- ternal thread it shall be flush with the end of the fitting.
Tolerance for an internal threaded end having an internal shoulder shall be from one turn large to one turn small. Tolerance for an internal threaded end without shoulder and for an external threaded end shall be from one-half turn small to one and one-half turn large.
Strait pipe threads (NPSM) shall be checked by use of the standard GO and NOT GO plug and ring gages.
11 CONFIGURATION OF THREADED ENDS
At the manufacturer’s option, female ends of fit- tings may be furnished with a polygon or bead with or without ribs, and male ends of fittings may be furnished with a polygon, ribs, or flats.
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
ASNE B36.23 92 0759670 0524328 T 4 7 D
CAST COPPER ALLOY SOLDER JOINT DRAINAGE FITTINGS - DWV ASME B16.23-1992
F ,
k K - Male End
FTG
I
Female End C
TABLE 1 DIMENSIONS OF SOLDER JOINT ENDS - DWV'
Inside Diameter
o Min.
Male End
Outside Diameter Female End
Inside Diameter I Depth Metal T Body
T r Length
K5 Min.
I Min. Size2 Max. Min.
lx 1 v2 2 3
1.372 1.621 2.121 3.121
4.121 5.121 6.121 8.1 19
1.377 1.627 2.1 27 3.1 27
4.1 27 5.1 27 6.1 27 8.1 27
0.56 0.62 0.69 0.81
1 .O6 1.31 1.62 2.12
1.378 1.628 2.1 28 3.128
4.128 5.128 6.128 8.128
0.10 0.1 o 0.1 o 0.1 2
0.1 2 0.1 9 0.19 0.22
1.382
0.75 3.1 33 0.62 2.1 33 0.56 1.633 0.50
4.133 1 .o0 5.133 1.25 6.1 33 1.50 8.133 2.00
0.07
2.98 0.10 2.01 0.09 1.53 0.08 1.29
0.12 3.93 0.19 4.91 0.19 5.88 0.22 7.78
4 5 6 8
GENERAL NO I 3: Dimensions are in inches.
NOTES: (1) The sketches and designs of fittings are illustrative only. The dimensions herein shall govern in all cases. (2) For size designation of fitting, see Section 5. (3) For metal thickness tolerance, see Section 8. (4) For ovality see section 9.2. (5) K dimensions of 0.44, 0.50, and 0.56, and G dimensions of 0.38, 0.44, and 0.50, respectively, for lY4, lx, and 2 in. sizes are
sound and acceptable7rom an engineering standpoint. However, the cup depths specified in Table 1 are to provide greater facility in making installations.
4
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
ASME 816.23 92 m 0759b70 0524129 983 m
CAST COPPER ALLOY SOLDER JOINT DRAINAGE FITTINGS - DWV
Female Threaded End (F)
S - k ~ V A
Female Threaded End (F)
ASME 816.23-1992
(t-zz-i I Male Threaded End
(M)
- i y L Male Threaded End
(M)
TABLE 2 DIMENSIONS OF THREADED ENDS” - DWV
Female End
Diam. of Band or Across Flats of Band
Nominal Polygon Length Thread A B
Size‘ Min. Min.
1 Ya 1.91 0.31 1 ’/z 2.17 0.34 2 2.69 0.41 3 3.88 0.55
4 4.94 0.66 5 6.12 0.78 6 7.30 0.88 8 9.38 1.12
D:.
Min. Min.
Thread Recesss
1.90 1.66 2.17 1.91 2.68 2.38 3.88 3.50
4.94 4.50 6.1 2 5.56 7.30 6.62 9.37 8.62
GENERAL NOTE: Dimensions are in inches. I
Depth Length of Full Thread
Min. Min. Min.
0.71 0.72 0.76 1.20
1.30 1.41 1.51 1.71
1 .o0 1 .o0 1 .O3 1.46
1.53 1.66 1.68 1.75
0.42 0.42 0.44 0.77
0.84 0.94 0.96 1 .O6
End to
Should- er5 YY
f 0.06
0.70 0.72 0.75 1.20
1.30 1.41 1.50 1.70
Thread End
WallE S
Min.
0.1 20 0.130 O. 150 0.1 90
0.220 0.280 0.340 0.375
NOTES: (1) Thread size is American National Standard Pipe Threads, General Purpose (inch), ANWASME B1.20.1. (2) lY4, 1Y2, and 2 male threaded ends may have inside chamfer for slip nut connections. (3) For threads of threaded ends, see Section 10. (4) Dimensions taken from ANSI 816.12. (5) Dimensions computed using formula E, - h - 2T.
E, = thread pitch diameter from ANWASME 81.20.1 h = height of thread from ANSVASME 120.1 T = metal thickness from Table 1.
(6) For initial thickness tolerance, see Section 8. (7) For inside diameter of fitting, see Table 1.
Male End
Length
Max. I Min.
3.05
4.05 1.30
6.03 1.51 7.95 1.71
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
A S I E BLb.23 72 m 0757670 0524330 bT5 m
CAST COPPER ALLOY SOLDER JOINT DRAINAGE FllTlNGS - DWV
DWV Coupling DWV Reducer DWV Extended c x c c x c Bushing
FTG x C
E beD-?
El DWV Flush Bushing
FTG x C
TABLE 3 DIMENSIONS FOR DWV COUPLINGS, REDUCERS, EXTENDED BUSHINGS,
AND FLUSH BUSHINGS
Size
1 Y4 1 Y2 1 Y2 x 1y4
2 2 x 1Y2 2 x lY*
3 3 x 2 3 x 1Y* 3 x lY4
4 4 x 3 4 x 2 4 x lY2
5 5 x 4 5 x 3
6 6 x 5
3 8 x 6
:oupling
A
0.12 0.12 . . .
0.12 . . . . . .
0.19 . . . . . . . . .
0.19 . . . . . . . . . 0.25 . . . . . . 0.25 . . . 0.38 . . .
Xeducer
B
. . . * . . 0.25
* . . 0.38 0.44
. . . 0.75 0.94 0.94
. . . 0.34 0.50 1.50
. . . 0.56 0.88
. . . 0.53
. . . 1.38
xtendec aushing
C
. . .
. . . 0.75
. . . 0.91 0.94
. . . 1.38 1.31 1.31
. . . 1.62 1.75 . . .
. . . 1.56 1.88
. . . 2.94
* . . . . .
GENERAL NOTE: Dimensions are in inches.
6
Flush Bu:
D -
...
. . . 0.62
. . . 0.69 0.69
. . . 0.81 0.81 . . . . . . 1 .O6 . . . . . . . . . . . . . . .
. . .
. . . * . . . . . -
ng E
. . .
. . . 0.12
. . . 0.13 0.19
. . . 0.19 0.25 . . .
. . . 0.31 . . . . . . . . . . . . . . .
. . .
. . .
. . .
. . .
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
CAST COPPER ALLOY SOLDER JOINT DRAINAGE FITTINGS - DWV ASME 816.23-1992
C x F C x M FTG x F FTG x M
DWV Adapters
TABLE 4 DIMENSIONS OF DWV ADAPTERS
Size
1 Y* l’/* x 2 1 Y. x lY2 1 Yz
‘lY2 x lY* x 2
2 2 x 3 2 x lY2 2 x lY4
3 3 x 4 3 x 2
4 4 x 3
5 6 8
GENERAL NOTE:
C x F A
0.81 0.94 0.81 0.81 0.88 0.81
0.88 1.88 0.88 0.88
1.50 2.25 1.56
1.66 1.69
1.94 2.19 2.62
C x M A
0.94 1.31 1.12 0.94 1.25 1 .O6
0.94
1 .O6 1 .O6
1.56
1.44
1.62
. . .
