arcat · web viewsection 08410. folding glazed wall systems - exterior and interior. display hidden...

SECTION 08410 (08 41 00)FOLDING GLAZED WALL SYSTEMS - EXTERIOR AND INTERIOR

Display hidden notes to specifier. (Don't know how? Click Here)

Copyright 2010 - 2019 ARCAT, Inc. - All rights reserved

PART 1 GENERAL

1.1 SECTION INCLUDES

A. Folding Glazed Wall Systems:1. Aluminum-framed folding systems. (SL45)2. Thermally-broken, aluminum-framed folding systems. (SL60 and SL70)3. Thermally-broken, sliding-folding aluminum-framed systems. (SL84)4. Thermally broken, sliding-folding acoustically rated, aluminum-framed system. (SL64

Acoustical)

1.2 RELATED SECTIONS

A. Section 06100 - Rough Carpentry; wood framing R.O. and blocking.

B. Section 06200 - Finish Carpentry.

C. Section 07270 - Air Barriers; building paper and building wrap.

D. Section 07620 - Sheet Metal Flashing and Trim; flashing gutters, and other sheet metal work.

E. Section 07900 - Joint Protection.

F. Section 08400 - Entrances and Storefronts.

G. Section 08415 - Single Track Glazed Wall Systems - Exterior and Interior.

H. Section 08450 - All-Glass Entrances and Storefronts.

I. Section 08490 - Sliding Storefronts.

J. Section 08495 - Folding Glass Wall System.

K. Section 08520 - Aluminum Windows.

L. Section 08700 - Hardware.

M. Section 08800 - Glazing; schedule of glazing.

N. Section 09110 - Non-Load Bearing Wall Framing; metal framing R.O. and reinforcement.

O. Section 10660 - Glass Partition System.

1.3 REFERENCES

08410 -1

A. American Architectural Manufacturer's Association (AAMA):1. AAMA 502 - Voluntary Specification for Field Testing of Newly Installed Fenestration

Products.2. AAMA 520 - Voluntary Specification for Rating the Severe Wind-Driven Rain

Resistance of Windows, Doors and Unit Skylights.3. AAMA 611 - Voluntary Specification for Anodized Architectural Aluminum.4. AAMA 920, Operation / Cycling Performance.5. AAMA 1303.5 - Voluntary Specifications for Forced-Entry Resistant Aluminum Sliding

Glass Doors.6. AAMA 1304 - Voluntary Specification for Determining Forced Entry Resistance of

Side-Hinged Door Systems.7. AAMA 2604 - Voluntary Specifications, Performance Requirements and Test

Procedures for High Performance Organic Coatings on Aluminum Extrusions and Panels.

8. AAMA 2605, Voluntary Specifications, Performance Requirements and Test Procedures for Superior Performing Organic Coatings on Aluminum Extrusions and Panels.

9. AAMA CAWM 300, Forced Entry Resistance for Sliding Glass Doors.10. AAMA/WDMA/CSA 101/I.S.2/A440, NAFS, North American Fenestration Standard -

Specification for Windows, Doors and Skylights.

B. American National Standards Institute: ANSI Z97.1 - For Safety Glazing Materials Used in Buildings - Safety Performance Specifications and Methods of Test.

C. ASTM International (ASTM):1. ASTM C1036 - Standard Specification for Flat Glass.2. ASTM C1048 - Standard Specification for Heat-Strengthened and Fully Tempered

Flat Glass.3. ASTM E90- Standard Test Method for Laboratory Measurement of Airborne Sound

Transmission Loss of Building Partitions and Elements.4. ASTM E283 - Test Method for Rate of Air Leakage through Exterior Windows, Curtain

Walls, and Doors by Uniform Static Air Pressure Difference.5. ASTM E330 - Test Method for Structural Performance of Exterior Windows, Curtain

Walls, and Doors by Uniform Static Air Pressure Difference.6. ASTM E331 - Standard Test Method for Water Penetration of Exterior Windows,

Skylights, Doors, and Curtain Walls by Uniform Static Air Pressure Difference.7. ASTM E413 - Classification for Rating Sound Insulation.8. ASTM E547 - Test Method for Water Penetration of Exterior Windows, Curtain Walls,

and Doors by Cyclic Static Air Pressure Differential.9. ASTM E1332, Standard Classification for Rating Outdoor-Indoor Sound Attenuation.10. ASTM E2268, Standard Test Method for Water Penetration of Exterior Windows,

Skylights, and Doors by Rapid Pulsed Air Pressure Difference.11. ASTM F842- Standard Test Methods for Measuring the Forced Entry Resistance of

Sliding Door Assemblies.

D. British Standards Institution (BSI Group): PAS 24 (Publicly Available Specification), Enhanced security performance requirements for door assemblies.

E. California Association of Window Manufacturers (CAWM): CAWM 300 - Forced Entry Resistance Tests for Sliding Glass Doors.

F. Construction Products Directive (CPD): CE Mark.

G. Consumer Product Safety Commission (CPSC): CPSC 16CFR-1201, Safety Standard for Architectural Glazing Materials.

H. German Institute for Standardization (DIN):

08410 -2

1. DIN EN 1191 - Windows and Pedestrian Doors - Mechanical Durability Test Method.2. DIN EN ISO 717-1 - Acoustics - Rating of sound insulation in buildings and building

elements.3. DIN EN 1627 - Pedestrian door sets, windows, curtain walling, grilles and shutters -

Burglar resistance - Requirements and classification.4. DIN EN 1630 - Pedestrian door sets, windows, curtain walling, grilles and shutters -

Burglar resistance - Test method for the determination of resistance to manual burglary attempts.

5. DIN EN ISO 10140-1, 2, 4 and 5 - Airborne sound measurement.6. DIN EN ISO 12400, Windows and pedestrian doors - Mechanical durability -

Requirements and classification.7. DIN 52210-4, Tests in Building Acoustics - Airborne and Impact Sound.

I. Florida Building Code: TAS 202 - Criteria for Testing Impact and Non-Impact Resistant Building Envelope Components Using Uniform Static Air Pressure.

J. International Organization for Standardization (ISO):1. ISO 9001 - Quality management systems.2. ISO 14001 - Environmental management systems.

K. National Fenestration Rating Council (NFRC):1. NFRC 100 - Procedure for Determining Fenestration Product U-factors.2. NFRC 200 - Procedure for Determining Fenestration Product Solar Heat Gain

Coefficient and Visible Transmittance at Normal Incidence.3. NFRC 400 - Procedure for Determining Fenestration Product Air Leakage.4. NFRC 500 - Procedure for Determining Fenestration Product Condensation

Resistance Rating Values.

L. U.S. Environmental Protection Agency (EPA): Energy Star program.

1.4 SUBMITTALS

A. Submit under provisions of Section 01300.

B. Product Data: Manufacturer's data sheets on each product to be used, including:1. Preparation instructions and recommendations.2. Storage and handling requirements and recommendations.3. Independently tested data listing performance criteria.4. Product literature for systems incorporated in the Work. Performance test results and

details of construction relative to materials, dimensions of individual components, profiles, and colors.

5. Manufacturers' Instructions: Submit Owner's Manual from manufacturer which includes installation instructions, operation and maintenance data.

6. Certificates: Submit CE Mark Certificate.

C. Product Drawings: Including but not limited to the following.1. Indicate system component sizes, dimensions and framing R.O., configuration, swing

panels, direction of swing, stacking layout, typical head jamb, side jambs and sill details, type of glazing material, handle height and field measurements.

2. Elevations of rough opening requirements and details for field-applied components.

D. Contract Closeout Submittal: Owner's Manual from manufacturer. Identify Owner's Manual with project name, location and completion date, type and size of unit installed.

1.5 QUALITY ASSURANCE

A. Regulatory Requirements: CE Mark certified.

08410 -3

B. Manufacturer: Complete, precision built, engineered, pre-fitted units by a single source manufacturer with 30-year experience in providing folding and sliding door systems for large openings in the North American market.1. ISO 9001: 2015 quality management system registration.2. ISO 14001: 2015 environmental management system registration.

C. Installer Qualifications:1. Experienced in installation of manufacturer's products or similar products.2. Reference list of 3 projects of similar scale and complexity successfully completed in

the last 3 years.3. Project names, locations, completion dates, names and telephone numbers of

General Contractor and Owner's contact person.4. Installer trained and certified by manufacturer.

D. Single Source: Furnish system materials from one manufacturer for entire Project.

1.6 DELIVERY, STORAGE, AND HANDLING

A. Deliver materials to job site in sealed, unopened cartons or crates.1. Upon receipt, inspect shipment. Ensure it is complete, in good condition and meets

project requirements.

B. Store products in manufacturer's unopened packaging until installation. Store flat in well ventilated area, no direct sunlight, in a clean and dry location. Protect units against weather and defacement or damage from construction activities, especially to panel edges.

1.7 PROJECT CONDITIONS

A. Mark field measurements on Product Drawing submittal. Contractor shall field verify dimensions including but not limited to rough openings and inset components.

B. Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's recommended limits.

1.8 WARRANTY

A. Manufacturer's warranty against defects in materials and workmanship and as follows:1. Rollers: 10 years.2. Seal Failure of Insulated Glazing: 10 years.3. Other Components (excluding screens): Five years beginning with the earliest of 120

days from date of delivery by manufacturer or date of Substantial Completion.4. Other Components (excluding screens): 10 years beginning with the earliest of 120

days from date of delivery by manufacturer or Date of Substantial Completion if installed by manufacturer's specific system approved or certified trained installer.

PART 2 PRODUCTS

2.1 MANUFACTURERS

A. Acceptable Manufacturer: Nana Wall Systems, Inc., which is located at: 100 Meadow Creek Dr. Suite 250; Corte Madera, CA 94925; Toll Free Tel: 800-873-5673; Tel: 415-383-3148; Fax: 415-383-0312; Email:request info ([email protected]); Web:https://www.nanawall.com

B. Substitutions: Not permitted.

C. Requests for Substitutions: Considered in accordance with provisions of Section 01600.

08410 -4

2.2 ALUMINUM-FRAMED FOLDING GLASS WALL SYSTEM

A. Basis of Design: Model SL45 Aluminum Folding Glass Wall Systems manufactured by Nana Wall Systems, Incorporated. Top-hung system for straight runs, segmented angle changes, and center pivot. Manufacturer's standard frame and panel profiles, with head and floor tracks, side jambs and panels with dimensions as shown on Drawings.1. System Components: Aluminum frame, threshold, panels, sliding-folding and locking

hardware, weather stripping, glass and glazing, and, accessories as required for a complete working installation.a. Insect Screen: Fully retractable non-pleated screen. Ultra-strong, UV resistant

fiberglass mesh housed in single cartridge riding on a single track.1) Basis-of-Design Product by Manufacturer: The Horizon by Wizard

Industries, Inc.

B. Performance Criteria: Lab tested.1. Standard Sill - Inward or Outward Opening.

a. Air Infiltration per ASTM E283: At static air pressure difference of 1.6 psf (75 Pa): 0.27 cu ft per min per sq ft (1.38 L per sec per sq m).

b. Water Penetration per ASTM E331, ASTM E547: Weep holes by others. No uncontrolled water leakage at static test pressure of 1.56 psf (75 Pa).

