april 1, 2016 - pestgon.compestgon.com/pdf/sds/4_2016_master labels.pdf · invict xpress granular...

3612 Ocean Ranch Blvd

Oceanside, CA 92056

Cell 760801.7572 • Office 877724.8100Office Fax: 866.724.8282

Pestgon

Website: www.pestgon.com E-mail: [email protected]

Did you know…Pestgon has a termite divison:

PestgonTermiteCall toll-free

877.499.7378for an inspection

Product Labels — April 1, 2016Important Disclosure.................................................................................................................... Page 2Advion Cockroach Gel Bait ..................................................................................................Pages 3- 5Avert Dry Flowable .................................................................................................................Pages 6, 7Avitrol ......................................................................................................................................... Pages 8, 9Bedlam Plus ......................................................................................................................... Pages 10, 11CB-80 ...................................................................................................................................... Pages 12, 13Contrac .................................................................................................................................. Pages 14, 15Deadline MP ......................................................................................................................... Pages 16-23Delta Dust ............................................................................................................................. Pages 24-34Demand CS ........................................................................................................................... Pages 35-42Eco PCO ACU ................................................................................................................................ Page 43Endzone ................................................................................................................................. Pages 44, 45Essentria IC3 .........................................................................................................................Pages 46-51Final ..........................................................................................................................................Pages 52, 53Fumitoxin Tablets ................................................................................................................Pages 54-98InVict Xpress Granular Bait ..................................................................................................... Page 99Martin’s Gopher Bait 50......................................................................................................... 00Maxforce FC Magnum ................................................................................................ Pages 101-103Maxforce Fly Spot Bait ............................................................................................... Pages 104, 105Maxforce Granular Fly Bait ................................................................................................... Page 106Niban FG ........................................................................................................................... Pages 107-113Onslaught FastCap ....................................................................................................... Pages 114-117Phantom ........................................................................................................................... Pages 118-129Precor 2000 Plus ........................................................................................................... Pages 130, 131Precor IGR ........................................................................................................................ Pages 132, 133PTB Phantom Pressurized.......................................................................................... Pages 134-137 Purge III ............................................................................................................................ Pages 138, 139Pyrethrin Fogger ........................................................................................................... Pages 140, 141Pyrocide 300 ................................................................................................................... Pages 142-145RCO Omega Gopher Grain Bait ............................................................................... Pages 146-148Talstar PL .......................................................................................................................... Pages 149-151 Termidor SC ..................................................................................................................... Pages 152-167Terro PCO .................................................................................................................................... Page 168Wasp Freeze .................................................................................................................... Pages 169, 170 ZP Rodent Oat Bait ...................................................................................................... Pages 171-175

Important Disclosure – Please read carefully – RETAIN FOR YOUR FILES — 4/1/2016 RIGHT TO KNOW: Prior to application of pesticides to your property, State law requires that you be given the following information:

CAUTION - PESTICIDES ARE TOXIC CHEMICALS. Structural Pest Control Operators are licensed and regulated by the Structural Pest Control Board and apply pesticides which are registered and approved for use by the California Department of Food and Agriculture and the United States Environmental Protection Agency. Registration is granted when the state finds that, based on existing scientific evidence, there are no appreciable risks if proper use conditions are followed or that the risks are outweighed by the benefits. The degree of risk depends upon the degree of exposure; so exposure should be minimized. If, within 24 hours following application, you experience symptoms similar to common seasonal illnesses comparable to the flu, contact your physician or poison control center (800-876-4766) and your pest control operator immediately. If rodenticide ingestion occurs, you may experience symptoms of mild shock/bleeding, an anticoagulant reaction.

For further information, contact any of the following:

Service Information: Pest Control Operator 877-724-8100, Pestgon Incorporated

Health Information: County Health Department Riverside 951-358-5000

Orange 714-834-4722

Los Angeles 213-250-8055

San Bernardino 800-442-2283

San Diego 619-692-8499

Application Information: County Ag Commissioner Riverside 951-955-3000

Orange 714-955-0100

Los Angeles 626-575-5466

San Bernardino 909-387-2115

San Diego 858-694-8980

Regulatory Information: Structural Pest Control Board 2005 Evergreen St., Ste 1500, Sacramento, CA 95825 • 916.561.8708

TERMS AND NOTICES: The total amount of this contract for any and all pest management service work is due and payable upon receipt of each billing invoice. Only target pests checked on the original contract are included in the Regular Scheduled Service (RSS). Should Pestgon Incorporated fail to comply with specifications of the service contract, they shall be given a thirty (30) day written notice to comply and render satisfactory service, and if, at the end of such thirty-day notice, unsatisfactory conditions persist, customer reserves the right to cancel the contract without further notice. In any case, either party shall give written notice thirty (30) days prior to cancellation date.

SERVICE GUARANTEE: The PESTGON INCORPORATED Service Guarantee is a promise to retreat target pests during the term of the service contract, not a guarantee of efficacy or safety. If necessary, PESTGON INCORPORATED agrees to call back during the Service Guarantee period unless otherwise noted and provide retreat service at no extra charge. After the SG period, it will be understood by both parties that target pests are controlled and any other pest management services are chargeable to the customer. Charges for Regular Scheduled Service shall continue uninterrupted by the Service Guarantee unless otherwise agreed. Upon being instructed or advised, either in writing or orally, if the customer fails to make proper preparations and/or corrections for pest management service, Pestgon Incorporated cannot assure satisfactory service and the Service Guarantee will be void.

RESPONSIBILITY: Customer agrees to inform PESTGON INCORPORATED of any allergic or pregnant persons occupying the premises prior to any indoor treatment and PESTGON agrees to make reasonable effort to inquire. PESTGON shall take every reasonable precaution to use pest control products labeled to provide the maximum safety required by the United States Environmental Protection Agency in order to protect persons, pets and plants. However, PESTGON is not responsible for their health or wellbeing. Customer agrees to follow all precautionary instructions, written or oral, and to hold pest control operator harmless from any and all claims, damages and expenses arising out of pests and/or pest management services pursuant to this contract.

PRIME CONTRACT: In compliance with the Structural Pest Control Board, the California Department of Food and Agriculture and the United States Environmental Protection Agency, this document, even as an addendum, is the prime contract for pest control services by and between PESTGON INCORPORATED and the owners and authorized agents of the property herein addressed. Consent by the Owner (s) or authorized agent (s) and performance by PESTGON of any part of this contract binds this contractual agreement and its terms as the prime contract. No other contractual agreement, attachments or addendum shall have any force to precede, prevail, invalidate, impair or negate this prime contract and its terms. Any changes to this contractual agreement shall be only by written agreement, which is and shall be expressly understood to be an addendum hereto. In case any one or more of the parts or provisions of this contractual agreement shall be invalid, illegal or unenforceable in any respect, the validity, legality and enforceability of the remaining parts and provisions contained herein shall not be in any way invalidated, negated, affected or impaired thereby.

PESTICIDE DISCLOSURE NOTICE: California law (8538 Business & Professions Code and 1940.4 California Code of Regulations) requires that we provide you with a pesticide disclosure notice and the following chemical information prior to our initial pest control service. Property Managers, please notify your tenants that there will be ongoing pest control performed on the exterior common areas. If we treat the interior of a unit, we will leave a copy of this pesticide disclosure notice inside the unit for the tenant.

CHEMICAL INFORMATION AND APPLICATION RATES PER EPA LABEL INSTRUCTIONS: Advion Cockroach Gel Bait = 0.6% Indoxacarb (S-Enantiomer) EPA 352-652 Avert Dry Flowable = 0.050% Abamectin B1, EPA 499-294 Avitrol = 0.5% 4-Aminopyridine, EPA 11649-4 Bedlam Plus Insecticide = 0.4% 3-phenoxybenzyl-(1RS, 3RS, 1RS, 3SR)-2, 2-dimethyl-3-(2- methylprop-1-enyl)

cycloproposanecarboxylate, 1.0% N-Ocyl bicycloheptene dicarboximide, Imicloprid 0.05%, EPA 1021-2569 CB-80 = 0.5% Pyrethrins, EPA 9444-175 Contrac Rodent Bait = 0.005% Bromadiolone, EPA 12455-79 Deadline M-Ps Snail Bait = 4% Metaldehyde, EPA 64864-38 Delta Dust = 0.05% Deltamethrin, EPA 432-772 Demand CS = 0.06% Lambda-Cyhalothrin, EPA 100-1066 EcoPCO ACU = 0.1% 2-Phenethyl Propionate, EPA 67425-14-655 Endzone = 4.4% AceTamiprid EPA 8033-114-279 Essentria IC3 Insect Concentrate = Rosemary Oil 10%, Geraniol 5%, Wintergreen Oil 37%, White Mineral Oil 40%,

Vanilin 3%, EPA Exempt Final All-Weather Blox = .005% Brodifacoum , EPA12455-89 Fumitoxin = 55% Aluminum Phosphide, EPA 72959-1-5857 InVict Express Granular Bait, Imidacloprid 0.5%, EPA 73079-14 Martins Gopher Grain Bait 50 = 0.5% Strychnine Alkaloid, EPA 53883-23 Maxforce FC Magnum=.05% Fipronl, EPA 432-1460 Maxforce Fly Spot Bait = 10% Imidacloprid, 1-[6-Chloro-3-pyridinyl)methyl], 0.1% Z-9-Tricosene, EPA 432-1455 Maxforce Granular Fly Bait = Imidacloprid, 1-[(g-chloro-3-pyridinyl)methyl]-N nitro-2-imidazolidin-imine_0.5% Z-9-

Tricosene_0.1%, EPA 432-1375

Niban = 0.5% Orthoboric Acid, EPA 64405-2 Onslaught FastCap Spider & Scorpion Insecticide = 6.40% Esfenvalerate, 1.60% Prallethrin, 8.0% Piperonyl

Butoxide, EPA 1021-2574 Phantom Insecticide = 21.45% Chlorfenapyr, EPA 241-392 Precor 2000 Plus = 0.085% Methoprene, 0.35% pemethrin, 0.3% Phenothrin, 2% N-octylbicycloheptene,

dicarboximide, 1.4% Piperonyl butoxide, EPA 2724-490 Precor Plus IGR = 1.2% [S]-Methoprene EPA 2724-352 PTB Phantom II Pressurized = 0.5% ChlorFenapyr.4-bromo-2(4-chlorophenyl)-1-(eThoxymethyl)-5-(trifluorometh-

yl)-1H-Pyrrole-3-Caronitrile, EPA 499-548 Purge III Insecticide = 0.975% Pyrethrins, 1.950% Piperonyl Butoxide, 3.05% N-octylbicyclopheptene, EPA 279-

3388 Pyrethrin Fogger = 0.5% Pyrethrins, 1% Piperonyl Butoxide, technical, 1% N-OctylBicycloheptene Dicarboximide,

EPA 11623-GA-1 Pyrocide 300 = 3.0% Pyrethrins - 6.0% *Piperonyl butoxide, Technical ** 9.57% N-Octly bicychloheptene

dicabonximide, EPA 1021-1177 RCO Omega Gopher Grain Bait = 0.5% Strychnine Alkaloid, EPA-5042-32 Talstar PL Granular, 0.2 Bifenthrin, EPA 279-3168 Termidor SC = 9.1% Fipronil, EPA 7969-210 Terro PCO Liquid Ant Bait Stations = 5.40% Sodium Tetraborate Decahydrate (Borax) EPA-149-8-64405 Wasp-Freeze = 0.129% Allethrin, EPA-499-362 ZP Rodent Bait = 2% Zinc Phosphide, EPA-12455-17

Pestgon Incorporated, 3612 Ocean Ranch Blvd, Oceanside, CA 92056-2669 • 877-724-8100 www.pestgon.com • [email protected]

FIRST AIDHave the product container or label with you when calling a poison control center or doctor, or going for treatment.

HOT LINE NUMBERFor 24-Hour Medical Emergency Assistance

(Human or Animal) Or Chemical Emergency Assistance (Spill, Leak, Fire or Accident) Call 1-800-888-8372

PRECAUTIONARY STATEMENTS

HAZARDS TO HUMANS AND DOMESTIC ANIMALSCAUTION: Avoid contact with skin, eyes or clothing. Wash thoroughly with soap and water after handling. Prolonged or frequently repeated skin contact may cause allergic reactions in some individuals.

Environmental HazardsDo not apply directly to water, or to areas where surface water is present or to intertidal areas below the mean high water mark.

Physical and Chemical HazardsDo not use this product in or on electrical equipment where a possibility of shock hazard exists.

DIRECTIONS FOR USEIt is a violation of federal law to use this product in a manner inconsistent with its labeling.

PRODUCT INFORMATIONAdvion® Cockroach Gel Bait is designed to control pest species of cockroaches such as German, American, Australian, Smoky-Brown, Brown, Asian, Oriental, and Brown-Banded.

Use Instructions and Precautions:Do not treat areas that are easily accessible to children and pets.1. Advion Cockroach Gel Bait can be used indoors or

outdoors applied as a crack and crevice treatmentwithin residential homes, industrial facilities, offices,warehouses, commercial kitchens, hospitals, schools,nursing homes, hotels, buses, trains, aircraft, retail andcommercial establishments, and other areas infestedwith cockroaches.

2. Apply Advion Cockroach Gel Bait to areas frequentedby cockroaches such as between different elements ofconstruction, between equipment and floors, openingsleading into voids and hollow spaces in floors, walls,ceilings, equipment legs and bases, around plumbingpipes, doors and windows, and behind and underappliances, cabinets, sinks, closets, and any otherequipment that cockroaches are typically known tohide.

3. Do not apply Advion Cockroach Gel Bait to surfacesrecently treated with residual sprays.

4. Do not apply residual sprays to surfaces treated withAdvion Cockroach Gel Bait.

5. Inspect bait placements during follow-up inspections andapply fresh bait as needed.

6. Do not apply to surfaces that food contacts.7. Do not allow open foods to contact gel material.

InsecticideFOR USE IN RESIDENTIAL, INSTITUTIONAL,COMMERCIAL, AND INDUSTRIAL AREASUse sites include single and multi-family residentialbuildings, schools, commercial and industrial facilities (including warehouses, apartments, supermarkets, restaurants, motels, hotels, hospitals, food handling/storage establishments), and transportation equipmentsuch as aircraft, trains, ships, boats, buses.

Active Ingredient:Indoxacarb:(S)-methyl 7-chloro-2,5-dihydro-2-[[(methoxycarbonyl)[4(trifluoromethoxy) phenyl]amino]carbonyl]indeno[1,2-e][1,3,4]oxadiazine-4a-(3H)carboxylate . . . . . . . . . . . . . . 0.6%

Other Ingredients 99.4%

Total: 100.0%

KEEP OUT OF REACH OF CHILDREN

CAUTION/PRECAUCIÓNSi usted no entiende la etiqueta, busque a alguien para quese la explique a usted en detalle. (If you do not understand the label, find someone to explain it to you in detail.)

DO NOT TREAT AREAS THAT ARE EASILY ACCESSIBLE TO CHILDREN AND PETS

EPA Reg. No. 100-1484EPA Est. 54450-IL-001ABW

EPA Est. 65335-RI-001NSP

(Superscript is first three letters of batch code on container)

Product of USA

SCP 1484A-L1A 0414

4 x 1.06 oz. (30g) syringesNet WeightNon-refillable Container

Return to Index...

Treatment Rates for All Uses For heavy infestations of cockroaches, apply 3 to 5 spots of Advion Cockroach Gel Bait per 10 linear feet. For light to moderate infestations of cockroaches, apply 1-3 spots of Advion Cockroach Gel Bait per 10 linear feet. Each spot of ADVION® cockroach gel bait must equal about 0.5 grams (approx. 1/4” diameter) For all levels of cockroach infestations, when a bead of Advion Cockroach Gel Bait is used, apply a small thin bead that is less than 1/8” wide and approximately 2 inches long.

Indoor Use Directions Infested areas must be carefully inspected to determine overall infestation levels, locations of harborage areas, and most appropriate application points. Apply Advion Cockroach Gel Bait as a small spot of material, approximately 0.5 grams (approx. 1/4” in dia.), to areas not able to be contacted by children or pets. Several small applications distributed within an area are more effective than 1 or 2 applications of large quantities. In some cases a small thin bead (less than 1/8” wide and 2” long) may be appropriate such as between construction elements or other cracks and crevices. Indoor applications include cracks and crevices along walls or floors, behind or under equipment, under tables, within framing of tables or furniture, around sinks, within or near garbage collection areas, attics, crawl spaces, and cracks and crevices in cabinets. Inspect Advion Cockroach Gel Bait placements periodically for consumption or attractiveness and reapply as needed.

Applications in Nonfood/Nonfeed Handling AreasAdvion Cockroach Gel Bait is designed for use as a spot or crack and crevice treatment to control cockroaches in residential structures and the non-food /non-feed areas of commercial, industrial, public and institutional buildings/structures, including restaurants, warehouses, food processing plants, supermarkets, hospitals, nursing homes, motels, hotels, schools, laboratories, computer facilities, aircraft, buses, boats/ships, trains, pet shops and zoos.Nonfood/non-feed areas include areas such as garbage rooms, lavoratories, floor drains (to sewers), entries, and vestibules, offices, locker rooms, machine rooms, boiler rooms, garages, mop closets and storage (after bottling or canning). Refer to section below for use directions and restrictions when making applications in food/feed handling areas of Food/Feed Handling Establishments.

Applications in Food/Feed Handling AreasApplication to food/feed areas of food/feed handling establishments may only be made as a crack and crevice treatment only. Apply Advion Cockroach Gel Bait directly into cracks and crevices by placing the bait dispenser tip approximately 1/2 inch into cracks, crevices, holes and similar openings where cockroaches are found or are entering.Food and feed handling areas include areas for receiving, storage, packing (canning, bottling, wrapping, boxing), preparing edible waste storage, and enclosed processing systems (mills, dairies, edible oils, syrups). Serving areas are also considered a food/feed area when food is exposed and facility is in operation.

Do not apply Advion Cockroach Gel Bait to areas where food/feed, food utensils or food processing surfaces may come into contact and become contaminated. Do not apply Advion Cockroach Gel Bait to areas that are routinely washed such as cracks and crevices in tops of tables, food/feed preparation and prepared food holding surfaces as bait could be removed by the washing. Do not apply Advion Cockroach Gel Bait to surfaces where the temperature exceeds 120-130°F because this could cause the bait to liquefy and lose effectiveness. Examples include, but are not limited to, parts of stoves, ovens, grills, fume hoods, saunas, heat lamps, coffee urns, steam tables, toasters, fryers, dishwashers, and hot water pipes. Use good application practice to avoid movement of Advion Cockroach Gel Bait to exposed surfaces used for food preparation. If Advion Cockroach Gel Bait contacts an exposed surface, first remove as much of the gel bait as possible, then wash with soap and water.

Outdoor Use Directions:A thorough inspection around a structure may reveal areas where cockroaches are gaining access. Attempts should be made to remove the access. Advion Cockroach Gel Bait may also be applied as a spot or thin bead (see above) to pest entry sites such as along windows, doors, between construction elements, sewer areas, adjacent trees which harbor cockroaches, along walls, garbage holding areas, or suitable placement site acting as a cockroach harborage. Place baits in such a way as to reduce the potential of subsequent human contact. Inspect Advion Cockroach Gel Bait placements periodically and apply fresh bait as needed.

STORAGE AND DISPOSALDo not contaminate water, food or feed by storage and disposal.

Pesticide StorageStore in cool, dry place inaccessible to children and pets.

Pesticide DisposalWastes resulting from the use of this product must be disposed of on site or at an approved waste disposal facility.

Container DisposalNonrefillable Container: Do not reuse or refill this container. Offer for recycling if available. Place empty bait dispensers in trash. If partially filled, wrap in newspaper and discard in trash or call your local solid waste authority for disposal instructions.

CONDITIONS OF SALE AND LIMITATIONOF WARRANTY AND LIABILITY

NOTICE: Read the entire Directions for Use and Conditions of Sale and Limitation of Warranty and Liability before buying or using this product. If the terms are not acceptable, return the product at once, unopened, and the purchase price will be refunded.

The Directions for Use of this product must be followed carefully. It is impossible to eliminate all risks inherently associated with the use of this product. Crop injury, ineffectiveness or other unintended consequences mayresult because of such factors as manner of use or application, weather or crop conditions, presence of other materials or other influencing factors in the use of the product, which are beyond the control of SYNGENTA CROP PROTECTION, LLC or Seller. To the extent permitted by applicable law, Buyer and User agree to hold SYNGENTA and Seller harmless for any claims relating to such factors.SYNGENTA warrants that this product conforms to the chemical description on the label and is reasonably fit for the purposes stated in the Directions for Use, when used in accordance with directions under normal use conditions. To the extent permitted by applicable law: (1) this warranty does not extend to the use of this product contrary to label instructions or under conditions not reasonably foreseeable to or beyond the control of Seller or SYNGENTA, and (2) Buyer and User assume the risk of any such use. TO THE EXTENT PERMITTED BY APPLICABLE LAW, SYNGENTA MAKES NO WARRANTIES OF MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE NOR ANY OTHER EXPRESS OR IMPLIED WARRANTY EXCEPT AS WARRANTED BY THIS LABEL.To the extent permitted by applicable law, in no event shall SYNGENTA be liable for any incidental, consequential or special damages resulting from the use or handling of this product. TO THE EXTENT PERMITTED BY APPLICABLE LAW, THE EXCLUSIVE REMEDY OF THE USER OR BUYER, AND THE EXCLUSIVE LIABILITY OF SYNGENTA AND SELLER FOR ANY AND ALL CLAIMS, LOSSES, INJURIES OR DAMAGES (INCLUDING CLAIMS BASED ON BREACH OF WARRANTY, CONTRACT, NEGLIGENCE, TORT, STRICT LIABILITY OR OTHERWISE) RESULTING FROM THE USE OR HANDLING OF THIS PRODUCT, SHALL BE THE RETURN OF THE PURCHASE PRICE OF THE PRODUCT OR, AT THE ELECTION OF SYNGENTA OR SELLER, THE REPLACEMENT OF THE PRODUCT.SYNGENTA and Seller offer this product, and Buyer and User accept it, subject to the foregoing Conditions of Sale and Limitation of Warranty and of Liability, which may not be modified except by written agreement signed by a duly authorized representative of SYNGENTA.

Advion®, the ALLIANCE FRAMEthe SYNGENTA Logo and the PURPOSE ICONare Trademarks of a Syngenta Group Company

©2014 Syngenta

For non-emergency (e.g., current product information),call Syngenta Crop Protection at 1-800-334-9481.

Manufactured for:Syngenta Crop Protection, LLCP.O. Box 18300Greensboro, North Carolina 27419-8300

SCP 1484A-L1A 0414

• Crack & Crevice® Bait • Kills Cockroaches • Contains approximately 200 bait placementsKILLS:Ants, Booklice, Carpet Beetles, Cockroaches (including carbamate, organophosphate, organochlorine and pyrethroid resistant strains), Crickets,Drugstore Beetles, Earwigs, Flour Beetles, Grain Weevils, Pillbugs and Sowbugs.FOR USE IN:Apartments, Campgrounds, Garages, Food Storage Areas, Homes, Hospitals and Nursing Homes (non-occupied patient areas), Hotels, MeatPacking and Food Processing Plants, Motels, Resorts, Restaurants and other Food Handling Establishments, Schools†, Supermarkets,Transportation Equipment (Buses, Boats, Ships, Trains, Trucks, Planes††), Utilities, Warehouses, and other Commercial and Industrial Buildings.† Do not apply to classrooms when in use.†† Do not apply in cockpit.

ACTIVE INGREDIENTS:Abamectin* B1: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.050%Related Compounds: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.004%OTHER INGREDIENTS: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99.946%* US Patent #4,678,774 TOTAL: 100.000%

EPA Reg. No. 499-294KEEP OUT OF REACH OF CHILDREN

CAUTIONFIRST AID

IF SWALLOWED: Call poison controlcenter or doctor immediately for treatmentadvice. Have person sip a glass of water ifable to swallow. Do not induce vomitingunless told to do so by the poison controlcenter or doctor. Do not give anything bymouth to an unconscious person.IF INHALED: Move person to fresh air. Ifperson is not breathing, call 911 or anambulance, then give artificial respiration,preferably mouth-to-mouth, if possible.Call a poison control center or doctor forfurther treatment advice.IF ON SKIN OR CLOTHING: Take offcontaminated clothing. Rinse skin immedi-ately with plenty of water for 15 - 20 min-utes. Call a poison control center or doctorfor treatment advice.IF IN EYES: Hold eyes open and rinseslowly and gently with water for 15 - 20minutes. Remove contact lenses, if present,after the first 5 minutes, then continue rins-ing eyes. Call a poison control center ordoctor for treatment advice.

Have the product container or label with youwhen calling a poison control center or doc-tor or going for treatment. You may also call1-800-225-3320 for emergency medicaltreatment information.

PRECAUTIONARY STATEMENTSHAZARDS TO HUMANS

AND DOMESTIC ANIMALSCAUTION: Harmful if swallowed, inhaled orabsorbed through the skin. Do not breathedust. Do not allow to contact skin, eyes orclothing. If contact occurs, wash skin withsoap and warm water, or eyes with clean water.Wash hands and exposed skin before eating,drinking or smoking and after handling.Wash all contaminated clothing thoroughlybefore re-use.Do not apply where children (or domestic ani-mals) are likely to come in frequent contactwith treated areas. Any powder visible afterapplication is complete should be brushedinto cracks or crevices or removed. No gener-alized dusting should be done in householdareas accessible to children or pets.

ENVIRONMENTAL HAZARDSThis pesticide is toxic to fish and wildlife. Donot apply directly to water. Do not contami-nate water by cleaning of equipment or dis-posal of equipment washwaters.This product is highly toxic to bees exposedto direct treatment or residues on bloomingcrops or weeds. Do not apply this product orallow it to drift to blooming crops or weedsif bees are visiting the treatment areas.

DIRECTIONS FOR USEIT IS A VIOLATION OF FEDERAL LAW TO

USE THIS PRODUCT IN A MANNERINCONSISTENT WITH ITS LABELING.

IMPORTANT NOTICE• Do not apply to humans, animals, clothing

or bedding.• Do not use on or contaminate fruit, veg-

etables or other food or feed crops.• Do not contaminate feed or food products

or food preparation surfaces, dishes,kitchen utensils and food containers.

WHITMIRE MICRO-GENRESEARCH LABORATORIES, INC.