. . .
. . .
1.75 2.00 3.38
FTG x F A
1.47 * . . . . . 1.53 . . . . . .
1.63 . . . . . . . . . 2.38 * . . . . .
2.81 . . . . . . 3.81 4.38
imensions are in inches.
T G X M A
1.94 . . . . . . 2.06 . . . . . .
2.38 . . . . . . . . .
3.00 . . . . . .
3.62 . . .
. . .
. . .
. . .
7
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
ASME 816.23-1992
ASME BLb.23 92 0759b70 0524132 478 m
t""1 1 "IB"
C x M
DWV Short Adapters
TABLE 5 DIMENSIONS OF DWV SHORT ADAPTERS
C x M Size A 0
1 Ya
1 Y4 x 1 Y2 1 .o0 0.44 1 Y2 1 .o0 0.50
1.19 0.62 lY* x 2 1.12 0.50 2 1 .o0 0.50
GENERAL NOTE: Dimensions are in inches.
CAST COPPER ALLOY SOLDER JOINT DRAINAGE FITTINGS - DWV
FTG x SJ C X S J
DWV Trap Adapters
TABLE 6 DIMENSIONS OF DWV TRAP ADAPTERS
FTG x SJ A A
C x SJ Size
1 Y4 1 Y2
0.62 1.19
0.69 . . . 2 x 1Y2 0.69 . . . 2 0.69 . . . 1 Y2 x 1 Ya 0.69 1.25
GENERAL NOTES: (a) Dimensions are in inches. (b) For dimensions of slip joint ends, see Table 48.
8
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
CAST COPPER ALLOY SOLDER JOINT DRAINAGE FITTINGS - DWV ASME B16.23-1992
W 0.12 4 i- W
0.22 min.
Straight Sizes Reducing Sizes
DWV Soil Pipe Adapter-C x Spigot
TABLE 7 DIMENSIONS OF C TO SOIL PIPE ADAPTER FOR JOINING TO EXTRA
HEAVY SOIL PIPE
Size Soil Pipe'
c x spigot
2 x 2 1-1'/2 x 2 lY4 x 2 3 x 3 2 x 3 lY* x 3
4 x 4 3 x 4 2 x 4 lY* x 4 5 x 5 6 x 6
Diameter of Bead h
Max. Min.
2.75 2.69 2.75 2.69 2.75 2.69 3.88 3.81 3.88 3.81 3.88 3.81
4.88 4.81 4.88 4.81 4.88 4.81 4.88 4.81
6.88 6.81 5.88 5.81
GENERAL NOTE: Dimensions are in inches.
NOTES:
Body Wall W
0.10 0.10 0.10 0.12 0.12 0.12
0.12 0.12 0.12 0.12 0.19 0.22
Body Outside
Diameter2 N = 0.09
2.38 2.38 2.38 3.50 3.50 3.50
4.50 4.50 4.50 4.50 5.50 6.50
Body LengthS H -C 0.06
2.50 3.25 3.25 2.75 3.50 3.50
3.00 3.75 3.75 3.75 3.00 3.00
Laying Length
J
2.50 2.31 3.31 2.75 3.56 3.56
3.00 3.81 3.88 3.88 3.00 3.00
(1) Dimensions given are for extra heavy weight soil pipe. Refer to ASTM A74. For service
, ers should be marked " S W or "SERVICE WEIGHT." (2) N is taken from outside diameter of XH soil pipe. (3) H body lengths are based on "telescoping lengths of XH soil pipe hubs."
weight, A and N may be reduced as shown in Table 2 of ASTM A74. Service weight adapt-
9
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
ASME 616.23-1992 CAST COPPER ALLOY SOLDER JOINT
DRAINAGE FllTlNGS - DWV
C x Soil Pipe For use with elastomer gasket
DWV Soil Pipe Adapters-Plain End
TABLE 8
TO EXTRA HEAVY SOIL PIPE DIMENSIONS OF C TO SOIL PIPE ADAPTER - PLAIN END FOR JOINING
Size Body Body Laying Length 1 I Wall 1 Length
Body
I H 0.06 I N f 0.09 I W I J
2 x 2 lY4 x 2 1Y2 x 2
3 x 3 2 x 3 3 x 4
2.50 2.50 2.50
2.75 2.75 3.00
2.38 2.38 2.38
3.50 3.50 4.50
0.10 0.10 0.1 o
0.12 0.12 0.12
2.50 2.56 2.56
2.75 2.81 3.06
GENERAL NOTE: Dimensions are in inches.
10
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
CAST COPPER ALLOY SOLDER JOINT DRAINAGE FllTlNGS - DWV ASME 616.23-1992
,112 x 1/16 x 1/16 lug.
Straight Sizes Reducing Sizes
DWV Soil Pipe Adapter -C x No-Hub For use with stainless steel clamp and elastomer gasket
TABLE 9 DIMENSIONS OF C X NO-HUB SOIL PIPE ADAPTER
Diameter Outside Laying I of Bead I ~~~~~~ 1 Length Size
C X No-Hub A 2 0.06 B 2 0.06 D
2 2.38 2.31 1.22 1% x 2 2.38 2.31 1.25 lye x 2 2.38 2.31 1.28 3 3.41 3.34 1.22
4.44 4.38 1.22 3 x 4 4.44 4.38
GENERAL NOTE: Dimensions are in inches.
Metal Thickness‘ T Body
E
o. 1 O0 0.100 0.100 0.120
0.1 20 0.120 0.120 0.120
Joint
R
0.090
0.072 0.1 03
0.090 0.078 0.120 0.1 03
0.078
Width Bead, Min.
F +0.13 - 0.00
0.25 0.25 0.25 0.25
0.25 0.25 0.31 0.31
11
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
ASME B L b - 2 3 92 0759670 0524336 013
CAST COPPER ALLOY SOLDER JOINT DRAINAGE FITTINGS - DWV
" I t w
ASME 816.23-1992
DWV Soil Pipe Adapter C x Hub
TABLE 10 DIMENSIONS OF C
x HUB SOIL PIPE ADAPTER' Size
0.19 0.12
GENERAL NOTE: Dimensions are in inches.
NOTE: (1) For hub end dimensions, see ASTM A74.
DWV 45 deg. Y With Clesnout
TABLE 11
PIPE (SPIGOT) x C x CLEANOUT DIMENSIONS OF DWV 45 DEG. Y WITH CLEANOUT-SOIL
A B
Size W KK J C Min. Min. Max.
4 X 3 X 3
GENERAL NOTE: Dimensions are in inches.
0.12 4.1 2 3.00 8.50 5.1 2 4.81 4.83
12
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
CAST COPPER ALLOY SOLDER JOINT DRAINAGE FllTlNGS - DWV ASME 616.23-1992
DWV 90 deg. Elbow DWV 60 deg. Elbow DWV 45 deg. Elbow C x C a n d C x C x C c x c C X C
DWV 22-112 deg. Elbow DWV 11-114 deg. Elbow c x c c x c
TABLE 12 DIMENSIONS OF DWV ELBOWS AND DOUBLE ELBOWS - C X C
Size
DWV 90 deg. elbow c x c
DWV 60 deg. elbow c x c
DWV 45 deg. elbow
O c x c
DWV 22Y2 deg. elbow c x c
DWV 111/, deg. elbow c x c
1 v4 1 v2 1.19 1.44
0.69 0.81
0.50 0.56
0.19 0.25
0.12 0.12
2
1.94
1.12
0.81
0.38
0.19
3
2.94
1.69
1.19
0.56
0.25
4
3.88
2.25
1.62
0.75
0.31
5 1 6 4.88 5.81
2.88 3.50
2.06 2.50
0.94 1.12
0.41 0.50
8
7.81
4.62
3.31
1.50
0.66
iches.