2. Low Profile Saddle Sill - Inward or Outward Opening.a. Air Infiltration per ASTM E283: At static air pressure difference of 1.6 psf (75

Pa): 0.25 cu ft per min per sq ft (1.28 L per sec per sq m).b. Water Penetration per ASTM E331, ASTM E547: Weep holes by others. No

uncontrolled water leakage at static test pressure of 3.76 psf (180 Pa).3. Flush Sill - Inward or Outward Opening.

a. Air Infiltration per ASTM E283: At static air pressure difference of 1.6 psf (75 Pa): 0.25 cu ft per min per sq ft (1.28 L per sec per sq m).

4. ADA Compliant Flush Sill - Inward or Outward Opening.a. Air Infiltration per ASTM E283: At static air pressure difference of 1.6 psf (75

Pa): 0.25 cu ft per min per sq ft (1.28 L per sec per sq m).5. Structural Load Deflection per ASTM E330:

a. Load Structure: At 1.5 times design wind pressure with no glass breakage or permanent damage to fasteners or storefront components.

b. Design Pressure Positive and Negative: 35 psf (1675 Pa).6. Forced Entry per AAMA 1303.5 and AAMA CAWM 300: Meets requirements.7. Swing Panel - Operation / Cycling Performance per AAMA 920: 500,000 cycles.8. Thermal Performance U-factor: NFRC 100 rated, certified and labeled (shown in

manufacturer's latest published data for glazing and sill specified).9. Solar Heat Gain Coefficient plus Visible Light Transmission: NFRC 200 rated, certified

and labeled.10. Florida Product Approval for Wind Loading: Units tested to AAMA 101/I.S.2/A440 and

approved according to the Florida Building Code 2014, Section 1710.5, for panel sizes subject to manufacturer size charts.a. Product Approval Number: FL24518: Units with panel sizes up to 43 inch (1.07

m) wide x 120 inch (3.05 m) high; subject to manufacturer size chart.11. Acoustic Performance: STC (Rw).

a. STC (Rw) 36 (36) and OITC 32 with 1/2 inch (12 mm) STC 39 laminated glass.b. STC (Rw) 35 (35) and OITC 30 with 5/16 inch (8 mm) STC 37 laminated glass.c. STC (Rw) 30 (31) and OITC 27 with 1/4 inch (6 mm) STC 32 tempered glass.d. System STC (Rw) 35 (35) with 5/16-inch (8 mm) STC 37 enhanced laminated

glass.e. System STC (Rw) 34 (34) with 1/4 inch (6 mm) STC 36 enhanced laminated

glass.f. System STC (Rw) 33 (33) with 1/4 inch (6 mm) STC 35 laminated glass.g. System STC (Rw) 30 (30) with 1/4 inch (6 mm) STC 31 tempered glass.

08410 -5

C. Design Criteria:1. Sizes and Configurations: Refer to Drawings for custom dimensions within maximum

frame sizes indicated in manufacturer's literature. Refer to Drawings for number of panels and configuration.

2. Unit Operation: Sliding and folding hardware with top and bottom tracks.3. System Operation: Folding panel system.4. System Operation: Paired panel system.5. Panel Configuration: Straight.6. Panel Configuration: Segmented curve.7. Panel Configuration: 90 degree angle turn.8. Panel Configuration: 135 degree angle turn.9. Panel Configuration: Window and door combination.10. Panel Operation: Inward opening unit. Stack Storage Configuration: Inside jamb.11. Panel Operation: Outward opening unit. Stack Storage Configuration: Outside jamb.12. Panel Operation: Center pivoted unit. Stack Storage Configuration: Center pivot.13. Panel Operation: Inward/outward combination opening unit. Stack Storage

Configuration: Inside-outside combination.14. Panel Operation: Fold flat, against wall, full 180 degrees movement of door panel

stack. Stack Storage Configuration: Fold flat against wall.15. Mounting, Top Hung: For each pair of folding panels, cardanic, independently

suspended, four wheeled upper running carriage and lower guide carriage. Coated with fiberglass reinforced polyamide.

16. Panel Type: Hinged.17. Panel Type: Unhinged.18. Primary Swing Panel of Paired Swing Panels: Swing Direction: Looking from inside.

a. Primary Swing Panel: On the left.b. Primary Swing Panel: On the right.

19. Entry and Egress Panel: Hinged to side jamb.20. Panel Pairing Configuration: See Drawings.

D. Fabrication: Extruded aluminum frame and panel profiles, corner connectors, hinges, sliding and folding hardware, locking hardware, handles, glass and glazing, and weather stripping.1. Factory pre-assembled. Ship with system components and installation instructions.2. Exposed work matched to produce continuity of line and design with joints.3. No raw edges visible at joints.

E. Materials:1. Panels: Single lite; standard.2. Panels: Horizontal mullions at specified heights from the bottom of the panel.3. Panels: Simulated divided lites in pattern as shown on Drawings.4. Panel Size (W x H): As indicated on Drawings.5. Rail Depth: 1-3/4 inch (45 mm).6. Top Rail and Stile Width: 2-1/8 inch (53 mm).7. Bottom Rail Width: 2-1/8 inch (53 mm)

a. Manufacturer's standard kickplate. Height (in/mm): ______.8. Frame: Matching top track and side jambs.9. Top Track Width: 2-1/2 inch (64 mm)10. Top Track and Side Jambs Depth: 1-3/4 inch (45 mm)11. Sill Type: Standard sill12. Sill Type: Low profile saddle sill13. Sill Type: Flush sill14. Sill Type: ADA compliant flush sill15. Sill Type: Surface mounted interior sill16. Sill Finish: Aluminum with a clear anodized finish.17. Sill Finish: Aluminum with a dark bronze anodized finish.18. Sill Finish: Aluminum with finished to match panel (only with standard sill).

08410 -6

19. For ADA Compliance at Swing Panel: Provide gasket to cover the channel in the sill at swing panels.

20. Aluminum Extrusions: AIMgSi0.5 alloy, 6063-T5; F-22 - European standard.a. Thickness: 0.078 inch (2.0 mm) nominal.b. Panel and Frame Finish: One color inside and outside.

1) Finish Type: Anodized per AAMA 611. Clear.2) Finish Type: Anodized per AAMA 611. Dark bronze.3) Finish Type: Powder coat per AAMA 2604.

a) Color: Chosen from standard selection of 50 colors. Matte.b) Color: Chosen from full RAL selection. High gloss.c) Color: Chosen from full RAL selection. Matte.

4) Finish Type: PVDF Coat per AAMA 2605: Fluoropolymer Kynar with color to match custom finish.

5) Finish Type: Custom finish.c. Panel and Frame Finish: Different color inside and outside.

1) Interior: Anodized per AAMA 611. Clear.2) Interior: Anodized per AAMA 611. Dark bronze.3) Interior: Powder coat per AAMA 2604.


4) Interior: PVDF Coat per AAMA 2605: Fluoropolymer Kynar with color to match custom finish.

5) Interior: Custom finish.6) Exterior: Anodized per AAMA 611. Clear.7) Exterior: Anodized per AAMA 611. Dark bronze.8) Exterior: Powder coat per AAMA 2604.


9) Exterior: PVDF Coat per AAMA 2605: Fluoropolymer Kynar with color to match custom finish.

10) Exterior: Custom finish.

F. Glass and Glazing:1. Safety Glazing per ASTM C1036, ASTM C1048, ANSI Z97.1 and CPSC 16CFR 1201.2. Manufacturer's Glass Lites: Dry glazed with glass stops on the inside.3. Glass Type: Tempered.4. Glass Type: Tempered and laminated.5. Glass Type: Laminated.6. Glass Type: Reduced iron; standard.7. Glass Type: Low iron.8. Glass Type: Solar bronze.9. Glass Type: Solar gray.10. Glass Type: Bird safe.11. Glass Lite; Single: 5/16 inch (8 mm) STC 37 enhanced laminated glass to achieve unit

STC of 35.12. Glass Lite; Single: 1/4 inch (6 mm) STC 36 enhanced laminated glass to achieve unit

STC of 34.13. Glass Lite; Single: 1/4 inch (6 mm) STC 35 laminated glass to achieve unit STC of 33.14. Glass Lite; Single: 1/4 inch (6 mm) STC 31 tempered glass to achieve unit STC of 30.15. Glass Lite; Double IGU: 13/16 inch (20 mm) thick.16. IGU Fill: Air filled17. IGU Fill: Argon filled.18. IGU Surface: Clear.19. IGU Surface: Low-E coating on No. 2 surface of double IGU.

08410 -7

20. IGU Surface: Low-E coating on No. 2 and No. 4 surface of double IGU.21. Glass Spacers: Manufacturer's standard.22. Glass Spacers: Gray finish with capillary tubes.23. Glass Spacers: Dark bronze finish with capillary tubes.24. Glass Spacers: Gray finish without capillary tubes.25. Glass Spacers: Dark bronze finish without capillary tubes.

G. Locking Hardware and Handles:1. Main Entry Panel or Pair of Panels for Models with a Swing Panel or Panels:

a. Lever Handles: On inside and outside.b. Lever Handles: With return on inside and outside.c. Standard lockset with lockable latch.d. Multi-point locking with concealed dead bolt and rods at top and bottom on

primary panel only.e. Operation: After turn of key or thumb-turn, depression of handles withdraws

latch. Lifting of handles engages rods and key or thumb turn engages deadbolt and operates lock.

f. Rods to be concealed and not edge mounted.g. Secondary Swing Panel: Two-point locking with flat handles on inside only for

secondary swing panel.h. Lever Handles Finish: Brushed satin stainless steel; standard.i. Lever Handles Finish: Titanium black stainless steel; standard.j. Lever Handles Finish: Copper- nickel stainless steel antiviral and antimicrobial.k. Lever Handles Finish: Oil rubbed bronze solid brass.l. Lever Handles Finish: Satin nickel solid brass.m. Lever Handles Finish: White solid brass.n. Locking: Standard profile cylindero. Locking: Adapter for Small Format Interchangeable Core.

2. Main Entry Panel for Models with a Swing Panel or a Pair of Swing Panels: Lever handles on inside and outside with single action, emergency egress, interconnected lock.

3. Main Entry Panel or Pair of Panels for Models with a Swing Panel or Swing Panels Attached to a Side Jamb: Manufacturer's push-pull handles with separate lockset and dead bolt.a. Push-pull handles Finish: Brushed stainless steel.

4. Main Entry Panel or Pair of Panels for Models with Swing or paired Swing Panels: Field installed panic devices per Section 08710.

5. Main Entry Panel or Pair of Panels for Inswing Models without Swing Panel or Panels: Manufacturer's L-shaped handle on inside, flat handle on outside and lock set with profile cylinder. Operation of lock set is by turn of key from the outside and with a thumb-turn from the inside with a two-point locking hardware operated by 180 degree turn of the handle.a. L-Shaped Handles: Stainless steel brushed satin finish.b. L-Shaped Handles: Stainless steel titanium black finish.c. L-shaped Handles : Copper-nickel stainless steel antiviral and antimicrobial.