NOTE: This specimen label is for informational purposes only. All uses may not be approved in all states. See labeling which accompanied product for Directionsfor Use or call 800-777-8570 for more information. FFoorr aauuttoommaattiicc ssppeecciimmeenn llaabbeell uuppddaatteess,, rreeggiisstteerr aatt wwwwww..wwmmmmgg..ccoomm..

AVERTDry Flowable Cockroach Bait Formula 1

®

Prescription Treatment brand®

Return to Index...

• Do not dispense this product with powerdusters in confined areas (i.e. attics, hotwater heater closets, furnace rooms, etc.)in the presence of open flames, such aspilot lights.

GENERAL INSTRUCTIONSAvert Dry Flowable is intended for applica-tion with the supplied hand duster to hidingand runway areas and those places wherepests are found. Apply insecticide directlyinto cracks and crevices. Apply lightly anduniformly to infested areas. Pay particularattention to cracks and crevices; serviceducts; false floors and ceilings; wall voids;around electrical and telephone fittings andequipment; around water and sewer pipes;under and behind cabinets, refrigerators andsinks; around window and door frames; andin attics and crawl spaces.The amount to be applied will vary with thesite. Concentrate treatment at insect activitysites. For light infestations, a minimum of4 - 6 bait points is recommended per 100sq. feet of treatment area. For heavy infesta-tions, a minimum of 12 - 24 bait points isrecommended per 100 sq. feet of treatmentarea. During follow-up visits, inspect baitplacements and reapply when necessary.

INDOOR TREATMENTSCOCKROACHES, ANTS AND CRICKETS:Apply thoroughly to all areas where thesepests crawl and hide, especially in cracksand crevices and hidden surfaces aroundsinks and storage areas, behind baseboards,around doors and windows, cabinets,stoves, behind refrigerators and in atticsand crawl spaces.EARWIGS, PILLBUGS AND SOWBUGS:Apply in cracks and crevices around doorsand windows and other places where these

pests may enter premises. Treat voids andother enclosed locations where these pestsare found.PANTRY PESTS - Including DrugstoreBeetles (exposed adult and larva stages),Flour Beetles and Grain Weevils:Remove all food and shelving paper beforetreatment. Treat cracks and crevices and/orvoids where these insects may be harboringor hibernating. Infested areas include, butare not limited to, cracks and crevices incabinets, pantries and wall voids. During fol-low-up visits, inspect bait placements andreapply when necessary. Cover shelves withshelving paper after treatment. Destroyinfested food packages.CARPET BEETLES - Including Black,Furniture and Varied: Apply to cracksand crevices where these insects are found.AIRCRAFT CABINS: Apply bait in sus-pected and infested cockroach areas. Place abait placement in areas between elements ofconstruction. Use 12 - 24 bait placementsper 100 sq. feet. Do not apply any bait incockpit area.FOOD AREAS OF FOOD/FEED HAN-DLING ESTABLISHMENTS: Food/feedhandling establishments are places otherthan private residences in which food/feed isheld, processed, prepared or served.APPLICATIONS OF AVERT DRYFLOWABLEIN FOOD AREAS OF FOODHANDLING ESTABLISHMENTS ARELIMITED TO CRACK & CREVICE®

TREATMENT ONLY. Food areas includeareas for receiving, storage, packing (can-ning, bottling, wrapping, boxing), preparing,edible waste storage and enclosed process-ing systems (mills, dairies, edible oils,syrups). Serving areas (when food isexposed and facility is in operation) would

also be considered a food area. Apply prod-uct according to the level of infestation asprescribed in the General Instructions intocracks and crevices associated with wallvoids, pieces of equipment, stainless steeltables, drains, storage equipment anddining tables. Also apply between elementsof construction. During follow-up visits,inspect bait placements and reapply whennecessary. Do not contaminate feed or foodproducts or food preparation surfaces, dish-es, kitchen utensils or food containers.

OUTDOOR TREATMENTSUse for control of ants, cockroaches, crick-ets, earwigs, ground beetles, pillbugs andsowbugs. Inject into cracks and crevicesaround windows and doors, porches,screens, eaves, patios, garages, under stair-ways and in crawl spaces and other areaswhere pests hide, such as tree holes andcracks in fences.

STORAGE AND DISPOSALDo not contaminate water, food or feed bystorage or disposal.STORAGE: Store in a tightly closed con-tainer in a cool, dry place.PESTICIDE DISPOSAL: Wastes result-ing from the use of this product may be dis-posed of on site or at an approved wastedisposal facility.CONTAINER DISPOSAL: Empty con-tainer by using the product according to thelabel directions. Do not reuse this contain-er! Place empty container in trash or offerfor recycling if available. If container ispartly filled, call your local solid wasteagency or 1-800-CLEANUP for disposalinstructions. NEVER PLACE UNUSEDPRODUCT DOWN ANY INDOOR OROUTDOOR DRAIN!

A Prescription Treatment® brand insecticide from:Whitmire Micro-Gen Research Laboratories, Inc.

3568 Tree Court Industrial Blvd.St. Louis MO 63122-6682

www.wmmg.com© 2005 Whitmire Micro-Gen Research Laboratories, Inc.

060321-52

Ave rt ® Dry Flowable Cockroach Bait Formula 1

NOTE: This specimen label is for informational purposes only. All uses may not be approved in all states. See labeling which accompanied product for Directionsfor Use or call 800-777-8570 for more information. FFoorr aauuttoommaattiicc ssppeecciimmeenn llaabbeell uuppddaatteess,, rreeggiisstteerr aatt wwwwww..wwmmmmgg..ccoomm..

!!!

AVITROL CORN CHOPS

Active Ingredient: 4-Aminopyridine……………………………………………………….0.5% Other Ingredients:…………………………..………………………………………………99.5%

Total:…………………………………………..……………………………………………..100.0%

Avitrol Corn Chops is a poison with flock alarming properties used for the control of House Sparrows (Passer domesticus), Red-winged (Agelaius phoeniceus), Yellow-headed (Xanthocephalus xanthocephalus), Rusty (Euphagus carolinus), and Brewers (Euphagus cyanocephalus) Blackbirds, Great-tailed (Quiscalus mexicanus) Boat-tailed (Quiscalus major) & Common (Quiscalus quiscula) Grackles, Brown-headed (Molothrus ater) & Bronzed (Molothrus aeneus) Cowbirds, and European Starlings (Sturnus vulgaris) in, on or in the area of structures, feeding, nesting, loafing and roosting sites, in such a way that a part of a flock may react and frighten the rest away. Birds that react and alarm a flock usually die.

IN NEW YORK STATE: Do not apply in cities with a population of one (1) million or more.Si usted no entiende la etiqueta, bosque a alguien para que se la explique a usted en detaile. (If you do not understand the label, find

someone to explain it to you in detail.)

KEEP OUT OF REACH OF CHILDREN CAUTION

Manufactured by EPA Reg. No. 11649-6 Avitrol Corporation EPA Est. 11649-OK-17644 East 46th St Tulsa, OK 74145-6370 (918) 622-7763 * (800) 633-5069

SPECIMEN LABEL

PRECAUTIONARY STATEMENTS HAZARDS TO HUMANS & DOMESTIC ANIMALS

CAUTION: Harmful if swallowed. May cause irritation. Avoid contact with eyes or clothing. Wash thoroughly with soap and water after handling.PERSONAL PROTECTIVE EQUIPMENT (PPE)

Most clothing, including cotton is resistant to this product. All mixers, loaders, applicators, persons picking up the dead birds and unused bait, and other handlers must wear the following PPE: Long-sleeved shirt and long pants, shoes plus socks, and chemical-resistant gloves (such as those made out of any waterproof material, Selection category A). Applicators shall use a scoop when mixing, applying, and broadcasting this product.

Note: Application continues until the dead birds and unused bait are retrieved – all participants in the application are pesticide handlers.

User Safety Requirements: After use, protective clothing should be washed in detergent and hot water. Keep and wash PPE separately from other laundry.ENVIRONMENTAL HAZARDS

Do not apply directly to water, or to areas where surface water is present, or to inter-tidal areas below the mean high water mark. This pesticide is extremely toxic to mammals and birds. This product is toxic to vertebrates. Wildlife and pets feeding on treated bait may be killed. Do not contaminate water by cleaning equipment or disposal of waste.

DIRECTIONS FOR USE RESTRICTED USE PESTICIDE

It is a violation of Federal Law to use this product in a manner inconsistent with its labeling. ENTRY RESTRICTIONS Keep persons (other than authorized handlers) as well as pets and livestock, away from the treated bait and dead or dying birds at all times. Only protected handlers may be in the area during bait application until all dead birds and unused bait is retrieved. USE RESTRICTIONS

• Avitrol Corn Chops must not be exposed in any manner that may endanger desirable and protected bird species. If there is a question of such hazard,consult local, state and federal game authorities before undertaking bird management with Avitrol Corn Chops.

RESTRICTED USE PESTICIDE DUE TO ACUTE ORAL AND ACUTE DERMAL TOXICITY AND DUE TO TOXICITY TO BIRDS AND MAMMALS

For retail sale to and use by only Certified Applicators or persons under their direct supervision and only for those uses covered by the Certified Applicator’s Certification.

User Safety Recommendations Users should wash hands before eating, drinking, chewing gum, using tobacco, or using the toilet. Users should remove clothing/PPE immediately if pesticide gets inside. Then wash thoroughly and put on clean clothing. Users should remove PPE immediately after handling this product. Wash the outside of gloves before removing. As soon as possible, wash thoroughly and change into clean clothing.

Return to Index...

• Investigate local laws that may prohibit the use of any toxic chemical in bird control. • Do not apply this product in a way that will contact workers or other persons, either directly or through drift. Only protected handlers may be in the area

during application. • Do not feed to livestock or poultry. Do not mix with grain for livestock or poultry feed. • Do not apply where livestock and/or poultry may be exposed. • Do not apply to growing food crops. • DO NOT apply treated bait in areas accessible to children. • Baits must be prepared and applied as specified on this label. • Do not apply baits made from this product by air or any mechanical equipment designed to broadcast baits or other pesticides. • Users of this product must follow all limitations indicated on this label regarding the placement, monitoring, and retrieval of treated baits. • Before baits made with this product are applied, sites that are to be treated must be observed for evidence of non-target activity and must be pre-baited

(see specific instructions for these activities). • In populated areas, and most areas open to the public, where feasible, baiting must be performed at elevated sites. • In areas open to the public, where baiting at elevated sites is not feasible, and ground baiting is required, a certified applicator or someone under his/her

direct supervision (authorized handler) must ensure children, pets and non-target species do not come in contact with the blend during the entire application period. That authorized handler must not leave the site until all dead/dying birds and unused bait are retrieved from the site. All dead/dying birds must be disposed of by burial or incineration.

• Do not apply treated baits within 25 feet of permanent bodies of water. • Do not apply baits made from this product in any way that could contaminate materials to be sued as human food or animal feed. • Do not use treated baits as food or feed. Do not store or even temporarily place treated bait in locations accessible to children, pets, or domestic animals. • Before applying treated baits in any problem area, carefully observe target birds’ feeding habits to locate their preferred feeding sites, determine the

optimum time of application, and evaluate options to reduce potential hazards of the application to desirable and/or protected animal species. • Pre-baiting with untreated bait materials is required to promote feeding by target species and to assess potential for exposure of non-target species. Do

not apply treated bait if non-target species are observed feeding on the pre-bait.

PREBAITING DIRECTIONS This product must not be applied where non-target birds are feeding. Careful observations of the birds’ feeding habits must therefore be made to establish proper feeding locations and to determine that no non-target birds are feeding on the pre-bait. Pre-baiting with untreated grains of the same composition as this product’s carrier is required. The target species are primarily ground feeders, therefore, place pre-bait at ground level when possible. When pre-baiting inside structures, in areas open to the public, pre-baiting may be performed on elevated flat surfaces, perching areas and ledges. Bait trays may be used but feeding acceptance will normally require more time.

DILUTION DIRECTIONS Thoroughly mix Avitrol Corn Chops with untreated corn chops, of the same composition, at the dilution ratios indicated below. For the control of Blackbirds, Grackles, Starlings and Cowbirds with Avitrol Corn Chops, do not use a dilution ratio less than one (1) part treated to five (5) parts untreated. House sparrows, however, usually operate within limited areas, with feeding and nesting sites relatively close to one another. Thus while ratios of one (1) part treated to nine (9) (or more) untreated parts have given good control in many instances, particularly stubborn cases may require a ratio of one (1) part treated to five (5) parts untreated. Greater numbers of birds may be killed however, as toxic bait is made less dilute.

BAITING DIRECTIONS To obtain minimal mortality, limit the distribution of Avitrol Corn Chops to scattered spot placements that will provide feeding opportunities only for the necessary number of target birds. After the birds’ feeding pattern has been established through pre-baiting, replace untreated bait with diluted treated bait only at sites where the target birds are actively feeding. Do not apply treated bait to inactive feeding sites. Where uneaten bait may be a hazard to other birds or animals, it must be picked up at the end of each day. When this product is used in or around occupied buildings, pick up and dispose of dead birds by burial or incineration. This product must not be applied where non-target bird species are feeding. When baiting with Avitrol Corn Chops, best results are usually obtained by rotating pre-baiting, (with untreated bait), with baiting, (with blended bait), until the desired control is obtained. Note that retreatment may also be necessary after rainfall.

9-8-13

STORAGE AND DISPOSAL Do not contaminate water, food, or feed by storage and disposal. Storage: Store only in original container in a cool, dry location inaccessible to children and pets. Store apart from food or animal feed and protect against rodent penetration of the carton. Store apart from other pesticides, fertilizers, food, or feed that may cause cross-contamination of odor or insect infestation. Pesticide Disposal: Pesticide wastes are acutely hazardous. Improper disposal of excess pesticide, spray mixture, or rinsate is a violation of Federal Law. If these wastes cannot be disposed of by use according to label instructions, contact your State Pesticide or Environmental Control Agency, or the Hazardous Waste representative at the nearest EPA Regional Office for guidance. Container Handling: Fiber Drums with Liners: Completely empty liner by shaking and tapping sides and bottom to loosen clinging particles. Empty residue into application equipment. Then dispose of liner in sanitary landfill or by incineration if allowed by State and local authorities. If drum is contaminated and cannot be reused, dispose of in the same manner.

Notice: Buyer and/or User assumes all risks of use and/or handling of these materials contrary to label instructions

Specimen Label

KILLS PYRETHROID RESISTANT BED BUGS AND THEIR EGGS.


CAUTIONSee inside for first aid and precautionary statements.

ACTIVE INGREDIENTS:3-phenoxybenzyl-(1RS, 3RS, 1RS, 3SR)-2,2-dimethyl-3-(2-methylprop-1-enyl) cyclopropanecarboxylate ...........0.40%N-Octyl bicycloheptene dicarboximide ..............................................1.00%Imidacloprid ....................................................................................0.05%OTHER INGREDIENTS ....................................................................98.55%

100.00%

DIRECTIONS FOR USEIt is a violation of Federal law to use this product in a manner inconsistent with its labeling.

USE RESTRICTIONS:

treated. Allow surfaces to dry before reoccupying.

serving areas.

covered or removed.

will occur.

occupants of the bed.SHAKE WELL BEFORE EACH USE.APPLICATION: Use as an indoor spot spray or crack and crevice treatment. Spray in an inconspicuous area to test for possible staining. Evaluate test area after drying. Hold container upright with nozzle aimed away from you. Depress valve and spray from a distance of 8 to 10 inches. Spray each square foot until damp. Use the straw applicator for crack and crevice treatment. Allow sprayed articles and surfaces to dry thoroughly before using. Do not allow children or pets to contact treated areas until surfaces are dry. TO KILL CRAWLING INSECTS: Apply as a spot or crack and crevice treatment where insects are harboring, traveling, or breeding. Treat interior entry points such as around windows, doors, and water pipes. Also treat feeding or hiding areas such as baseboards, carpet, floor, rugs, under refrigerators, cabinets, sinks, and stoves.

TO KILL BED BUGS AND BED BUG EGGS: For infested mattresses, remove linens and wash before reuse. Apply to tufts, folds, edges, sides and seams until damp. Allow to dry before reuse. Apply on and around baseboards, carpet, rugs, bed frames, box springs, headboards, wheelchairs, closets, wall hangings, furniture, seats, moldings, picture frames, ceiling, drapes, luggage, and walls. Spray bed bugs and eggs directly whenever possible. Use attached straw applicator for crack and crevice treatments.TO KILL BROWN DOG TICKS AND FLEAS: Spray on and around beds, furniture and pet’s habitat. Spray pet sleeping quarters, bedding, carpeting, floor and floor covering where pets are kept. Use only a recommended pet spray on pets.TO KILL DUST MITES: Thoroughly vacuum entire room concentrating on areas where mites congregate such as mattresses, box springs, headboards, walls, floors, carpeting, and baseboards. Spray surfaces until damp. Allow to dry before reuse.TO KILL CLOTHES MOTHS AND CARPET BEETLES: Apply as a spot treatment to cracks and crevices on and around baseboards, floorboards, furniture and around the edges of carpet. Apply to carpet, rugs, closets, baseboards, furniture, on floor and floor coverings. When treating carpets, floor coverings or rugs, spray a sufficient amount to get the spray down into the base where the larval stages are feeding. Spray upper and lower surfaces of rugs or floor covering when possible.

Return to Index...

STORAGE AND DISPOSALDo not contaminate water, food, or feed by storage and disposal.

PESTICIDE STORAGE: Store in a cool, dry area. Always store pesticides in the original container. Store away from food and pet food.

PESTICIDE DISPOSAL AND CONTAINER HANDLING: Do not puncture or incinerate!

Non-refillable container. Do not reuse or refill this container.

If empty: Place in trash or offer for recycling if available.

If partly filled: Call your local solid waste agency for disposal instructions.

PRECAUTIONARY STATEMENTSHAZARDS TO HUMANS AND DOMESTIC ANIMALS

CAUTIONHarmful if swallowed. Wash thoroughly with soap and water after handling and before eating, drinking, chewing gum, using tobacco or using the toilet. Remove and wash contaminated clothing before reuse. Prolonged or frequently repeated skin contact may cause allergic reactions in some individuals.

PHYSICAL OR CHEMICAL HAZARDSContents under pressure. Do not use or store near heat or open flame. Do not puncture or incinerate container. Exposure to temperatures above 130°F may cause bursting. Do not apply this product around electrical equipment due to the possibility of shock hazard.

FIRST AIDIF SWALLOWED:

Have the product container or label with you when calling a poison control center or doctor, or going for treatment. For information regarding medical emergencies or pesticide incidents, call 1-888-740-8712.

EPA Reg. No. 1021-2569EPA Est. No. 1021-MN-21111-0212

Manufactured by MGK®. ©2012 MGK. All rights reserved.

8810 Tenth Avenue North, Minneapolis, MN 55427

2.5M-0212

Federal regulations prohibit CFC propellants in aerosols

TM

INSECTICIDE WITH PYRETHRINSContains Pyrethrins, A Botanical Insecticide

Provides Rapid Control of Residential, Industrial, andBarn Pests. Excellent Flushing, 8 to 1 Synergist Ratio,Quick Knockdown, Nonaqueous, Highly ActiveSolvent System, Fast Knockdown and KillKILLS and REPELS: Flies, Mosquitoes, Wasps, Gnats,Cockroaches, Ants, Crickets, Spiders, Silverfish,Small Flying Moths, Indianmeal Moths, AngoumoisGrain Moths, Carpet Beetles, Confused FlourBeetles, Sawtoothed Grain Beetles, Granary Weevils,Rice Weevils, Red Flour Beetles, Grain Mites,Bedbugs, Fleas, Barn Flies, Deer Flies, Stable Filesand Horn FliesFOR USE in Homes, Offices, Hotels, Motels, Schools,Hospitals, Nursing Homes, Day-care Centers,Factories, Warehouses, Stores, Supermarkets,Restaurants, Food Handling Establishments,Commercial or Institutional Kitchens, FoodProcessing Plants, Bottling Plants, TransportationEquipment (Automobiles, Buses, Trucks, Trailers,Boats, Ships, Trains, Aircraft (Cargo areas only)),Barns, Stables, Farms, Animal Quarters, Milkrooms,and Poultry HousesCONTAINS NO CFCs OR OTHER OZONE DEPLETINGSUBSTANCES.FEDERAL REGULATIONS PROHIBIT CFC PROPEL-LANTS IN AEROSOLS.

FMC CorporationAgricultural Products Group1735 Market StreetPhiladelphia, PA 19103Net Weight: 17 oz/482 g

11-04-09

EPA Reg. No. 279-3393 EPA Est. No. 9444-LA-1

ACTIVE INGREDIENTS:Pyrethrins .......................................................... 0.50%Piperonyl Butoxide, technical* .......................... 4.00%

OTHER INGREDIENTS ...................................... 95.50%100.00%

*Equivalent to 3.2% (butylcarbityl) (6-propylpiperonyl) ether and 0.8% relatedcompounds.

FLUSHING & CONTACT


CAUTIONSee Back Panel for Additional Precautionary Statements.

PRECAUTIONARY STATEMENTSHazards to Humans & Domestic AnimalsCAUTIONHarmful if swallowed or absorbed through skin. Avoid breathing ofvapors or spray mist. Avoid contact with skin and eyes. In case of con-tact, immediately flush eyes with plenty of water. Obtain medical atten-tion if irritation persists.Do not apply directly to food. Volumetric Treatment of Food Areasand/or Food Handling Establishments: Cover or remove any food andfood processing equipment during application. Do not apply while foodprocessing is underway. After space spraying food processing plants,thoroughly wash all equipment, benches, shelving, etc. where exposedfood will be handled with an effective cleaning compound and rinse withpotable water before use. Volumetric Treatment in Homes: In the home,all food processing surfaces and utensils should be covered duringtreatment or thoroughly washed before use. Before spraying in MedicalCare Areas, remove all patients. After spraying, ventilate area for 2hours before returning patients.Remove pets, birds and cover fish aquariums before spraying.

PHYSICAL OR CHEMICAL HAZARDSFlammable. Contents under pressure. Keep away from heat, sparksand open flames. Do not puncture or incinerate container. Exposure totemperatures above 130°F may cause bursting. Do not spray on plas-tic, painted or varnished surfaces or directly into electronic equipmentsuch as radios, TVs, computers, etc.[For Cylinder Application:] Contents under pressure. Do not use orstore near heat or open flame. Do not puncture or incinerate container.Exposure to temperatures above 130°F may cause bursting.Do not spray on plastic, painted or varnished surfaces or directly intoelectronic equipment such as radios, TVs, computers, etc.FIRST AIDIf Swallowed: Call a poison control center or doctor for treatmentadvice. Have person sip a glass of water if able to swallow. Do notinduce vomiting unless told to do so by the poison control center or doc-tor. Do not give anything by mouth to an unconscious person.If Inhaled: Move person to fresh air. If person is not breathing, call 911or an ambulance, then give artificial respiration, preferably by mouth-to-mouth, if possible. Call a poison control center or doctor for further treat-ment adviceIf on Skin or Clothing: Take off contaminated clothing. Rinse skinimmediately with plenty of water for 15-20 minutes. Call a poison con-trol center or doctor for treatment advice.

Manufactured By:

Return to Index...