13
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
ASME 616.23-1992
ASME BLb.23 92 0757670 0524338 79b m
CAST COPPER ALLOY SOLDER JOINT DRAINAGE FllTlNGS - DWV
O
DWV 90 deg. Elbow, C x C DWV Double Elbow, C x C x C
TABLE 13 DIMENSIONS OF REDUCING DWV SINGLE & DOUBLE ELBOWS - C X C
~~ ~
Size C x C o r C x C x C I lY2 x lY4 2 x lY2 I 2 x lY4 I 4 x 3
DWV 90 deg. reducing 2.81 1.19 1.44 1.19 K elbow
c x c 3.00 1.56 1.69 1.31 KK
GENERAL NOTE: Dimensions are in inches.
14
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
ASME 816.23 92 D 0759670 0524339 822 m
CAST COPPER ALLOY SOLDER JOINT DRAINAGE FITTINGS - DWV
DWV 90 deg. Elbow FTG x C
i
DWV 60 deg. Elbow C x M
DWV 90 deg. Elbow DWV 90 deg. Elbow C x F FTG x F
ASME B16.23-1992
P-L y I
DWV 90 deg. Elbow C x M
DWV 45 deg. Elbow DWV 45 deg. Elbow DWV 45 deg. Elbow DWV 45 deg. Elbow FTG x C C x F C x M FTG x M
DWV 22-1/2 deg. Elbow DWV 11-114 deg. Elbow C x M C x M
TABLE 14 DIMENSIONS OF DWV ELBOWS
Size
DWV 90 deg. elbow FTG x C
DWV 90 deg. elbow C X F
DWV 90 deg. elbow FTG x F
DWV 90 deg. elbow C x M
DWV 45 deg. elbow FTG x C
K G
K L
G L
K L
K G
1 v. 1.19 1.75
1.19 1.88
1.75 1.88
1.19 , 1.88
0.50 1 .O6
GENERAL NOTES: (a) Dimensions are in inches. (bl See Table 15 for reducing sizes. (c) See Table 16 for Continuation of dimensions.
1.44 2.12
1.44 2.1 2
2.06 2.12
1.44 2.12
0.56 1.19
2
1.94 2.69
1.94 2.69
2.69 2.69
1.94 2.81
0.81 1.50
3
2.94 3.75
2.94 3.94
3.75 3.94
2.94 3.94
1.19 2.00
4
3.88 4.88
3.88 4.94
4.81 5.00
3.88 4.94
1.62 2.69
15
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
ASME 816.23-1992
ASME Blb.23 92 m 0759670 0524340 5 4 4 W
CAST COPPER ALLOY SOLDER JOINT DRAINAGE FllTlNGS - DWV
TABLE 15 DIMENSIONS OF DWV REDUCING ELBOWS'
D W 90 Deg. Elbow Elbow
DWV 90 Deg.
C x M C x F
Size 1 K L K
1 '/> x 1 1.88 1.31 2.00 1.31
GENERAL NOTE: Dimensions are in inches.
NOTE: (1) Refer to illustrations Table 14.
TABLE 16 DIMENSIONS OF DWV ELBOWS' Size
DWV 60 deg. elbow C x M
D W 45 deg. elbow C x F
DWV 45 deg. elbow C x M
DWV 45 deg. elbow FTG x M
DWV 22Y2 deg. elbow C x M
DWV 11 Y4 deg. elbow C x M
1 Y* K 0.66 L 1.28
K 0.30 L 1.28
K 0.50 L 1.19
L 1 .O6 G 1 .O3
K 0.19 L 0.81
K 0.12 L 0.75
1 Y2
0.81 1.50
0.36 1.38
0.56 1.31
1.25 1.19
0.25 0.94
0.12 0.81
2
1 .o9 1.84
0.75 1.66
0.75 1.33
1.33 1.30
0.34 1 .o9
0.19 0.94
NOTE: (1) Refer to illustrations Table 14.
16
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
ASME Blkb-23 92 m 0759670 0524343 480 D
CAST COPPER ALLOY SOLDER JOINT DRAINAGE FITTINGS - DWV
Size
1 1 Y 2
lY2 x lY2 x lY4 lY2 x lY4 x lY2 lY2 x lY4 x lY*
2 2 x 2 x 1Y2 2 x 2 x lY4 2 x I Y 2 x 2 2 x lY2 x lY2 2 x lY2 x 1y4
3 3 X 3 X 2 3 X 3 X l ' / , 3 x 3 x lYa 3 x 2 ~ 3 3 X 2 X 2
DWV Tees c x c x c
c x c x c x c
TABLE 17 DIMENSIONS OF DWV TEES AND DOUBLE TEES
J
1.19 1.44 1.31 1.44 1.31
1.94 1.69 1.56 1.94 1.69 1.69
2.94 2.44 2.19 2.06 2.94 2.44
K
1.19 1.44 1.19 1.44 1.19
1.94 1.44 1.19 1.94 1.44 1.44
2.94 1.94 1.44 1.19 2.94 1.94
~ ~~~ ~ L GENERAL NOTE: Dimensions are in inches.
KK
0.69 0.81 0.69 0.81 0.75
1 .o0 0.81 0.69 1 .o0 0.81 0.75
1.50 1 .o0 0.81 0.69 1.28 0.97
Size
3 x 2 x 1Y2 3 x lY2 x 3 3 x 1 Y2 x 1 7/2
4 4 X 4 X 3 4 X 4 X 2 4 x 4 x lY2 4 x 4 x lY4 4 x 2 ~ 4
5 5 X 5 X 4
6 6 x 6 ~ 4 6 X 4 X 4
8 8 X 8 X 6 8 X 6 X 6
J
2.81 2.94 2.19
3.88 3.44 2.88 2.62 2.50 3.88
4.88 4.38
5.81 4.88 4.81
7.81 6.69 6.75
ASME B16.23-1992
K
1.44 2.94 1.44
3.88 2.94 1.94 1.44 1.19 3.88
4.88 3.88
5.81 3.88 3.88
7.81 5.81 5.81
KK
0.84 1.25 0.69
2.06 1.50 1 .o0 0.81 0.69 1.25
2.31 1.94
2.75 1.94 1.50
3.44 2.69 2.31
17
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
ASME 816.23-1992
ASME BLb-23 92 m 0759b70 0524342 317 m
CAST COPPER ALLOY SOLDER JOINT DRAINAGE FITTINGS - DWV
O
C ~ F X F
T- N
t- i‘
C x F x C C x F x C x C
DWV Tees and Double Tees
C x C x F C x C x F x F
TABLE 18 DIMENSIONS OF DWV TEES AND DOUBLE TEES
Size
1 1 ’/2 lYz x lY2 x 1% lYz x 1% x 1%
2 2 x 2 x IV!* 2 x 2 x lY4 2 x lY2 x 1Y2 2 x lY2 x 2
3 3 X 3 X 2 3 X 3 X l ’ / , 3 X 3 X l X
4 4 X 4 X 3 4 X 4 X 2 4 x 4 x lY2 4 x 4 x lYa
K
1.19 1.44 1.19 1.44
1.94 1.44 1.19 1.44 1.94
2.94 1.94 1.44 1.19
3.88 2.94 1.94 1.44 1.19
I L
1.38 1.56 1.56 1.56
1.75 1.75 1.75 1.56 * . .