6. Main Entry Panel or Pair of Panels for Outswing Models without Swing Panels: Flat handle on both sides and a lock set with a profile cylinder. Operation of lock set is by turn of key from the outside and from the inside with a two-point locking hardware operated by 180 degree turn of the handle.

7. Main Entry Panel or Pair of Panels for Models without Swing Panels: Flat handle on inside with concealed two-point locking hardware operated by 180 degree turn of handle.

8. Secondary Panels and Pairs of Folding Panels: Handles and concealed one or two-point locking hardware operated by 180 degree turn of handle between each pair. Face applied flush bolt locking not acceptable; except for units with paired panels.a. Handles: Manufacturer's flat handles.

08410 -8

1) Flat Handle Finish: Brushed satin stainless steel.2) Flat Handle Finish: Black titanium stainless steel.3) Flat Handle Finish: Copper-nickel stainless steel antiviral and

antimicrobial.4) Flat Handle Finish: Powder coated aluminum with color finish to match

frame.b. Handles: Removable custodial handles.

9. Handle Height: 41-3/8 inch (105 cm) centered from bottom of panel unless otherwise indicated on Drawings.

10. Locking Rods: End caps top and bottom;. Rod Stroke: 15/16 inch (24 mm).11. Additional Profile Cylinders: Keyed alike.12. Additional Profile Cylinders: Keyed differently.

H. Sliding and Folding Hardware:1. Manufacturer's combination sliding and folding hardware with top, bottom tracks.2. For Each Pair of Folding Panels: Independent cardanic suspension for 4 wheeled

rollers coated with fiberglass reinforced polyamide upper running carriage and lower guide carriage.

3. Swing Panel Hinges: Zinc die cast with finish closest match to finish of frame and panels and stainless-steel security hinge pins with set-screws.

4. Swing Panel Hinges: Stainless steel hinges and security hinge pins with set-screws.5. Hinge Adjustment: 1/16 inch (1.5 mm) in width per hinge. Adjustments to be made

without needing to removing panels from tracks.

I. Weather Stripping: Double layer EPDM between panels and EPDM gasket and Q-Lon gasket or brush seal between panel and frame or brush seals with a two-layer fiberglass reinforced polyamide fin attached at both inner and outer bottom edge of door panels, with a recessed sill or on frame, for sealing between panels and between panel and frame.

J. Fasteners: Stainless steel screws for connecting frame components.

K. Accessories: Sidelights, transoms, corner posts, or single or double doors as indicated.

2.3 THERMALLY BROKEN ALUMINUM-FRAMED FOLDING GLASS WALL SYSTEMS (SL60)

A. Basis of Design: Model SL60. Thermally broken aluminum-framed folding glass wall system, top hung floor track supported as manufactured by Nana Wall Systems, Incorporated. Manufacturer's standard frame and panel profiles, with head track, side jambs and panels with dimensions as shown on Drawings.1. System Components: Aluminum frame, threshold, panels, sliding-folding and locking

hardware, weather stripping, glass and glazing, and, accessories as required for a complete working installation.a. Insect Screen: Fully retractable non-pleated screen. Ultra-strong, UV resistant


Industries, Inc.

B. Performance Criteria: Lab tested.1. Standard Flush Sill - Inward and Outward Opening.

a. Air Infiltration and Exfiltration per ASTM E283:1) At static air pressure difference of 1.57 psf (75 Pa):

a) Infiltration: 0.10 cu ft per min per sq ft (0.5 L per sec per sq m).b) Exfiltration: 0.08 cu ft per min per sq ft (0.4 L per sec per sq m).

2) At 6.24 psf (300 Pa):a) Infiltration: 0.37 cfm per sq ft (1.9 L per sec per sq m).b) Exfiltration: 0.17 cfm per sq ft (0.9 L per sec per sq m).

b. Structural Loading per ASTM E330 Design Pressure:

08410 -9

1) Positive Inswing or Negative Outswing: 40 psf (1920 Pa).2) Negative Inswing or Positive Outswing: 45 psf (2160 Pa).

c. Swing Panel with Surface Mounted Hinges - Operation / Cycling Performance per AAMA 920: 500,000 cycles.

2. Low Profile Saddle Sill - Inward and Outward Opening.a. Air Infiltration and Exfiltration per ASTM E283:

1) At static air pressure difference of 1.57 psf (75 Pa):a) Infiltration: 0.10 cu ft per min per sq ft (0.5 L per sec per sq m).b) Exfiltration: 0.08 cu ft per min per sq ft (0.4 L per sec per sq m).

2) At 6.24 psf (300 Pa):a) Infiltration: 0.37 cfm per sq ft (1.9 L per sec per sq m).b) Exfiltration: 0.17 cfm per sq ft (0.9 L per sec per sq m).

b. Water Penetration per ASTM E331, ASTM E547: No uncontrolled water leakage at a static test pressure of 5.43 psf (260 Pa) with weeps by others.

c. Structural Loading per ASTM E330 Design Pressure:1) Positive Inswing or Negative Outswing: 40 psf (1920 Pa).2) Negative Inswing or Positive Outswing: 45 psf (2160 Pa).

d. Swing Panel with Surface Mounted Hinges - Operation / Cycling Performance per AAMA 920: 500,000 cycles.

3. Hybrid Sill - Inward Opening.a. Air Infiltration per ASTM E283:

1) At static air pressure difference of 1.57 psf (75 Pa): Infiltration: 0.05 cu ft per min per sq ft (0.09 L per sec per sq m).

2) At 6.24 psf (300 Pa): Infiltration: 0.13 cfm per sq ft (0.67 L per sec per sq m).

b. Water Penetration per ASTM E331, ASTM E547: No uncontrolled water leakage at a static test pressure of 7.5 psf (360 Pa). Not applicable for even-even configurations.


4. Hybrid Sill - Outward Opening.a. Air Infiltration per ASTM E283:

1) At static air pressure difference of 1.57 psf (75 Pa): Infiltration: 0.02 cu ft per min per sq ft (0.07 L per sec per sq m).

2) At 6.24 psf (300 Pa): Infiltration: 0.10 cfm per sq ft (0.51 L per sec per sq m).

b. Water Penetration per ASTM E331, ASTM E547: No uncontrolled water leakage at a static test pressure of 7.5 psf (360 Pa). Not applicable for even-even configurations.


5. Higher Weather Performance Raised Sill; Inward Opening.a. Air Infiltration per ASTM E283:

1) At static air pressure difference of 1.57 psf (75 Pa): 0.02 cfm per sq ft (0.10 L per sec per sq m) or (0.25 cu m per hour per m).

2) At 6.24 psf (300 Pa): 0.06 cfm per sq ft (0.31 L per sec per sq m).b. Water Penetration per ASTM E331 and ASTM E547: No uncontrolled water

entry at 7.5 psf (360 Pa). Not applicable for even-even configurations.c. Structural Loading per ASTM E330:

1) Design Pressure Positive: 45 psf (2160 Pa).2) Design Pressure Negative: 45 psf (2160 Pa).

6. Higher Weather Performance Raised Sill; Outward Opening.a. Air Infiltration per ASTM E283:

1) At static air pressure difference of 1.57 psf (75 Pa): 0.01 cfm per sq ft

08410 -10

(0.05 L per sec per sq m).2) At 6.24 psf (300 Pa): 0.01 cfm per sq ft (0.05 L per sec per sq m).

b. Water Penetration per ASTM E331 and ASTM E547: No uncontrolled water leakage at 7.5 psf (360 Pa).

c. Structural Loading per ASTM E330:1) Design Pressure Positive: 45 psf (2160 Pa).2) Design Pressure Negative: 40 psf (1920 Pa).

7. Glass Acoustical Performance per DIN 52210-3,4: With 38 Db glass, unit Rw (STC) of 36

8. System Life Cycle Performance per DIN EN 1191/12400: Pass; 20,000 cycles9. Forced Entry per AAMA 1304: Meets requirements10. Burglary Resistance: EN 1627-30, Class RC2/ RC2N; Resistance Class 2 certified.11. Lockset Burglary Resistance: PAS 24 certified.12. Florida Product Approval for Wind Loading: Units tested to AAMA/WDMA/CSA

101/I.S.2/A440 and approved according to the Florida Building Code 2014, Section 1710.5, for panel sizes subject to manufacturer size charts.a. Product Approval Number: FL24434. Approved for use outside hurricane zones

(HVHZ) with Design Pressure plus or minus 45 psf. for tested panel size.13. Thermal Performance U-factor: NFRC 100 rated, certified and labeled14. Solar Heat Gain Coefficient and Visible Light Transmission: NFRC 200 rated, certified

and labeled.15. Air Leakage: NFRC 400 rated, certified and labeled.16. Condensation Resistance Factor (CRF): NFRC 500 rated, certified and labeled.17. EPA Energy Star: Meets requirements with certain, specific glass.

C. Design Criteria:1. Sizes and Configurations: As indicated by the Drawings for selected number and size

of panels, location of swing panels, and stacking.2. Operation: Sliding and folding hardware with top and bottom tracks.3. Mounting Type: Top-hung.4. Mounting Type: Floor track supported.5. Panel Configuration: Straight.6. Panel Configuration: Window- Door Combination7. Panel Type: Hinged.

a. Primary swing panel of paired swing panels, looking from inside: On the left.b. Primary swing panel of paired swing panels, looking from inside: On the right.c. Entry and Egress panel hinged to side jamb.

8. Panel Pairing Configuration: See Drawings.9. Stack Storage Configuration: Inswing.10. Stack Storage Configuration: Outswing.

D. Fabrication: Extruded aluminum frame and panel profiles, corner connectors, hinges, sliding and folding hardware, locking hardware, handles, glass, glazing, and weather stripping.1. Factory pre-assembled. Ship with system components and installation instructions.2. Exposed work matched to produce continuity of line and design with joints.3. No raw edges visible at joints.

E. Materials:1. Panels: Single lite; standard.2. Panels: Horizontal mullions at specified heights from the bottom of the panel.3. Panels: Single lite with simulated divided lites in pattern as shown on Drawings.4. Panel Size (W x H): As indicated on Drawings.5. Rail Depth: 2-5/16 inch (59 mm).6. Top Rail and Stile Width: 2-3/8 inch (60 mm).7. Bottom Rail Width: 2-3/8 inches (60 mm).

a. Manufacturer's standard kickplate. Height (in/mm): ______.

08410 -11

8. Frame: Matching top track and side jambs.a. Top Track Width; Top-Hung: 3-15/16 inch (100 mm).b. Top Track Width; Floor Supported: 2-9/16 inch (65 mm).c. Side Jambs Width: 2-9/16 inch (65 mm).d. Top Track and Side Jambs Depth: 3-1/8 inch (66 mm).