If In Eyes: Hold eye open and rinse slowly and gently with water for 15-20 minutes. Remove contact lenses, if present, after the first 5 minutes,then continue rinsing eye. Call a poison control center or doctor fortreatment advice.HOTLINE NUMBER - Have the product container or label with youwhen calling a poison control center or doctor, or going for treatment.For emergency information, call (800) 331-3148.For product information call (800) 321-1FMC (1362).DIRECTIONS FOR USEIt is a violation of Federal law to use this product in a manner inconsis-tent with its labeling.For Cylinder Applications: Use appropriate equipment, with foggingtips and crack & crevice extension tips for voids. Place injection tips intocracks, crevices, holes and small openings. Release approximatelyone-second of product. Repeat as necessary. Several holes may berequired in long-running voids.Applications in Aircraft: This product can be applied to cargo areas ofaircraft only. Do not use in aircraft cabins.FLYING INSECTS: Flies, Mosquitoes, Small Flying Moths, Wasps,Gnats – Calculate cubic feet of space to be treated. Close all doors andwindows. Spray in sweeping motion to all parts of the room. Apply for 2-3 seconds per 1,000 cubic feet of space. Sweep up and destroy falleninsects. Repeat treatment as necessary.CRAWLING INSECTS: Cockroaches, Ants, Spiders, Silverfish -General Volumetric Treatment: Open cabinets and doors in area to betreated. Shut off air conditioners, fans, and close doors and windowsbefore spraying. Spray for 20 seconds per 1,000 cubic feet of space.Direct spray toward areas suspected of harboring insects. Spray intohiding places such as cracks and crevices, behind sinks, cabinets,along baseboards and floors, around drains and plumbing, hittinginsects with spray whenever possible. Keep area closed for 15 minutes.Open and ventilate before reoccupying. Repeat treatment as necessary.FOR COCKROACHES: For best results, spray directly on cockroachesand thoroughly spray all parts of the room suspected of harboring thesepests. Special attention should be paid to cracks, hidden surfaces,under sinks, behind stoves and refrigerators, food storage areas, andwherever these pests are suspected of hiding. Also, spray around door-and windowframes. Repeat as necessary.CRACK & CREVICE APPLICATION: Food Areas and/or Food HandlingEstablishments–Spray in cracks and crevices, using the crack andcrevice nozzle provided. A crack and crevice application may be donein food areas and/or food handling establishments while these facilitiesare in operation by taking extreme care not to contaminate surfaces.FOR SPIDERS AND SILVERFISH: For control of these insects, fre-quent and repeated spraying of baseboards, windows, doorframes,bookcases and storage areas should be made. For best results, spraydirectly on insects.FOR CRICKETS: Spray thoroughly and frequently behind stoves,refrigerators, under cabinets, in food storage areas, and especially inclosets, basements, and other damp areas. For best results, spraydirectly on insects.FOR ANTS: Spray ant trails, nests and points of entry. For initial clean-up, apply for 10-15 seconds per 100 square feet of floor area. Then peri-odically spray as a space treatment for 3-5 seconds per 100 cubic feetof space.FOR INDIANMEAL MOTHS AND ANGOUMOIS GRAIN MOTHS:Close doors and windows. Direct spray into all parts of room especiallyaround stored food product containers, pallets and darkened areas.Spray 7 to 10 seconds for each 1,000 cubic feet of space. Keep areaclosed for 15 minutes following treatment. Repeat application weekly oras needed.FOR CARPET BEETLES: Spray directly on beetles, baseboards, floors,shelves and carpets. Repeat treatment as necessary.FOR CONFUSED FLOUR BEETLES, SAWTOOTHED GRAIN BEE-TLES, GRANARY WEEVILS, RICE WEEVILS, RED FLOUR BEETLES,GRAIN MITES: Spray into cracks and crevices, processing and han-dling equipment, around cartons or containers and other areas wherethese insects tend to congregate. Spray 30 seconds for each 100square feet of surface. Keep area closed for 45 minutes to 1 hour aftertreatment. Repeat application as necessary. Infested stored food prod-ucts in the home should be disposed of.FOR BEDBUGS: Spray mattresses, particularly around tufts andseams. Take beds apart and spray into all joints. Treat baseboards,moldings and floors. Repeat treatment as necessary.FOR FLEAS: Spray sleeping quarters, bedding, floor and floor coveringwhere pets are kept. Repeat as necessary. For best results, use with arecommended pet spray on pets.HOME USE: To kill Cockroaches, Spiders, Silverfish, Wasps, Hornets,Crickets–Spray the insect directly when possible and spray all probablehiding places such as cracks, crevices, baseboards, sinks, cabinets,shelves and under appliances. Repeat as necessary.FOOD PROCESSING PLANT USE: To kill Cockroaches, Spiders,Silverfish, Wasps, Hornets, Crickets–Spray the insect directly whenpossible. Spray all probable hiding places such as cracks, crevices,baseboards, sinks, cabinets, shelves, under appliances, and in food

storage areas. To Kill Flies, Mosquitoes, Gnats, Small Flying Moths –Close all windows and doors. Direct spray upward, spraying for 2-3 sec-onds for 1,000 cubic feet of space. Do not remain in treated areas.Ventilate after treatment.VOLUMETRIC TREATMENT FOR INACCESSIBLE VOIDS (Attics,False Ceilings, Wall and Equipment Voids): For crack and crevice appli-cation, calculate void volume in cubic feet. Treat 20 seconds per 1,000cubic feet. Repeat as necessary.Note, when using this product in an enclosed area, such as milkroom,barn or stable, remove animals before spraying.DAIRY FARM USE: Milking Parlor and Milkroom: Close all windows anddoors. Direct spray upwards, spraying for 2-3 seconds per 1,000 cubicfeet of space. Do not remain in treated areas. Ventilate after treatment.Cover milking utensils and milk to prevent contamination from spray ordead and falling insects.ANIMAL USE: Thoroughly spray entire animal from approximately 2 feetdistance. Do not spray directly toward animal's eyes. Spot treat withers,shoulders, and back where saliva accumulates from head tossing.BEEF CATTLE OPERATIONS: In barns, close all windows and doors.Spray at the rate of 2-3 seconds per 1,000 cubic feet of space. Do notremain in treated area. After 15 minutes, ventilate the area. Repeatapplication as necessary.ANIMAL USE: For animal application, thoroughly spray entire animalfrom approximately 2 feet distance. Do not spray directly toward ani-mal's face or eyes. Repeat application daily or as necessary.STANCHION BARN USE: Walk behind animals and direct spray overbacks, allowing 5 seconds per animal. For most effective results, applyeach morning.HORSE BARNS OR STABLES: In horse and pony barns, close all win-dows and doors. Spray at the rate of 2-3 seconds per 1,000 cubic feetof space. Do not remain in the treated area. After 15 minutes, ventilatethe area. Repeat the application as necessary.ANIMAL USE: For animal application, lightly mist over back of horsesand ponies from a distance of 2 feet. Do not spray directly toward theanimal's face or eyes. Repeat application daily or as necessary.HOG AND SWINE OPERATIONS: In hog houses, close all doors andwindows. Spray at the rate of 2-3 seconds per 1,000 cubic feet of space.Do not remain in treated area. After 15 minutes, ventilate the area.Repeat the application as necessary.SWINE/ANIMAL USE: For animal application, direct spray over back ofhogs and spray for 5 seconds per hog. Do not spray directly towards theanimal's face or eyes. Repeat application daily or as necessary.POULTRY OPERATIONS: In poultry houses, close all windows anddoors. Spray roosts, walls, nests, and cages thoroughly. Spray at therate of 2-3 seconds per 1,000 cubic feet of space. Do not remain intreated areas. After 15 minutes, ventilate the area. Treat daily or as nec-essary.

STORAGE & DISPOSALDo not contaminate water, food or feed by storage or disposal.Storage: Do not store near heat or open flame. Store in cool dry areaaway from children.Disposal: Do not puncture or incinerate. If empty: Place in trash or offerfor recycling if available. If partly filled: Call your local solid wasteagency for disposal instructions.

STEEL

™

NET W

T:18

lbs

(8.2

kg)

KILL

S RA

TS, M

ICE

& M

EADO

W V

OLES

*

KE

EP

OU

T O

F R

EA

CH

OF

CH

ILD

RE

NC

AU

TIO

NSe

e ba

ck p

anel

s fo

r Firs

t Aid

and

add

itiona

l pre

caut

iona

ry s

tate

men

ts.

Kill

s W

arfa

rin

Res

ista

nt N

orw

ay R

ats

®

CONTR

ACA

LL

-WE

AT

HE

R B

LO

X ™

ACTI

VE IN

GRED

IENT

: Br

omad

iolon

e (C

AS #

2877

2-56

-7):

. . .

. . .

. . .

0.00

5%OT

HER

INGR

EDIE

NTS†

: . .

. . .

. . .

. . .

. . .

99.9

95%

† Con

tains

Den

aton

ium B

enzo

ate

TOT

AL

100.

000%

*Not

per

mitt

ed fo

r use

aga

inst

the

follo

win

g sp

ecie

s in

Cal

iforn

ia: C

otto

n ra

t, Ea

ster

n ha

rves

t mou

se, G

olde

n m

ouse

,Po

lyne

sian

rat,

Mea

dow

vol

e, W

hite

-thro

ated

woo

drat

, Sou

ther

n pl

ains

woo

drat

, and

Mex

ican

woo

drat

.

SPEC

IMEN

LAB

EL

Index

587C

B-9

Prod

uct C

ode:

CB40

5109

0415

/09-1

5

DIRE

CTIO

NS FO

R US

EIt i

s a vi

olatio

n of F

eder

al law

to us

e this

prod

uct in

a ma

nner

inco

nsist

ent w

ith its

labe

ling.

READ

THIS

LAB

EL: R

ead t

his en

tire la

bel a

nd fo

llow

all us

e dire

ction

s and

use p

reca

ution

s. U

se on

ly for

sites

, pes

ts,

and a

pplic

ation

meth

ods d

escri

bed o

n this

labe

l.

IMPO

RTAN

T: Do

not e

xpos

e chil

dren

, pets

, or n

ontar

get a

nimals

to ro

denti

cides

. To h

elp to

prev

ent e

xpos

ure:

1. St

ore u

nuse

d pro

duct

out o

f rea

ch of

child

ren a

nd pe

ts.2.

Apply

bait i

n loc

ation

s out

of re

ach o

f chil

dren

, pets

, dom

estic

anim

als an

d non

targe

t wild

life, o

r in ta

mper

-resis

tant

ba

it stat

ions.

Thes

e stat

ions m

ust b

e res

istan

t to de

struc

tion b

y dog

s and

by ch

ildre

n und

er si

x yea

rs of

age,

and m

ust

be

used

in a

mann

er th

at pr

even

ts su

ch ch

ildre

n fro

m re

achin

g into

bait c

ompa

rtmen

ts an

d obta

ining

bait.

If ba

it can

be sh

aken

from

bait

stati

ons w

hen

they a

re lif

ted, u

nits m

ust b

e se

cure

d or

othe

rwise

immo

bilize

d. S

trong

er b

ait

sta

tions

are n

eede

d in a

reas

open

to ho

ofed l

ivesto

ck, ra

ccoo

ns, b

ears,

or ot

her p

otenti

ally d

estru

ctive

anim

als, o

r in

ar

eas p

rone

to va

ndali

sm.

3. Di

spos

e of p

rodu

ct co

ntaine

r and

unus

ed, s

poile

d, or

unco

nsum

ed ba

it as s

pecif

ied on

this

label.

Bait

statio

ns a

re m

anda

tory

for

outd

oor,

abov

e-gro

und

use.

Tamp

er-re

sistan

t bait

stat

ions

must

be u

sed

wher

ever

child

ren,

pets,

non-

targe

t mam

mals,

or bi

rds m

ay ha

ve ac

cess

to th

e bait

plac

emen

t loca

tion.

USE

REST

RICT

IONS

: This

pro

duct

may o

nly b

e us

ed to

contr

ol the

follo

wing

rode

nt pe

sts in

and

aro

und

man-

made

str

uctur

es: H

ouse

mou

se (M

us m

uscu

lus),

Norw

ay ra

t (Ra

ttus

norve

gicus

), Ro

of ra

t (Ra

ttus

rattu

s), C

otton

mou

se

(Per

omys

cus g

ossy

pinus

), Co

tton

rat*

(Sigm

odon

hisp

idus),

Dee

r mou

se (P

erom

yscu

s man

iculat

us),

Easte

rn h

arve

st mo

use*

(Reit

hrod

ontom

ys h

umuli

), Go

lden

mous

e* (O

chro

tomys

nutt

alli),

Polyn

esian

rat*

(Ratt

us e

xulan

s), M

eado

w vo

le* (

Micro

tus p

enns

ylvan

icus),

Whit

e-foo

ted m

ouse

(Pe

romy

scus

leuc

opus

), W

hite-

throa

ted w

oodr

at* (

Neoto

ma

albigu

la), S

outhe

rn pl

ains w

oodr

at* (N

eotom

a micr

opus

), and

Mex

ican w

oodr

at* (N

eotom

a mex

icana

). This

prod

uct m

ust

be u

sed

in an

d wi

thin

100

feet o

f man

-mad

e str

uctur

es co

nstru

cted

in a

mann

er so

as t

o be

vulne

rable

to co

mmen

sal

rode

nt inv

asion

s and

/or to

har

borin

g or

attr

actin

g ro

dent

infes

tation

s. Ex

ample

s of s

uch

struc

tures

inclu

de h

omes

and

oth

er p

erma

nent

or t

empo

rary

resid

ence

s, foo

d pr

oces

sing

facilit

ies,

indus

trial a

nd c

omme

rcial

build

ings,

trash

re

cepta

cles,

agric

ultur

al an

d pu

blic

build

ings,

trans

port

vehic

les (s

hips,

trains

, airc

raft)

, doc

ks a

nd p

ort o

r ter

mina

l bu

ilding

s and

relat

ed st

ructu

res a

roun

d and

asso

ciated

with

thes

e site

s. F

ence

and p

erim

eter b

aiting

, bey

ond 1

00 fe

et fro

m a s

tructu

re as

defin

ed ab

ove,

is pr

ohibi

ted. T

his pr

oduc

t mus

t not

be ap

plied

dire

ctly t

o foo

d or fe

ed cr

ops.

DIRE

CTIO

NS FO

R US

E (C

ontin

ued f

rom

other

pane

l)

Burro

w ba

iting w

ith C

ontra

c All-W

eathe

r Blox

is pr

ohibi

ted.

Do no

t plac

e nea

r or in

side v

entila

tion d

uct o

penin

gs. D

o not

conta

mina

te wa

ter, fo

od, fe

edstu

ffs, fo

od or

feed

hand

ling

equip

ment,

or m

ilk or

mea

t han

dling

equip

ment

or su

rface

s tha

t com

e into

dire

ct co

ntact

with

food.

Whe

n use

d in U

SDA

inspe

cted f

acilit

ies, th

is pr

oduc

t mus

t be a

pplie

d in t

ampe

r-res

istan

t bait

stati

ons.

Do no

t bro

adca

st ba

it. Do

not u

se th

is pr

oduc

t in se

wers.

Do no

t sell

this

prod

uct in

indiv

idual

conta

iners

holdi

ng le

ss th

an 16

poun

ds of

bait.

SELE

CTIO

N OF

TREA

TMEN

T AR

EAS:

Dete

rmine

are

as w

here

rats,

mice

, or m

eado

w vo

les* w

ill mo

st lik

ely fin

d an

d co

nsum

e the

bait

. Ge

nera

lly, th

ese

area

s ar

e alo

ng w

alls,

by g

nawe

d op

ening

s, in

corn

ers

and

conc

ealed

plac

es,

betw

een f

loors

and w

alls,

or in

loca

tions

whe

re ra

ts, m

ice, o

r mea

dow

voles

*, or

their

sign

s hav

e bee

n see

n. Pr

otect

bait

from

rain

and s

now.

Rem

ove a

s muc

h alte

rnati

ve fo

od as

poss

ible.

APPL

ICAT

ION

DIRE

CTIO

NS:

RATS

: Plac

e 3 to

16 ba

it bloc

ks (a

t inter

vals

of 15

to 30

feet)

per p

lacem

ent in

infes

ted ar

eas.

Main

tain a

n unin

terru

pted

supp

ly of

fresh

bait f

or at

leas

t 10 d

ays o

r unti

l sign

s of r

at ac

tivity

ceas

e. MI

CE A

ND M

EADO

W VO

LES*

: Plac

e 1

block

per

plac

emen

t. Spa

ce p

lacem

ents

at 8-

to 1

2-foo

t inter

vals

in inf

ested

ar

eas.

Two b

locks

may

be ne

eded

at po

ints o

f ver

y high

activ

ity. M

aintai

n an

unint

erru

pted s

upply

of fr

esh b

ait fo

r at le

ast 1

5 day

s or u

ntil s

igns o

f mo

use o

r mea

dow

vole*

activ

ity ce

ase.

FOLL

OW-U

P: R

eplac

e co

ntami

nated

or

spoil

ed b

ait i

mmed

iately

. W

earin

g glo

ves,

colle

ct an

d dis

pose

of a

ll dea

d, ex

pose

d an

imals

and

lef

tover

bait.

To pr

even

t rein

festat

ion, li

mit s

ource

s of r

oden

t food

, wate

r, an

d ha

rbor

age

as m

uch

as p

ossib

le. I

f rein

festat

ion d

oes o

ccur,

repe

at tre

atmen

t. W

here

a co

ntinu

ous s

ource

of in

festat

ion is

pres

ent, e

stabli

sh

perm

anen

t bait

stati

ons a

nd re

plenis

h as n

eede

d.

PREC

AUTIO

NARY

STA

TEME

NTS

HAZA

RDS T

O HU

MANS

AND

DOM

ESTIC

ANI

MALS

CAUT

ION:

Har

mful

if sw

allow

ed o

r abs

orbe

d thr

ough

the

skin.

Kee

p aw

ay fr

om ch

ildre

n, do

mesti

c anim

als a

nd p

ets. D

o no

t get

in ey

es, o

n sk

in or

on cl

othing

. Al

l han

dlers

(inclu

ding

appli

cator

s) mu

st we

ar: s

hoes

plus

soc

ks, a

nd

water

proo

f glov

es.

Any p

erso

n wh

o re

trieve

s car

cass

es o

r unu

sed

bait

follow

ing ap

plica

tion o

f this

prod

uct m

ust w

ear g

loves

.

ENVI

RONM

ENTA

L HAZ

ARDS

This

prod

uct is

extre

mely

toxic

to fis

h, bir

ds an

d othe

r wild

life. D

ogs a

nd pr

edato

ry an

d sca

veng

ing m

amma

ls an

d bir

ds m

ight b

e pois

oned

if the

y fee

d upo

n anim

als th

at ha

ve ea

ten th

is ba

it. Do

not a

pply

this p

rodu

ct dir

ectly

to

water

or to

area

s whe

re su

rface

wate

r is pr

esen

t or t

o inte

rtida

l are

as be

low th

e mea

n high

wate

r mar

k. R

unoff

als

o may

be ha

zard

ous t

o aqu

atic o

rgan

isms i

n wate

r adja

cent

to tre

ated a

reas

. Do n

ot co

ntami

nate

water

whe

n dis

posin

g of e

quipm

ent w

ash w

ater o

r rins

ate.

*Not

per

mitte

d fo

r use

aga

inst t

he fo

llowi

ng s

pecie

s in

Califo

rnia:

Cot

ton

rat,

Easte

rn h

arve

st mo

use,

Golde

n mo

use,

Polyn

esian

rat, M

eado

w vo

le, W

hite-t

hroa

ted w

oodr

at, S

outh

ern p

lains

woo

drat,

and M

exica

n woo

drat.

Norw

ay ra

ts, ro

of ra

ts, an

d hou

se m

ice m

ay co

nsum

e a le

thal d

ose i

n one

nigh

t's fe

eding

with

firs

t dea

d rod

ents

appe

aring

four

or fiv

e day

s afte

r feed

ing be

gins.

ACTI

VE IN

GRED

IENT

: Br

omad

iolon

e (C

AS #

2877

2-56

-7):

. . .

. . .

. . .

0.00

5%OT

HER

INGR

EDIE

NTS†

: . .

. . .

. . .

. . .

. . .

99.9

95%

† Con

tains

Den

aton

ium B

enzo

ate

TOT

AL

100.

000%

KEE

P O

UT

OF

REA

CH

OF

CH

ILD

REN

CAU

TIO

N

NET

WEI

GH

T: 1

8 lb

s (8.

2 kg)

See s

ide pa

nels

for F

irst A

id an

d add

itiona

l pre

cauti

onar

y stat

emen

ts.

Kills

War

farin

Res

ista

nt N

orw

ay R

ats

KIL

LS R

ATS

, MIC

E, A

ND

ME

AD

OW

VO

LES

*

®

CONTR

ACA

LL

-WE

AT

HE

R B

LO

X ™

WARR

ANTY

: To

the

exten

t con

sisten

t with

app

licab

le law

, sell

er m

akes

no

warra

nty, e

xpre

ssed

or i

mplie

d, co

ncer

ning t

he us

e of th

is pr

oduc

t othe

r than

indic

ated o

n the

labe

l. Bu

yer a

ssum

es al

l risk

of us

e and

/or ha

ndlin

g of

this m

ateria

l whe

n suc

h use

and/o

r han

dling

is co

ntrar

y to l

abel

instru

ction

s.

EPA

REG.

NO.

1245

5-79

E

PA E

ST. N

O. 12

455-

WI-1

FIRST

AID

HAVE

LABE

L WITH

YOU

WHE

N OB

TAIN

ING

TREA

TMEN

T ADV

ICE

IF SW

ALLO

WED

: •

Call a

poiso

n con

trol c

enter

, doc

tor, o

r 1-8

77-8

54-2

494,

or 1-

800-

858-

7378

** im

media

tely f

or tr

eatm

ent a

dvice

.•

Have

perso

n sip

a glas

s of w

ater if

able

to sw

allow

.•

Do no

t indu

ce vo

mitin

g unle

ss to

ld to

do so

by th

e pois

on co

ntrol

cente

r or d

octor

.IF

ON S

KIN

OR C

LOTH

ING:

• Ta

ke of

f con

tamina

ted cl

othing

. Rins

e skin

imme

diatel

y with

plen

ty of

water

for 1

5–20

minu

tes.

• Ca

ll a po

ison c

ontro

l cen

ter or

docto

r for t

reatm

ent a

dvice

.IF

IN E

YES:

• Ho

ld ey

e ope

n and

rinse

slow

ly an

d gen

tly w

ith w

ater fo

r 15–

20 m

inutes

.•

Remo

ve co

ntact

lense

s, if p

rese

nt, af

ter th

e firs

t 5 m

inutes

, then

conti

nue r

insing

eye.

• Ca

ll a po

ison c

ontro

l cen

ter, d

octor

, or 1

-877

-854

-249

4 imm

ediat

ely fo

r tre

atmen

t adv

ice.

** Al

so ca

ll this

numb

er fo

r infor

matio

n on h

ealth

conc

erns

and p

estic

ide in

ciden

ts.

NOTE

TO P

HYSI

CIAN

If

swall

owed

or a

bsor

bed

throu

gh th

e sk

in, th

is ma

terial

may

redu

ce th

e clo

tting

abilit

y of

the b

lood

and

caus

e ble

eding

. If in

geste

d, ad

minis

ter V

itami

n K1 in

tramu

scula

rly or

orall

y. R

epea

t as n

eces

sary

base

d on m

onito

ring o

f pr

othro

mbin

times

.

TREA

TMEN

T FOR

PET

POI

SONI

NGIf a

nimal

eats

bait,

call v

eterin

arian

at on

ce.

NOTE

TO VE

TERI

NARI

ANAn

ticoa

gulan

t Bro

madio

lone:

For a

nimals

inge

sting

bait

and

/or s

howi

ng p

oison

ing s

igns

(blee

ding

or e

levate

d pr

othro

mbin

times

), giv

e Vita

min K

1. If n

eede

d, ch

eck p

rothr

ombin

times

ever

y 3 da

ys un

til va

lues r

eturn

to no

rmal

(up t

o 30 d

ays).

In se

vere

case

s, blo

od tr

ansfu

sions

may

be ne

eded

.

Manu

factur

ed by

:

3699

Kins

man B

lvd.

Madis

on, W

I 537

04 U

.S.A

.ww

w.be

lllabs

.com

MADE

IN U

SA

STOR

AGE

AND

DISP

OSAL

Do no

t con

tamina

te wa

ter, fo

od or

feed

by st

orag

e or d

ispos

al.Pe

sticid

e Sto

rage

: Stor

e only

in or

igina

l con

taine

r in a

cool,

dry p

lace i

nacc

essib

le to

child

ren a

nd pe

ts. K

eep

conta

iners

close

d and

away

from

othe

r che

mica

ls.Pe

sticid

e Disp

osal:

Was

tes re

sultin

g fro

m the

use o

f this

prod

uct m

ay be

plac

ed in

tras

h or d

elive

red t

o an

appr

oved

was

te dis

posa

l facil

ity.

Cont

ainer

Han

dling

: Non

refill

able

conta

iner.

Do no

t reus

e or r

efill t

his co

ntaine

r. [Pl

astic

:] Of

fer fo

r rec

yclin

g or

reco

nditio

ning;

or pu

nctur

e and

disp

ose o

f in a

sanit

ary l

andfi

ll; or

by in

ciner

ation

. In m

ost s

tates

, bur

ning i

s no

t allo

wed.

User

Safe

ty Re

quire

ment

sFo

llow

manu

factur

er’s

instru

ction

for c

leanin

g/main

tainin

g PPE

. If n

o suc

h ins

tructi

ons f

or w

asha

bles,

use d

eterg

ent

and

hot w

ater.

Keep

and

was

h PP

E se

para

tely f

rom

other

laun

dry.

Rem

ove

PPE

imme

diatel

y afte

r han

dling

this

prod

uct.

Was

h the

outsi

de of

glov

es be

fore r

emov

ing. A

s soo

n as p

ossib

le, w

ash h

ands

thor

ough

ly aft

er ap

plying

bait

and b

efore

eatin

g, dr

inking

, che

wing

gum,

using

toba

cco o

r usin

g the

toile

t and

chan

ge in

to cle

an cl

othing

.

SPEC

IMEN

LAB

EL

Mini-PelletsONE LAST MEAL FOR SLUGS & SNAILS

EFFECTIVE DEADLINE M-Ps excel at attracting and destroying slugs and snails. LONG LASTING Remains effective after rain and watering. DEADLINE M-Ps are not easily dissipated by water. IMPROVED COVERAGE Five times the number of bait particles compared to regular size pellets.

ACTIVE INGREDIENT: Metaldehyde (2,4,6,8-Tetramethyl- 1,3,5,7-Tetraoxycyclo-octane) ............................. 4.0%

INERT INGREDIENTS: ...................................................................................................... 96.0% TOTAL: ............................................................................................................................... 100.0%

KEEP OUT OF REACH OF CHILDREN CAUTION - CUIDADO

Si usted no entiende la etiqueta, busque a alguien para que se la explique a usted en detaile. (If you do not understand this label, find someone to explain it to you in detail.)

FIRST AID If swallowed: • Call a poison control center or doctor immediately for treatment advice.

• Have a person sip a glass of water if able to swallow.• Do not induce vomiting unless told to by a poison control center or doctor.• Do not give anything by mouth to an unconscious person.

If in eyes: • Hold eye open and rinse slowly and gently with water for 15-20 minutes.• Remove contact lenses, if present, after the first 5 minutes, then continue

rinsing eye.• Call a poison control center or doctor for treatment advice.

If on skin or clothing:

• Take off contaminated clothing.• Rinse skin immediately with plenty of water for 15-20 minutes.• Call a poison control center or doctor for treatment advice.

If inhaled: • Move person to fresh air.• If person is not breathing, call 911 or ambulance, then give artificial

respiration, preferable mouth-to-mouth, if possible.• Call a poison control center or doctor for further treatment advice.

SEE SIDE/BACK PANEL FOR ADDITIONAL PRECAUTIONARY STATEMENTS AND DIRECTIONS FOR USE. EPA Reg. No. 5481-507 Net Weight: EPA Est. No. ________ As Marked on Container

4100 E. Washington Blvd. Los Angeles, CA 90023 U.S.A

1-888-462-6822

11632-20150305 Page 1 of 8

Return to Index...

EMERGENCY INFORMATION

Seek medical care as soon as possible after exposure. For incidents involving animals, seek veterinary care as soon as possible after exposure. Have the product container or label with you when calling a poison control center or doctor or veterinarian, or going for treatment.

FOR THE FOLLOWING EMERGENCIES, PHONE 24 HOURS A DAY: For Medical Emergencies phone:........................................................................................1-888-681-4261 For Transportation Emergencies, including spill, leak or fire, phone: CHEMTREC….....1-800-424-9300 For Product Use Information phone : AMVAC………………......……......................…..1-888-462-6822 Metaldehyde is a systemic toxin. There is no antidote. The following instructions are not intended for laypeople. There is no home treatment. Exposed individuals and animals should receive emergency care as quickly as possible. NOTE TO PHYSICIAN: Dust inhalation is usual route of accidental exposure; the product is rarely ingested. Treatment is symptomatic and supportive. Monitor severe exposures closely: seizures, electrolyte imbalances, acidosis, dehydration, and increased body temperature have been reported. NOTE TO VETERINARIAN: Animals typically are exposed via ingestion. Treatment is symptomatic and supportive. If significant ingestion is suspected, and the animal is asymptomatic, consider induction of emesis or gastric lavage and administration of activated charcoal, cathartic and enema to limit absorption. Monitor asymptomatic and symptomatic animals closely. Treat seizures, electrolyte imbalances, acidosis, dehydration, and increased body temperature. Monitor liver function post recovery.