2.69 . . . . . . . . .
3.31 . . . . . . . . . . . .
M
1.88 2.19 2.19 2.19
2.69 2.38 2.25 2.38 . . *
3.94 . . . . . . . . .
4.94 . . . . . . . . . . . .
1.50 2.1 2 2.00
. . I 2.12 1.75
. . . 1.75 2.38 . . . 2.25 . . . 2.38 . . . 2.69
2.50 3.94 . . . 3.19 . . . 2.88 . . . 2.75
3.31 4.94 . . . 4.44 . . . 3.62 . . . 3.31 . . . 3.19
KK
0.69 0.81 0.69 0.81
1 .o0 0.81 0.69 0.88 . . . 1.50 1 .o0 0.81 0.69
1.94 1.50 1 .o0 0.81 0.69
GENERAL NOTE: Dimensions are in inches.
18
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
ASME 816.23 92 0759670 0524143 253 m
CAST COPPER ALLOY SOLDER JOINT DRAINAGE FITTINGS - DWV
DWV Trap Tees C x F x S J
DWV Trap Tees C x C x S J
TABLE 19 DIMENSIONS OF DWV TRAP TEES’
ASME 616.23-1992
Size LL KK M L K
1%
2.62 1.12 2.78 1.75 1.94 2 2.1 2 0.75 2.19 1.56 1.19 l‘/z x I’/z x lY4 2.25 0.81 2.31 1.56 1.44 1 Y2 1.94 0.75 2.00 1.38 1.19
GENERAL NOTE: Dimensions are in inches.
NOTE: (1) For dimensions of slip joint ends, see Table 48.
C
c x c x c x c c x c x c x c x c x c DWV Branch Fittings
DIMEN TABLE 20
QUADRUPLE BRANCH FITTINGS ISIONS OF DWV DOUBLE AND
3 x 3 with 1Y2 inlets
4.44 1.44 2.50 4 x 4 with 1% inlets 4.44 1.44 2.62 4 x 4 with 1Y’ inlets 4.94 1.56 2.06 3 x 3 with 1% inlets 4.94 1.56 2.19
GENERAL NOTE: Dimensions are in inches.
19
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
ASME B1b.23 92 m 0757670 0524144 L 9 T m
ASME 816.23-1992
DIMEN
CAST COPPER ALLOY SOLDER JOINT DRAINAGE FITTINGS - DWV
Not greater than KK
C x C x C With One or Two C Side Inlet(r) C x C x C x C With One or Two C Side Inletls)
DWV Tees-Short Design
TABLE 21 DIMENSIONS OF SHORT DESIGN DWV TEES
WITH SIDE INLET(S)' (90 DEG. TO MAIN INLET), SINGLE AND DOUBLE
Size K KK X
3 x 3 x 3 with 2 in. inlet(s) 2.94 1.50 2.25 3 x 3 x 3 with lYz in. inlet(s) 2.94 1.50 2.12
GENERAL NOTE: Dimensions are in inches.
NOTE: (1) To determine whether inlets are right hand or left hand,
place the fitting with large side inlet facing toward you. The side on which the other inlet appears determines its designation.
C x C x C With One or Two C Side Inlet(s) DWV Tees-Short Design
TABLE 22
DEG. TO MAIN INLET), SINGLE AND DOUBLE SIONS OF SHORT DESIGN DWV TEES WITH SIDE INLET(S)' (45
Size K KK J JJ
3 x 3 x 3 with 2 in. inlet(s) 2.94 1.56 3.06 3.38 3 x 3 x 3 with IYZ in. inlet(s) 2.94 1.56 3.06 3.12
GENERAL NOTE: Dimensions are in inches.
NOTE: (1) To determine whether inlets are right hand or left hand, place the fitting with large side inlet
facing toward you. The side on which the other inlet appears determines its designation.
20
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
ASME 816.23 92 m 07.59670 0524l145 O26 m
CAST COPPER ALLOY SOLDER JOINT DRAINAGE FITTINGS - DWV
C x C X C With One or Two C Side Inlet(s) C x C X C x C With One or Two C Side Inlet (S)
D m Tee-Long Dosign
TABLE 23 DIMENSIONS OF LONG DESIGN DWV TEES
WITH SIDE INLET(S)’ (90 DEG. TO MAIN INLET), SINGLE AND DOUBLE
3 x 3 x 3 with 2 in. Inlet(s) 3 x 3 x 3 with IY’’ in. Inlet(s) 3 x 3 x 3 with 1Y4 in. Inlet(s) 4 x 4 x 4 with 2 in. Inlet(s) 4 x 4 x 4 with 1% in. Inlet(s)
GENERAL NOTE: Dimensions are in inches.
2.94 2.94 2.94 3.88 3.88
NOTE: (1) To determine whether inlets are right hand or left hand,
place the fitting with large side inlet facing toward you. The side on which the other inlet appears determines its designation.
r- “C -7
O C x C x C With One or Two C Side Inlet(s)
C x C x C x C With One or Two C Side Inlet (S)
DWV Tees-Long Design
21
ASME B16.23-1992
TABLE 24 DIMENSIONS OF LONG DESIGN DWV TEES
WITH SIDE INLET(S)‘ (45 DEG. TO MAIN INLET), SINGLE AND DOUBLE
Size JJ
3 x 3 x 3 with 2 in. Inlet(s) 3 x 3 x 3 with lY2 in. Inlet(s)
3.50
GENERAL NOTE: Dimensions are in inches.
3.19
NOTE: (1) To determine whether inlets are right hand or left hand,
place the fitting with large side inlet facing toward you. The side on which the other inlet appears determines its designation.
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
ASME 816.23-1992
ASME B4hS23 92 W 0757670 0524146 Tb2 W
CAST COPPER ALLOY SOLDER JOINT DRAINAGE FITTINGS - DWV
Y cxcxc
cxcxcxc DWV 45 deg. Ys
TABLE 25 DIMENSIONS OF SINGLE AND DOUBLE DWV 45 DEG. Ys
Size L KK K' K Size L KK K' K
1 Y4
2.12 . . . 0.44 1 '/> x 1 Y4 x 1 Y2 4.19 3.88 0.34 . . . 4 X 4 X 2 2.06 2.00 . . . 0.25 lY2 x lY2 x lYa 4.75 4.62 . . . 0.34 4 X 4 X 3 2.19 2.19 . . . 0.38 1 Y2 5.38 5.38 . . . 1.06 4 1.88 1.88 . . . 0.31
3.81 3.38 0.84 . . . 4 X 4 X 1 7 4 1.94 1.94 . . . 0.25 lY2 x lYa x lYa 3.94 3.56 0.66 . . . 4 x 4 x 1Y2 2.06
2 0.36 . . . 2.75 2.75 5
6.69 6.25 . . . 0.06 6 x 6 ~ 4 2.56 2.34 . . . 0.06 2 x 1Y4 x 1% 7.69 7.69 . . . 1.50 6 2.19 2.19 . . . 0.28 2 x 1 Y 2 x 1 Y2
2.53 2.62 . . . 0.53 2 x lY* x 2 5.53 5.12 0.06 . . . 5 X 5 X 3 2.44 2.31 . . . 0.06 2 x 2 x lY4 6.00 5.75 . . . 0.56 5 X 5 X 4 2.56 2.50 . . . 0.22 2 x 2 x lY* 6.50 6.50 . . . 1.19
6 x 6 ~ 3 . . . 0.62 5.62 6.19 3 0.81 . , . 4.12 4.12 6 X 6 X 2 . . . 1.25
7.75 7.75 . . . 0.53 8 x 6 ~ 6 2.19 2.19 0.34 . . . 3 x 1Y2 x lY2 9.22 8.78 . . . 0.53 8 X 8 X 6 2.55 2.44 0.38 . . . 3 x 3 x lY2
10.19 10.19 . . . 1.38 3 2.75 2.75 . . . 0.09 3 X 3 X 2 3.06 2.88 0.38 . . . 3 x 3 x lY4
4.31 3.94 1.25 . . . 6 x 4 ~ 2 3.25 3.00 0.19 . . . 3 x 3 x lY2 5.31 5.31 . . . 0.06 6 X 4 X 4 3.50 3.38 . . . 0.12 3 X 3 X 2 5.69 4.88
GENERAL NOTE: Dimensions are in inches.