9. Sill Type: Higher weather performance raised sill; thermally broken.10. Sill Type: Flush sill; thermally broken.11. Sill Type: Low profile saddle sill; thermally broken.12. Sill Type: Hybrid sill; thermally broken.13. Sill Type: Surface mounted interior sill; not thermally broken, only for floor supported

system.14. Sill Aluminum Finish: Clear anodized finish.15. Sill Aluminum Finish: Dark bronze anodized finish.16. Sill Aluminum Finish: Finished to match panel only with higher weather performance

sill.17. Aluminum Extrusions: AIMgSi0.5 alloy, 6063-T5; F-22 - European standard.

a. Thickness: 0.078 inch (2.0 mm) nominal.b. Thermal Break: 7/8 inch (22 mm) wide glass fiber reinforced polyamide.c. Panel and Frame Finish: One color inside and outside.



4) Finish Type: PVDF Coat (AAMA 2605): Fluoropolymer Kynar with color to match custom finish.

5) Finish Type: Custom finish.d. Panel and Frame Finish: Different color inside and outside.



4) Interior: PVDF Coat (AAMA 2605): Fluoropolymer Kynar with color to match custom finish.



9) Exterior: PVDF Coat (AAMA 2605): Fluoropolymer Kynar with color to match custom finish.


F. Glass and Glazing:1. Safety Glazing per ASTM C1036, ASTM C1048, ANSI Z97.1 and CPSC 16CFR 1201.2. Glazing Units, Double Insulated: Dry glazed with glass stops on the inside.

a. Glass Lites: Tempered.b. Glass Lites: Laminated.c. Glass Lites: Tempered and laminated.d. Thickness: 15/16 inch (24 mm) thick.

3. Glazing Units, Triple Insulated: Dry glazed with glass stops on the inside.

08410 -12

a. Glass Lites: Tempered.b. Glass Lites: Laminated.c. Glass Lites: Tempered and laminated.d. Thickness: 1-3/8 inch (35 mm) thick.

4. Insulated Glazing Unit Fill: Air.5. Insulated Glazing Unit Fill: Argon.6. Insulated Glazing Unit Fill: Krypton.7. Glass Type: Standard.8. Glass Type: Low iron.9. Glass Type: Solar bronze.10. Glass Type: Solar gray.11. Glass Type: Bird safe.12. Glass Spacers: Gray finish with capillary tube.13. Glass Spacers: Dark bronze finish with capillary tubes.14. Glass Spacers: Gray finish without capillary tubes.15. Glass Spacers: Dark bronze finish without capillary tubes.16. Insulated Glass Unit Surfaces: Clear.17. Insulated Glass Unit Surfaces: Low- E coating on No. 2 surface of double IGU.18. Insulated Glass Unit Surfaces: Low- E coating on No. 2 surface and No. 4 surface of

double IGU.19. Insulated Glass Unit Surfaces: Low-E coating on No. 2 surface and No. 5 surface of

triple IGU.

G. Locking Hardware and Handles:1. Main Entry Panels for Models with a Swing Panel or Pair of Swing Panels:




f. Rods to be concealed and not edge mounted.g. Secondary Swing Panel: Dummy lever handles; both sides. Concealed flush

bolts operate rods at top and bottom for secondary swing panel.h. Secondary Swing Panel: Two-point locking with flat handles on inside only for

secondary swing panel.i. Lever Handles Finish: Brushed satin stainless steel; standard.j. Lever Handles Finish: Titanium black stainless steel; standard.k. Lever Handles Finish: Copper- nickel stainless steel antiviral and antimicrobial.l. Lever Handles Finish: Oil rubbed bronze solid brass.m. Lever Handles Finish: Satin nickel solid brass.n. Lever Handles Finish: White solid brass.o. Locking: Standard profile cylinderp. Locking: Adapter for Small Format Interchangeable Core.

2. Main Entry Panels for Models with Swing Panels Attached to Side Jamb with Surface Mounted Hinges: Manufacturer's push-pull handles with separate lockset and dead bolt.a. Push-pull handles in a brushed stainless-steel finishb. Flat Handle Finish: Brushed satin stainless steel.c. Flat Handle Finish: Black titanium stainless steel.d. Flat Handle Finish: Copper-nickel stainless steel antiviral and antimicrobial.

3. Main Entry Panel: For models with single swing panel attached to side jamb and with surface mounted hinges. No hardware or locking provided by manufacturer; Field installed panic device per Section 08710.

08410 -13

4. Main Entry Panel: For models with paired swing panel attached to side jamb and with surface mounted hinges. No hardware or locking provided by manufacturer; Field installed panic device per Section 08710.

5. Main Entry Pair of Panels on Inswing Models without a Swing Panel: L-shaped handle on inside, flat handle on outside and lock set with profile cylinder.a. Operation of Lock Set: By turn of key from outside and with a thumb-turn from

inside with a two-point locking hardware operated by 180 degree turn of handle.b. L-Shaped Handles: Stainless steel brushed satin finish.c. L-Shaped Handles: Stainless steel titanium black finish.d. L-Shaped Handles: Copper-nickel stainless steel antiviral and antimicrobial.

6. Main Entry Panels for Outswing Models without Swing Panels: Flat handle on inside and a lock set with a profile cylinder on outside.a. Operation of Lock Set: By turn of key from the outside and from inside with a

two-point locking hardware operated by 180 degree turn of handle.7. Main Entry Panels for Models without Swing Panels: Flat handle on inside only with

concealed two-point locking hardware operated by 180 degree turn of handle.8. Secondary Panels and Pairs of Folding Panels: Handles and concealed one or two-

point locking hardware operated by 180 degree turn of handle between each pair. Face applied flush bolt locking not acceptable; except for units with paired panels.a. Handles: Manufacturer's flat handles.


antimicrobial.4) Flat Handle Finish: Powder coated aluminum with color finish to match

frame.b. Handles: Removable custodial handles.


10. Locking Rods: End caps top and bottom;. Rod Stroke: 15/16 inch (24 mm).11. Additional Profile Cylinders: Keyed alike.12. Additional Profile Cylinders: Keyed differently.

H. Sliding-Folding Hardware: Combination with top and bottom tracks and threshold. Running carriages with sealed, self-lubrication, ball bearing multi-rollers. Surface mounted hinges and running carriages not acceptable.1. Each Pair of Folding Panels:

a. Top-Hung: Independent cardanic suspension for 4 wheeled rollers coated with fiberglass reinforced polyamide upper running carriage and lower guide carriage. Running Carriage: Adjustable height, 1/4 inch (6 mm) up and down.

b. Floor Supported: Upper guide carriage and lower running carriage, two vertical stainless-steel wheels and two horizontal wheels. Vertical wheels to ride on stainless steel guide track covers over full length of sill track. Lie above water run-off level. Lower Running Carriage Carrying Capacity: 220 lbs. (100 kg)

2. Corner Connectors: On all four corners of panels. Thermally broken die cast zinc multi-functional corner fittings with carriage connectors and hinges.a. Hinge Pins: Standard.b. Hinge Pins: Removable.c. Finish: Powder coated, closest match to finish of frame and panel.d. Adjustment: 1/16 inch (1.5 mm) in width per hinge adjustments without

removing panels from tracks and without needing to remove panels from tracks.

I. Weather Stripping: Manufacturer's double layer EPDM between panels and EPDM gasket and Q-Lon gasket or brush seal between panel and frame or brush seals with two-layer polyamide fin attached to inner and outer edge of door panels with a recessed sill or on frame for sealing between panels and between panel and frame.

08410 -14

1. UniverSILL: For outswing low profile saddle sill, UniverSILL gasket add on available for additional air and water protection.

J. Fasteners: Tapered pins and stainless-steel screws for connecting frame components.


2.4 THERMALLY BROKEN ALUMINUM-FRAMED FOLDING GLASS WALL SYSTEMS (SL70)

A. Basis of Design: Model SL70. Monumental thermally broken aluminum-framed folding glass wall system, floor track supported as manufactured by Nana Wall Systems, Incorporated. Manufacturer's standard or post reinforced frame and panel profiles, with top track, side jambs and panels with dimensions as shown on Drawings.1. System Components: Aluminum frame, threshold, panels, sliding-folding and locking

hardware, weather stripping, glass and glazing, and accessories as required for a complete working installation.a. Insect Screen: Fully retractable non-pleated screen. Ultra-strong, UV resistant


Industries, Inc.

B. Performance Criteria:1. Standard Flush Sill; Inward Opening:

a. Air Infiltration per ASTM E283 Inward Opening:1) At static air pressure difference of 1.57 psf (75 Pa): 0.15 cfm per sq ft


b. Structural Loading per ASTM E330: Inward Opening.1) Wind load Resistance: Pass; C4.

a) Design Pressure Positive and Negative: 70 psf (3350 Pa).2. Standard Flush Sill; Outward Opening:

a. Air Infiltration per ASTM E283: Outward Opening:1) At static air pressure difference of 1.57 psf (75 Pa): 0.14 cfm per sq ft


b. Structural Loading per ASTM E330: Outward Opening.1) Wind load Resistance: Pass; C4.

a) Design Pressure Positive and Negative: 70 psf (3350 Pa).3. Performance Criteria (Lab Tested): Low Profile Saddle Sill - Inward Opening.

a. Air Infiltration per ASTM E283: Inward Opening:1) At static air pressure difference of 1.57 psf (75 Pa): 0.15 cfm per sq ft

(0.76 L per sec per sq m).a) Without Weeps at 6.24 psf (300 Pa): 0.29 cfm per sq ft (1.47 L per

sec per sq m).b. Water Penetration per ASTM E331 and ASTM E547: No uncontrolled water

leakage at a static (with weeps) test pressure of 5.25 psf (250 Pa).c. Structural Loading per ASTM E330:

1) Wind load Resistance: Pass; C4.a) Design Pressure Positive and Negative: 70 psf (3350 Pa).

4. Performance Criteria (Lab Tested): Low Profile Saddle Sill - Outward Opening.a. Air Infiltration per ASTM E283: Outward Opening:

1) At static air pressure difference of 1.57 psf (75 Pa): 0.14 cfm per sq ft (0.71 L per sec per sq m).a) Without Weeps at 6.24 psf (300 Pa): 0.30 cfm per sq ft (1.52 L per

sec per sq m).b. Water Penetration per ASTM E331 and ASTM E547: No uncontrolled water

leakage at a static (with weeps) test pressure of 6.00 psf (300 Pa).

08410 -15

c. Structural Loading per ASTM E330:1) Wind load Resistance: Pass; C4.

a) Design Pressure Positive and Negative: 70 psf (3350 Pa).5. Higher Weather Performance Raised Sill - Inward Opening.

a. Air Infiltration per ASTM E283:1) At static air pressure difference of 1.57 psf (75 Pa): 0.16 cfm per sq ft


b. Water Penetration per ASTM E331 and ASTM E547: No uncontrolled water leakage at a static test pressure of 9 psf (440 Pa).

c. Dynamic Water Penetration per AAMA 520 and ASTM E2268:1) Performance Level 2 at 6 to 18 psf (300 to 860 Pa).

d. Structural Load Deflection per TAS 202 and ASTM E330: DP-40 and DP-45.1) Wind load Resistance: Pass.

a) Design Pressure Positive: 70 psf (3350 Pa); C4.b) Design Pressure Negative: 100 psf (4785 Pa); C3.

6. Higher Weather Performance Raised Sill - Outward Opening.a. Air Infiltration per ASTM E283:

1) At static air pressure difference of 1.57 psf (75 Pa): 0.02 cfm per sq ft (0.10 L per sec per sq m).