PRECAUTIONARY STATEMENTS Hazards to Humans & Domestic Animals IMPORTANT: This product can be harmful to children and fatal to domestic animals when ingested. Children and dogs may be attracted to the product. Application of this product is prohibited unless children and domestic animals can be excluded from the treated area from the start of the application until applied material is no longer visible. CAUTION: Harmful if swallowed. Harmful if absorbed through skin. Harmful if inhaled. Causes moderate eye irritation. Avoid contact with skin, eyes or clothing. Avoid breathing dust. Personal Protective Equipment (PPE) Mixers, loaders, applicators and other handlers must wear: • Long sleeved shirt and long pants • Shoes plus socks • Chemical resistant gloves (such as or made out of any waterproof material, selection category A) User Safety Requirements Follow manufacturer’s instructions for cleaning/maintaining PPE. If no such instructions for washables exist, use detergent and hot water. Keep and wash PPE separately from other laundry. Discard clothing and other absorbent materials that have been drenched or heavily contaminated with this product’s concentrate. Do not reuse them.

11632-20150305 Page 2 of 8

Engineering Controls When handlers use closed systems or enclosed cabs in a manner that meets the requirements listed in the Worker Protection Standard (WPS) for agricultural pesticides [(CFR 40 170.240 (d) (4-6)], the handler PPE requirements may be reduced or modified as specified in the WPS.

USER SAFETY RECOMMENDATIONS Users should: • Wash hands before eating, drinking, chewing gum, using tobacco, or using the toilet. • Remove clothing/PPE immediately if pesticide gets inside. Then wash thoroughly and put on clean

clothing. • Remove PPE immediately after handling this product. • Wash the outside of gloves before removing. As soon as possible, wash thoroughly and change into

clean clothing. ENVIRONMENTAL HAZARDS This pesticide is toxic to mollusks (e.g., clams, oysters, scallops, mussels). Do not apply directly to water, to areas where surface water is present, or to intertidal areas below the mean high water mark. Drift and runoff may be hazardous to aquatic organisms in water adjacent to treated areas. Do not contaminate water when disposing of equipment wash waters or rinsate. This pesticide is toxic to birds and mammals. Granules on soil surface may be hazardous to terrestrial wildlife. Cover or collect any such materials spilled during loading.

DIRECTIONS FOR USE It is a violation of Federal Law to use this product in a manner inconsistent with its labeling. For any requirements specific to your state or tribe, consult the agency responsible for pesticide regulation. Do not apply this product in a way that will contact workers or other persons, either directly or through drift. Only protected handlers may be in the area during application. This product is intended solely for use on agricultural crops grown for commercial or research purposes, and in State and/or Federal invasive mollusk eradication operations. This product may not be applied to residential sites (i.e., in yards, gardens, around homes and apartments) and other sites such as the exterior areas around schools and daycare facilities, and athletic fields, playgrounds, parks, recreation areas, etc. Broadcast applications and applications of this product directed to plant parts are prohibited except to grass grown for seed, taro, corn, soybean, and as specified for use in State and/or Federal invasive mollusk eradication operations.

11632-20150305 Page 3 of 8

AGRICULTURAL USE REQUIREMENTS

Use this product only in accordance with its labeling and with the Worker Protection Standard, 40 CFR Part 170. This standard contains requirements for the protection of agricultural workers on farms, forests, nurseries, greenhouses and handlers of agricultural pesticides. It contains requirements for training, decontamination, notification and emergency assistance. It also contains specific instructions and exceptions pertaining to the statements on this label about personal protective equipment (PPE), and restricted entry interval. The requirements in this box only apply to users of this product that are covered by the Worker Protection Standard. Do not enter or allow worker entry into treated areas during the restricted entry interval (REI) of 12 hours. Exception: if the product is soil-injected or soil-incorporated, the Worker Protection Standard, under certain circumstances, allow workers to enter the treated areas without restriction if there will be no contact with anything that has been treated. PPE required for early entry to treated areas that is permitted under the Worker Protection Standard and that involves contact with anything that has been treated, such as plants, soil or water, is: • Coveralls • Shoes plus socks • Chemical-resistant gloves made of any waterproof material

For State &/or Federal Invasive Mollusk Eradication Operations This product may be used only on the following use-sites in response to State and/or Federal invasive mollusk eradication operations.

Broadcast applications of this product may be made to the following use-sites for State and/or Federal invasive mollusk eradication operations: fallow land; barrier strips; uncultivated non-agricultural areas; recreational areas; non-food or non-feed brush; weed or dense vegetative areas; railroad, pipeline, highway, power and telephone rights of way and roadsides; guardrails and fences; lumberyards; storage areas; seaports; industrial facility sites, including yards and walkways around industrial buildings, parking areas, parks, golf courses, other public areas; and airport and similar industrial non-crop areas.

This product may be applied for State and/or Federal invasive mollusk eradication operations at an individual application rate of no more than 2 lb. a.i./A (50 lbs Deadline M-Ps per acre) and at no more than six applications/year.

11632-20150305 Page 4 of 8

RESTRICTIONS

• This product is intended solely for use on agricultural crops grown for commercial or research purposes, and in State and/or Federal invasive mollusk eradication operations.

• This product may not be applied to residential sites (i.e., in yards, gardens, around homes and apartments) and other sites such as the exterior areas around schools and daycare facilities, and athletic fields, playgrounds, parks, recreation areas, etc.

• Wide area broadcast applications and applications of this product directed to plant parts are prohibited except to grass grown for seed, taro, corn and soybean and as specified for use in State and/or Federal invasive mollusk eradication operations.

• Do not allow bait pellets to come in contact with plant parts except to grass grown for seed, taro, corn, soybean, and as specified for use in State and/or Federal invasive mollusk eradication operations.

• Use only as a baiting treatment to be applied directly to the soil area beneath listed plants except to grass grown for seed, taro, corn, soybean and as specified for use in State and/or Federal invasive mollusk eradication operations..

• Read entire label before using. • Use as band treatment between rows except to grass grown for seed, taro, corn, soybean and as

specified for use in State and/or Federal invasive mollusk eradication operations.. • Do not re-water for 48 hours after application. • Apply any time of day, but evening applications are preferred. • Do not use in or around Hanalei, Kaua’i (USFW Refuge)

APPLICATIONS Apply as a soil surface treatment. Use a band treatment between the plant rows. Apply around the crops listed below to protect from slugs and snails.

Conversion table for application of product to various size areas

5 – 12 Pellets / sq. ft. = 3.6 – 7.2 oz / 1000 sq. ft. = ½ - 1 cup / 1000 sq. ft. = 1 – 2 lb. / 4400 sq. ft. =10 – 20 lbs. / acre

Apply this product in areas likely to be infested at the beginning of the planting season before damage occurs and during periods of damp weather. The maximum number of applications allowed per season are listed below with each crop. For best results, apply in evening. Especially beneficial if applied following rain or watering since slugs and snails will not crawl over dry soil. Apply every 3 to 4 weeks during growing season, or as needed. Prior experience has shown most plants are not sensitive to Deadline M-Ps. However, for extremely tender plants such as orchids, it is suggested to do a small test application to determine any plant sensitivity before making applications to plants. For use on ornamentals, artichokes, blueberries, caneberries, strawberries, lettuce, cole crops and listed leafy greens, mint, and tomatoes apply in a band, between rows and/or directed towards base of the plants, by hand or with commercial application equipment designed for banded application of granular products.

11632-20150305 Page 5 of 8

For corn and soybeans, broadcast or ground directed applications are allowed. For use on citrus, apply in a band under tree canopy, by hand or with commercial application equipment designed for banded application of granular products.

Crop

Maximum Single Application Rate (lbs/Product/A)

Total number of applications per season

Re-application Interval (days)

Preharvest Interval

Artichokes (Perennial) 25 6 18 0 Artichokes (Annual) 25 2 18 0 Citrus 25 6 14 0 Tomatoes 25 3 14 0 Tomatoes, Lettuce, Cole Crops, and the following Leafy Greens (broccoli, Brussels sprouts, cabbage, cauliflower, cavalo, broccolo, collards, kale, kohlrabi, mizuna, mustard greens, spinach, rape greens). 25 3 14 0 Berries1 20 3 14 0 Strawberries 25 3 14 0 Ornamental Plants2 25 6 21 0 Prickly Pear Cactus 20 3 30 0 Grass (Forage and Hay) 20 4 14 21 Mint (Peppermint, Spearmint, and their Oils) 25 4 21 1 Celery, Rhubarb, Swiss chard, Chinese Celery, Celtuce, Cardoon, and Florence Fennel 25 4 21 1 1Caneberries (bingleberry; raspberry, red and black; wild raspberry; blackberry; loganberry; boysenberry, dewberry; lowberry; marionberry; olallieberry; youngberry; Bushberries (aronia berry; blueberry; buffalo currant; Chilean guava; currant; black and red; elderberry; European barberry; gooseberry; cranberry; honeysuckle; huckleberry; jostaberry; juneberry; lingonberry; salal; sea buckthorn; Berry - low growing (bearberry; bilberry; blueberry; cloudberry; cranberry; muntries; partridgeberry). 2Including ornamentals in greenhouses, hoophouses, and other indoor ornamentals production facilities, as well as outdoor commercial production of ornamental plants.

11632-20150305 Page 6 of 8

The uses listed below allow broadcast application. Crop Growth

Stage1 Maximum Single Application Rate (lbs/Product/A)

Total number of applications per season3


Preharvest Interval

Application Information

Corn (field) Up to V8 25 3 7 0 Broadcast or Ground directed

Corn (field) V-8 - VT 25 3 7 0 Ground directed only

Soybean2 Up to V4 10 3 7 0 Broadcast or Ground directed

Soybean2 V4-R1 10 3 7 0 Ground directed only

1Growth stages are according to the Iowa State University Crop Guides: Corn - http://www.agronext.iastate.edu/corn/docs/corn-field-guide.pdf. Soybeans - http://extension.agron.iastate.edu/soybean/production_growthstages.html 2Only for use in the following states: Alabama, Arkansas, Connecticut, Delaware, Georgia, Louisiana, Maine, Maryland, Massachusetts, Mississippi, North Carolina, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, South Carolina, Tennessee, Vermont, Virginia. Livestock may not graze in the treated fields. Applications must be completed prior to pod formation. 3The maximum number of application per crop per season is 3.

Crop

Maximum Single Application Rate (lbs/Product/A)

Total number of applications per season


Preharvest Interval

Grass (grown for seed) 20 4 21 21 Taro (wetland)* 1 25 7 35 7 1Broadcast application to be made under flooded conditions only. Prior to bait application, stop the water flow into and out of the lo’i (paddies) to be treated; water level should be high enough such that apple snails don’t estivate. Apply the bait and hold/impound the water for a minimum of 3 days before allowing water to exit the lo’i. Do not apply more than one application per held/impounded water. If the water level in the lo’i becomes too low within the 3 day holding period (due to faster percolation of water through the soil), such that apple snails begin to estivate, allow additional water into the lo’i. *Not for use on Taro in California.

11632-20150305 Page 7 of 8

STORAGE AND DISPOSAL Do not contaminate water, food, or feed by storage and disposal. Pesticide Storage: This product can be harmful to children and fatal to dogs and other domestic animals if ingested. Dogs have been known to ingest metaldehyde after opening or tearing the packaging. Store this product in its original packaging, in a cool, secure location, and out of reach of children or pets. Pesticide Disposal: To avoid wastes, use all material in this container by application according to label directions. If wastes cannot be avoided, offer remaining product to a waste disposal facility or pesticide disposal program (often such programs are run by state or local governments or by industry). Container Disposal: Nonrefillable container. Do not reuse or refill this container. Completely empty bag into application equipment. When completely empty, offer for recycling, if available or then dispose of empty bag in a sanitary landfill, or by incineration.

LIMITED WARRANTY AND DISCLAIMER The manufacturer warrants (a) that this product conforms to the chemical description on the label; (b) that this product is reasonably fit for the purposes set forth in the directions for use, subject to the inherent risks referred to herein, when it is used in accordance with such directions; and (c) that the directions, warnings, and other statements on this label are based upon responsible experts' evaluations of reasonable tests of effectiveness, of toxicity to laboratory animals and to plants and residues on food crops, and upon reports of field experience. Tests have not been made on all varieties of food crops and plants, or in all states or under all conditions.

THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE SET FORTH HEREIN. TO THE EXTENT CONSISTENT WITH APPLICABLE LAW THE MANUFACTURER NEITHER MAKES NOR INTENDS, NOR DOES IT AUTHORIZE ANY AGENT OR REPRESENTATIVE, TO MAKE ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, AND IT EXPRESSLY EXCLUDES AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY OF FITNESS FOR A PARTICULAR PURPOSE, OR ANY WARRANTY OF QUALITY OR PERFORMANCE. THIS WARRANTY DOES NOT EXTEND TO, AND THE BUYER SHALL BE SOLELY RESPONSIBLE FOR, ANY AND ALL LOSS OR DAMAGE WHICH RESULTS FROM THE USE OF THIS PRODUCT IN ANY MANNER WHICH IS INCONSISTENT WITH THE LABEL DIRECTIONS, WARNINGS OR CAUTIONS.

TO THE EXTENT CONSISTENT WITH APPLICABLE LAW BUYER'S EXCLUSIVE REMEDY AND MANUFACTURER'S OR SELLER'S EXCLUSIVE LIABILITY FOR ANY AND ALL CLAIMS, LOSSES, DAMAGES, OR INJURIES RESULTING FROM THE USE OR HANDLING OF THIS PRODUCT, WHETHER OR NOT BASED IN CONTRACT, NEGLIGENCE, STRICT LIABILITY IN TORT OR OTHERWISE, SHALL BE LIMITED, AT THE MANUFACTURER'S OPTION, TO REPLACEMENT OF, OR THE REPAYMENT OF THE PURCHASE PRICE FOR, THE QUANTITY OF PRODUCT WITH RESPECT TO WHICH DAMAGES ARE CLAIMED. TO THE EXTENT CONSISTENT WITH APPLICABLE LAW MANUFACTURER OR SELLER SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OR HANDLING OF THIS PRODUCT. AMVAC offers this product, and Buyer accepts it, subject to the foregoing Limited Warranty which may be varied only by agreement in writing signed by an authorized representative of AMVAC. © 2014 AMVAC Chemical Corporation. All Rights Reserved. AMVAC and the BEAKER logo are trademarks, registered in the U.S. and some other countries, of AMVAC Chemical Corporation. DEADLINE is a trademark of Deahinder LLC, registered in the U.S. and some other countries, and is used under license. CHEMTREC is a trademark of American Chemistry Council, Inc. AMVAC Chemical Corporation 4100 E. Washington Blvd. Los Angeles, CA 90023 U.S.A. 1-888-462-6822

11632-20150305 Page 8 of 8

1

2.5"

4.5"

INSECTICIDE

0419107104494104F 141014AV4

Net Weight

1 Pound

Ants • Bed Bugs • Wasps

• PROVIDES QUICK CONTROL OF ANTS, BEES, COCKROACHES, FLEAS, SILVERFISH, TICKS, AND NUMEROUS STORED PRODUCT PESTS.

• KILLS CRAWLING INSECTS UP TO 8 MONTHS WHEN LEFT UNDISTURBED.

• FOR USE INDOORS AND OUTDOORS.• DOES NOT CLUMP OR ABSORB

MOISTURE.• NON-STAINING AND ODORLESS.ACTIVE INGREDIENT:Deltamethrin.................................. 0.05%OTHER INGREDIENTS ....... 99.95%TOTAL: ................................... 100.00%EPA Reg. No. 432-772

KEEP OUT OF REACH OF CHILDRENCAUTION

DeltaDust 1 lb 04494104F 141014AV4 ETL 042715:DeltaDust 1 lb 04494104F 141014AV4 ETL 042715 4/27/15 2:39 PM Page 1

Rrn to Re

Return to Index

Return to Index.....

2

2.5"

4.5"

PRECAUTIONARY STATEMENTSHAZARDS TO HUMANS & DOMESTIC ANIMALSCAUTIONMay be harmful if absorbed through skin. Avoid contact with skin,eyes, or clothing. Wash thoroughly with soap and water after han-dling.ENVIRONMENTAL HAZARDSThis product is extremely toxic to fish and aquatic invertebrates.Use with care when applying in areas adjacent to any body ofwater. To protect the environment, do not allow pesticide to enteror run off into storm drains, drainage ditches, gutters, or surfacewaters. Applying this product in calm weather when rain is notpredicted for the next 24 hours will help to ensure that wind orrain does not blow or wash pesticide off the treatment area.

DIRECTIONS FOR USEIt is a violation of Federal Law to use this product in a man-ner inconsistent with its labeling. IMPORTANT: Read the en-

tire Directions for Use, Precautions and Disclaimer ofWarranties before using this product.

Containers larger than one pound may not be used or stored infood handling establishments.Not for use on plants being grown for sale or other commercialuse, or for commercial seed production, or for research purposes.For use on plants intended for aesthetic purposes or climatic mod-ification and being grown in interior plantscapes, ornamental gar-dens, parks, or on golf courses, or lawns and grounds.DeltaDust® Insecticide is a ready-to-use insecticide dust whichexhibits effective knockdown and residual control against the pestslisted when used according to label directions.

FIRST AIDIf on skin:

• Wash with plenty of soap and water. Get medicalattention if irritation persists.

In case of medical emergencies or health and safety inquiries orin case of fire, leaking or damage containers, call 1-800-334-7577.

For MEDICAL and TRANSPORTATION Emergencies ONLY Call24 Hours A Day 1-800-334-7577

For PRODUCT USE Information Call 1-800-331-2867

PARA EL USUARIO: Si usted no lee inglés, no use este producto hastaque le hayan explicado completamente las instrucciones en la eti-

queta. (TO THE USER: If you cannot read English, do not use thisproduct until the label has been fully explained to you.)


3

2.5"

4.5"

APPLICATION RESTRICTIONSDo not water the treated area to the point of run-off.Do not make applications during rain.Do not apply directly to sewers or drains, or to any area like agutter where drainage to sewers, storm drains, water bodies,or aquatic habitat can occur, except as directed by this label.DeltaDust Insecticide can be used for residual pest control inand on buildings and structures and their immediate surround-ings. Do not use in aircraft cabins. Permitted areas of use in-clude:

*aircraft*animal quarters/kennels*apartment buildings*bakeries*breweries*buses*canneries*cafeterias*dairies*food/feed manufacturing,processing and service es-tablishments

*greenhouses (non-commer-cial)

*grocery stores and super-markets

*hospitals*hotels/motels*houses*industrial buildings and in-stallations

*laboratories

*mausoleums*meat slaughtering andpacking plants

*mobile homes and recre-ational vehicles

*nursing homes/day carecenters

*rail cars*restaurants*schools*sewers and undergroundtunnels

*stores and institutions*supermarkets*telecommunication con-duits

*theaters*trucks and trailers*utility vaults and conduits*vessels*warehouses*zoos

DeltaDust Insecticide is intended for applications with hand orpower duster (Actisol® DPA or similar equipment), with a paintbrush or by other suitable means, to hiding and runway areasand other places where insects are found. In living areas, makeapplications in such a manner as to avoid depositions on ex-posed surfaces or introducing the material into the air. In thehome, all food processing surfaces and utensils should be cov-ered during treatment or thoroughly washed before use. Exposedfood should be covered or removed. To apply insecticide directly into cracks and crevices, use a bul-bous duster or other suitable equipment. Apply lightly and uni-formly to infested area. Pay particular attention to cracks andcrevices; service ducts; false floors and ceilings; wall voids;around electrical and telephone fittings and equipment; around


4

2.5"

4.5"

water and sewer pipes; under and behind cabinets, refrigerators,and sinks; around windows and door frames; along baseboards;in attics and crawl spaces. The amount to be applied will varywith the site but should usually be in the range of 2 - 3 gramsof DeltaDust Insecticide per square yard (or 0.5 lbs per 1000square feet).

INDOOR USEFOOD/FEED HANDLING ESTABLISHMENTAPPLICATIONSDeltaDust Insecticide applications are permitted in bothfood/feed and non-food areas of food/feed handling establish-ments as a general surface, spot, or crack and crevice treatment.Food/feed handling establishments are defined as places otherthan private residences in which exposed food/feed is held,processed, prepared, or served. Included also are areas for re-ceiving, storing, packing (canning, bottling, wrapping, boxing),preparing, edible waste storage, and enclosed processing sys-tems (mills, dairies, edible oils, syrups) of food. Serving areaswhere food is exposed and the facility is in operation are alsoconsidered food areas.Non-Food/Non-Feed Areas: Examples of non-food/non-feedareas include garbage rooms, lavatories, floor drains (to sewers),entries and vestibules, offices, locker rooms, machine rooms,boiler rooms, mop closets, and storage (after packaging, canningor bottling).General Surface Application: Do not apply as a general surfaceapplication in the food/feed handling areas of the facility, whenthe facility is in operation or foods are exposed. Do not apply di-rectly to food products. Cover or remove all food processingand/or handling equipment during application. After applicationin food processing plants, bakeries, cafeterias, and similar fa-cilities, wash all equipment, benches, shelving, and other sur-faces which food will contact. Clean food handling or processingequipment and thoroughly rinse with clean, fresh water.Spot, Crack and Crevice Application: Spot and/or Crevice ap-plications may be made while the facility is in operation providedexposed food is covered or removed from area being treatedprior to application. Do not apply directly to food or food handlingsurfaces. DeltaDust Insecticide may also be applied as a voidtreatment using suitable equipment, as mentioned above, in-cluding Actisol DPA equipment. Be sure to thoroughly treat serv-ice ducts, false floors and ceilings, wall voids, attics, and crawlspaces. The amount of dust to be applied will vary with the sitebut should usually be in the range of 2 - 3 grams per squareyard (or 0.5 lbs per 1000 square feet). Dust applications shouldbe made in a manner to avoid deposits in exposed surfaces, in-troducing the material in the air.


5

2.5"

4.5"

ANTS, BOXELDER BUGS, COCKROACHES (INCLUDING BOTHRESISTANT AND NON-RESISTANT STRAINS), CRICKETS,FLEAS, FIREBRATS, AND SILVERFISH: Apply DeltaDust Insec-ticide thoroughly to all areas where these pests crawl and hide,especially in those areas described above. For ants, apply to anttrails, around doors and windows, and other places where antsenter premises.TERMITES, CARPENTER ANTS, AND CARPENTER BEES: Applyto voids or channels in damaged wooden members of a struc-ture; to cracks, spaces, or bearing joints between wooden mem-bers of a structure; or between such members and thefoundation; and in locations vulnerable to termite attack. Drillingmay be necessary prior to applying DeltaDust Insecticide inthese locations, but it must be recognized that such drilling andtreating of timber in a particular location may not result in com-plete coverage of infested and vulnerable voids or galleries.Drilling directly overhead with subsequent application ofDeltaDust Insecticide should be avoided. DeltaDust Insecticidecan be applied in attics and crawl spaces to prevent entry ofdrywood and formosan termites at a rate of 0.5 lb per 1000square feet of floor area. In these treatments, all vents and blow-ers should be closed. Inspect at 6 months and one year to insurethat colony has been killed. Retreat if necessary. For subter-ranean termites the purpose of such applications of DeltaDustInsecticide is to kill workers or winged forms which may be pres-ent in the treated channels at the time of treatment. For activetermite infestations get a professional termite inspection. Suchapplications are not a substitute for mechanical alteration, soiltreatment or foundation treatment but merely a supplement. Thissupplemental treatment can be particularly supportive of newconstruction.CENTIPEDES, GROUND BEETLES, MILLIPEDES, SCORPIONS,SPIDERS, AND SOWBUGS: Apply DeltaDust Insecticide alongand behind baseboards, to window and door frames, corners,pipes, storage locations, attics, crawl spaces, and other areaswhere these pests may enter or crawl.WASPS AND BEES: It is generally advisable to treat wasp andbee nests in the evening when insects are less active and havereturned to the nest. Wear protective clothing if deemed neces-sary to avoid stings. Using hand or power duster (Actisol® orsimilar equipment) or other suitable means, with extension tubesif necessary, thoroughly dust nest, entrance, and surroundingareas where insects alight. Nests in wall voids can be locatedby listening with your ear against the wall. Drill a hole in the area,blow dust in and reseal. For ground wasps, dust entrance andsurrounding areas. For best results check nests carefully one ortwo days after treatment to ensure complete kill, then remove


6

2.5"

4.5"

and destroy nest to prevent emergence of newly-hatched in-sects. If removal is not feasible, retreat the nest, if necessary.Do not use this product to treat overhead nests.WEBBING CLOTHES MOTHS: Use DeltaDust Insecticide as acrack and crevice treatment in closets and other storage areaswhere these pests are found. This is an adjunct treatment andwill not control moth larvae already on the clothes. DO NOT applythis product directly to clothing.CARPET BEETLES (BLACK, FURNITURE, COMMON, AND VAR-IED): Dust where these insects are found, for example: on andunder edges of floor coverings, around baseboards, under rugsand furniture, and in closets. In residential areas do not apply asa broadcast application to floors or floor coverings.BED BUGS: Apply DeltaDust Insecticide thoroughly to all areaswhere these pests are typically found including: folds and tuftsof mattresses, coils or springs, cracks, and hollow posts of bed-frames, upholstery of chairs and sofas, picture frame moldingsand all cracks and crevices in the room should be treated. Allowpowder to remain in contact with folds and tufts of mattresses,chair and sofa upholstery for 4 - 6 hours, then thoroughly vac-uum these treated areas, dispose of vacuum bag and place cleanlinens on bed. Also vacuum treated areas that will come into di-rect contact with humans and pets.STORED PANTRY & PRODUCT PESTS: To aid in the control ofthe exposed stages of:

cadellescheese mitescigarette beetlesconfused flour beetlesdark meal wormsdermestidsdrugstore beetlesgrain mitesgranary weevilslesser grain borerslesser mealworms

merchant grain beetlesred flour beetlesrice weevilsrusty grain beetlessaw-toothed grain beetlesspider beetlestobacco mothsyellow meal wormswarehouse moths indian meal mediterranean flour

FOOD PROCESSING PESTSSame crawling & flying pests as in pantry & stored product pestsand Fruit flies, Phorid flies, and Sciarid flies.Clean up waste materials, dust, dirt, and other debris. Thoroughlytreat floors, walls, and other surfaces in storage and handlingareas. Apply dust in cracks and crevices, behind and under cup-boards, and other difficult to reach areas where insects may


