aqua2use gwdd - technical data gwdd - technical data-file027257.pdfaqua2use® gwdd filters and...

Technical Data 26 Quarry Spring, Harlow-Essex CM20 3HP – Tel 01279 311613 – Fax 01279 316105 e-mail:[email protected] – www.shielco.com Aqua2use ® GWDD Filters and recycles Greywater for garden irrigation Aqua2use Greywater Filtration Step 1: When the Aqua2use GWDD valve is open, greywater flows directly to the mains sewage. Step 2: When the Aqua2use GWDD valve is closed, greywater from the house is diverted to the inlet of the filter. Step 3: The greywater flows through the 1st filter web that retains major and medium particles such as hair, lint, paper, detergent clogs and other impurities. (The filter web: Matala Black - low density, Matala Green - medium density) Step 4: The greywater flows through the 2nd filter web that retains medium and small particles. (The filter web: Matala Green - medium density, Matala Blue - high density) Step 5: The greywater flows through the 3rd filter web that retains small and minor particles. (The filter web: Matala Blue - high density. Matala Gray - super high density) Step 6: Filtered greywater is pumped to the irrigation. Cross-flow depth filtration + Multichamber plug flow concept A pump designed for greywater The pump is different in 3 ways: 1. There is no single float to turn it on and off. There are two magnetic micro floats that activate the control box that senses the water level. This allows for the full capacity of the tank to be used, it allows for a full flow of water to be distributed thus filling your drip tube and importantly reaching the end of your drip tube line. It also means that the pump isn't cycling (switching on and off) unnecessarily and that the full surface area of the filters are exposed to the incoming greywater. 2. The control box switches the pump on independently of the magnetic floats. This makes sure the minimum residual is remaining in the tank. 3. There are no external timers in the Aqua2use. Other units may have to rely on external timers to make sure any residual is pumped out within 24 hours. The Aqua2use control box automatically turns on the pump to see if there is any residual water

Upload: others

Post on 02-Jun-2020

8 views

Category:

Documents

0 download

Report

Download

Embed Size (px):

TRANSCRIPT

Technical Data

26 Quarry Spring, Harlow-Essex CM20 3HP – Tel 01279 311613 – Fax 01279 316105 e-mail:[email protected] – www.shielco.com

Aqua2use® GWDD Filters and recycles Greywater for garden irrigation

Aqua2use Greywater Filtration

Step 1: When the Aqua2use GWDD valve is open, greywater flows directly to the mains sewage. Step 2: When the Aqua2use GWDD valve is closed, greywater from the house is diverted to the inlet of the filter. Step 3: The greywater flows through the 1st filter web that retains major and medium particles such as hair, lint, paper,

detergent clogs and other impurities. (The filter web: Matala Black - low density, Matala Green - medium density) Step 4: The greywater flows through the 2nd filter web that retains medium and small particles. (The filter web: Matala

Green - medium density, Matala Blue - high density) Step 5: The greywater flows through the 3rd filter web that retains small and minor particles. (The filter web: Matala

Blue - high density. Matala Gray - super high density) Step 6: Filtered greywater is pumped to the irrigation.

Cross-flow depth filtration + Multichamber plug flow concept

A pump designed for greywater

The pump is different in 3 ways:

1. There is no single float to turn it on and off. There are two magnetic micro floats that activate the control box that senses the water level. This allows for the full capacity of the tank to be used, it allows for a full flow of water to be distributed thus filling your drip tube and importantly reaching the end of your drip tube line. It also means that the pump isn't cycling (switching on and off) unnecessarily and that the full surface area of the filters are exposed to the incoming greywater.

2. The control box switches the pump on independently of the magnetic floats. This makes sure the minimum residual is remaining in the tank.

3. There are no external timers in the Aqua2use. Other units may have to rely on external timers to make sure any residual is pumped out within 24 hours. The Aqua2use control box automatically turns on the pump to see if there is any residual water