2) At 6.24 psf (300 Pa): 0.08 cfm per sq ft (0.41 L per sec per sq m).b. Water Penetration per ASTM E331 and ASTM E547: No uncontrolled water

leakage at a static test pressure of 9 psf (440 Pa).c. Dynamic Water Penetration per AAMA 520 and ASTM E2268: Performance

Level 1 at 5 to 15 psf (250 to 715 Pa).d. Structural Load Deflection per TAS 202 and ASTM E330: DP-40 and DP-45.

1) Wind load Resistance: Pass.a) Design Pressure Positive and Negative: 70 psf (3350 Pa); C3.

7. Forced Entry per AAMA 1304 and ASTM F842: Meets requirements for plus F1.8. Swing Panel - Operation / Cycling Performance per AAMA 920: 500,000 cycles.9. System - Life Cycle Performance per DIN EN 1191 and 12400: 20,000 cycles.10. Florida Product Approval for Wind Loading: Units tested to AAMA/WDMA/CSA

101/I.S.2/A440 and approved according to the Florida Building Code 2014, Section 1710.5, for panel sizes subject to manufacturer size charts.a. Product Approval Number: FL23502. Standard Units with panel size up to 36

inches (914 mm) wide x 96 inches (2438 mm) high; subject to manufacturer size chart.

11. Acoustic Performance per DIN 52210-3,4: STC (Rw)a. System STC (Rw) 43 (43) and OITC 35 with 1-1/2 inch (38 mm) double IGU, 10

mm + 8 mm STC 48 laminated glassb. System STC (Rw) 41 (41) and OITC 33 with 1-7/16 inch (36 mm) double IGU, 8

mm laminated and 6 mm tempered STC 43 glassc. System STC (Rw) 33 (33) and OITC 27 with 15/16 inch (24 mm) double IGU, 4

mm and 4 mm STC 32 tempered glassd. System STC (Rw) 42 (42) with 1-5/16 inch (34 mm) double IGU, 6 mm + 6 mm

STC 44 enhanced laminated glass.e. System STC (Rw) 41 (41) with 1 inch (25 mm) double IGU, 6 mm + 6 mm STC

42 laminated glass.f. System STC (Rw) 38 (38) with 1/2 inch (12 mm) STC 39 enhanced laminated

glass.g. System STC (Rw) 37 (37) with 5/16 inch (8 mm) STC 37 enhanced laminated

glass.h. System STC (Rw) 36 (36) with 1/4 inch (6 mm) STC 36 enhanced laminated

glass.i. System STC (Rw) 35 (35) with 1/4 inch (6 mm) STC 35 laminated glass.j. System STC (Rw) 32 (32) with 1/4 inch (6 mm) STC 31 tempered glass.

08410 -16

12. Thermal Performance; U-Factor: NFRC 100 rated, certified, and labeled13. Solar Heat Gain Coefficient plus Visible Light Transmission: NFRC 200 rated,

certified, and labeled.14. Air Leakage: NFRC 400 rated, certified, and labeled.15. Condensation Resistance Factor: NFRC 500 rated, certified, and labeled.16. EPA Energy Star: Meets requirements with certain, specific glass.

C. Design Criteria:1. Sizes and Configurations: As indicated by the Drawings for selected number and size

of panels, location of swing panels, and location of tracks and stacking.2. Operation: Sliding and folding hardware with top and bottom tracks.3. Mounting Type: Floor track supported.4. Panel Configuration: Straight.5. Panel Configuration: Segmented curve.6. Panel Configuration: 90 degree angle turn.7. Panel Configuration: 135 degree angle turn.8. Panel Configuration: Window-Door combination9. Panel Type: Hinged.

a. Primary swing panel of paired swing panels, looking from inside: On the left.b. Primary swing panel of paired swing panels, looking from inside: On the right.c. Entry and Egress panel hinged to side jamb.

10. Panel Pairing Configuration: See Drawings.11. Stack Storage Configuration: Inswing.12. Stack Storage Configuration: Outswing.

D. Fabrication: Extruded aluminum frame and panel profiles, corner connectors, hinges, sliding and folding hardware, locking hardware, handles, glass, glazing, and sound gasketing.1. Factory pre-assembled. Ship with system components and installation instructions.2. Exposed work matched to produce continuity of line and design with joints.3. No raw edges visible at joints.

E. Materials:1. Panels: Single lite; standard.2. Panels: Multiple lites with horizontal mullions at specified heights from the bottom of

the panel.3. Panels: Single lite with simulated divided lites in pattern as shown on Drawings.4. Panel Size (W x H): As indicated on Drawings.5. Rail Depth: 2-3/4 inch (70 mm).6. Top Rail and Stile Width: 2-1/4 inch (57 mm)7. Bottom Rail Width: 2-1/4 inches (57 mm)

a. Manufacturer's standard kickplate. Height (in/mm): ______.8. Frame: Matching top track and side jambs.

a. Top Track and Side Jambs Width: 2-9/16 inch (65 mm).b. Top Track and Side Jambs Depth: 3-1/8 inch (80 mm).

9. Sill Type: Higher weather performance raised sill; thermally broken.10. Sill Type: Flush sill; thermally broken.11. Sill Type: Low profile saddle sill; thermally broken).12. Sill Type: Surface mounted interior sill; not thermally broken.13. Sill Aluminum Finish: Clear anodized finish.14. Sill Aluminum Finish: Dark bronze anodized finish.15. Sill Aluminum Finish: Finished to match panel only with higher weather performance

sill.16. For ADA Compliance: Provide gasket to cover the channel in the sill at swing doors.17. Aluminum Extrusions: AIMgSi0.5 alloy, 6063-T5; F-22 - European standard.

a. Thickness: 0.078 inch (2.0 mm) nominal.b. Thermal Break: 3/4 to 15/16 inch (20 to 24 mm)wide glass fiber reinforced

08410 -17

polyamide.c. Panel and Frame Finish: One color inside and outside.



4) Finish Type: PVDF Coat (AAMA 2605): Fluoropolymer Kynar with color to match custom finish.

5) Finish Type: Custom finish.d. Panel and Frame Finish: Different color inside and outside.



4) Interior: PVDF Coat (AAMA 2605): Fluoropolymer Kynar with color to match custom finish.



9) Exterior: PVDF Coat (AAMA 2605): Fluoropolymer Kynar with color to match custom finish.


F. Glass and Glazing:1. Safety Glazing per ASTM C1036, ASTM C1048, ANSI Z97.1 and CPSC 16CFR 1201.2. Glazing Units, Single Insulated: Dry glazed with glass stops on the inside.

a. Glass Lites: Laminated.b. Thickness: 1/2 inch (12 mm) STC 39 enhanced laminated glass to achieve unit

STC of 38.c. Thickness: 5/16 inch (8 mm) STC 37 enhanced laminated glass to achieve unit

STC of 37.d. Thickness: 1/4 inch (6 mm) STC 36 enhanced laminated glass to achieve unit

STC of 36.e. Thickness: 1/4 inch (6 mm) STC 35 laminated glass to achieve unit STC of 35.f. Thickness: 1/4 inch (6 mm) STC 31 tempered glass to achieve unit STC of 32.

3. Glazing Units, Double Insulated: Dry glazed with glass stops on the inside.a. Glass Lites: Laminated.b. Thickness: 1-5/16 inch (34 mm), 6 mm + 6 mm STC 44 enhanced laminated

glass to achieve unit STC of 42.c. Thickness: 1 inch (25 mm), 6 mm + 6 mm STC 42 laminated glass to achieve

unit STC of 41.4. Glazing Units, Triple Insulated: Dry glazed with glass stops on the inside.

a. Glass Lites: Tempered.b. Glass Lites: Laminated.c. Glass Lites: Tempered and laminated.d. Thickness: 1-1/2 inch (38 mm) thick.

5. Insulated Glazing Unit Fill: Air.6. Insulated Glazing Unit Fill: Argon.

08410 -18

7. Insulated Glazing Unit Fill: Krypton.8. Glass Type: Standard.9. Glass Type: Low iron.10. Glass Type: Solar bronze.11. Glass Type: Solar gray.12. Glass Type: Bird safe.13. Glass Type: Thermochronic dynamic.14. Glass Spacers: Gray finish with capillary tube.15. Glass Spacers: Dark bronze finish with capillary tubes.16. Glass Spacers: Gray finish without capillary tubes.17. Glass Spacers: Dark bronze finish without capillary tubes.18. Insulated Glass Unit Surfaces: Clear.19. Insulated Glass Unit Surfaces: Low-E coating on No. 2 surface of double IGU.20. Insulated Glass Unit Surfaces: Low-E coating on No. 2 surface and No. 4 surface of

double IGU.21. Insulated Glass Unit Surfaces: Low-E coating on No. 2 surface and No. 5 surface of

triple IGU.

G. Locking Hardware and Handles:1. Main Entry Panels for Models with a Swing Panel or Pair of Swing Panels:




f. Rods to be concealed and not edge mounted.g. Secondary Swing Panel: Matching dummy lever handles on both sides and

concealed flush bolts that operate the rods at the top and the bottom for the secondary swing panel.

h. Secondary Swing Panel: Two-point locking with U-shaped handles on inside only for the secondary swing panel.

i. Lever Handles Finish: Brushed satin stainless steel; standard.j. Lever Handles Finish: Titanium black stainless steel; standard.k. Lever Handles Finish: Copper- nickel stainless steel antiviral and antimicrobial.l. Lever Handles Finish: Oil rubbed bronze solid brass.m. Lever Handles Finish: Satin nickel solid brass.n. Lever Handles Finish: White solid brass.o. Locking: Standard profile cylinderp. Locking: Adapter for Small Format Interchangeable Core.

2. Main Entry Panels for Models with Swing Panels Attached to Side Jamb with Surface Mounted Hinges: Manufacturer's push-pull handles with separate lockset and dead bolt.a. Push-pull handles in a brushed stainless-steel finishb. Flat Handle Finish: Brushed satin stainless steel.c. Flat Handle Finish: Black titanium stainless steel.d. Flat Handle Finish: Copper-nickel stainless steel antiviral and antimicrobial.

3. Main Entry Panel for Models with Swing Panels and Pairs of Swing Panels: Lever handles on inside and outside with single action, emergency egress, interconnected lock.

4. Main Entry Panels for Models with a Swing Panel. Push-pull handles with separate lockset and dead bolt and one-point locking at top and bottom consisting of locking rods operated by a 180 degree turn of a flat handle on the inside.a. Push-pull handles in a brushed stainless-steel finish

08410 -19

b. Flat Handle Finish: Brushed satin stainless steel.c. Flat Handle Finish: Black titanium stainless steel.d. Flat Handle Finish: Copper-nickel stainless steel antiviral and antimicrobial.

5. Main Entry Panel for Models with Swing Panels or a Pair of Swing Panels: No hardware or locking provided by manufacturer; Field installed panic device per Section 08710.