7

2.5"

4.5"

hide. DO NOT apply directly on food/feed, utensils or on areaswhere food/feed is stored.ORNAMENTAL PLANT PESTSFor the control of:

SHRUBS AND ORNAMENTALS: Apply when insects or theirdamage first appear and repeat at weekly intervals or as nec-essary. Apply 8 ounces per 1000 square feet; or thoroughly applyto place a thin layer of dust on both upper and lower sides ofleaves, stems, and flowers.ROSES, PETUNIAS, CHRYSANTHEMUMS, GERANIUMS, CAR-NATIONS, AND OTHER RELATED FLOWERS: To control manyleaf and flower chewing insects, apply as soon as the insect ap-pears and repeat at 7 day intervals or as long as insects continueto appear. Apply a thin layer of dust on both upper and lowersides of leaves, stems, and flowers.OUTDOOR USEPERIMETER TREATMENT: Use DeltaDust Insecticide as a resid-ual treatment for control of ants, bees, centipedes, cock-roaches, crickets, firebrats, fleas, ground beetles,millipedes, scorpions, silverfish, slugs, sowbugs, spiders,ticks, and wasps. Make a residual treatment around windowsand doors, porches, screens, eaves, patios, garages, under stair-ways, in crawl spaces, and other areas where pests hide. To helpprevent the invasion of buildings and structures by these pests,apply thoroughly and uniformly to the foundation and crawlspaces where pests are active and may find entrance. SEWER TREATMENT: Cockroach infestations in sanitary sewersmay be treated with DeltaDust Insecticide to provide quickknockdown and short-term population suppression. When treat-ing sewers, one manhole per 200 linear feet should be treated.Treatments are made by removing the manhole cover and re-

aphidsbeet armywormsblister beetlesboxelder bugscertain leafminers (Boxwood, Holly, Oak,

Spruce Needle)

elm leaf beetlesflea beetlesJapanese beetlesleafhoppers

leafrollersorange tortrixperiodical cicadasplant bugsrose chafersrose midgesrose slugstent caterpillarsthripsweevils


8

2.5"

4.5"

placing with a disc of plywood bored to receive the typical flex-ible hose from portable or truck-mounted ventilating equipment.Apply 1 - 2 ounces of dust into the ventilating air to be dispersedquickly and thoroughly through the system.TELECOMMUNICATION TREATMENT: Apply DeltaDust Insecti-cide into telecommunication conduits, cracks and crevices, junc-tion boxes, etc. using suitable application equipment (such asActisol DPA Duster, or other types of application equipment ca-pable of applying the proper amount). The amount of DeltaDustInsecticide to be applied will vary, but should usually be approx-imately 1 gram of dust per cubic foot of conduit. To calculate cubicfeet, use the following equation: (π x radius2 of the conduit x lengthof the conduit. NOTE: radius = one-half the diameter. Example:500 linear feet of a 4” (12” = 1 foot; therefore, 0.33 ft) conduit =3.14 x (0.17 ft x 0.17 ft) x 500 ft = 45.39 cubic feet. DeltaDustInsecticide can be used in areas showing signs of active termiteinfestations, such as underground telecommunication cable con-duits, electrical cable conduits, junction boxes, and manholes.Apply dust through suitable application equipment (such as theActisol DPA Duster, that is capable of delivering particles sus-pended in a low pressure air system). Applications should bemade from both ends of a run of open conduit in cases wherebreakdown in the conduit is suspected. DeltaDust Insecticide canalso be applied directly to the interior of the conduits after cableshave been installed. Apply at the rate of 1 gram of dust per cubicfoot of conduit using equipment (i.e., Actisol DPA Duster) that iscapable of delivering particles suspended in a low pressure airsystem.FIRE ANTS: Apply dust with a shaker can. Thoroughly apply toadequately cover mound and around the perimeter (18” fromthe outer edge of the mound). A second treatment may be nec-essary if complete control is not obtained. DO NOT DISTURB THEMOUND PRIOR TO APPLICATION. If possible, treat all colonies inthe vicinity. Also, treat colonies which have not yet constructeda mound.FLEAS AND TICKS IN RODENT BURROWS: To control fleas andticks in and around rodent burrows around homes and otherbuildings, apply DeltaDust Insecticide with a shaker can. Forprairie dogs thoroughly treat quarantine areas and holding areasas well as burrows in open fields. Thoroughly apply dust to ad-equately cover mound and around the perimeter (18” from theouter edge). Be sure to treat abandoned rodent burrows whichare suspected of containing fleas and ticks. Treat for a minimumof 5 days for light rodent populations, 10 days when populationsare dense. Apply as needed for control.


9

2.5"

4.5"

STORAGE AND DISPOSALDo not contaminate water, feed, or food by storage or dis-posal.Pesticide Storage: Store product in original container in acool, dry, locked place out of reach of children.Pesticide Disposal: Wastes resulting from the use of thisproduct may be disposed of on site or at an approved wastedisposal facility.Container Handling: Non-refillable container. Do not reuseor refill this container. Offer for recycling, if available. Punctureand dispose of in a sanitary landfill, or by other approved Stateand local procedures.Container Handling: (For Homeowner) Non-refillable con-tainer. Do not reuse or refill this container. Offer for recycling,if available. If empty: Place in trash or offer for recycling ifavailable. If partly filled: Call your local solid waste agencyfor disposal instructions. Never place unused product downan indoor or outdoor drain.

IMPORTANT: READ BEFORE USERead the entire Directions for Use, Conditions, Disclaimer of War-ranties and Limitations of Liability before using this product. Ifterms are not acceptable, return the unopened product containerat once. By using this product, user or buyer accepts the follow-ing Conditions, Disclaimer of Warranties and Limitations of Lia-bility.CONDITIONS: The directions for use of this product are believedto be adequate and must be followed carefully. However, it isimpossible to eliminate all risks associated with the use of thisproduct. Crop injury, ineffectiveness or other unintended conse-quences may result because of such factors as weather condi-tions, presence of other materials, or the manner of use orapplication, all of which are beyond the control of Bayer Crop-Science LP. All such risks shall be assumed by the user or buyer.DISCLAIMER OF WARRANTIES: TO THE EXTENT CONSISTENTWITH APPLICABLE LAW, BAYER CROPSCIENCE LP MAKES NOOTHER WARRANTIES, EXPRESS OR IMPLIED, OF MER-CHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE OROTHERWISE, THAT EXTEND BEYOND THE STATEMENTS MADEON THIS LABEL. No agent of Bayer CropScience LP is authorizedto make any warranties beyond those contained herein or tomodify the warranties contained herein. TO THE EXTENT CON-SISTENT WITH APPLICABLE LAW, BAYER CROPSCIENCE LP DIS-CLAIMS ANY LIABILITY WHATSOEVER FOR SPECIAL, INCIDENTALOR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE ORHANDLING OF THIS PRODUCT.LIMITATIONS OF LIABILITY: TO THE EXTENT CONSISTENT WITH


10

2.5"

4.5"

Produced for:Bayer Environmental ScienceA Division of Bayer CropScience LP2 T. W. Alexander DriveResearch Triangle Park, NC 27709

APPLICABLE LAW, THE EXCLUSIVE REMEDY OF THE USER ORBUYER FOR ANY AND ALL LOSSES, INJURIES OR DAMAGES RE-SULTING FROM THE USE OR HANDLING OF THIS PRODUCT,WHETHER IN CONTRACT, WARRANTY, TORT, NEGLIGENCE,STRICT LIABILITY OR OTHERWISE, SHALL NOT EXCEED THE PUR-CHASE PRICE PAID, OR AT BAYER CROPSCIENCE LP’S ELECTION,THE REPLACEMENT OF PRODUCT.

Actisol® is a registered trademark of William Evans.Bayer (reg’d), the Bayer Cross (reg’d) and DeltaDust® are regis-tered trademarks of Bayer.


4.5”

2.5” - ETL3”

Net Weight1 Pound0419107104494104F 141014AV4

INSECTICIDE

Deltamethrin..........................................................................0.05%...............................................99.95%

............................................................................100.00%

If on skin:

For and

Return to Index....

FIRST AIDIf on skin orclothing

If in eyes

If swallowed

any

If Inhaled

HOT LINE NUMBER

1-800-888-8372


Hazards to Humans and Domestic Animals

CAUTION/PRECAUCIÓN

Environmental Hazards

Physical and Chemical Hazards

GROUP 3 INSECTICIDE

For use in, on and around buildings and structures for the control of listed pests,including on lawns, ornamental trees andshrubs around residential, institutional,public, commercial, agricultural andindustrial buildings; and parks,recreational areas and athletic fields.

Do not use on golf course turf.

Active Ingredient:Lambda-cyhalothrin1

(CAS No. 91465-08-6): . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.7%

Other Ingredients: 90.3%

Total: 100.0%

1Synthetic pyrethroid, capsule suspension (microencapsulated)

KEEP OUT OF REACH OF CHILDREN.

CAUTION/PRECAUCIÓNSi usted no entiende la etiqueta, busque a alguien para que sela explique a usted en detalle. (If you do not understand the label, find someone to explain it to you in detail.)

See additional precautionary statements anddirections for use in booklet.

EPA Reg. No. 100-1066 EPA Est. 61282-WI-1

Product of the United Kingdom

SCP 1066A-L1N 1114

1 quartNet Contents

Return to Index...

CONDITIONS OF SALE AND LIMITATION OF WARRANTY AND LIABILITY

NOTICE:

TO THE EXTENT PERMITTED BY APPLICABLE LAW, THE EXCLUSIVE REMEDY OF THE USER OR BUYER, AND THE EXCLUSIVE LIABILITY OF SYNGENTA AND SELLER FOR ANY AND ALL CLAIMS, LOSSES, INJURIES OR DAMAGES (INCLUDING CLAIMS BASED ON BREACH OF WARRANTY, CONTRACT, NEGLIGENCE, TORT, STRICT LIABILITY OR OTHERWISE) RESULTING FROM THE USE OR HANDLING OF THIS PRODUCT, SHALL BE THE RETURN OF THE PURCHASE PRICE OF THE PRODUCT OR, AT THE ELECTION OF SYNGENTA OR SELLER, THE REPLACEMENT OF THE PRODUCT.

DIRECTIONS FOR USE

IMPORTANT:

Resistance Management

INFORMATION: STRUCTURAL AND PERIMETERPEST CONTROL

Mixing Instructions

® ®

Tank Mixing

®

Observe all restrictions and precautions which appear on the labels of these products.

Foam Applications

RATES FOR STRUCTURAL PESTS (HAND APPLICATION EQUIPMENT)

PestsConcentration

of AI Dilution Rate

PestsConcentration

of AI Dilution Rate

*

*

SPECIFIC USE DIRECTIONSAnts

Outdoor Surfaces Use

Cockroaches, Crickets, Earwigs, Firebrats, Silverfish, and Spiders


Bedbugs

Bees, Flies, Mosquitoes, and Wasps


Carpenter Bees

Pantry Pests (i.e., Carpet beetle, Cigarette beetle, Confused flour beetle, Lesser grain borer, Red flourbeetle, Rice weevil, and Saw-toothed grain beetle)

Boxelder Bugs, Centipedes, Millipedes, Pillbugs, and Sowbugs


Fleas and Ticks


Cluster Flies

Litter Beetles (Darkling, Hide, and Carrion Beetles) and Flies in Animal Housing (Such as Poultry Houses)

Livestock/Poultry Housing Structures and Pet KennelsApplication within Food-Handling Establishments

Application within Food-Serving Areas (facilities where foods are served, such as dining rooms)

Livestock/Poultry Housing Structures and Pet Kennels

DO NOT

DO NOT


Structural Perimeter Barrier Treatments

Rate Table for Structural Perimeter Barrier Applications

Application Rate of Demand CSInsecticide

Gallons of Water1

Area of Coverage (sq ft)

Examples of Dilutions for Structural Perimeter Barrier Applications

Application Volume:

Gallons of Solution/

1,000 sq ft

Application Rate of

Demand CS Insecticide/1,000 sq ft

Amount ofDemand CS Insecticide to

Dilute in Water According toSpray Tank Volumes

5 gallons 10 gallons 50 gallons

NOTE:

LET TREATED SURFACES DRY BEFORE ALLOWING HUMANS AND PETS TO CONTACT SURFACES.Do not Do not

Do notDo not

Do not

Do not

INFORMATION: LAWNS/TURFGRASS AND ORNAMENTALS

IMPORTANT:

Do not Do not Do not

Do not

Mixing Instructions (Turf and Ornamental Dilutions)

Tank Mixing (Turf and Ornamental Dilutions)

Tank Dilution Rates for Ornamental Pests

Use Pest

Amount ofDemand CS Insecticide

Ornamentals

NOTE:

Tank Mixing (Turf and Ornamental Dilutions)Scale:

Bagworm:

Demand CS Insecticide Mixing Chart for Ornamental Insect Pest Control

Rate ofDemand CSInsecticide

Amount of Demand CS Insecticide to Dilute inWater According to Spray Volumes

25gallons

50gallons

100gallons

200gallons

300gallons

Power Spray Rates for Lawn and Turfgrass Pests

Use Pests

Amount of Demand CS Insecticide

Lawns/Turfgrass

KEEP CHILDREN AND PETS OFF TREATED AREAS UNTIL SPRAY HAS DRIED FOLLOWING THE APPLICATION.

Surface Insect Control (armyworm, cutworms, fleas, etc.)

Thatch-Inhabiting Insect Control (chinch bugs, billbugs, etc.)

Subsurface Insect Control (mole crickets, grubs, etc.)

Fire Ant Control

Mosquito Control

Demand CS Insecticide Mixing Chart for Turf Insect Pest Control(Demand CS Insecticide to add per 100 gal spray tank)

Rate ofDemand CSInsecticide

Application Rate Per 1,000 sq ft of Turf

2 gallons 4 gallons 6 gallons 8 gallons 10 gallons

STORAGE AND DISPOSAL

Pesticide Storage

Pesticide Disposal

Container Handling

® ®

®

®

SCP 1066A-L1N 1114

CONT

ACT

INSE

CTIC

IDE

EcoP

CO A

CU®

DIRECTIONS FOR USE:IT IS A VIOLATION OF FEDERAL LAW TO USE THIS PRODUCT IN A MANNER INCONSISTENT WITH ITS LABELING. SHAKE WELL BEFORE USING. For Crawling Insects: Crack/Crevice and Void Treatments: Important – Use the injector nozzle tip provided. Inject into all crack/crevice and void spaces where insects are present. Applications can be made, but are not limited to, behind baseboards, cabinets, walls, ceilings, door and window frames, and around water pipes and appliances. Insects contacted by spray will be killed. Ensure contact with as many insects as possible. Fire ants & carpenter ants: this product will not kill ant queens or ant colonies. Fleas & Brown Dog Ticks: hold can approximately 12 inches above surface area and apply uniformly to infested areas such as carpets, rugs, cloth upholstery and pet bedding. Contact fleas & ticks directly to kill these pests. For Flying Insect Treatments: To kill these pests, aim spray toward flying insect infestations contacting as many insects as possible. Insects contacted by spray will be killed. Wipe away excess spray after application. Avoid spraying plants.

The following table provides the minimum and maximum time to obtain 100% contact mortality for tested insects in the laboratory. Flushing action and knockdown time were not measured in this testing.

Time to 100% Contact MortalityMinimum Maximum Insect Pest

1 min 1 min bed bugs, carpet beetle larvae, European earwigs, field crickets, house flies, Nuisance Ants (Including Argentine, thief, little black, big-headed, pavement,

leafcutter, acrobat, odorous house, velvety tree, pyramid, field, crazy, cornfield & large yellow), Pantry Pests (beetles, moths, mites & weevils)

1 min 5 min cat fleas, German cockroaches, southern fire ants5 mins 5 min American cockroaches, cellar spiders, silverfish, wolf spiders,

Occasional Invaders (Including centipedes, millipedes, crickets, earwigs, pillbugs, sow bugs & lady beetles)

15 min 1 hr southern house mosquitoes1 hr 1 hr brown dog ticks1 hr 24 hrs carpenter ants

This product is a contact spray and will not prevent reinfestation of any listed pest in any treated area. Insects must be contacted by spray in order to ensure 100% mortality.

Storage & DisposalDo not contaminate water, food or feed by storage or disposal.Storage: Store in a cool, dry area away from heat or open flame.Pesticide Disposal: Wastes resulting from the use of this product must be disposed of on site or at an approved waste disposal facility. Container Disposal: Do not puncture or incinerate! If empty: Place in trash or offer for recycling if available. If partly filled: Call your local solid waste agency or 1-800-CLEANUP for disposal instructions.

PRECAUTIONARY STATEMENTSHazards to Humans & Domestic AnimalsCAUTION — Causes moderate eye irritation. Avoid contact with eyes or clothing. Wear safety glasses, safety goggles, or face shield. Wash thoroughly with soap and water after handling and before eating, drinking, chewing gum, or using tobacco.

Physical or Chemical HazardsFlammable. Contents under pressure. Keep away from fire, sparks and heated surfaces. Do not puncture or incinerate container. Exposure to temperatures above 130°F may cause bursting.

Environmental HazardsFor terrestrial uses: Do not apply to water, or to areas where surface water is present or to intertidal areas below the mean high water mark. Do not contaminate water when disposing of equipment washwaters or rinsate.

FIRST AID • Hold eye open and rinse slowly and gently with water for 15-20 minutes. • Remove contact lenses, if present, after the first 5 minutes, then continue rinsing eye. • Call a poison control center or doctor for treatment advice.

HOT LINE NUMBER

Have the product container or label with you when calling a poison control center or doctor, or when going for treatment. You may also contact 1-800-535-5053 for emergency medical treatment information.

NOTE TO PHYSICIAN

Contains petroleum distillate – vomiting may cause aspiration pneumonia.

For Product Information: Call 1-888-326-7233 weekdays, 9:00 am to 5:00 pm CST.For Chemical Safety Information: Call 1-800-535-5053 anytime. (InfoTrac Chemical Response System)

Limitation of Liability: EcoSMART Technologies, Inc. makes no warranties of merchantability, or of fitness for a particular purpose, nor any other expressed or implied warranty except as stated above.

www.ecosmart.comContains no CFCs or other ozone depleting substances. Federal regulations prohibit CFC propellents in aerosols.

©2008 EcoSMART Technologies, Inc.,

3600 Mansell Rd., Suite 150, Alpharetta, GA 30022All rights reserved. Made In USA. U.S. Patent Nos. 6,004,569 & 6713518B1U.S. and Foreign Pat. Pending (USA)

Item No.29001 Revised 042008

EcoPCO® and the EcoSMART Technologies logo are registered trademarks of EcoSMART Technologies, Inc.

UNSCENTED CONTACT INSECTICIDEEcoPCO ACU

®

Kills the Following Crawling Insects On Contact Only: fire ants, carpenter ants, Argentine ants, German & American cockroaches, cat fleas, cellar spiders, wolf spiders, brown dog ticks, European earwigs, carpet beetle larvae, field crickets, pantry pests, nuisance ants, centipedes, millipedes, silverfish, pillbugs & sow bugs

Kills the Following Flying Insects On Contact Only: house flies, southern house mosquitoes & lady beetles

• Biopesticide• Active Ingredient

from Plant Oils• Leaves No Visible

Residue

EPA Reg. No. 67425-14

EPA EST. No. 11715-TN-1

NET CONTENTS: 17 OZ

CAUTIONKEEP OUT OF REACH

OF CHILDRENSee Back Panel for Additional

Precautions and First Aid

Active Ingredient:

®

2-Phenethyl Propionate ...............0.10%Other Ingredients*...........99.90%

100.00%*contains petroleum distillates

If In

Eye

s:

Return to Index...

Kills House Flies and Other Listed Filth Flies Easy to Use Odorless, no vapors or fumes Effective when applied indoors for up toseven months

EPA Reg. No. 8033-114-279EPA Est. No. 071637-FRA-001

Active Ingredient: By Wt.Acetamiprid............................................................ 4.4%Other Ingredients .................................................. 95.6%

100.0%


See back panel for additional precautions Si usted no entiende la etiqueta, busque a alguien para que se la explique a usteden detalie. (If you do not understand the label find someone to explain it to you indetail.)

FMC CorporationAgricultural Products Group1735 Market StreetPhiladelphia PA 19103Net Contents: 20 Stickers (Each with0.00042 Ounces Active Ingredient

07-10-13

PRECAUTIONARY STATEMENTS HAZARDS TO HUMANS AND DOMESTIC ANIMALSCAUTION Harmful if swallowed or absorbed through the skin. Avoid contact withskin, eyes or clothing. Wash thoroughly with soap and water after han-dling and before eating and drinking, chewing gum, using tobacco, orusing the toilet. Remove and wash contaminated clothing before reuse.Keep out of reach of children and domestic animals. Do not let childrenhandle stickers. Do not handle stickers with wet hands. ENVIRONMENTAL HAZARDS This product is toxic to wildlife. This product is very toxic to bees.

FIRST AID

NOTE TO PHYSICIAN

If on skin orclothing

If in eyes

If swallowed

• Rinse skin immediately with plenty of water for 15-20 minutes.• Take off clothing if contaminated.• Call a poison control center or doctor for treatment advice.

• Hold eye open and rinse slowly and gently with water for 15-20minutes.

• Remove contact lenses, if present, after first 5 minutes, then con-tinue rinsing eye.

• Call a poison control center or doctor for treatment advice.

• Call a poison control center or doctor immediately for treat-ment advice.

• Have person sip a glass of water if able to swallow.• Do not induce vomiting unless told to do so by a poison con-

trol center or doctor. • Do not give anything by mouth to an unconscious person.

Have the product container or label with you when calling a poison control center or doc-tor, or going for treatment. You may also contact 1-(800)-331-3148 for EmergencyAssistance.

Note to Physician: No specific antidote is available. Treat patient symptomatically.

DIRECTIONS FOR USE It is a violation of Federal Law to use this product in a manner inconsis-tent with its labeling. Read entire label before using this product. EndZone Insecticide Sticker kills flies that land on the sticker surfaceand ingest the sticker coating. Stickers work best when placed on ornear a window or other light source. However, in the absence of light orunder low-light conditions, stickers may be placed near a potential flyfood source (such as inside a garbage can). Stickers are effective for upto seven months when placed indoors and up to 4 months when placedoutdoors but protected from rain. Use Information:EndZone Insecticide Sticker is used to kill the following filth flies: houseflies, little house flies, blow flies, bottle flies, flesh flies, phorid flies, fun-gus gnats, and vinegar (fruit) flies. No fumes or vapors are released.The coating on each sticker is attractive to flies. Flies ingest the coatingand start to die within one minute. Dead flies do not stick to the surface.Remove dead flies with a brush or broom and dispose in trash, or byvacuuming. If a catch basin is used, remove dead flies on a routinebasis. Place stickers on windows, near light sources or other places, areas orsurfaces where flies congregate. Keep out of reach of children and pets.Stickers may be adhered to the outside and inside of fly light traps andbait stations. Stickers may be placed in commercial trash areas,kitchens and food storage areas. Place stickers in areas so that theyavoid becoming wet. The number of stickers to use is based on the size of the area whereflies are found. One sticker per 1000 cubic feet is recommended. Usemore stickers for heavy infestations. In rooms with high infestations, orfor quicker results, place a sticker in each window. Keep stickers dryafter application. Replace stickers that were applied indoors after 7months or outdoors after 4 months or as needed. Replace stickers

Return to Index...

1

3 4

21 2

3 4

sooner when contaminated by dust, dirt, filth, etc. Restrictions: Do not use on sky lights. Do not use in and around commercial barns, stables, and paddocks. Do not use in grazing areas, feed lots, poultry houses, or other similarareas used for housing, boarding, and/or rearing animals. This productmay be used around barns and stables on residential property. Do not allow children to handle stickers or let pets come in contact withthem. Do not place stickers directly above areas where food is stored or pre-pared. Applying stickers: Stickers have an adhesive coating on one side and a plastic cover onthe other. With dry hands remove cover from the adhesive coating side first.Place sticker in desired location. Once sticker is adhered, remove theplastic cover to expose the attractive coating.

For questions about the use of this product, call 1-800-321-1FMC(1362).

Conditions of Sale and Limitation of Warranty and Liability:

NOTICE: Read the entire Directions for Use and Conditions of Saleand Limitation of Warranty and Liability before buying or using thisproduct. If the terms are not acceptable, return the product at once,unopened, and the purchase price will be refunded.

The Directions for Use of this product must be followed carefully. It isimpossible to eliminate all risks inherently associated with the use ofthis product. Crop injury, ineffectiveness, or other unintended conse-quences may result because of such factors as manner of use or appli-cation, weather or crop conditions beyond the control of FMC or Seller.All such risks shall be assumed by Buyer and User, and Buyer andUser agree to hold FMC and Seller harmless for any claims relating tosuch factors.Seller warrants that this product conforms to the chemicaldescription on the label and is reasonably fit for the purposes stat-ed on the Directions for Use when used in accordance with thedirections under normal conditions of use. TO THE EXTENT CON-SISTENT WITH APPLICABLE LAW, FMC MAKES NO WARRANTIESOF MERCHANTABILITY OR OF FITNESS FOR A PARTICULARPURPOSE, NOR ANY OTHER EXPRESS OR IMPLIED WAR-RANTIES WITH RESPECT TO THE SELECTION, PURCHASE, ORUSE OF THIS PRODUCT. Any warranties, express or implied, hav-ing been made are inapplicable if this product has been used con-

trary to label instructions, or under abnormal conditions, or underconditions not reasonably foreseeable to (or beyond the control of)seller or FMC, and buyer assumes the risk of any such use.To the extent allowed by law, FMC or seller shall not be liable for anyincidental, consequential or special damages resulting from the use orhandling of this product. THE EXCLUSIVE REMEDY OF THE USEROR BUYER, AND THE EXCLUSIVE LIABILITY OF FMC AND SELLERFOR ANY AND ALL CLAIMS, LOSSES, INJURIES OR DAMAGES(INCLUDING CLAIMS BASED ON BREACH OF WARRANTY, CON-TRACT, NEGLIGENCE, TORT, STRICT LIABILITY OR OTHERWISE)RESULTING FROM THE USE OR HANDLING OF THIS PRODUCT,SHALL BE THE RETURN OF THE PURCHASE PRICE OF THEPRODUCT OR, AT THE ELECTION OF FMC OR SELLER, THEREPLACEMENT OF THE PRODUCT.This Conditions of Sale and Limitation of Warranty and Liability may notbe amended by any oral or written agreement.