22
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
ASME B16.23 92 S 0759670 0524147 9T9 m
CAST COPPER ALLOY SOLDER JOINT DRAINAGE FlITlNGS - DWV
f tï f
K
C x C x F C x F x C DWV 45 deg. Ys
Ï L
I 1-
K .c
TABLE 26 DIMENSIONS OF DWV 45 DEG. Ys
Size L KK K
C x F x F
1 Y4 1 Yz
2 x lYz x 2 2
3 4
0.31 0.38 0.56 0.56 0.81 1 .O6
1.88 2.19 2.75 2.88 4.12 5.38
ASME B16.23-1992
2.75 3.1 2 3.75 3.75 5.69 6.94
GENERAL NOTE: Dimensions are in inches.
DWV Horizontal Twin Branch Tees c x c x c x c
TABLE 27 DIMENSIONS FOR DWV HORIZONTAL TWIN
BRANCH TEES Size A C Min. B
~~
3 x 3 x 1% x 1Y2 3 x 3 x lY4 x lY4
1.88 2.22 2.44 1.83 2.19 2.19
GENERAL NOTE: Dimensions are in inches.
23
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
ASME 816.23-1992
ASME B16.23 92 M 0759b70 0524348 835 m
CAST COPPER ALLOY SOLDER JOINT DRAINAGE FITTINGS - DWV
O
D W Fitting Tees-Single and Double
F T G x C x C F T G x C x C x C
TABLE 28 DIMENSIONS FOR DWV FllTlNG TEES,
SINGLE AND DOUBLE
Size K B A
1 Yz
2.62 2.38 3.75 3 X 3 X 2 2.50 1.88 3.45 2 1.97 1.41 2.78
3 X 3 X l ' / , 3.19 2.16 2.22 3 x 3 x lYa
3.62 2.88 4.94 3 X 2 X 3 3.62 2.88 5.25 3 1.87 2.00 2.72
GENERAL NOTE: Dimensions are in inches.
24
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
CAST COPPER ALLOY SOLDER JOINT DRAINAGE FITTINGS - DWV ASME 816.23-1992
TABLE 29 DIMENSIONS FOR DWV UTILITY TEES
Size D C B A
1 Y2
1.66 0.88 1.66 2.31 2 x 2 x lY2 x lY2
0.81 1.44 2.25 2
1.44 3.19 1.94 1.25 1.94
SENERAL NOTE: Dimensions are in inches.
DWV Utility Tees C x C x C x C
Left Side Inlet F T G x C x C x C
Right Side Inlet F T G x C x C x C
TABLE 30 DIMENSIONS OF DWV FITTING TEES WITH SIDE INLET MAXIMUM
BELOW CENTER LINE Size K D C B A
3 X 3 X 3 X 1 Y 2 3.75 1.75 2.41 2.94 5.25 3 X 3 X 3 X 2 3.75 1.75 2.16 2.94 5.25
GENERAL NOTE: Dimensions are in inches.
25
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
ASME 816.23 92 m 0757b70 0524150 473 m
ASME B16.23-1992 CAST COPPER ALLOY SOLDER JOINT
DRAINAGE FITTINGS - DWV
c x c x c c x c x c x c
c x c x c c x c x c x c
C x C x F C x C x F x F
C x F x C C x F x C x C
TABLE 31 DIMENSIONS OF DWV LONG TURN T-YS, SINGLE AND DOUBLE
Size LL L KK K K JJ
1 Y4
3.81 3.00 1.94 . . . 0.19 2.81 lY2 x lY* x lY4 3.81 3.12 2.1 2 . . . 0.38 3.00 1 Y2 3.94 2.62 1.75 . . . 0.31 2.50
2 4.00 0.56 . . .
. . . . . . 2.44 . . . 0.50 4.00 2 x 1 Y 4 x 2
. . . . . . 2.81 . . . 0.56 4.00 2 x 1Y2X 2
. . . . . . 2.12 . . . 0.06 3.00 2 x 2 x lY4 4.44 3.38 2.38 . . . 0.25 3.44 2 x 2 x 1Y* 4.81 3.62 2.62
3 5.88 0.81 . . . 3.88 5.44 9.00 3 X 3 X 2 4.69 0.09
. . . . . . 2.78 0.41 . . . 3.75 3 X 3 X l ' / ,
. . . . . . 2.88 0.22 . . . 3.94 3 X 3 X l ' / ,
. . . . . . 3.25 . . .
3 ~ 2 x 3 5.88 0.81 * . . 3.44 . . . 3 X 2 X 2 4.50 0.06 . . . 2.75 ... . . . 4 7.75 1 .O6 . . . 5.00 6.69 9.00 4 X 4 X 3 5.62 0.44 . . . 4.50 a . . . . . 4 X 4 X 2 5.12 . . . 0.25
. . . . . . 3.47 0.62 . . . 4.88 4 x 4 x lY2
. . . . . . 3.88
5 9.94 1.25 * . . 6.50 . . . 5 X 5 X 4 8.62 0.59 . . . . . . . . . 5.84 5 X 5 X 3 7.25 . . . 0.06 5.1 9 . . . . . . 6 11 -81 1.53 . . . 7.78 6 x 6 ~ 5 10.44 0.88 . . . 7.09 6 x 6 ~ 4 9.09 0.19 . . . 6.34 . . . . . . 6 x 6 ~ 3 7.69 . . . 0.50 5.69 . . . . . .
* . .
I . .
. . . * . . . . . . . .
GENERAL NOTE: Dimensions are in inches.
Y
2.50 3.00 2.62
4.00 3.19 2.69 4.00 4.00
5.88 4.1 2 3.25 2.81 5.88 4.00
7.75 5.1 2 4.25 3.62
9.78 7.97 6.16
11.62 9.78 7.91 6.12
26
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
ASME B l b . 2 3 72 m 0759b70 0524151 3 Z T
CAST COPPER ALLOY SOLDER JOINT DRAINAGE FITTINGS - DWV
t"J--"J"!