6. Main Entry Pair of Panels Models without a Swing Panel: L-shaped handle on inside and outside, including a lock set with profile cylinder.a. Operation of Lock Set: By turn of key from outside and with a thumb-turn from

inside with a two-point locking hardware operated by 180 degree turn of handle.b. L-Shaped Handles: Stainless steel brushed satin finish.c. L-Shaped Handles: Stainless steel titanium black finish.d. L-shaped Handles: Stainless steel copper-nickel finish.

7. Main Entry Panel: U and L-shaped handle on inside only with concealed two-point locking hardware operated by 180 degree turn of handle.

8. Secondary Panels and Pairs of Folding Panels: Handles and concealed two-point locking hardware operated by 180 degree turn of handle between each pair.a. Handles: Manufacturer's standard.

1) Handle Finish: Brushed satin stainless steel.2) Handle Finish: Black titanium stainless steel.3) Handle Finish: Copper-nickel stainless steel antiviral and antimicrobial.4) Handle Finish: Brown nylon.5) Handle Finish: Gray nylon.6) Handle Finish: White nylon.

b. Handles: Removable custodial handles.9. Handle Height: 41-3/8 inch (105 cm) centered from bottom of panel unless otherwise

indicated on Drawings.10. Locking Rods: End caps top and bottom;. Rod Stroke: 15/16 inch (24 mm).11. Additional Profile Cylinders: Keyed alike.12. Additional Profile Cylinders: Keyed differently.

H. Sliding-Folding Hardware: Combination with top and bottom tracks and threshold. Running carriages with sealed, self-lubrication, ball bearing multi-rollers. Surface mounted hinges and running carriages not acceptable. Weight of panels borne by bottom of guide channel in sill is not acceptable.1. Lower Running Carriage Carrying Capacity: 440 lbs (200 kgs)2. Upper guide carriage and lower running carriage provided with four vertical stainless-

steel wheels and two horizontal polyamide wheels.3. Vertical wheels to ride on top of stainless-steel guide track covers over the full length

of the sill track and lie above the water run-off level.4. Wheels riding below water run-off level are not acceptable.5. Swing Panel Hinges:

a. Finish: Zinc die cast with finish closest match to finish of frame and panels and stainless-steel security hinge pins with set-screws standard.

b. Finish: Stainless-steel hinges and security hinge pins with set-screws.6. Adjustment: Folding-sliding hardware capable of compensation and adjustments

without needing to remove panels from tracks, in width, 1/16 inch (1.5 mm) per hinge and in height, 5/64 inch (2 mm) up and down.

I. Weather Stripping: Manufacturer's double layer EPDM between panels and EPDM gasket and Q-Lon gasket or brush seal between panel and frame or brush seals with two-layer polyamide fin attached to inner and outer edge of door panels with a recessed sill or on frame for sealing between panels and between panel and frame.1. UniverSILL: For outswing low profile saddle sill, UniverSILL gasket add on available

for additional air and water protection.

08410 -20

J. Fasteners: Tapered pins and stainless-steel screws for connecting frame components.


2.5 SLIDING-FOLDING THERMALLY-BROKEN ALUMINUM-FRAMED GLASS PANEL SYSTEMS

A. Basis of Design: Model SL84 sliding-folding thermally broken aluminum-framed glass panel system as manufactured by Nana Wall Systems, Incorporated. Nominal frame stile width of 3-7/8 inch (99 mm) between folding panels, floor track supported system. Manufacturer's standard thermally broken frame and panel profiles, with head track, side jambs, sill and panels with dimensions as shown on Drawings.1. System Components: Aluminum frame, threshold. panels, sliding-folding and locking

hardware, weather stripping, glass and glazing, panel catch, bionic turtle thermal break and accessories as required for a complete working installation.a. Insect Screen: Fully retractable non-pleated screen. Ultra-strong, UV resistant


Industries, Inc.

B. Performance Requirements: Lab tested.1. Sill and Opening Type: Hybrid Sill, Inward Opening:

a. Folding Glass Door Units tested to AAMA/WDMA/CSA 101/ I.S.2/ A440-17 (NAFS-17):1) SL84 Standard: Class CW-PG40 - FLD 4000 mm x 2600 mm with 1L3R

configuration and LC-PG50 - FLD 4000 mm x 2600 mm.2) SL84 Reinforced: Class CW-PG55 - FLD 4000 mm x 2600 mm with

1L3R configuration and LC-PG60 - FLD 4000 mm x 2600 mm.b. Air Infiltration per ASTM E283:

1) Static air pressure difference of 1.57 psf (75 Pa): 0.04 cfm per sq ft (0.20 L per sec per sq m)

2) Static air pressure difference of 6.24 psf (300 Pa): 0.11 cfm per sq ft (0.56 L per sec per sq m)

c. Water Penetration per ASTM E331 and ASTM E547: No uncontrolled water leakage at static test pressure of 9 psf (450 Pa). Not applicable for even-even configurations.

d. Structural Loading per ASTM E330: Wind load resistance.1) SL84 Standard:

a) Design Pressure; Positive: 50 psf (2400 Pa).b) Design Pressure; Negative: 55 psf (2670 Pa).

2) SL84 Reinforced:a) Design Pressure; Positive and Negative: 85 psf (2670 Pa).

2. Sill and Opening Type: Hybrid Sill, Outward Opening:a. Folding Glass Door Units test to AAMA/WDMA/CSA 101/I.S.2/ A440-17 (NAFS-

17):1) SL84 Standard: Class CW-PG40-FLD 4000 mm x 2600 mm with 1L3R

configuration and LC-PG55-FLD 4000 mm x 2600 mm.2) SL84 Reinforced: Class CW-PG55-FLD 4000 mm x 2600 mm with 1L3R

configuration and LC-PG60-FLD 4000 mm x 2600 mm.b. Air Infiltration per ASTM E283:

1) Static air pressure difference of 1.57 psf (75 Pa): 0.04 cfm per sq ft (0.20 L per sec per sq m).


c. Water Penetration per ASTM E331 and ASTM E547: No uncontrolled water leakage at a static test pressure of 9 psf (450 Pa). Not applicable for even-even configurations.

08410 -21


a) Design Pressure; Positive: 55 psf (2670 Pa)b) Design Pressure; Negative: 50 psf (2400 Pa)

2) SL84 Reinforced:a) Design Pressure; Positive and Negative: 85 psf (4050 Pa).

3. Sill and Opening Type: Low Profile Saddle Sill, Inward and Outward Opening:a. Folding Glass Door Units test to AAMA/WDMA/CSA 101/I.S.2/A440-17 (NAFS-


configuration.2) SL84 Reinforced: Class CW-PG35-FLD 4000 mm x 2600 mm with 1L3R

configuration.b. Air Infiltration per ASTM E283:



c. Water Penetration per ASTM E331 and ASTM E547: No uncontrolled water leakage at a static, with weeps, test pressure of 5.43 psf (260 Pa). Not applicable for even-even configurations.


a) Design Pressure; Positive and Negative: 50 psf (2400 Pa).2) SL84 Reinforced:

a) Design Pressure; Positive and Negative: 85 psf (4050 Pa)4. Sill and Opening Type: Low Profile Saddle Sill with UniverSILL Insert, Outward

Opening:a. Folding Glass Door Units test to AAMA/WDMA/CSA 101/I.S.2/ A440-17 (NAFS-


configuration and LC-PG55-FLD 4000 mm x 2600 mm.2) SL84 Reinforced: Class CW-PG55-FLD 4000 mm x 2600 mm with 1L3R

configuration and LC-PG60-FLD 4000 mm x 2600 mm.b. Air Infiltration per ASTM E283:



c. Water Penetration per ASTM E331 and ASTM E547: No uncontrolled water leakage at a static test pressure of 9 psf (450 Pa). Not applicable for even-even configurations.



a) Design Pressure; Positive and Negative: 85 psf (4050 Pa).5. Sill and Opening Type: Flush Sill, Inward and Outward Opening:

a. Structural Loading per ASTM E330: Wind load resistance.1) SL84 Standard:


a) Design Pressure; Positive and Negative: 85 psf (4050 Pa)b. Air Infiltration per ASTM E283:


08410 -22


6. Operation / Cycling Performance (AAMA 920): 500,000 cycles.7. Cycle Testing Performance per EN 1191: Class 3; 20,000 cycles.8. Forced Entry Resistance per ASTM F842, AAMA 1304, CAWM 300: Meets Grade 40;

plus F2.9. Burglary Resistance Unit: EN 1627-30, Class RC2/ RC2N; Resistance Class 2

certified.10. Burglary Resistance Lockset: PAS 24 certified.11. Thermal Performance (U-factor): NFRC 100 rated, certified, and labeled.12. Solar Heat Gain Coefficient plus Visible Light Transmission: NFRC 200 rated,

certified, and labeled.13. Air Leakage: NFRC 400 rated, certified, and labeled.14. Condensation Resistance Factor: NFRC 500 rated, certified, and labeled.

C. Design Criteria:1. Sizes and Configurations: As indicated on Drawings for selected number and size of

panels, location of swing panels, and number of panels stacking to the left and to the right.

2. Operation: Adjustable sliding and folding hardware with top and bottom tracks.3. Panel Configuration: Straight.4. Panel Configuration: 90 degree angle turn.5. Panel Configuration: Window and door combination6. Stack Storage Configuration: Inswing type.7. Stack Storage Configuration: Outswing type.8. Mounting Type: Floor track supported with upper guide track.9. Hinged Panels:

a. Primary Swing Panel of Paired Swing Panels Looking from Inside: On the left.b. Primary Swing Panel of Paired Swing Panels Looking from Inside: On the right.c. Entry and Egress Panel: Hinged to bi-folding panels.d. Entry and Egress Panel: Hinged to side jamb.e. Entry and Egress Panel: No.

10. Panel Pairing Configuration: Bi-folding panels hinged to side jamb.11. Panel Pairing Configuration: Bi-folding panels unhinged FourFold or SixFold panel

sets for SL84 Standard.12. Panel Pairing Configuration: Bi-folding panels unhinged FourFold or SixFold panel set

for SL84 Reinforced.

D. Fabrication: Extruded aluminum frame and panel profiles, corner connectors, hinges, sliding and folding hardware, locking hardware, handles, glass and glazing, and weather stripping.1. Factory pre-assembled. Ship with system components and installation instructions.2. Exposed work matched to produce continuity of line and design with joints.3. No raw edges visible at joints.

E. Materials:1. Panels: Single lite; standard.2. Panels: Multiple lites with horizontal mullions at heights indicated on Drawings from

bottom of panel.3. Panels: Single lite with simulated divided lites in pattern as shown on Drawings.4. Panel Size (W x H): As indicated on Drawings.5. Rail Depth: 3-1/8 inch (84 mm).6. Top Rail Width: 2-5/8 inch (66 mm).7. Typical Stile Width: 1-3/4 inch (45 mm) on both stile or a nominal frame stile width of

3-7/8 inch (99 mm) for standard.8. Typical Stile Width: 1-3/4 inch (45 mm) and 3-1/8 inch (79 mm) on two stile for a

nominal stile width of 5-1/4 inch (133 mm) for reinforced.