Labeling for sticker:

EndZoneTM Insecticide StickerActive Ingredient: 4.4% acetamiprid

Contains 0.00042 ounces active ingredient EPA Reg. No 8033-114-279


Storage and DisposalDo not contaminate water, food, or feed by storage or disposal.Pesticide Storage: Store in original container in a cool, dry place outof the reach of children. Pesticide Disposal and Container HandlingCarton: Non refillable container. Do not reuse or refill this container.Offer for recycling, if available, or dispose of in trash.Stickers: Wrap used stickers in paper and dispose in trash.

IC3

INSECTICIDE CONCENTRATE


PRECAUCION AL USUARIO: Si usted no puede leer o entender inglés, no use este producto hasta que la etiqueta le haya sido explicada ampliamente. (TO THE USER: If you cannot read or understand English, do not use this product until the label has been fully explained to you.)

See inside label booklet for FIRST AID and PRECAUTIONARY STATEMENTS.

Safe and Effective*

Manufactured for Envincio LLC 501 Cascade Pointe Lane Suite 103, Cary, NC 27513

SHAKE WELL BEFORE USING

ACTIVE INGREDIENTS:Rosemary Oil ...................................................................................................... 10.00%Geraniol ................................................................................................................ 5.00%Peppermint Oil ...................................................................................................... 2.00% OTHER INGREDIENTS:Oil of Wintergreen, White Mineral Oil, Vanillin, Polyglyceryl Oleate ....................... 83.00%

TOTAL: ............................. 100.0%

Kills: Crawling and Flying Insect Pests

Quick Control with residual protectionMulti-purpose: for indoor, outdoor, fogging, turf and ornamental, on animal and mosquito misting applicationsContains natural essential plant oils with fresh scent

FIFRA 25(b) Exemption

*When used as directed.

This information is for promotional purposes only. Space considerations may require information to be omitted. Always refer to the actual package for complete label verbiage. This product may not yet be available or approved for sale or use in your area.

Return to Index...

DIRECTIONS FOR USE

READ ENTIRE LABEL — USE IN ACCORDANCE WITH LABEL INSTRUCTIONS

When using this product as a space spray in food processing plants, foods should be removed or covered during treatment. Do not apply as a space spray while food processing is underway. Food processing surfaces and equipment must be covered during treatment or cleaned with an effective detergent and rinsed with potable water before reuse. Food processing operations may continue when this product is applied as a surface spray with care and in accordance with the directions and precautions given below.

SHAKE WELL BEFORE USING

Maintain agitation in all spray systems Essentria IC3 is intended for use in and around buildings and structures as well as modes of transport.

INDOOR USE AREAS: Incudes, but is not limited to, apartment buildings, bakeries, beverage plants, bottling facilities, breweries, cafeterias, candy plants, canneries, cereal processing and manufacturing plants, dairy barns, poultry facilities, flour mills, food processing plants, frozen food plants, homes, hospitals, hotels, houses, industrial buildings, kennels, kitchens, laboratories, manufacturing facilities, mausoleums, meat processing and packaging plants, meat and vegetable canneries, motels, nursing homes, office buildings, restaurants, schools, stores, supermarkets, warehouses and similar structures.

OUTDOOR AREAS: Includes, but is not limited to, building foundations, dairy facilities, drive-in restaurants, drive-in theaters, golf courses, parks, playgrounds, poultry houses, recreational areas, schools, urban areas, lawns, landscape areas, trees, turf and zoos.

MODES OF TRANSPORT: Aircraft, buses, trucks, trailers, rail cars and marine vessels.

NOTE: For sensitive indoor/outdoor surfaces such as vinyl, plastic, fabric, wood floors, etc. test a small non-visible area first before spraying. This includes vinyl siding, outdoor furniture, storm doors and windows, etc. It is possible that Essentria IC3 may mar some sensitive surfaces. If spray gets on any sensitive surface that is listed, simply rinse with water and wipe off with clean cloth. Essentria IC3 may be diluted with water or oil and applied with conventional application equipment including, but not limited to, compressed air sprayers and power sprayers. When diluting with water, prepare only the amount needed for immediate use and maintain agitation during use. Do Not Store Spray Solution Overnight. For oil dilutions that are applied in food handling establishments, a deodorized petroleum oil which conforms to CFR 21 (especially section 172.884) is required (such as Exxon Isopar M, Ashland Low Odor Base Solvent or the equivalents). Tank mix applications must be made in accordance with the more restrictive of label limitations and precautions. No label dosages may be exceeded. This product cannot be tank mixed with any product with label prohibitions against such mixing.

Most effective results are achieved when used as part of a treatment protocol that includes physical, environmental and other chemical pest control measures.

INDOOR USE

Do not apply directly to house plants. Cover/avoid any pools or aquaria prior to spraying.

GENERAL PEST CONTROL: To control accessible, exposed stages of crawling insects including, but not limited to, ants, bed bugs, cockroaches, cadelles, cigarette beetles, dark mealworms, dried fruit beetles, drugstore beetles, confused floor beetles, fleas, grain mites, fowl mites, mites, nuisance beetles (such as lady beetles), red flour beetles, rice weevils, saw-toothed grain beetles, spiders, spider beetles, yellow mealworms in sites that include, but are not limited to, apartments, homes, restaurants, food processing plants, industrial installations and warehouses, dilute at the rate of up to 0.5 to 6 fluid ounces of Essentria IC3 per gallon of water (use lower rate for maintenance service and higher rates for active infestations). Thoroughly spray non-visible areas where these insects are usually found with special attention to cracks and crevices, niches, dark corners, drains and other harborage sites. When treating for bedbugs thoroughly clean, vacuum, and air mattresses and springs prior to treatment. Mix Essentria IC3 at a rate of 1 to 4 ounces per gallon of water and apply as a spot treatment to cracks and crevices, around baseboards, floorboards, headboards, and walls. In hotels and other public lodging facilities pay special attention to luggage stands and the adjacent area. On mattresses and springs spot treat only areas that may harbor pests. Concentrate on tufts, seams, folds, and creases. Repeat as necessary. To prevent potential

discoloring, do not spray on visible areas (i.e. baseboards, door frames, walls, etc.) and wipe away excess. Food processing operations may continue when Essentria IC3 is applied as a surface, spot or crack and crevice treatment in accordance with the directions and precautions given above.

FOGGING: To control crawling and flying insects (moths and flies, including house flies, horse flies, stable flies, horn flies, mosquitoes, gnats, fruit flies, phorid flies, etc) in sites that include, but are not limited to, food processing plants, (INCLUDING USDA INSPECTED FACILITIES), industrial installations, animal quarters (cattle barns, horse barns, poultry barns, swine houses, zoos and warehouses), Essentria IC3 may be applied as a space spray through conventional fogging equipment misting systems (including mist sprayers and mist blowers), automated spray systems, and/or related application technologies. Cover or remove exposed food and cover food-handling surfaces in edible product areas of food handling establishments. Also cover sensitive surfaces (plastics, etc). Close and shut off air conditioning or ventilating equipment. Mix 4 to 10 ounces of Essentria IC3 insecticide with sufficient oil to equal 1 gallon of diluted spray. (It is recommended to use lower rates in most food facility applications). Apply at a rate of 1 to 3 fluid ounces per 1000 cubic feet, filling the room with mist (or fog, if thermal equipment is used). Keep area closed for at least 15 minutes. Vacate treated area. Ventilate before reoccupying. Fogging may create slippery conditions on painted floor surfaces. Retreat if reinfestation occurs.

The product does contain plant oils that are inherently fragrant. When used in confined spaces, prolonged exposure to the fragrance may be objectionable to some individuals.

OUTDOOR USE

PERIMETER TREATMENTS AND RECREATIONAL AREAS: To control aphids, ants, bees, boxelder bugs, centipedes, cockroaches, crickets, darkling beetles, firebrats, fleas, ground beetles, fowl mites, mites, millipedes, pillbugs, silverfish, sowbugs, spiders, ticks and wasps. In compressed air sprayers, dilute 1 to 8 ounces of Essentria IC3 per gallon of water (use lower rate for maintenance service and higher rates for active infestations) and apply at the rate of 2 gallons per 1000 square feet or until area is thoroughly wet. Also apply to a band of soil and vegetation 6 to 10 feet wide around and adjacent to buildings. Treat the building foundation to a height of 2 to 3 feet with sufficient water for coverage. Make special efforts to spray areas where pest species congregate such as, but not limited to, waste receptacles, dumpsters, unoccupied picnic tables, the exterior of food handling establishments, and food pavilions. Additionally apply around potential entry areas such as, but not limited to, eves, windows, doorways, porches, porch lights, and around utility boxes. For power sprayers, mix approximately 1 to 6 ounces of Essentria IC3 per gallon of water (use lower rate for maintenance service and higher rates for active infestations) and apply until area is sufficiently covered (usually min. 4 gallons per 1000 square feet.). Maintain agitation. Repeat as necessary.

MOUND DRENCH METHOD - FOR CONTROL OF FIRE ANTS AND OTHER MOUNDING ANTS: Dilute 2 to 4 ounces of Essentria IC3 per gallon of water. Apply 1 to 2 gallons of emulsion to each mound area by sprinkling the mound until it is wet and treat a 4 foot diameter circle around the mound. Use the higher volume for mounds larger than 12 inches. For best results, apply in cool weather, such as the early morning or late evening hours, but not in the heat of the day.

MOSQUITO CONTROL AND OTHER BITING FLIES - OUTDOOR YARD OR BARRIER TREATMENT: To control adult mosquitoes and other biting flies using ground application, dilute 1 to 3 fluid ounces of Essentria IC3 per gallon of water. Treat harborage areas such as shrubbery and vegetation where mosquitoes/flies may rest. Shrubbery and vegetation around stagnant pools, marshy areas, ponds and shorelines may be treated. Repeat as necessary.

MOSQUITO CONTROL AND OTHER BITING INSECTS - AUTOMATIC SPRAYING SYSTEMS: Automatic spraying systems must not be programmed to release pesticides where food or feed is directly exposed. To control flies, house flies, horn flies, stable flies, horse flies, mosquitoes and gnats, add concentrate to tank and add water to obtain desired dilution. Agitate well while adding water and maintain thorough agitation while system is in use. In automatic spraying systems like, but not limited to, misting systems used for mosquito and other biting insect control, solutions of Essentria IC3 may be stored for extended periods of time, not to exceed one month, as long as the system has agitation and the appropriate quantity of adjuvant is used. Dispense diluted concentrate through automatic spraying system. Set nozzles to deliver one ounce liquid per minute. Locate nozzles to cover a maximum of 2,000 cubic feet of space per nozzle. Set timer to operate in accordance with equipment directions. Dilute Essentria IC3 just prior to use at 0.5 to 3 ounces per gallon of water (Use lower dilution rates for preventative applications).

TO CONTROL SPIDERS, FLYING INSECTS, AND OTHER NUISANCE PESTS ON AND AROUND BOAT DOCKS: As an aid in the elimination of their harborage areas, dilute 2 to 8 ounces of Essentria IC3 per gallon of water and apply at the rate of 2 gallons per 1000 square feet or until area is thoroughly wet. Since flying insects can migrate in and out of the treatment area, it is recommended to use this product as part of an Integrated Pest Management (IPM) program. This includes, but is not limited to, eliminating breeding and harborage sites.

USE ON TURF AND GRASS: Used alone as a contact spray. To control Ants, Armyworms, Billbugs, Chinch Bugs, Chiggers, Crickets, Cutworms, Earwigs, Fleas, Grasshoppers, Hyperodes Weevils (adults), Japanese Beetles (adults), Mole Crickets, Sod Webworms and Ticks, dilute in a compressed air sprayer (or backpack) 2 to 4 ounces of Essentria IC3 per gallon of water and apply at the rate of 2 to 4 gallons per 1000 square feet or until area is thoroughly wet. For power sprayers mix approximately 2 to 4 ounces per gallon of water and apply until area is sufficiently covered (usually min. 4 gallons per 1000 square feet with power sprayer). Exceeding rates may create potential phytotoxicity of turf surfaces.

USE ON NON-BEARING TREES AND SHRUBS: To control Mites, Scale Insects, Mealybugs, Aphids, Lace Bugs, Whiteflies, Tent Caterpillars, Bagworms and Beetles, dilute up to 1 to 2 ounces of Essentria IC3 per gallon of water and apply using a compressed air sprayer or power sprayer until foliage is thoroughly wet. Maintain agitation.

Exceeding rates may create potential phytotoxicity on plant surfaces. Dilute with enough water to obtain thorough coverage.

LIVESTOCK USE DIRECTIONS

USE INSECT ESSENTRIA IC3 REMARKSLivestock Spray (Beef Cattle, Swine, Goats and Sheep)

To control flying insects, including, but not limited to: Flies, House Flies, Deer Flies, Stable Flies and aids in the control of Face Flies

1 to 3 ounces per gal of mineral oil USP

Dilute in mineral oil USP as indicated and spray directly on the animal in sufficient amounts for proper coverage. There is no withholding period from last application to slaughter.

Ticks and Lice 1 to 3 ounces per gal of mineral oil USP

Apply as above

LivestockSpray(LactatingDairy Cattle)

To control flying insects, including, but not limited to: Flies, House Flies, Deer Flies, Stable Flies and aids in the control of Face Flies


Dilute in mineral oil USP as indicated. Direct spray to cover thoroughly. Repeat as necessary. No milk discard is required. Care should be taken that the spray does not come in direct contact with the lactating cow’s teats unless they are washed with an approved cleansing solution and dried before milking. Apply the spray at least 20 min. prior to milking or after milking has been complete.

Ticks and Lice 1 to 3 ounces per gal of mineral oil USP

Apply as above

Horses To control flying insects, including, but not limited to: Flies, House Flies, Deer Flies, Stable Flies and aids in the control of Face Flies


Dilute in mineral oil USP as indicated and spray directly on the animal in sufficient amounts for proper coverage.

Poultry Poultry Lice, Bedbugs, and Mites


Spray roosts, roost poles, walls (especially cracks in walls), and nests or cages thoroughly. It is not necessary to remove poultry from the housing unit during treatment. This should be followed by spraying over the birds with a fine mist.

PREMISE USE DIRECTIONS FOR LIVESTOCK FACILITIES

USE INSECT ESSENTRIA IC3 IN WATER OR MINERAL OIL

REMARKS

Residual Surface Spray

Flies, Gnats, Litter Beetles, Darkling Beetles (lesser meal worms) Mosquitoes, Spiders, Wasps

3 to 6 ounces per gal of water or mineral oil USP

Apply 1 gallon of dilution per 500 - 1000 sq. ft. Thoroughly cover walls, ceilings or other areas where pests rest or congregate in dairy barns, horse barns, poultry houses, swine buildings, livestock sheds, and other farm buildings.

Larvacide Maggots (fly larvae) 4 to 8 ounces per gal of water or mineral oil USP

Apply 1 gallon of dilution per 100 sq. ft. of droppings as a coarse spray. Repeat at 7 - 10 day intervals until droppings begin to cone up, then treat only “hot spots” (small areas found to have large number of maggots).

FOR CHEMICAL SPILL, LEAK, FIRE, OR EXPOSURE CALL: CHEMTREC 1-800-424-9300

FOR MEDICAL EMERGENCIES ONLY CALL: 1-866-257-4118

KEEP ALL INSECTICIDES OUT OF REACH OF CHILDREN

FIRST AIDIf IN Eyes:

15-20 minutes.

minutes, then continue rinsing eye.

If ON Skin: If INHALED:

If INGESTED:

Seek medical attention if necessary.

PRECAUTIONARY STATEMENTSCaution – May cause eye and skin irritation. Avoid contact with eyes, skin and clothing.

PERSONAL PROTECTIVE EQUIPMENT (PPE): Persons handling concentrate are recommended to wear:

USER SAFETY RECOMMENDATIONS: User should wash hands before eating, drinking, chewing gum, using tobacco, or using the toilet. Remove clothing immediately if the product gets inside. Wash thoroughly and put on clean clothing. Remove PPE after handling this product. Wash the outside of the gloves before removing.

PHYSICAL AND CHEMICAL HAZARDS: Do not use, pour, spill or store near heat or open flame. Store only in original container.

STORAGE & DISPOSALDo not contaminate water, food or feed by storage or disposal.

FOR CONTAINERS LARGER THAN ONE GALLON: PESTICIDE STORAGE AND SPILL PROCEDURES: Store upright at room temperature. Avoid exposure to extreme temperatures. In case of spill or leakage, soak up with an absorbent material such as sand, sawdust, earth, fuller’s earth, etc. Dispose of with trash.

CONTAINER DISPOSAL: Triple rinse or its equivalent, then offer for recycling or reconditioning, or puncture and dispose of with ordinary trash.

STORAGE: Store in original container in a dry cool place inaccessible to children and pets.

DISPOSAL: Do not reuse container. Discard in trash.

LIMITATION OF LIABILITY

To the fullest extent permitted by law, the manufacturer disclaims any liability whatsoever for special, incidental or consequential damages resulting from the use or handling of this product. Buyer assumes all responsibility for safety and use not in accordance with label, directions and precautionary statements.

Envincio represents that this product is a Minimum-Risk pest control product, and qualifies for exemption from EPA registration under the Federal Insecticide, Fungicide and Rodenticide Act (FIFRA).

Envincio, LLC 501 Cascade Pointe Lane Suite 103, Cary, NC 27513

All Rights Reserved. Made in USA.

U.S. Patent Nos. 6,004,569 U.S. and Foreign Patent Pending

Essentria is a trademark of Envincio LLC.

™

NET W

T:18

lbs

(8.2

kg)

Kills

War

farin

Res

istan

t Nor

way R

ats A

nd H

ouse

Mice®

FIN

AL

AL

L-W

EA

TH

ER

BL

OX

TM

ACTI

VE IN

GRED

IENT

: Br

odifa

coum

(CA

S #5

6073

-10-

0): .

. . .

. . .

0.0

05%

OTHE

R IN

GRED

IENT

S : .

. . . .

. . . .

. . . .

. 99

.995

%

TO

TAL

100.

000%

Con

tains

Den

aton

ium B

enzo

ate

†

†

See

back

pan

els

for F

irst A

id a

nd a

dditio

nal p

reca

utio

nary

sta

tem

ents

.

Mol

d Re

sist

ant •

Moi

stur

e Re

sist

ant

*Not

perm

itted f

or us

e aga

inst th

e foll

owing

spec

ies in

Califo

rnia:

Cotto

n rat,

Easte

rn ha

rvest

mous

e, Go

lden m

ouse

, Poly

nesia

n rat,

Mea

dow

vole,

Whit

e-thro

ated w

oodra

t, Sou

thern

plains

wood

rat, a

nd M

exica

n woo

drat

KEEP

OUT

OF

REAC

H O

F CH

ILDR

ENC

AUTI

ON

KIL

LS R

ATS,

MIC

E &

MEA

DO

W V

OLE

S*

SPEC

IMEN

LAB

EL

3699 Kinsman Blvd.Madison, WI 53704 U.S.A.

www.belllabs.comMADE IN USA

Manufactured by:

®FINALALL-WEATHER BLOX TM

Moisture Resistant • Mold Resistant


See side panels for First Aid and additional precautionary statements.

Kills Warfarin Resistant Norway Rats And House Mice

STORAGE AND DISPOSALDo not contaminate water, food or feed by storage or disposal.Pesticide Storage: Store only in original container in a cool, dry place inaccessible to children and pets. Keep containers closed and away from other chemicals.Pesticide Disposal: Dispose of wastes resulting from the use of this product in trash or at an approved waste disposal facility.Container Handling: Nonrefillable container. Do not reuse or refill this container. [Plastic:] Offer for recycling or reconditioning; or puncture and dispose of in a sanitary landfill; or by incineration. In most states, burning is not allowed.

WARRANTY: To the extent consistent with applicable law, seller makes no warranty, expressed or implied, concerning the use of this product other than indicated on the label. Buyer assumes all risk of use and/or handling of this material when such use and/or handling is contrary to label instructions.

EPA REG. NO.: 12455-89 EPA EST. NO.: 12455-WI-1

Norway rats, roof rats, and house mice may consume alethal dose in one night's feeding with first dead rodentsappearing four or five days after feeding begins.

KILLS RATS, MICE & MEADOW VOLES*

NET WEIGHT: 18 lbs (8.2 kg)

Product Code: FB1018 587FB-6 100915/08-15

DIRECTIONS FOR USEIt is a violation of Federal law to use this product in a manner inconsistent with its labeling.READ THIS LABEL: Read this entire label and follow all use directions and use precautions. Use only for the sites, pests, and application methods described on this label.

IMPORTANT: Do not expose children, pets, or nontarget animals to rodenticides. To help to prevent exposure:1. Store unused product out of reach of children and pets.2. Apply bait in locations out of reach of children, pets, domestic animals and nontarget wildlife, or in tamper- resistant bait stations. These stations must be resistant to destruction by dogs and by children under six years of age, and must be used in a manner that prevents such children from reaching into bait compartments and obtaining bait. If bait can be shaken from bait stations when they are lifted, units must be secured or otherwise immobilized. Stronger bait stations are needed in areas open to hoofed livestock, raccoons, bears, or other potentially destructive animals, or in areas prone to vandalism. 3. Dispose of product container and unused, spoiled, or unconsumed bait as specified on this label. Bait stations are mandatory for outdoor, above-ground use. Tamper-resistant bait stations must be used wherever children, pets, non-target mammals, or birds may have access to the bait placement location.

USE RESTRICTIONS: This product may only be used to control the following rodent pests in and around man-made structures: House mouse (Mus musculus), Norway rat (Rattus norvegicus), Roof rat (Rattus rattus), Cotton rat* (Sigmodon hispidus), Eastern harvest mouse* (Reithrodontomys humuli), Golden mouse* (Ochrotomys nuttalli), Polynesian rat* (Rattus exulans), Meadow vole* (Microtus pennsylvanicus), White-throated woodrat* (Neotoma albigula), Southern plains woodrat* (Neotoma micropus), and Mexican woodrat* (Neotoma mexicana). This product must be used in and within 100 feet of man-made structures constructed in a manner so as to be vulnerable to commensal rodent invasions and/or to harboring or attracting rodent infestations. Examples of such structures include homes and other permanent or temporary residences, food processing facilities, industrial and commercial buildings, trash receptacles, agricultural and public buildings, transport vehicles (ships, trains, aircraft), docks and port or terminal buildings and related structures around and associated with these sites. Fence and perimeter baiting, beyond 100 feet from a structure as defined above, is prohibited. This product must not be applied directly to food or feed crops.

Burrow baiting with FINAL All-Weather Blox is prohibited.

This product may also be used in alleys and sewers. Do not place near or inside ventilation duct openings. Do not contaminate water, food, feedstuffs, food or feed handling equipment, or milk or meat handling equipment or surfaces that come into direct contact with food. Do not broadcast bait. When used in USDA inspected facilities, this product must be applied in tamper-resistant bait stations.

Do not sell this product in individual containers holding less than 16 pounds of bait.

SELECTION OF TREATMENT AREAS: Determine areas where rats, mice, or meadow voles* will most likely find and consume the bait. Generally, these areas are along walls, by gnawed openings, in corners and concealed places, between floors and walls, or in locations where rats, mice, or meadow voles*, or their signs have been seen. Protect bait from rain and snow. Remove as much alternative food as possible.

APPLICATION DIRECTIONS:RATS: Place 5 to 22 blocks (at intervals of 15 to 30 feet) per placement in infested areas. Maintain an uninterrupted supply of fresh bait for at least 10 days or until signs of rat activity cease.

For use in sewers, thread wire through block and securely attach to a stationary structure such as the bottom step of a manhole ladder or a sewer grate. Allow just enough wire for the block to rest on manhole benching. If benching is not present, suspend block a few inches above the high water mark or secure block on a board supported by opposing steps of the ladder. Securing block in this manner will prevent removal by rats or water. Use at least 15 blocks per manhole. Maintain an uninterrupt-ed supply of fresh bait for at least 10 days or until signs of rat activity cease.

MICE AND MEADOW VOLES*: Place 1 block per placement. Space placements at 8- to 12-foot intervals in infested areas. Two blocks may be needed at points of very high activity. Maintain an uninterrupted supply of fresh bait for at least 15 days or until signs of mouse or meadow vole* activity cease.FOLLOW-UP: Replace contaminated or spoiled bait immediately. Wearing gloves, collect and dispose of all dead, exposed animals and leftover bait. To prevent reinfestation, limit sources of rodent food, water, and harborage as much as possible. If reinfestation does occur, repeat treatment. Where a continuous source of infestation is present, establish permanent bait stations and replenish as needed.

PRECAUTIONARY STATEMENTSHazards to Humans and Domestic AnimalsCAUTION: Harmful if swallowed. Causes moderate eye irritation. Keep away from children, domestic animals and pets. Do not get in eyes or on clothing.All handlers (including applicators) must wear shoes plus socks, and gloves. Any person who retrieves carcasses or unused bait following application of this product must wear gloves.

ENVIRONMENTAL HAZARDSThis product is extremely toxic to mammals and birds. Dogs, cats and other predatory and scavenging mammals and birds might be poisoned if they feed upon animals that have eaten this bait. This pesticide is toxic to fish. Do not apply directly to water, or to areas where surface water is present or to intertidal areas below the mean high water mark. Runoff also may be hazardous to aquatic organisms in water adjacent to treated areas. Do not contaminate water when disposing of equipment wash water or rinsate.

*Not permitted for use against the following species in California: Cotton rat, Eastern harvest mouse, Golden mouse, Polynesian rat, Meadow vole, White-throated woodrat, Southern plains woodrat, and Mexican woodrat.

User Safety RequirementsFollow manufacturer’s instruction for cleaning/maintaining PPE. If no such instructions for washables, use detergent and hot water. Keep and wash PPE separately from other laundry. Remove PPE immediately after handling this product. Wash the outside of gloves before removing. As soon as possible, wash hands thoroughly after applying bait and before eating, drinking, chewing gum, using tobacco or using the toilet and change into clean clothing.

NOTE TO PHYSICIAN If swallowed, this material may reduce the clotting ability of the blood and cause bleeding. If ingested, administer Vitamin K1 intramuscularly or orally. Vitamin K1 is antidotal at doses of 10−20 mg (not mg/kg). Repeat as necessary based on monitoring of prothrombin times.