ASME 016.23-1992
C x C x F x F DVW Double Short T - Y
1' O Size J K
2 x lY2 x lY2 x lY2 3.06 3.19
c x c x c x c DWV Double Short T-Y
TABLE 32 TABLE 33 DIMENSIONS OF DWV DOUBLE SHORT T-Y DIMENSIONS OF D W DOUBLE SHORT T-Y
TI 2 x 2 x lY2 x lY2 2 X l ' / , X 2 X 2 2 x lY2 x IY, x IV4
GENERAL NOTE: Dimensions are in inches.
L Size J K
3.25 1 Y, 2.51 3.26 3.66 2 3.38 4.09 4.1 9 2 x 2 x lY2 x IV2 2.78 3.62 3.56 2 x 1 Y 2 x 2 x 2 3.00 4.19
2 x lY2 x lY2 x lY2 2.38 3.19 3 4.44 5.66
GENERAL NOTE: Dimensions are in inches.
L
3.29 4.00 3.68 4.19 3.25 5.75
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
ASME 816.23-1992 CAST COPPER ALLOY SOLDER JOINT
DRAINAGE FlTlNGS - DWV
DWV 90 deg. Elbow With High Heel Inlet
c x c x c
DWV 90 deg. Elbow With Low Heel Inlet
c x c x c
DWV 90 deg. Elbow With Side Inlet
c x c x c
TABLE 34 DIMENSIONS OF DWV ELBOW WITH INLETS
Size L 2 Y X K
3 X 3 X 2
1.50 1.69 1.69 2.94 3 x 3 x 1 Y e 1.19 1.50 1.69 1.69 2.94 3 x 3 x lYz 1.28 1.50 1.69 1.69 2.94
1.12
4 X 4 X 2 3.88 2.12 1.28 2.00 2.25 2.06 3.88 4 X 4 X 1Y2 1.88 2.00 2.25
GENERAL NOTE: Dimensions are in inches.
28
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
ASME 836.23 92 W 0757b70 0524353 l T 2 W
CAST COPPER ALLOY SOLDER JOINT DRAINAGE FITTINGS - OWV
TABLE 35 DIMENSIONS OF DWV DOUBLE BRANCH SINK FITTINGS
ASME 616.23-1992
GENERAL NOTE: Dimensions are in inches.
TABLE 36 DIMENSIONS OF D W CLOSET
OFFSET FITTINGS
4.1215 min. 4.1270 max. 4.1215 min. 4.1 270 max.
4 x 3 2.50 1.44
GENERAL NOTE: Dimensions are in inches. FTG x C
29
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
ASME BI16923 92 m 0759b70 0 5 2 4 3 5 4 039
ASME B16.23-1992
L N 4
DWV 90 deg. Closet Elbow FTG x C
CAST COPPER ALLOY SOLDER JOINT DRAINAGE FITTINGS - DWV
TABLE 37 DIMENSIONS OF DWV 90 DEG. CLOSET
ELBOW Size
4
3
4 x 3
K
3.88
2.94
2.88
N
Floor Flange Vent Support (May be Round or Oval Design)
TABLE 38 DIMENSIONS OF FLOOR FLANGE VENT SUPPORT
4.1215 min. 4.1270 max.
3.1215 min. 3.1270 max.
4.1215 min. 4.1270 max.
1 Ya 1 Y2 2 3
2.62
0.75 3.94 3.38 2 0.22 0.19 0.69 3.05 2.62 2 0.22 0.19 0.62 3.06
2 0.25 0.19 0.94 5.12 4.50 2 0.22 0.19
G
4.44
3.50
3.72
O
O
a
m 4
4 0.56 0.62 2.12 1 1 .o0 10.00 8 4 0.56 0.50 1.69 9.00 7.88 6 4 0.44 0.38 1.44 8.00 6.94 5 2 0.25 0.19 1.19 6.12 5.50
GENERAL NOTE: Dimensions are in inches.
30
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
ASME Blb.23 92 0759670 0524355 T75 m
CAST COPPER ALLOY SOLDER JOINT DRAINAGE FITTINGS - DWV
h
ASME B16.23-I992
0.56 min.
FTG x C With One or Two C Side Inlet(s)
DWV-90 deg. Closet Elbows
TABLE 39 DIMENSIONS OF D W CLOSET ELLS WITH SIDE INLET(S)'
(90 DEG. AND 45 DEG.) TO MAIN INLET(S) Size N H F E D C B A
4 x 3 with 1Y2 in. inlet(s) 1.72 2.81 4.03 0.56 3.62 3.88 4.44 4.123 min. 4.127 max.
4.123 min. 4.1 27 rnax.
4 x 4 with I'/* in. inlet(s)
GENERAL NOTE: Dimensions are in inches.
2.09 2.81 4.22 1.00 3.81 3.88 4.44
NOTE: (1) To determine whether inlets are right hand or left hand, place the fitting with large inlet up and toward you. The side on
which the other inlet appears determines its designation.
31
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
ASME Blb.23 72 8759670 0524156 701
ASME B16.23-1992
"-1-n ,
CAST COPPER ALLOY SOLDER JOINT DRAINAGE FITTINGS - DWV
7- ' e- l
A
DWV 90 deg. Closet Elbows
f
TABLE 40 DIMENSIONS OF DWV CLOSET ELLS WITH OR WITHOUT SIDE INLET(S)' (90 DEG.
AND 45 DEG.) TO MAIN INLET(S)
Size N K H G F E D C B A Min.
4 x 32
4.123 min. 3.18 . . . . . . . . . . . . . . . . . . 14.00 4.44 4 x 4
4.123 min. 3.18 . . . . . . . . . * . . . . . . . . 14.00 4.44 4 x 3 with lY2 in. inlet(s)2 4.127 max. 3.18 1.72 4.69 2.94 4.03 0.56 3.62 14.00 4.44
4 x 4 with lY2 in. inlet(s) 4.44
NOTES:
GENERAL NOTE: Dimensions are in inches.
4.127 max. 3.18 2.09 4.56 2.81 4.22 1.00 3.81 14.00
(1) To determine whether inlets are right hand or left hand, place the fitting with large inlet up and toward you. The side on
(2) Closet flange attaches to 4 in. end. which the other inlet appears determines its designation.
32
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
ASME 816.23 92 m 0759670 0524357 848 m
CAST COPPER ALLOY SOLDER JOINT DRAINAGE FITTINGS - DWV
stop opt¡
ASME 816.23-1992
O .62
0.38
- 15 des.
Alternate Slot Design Full Slot Half Slot
Suggested Slot Arrangements
TABLE 41 DIMENSIONS OF DWV CLOSET FLANGES’
D Outside diameter of flange, max. 7.00 DD Diameter of center line of slots 6.00 E Inside diameter of 4 in. flange (W 3.94
EE Inside diameter of 3 in. flange 4.1 2 UU Length of 3 in. flange 1.69
V Bore of tube stop in 3 in. flange 2.94
tube stop is used)
GENERAL NOTES: Dimensions are in inches.
NOTES: (1) 45 deg. angle may be extended to face of flange. (2) Optional: (a) the addition of 0.30 diam. holes with or
without countersink on bolt circle DD and/or (b) two 0.38 wide notches on center line extending from outer edge of flange.