08410 -23

9. Bottom Rail Width: 2-5/8 inch (67 mm).10. Bottom Rail Width: Manufacturer's standard kick-plate of 10 inches (254 mm).11. Frame: Thermally broken top track and side jambs with multi-purpose frame insert to

hide anchoring connections.12. Frame: Thermally broken top track and side jambs without multi-purpose frame insert

to hide anchoring connections.13. Frame Finish: To match panel finish.14. Frame Depth: Top Track and Side Jamb Depth; 3-9/16 inch (91 mm).15. Head Track Width: 2-13/16 inch (72 mm) standard.16. Head Track Width: 3-7/8 inch (99 mm) with anti-tilt feature for unhinged SixFold panel

set configurations.17. Side Jambs: 2-13/16 inch (72 mm) wide. Adjustment: Plus or minus 3/16 inch (5 mm).18. Sill Type: Higher weather performance hybrid sill, thermally broken, with high heel

protector insert.19. Sill Type: ADA compliant Low-profile saddle sill, thermally broken, with high heel

protector insert.20. Sill Type: ADA compliant Low-profile saddle sill, thermally broken, with high heel

protector insert and with UniverSILL EPDM insert.21. Sill Type: ADA compliant Flush sill (thermally broken) with high heel protector insert.22. Sill Type: Surface Mounted Minimal ADA sill for interior application.23. Sill Finish: Aluminum with clear anodized finish.24. Sill Finish: Aluminum with black anodized finish.25. Aluminum Extrusions: AIMgSi0.5 alloy, 6063-T5; F-22 - European standard.

a. Thickness: 0.078 inch (2.0 mm) nominal.b. Thermal Break: 1-15/16 inches (49 mm) wide specially designed and patented

glass fiber reinforced (GFR) polyamide "Bionic Turtle.c. Finish: One color inside and outside.



4) Finish Type: Custom finish.d. Finish: Different color inside and outside.






F. Glass and Glazing:1. Safety Glazing per ASTM C1036, ASTM C1048, ANSI Z97.1 and CPSC 16CFR 1201.2. Glazing Units, Double Insulated: Dry glazed with glass stops on the inside.

a. Glass Lites: Tempered.b. Glass Lites: Laminated.c. Glass Lites: Tempered and laminated.

08410 -24

d. Thickness: 1-5/8 inch (42 mm), 10 mm + 8 mm STC 49 laminated glass to achieve unit STC of 44.

e. Thickness: 1-9/16 inch (40 mm), 8 mm + 8 mm STC 47 laminated glass to achieve unit STC of 43.

f. Thickness: 1-5/16 inch (34 mm), 8 mm laminated + 6 mm tempered STC 43 glass to achieve unit STC of 42.

g. Thickness: 1-1/4 inch (32 mm), 6 mm + 6 mm STC 42 laminated glass to achieve unit STC of 41.

h. Thickness: 1-1/4 inch (32 mm), 6 mm + 6 mm or 15/16 inch (24 mm) 4 mm + 4 mm tempered glass depending on panel height.

3. Glazing Units, Triple Insulated: Dry glazed with glass stops on the inside.a. Glass Lites: Tempered.b. Thickness: 1-9/16 inch (40 mm), 6 mm + 4 mm + 6 mm or 1-1/2 inch (36 mm) 4

mm + 4 mm + 4 mm tempered glass depending on panel height.4. Insulated Glazing Unit Fill: Air.5. Insulated Glazing Unit Fill: Argon.6. Insulated Glazing Unit Fill: Krypton.7. Glass Type: Standard. Reduced iron.8. Glass Type: Low iron.9. Glass Type: Solar bronze.10. Glass Type: Solar gray.11. Glass Type: Bird safe.12. Glass Spacers: Gray finish with capillary tube.13. Glass Spacers: Dark bronze finish with capillary tubes.14. Glass Spacers: Gray finish without capillary tubes.15. Glass Spacers: Dark bronze finish without capillary tubes.16. Insulated Glass Unit Surfaces: Clear.17. Insulated Glass Unit Surfaces: Low- E coating on No. 2 surface of double IGU.18. Insulated Glass Unit Surfaces: Low-E coating on No. 2 and No. 4 surface of double

IGU.19. Insulated Glass Unit Surfaces: Low-E coating on No. 2 and No. 5 surface of triple

IGU.20. Alarmed Glazing: Connection wiring to alarm system, position monitoring, locking

detection and notification systems such as glass-breakage sensors by others.

G. Locking Hardware and Handles:1. Main Entry Panels: Lockset with lockable latch, multi-point locking with dead bolt and

rods at top and bottom on primary panel only.a. Application: Single swing panel.b. Application: Pair of swing panels.c. Operation: After turn of key or thumb turn, depression of handles withdraws

latch. Lifting of handles engages rods and turn of key or thumb turn engages deadbolt and operates lock.

d. Rods: Concealed, not edge mounted.e. Lever Handles: Lever handles on inside and outside.f. Lever Handles: Lever handles with return on inside and outside.g. Lever Handle Finish: Brushed satin stainless steel; standard.h. Lever Handle Finish: Black titanium stainless steel; standard.i. Lever Handle Finish: Copper-nickel stainless steel antiviral and antimicrobial.j. Lever Handle Finish: Oil rubbed bronze solid brass.k. Lever Handle Finish: Satin nickel solid brass.l. Lever Handle Finish: White solid brass.m. Locking: Standard profile cylinder.n. Locking: Adaptor for Small Format Interchangeable Core.o. Secondary Swing Panel: Concealed two-point, edge locking.

2. Main Entry Panels: Lockset with lockable latch, single point locking with a deadbolt on

08410 -25

primary panel only.a. Application: Single swing panel.b. Application: Pair of swing panels.c. Locking: 5 pin US rim cylinder.d. Locking: US mortise cylinder accommodating 5 pin, SFIC, FSIC or LFIC cores.e. Lever Handles: Accurate 18L on inside and outside.f. Lever Handles: Accurate 20L with return on inside and outside.g. Lever Handle Finish: US32 satin stainless steel.h. Lever Handle Finish: US10B oil rubbed bronze.i. Secondary Swing Panel: Concealed two-point, edge locking.

3. Main Entry Panel: Flat handle on inside only with concealed two-point locking hardware operated by 180 degree turn of handle; the main entry panel is operable from inside only and there is no latch.

4. Main Entry Panel: No hardware or locking provided by manufacturer; Field installed panic device from Section 08710.a. Application: Single swing panel.b. Application: Pair of swing panels.

5. Secondary Panels and Pairs of Folding Panels: Handles and concealed two-point locking hardware operated by 180 degree turn of handle between each pair.a. Handles: Manufacturer's flat handles.


antimicrobial.b. Handles: Removable custodial handles.


7. Locking Rods: End caps top and bottom;. Rod Stroke: 15/16 inch (24 mm).8. Additional Profile Cylinders: Keyed alike.9. Additional Profile Cylinders: Keyed differently.10. Burglary Resistance: Standard.11. Burglary Resistance: Class RC2/ RC2N (Resistance Class 2) certified12. Panel catch: panel catch to hold swing panel to adjacent folding panel to prevent

incorrect operation when moving the panel.

H. Sliding-Folding Hardware: Combination with top and bottom tracks and threshold.1. Running carriages to have sealed, self-lubricating, double ball bearing multi-rollers.2. Surface mounted hinges and running carriages not acceptable.3. Weight of panels borne by the bottom of the guide channel in the sill not acceptable.4. Lower Running Carriage Carrying Capacity: 240 lb. (110 kg); lower running carriage

provided with two vertical stainless-steel wheels with double ball bearings and two horizontal polyamide wheels.

5. Vertical wheels with Gothic arch feature to ride on top of stainless-steel guide track covers over full length of sill track. Wheels on aluminum surfaces not acceptable.

6. Upper guide carriage with two horizontal polyamide guiding wheels. For configurations with pairs of panels that slide left or right, additional concealed, additional vertical tilt protection hardware.

7. Hinges: Anodized aluminum with stainless steel security hinge pins and set-screws. Additional patented (Patent No. US10711510B2) TwinX reinforcements between panels for a tight seal.a. Finish: Clear.b. Finish: Black.c. Roller Finish: Clear.d. Roller Finish: Black.

I. Weather Stripping: Double layer EPDM between panels and EPDM gasket, Q-Ion gasket, or

08410 -26

brush seal between panel and frame, or brush seals with a two-layer fiberglass reinforced polyamide fin attached at both inner and outer edge of bottom of door panels with a recessed sill or on frame for sealing between panels and between panel and frame1. UniverSILL: For outswing low profile saddle sill, UniverSILL gasket add on available

for additional air and water protection.

J. Fasteners: Tapered pins or stainless-steel screws for connecting frame components.

2.6 SLIDING-FOLDING THERMALLY BROKEN, ACOUSTICALLY RATED, ALUMINUM-FRAMED GLASS PANEL SYSTEM

A. Basis of Design: Model SL64 Acoustical sliding-folding thermally broken, acoustically rated, aluminum-framed glass panel system as manufactured by Nana Wall Systems, Incorporated. Nominal frame stile width of 3-7/8 inch (99 mm) between folding panels, floor track supported system; manufacturer's standard thermally broken frame and panel profiles, with head track, side jambs, sill and panels with dimensions as shown on Drawings.1. System Components: Aluminum frame, threshold, panels, sliding-folding and locking

hardware. sound gasketing, bionic turtle thermal break, glass and glazing, and accessories as required for a complete working installation.

B. Performance Requirements:1. Acoustic Performance:

a. STC (Rw) 45 (45) and OITC 37 with head track recessed and 1-7/16 inch (36 mm) double IGU, 12 mm + 8 mm STC 48 laminated glass.

b. STC (Rw) 38 (38) and OITC 32 with 1-1/8 inch (28 mm) double IGU, 6 mm laminated and 6 mm tempered STC 39 glass.

c. STC (Rw) 33 (33) and OITC 27 with 15/16 inch (24 mm) double IGU, 4 mm and 4 mm STC 31 tempered glass.

d. STC (Rw) 45 (45) with head track recessed and 1-9/16 inch (40 mm) double IGU, 10 mm + 8 mm STC 48 laminated glass.

e. STC (Rw) 44 (44) with head track recessed and 1-5/8 inch (42 mm) double IGU, 8 mm + 8 mm STC 47 enhanced laminated glass.

f. STC (Rw) 40 (40) with 1-7/16 inch (36 mm) double IGU, 6 mm + 6 mm STC 42 laminated glass.

g. STC (Rw) 38 (38) with 1/2 inch (12 mm) STC 39 laminated glass.h. STC (Rw) 37 (37) with 3/8 inch (10 mm) STC 38 laminated glass.i. STC (Rw) 36 (36) with 5/16 inch (8 mm) STC 36 laminated glass.j. STC (Rw) 35 (35) with 1/4 inch (6 mm) STC 35 laminated glass.

C. Design Criteria:1. Sizes and Configurations: As indicated by Drawings for selected number and size of

panels, location of swing and folding panels.2. Operation: Sliding and folding hardware with top and bottom tracks.3. Panel Swing: Inswing type and stack storage inside jamb.4. Panel Swing: Outswing type and stack storage outside jamb.5. Panel Configuration: Straight.6. Panel Mounting Type: Floor track supported with upper guide track.7. Panel Type: Hinged, with entry and egress panel hinged to side jamb.8. Panel Type: Hinged, without entry and egress panel hinged to side jamb.9. Panel Pairing Configuration: Bi-folding panels hinged to side jamb.10. Panel Pairing Configuration: Bi-folding panels unhinged FourFold panel sets.11. Panel Pairing Configuration: Bi-folding panels unhinged SixFold panel sets.12. Sill Type: Surface mounted minimal ADA sill.

