®

AQUACHECKTM

ASPHALT PRODUCTS - SPECIALTY PRODUCTS

AQUACHECKTM

SPECIALTY PRODUCTS

IBP - INTERNATIONAL BUILDING PRODUCTS, LLC.2711 N. Main Street • East Peoria Illinois 61611 • USAwww.IBPCONNECT.com

LN-1 MINERAL SPIRITS & GENERAL CLEANER

PRODUCT DESCRIPTION:

LN-1 Asphalt Products high quality mineral spirit is a a multi-purpose cleaner and thinner.

BASIC USES: LN-1 Mineral Spirits can be used as a thinner with paints, enamels, and varnishes. It is used as a clean-up solvent for brushes, rollers, trays. It is used to clean wood, porcelain, metal furniture, and most types of flooring. It can even be used as a charcoal lighter fluid.

LIMITATIONS: DO NOT HEAT container. DO NOT USE on asphalt, rubber tile, or around plugged-in electric motors or gas fired heaters.

APPLICATION: LN-1 Mineral Spirits when being used as a thinner can be introduced directly into the product to increase volume or reduce solids percentage. LN-1 Mineral Spirits when being used as a cleaner should not over saturate item being cleaned. LN-1 Mineral Spirits when being used as a charcoal lighter fluid should again not oversaturate the charcoal. Make sure cont- ainer is closed and a safe distance from burner before ignition. Also allow sufficient time for fluid to burn off before using.

STORAGE: LN-1 Mineral Spirits should be stored in a cool area and keep away from heat and open flames.

COMPOSITION: Mineral Spirits CAS 64741-41-9 This information is to assist customers in determining if this product is suitable for the proposed application, and to satisfy themselves as to suitability of the contents. Nothing herein shall constitute a warranty, expressed or implied, including any warranty of merchantability or fitness, nor is protection from law or patent implied.

® AQUACHECKTM

LN-1CUT SHEET

IBP - INTERNATIONAL BUILDING PRODUCTS, LLC.2711 N. Main Street • East Peoria Illinois 61611 • USA

LN-12 QUICK DRYING ASPHALT GILSONITE PAINT

PRODUCT DESCRIPTION:

LN-12 Gilsonite Paint is a superior quick drying asphalt paint formulated to meet Federal Specification TTC-494 Types I, II, and III.

BASIC USES: LN-12 Gilsonite Paint is used as a tough and weather resistant coating on all types of steel, piping, industrial equipment chassis, radiators, burial vaults, etc.

LIMITATIONS: DO NOT HEAT container.

APPLICATION: LN-12 Gilsonite Paint may be brushed or sprayed onto a clean and dry surface. This material dries in one hour and cures in approximately five hours.

STORAGE: LN-12 Gilsonite Paint should be kept in a warm area before usage during cold seasons, but this material can be used year round and the only protection would be from weathering on the container.

COMPOSITION: Asphalt Mineral Spirits Gilsonite

CAS 8052-42-4 CAS 64741-41-9 CAS 12002-43-6

This information is to assist customers in determining if this product is suitable for the proposed application, and to satisfy themselves as to suitability of the contents. Nothing herein shall constitute a warranty, expressed or implied, including any warranty of merchantability or fitness, nor is protection from law or patent implied.

® AQUACHECKTM

LN-12CUT SHEET

IBP - INTERNATIONAL BUILDING PRODUCTS, LLC.2711 N. Main Street • East Peoria Illinois 61611 • USA

LN-52 BLACK ASPHALT FENCE PAINT

PRODUCT DESCRIPTION:

LN-52 Black Asphalt Fence Paint is a high quality asphalt cutback fence paint.

BASIC USES: LN-52 Black Asphalt Fence Paint is used as a protective coating and moisture barrier on all types of wood and steel structures.

LIMITATIONS: DO NOT HEAT container.

APPLICATION: LN-52 Black Asphalt Fence Paint must be applied to a surface that is dry and clean from all foreign matter. This material can be applied with roller, brush or spray equipment and should yield a coverage rate with 12-13 gallons of 400 linear feet on three board fences.

STORAGE: LN-52 Black Asphalt Fence Paint can be used year round and the only protection would be from weathering on the container.