TREATMENT FOR PET POISONINGIf animal eats bait, call veterinarian or 1-877-854-2494 at once.

NOTE TO VETERINARIANAnticoagulant Brodifacoum: For animals ingesting bait and/or showing poisoning signs (bleeding or elevated prothrombin times), give Vitamin K1 at doses of 2−5 mg/kg. If needed, check prothrombin times every 3 days until values return to normal (up to 30 days). In severe cases, blood transfusions may be needed.

FIRST AIDHAVE LABEL WITH YOU WHEN OBTAINING TREATMENT ADVICE

If Swallowed • Call a poison control center, doctor, or 1-877-854-2494 immediately for treatment advice. • Have a person sip a glass of water if able to swallow. • Do not induce vomiting unless told to do so by the poison control center or doctor.

If On Skin • Take off contaminated clothing. • Rinse skin immediately with plenty of water for 15−20 minutes. • Call a poison control center, doctor for treatment advice.

If in Eyes • Hold eye open and rinse slowly and gently with water for 15−20 minutes. • Remove contact lenses, if present, after the first 5 minutes, then continue rinsing eye. • Call a poison control center, doctor, or 1-877-854-2494 immediately for treatment advice.

DIRECTIONS FOR USE (Continued from other panel)

ACTIVE INGREDIENT: Brodifacoum (CAS #56073-10-0): . . . . . . . . . . . . . . . . . . . . . . . 0.005%OTHER INGREDIENTS†: . . . . . . . . . . . . . . . . . . . . . . . . 99.995% TOTAL 100.000% Contains Denatonium Benzoate†

SPECIMEN LABEL

Form 36866 (11/2015)

THE COMPLETE LABEL FOR THIS PRODUCT CONSISTS OF THE CONTAINER LABEL ANDTHE APPLICATOR’S MANUAL WHICH MUST ACCOMPANY THE PRODUCT. READ AND UNDER-STAND THE ENTIRE CONTAINER LABEL AND APPLICATOR’S MANUAL.A FUMIGATION MANAGEMENT PLAN MUST BE WRITTEN FOR ALL FUMIGATIONS PRIOR TOACTUAL TREATMENT.CONSULT WITH YOUR STATE LEAD PESTICIDE REGULATORY AGENCY TO DETERMINE REG-ULATORY STATUS, REQUIREMENTS, AND RESTRICTIONS FOR FUMIGATION USE IN THATSTATE. CALL 540-234-9281 / 1-800-330-2525 IF YOU HAVE ANY QUESTIONS OR DO NOTUNDERSTAND ANY PART OF THIS LABELING.

RESTRICTED USE PESTICIDEDUE TO HIGH ACUTE INHALATION TOXICITY OF PHOSPHINE GAS

FOR RETAIL SALE TO DEALERS AND CERTIFIED APPLICATORS ONLY. FOR USE BY CERTIFIED APPLICATORS OR PERSONS UNDER THEIR DIRECT SUPERVISION, AND ONLY FOR

THOSE USES COVERED BY THE CERTIFIED APPLICATOR’S CERTIFICATION. REFER TO THE DIRECTIONS IN THIS APPLICATOR’S MANUAL FOR REQUIREMENTS OF THE PHYSICAL

PRESENCE OF A CERTIFIED APPLICATOR.

APPLICATOR’S MANUALFOR

FOR USE AGAINST INSECTS WHICH INFEST STORED COMMODITIES AND CONTROL OF BURROWING PESTS

Active Ingredient: Aluminum Phosphide ............. 55.0%Inert Ingredients:...................................................... 45.0%Total ..........................................................................100.0%

KEEP OUT OF REACH OF CHILDRENDANGER - POISON - PELIGRO

FOR BURROWING RODENT APPLICATIONS: THE USE OF THIS PRODUCT IS STRICTLY PROHIBITED WITHIN100 FEET OF ANY BUILDING WHERE HUMANS AND/OR DOMESTIC ANIMALS DO OR MAY RESIDE ON

SINGLE OR MULTI-FAMILY RESIDENTIAL PROPERTIES AND NURSING HOMES, SCHOOLS (EXCEPT ATHLETIC FIELDS), DAYCARE FACILITIES AND HOSPITALS.

PRECAUCION AL USUARIO: Si usted no puede leer ingles, no use este productohasta que el marbete le haya sido completamente explicado.(TO THE USER: If you cannot read English, do not use this product until the label hasbeen fully explained to you.)

D & D HOLDINGS, INC.P.O. Box 116

153 Triangle DriveWeyers Cave, VA 24486 USA

Telephone: (540)234-9281/1-800-330-2525Fax: (540)234-8225

Internet: www.degeschamerica.comE-mail: [email protected]

EPA Est. Nos. 073926-CHN-001, 073927-CHN-0015857-NC-001 or 40285-VA-01

EPA Reg. Nos. 72959-1 and 72959-2

Manufactured for:

TABLETS AND PELLETS

Return to Index...

WARRANTYSeller warrants that the product conforms to its chemical description and whenused according to label directions under normal conditions of use, it is reason-ably fit for the purposes stated on the label. To the extent consistent with appli-cable law, the Seller makes no other warranty, either expressed or implied, andBuyer assumes all risks should the product be used contrary to the label.

TABLE OF CONTENTS

SECTION DESCRIPTION PAGE NUMBER

RESTRICTED USE STATEMENT ...........................................Front Cover

WARRANTY .................................................................Inside Front Cover

1 FIRST AID ..................................................................................................1Hot Line Number ........................................................................................1

2 NOTE TO PHYSICIAN................................................................................1

3 PRODUCT INFORMATION........................................................................2

4 PRECAUTIONARY STATEMENTS............................................................34.1 Hazards to Humans and Domestic Animals .....................................34.2 Environmental Hazards.....................................................................44.3 Physical and Chemical Hazards .......................................................4

DIRECTIONS FOR USE ............................................................................5

5 PESTS CONTROLLED ..............................................................................5

6 COMMODITIES WHICH MAY BE FUMIGATED ........................................66.1 Raw Agricultural Commodities, Animal Feed....................................66.2 Processed Foods ..............................................................................66.3 Non-Food Commodities ....................................................................7

7 EXPOSURE CONDITIONS FOR ALL FUMIGATIONS .............................8

8 DOSAGE RATES FOR COMMODITIES & BURROWING PESTS ...........98.1 Maximum Allowable Dosages...........................................................98.2 Advisory Dosages for Various Types of Fumigations .......................9

9 PROTECTIVE CLOTHING .......................................................................11

10 RESPIRATORY PROTECTION ................................................................1110.1 When Respiratory Protection Must Be Worn ..................................1110.2 Permissible Gas Concentration Ranges .........................................1110.3 Requirements for Availability of Respiratory Protection..................11

11 REQUIREMENTS FOR CERTIFIED APPLICATORS ..............................11

12 TRAINING REQUIREMENTS FOR RECEIPT OF IN-TRANSIT VEHICLES................................................................................................12

13 GAS DETECTION EQUIPMENT..............................................................12

14 NOTIFICATION REQUIREMENTS ..........................................................1314.1 Authorities and On-Site Workers ....................................................1314.2 Incident Reporting...........................................................................1314.3 Theft of Products ............................................................................13

15 APPLICATOR AND WORKER EXPOSURE............................................1315.1 Exposure Limits ..............................................................................1315.2 Application of Fumigant ..................................................................1315.3 Leakage from Fumigated Sites.......................................................1315.4 Aeration and Re-entry.....................................................................1415.5 Handling Unaerated Commodities..................................................1415.6 Industrial Hygiene Monitoring .........................................................1415.7 Engineering Controls and Work Practices ......................................14

16 PLACARDING OF FUMIGATED AREAS ................................................14

17 SEALING OF STRUCTURES ..................................................................15

18 AERATION OF FUMIGATED COMMODITIES ........................................1618.1 Foods and Feeds............................................................................1618.2 Non-Food Commodities ..................................................................1618.3 Tobacco...........................................................................................16

19 STORAGE INSTRUCTIONS ....................................................................1619.1 Labeling of Storage.........................................................................16

20 TRANSPORTATION INSTRUCTIONS.....................................................1720.1 Transport Designations...................................................................1720.2 Transportation Special Permit.........................................................17

21 FUMIGATION MANAGEMENT PLAN .....................................................18STEPS FOR PREPARATION OF THE REQUIRED WRITTEN FUMIGATION MANAGEMENT PLAN .....................................................19Purpose ...................................................................................................19A checklist guide for a fumigation management plan

A. Preliminary Planning & Preparation ...............................................20B. Personnel .......................................................................................21C. Monitoring ......................................................................................21D. Notification .....................................................................................22E. Sealing Procedures ........................................................................22F. Application Procedures & Fumigation Period.....................................22G. Post-Application Operations ..........................................................22

22 APPLICATION PROCEDURES ...............................................................2322.1 Farm Bins........................................................................................2322.2 Flat Storages...................................................................................2422.3 Vertical Storage...............................................................................25


22.4 Mills, food processing plants & warehouses ................................2622.5 Railcars, containers, trucks, vans, and other vehicles .................2722.6 Tarpaulin and bunker fumigations ................................................2722.7 In-Transit Shiphold Fumigation.....................................................28

22.7.1 General Information..........................................................2922.7.2 Pre-Voyage Fumigation Procedures ................................2922.7.3 Application Procedures for Bulk Dry Cargo Vessels ........3022.7.4 In-Transit Fumigation of Transport Units Aboard Ships ...3022.7.5 Precautions and Procedures During Voyage ...................3022.7.6 Precautions and Procedures During Discharge ...............31

23 BARGES ..................................................................................................31

24 SMALL SEALABLE ENCLOSURES.......................................................31

25 BEEHIVES, SUPERS AND OTHER BEE KEEPING EQUIPMENT ........31

26 BURROWING PEST CONTROL..............................................................3126.1 Use Restrictions ...........................................................................3226.2 Application Directions ...................................................................33

26.2.1 For Species with Open Burrow Systems..........................3326.2.2 For Species with Closed Burrow Systems .......................33

26.3 Environmental Hazards ................................................................3426.4 Endangered Species Restrictions ................................................34

26.4.1 Special Local Restrictions ................................................35

27 FUMI-SLEEVE® DUST RETAINER METHOD ........................................36

28 DISPOSAL INSTRUCTIONS ...................................................................3728.1 General .........................................................................................3728.2 Directions for Deactivation ...........................................................3828.2.A Wet Deactivation ..........................................................................3828.2.B Dr Deactivation .............................................................................3828.3 Directions for Disposal of Residual Dust......................................39

29 SPILL AND LEAK PROCEDURES .........................................................3929.1 General Precautions and Directions.............................................39

FOR ASSISTANCE CONTACT NUMBERS.............................................40


1

1. FIRST AID

Symptoms of exposure to this product are headaches, dizziness, nausea, difficultbreathing, vomiting and diarrhea. In all cases of overexposure get medical atten-tion immediately. Take victim to a doctor or emergency treatment facility.If inhaled:• Move person to fresh air.• If person is not breathing, call 911 or an ambulance; then give artificial respira-

tion, preferably by mouth-to-mouth, if possible.• Call a poison control center or doctor for treatment advice.If swallowed:• Call a poison control center or doctor immediately for treatment advice.• Have person sip a glass of water if able to swallow. Do not induce vomiting

unless told to by a poison control center or doctor.• Do not give anything by mouth to an unconscious person.If on skin or clothing:• Take off contaminated clothing.• Rinse skin immediately with plenty of water for 15-20 minutes.• Call a poison control center or doctor for treatment advice.If in eyes:• Hold eye open and rinse slowly and gently with water for 15-20 minutes.• Remove contact lenses, if present, after the first 5 minutes, then continue

rinsing eye.• Call a poison control center or doctor for further treatment advice.

2. NOTE TO PHYSICIAN

Aluminum phosphide fumigants react with moisture from the air, water, acids andmany other liquids to release phosphine gas. Mild inhalation exposure causesmalaise (indefinite feeling of sickness), ringing of ears, fatigue, nausea, and pressurein the chest, which is relieved by removal to fresh air. Moderate poisoning causesweakness, vomiting, and pain just above the stomach, chest pain, diarrhea and dys-pnea (difficulty in breathing). Symptoms of severe poisoning may occur within a fewhours to several days, resulting in pulmonary edema (fluid in lungs) and may lead todizziness, cyanosis (blue or purple skin color), unconsciousness, and death.

In sufficient quantity, phosphine affects the liver, kidneys, lungs, nervous system, and cir-culatory system. Inhalation can cause lung edema (fluid in lungs) and hyperemia (excessof blood in a body part), small perivascular brain hemorrhages and brain edema (fluid inbrain). Ingestion can cause lung and brain symptoms but damage to the viscera (body

HOT LINE NUMBERHave the product container, label or Applicator’s Manual with you when calling a poison control center or doctor, or going for treatment. CONTACT 1-800-308-4856FOR ASSISTANCE WITH HUMAN OR ANIMAL MEDICAL EMERGENCIES. You mayalso contact DEGESCH AMERICA, INC. – (540)234-9281/1-800-330-2525 – PEST-CON SYSTEMS DIV. – (252)237-7923/1-800-548-2778 - or CHEMTREC – 1-800-424-9300 for all other chemical emergencies.

2

cavity organs) is more common. Phosphine poisoning may result in (1) pulmonaryedema, (2) liver elevated serum GOT, LDH and alkaline phosphatase, reduced prothrom-bin, hemorrhage and jaundice (yellow skin color) and (3) kidney hematuria (blood in urine)and anuria (abnormal lack of urination). Pathology is characteristic of hypoxia (oxygendeficiency in body tissue). Frequent exposure to concentrations above permissible levelsover a period of days or weeks may cause poisoning. Treatment is symptomatic.The following measures are suggested for use by the physicians in accordance withtheir own judgment.In its milder forms, symptoms of poisoning may take some time (up to 24 hours) tomake their appearance and the following is suggested:1. Give complete rest for 1-2 days, during which the patient must be kept quiet and warm.2. Should the patient suffer from vomiting or increased blood sugar, appropriate solu-

tions should be administered. Treatment with oxygen breathing equipment is rec-ommended, as is the administration of cardiac and circulatory stimulants.

In cases of severe poisoning (intensive care unit recommended):1. Where pulmonary edema is observed, steroid therapy should be considered and

close medical supervision is recommended. Blood transfusions may be necessary.2. In case of manifest pulmonary edema, venesection should be performed under

vein pressure control. Heart glycosides (I.V.) can be used in case of hemocon-centration. Venesection may result in shock. Upon progressive edema of lungs,immediate intubation with a constant removal of edema fluid and oxygen over-pressure respiration, as well as measures required for shock treatment are rec-ommended. In case of kidney failure, extracorporeal hemodialysis is necessary.There is no specific antidote known for this poisoning.

3. Mention should be made here of suicidal attempts by taking solid aluminumphosphide by the mouth. After swallowing, emptying of the stomach by vomiting,flushing of the stomach with diluted potassium permanganate solution or a solu-tion of magnesium peroxide until flushing liquid ceases to smell of carbide, is rec-ommended. Thereafter, apply medicinal charcoal.

3. PRODUCT INFORMATION

FUMITOXIN® tablets and pellets are used to protect stored commodities fromdamage by insects. In limited areas, applications of FUMITOXIN may be made tocontrol burrowing vertebrate pests. For a list of approved burrowing rodent applica-tion sites see Section 26.1.FUMITOXIN metal phosphide fumigants are acted upon by atmospheric moisture toproduce phosphine gas. FUMITOXIN tablets and pellets contain aluminum phosphide (AlP) as their activeingredient and will liberate phosphine via the following chemical reaction:

AlP + 3H2O ---> Al(OH)3 + PH3

Phosphine gas is highly toxic to insects, burrowing pests, humans, and other forms of ani-mal life. In addition to its toxic properties, the gas will corrode certain metals and may ignitespontaneously in air at concentrations above its lower flammable limit of 1.8% v/v (18,000ppm). These hazards will be described in greater detail later on in this Applicator’s Manual.

3

FUMITOXIN also contains ammonium carbamate, which liberates ammonia and car-bon dioxide as follows:

NH2C00NH4 ---> 2NH3 + CO2These gases are essentially non-flammable and act as inerting agents to reduce firehazards.

FUMITOXIN is prepared in two spherical shapes. The rounded tablets weighapproximately 3 grams and will release 1 gram of phosphine gas. They are about16mm in diameter. The pellets are about 10 mm in diameter, weigh approximately0.6 gram and release 0.2 gram of phosphine gas.

FUMITOXIN Tablets are provided in 21kg cases, contain 14 resealable, gas-tightflasks of 500 tablets each or 70 flasks of 100 tablets each.

FUMITOXIN Pellets are provided in 21kg cases containing 14 resealable, gas-tightflasks of 1660 pellets each or 14 flasks of 2490 pellets each.

Upon exposure to air, FUMITOXIN pellets and tablets begin to react with atmos-pheric moisture to produce small quantities of phosphine gas. These reactions startslowly, gradually accelerates and then tapers off again as the aluminum phosphideis spent. FUMITOXIN pellets react somewhat faster than do the tablets. The ratesof decomposition of the tablets and pellets will vary depending upon moisture andtemperature conditions. For example, when moisture and temperature of the fumi-gated commodity are high, decomposition of FUMITOXIN may be complete in lessthan 3 days. However, at lower ambient temperatures and humidity levels, decom-position of FUMITOXIN may require 5 days or more. After decomposition, FUMI-TOXIN leaves a gray-white powder composed almost entirely of aluminum hydrox-ide and other inert ingredients. This will cause no problems if the fumigant has beenadded directly to a commodity such as grain. However, the spent powder must beretrieved for disposal after space fumigations. If properly exposed, the spent FUMI-TOXIN will normally contain only a small amount of unreacted aluminum phosphideand may be disposed of without hazard. While spent FUMITOXIN is not considereda hazardous waste, partially spent residual dusts from incompletely exposed FUMI-TOXIN will require special care. Precautions and instructions for further deactivationand disposal will be given under Section 28 of this Manual.

FUMITOXIN tablets and pellets are supplied in gas-tight containers and their shelflife is unlimited as long as the packaging remains intact. Once opened for fumiga-tion, the aluminum flasks of tablets or pellets may be tightly resealed and stored forfuture use. Storage and handling instructions will be given in detail under Section 19of this Manual.

4. PRECAUTIONARY STATEMENTS

4.1 Hazards to Humans and Domestic AnimalsDANGER: Aluminum phosphide from FUMITOXIN tablets, pellets or dust may befatal if swallowed. Do not get in eyes, on skin or on clothing. Do not eat, drink orsmoke while handling aluminum phosphide fumigants. If a sealed container is

4

opened, or if the material comes into contact with moisture, water or acids, theseproducts will release phosphine, which is an extremely toxic gas. If a garlic odor isdetected, refer to the Industrial Hygiene Monitoring instructions found in Section 15.6of this manual for appropriate monitoring procedures. Pure phosphine gas is odor-less; the garlic odor is due to a contaminant. Since the odor of phosphine may notbe detected under some circumstances, the absence of a garlic odor does not meanthat dangerous levels of phosphine gas are not present. Observe proper re-entryprocedures specified under Section 15.4 in this labeling to prevent over-exposure.

4.2 Environmental HazardsThis product is very highly toxic to wildlife. Non-target organisms exposed tophosphine gas will be killed. Do not apply directly to water or wetlands(swamps, bogs, marshes, and potholes). Do not contaminate water by clean-ing of equipment or disposal of wastes.

4.3 Physical and Chemical HazardsAluminum phosphide in tablets, pellets and partially spent dust will releasephosphine if exposed to moisture from the air or if it comes into contact withwater, acids and many other liquids. Since phosphine may ignite sponta-neously at levels above its lower flammable limit of 1.8% v/v (18,000 ppm), itis important not to exceed this concentration. Ignition of high concentrationsof phosphine can produce a very energetic reaction. Explosion can occurunder these conditions and may cause severe personal injury. Never allowthe buildup of phosphine to exceed explosive concentrations. Do notconfine spent or partially spent aluminum phosphide fumigants as the slowrelease of phosphine from this material may result in formation of an explo-sive atmosphere. Aluminum phosphide tablets and pellets, outside their con-tainers, should not be stacked or piled up or contacted with liquid water. Thismay cause a temperature increase, accelerate the rate of gas production andconfine the gas so that ignition could occur. It is preferable to open containersof aluminum phosphide products in open air as under certain conditions, theymay flash upon opening. Containers may also be opened near a fan or otherappropriate ventilation that will rapidly exhaust contaminated air. When open-ing, invert the container several times then point the container away from theface and body and slowly loosen the cap. Although the chances for a flash arevery remote, never open these containers in a flammable atmosphere. Theseprecautions will also reduce the fumigator’s exposure to phosphine gas. Ifcontainers are opened inside the structure to be fumigated, air monitoringmust be conducted to ensure worker’s exposure to phosphine gas does notexceed the allowable limit of 8-hour Time Weighted Average (TWA) of 0.3 ppmor the 15-minute Short-Term Exposure Limit (STEL) of 1.0 ppm phosphine.Pure phosphine gas is practically insoluble in water, fats and oils, and is stable atnormal fumigation temperatures. However, it may react with certain metals andcause corrosion, especially at higher temperatures and relative humidities. Metalssuch as copper, brass and other copper alloys, and precious metals such as goldand silver are susceptible to corrosion by phosphine. Thus, small electric motors,smoke detectors, brass sprinkler heads, batteries and battery chargers, fork lifts,temperature monitoring systems, switching gears, communication devices, com-puters, calculators and other electrical equipment should be protected or removed

5

before fumigation. Phosphine gas will also react with certain metallic salts and,therefore, sensitive items such as photographic film, some inorganic pigments,etc., should not be exposed. Immediately after addition of phosphine to the struc-ture, turn off any lights and unessential electrical equipment.

FUMITOXIN tablets and pellets are Restricted Use Pesticides due to the highacute inhalation toxicity of phosphine gas.Read and follow the complete label which contains instructions for the safeuse of this product. Additional copies are available from:

DEGESCH AMERICA, INC. PESTCON SYSTEMS DIV.153 TRIANGLE DRIVE 1808 FIRESTONE PARKWAYP. O. BOX 116 WILSON, NC 27893-7991WEYERS CAVE, VA 24486 USA Tel.: (252)237-7923/1-800-548-2778Tel.: (540)234-9281/1-800-330-2525 Fax: (252)243-1832Fax: (540)234-8225 Internet: www.pestcon.comInternet: www.degeschamerica.com


5. PESTS CONTROLLED

FUMITOXIN has been found effective against vertebrate and the following: (insectsand their preadult stages – that is, eggs, larvae and pupae:

INSECTSalmond moth European grain moth Mediterranean flour mothAngoumois grain moth flat grain beetle pink bollwormbean weevil fruit flies raisin mothbees granary weevil red flour beetlecadelle greater wax moth rice weevilcereal leaf beetle hairy fungus beetle rusty grain beetlecigarette beetle Hessian fly saw-toothed grain beetle confused flour beetle Indian meal moth spider beetlesdermestid beetles Khapra beetle tobacco mothdried fruit beetle lesser grain borer yellow mealwormdried fruit moth maize weevil Africanized bees &pea weevil honeybees infested

with tracheal mitesVERTEBRATE PESTSWoodchucksYellowbelly marmots (rockchucks)Prairie dogs (except Utah prairie dogs, Cynomys Parvidens)Norway ratsRoof ratsMiceGround squirrelsMolesVoles

6

Pocket gophersChipmunks

Although it is possible to achieve total control of the listed insect pests, this is fre-quently not realized in actual practice. Factors contributing to less than 100% con-trol are leaks, poor gas distribution, unfavorable exposure conditions, etc. In addi-tion, some insects are less susceptible to phosphine than others. If maximum con-trol is to be attained, extreme care must be taken in sealing, higher dosages mustbe used, exposure periods lengthened, proper application procedures followed, andtemperature and humidity conditions must be favorable.

6. COMMODITIES WHICH MAY BE FUMIGATED WITH FUMITOXIN

FUMITOXIN may be used for the fumigation of listed raw agricultural commodities,animal feed and feed ingredients, processed foods, tobacco and certain other non-food items when their commodity temperature is above 40°F(5° C).

6.1 Raw Agricultural Commodities, Animal Feed and Feed IngredientsFUMITOXIN tablets and pellets may be added directly to animal feed, feedingredients and raw agricultural commodities stored in bulk. For these com-modities not stored in bulk, FUMITOXIN may be placed in moisture permeableenvelopes, on trays, etc., and fumigated as with processed foods.

Raw Agricultural Commodities and Animal Feed and Feed IngredientsWhich May Be Fumigated with FUMITOXIN

almonds flower seed sesame seedanimal feed & feed ingredients grass seed seed & pod vegetablesbarley millet sorghumBrazil nuts oats soybeanscashews peanuts sunflower seedscocoa beans pecans triticalecoffee beans pistachio nuts vegetable seedcorn popcorn walnutscottonseed rice wheatdates ryefilberts safflower seed

6.2 Processed FoodsProcessed foods may be fumigated with FUMITOXIN. Under no condition shallany processed food or bagged commodity come in contact with FUMITOXINtablets, pellets or residual dust except that FUMITOXIN may be added directly toprocessed brewer’s rice, malt and corn grits for use in the manufacture of beer.

Processed Foods Which May Be Fumigated With FUMITOXIN

processed candy and sugarcereal flours and bakery mixescereal foods (including cookies, crackers, macaroni, noodles, pasta, pretzels, snack foods

and spaghetti)

7

processed cereals (including milled fractions and packaged cereals)processed oats (including oatmeal)cheese and cheese byproductschocolate and chocolate products (such as assorted chocolate, chocolate liquor, cocoa, cocoa powder, dark chocolate coating and milk chocolateproducts)processed coffeecorn gritscured, dried and processed meat products and dried fishdates and figsdried eggs and egg yolk solidsdried milk, dried powdered milk, non-dairy creamers and non-fat dried milkdried or dehydrated fruits (such as apples, dates, figs, peaches, pears, prunes, raisins,

citrus and sultanas)processed herbs, spices, seasonings and condimentsmaltprocessed nuts (such as almonds, apricot kernels, brazil nuts, cashews, filberts,

macadamia nuts, peanuts, pecans, pistachio nuts, walnuts and other processed nuts)soybean flour and milled fractionsprocessed teadried and dehydrated vegetables (such as beans, carrots, lentils, peas, potato flour, potato

products and spinach)yeast (including primary yeast)rice (brewer’s rice grits, enriched and polished)wild riceother processed foods

6.3 Non-Food Commodities Including TobaccoThe listed non-food items that may be fumigated with FUMITOXIN tablets, pel-lets or residual dust should not contact tobacco and certain other of the non-food commodities.