33
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
ASME 616.23-1992
ASflE Rlb.23 92 0759670 0524158 784
CAST COPPER ALLOY SOLDER JOINT DRAINAGE FllTlNGS - DWV
e
f
!- X
t
Vent Tees and Vent Double Tees Vent Increasers With Side Inlets
C x C x C a n d C x C x C x C
0 0 0 a l @ @ @
TABLE 42 DIMENSIONS OF VENT TEES
AND VENT DOUBLE TEES
Size
1 Ya 1 Y2 lYz x lY2 x 1%
2 2 X 2 X l ’ / , 2 x 2 x lY4
3 3 X 3 X 2 3 x 3 x 1Y2 3 x 3 x lY4
3 X 4 X 2 3 x 4 x lYz
GENERAL NOTES: (a) Dimensions are in inches.
H
0.87 1 .o0 0.87
1.25 1 .o0 0.87
1.75 1.25 1 .o0 0.87
1.19 1 .O6
J
0.87 1 .o0 1 .o0
1.25 1.25 1.25
1.75 1.75 1.75 1.75
2.19 2.1 2
X
0.87 1 .o0 0.87
1.25 1 .o0 0.87
1.75 1.25 1 .o0 0.87
1.19 1 .o0
(b) Vent fittings are designed for dry vents only. They are not specified for waste lines. Vent fittings must be marked as follows: VENT ONLY.
34
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
CAST COPPER ALLOY SOLDER JOINT DRAINAGE FITTINGS - DWV
tK-i
ASME 616.23-1992
Vent Elbows c x c
DWV Stack Upturns, Single and Double
C x C x C a n d C x C x C x C
TABLE 43 DIMENSIONS OF VENT
ELBOWS
TABLE 44 DIMENSIONS OF DWV STACK
UPTURNS, SINGLE AND DOUBLE
Size
1.25 1.75
GENERAL NOTES: (a) Dimensions are in inches. (b) Vent fittings are designed for
dry vents only. They are not specified for waste lines. Vent fittings must be marked as fol- lows: VENT ONLY.
2 2 x 2 x IV2 2 x 1Y2 x IV*
3 3 X 3 X 2 3 X 3 X IV2 4 X 4 X 3
3.25 2.56 2.38
5.09 3.44 2.69 5.03
3.50 3.12 2.75
3.75 3.41 3.16 4.25
4.72 3.84 3.47
5.69 4.19 3.44 5.66
GENERAL NOTE: Dimensions are in inches.
35
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
ASME 816.23-1992
For slip joint threads See Table 48.
DWV Slip Joint Thread Pieces C X S J
TABLE 45 DIMENSIONS OF SLIP
JOINT PIECES j' Size
1 Y4 x 1 Y2 0.38 0.38
GENERAL NOTE: Dimensions are in inches.
CAST COPPER ALLOY SOLDER JOINT DRAINAGE FIXINGS - DWV
- A *
DWV Trap Coupling C x O.D. Tube
TABLE 46 DIMENSIONS OF TRAP COUPLING
13: x lY4 O.D. lY2 x lY2 O.D. lY2 X lY4 O.D. 2 x lY2 O.D. 0.41
GENERAL NOTE: Dimensions are in inches.
36
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
ASME 816.23 92 m 0759670 0524LbL 279 m
CAST COPPER ALLOY SOLDER JOINT DRAINAGE FllTlNGS - DWV
DWV Trap Extended Bushing FTG x Outside Diameter of Tube (FTG x O.D. Tube)
0.31 min. A- 4 i I L
O
ASME B1 6.23-1 992
TABLE 47 DIMENSIONS OF TRAP EXTENDED BUSHINGS
Size B A
1% x lY4 O.D. 1.50 0.75 1Y2 x 1Y2 O.D. 1.25 0.75
GENERAL NOTE: Dimensions are in inches.
Fitting !LI
Gasket (1)
DWV Slip Joint Ends
0.53 min. 0.44 min.
O TABLE 48
DIMENSIONS OF SLIP JOINT ENDS
1 Y2 NPSM 2 NPSM
GENERAL NOTE: Dimensions are in inches.
NOTES: (1) Gasket to be pliable material not subject to aging or
(2) Nut may be any material specified in Section 7, or other
(3) Angles must be equal.
drying out.
suitable nonferrous alloy.
37
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
ASME B16. 23-1 992
tG1
DWV Cap C
TABLE 49 DIMENSIONS OF D W CAP
Size T G
1 ‘/A
0.120 1 .o0 4 0.120 0.75 3 0.100 0.62 2 0.1 O0 0.56 1 ’/= o. 1 O0 0.50
GENERAL NOTE: Dimensions are in inches.
CAST COPPER ALLOY SOLDER JOINT DRAINAGE FliTlNGS - DWV
DWV Fitting Plug FTG
TABLE 50 DIMENSIONS OF D W PLUGS
Size
0.100 0.62 o. 1 O0 0.69 0.100 0.81 0.1 20
GENERAL NOTE: Dimensions are in inches.
38
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
CAST COPPER ALLOY SOLDER JOINT DRAINAGE FITTINGS - DWV
Type
c x c C x F c x c C x F
c x c c x c C x F c x c
c x c
GENERAL
NOTE:
Drum I Pipe and Size Tubing Size
4 x 5
4 x 5 4 x 8 4 x 5 1% 4 x 5 1%
IOTE: Dimensions are in
C x F C X C
D W One Piece Drum Traps
TABLE 51 DIMENSIONS OF DWV DRUM TRAPS Plug Size
Iches. I A
1.50 1.50 1.50 2.00
2.00 2.00 2.00 2.00
B
1.72 1.72
1.22
1.22
1.22 1.22
. . .
. . .
ASME 816.23-1992
C
2.97 . . . . . . . . . . . . . . . . . . . . .
D
. . . 3.22
3.25
. . . 3.25 . . .
E
. . .
. . . 3.88 . . . . . . 4.72 . . . . . .
F Max.
. . .
. . . 6.75 . . .
. . . 8.00 . . . . . .
(1) Trap seal is 2 in. minimum.
39
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
ASME 816.23-1992
ASME BLb.23 92 I 0759b70 0524164 T88 W
CAST COPPER ALLOY SOLDER JOINT DRAINAGE FITTINGS - DWV
O
l F
c x c DWV Swivel Drum Traps
TABLE 52 DIMENSIONS OF DWV SWIVEL DRUM TRAP
c x c c x c c x c c x c
Size Size Size
4 x 8 3 x 6 4 x 8
F Max.
2.00 4.72 8.00 1.50 3.66 6.66 2.00 4.34 7.78
GENERAL NOTE: Dimensions are in inches.
NOTE: (1) Trap seal is 2 in. minimum.
40
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
CAST COPPER ALLOY SOLDER JOINT DRAINAGE FITTINGS - DWV ASME B16.23-1992
Without Cleanout With or Without Cleanout S J X C c x c
D W P-Trap With Union Joint DWV One Piece P-Trap DWV One Piece Line P-Trap S J X C S J X C C X C
O TABLE 53
DIMENSIONS OF DWV TRAPS Description I Size
P-Trap SJ x C with or without cleanout
2 Running P-Trap C x C with or without cleanout 1 Y2 P-Trap C x C with or without cleanout 1 Y4
P-Trap Swivel SJ x C P-Trap Swivel SJ x F 1 Y>
P-Trap One Piece S C P-Trap One Piece C C 1 Y2 GENERAL NOTE: Dimensions are in inches.
NOTE:
1 Ya
2
F i 2.44
K D C Min.
1.19 1.44 1.94 1.12
1.12 1.47
1.44
3.28 3.53 4.25 3.16
3.44 3.91
3.53
. . .
. . . 1.94
1.94 2.81
. . .
. . .
O (1) Trap seal is 2 in. minimum (all traps).