COMPOSITION: Asphalt Mineral Spirits HydrocarbonResin

CAS 8052-42-4 CAS 64741-41-9 CAS

This information is to assist customers in determining if this product is suitable for the proposed application, and to satisfy themselves as to suitability of the contents. Nothing herein shall constitute a warranty, expressed or implied, including any warranty of merchantability or fitness, nor is protection from law or patent implied.

® AQUACHECKTM

LN-52CUT SHEET

IBP - INTERNATIONAL BUILDING PRODUCTS, LLC.2711 N. Main Street • East Peoria Illinois 61611 • USA

LN-3100 BLACK NET SET

PRODUCT DESCRIPTION:

LN-3100 Black Net Set is an asphalt cutback formulated as a protective coating.

BASIC USES: LN-3100 Black Net Set is used as a protective coating that penetrates nets and coats crabpots.

LIMITATIONS: DO NOT HEAT container.

APPLICATION: LN-3100 Black Net Set should be applied to nets and crabpots, which are dry and oil free. The item should be dipped for approximately twenty minutes and taken out and allowed to dry.

STORAGE: LN-3100 Black Net Set can be used year round and the only protection would be from weathering on the container.

COMPOSITION: Asphalt Mineral Spirits HydrocarbonResin

CAS 8052-42-4 CAS 64741-41-9 CAS 12002-43-6

This information is to assist customers in determining if this product is suitable for the proposed application, and to satisfy themselves as to suitability of the contents. Nothing herein shall constitute a warranty, expressed or implied, including any warranty of merchantability or fitness, nor is protection from law or patent implied.

® AQUACHECKTM

LN-3100CUT SHEET

IBP - INTERNATIONAL BUILDING PRODUCTS, LLC.2711 N. Main Street • East Peoria Illinois 61611 • USA

MP-33 HEAVY DUTY INDUSTRIAL MASTIC

PRODUCT DESCRIPTION:

MP-33 Heavy Duty Industrial Mastic meets TT-C-520 specifications and is 100% ASBESTOS-FREE. This material is a self-healing type asphalt cutback fortified with fibres and fillers.

BASIC USES: MP-33 Heavy Duty Industrial Mastic is a multi-purpose protective coating used as a moisture barrier on felt and metal roofs, siding, and masonry surfaces above and below grade.

LIMITATIONS: DO NOT HEAT container.

APPLICATION: MP-33 Heavy Duty Industrial Mastic must be applied to a surface that is dry and clean of all foreign matter. This material should be kept in a warm area and stirred before use. This material can be applied by brush or trowel at a rate of 40 square feet per gallon.

STORAGE: MP-33 Heavy Duty Industrial Mastic can be used year round and the only protection would be from weathering on the container.

COMPOSITION: Asphalt Mineral Spirits Fibre Amino Salt Clay

CAS 8052-42-4 CAS 64741-41-9 CAS 65996-61-4 CAS 30113-45-2 CAS 8031-18-3

This information is to assist customers in determining if this product is suitable for the proposed application, and to satisfy themselves as to suitability of the contents. Nothing herein shall constitute a warranty, expressed or implied, including any warranty of merchantability or fitness, nor is protection from law or patent implied.

® AQUACHECKTM

MP-33CUT SHEET

IBP - INTERNATIONAL BUILDING PRODUCTS, LLC.2711 N. Main Street • East Peoria Illinois 61611 • USA

MP-48 WOOD BLOCK MASTIC

PRODUCT DESCRIPTION:

MP-48 Wood Block Mastic is an asphalt cutback with fibres and additives to perform as a floor block mastic binder and is 100% ASBESTOS-FREE.

BASIC USES: MP-48 Wood Block Mastic is used for adhering wood block flooring and wooden subflooring in gymnasiums to concrete or wood base. This material also can be used in conjunction with a dampproofing membrane.

LIMITATIONS: DO NOT HEAT container.

APPLICATION: MP-48 Wood Block Mastic must be applied to surface free of all foreign matter. This material should be applied with a notched trowel and should yield a coverage rate of 40-50 square feet per gallon or use wood block manufacturers recommendation.

STORAGE: MP-48 Wood Block Mastic can be used year round and the only protection would be from weathering on the container.