D. Fabrication: Extruded aluminum frame and panel profiles, corner connectors, hinges, sliding and folding hardware, locking hardware, handles, glass, glazing, and sound gasketing.1. Factory pre-assembled. Ship with system components and installation instructions.

08410 -27

2. Exposed work matched to produce continuity of line and design with joints.3. No raw edges visible at joints.

E. Materials:1. Panels: Single lite.2. Panels: Multiple lites with horizontal mullions at heights indicated on Drawings from

the bottom of the panel.3. Panels: Single lite with simulated divided lites in pattern as shown on Drawings.4. Panel Size (W x H): As indicated on Drawings.5. Rail Depth: 2-5/8 inches (67 mm).6. Top Rail and Stile Width: 2-7/8 inches (73 mm).7. Bottom Rail Width: 2-5/8 inches (66 mm).8. Bottom Rail Width: Manufacturer's standard kick-plate of 10 inches (254 mm).9. Frame: Thermally broken top track and side jambs with multi-purpose frame insert to

hide anchoring connections.10. Frame Finish: To match panel finish.11. Frame Depth: 2-15/16 inch (74 mm).12. Head Track Width: 2-13/16 inch (72 mm) standard.13. Head Track Width: 3-7/8 inch (99 mm) for unhinged FourFold panel set

configurations.14. Head Track Width: 3-7/8 inch (99 mm) for unhinged SixFold panel set configurations.15. Side Jamb: 2 inches (51 mm) wide. Adjustment: Plus or minus 3/16 inch (5 mm).16. Sill Type: Surface Mounted Minimal ADA Sill with aluminum finish:17. Sill Finish: Clear anodized finish.18. Sill Finish: Black anodized finish.19. Aluminum Extrusions: AIMgSi0.5 alloy, 6063-T5; F-22 - European standard.

a. Thickness: 0.078 inch (2.0 mm) nominal.b. Acoustic Break: 1-1/4 inches (32 mm) wide specially designed glass fiber

reinforced (GFR) polyamide "Bionic Turtle".c. Finish: One-color inside and outside.

1) Finish Type: Anodized per AAMA 611. Clear.2) Finish Type: Anodized per AAMA 611. Dark bronze.3) Finish Type: Anodized per AAMA 611. Black.4) Finish Type: Powder coat per AAMA 2604.


5) Finish Type: Custom finish.d. Finish: Different color inside and outside.

1) Interior: Anodized per AAMA 611. Clear.2) Interior: Anodized per AAMA 611. Dark bronze.3) Interior: Anodized per AAMA 611. Black.4) Interior: Powder coat per AAMA 2604.


5) Interior: Custom finish.6) Exterior: Anodized per AAMA 611. Clear.7) Exterior: Anodized per AAMA 611. Dark bronze.8) Exterior: Anodized per AAMA 611. Black.9) Exterior: Powder coat per AAMA 2604.


10) Exterior: Custom finish

08410 -28

F. Glass and Glazing:1. Safety Glazing per ASTM C1036, ASTM C1048, ANSI Z97.1 and CPSC 16CFR 1201.2. Glass Lites: Dry glazed with glass stops on inside.

a. Single Glass:1) 1/2 inch (12 mm) STC 39 laminated to achieve unit STC of 38.2) 3/8 inch (10 mm) STC 38 laminated to achieve unit STC of 37.3) 5/16 inch (8 mm) STC 36 laminated to achieve unit STC of 36.4) 1/4 inch (6 mm) STC 35 laminated to achieve unit STC of 35.

b. Insulated Glass Units:1) 1-9/16 inch (40 mm) double IGU, 10 mm + 8 mm STC 48 laminated

glass to achieve unit STC of 45 with head track recessed.2) 1-5/8 inch (42 mm) double IGU, 8 mm + 8 mm STC 47 enhanced

laminated glass to achieve unit STC of 44 with head track recessed.3) 1-7/16 inch (36 mm) double IGU, 6 mm + 6 mm STC 42 laminated glass

to achieve unit STC of 40.c. Glass Spacers: Manufacturer's standard gray finish.d. Glass Spacers: Manufacturer's standard black finish.

3. Glass Lite Type: Reduced iron; standard.4. Glass Lite Type: Low iron.

G. Locking Hardware and Handles:1. Main Entry Panels: For applications with a swing panel, lockset with lockable latch,

multi-point locking with dead bolt, and rods at top and bottom on primary panel only.a. Operation: After turn of key or thumb turn, depression of handles withdraws

latch. Lifting handles engages rods and turn of key or thumb turn engages deadbolt and operates lock.

b. Rods: Concealed, not edge mounted.c. Lever Handles: Lever handles on inside and outside.d. Lever Handles: Lever handles with return on inside and outside.e. Lever Handle Finish: Brushed satin stainless steel; standard.f. Lever Handle Finish: Black titanium stainless steel; standard.g. Lever Handle Finish: Copper-nickel stainless steel antiviral and antimicrobialh. Lever Handle Finish: Oil rubbed bronze solid brass.i. Lever Handle Finish: Satin nickel solid brass.j. Lever Handle Finish: White solid brass.k. Locking: Standard profile cylinder;l. Locking: Adaptor for Small Format Interchangeable Core (SFIC).

2. Main Entry Panels: For applications with a swing panel; lockset with lockable latch, single point locking with a deadbolt on primary panel only.a. Locking: 5 pin US rim cylinder.b. Locking: US mortise cylinder accommodating 5 pin, SFIC, FSIC or LFIC cores.c. Lever Handles: Accurate 18L lever handles on inside and outside.d. Lever Handles: Accurate 20L lever handles with return on inside and outside.e. Lever Handle Finish: US32 satin stainless steel.f. Lever Handle Finish: US10B oil rubbed bronze.

3. Main Entry Panels: Flat handle on inside only with concealed two-point locking hardware operated by 180 degree turn of handle; the main entry panel is operable from inside only and there is no latch.

4. Main Entry Panels: For applications with a swing panel, no hardware or locking provided by manufacturer; field installed panic device as per Section 08710.

5. Pairs of Folding Panels: Concealed two-point locking hardware operated by 180 degree turn of handle between each pair. Face applied Surface Mounted Minimal bolt locking not acceptable.a. Handles: Flat handles.

1) Flat Handle Finish: Brushed satin stainless steel.2) Flat Handle Finish: Black titanium stainless steel.

08410 -29

3) Flat Handle Finish: Copper-nickel stainless steel antiviral and antimicrobial.

b. Handles: Removable custodial handles.6. Handle Height: 41-3/8 inch (105 cm) centered from bottom of panel unless otherwise

indicated on Drawings.7. Locking Rods: End caps top and bottom;. Rod Stroke: 15/16 inch (24 mm).8. Burglary Resistance: Standard.9. Burglary Resistance: Class RC2/RC2N certified.10. Additional Profile Cylinders: Keyed alike.11. Additional Profile Cylinders: Keyed differently.12. Panel catch: Panel catch to hold swing panel to adjacent folding panel to prevent

incorrect operation hen moving the panel.

H. Sliding-Folding Hardware: Combination with top and bottom tracks and threshold.1. Running carriages with sealed, self-lubricating, double ball bearing multi-rollers.2. Surface mounted hinges and running carriages not acceptable.3. Weight of panels borne by bottom of guide channel in the sill is not acceptable.4. Lower Running Carriage Carrying Capacity: 250 lb (120 kg); lower running carriage

provided with two vertical stainless-steel wheels and two horizontal polyamide wheels.5. Vertical wheels with Gothic arch feature to ride on top of stainless-steel guide track

covers over full length of sill track. Wheels riding on aluminum surfaces not acceptable.

6. Upper Guide Carriage: With two horizontal polyamide guiding wheels; additional concealed, additional vertical tilt protection hardware for configurations with pairs of panels that can slide left or right.

7. Hinges: Anodized aluminum with stainless steel security hinge pins and set-screws. Additional butterfly guides between panels for a tight seal.a. Finish: Clear.b. Finish: Dark bronze.c. Roller Finish: Clear.d. Roller Finish: Black.

I. Sound Gasketing: Double layer EPDM between panels. EPDM gasket, Q-Ion gasket, or brush seal between panel and frame. Brush seals with two-layer fiberglass reinforced polyamide fin attached at both inner and outer edge of bottom of door panels with a recessed sill or on frame for sealing between panels and between panel and frame.

J. Fasteners: Tapered pins or stainless-steel screws for connecting frame components.


PART 3 EXECUTION

3.1 EXAMINATION AND PREPARATION

A. Examine surfaces of openings and verify dimensions. Verify openings are level, plumb, and square, with no unevenness, bowing, or bumps on floor.1. Because of large dimensions involved and weight and movement of panels, verify

structural integrity of header; maximum deflection with both live and dead loads to be the lesser of L/720 of span or 1/4 inches (6 mm).

2. Structural support for lateral loads, wind load, and eccentric load when panels are stacked open.

B. Prepare openings using methods recommended by manufacturer for achieving the best result for the substrate under the project conditions.1. If preparation is the responsibility of another installer, notify Architect in writing of

deviations from manufacturer's recommended installation tolerances and conditions.

08410 -30

C. Do not proceed with installation until substrates are prepared using methods recommended by manufacturer and deviations from manufacturer's recommended tolerances are corrected. Commencement of installation constitutes acceptance of conditions.

3.2 INSTALLATION

A. Install per Drawings, submittals, and manufacturer's installation instructions.1. Properly flash, seal and waterproof around perimeter of opening.2. Attach anchorage devices in place, level, straight, plumb and square. Install frame in

proper elevation, plane and location, and in proper alignment with other work.3. When lower track is designed to drain, provide connections to allow for drainage.4. Install panels, handles, lockset, screens and other accessories in accordance with

manufacturer's recommendations and instructions.

B. Finishing: Field finish under Division 9; seal and finish promptly after installation and prior to exposure to weather in accordance with manufacturer recommendations.

C. Insect Screens: Install per manufacturer's recommendations and installation instructions.

3.3 FIELD QUALITY CONTROL

A. Field Inspection: Coordinate in accordance with appropriate sections in Division 01.

B. Verify system operates and functions properly. Adjust hardware for proper operation.

C. Non-Conforming Work: Repair or replace non-conforming work as directed by the Architect; see General and Supplementary Conditions, and Division 01, General Requirements.

D. Manufacturer's Services: Coordinate manufacturer's services in accordance with appropriate sections in Division 01.

3.4 CLEANING AND PROTECTION

A. Protect installed products until completion of project. Keep units closed and protect installation against damage from construction activities.

B. Remove protective coatings. Use manufacturer recommended methods to clean surfaces.

END OF SECTION

08410 -31

arcat · web viewsection 08410. folding glazed wall systems - exterior and interior. display hidden...

Documents