41
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
ASME 616.23-1992 CAST COPPER ALLOY SOLDER JOINT
DRAINAGE FITTINGS - DWV
TABLE 54 DIMENSIONS OF DWV TEST TEES WITH PLUG
1% x lYa.X 1% lY2 x l x x lY2 2 X 2 X 2 3 X 3 X 3 3.88 4 X 4 X 4
GENERAL NOTE: Dimensions are in inches. DWV Test Tees Wi th Plug
C x C x F
c Across flats
One to two threads large, hand tight.
TABLE 55 DIMENSIONS OF D W PLUGS
Size B A
1 Y4
0.75 1.75 8 0.72 1.53 6 0.69 1.44 5 0.66 1.38 4 0.62 1.31 3 0.53 1 .o9 2 0.50 1 .o0 1 Y2 0.44 0.88
GENERAL NOTE: Dimensions are in inches.
42
C
0.88 1 .o0 1.12 1.38 1.38 1.50 1.50 1.75
O
O
O
O
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
ASME 836.23 92 m 0757670 0524367 797 m
CAST COPPER ALLOY SOLDER JOINT DRAINAGE FllTlNGS - DWV ASME B16.23-1992
ANNEX A
References
(This annex is an integral part of ASME B16.23 and is placed after the main text for convenience.)
The following is a list of standards and specifications referenced in this Standard, showing the year of approval.
ASME Publications (Approved as American National Standards)
ANSUASME B1.20.1-1983 Pipe Threads, General Purpose (Inch) ASME B16.12-1991 Cast-Iron Threaded Drainage Fittings ANSI B16.18-1984 Cast Bronze Solder Joint Pressure Fittings
ASTM Publications
ASTM A74-1987 Specification for Cast Iron Soil Pipe and Fittings ASTM B62-1990 Specification for Composition Bronze or Ounce Metal
Castings ASTM B306-1988 Specification for Copper Drainage Tube (DWV) ASTM B.584-1990 Specification for Copper Alloy Sand Castings for General
Applications
Publications of the following organizations appear on the above list:
ASME The American Society of Mechanical Engineers 345 East 47th Street, New York, NY 10017
ASTM The American Society for Testing and Materials 1916 Race Street, Philadelphia, PA 19103
Publications appearing above which have been approved as American National Standards may also be obtained from:
ANSI American National Standards Institute, Inc. 11 West 42nd Street, New York, Ny 10036
43
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
ASME B36.23 92 W 0757670 0524368 6 2 3 m
AMERICAN NATIONAL STANDARDS FOR PIPING. PIPE FLANGES. FITTINGS. AND VALVES
Scheme for the Identification of Piping Systems ............................................ A13.1-1981(R1985) Pipe Threads. General Purpose (Inch) .................................................... B1.20.1-1983(R1992) Dryseal Pipe Threads (Inch) .............................................................. B1.20.3-1976(R1991) Cast Iron Pipe Flanges and Flanged Fittings ....................................................... 816.1-1989 Malleable Iron Threaded Fittings. Class 150 and 300 ............................................... 816.3-1985 Cast Iron Threaded Fittings. Classes 125 and 250 .................................................. B16.4-1985 Pipe Flanges and Flanged Fittings ................................................................ 816.5-1988 Factory-Made Wrought Steel Buttwelding Fittings ................................................. B16.9-1986 Face-to-Face and End-to-End Dimensions of Valves .............................................. B16.10-1986 Forged Fittings. Socket-Welding and Threaded ................................................... 816.11-1991 Cast Iron Threaded Drainage Fittings ............................................................ 816.12-1991 Ferrous Pipe Plugs. Bushings, and Locknuts with Pipe Threads .................................... B16.14-1991 Cast Bronza Threaded Fittings. Class 125 and 250 ................................................ 816.15-1985 Cast Copper Alloy Solder Joint Pressure Fittings ................................................. 816.18-1984 Ring-Joint Gaskets and Grooves for Steel Pipe Flanges ........................................... 816.20-1973 Nonmetallic Flat Gaskets for Pipe Flanges ....................................................... B16.21-1978 Wrought Copper and Copper Alloy Solder Joint Pressure Fittings ................................. 816.22-1989 Cast Copper Alloy Solder Joint Drainage Fittings - DWV ......................................... 816.23-1992
1500. and 2500 ............................................................................ 816.24-1991
Cast Copper Alloy Fittings for Flared Copper Tubes .............................................. B16.26-1988 Wrought Steel Buttwelding Short Radius Elbows and Returns ..................................... B16.28-1986 Wrought Copper and Wrought Copper Alloy Solder Joint Drainage Fittings - DWV ................ B16.29-1986 Cast Copper Alloy Solder Joint Fittings for Sovent@ Drainage Systems ............................. B16.32-1992
Valves - Flanged. Threaded. and Welding End .................................................. 816.34-1988 Orifice Flanges ................................................................................ 816.36-1988 Large Metallic Valves for Gas Distribution (Manually Operated. NPS 2'4 to 12. 125 psig Maximum) . . . 816.38-1985 Malleable Iron Threaded Pipe Unions. Classes 150. 250. and 300 .................................. 816.39-1986 Manually Operated Thermoplastic Gas Shutoffs and Valves in Gas Distribution Systems ............. 816.40-1985
for Nuclear Power Plants ............................................................ B16.41-1983(R1989) Ductile Iron Pipe Flanges and Flanged Fittings. Class 150 and 300 ................................. 816.42-1987 Wrought Copper and Copper Alloy Solder Joint Fittings for Sovent" Drainage Systems . . . . . . . . . . . . . 816.43-1982 Cast Iron Fittings for SovenP Drainage Systems ................................................. 816.45-1987 Large Diameter Steel Flanges (NPS 26 Through NPS 60) .......................................... 816.47-1990
Chemical Plant and Petroleum Refinery Piping .................................................... 831.3-1990
Anhydrous Ammonia. and Alcohols .......................................................... B31.4-1989 Refrigeration Piping ............................................................................. 831.5-1987 Gas Transmission and Distribution Piping Systems ................................................ 831.8-1989 Building Services Piping ......................................................................... 831.9-1988 Slurry Transportation Piping Systems ........................................................... B31.11-1989
Welded and Seamless Wrought Steel Pipe ..................................................... B36.10M-1985 Stainless Steel Pipe .......................................................................... B36.19M-1985
Cast Copper Alloy Pipe Flanges and Flanged Fittings. Class 150. 300. 400. 600. 900.
Buttwelding Ends .............................................................................. 816.25-1986
Manually Operated Metallic Gas Valves for Use in Gas Piping Systems Up to 125 psig (Sizes'/, Through 2) ....................................................................... 816.33-1990
Functional Qualification Requirements for Power Operated Active Valve Assemblies
Power Piping ................................................................................... 831.1-1989 Fuel Gas Piping ................................................................................. 831.2-1968
Liquid Transportation Systems for Hydrocarbons, Liquid Petroleum Gas,
ASME Guide for Gas Transmission and Distribution Piping Systems - 1986 (not an ANSI Standard) ............. Manual for Determining the Remaining Strength of Corroded Pipelines (not an ANSI Standard) ....... B31G-1991
Self-operated and Power-Operated Safety-Related Valves Functional Specification Standard . . N278.1-1975(R1984)
The ASME Publications Catalog shows a complete list of all the Standards published by the Society . For a compli- mentary catalog. or the latest information about our publications. call 7-800-THE-ASME (7.800.843.2763) .
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services
COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services