COMPOSITION: Asphalt Mineral Spirits Fibre Amine Salt Clay

CAS 8052-42-4 CAS 64741-41-9 CAS 65996-61-4 CAS 9004-34-6 CAS 30113-45-2 CAS 8031-18-3

This information is to assist customers in determining if this product is suitable for the proposed application, and to satisfy themselves as to suitability of the contents. Nothing herein shall constitute a warranty, expressed or implied, including any warranty of merchantability or fitness, nor is protection from law or patent implied.

® AQUACHECKTM

MP-48CUT SHEET

IBP - INTERNATIONAL BUILDING PRODUCTS, LLC.2711 N. Main Street • East Peoria Illinois 61611 • USA

MP-49 BRICK BLOCK MASTIC

PRODUCT DESCRIPTION:

MP-49 Brick Block Mastic is an asphalt cutback with fibres and latex additives to perform as a brick block mastic binder and is 100% ASBESTOS-FREE.

BASIC USES: MP-49 Brick Block Mastic is used for adhering brick or block in a paving application. This material also can be used in conjunction with a dampproofing membrane.

LIMITATIONS: DO NOT HEAT container.

APPLICATION: MP-49 Brick Block Mastic must be applied to surface free of all foreign matter. This material should be applied with a notched trowel and should yield a coverage rate of 40-50 square feet per gallon or use block or brick pavers manufacturers recommendation.

STORAGE: MP-49 Brick Block Mastic can be used year round and the only protection would be from weathering on the container.

COMPOSITION: Asphalt Mineral Spirits Fibre Mineral Filler Amine Salt Clay Latex

CAS 8052-42-4 CAS 64741-41-9 CAS 65996-61-4 CAS 1318-94-1 CAS 30113-45-2 CAS 8031-18-3 CAS 9003-18-3

This information is to assist customers in determining if this product is suitable for the proposed application, and to satisfy themselves as to suitability of the contents. Nothing herein shall constitute a warranty, expressed or implied, including any warranty of merchantability or fitness, nor is protection from law or patent implied.

® AQUACHECKTM

MP-49CUT SHEET

IBP - INTERNATIONAL BUILDING PRODUCTS, LLC.2711 N. Main Street • East Peoria Illinois 61611 • USA

MP-52 BITUMINOUS JOINT COMPOUND

PRODUCT DESCRIPTION:

MP-52 Bituminous Joint Compound is a trowel mastic asphaltic compound for joint sealing and is 100% ASBESTOS-FREE.

BASIC USES: MP-52 Bituminous Joint Compound is used as a joint sealant for concrete pipe, foundations, and all other masonry and steel joint sealing.

LIMITATIONS: DO NOT HEAT container.

APPLICATION: MP-52 Bituminous Joint Compound can be applied by trowel in a liberal fashion to fill the joint completely.

STORAGE: MP-52 Bituminous Joint Compound can be used year round and the only protection would be from weathering on the container.

COMPOSITION: Asphalt Mineral Spirits Fibre Amine Salt Clay

CAS 8052-42-4 CAS 64741-41-9 CAS 65996-61-4 CAS 9004-34-6 CAS 30113-45-2 CAS 8031-18-3

This information is to assist customers in determining if this product is suitable for the proposed application, and to satisfy themselves as to suitability of the contents. Nothing herein shall constitute a warranty, expressed or implied, including any warranty of merchantability or fitness, nor is protection from law or patent implied.

® AQUACHECKTM

MP-52CUT SHEET

IBP - INTERNATIONAL BUILDING PRODUCTS, LLC.2711 N. Main Street • East Peoria Illinois 61611 • USA

SL-5 SILICONE CLEAR GUARD

PRODUCT DESCRIPTION:

SL-5 Silicone Clear Guard meets Federal Specification SS-W-00110C specifications. This material is formulated to be a clear silicone mixture with solvent.

BASIC USES: SL-5 Silicone Clear Guard is used to produce a moisture barrier on brick and masonry surfaces, but also allows for the structure to breathe and evaporate moisture.

LIMITATIONS: DO NOT HEAT container.

APPLICATION: SL-5 Silicone Clear Guard must be applied to a surface that is dry and free of all foreign matter. This material may be applied by brush or spray equipment and should yield a coverage rate of 150 square feet per gallon on concrete or hard brick.

STORAGE: SL-5 Silicone Clear Guard can be used year round and the only protection would be from weathering on the container.

COMPOSITION: Silicone Resin Mineral Spirits

Trade Secret CAS 64741-41-9

This information is to assist customers in determining if this product is suitable for the proposed application, and to satisfy themselves as to suitability of the contents. Nothing herein shall constitute a warranty, expressed or implied, including any warranty of merchantability or fitness, nor is protection from law or patent implied.

® AQUACHECKTM

SL-5CUT SHEET

IBP - INTERNATIONAL BUILDING PRODUCTS, LLC.2711 N. Main Street • East Peoria Illinois 61611 • USA

EM-12 ASPHALT EMULSION METAL DUCTAL PIPE COAT

PRODUCT DESCRIPTION:

EM-12 Pipe Coat is a single component non-flammable highly rubberized asphalt emulsion modified with polymers and plasticizers.

BASIC USES: EM-12 Pipe Coat is a sprayable coating designed to protect from corrosion, waterproofing, environmental elements and achieves excellent durability and flexibility.

LIMITATIONS: DO NOT ALLOW material to freeze. DO NOT THIN material.

APPLICATION: EM-12 Pipe Coat must be applied to a surface that is free from all foreign matter. This material should remain dry until it has cured. This material should be mixed before using and yields a coverage of 250-350 square feet per gallon.

STORAGE: EM-12 Pipe Coat must be kept from freezing.

MATERIAL Weight per Gallon @ 770F, ASTM-D-1010, (lbs) 8.5-8.7

SPECIFICATIONS: Nonvolatile %, ASTM-D-2939 55.0-60.0

Viscosity @ 770F, ASTM-D-562 (Kreb's Stormer Unit) 55-65 KU

Softening Point (00F), ASTM-D-36 185-200

Penetration (0.1 mm), ASTM-D-5 10-2

Std. Spec. for Emulsified Asphalt AASHTO Designation M140-70 ASTM Designation D997-73

meets spec. meets spec.

Resistance to water, ASTM-D-2939 no blistering, no loss of adhesion, no re-emulsification

Dry Time (hrs.) ASTM-D-2939 less than 1

Shelf Life (yrs.) 1-2

This information is to assist customers in determining if this product is suitable for the proposed application, and to satisfy themselves as to suitability of the contents. Nothing herein shall constitute a warranty, expressed or implied, including any warranty of merchantability or fitness, nor is protection from law or patent implied.

® AQUACHECKTM

EM-12CUT SHEET

IBP - INTERNATIONAL BUILDING PRODUCTS, LLC.2711 N. Main Street • East Peoria Illinois 61611 • USA

SC-700 CAR INDUSTRIAL UNDERCOAT

PRODUCT DESCRIPTION:

SC-700 Heavy Duty Industrial Undercoat meets TT-C-520 specifications and is 100% ASBESTOS-FREE. This material is a self-healing type asphalt cutback fortified with fibres and fillers.

BASIC USES: SC-700 Heavy Duty Industrial Undercoat is a multi-purpose protective coating used as a protective undercoat on cars and trailers.

LIMITATIONS: DO NOT HEAT container.

APPLICATION: SC-700 Heavy Duty Industrial Undercoat must be applied to a surface that is dry and clean of all foreign matter. This material should be kept in a warm area and stirred before use. This material can be applied by brush or trowel at a rate of 40 square feet per gallon.

STORAGE: SC-700 Heavy Duty Industrial Undercoat can be used year round and the only protection would be from weathering on the container.

COMPOSITION: Asphalt Mineral Spirits Fibre Amino Salt Clay

CAS 8052-42-4 CAS 64741-41-9 CAS 65996-61-4 CAS 30113-45-2 CAS 8031-18-3

This information is to assist customers in determining if this product is suitable for the proposed application, and to satisfy themselves as to suitability of the contents. Nothing herein shall constitute a warranty, expressed or implied, including any warranty of merchantability or fitness, nor is protection from law or patent implied.

® AQUACHECKTM

SC-700CUT SHEET

IBP - INTERNATIONAL BUILDING PRODUCTS, LLC.2711 N. Main Street • East Peoria Illinois 61611 • USA