Non-Food Commodities Which May Be Fumigated with FUMITOXIN

processed or unprocessed cotton, wool and other natural fibers or clothclothingstraw and hayfeathershuman hair, rubberized hair, vulcanized hair, and mohairleather products, animal hides and furstobaccotires (for mosquito control)wood, cut trees, wood chips, wood and bamboo productspaper and paper productsdried plants and flowersseeds (such as grass seed, ornamental herbaceous plant seed and vegetable seed)other non-food commodities

8

7. EXPOSURE CONDITIONS FOR ALL FUMIGATIONS

The following table may be used as a guide in determining the minimum length ofthe exposure period at the indicated temperatures:

Minimum Exposure Periods for FUMITOXIN Temperature Pellets Tablets

40°F (5°C) Do not fumigate Do not fumigate41°-53°F (5-12°C) 8 days (192 hours) 10 days (240 hours)54°-59°F (12-15°C) 4 days (96 hours) 5 days (120 hours)60°-68°F (16-20°C) 3 days (72 hours) 4 days (96 hours)above 68°F (20°C) 2 days (48 hours) 3 days (72 hours)

The fumigation must be long enough so as to provide for adequate control of the insectpests that infest the commodity being treated. Additionally, the fumigation periodshould be long enough to allow for more or less complete reaction of FUMITOXIN withmoisture so that little or no unreacted aluminum phosphide remains. This will minimizeworker exposures during further storage and/or processing of the treated bulk com-modity as well as reduce hazards during the disposal of partially spent aluminumphosphide products remaining after space fumigations. The proper length of the fumi-gation period will vary with exposure conditions since, in general, insects are more dif-ficult to control at lower temperatures, and the rate of hydrogen phosphide gas pro-duction by FUMITOXIN is lower at lower temperatures and humidities.It should be noted that there is little to be gained by extending the exposure period if thestructure to be fumigated has not been carefully sealed or if the distribution of gas is poorand insects are not subjected to lethal concentrations of phosphine. Careful sealing isrequired to ensure that adequate gas levels are retained and proper application proce-dures must be followed to provide satisfactory distribution of phosphine gas. Application ofadditional FUMITOXIN is recommended if phosphine concentrations drop below an effec-tive level. If re-entry into the treated structure is required, follow the requirements for man-power and respiratory protection usage found under Section 10 in this manual. Somestructures can only be treated when completely tarped while others cannot be properlysealed by any means and should not be fumigated. Exposure times must be lengthenedto allow for penetration of gas throughout the commodity when fumigant is not uniformlyadded to the commodity mass, for example, by surface application or shallow probing. Thisis particularly important in the fumigation of bulk commodity contained in large storages.Remember, exposure periods recommended in the table are minimum periods andmay not be adequate to control all stored products pests under all conditions nor willthey always provide for total reaction of FUMITOXIN.It is permissible and often desirable to use a low-flow recirculation system for phos-phine gas in certain bulk storages. This method may be used in ship’s holds, vari-ous types of flat storage and vertical storage bins. Recirculation usually involves theapplication of fumigant to the surface of the commodity. The phosphine gas is thencontinuously or intermittently drawn out of the over space and blown into the bottomof the storage using specially designed low volume fans and ductwork. This methodfacilitates the quick and uniform penetration of phosphine throughout the commod-ity. In some instances a reduced dosage may be used. Please contact DegeschAmerica, Inc. if assistance is required in designing the recirculation system.

9

8. DOSAGE RATES FOR COMMODITIES & BURROWING PESTS

Phosphine is a mobile gas and will penetrate to all parts of the storage structure.Therefore, dosage must be based upon the total volume of the space being treatedand not on the amount of commodity it contains. The same amount is required totreat a 30,000-bushel silo whether it is empty or full of grain unless, of course, a tar-paulin seals off the surface of the commodity. The following dosage ranges areguidelines for bulk (per 1,000 bushels) and space (per 1,000 cu.ft.) fumigations:

8.1 Maximum Allowable Dosages for Fumigation with FUMITOXIN

Product per 1000 cu.ft.* per 1000 bu.*Pellets 725 900Tablets 145 180

*NOTE: Maximum Dosage for dates, nuts & dried fruits is 200 pellets, 40tablets/1000 cu.ft. OR 250 pellets/50 tablets/1000 bu.

Maximum allowable dosage rate for Rodent Burrows is 20 pellets perburrow OR 4 tablets per burrow.

The above dosages are not to be exceeded. It is important to be aware that a shortenedexposure period cannot be fully compensated for with an increased dosage of phosphine.Somewhat higher dosages, not to exceed the maximum dosage, are usually recom-mended under cooler, drier conditions or where exposure periods are relatively short.However, the major factor in selection of dosage is the ability of the structure to hold phos-phine gas during the fumigation. A good illustration of this point is comparison of the lowdosages recommended to treat modern, well-sealed warehouses with the higher rangesused for poorly constructed buildings that cannot be sealed adequately. In certain otherfumigations, proper distribution of lethal concentrations of phosphine gas reaching allparts of the structure becomes a very important factor in dose selection. An examplewhere this may occur is in the treatment of grain stored in tall silos. Poor gas distributionfrequently results when the fumigant is added on top of the grain. In such cases, use of alow-flow recirculation system is recommended under these circumstances. Please con-tact Degesch America, Inc. if assistance is required in designing the recirculation system.

8.2 Advisory Dosages for Various Types of FumigationsOne (1) FUMITOXIN tablet or five (5) FUMITOXIN pellets will produce a con-centration of 25 parts per million (ppm) of phosphine gas (PH3) in a volumeof 1000 cubic feet (1 gram PH3/1000 cu.ft. is equivalent to 25 ppm).

When a dosage range is listed, use the higher rate under conditions of severeinfestation, lower temperature and other applicable variables.

Do not exceed the maximum allowable rates specified above in Section 8.1.

10

Dosage Range____________ Type of Fumigation Pellets Tablets

1. Vertical Storages (such as 200-900/1000 bu. 40-180/1000 bu.silos, concrete bins, steel 150-700/1000 cu.ft. 30-140/1000 cu.ft.bins, etc.)

2. Farm Bins (Butler Type) 450-900/1000 bu. 90-180/1000 bu.350-725/1000 cu.ft. 70-145/1000 cu.ft.

3. Bulk stored commodities in 450-900/1000 bu. 90-180/1000 bu.flat storage, bunkers and 350-725/1000 cu.ft. 70-145/1000 cu.ft.commodities stored on groundloosely piled under gas tightcovering.

4. Packaged commodities (bagged 150-450/1000 cu.ft. 30-90/1000 cu.ft.grain, process foods, etc.)in sealable enclosures.

5. Nuts, dates or dried fruit 100-200/1000 cu.ft. 20-40/1000 cu.ft.in storage boxes.

6. Nuts, dates or dried fruit 125-250/1000 bu. 25-50/1000 bu.in bulk. 100-200/1000 cu.ft. 20-40/1000 cu.ft.

7. Railcars, containers, trucks, 225-500/1000 cu.ft. 45-145/1000 cu.ft.vans and other transportvehicles.

8. Space fumigation such as 100-300/1000 cu.ft. 20-60/1000 cu.ft.cereal mills, feed mills, foodprocessing plants & warehouses

9. Stored Tobacco 100-250/1000 cu.ft 20-50/1000 cu.ft

10. Non-food products 150-450/1000 cu.ft 30-90/1000 cu.ft.

11. Stored beehives, supers and 150-225/1000 cu.ft 30-45/1000 cu.ftother beekeeping equipment forwax moth control and Africanized honeybees with tracheal mites and foulbrood.

12. Barges 300-900/1000 bu. 60-80/1000 bu.250-725/1000 cu.ft. 50-145/1000 cu.ft.

13. Shipholds 200-400/1000 bu. 40-80/1000 bu.150-330/1000 cu.ft. 30-66/1000 cu.ft.

11

Higher dosages should be considered in structures that are of loose constructionand in the fumigation of bulk stored commodities in which diffusion will be slowedand result in poor distribution of hydrogen phosphide gas.

9. PROTECTIVE CLOTHING

GLOVES:

Wear dry gloves of cotton or other material if contact with tablets, pellets or dust islikely.

Gloves should remain dry during use.

Wash hands thoroughly after handling aluminum phosphide products.

Aerate used gloves and other clothing that may be contaminated in a well-ventilatedarea prior to laundering.

10. RESPIRATORY PROTECTION

10.1 When Respiratory Protection Must Be WornRespiratory protection is required when concentration levels of phosphine areunknown or when concentrations exceed permissible exposure limits.

10.2 Permissible Gas Concentration Ranges for Respiratory Protection DevicesA NIOSH/MSHA approved full-face gas mask – phosphine canister combinationmay be used at levels up to 15 ppm or following manufacturers use condition instruc-tions for escape. Above 15 ppm or in situations where the phosphine concentrationis unknown, a NIOSH/MSHA approved, SCBA must be worn. The NIOSH/OSHAPocket Guide DHHS (NIOSH) 97-140 or the NIOSH ALERT – PreventingPhosphine Poisoning and Explosions During Fumigation, lists these and other typesof approved respirators and the concentration limits at which they may be used.

10.3 Requirements for Availability of Respiratory ProtectionIf FUMITOXIN is to be applied from within the structure to be fumigated, anapproved full-face gas mask – phosphine canister combination or SCBA or itsequivalent must be available at the site of application in case it is needed.Respiratory protection must also be available for applications from outside thearea to be fumigated such as addition of tablets or pellets to automatic dis-pensing devices, outdoor applications, etc.

11. REQUIREMENTS FOR CERTIFIED APPLICATOR TO BE PRESENT ANDRESPONSIBLE FOR ALL WORKERS AS FOLLOWS:

A. A Certified Applicator must be physically present, responsible for, and maintainvisual and/or voice contact with all fumigation workers during the application of thefumigant, and also during the opening of the product containers. Once the applica-tion is complete and the structure has been made secure the certified applicatordoes not need to be physically present at the site.

12

B. A Certified Applicator must be physically present, responsible for, and maintainvisual and/or voice contact with all fumigation workers during the initial opening ofthe fumigation structure for aeration. Once the aeration process is secured andmonitoring has established that aeration can be completed safely the certified appli-cator does not need to be physically present and trained person(s) can complete theprocess and remove the placards.

C. Persons with documented training in the handling of phosphine products mustbe responsible for receiving, aerating and removal of placards from vehicles, whichhave been fumigated in transit. Refer to Section 12 for training requirements.

12. TRAINING REQUIREMENTS FOR RECEIPT OF IN-TRANSIT VEHICLES UNDERFUMIGATION

The trained person(s) must be trained by a Certified Applicator following the EPAaccepted product applicator’s manual that must precede or be attached to the out-side of a transport vehicle; or by other training which is accepted by local and/orstate authorities. When training has been completed and the employee demon-strates safety knowledge proficiency, the training date must be logged and main-tained in the employee’s safety training record for a minimum of three years.Refresher training must be done on an annual basis.

This training must cover the following items, each of which may be found in this manual:

a. How to aerate the vehicle and verify that it contains no more than 0.3 ppm phosphine.OR

b. How to transfer the commodity to another storage area without prior aeration andensure that worker safety limits are not being exceeded during the transfer.

c. How to determine when respiratory protection must be worn.

d. How to protect workers and nearby persons from exposure to levels above the8-hour Time Weighted Average (TWA) of 0.3 ppm or the 15 minute Short-TermExposure Limit (STEL) of 1.0 ppm phosphine.

e. Proper removal of placards from the vehicle.

f. How to follow proper residual disposal instructions.

13. GAS DETECTION EQUIPMENT

There are a number of devices on the market for the measurement of phosphine gasat both industrial hygiene and fumigation levels. Glass detection tubes used in con-junction with the appropriate hand-operated air sampling pumps are widely used.These devices are portable, simple to use, do not require extensive training and arerelatively rapid, inexpensive and accurate. Electronic devices are also available forboth low level and high phosphine gas readings. Such devices should be used in fullcompliance with manufacturers’ recommendations.

13

14. NOTIFICATION REQUIREMENTS

14.1 Authorities and On-Site Workers:As required by local regulations, notify the appropriate local officials (firedepartment, police department, etc.) of the impending fumigation. Provide tothe officials an MSDS and complete label for the product and any other tech-nical information deemed useful. Offer to review this information with the localofficial(s).

14.2 Incidents Involving These Products:Registrants must be informed of any incident involving the use of this product.Please call Degesch America, Inc. (540)234-9281/1-800-330-2525 or PestconSystems Div. (252)237-7923/1-800-548-2778 so the incident can be reportedto Federal and State Authorities.

14.3 Theft of Products:Immediately report to the local police department thefts of metal phosphidefumigants.

15. APPLICATOR AND WORKER EXPOSURE

Approved respiratory protection must be worn if concentrations exceed the allow-able limits, or when concentrations are unknown.

15.1 Exposure LimitsExposures to phosphine must not exceed the 8-hour time-weighted average(TWA) of 0.3 ppm or the 15 minute short-term exposure limit (STEL) of 1.0ppm phosphine. All persons are covered by these exposure standards.

15.2 Application of FumigantAt least two persons, a certified applicator and trained person, or two trained personsunder the direct supervision of the certified applicator must be present when entryinto the structure for application of the fumigant is required. Depending upon temper-ature and humidity, FUMITOXIN tablets and pellets release phosphine gas slowlyupon exposure to moisture from the air. In most cases, this release is slow enoughto permit applicators to deposit fumigant in the desired areas and then vacate thepremises without significant exposure to the gas. Monitoring must be conducted inorder to characterize the application and determine the fumigator’s exposure.

15.3 Leakage from Fumigated SitesPhosphine gas is highly mobile and given enough time may penetrate seem-ingly gas-tight materials such as concrete and cinderblock. Therefore, adja-cent, enclosed areas likely to be occupied must be examined to ensure thatsignificant leakage has not occurred. Sealing of the fumigated site and/or air-flow into the occupied areas must be sufficient to bring down the phosphineconcentration to a safe level of 0.3 ppm or below.

14

15.4 Aeration and Re-entryIf the structure is to be entered after fumigation, it must be aerated until thelevel of phosphine gas is 0.3 ppm or below. The area or site must be moni-tored to ensure that liberation of gas from the treated commodity does notresult in the development of unacceptable levels (i.e., over industrial hygienelevels of phosphine). Do not allow re-entry into treated areas by any personbefore the level of phosphine reaches 0.3 ppm or below unless protected byan approved respirator.

15.5 Handling Unaerated Commodities Transfer of incompletely aerated commodity via bulk handling equipment suchas augers, drag conveyors and conveyor belts to a new storage structure ispermissible. A Certified Applicator is responsible for training workers who han-dle the transfer of incompletely aerated listed commodities, and appropriatemeasures must be taken (i.e., ventilation or respiratory protection) to preventexposures from exceeding the exposure limits for phosphine. The new storage structure must be placarded if it contains more than 0.3 ppmphosphine. If the fumigation structure must be entered to complete the trans-fer, at least two trained persons, wearing proper respiratory protection, mayenter the structure. A certified applicator must be physically present during theentry into the structure.

REMEMBER transporting containers or vehicles under fumigation over publicroads is prohibited.

15.6 Industrial Hygiene MonitoringPhosphine exposures must be documented in an operations log or manual ateach fumigation area and operation where exposures may occur. Monitor air-borne phosphine concentrations in all indoor areas to which fumigators andother workers have had access during fumigation and aeration. Perform suchmonitoring in workers’ breathing zones. This monitoring is mandatory and isperformed to determine when and where respiratory protection is required.Once exposures have been adequately characterized, spot checks must bemade, especially if conditions change significantly or if an unexpected garlicodor is detected or a change in phosphine level is suspected.

15.7 Engineering Controls and Work PracticesIf monitoring shows that workers may be exposed to concentrations in excessof the permitted limits, then engineering controls (such as forced air ventila-tion) and/or appropriate work practices must be used to reduce exposure towithin permitted limits. Appropriate respiratory protection must be worn ifphosphine exposure limits are exceeded or concentrations are unknown.

16. PLACARDING OF FUMIGATED AREAS

All entrances to the fumigated area must be placarded including areas containingrodent burrows being fumigated (See Section 26.1). Placards must be made of sub-stantial material that can be expected to withstand adverse weather conditions, andmust bear the wording as follows:

15

1. The signal words DANGER/PELIGRO and the SKULL AND CROSSBONESsymbol in red.

2. The statement, “Structure and/or commodity under fumigation. DO NOTENTER/NO ENTRE”.

3. The statement, “This sign may only be removed by a certified applicator or a per-son with documented training after the structure and/or commodity is completelyaerated (contains 0.3 ppm or less of phosphine gas).”

If incompletely aerated commodity is transferred to a new storage structure, thenew structure must also be placarded if it contains more than 0.3 ppm. Workersexposure during this transfer must not exceed allowable limits.

4. The date the fumigation begins.

5. Name and EPA registration number of fumigant used.

6. Name, address and telephone number of the Fumigation Company and/or applicator.

7. A 24-hour emergency response telephone number.

All entrances to a fumigated area must be placarded. Where possible, place plac-ards in advance of the fumigation to keep unauthorized persons away. For railroadhopper cars, placards must be placed on both sides of the car near the ladders andnext to the top hatches into which the fumigant is introduced.Do not remove placards until the treated commodity or area is aerated down to 0.3 ppmhydrogen phosphide or less. To determine whether aeration is complete, each fumigatedstructure or transport vehicle must be monitored and shown to contain 0.3 ppm or lessphosphine gas in the air space around and, if feasible, in the mass of the commodity.

17. SEALING OF STRUCTURE

The structure to be fumigated must first be inspected to determine if it can be madesufficiently gas tight. Careful sealing is required so that adequate gas levels areretained. Turn off all ventilation, supply air, air conditioning, and any other air movingsystems which could negatively affect the fumigation. Thoroughly inspect the structureto be fumigated and seal cracks, holes and openings. These areas could include, butare not limited to: windows, doors, vents, chimneys and structural flaws. Sealing tech-niques can vary, but most often include polyethylene sheeting, adhesive tapes andadhesive sprays. Expandable foam or caulking material can work well on structuralflaws. Proper sealing will insure sufficient gas levels within the fumigated structure andwill decrease the chance of unwanted exposures outside of the fumigated area.As with all fumigations, it is required that sealing be inspected for leaks. If phosphineabove 0.3 ppm is found in an area where exposure to workers or bystanders mayoccur, the fumigator, using proper respiratory protective equipment must attempt toseal the leak from the exterior of the structure. Failing this, the fumigators, followingproper procedures to prevent accidental poisoning, may enter the structure and sealthe leaks from the interior. If the concentration inside the structure has decreased

16

below the target level as a result of the leakage, additional fumigant may be addedfollowing the sealing repairs.

DO NOT FUMIGATE A STRUCTURE THAT CANNOT BE SEALED SUFFICIENTLYGAS TIGHT.

18. AERATION OF FUMIGATED COMMODITIES

As an alternative to the aeration time periods listed below, each container ofthe treated commodity may be analyzed for residues using accepted analyti-cal methods.

18.1 Foods and FeedsTolerances for phosphine residues have been established at 0.1 ppm for ani-mal feeds and 0.01 ppm for processed foods. To guarantee compliance withthese tolerances, it is necessary to aerate these commodities for 48 hoursprior to offering them to the end consumer.

18.2 Non-Food CommoditiesAerate all non-food commodities to 0.3 ppm or less of phosphine. Monitordensely packed commodities to ensure that aeration is complete.

18.3 TobaccoTobacco must be aerated for at least three days (72 hours) when fumigated inhogsheads and for at least two days (48 hours) when fumigated in other contain-ers or until the concentration is below 0.3 ppm. When plastic liners are used, longeraeration periods may be required to aerate the commodity down to 0.3 ppm.

19. STORAGE INSTRUCTIONS

• Do not contaminate water, food or feed by storing pesticides in the same areasused to store these commodities.

• Store FUMITOXIN® in a dry, well-ventilated area away from heat, under lock andkey. Post as a pesticide storage area.

• Do not store FUMITOXIN® in areas where temperature may exceed 130°F• Do not store in buildings where humans or domestic animals may reside. Keep

out of reach of children.• FUMITOXIN® is supplied in gas-tight, resealable aluminum flasks. Do not

expose the product to atmospheric moisture any longer than is necessary andseal tightly before returning flasks to storage.

• The shelf life of FUMITOXIN® is virtually unlimited as long as the containers aretightly sealed.

19.1 Labeling of StorageThe labeling of the storage area should take into account the needs of a vari-ety of organizations. These should include, but not be limited to: company pol-icy, insurance carrier, Occupational Safety and Health Administration (OSHA),Emergency Planning and Community Right to Know and local emergencyresponse professionals. At a minimum, the storage must be marked with the

17

following signs and must be locked:1. Danger, Poison (with skull and cross bones)2. Authorized Personnel Only3. National Fire Protection Association (NFPA) Hazard Identification Symbols

for the pesticide.The NFPA has developed Hazard Identification Symbols. This standardizedsystem is designed to provide, at a glance, the information regarding thehealth, fire and reactivity hazards associated with hazardous materials. Thefollowing are the hazard categories and degree of hazard for aluminum phos-phide:

Category Degree of HazardHealth 4 (Severe Hazard)Flammability 4 (Severe Hazard)Reactivity 2 (Moderate)Special Notice Key W

NOTE: When using the NFPA Hazard Identification System, the characteristics ofall hazardous materials stored in a particular area must be considered. The local fireprotection district should be consulted for guidance on the selection and placementof such signs.

20. TRANSPORTATION INSTRUCTIONS

The United States Department of Transportation (DOT) classifies aluminum phos-phide as Dangerous When Wet material and it must be transported in accordancewith DOT regulations.

20.1 TRANSPORT DESIGNATIONS – The following transport designations applyto aluminum phosphide

Identification No.: UN 1397Proper Shipping Name: Aluminum phosphide Hazard Class: 4.3 (6.1)Packing Group: PG IShipping Label: Dangerous When Wet/PoisonShipping Placard: Dangerous When Wet

20.2 Transportation Special Permit:Degesch America, Inc. – Special Permit: DOT-SP11329Pestcon Systems Div. – Special Permit: DOT-SP10753Purpose and Limitation: “…The motor vehicles used under the terms of thisspecial permit are not required to be placarded…”

Modes of Transportation Authorized: Motor vehicle (Only private motor vehi-cles used in pest control operations are authorized to transport the packagescovered by the terms of this special permit.)

18

NOTE: You must have a copy of this special permit with you during transporta-tion. For a copy of this special permit contact:

DEGESCH AMERICA, INC. PESTCON SYSTEMS DIV.153 Triangle Drive 1808 Firestone ParkwayP. O. Box 116 Wilson, NC 27893-7991Weyers Cave, VA 24486 Tel.: (252)237-7923Tel.: (540)234-9281/1-800-330-2525 1-800-548-2778Internet: www.degeschamerica.com Internet: www.pestcon.com

21. REQUIRED WRITTEN FUMIGATION MANAGEMENT PLAN

The certified applicator is responsible for working with the owners and/or responsi-ble employees of the structure and/or area to be fumigated to develop and follow aFumigation Management Plan (FMP). State, county and local authorities may alsohave specific requirements. The FMP must be written PRIOR TO EVERY treatmentincluding fumigation treatment for burrowing pests. The FMP must address charac-terization of the structure and/or area, and include appropriate monitoring and noti-fication requirements, consistent with, but not limited to, the following:

1. For burrowing rodent applications: The use of this product is strictly prohib-ited within 100 feet of any building where humans and/or domestic animalsdo or may reside on single or multi-family residential properties and nurs-ing homes, schools (except athletic fields), daycare facilities and hospitals.For a list of approved burrowing application sites, see Section 26.1.

2. Inspect the structure and/or area to determine its suitability for fumigation.3. When sealing is required, consult previous records for any changes to the

structure, seal leaks and monitor any occupied adjacent buildings.4. Prior to each fumigation, review any existing FMP, MSDS, complete prod-

uct label and other relevant safety procedures with company officials andappropriate employees.

5. Consult company officials in the development of procedures and appropri-ate safety measures for nearby workers that will be in and around the areaduring application and aeration.

6. Consult with company officials to develop an appropriate monitoring planthat will confirm that nearby workers and bystanders are not exposed tolevels above the allowed limits during application, fumigation and aeration.This plan must also demonstrate that nearby residents will not be exposedto concentrations above the allowable limits.

7. Consult with company officials to develop procedures for local authoritiesto notify nearby residents in the event of an emergency.

8. Confirm the placement of placards to secure entrance into any area underfumigation.

9. Confirm the required safety equipment is in place and the necessary man-power is available to complete a safe and effective fumigation.

10. Written notification must be provided to the receiver of a vehicle that isfumigated in transit.

19

These factors must be considered in putting a FMP together. It is important to notethat some plans will be more comprehensive than others. All plans should reflect theexperience and expertise of the applicator and circumstances at and around thestructure and/or area.

In addition to the plan, the applicator must read the complete label which includes thecontainer label and Applicator’s Manual. Follow its directions carefully and abide by allthe restrictions. If the applicator has any questions about the development of a FMP con-tact DEGESCH AMERICA,INC. or PESTCON SYSTEMS DIV. for further assistance.The FMP and related documentation, including monitoring records, must be main-tained for a minimum of 2 years.

STEPS FOR PREPARATION OF THE REQUIRED WRITTEN FUMIGATION MANAGEMENT PLAN

Purpose

A Fumigation Management Plan (FMP) is an organized, written description of therequired steps involved to help ensure a safe, legal and effective fumigation. It will alsoassist you and others in complying with pesticide product label requirements. The guid-ance that follows is designed to help assist you in addressing all the necessary factorsinvolved in preparing for and fumigating a structure and/or area.

This guidance is intended to help you organize any fumigation that you might performPRIOR TO ACTUAL TREATMENT. It is meant to be somewhat prescriptive, yet flexibleenough to allow the experience and expertise of the fumigator to make changes based oncircumstances which may exist in the field. By following a step-by-step procedure, whichallow for flexibility, an effective fumigation may be performed.

Before any fumigation begins, carefully read and review the label which includes thecontainer label and Applicator’s Manual. This information must also be given to the appro-priate company officials (supervisors, foreman, safety officer, etc.) in charge of the site.Preparation is the key to any successful fumigation. If you do not find specific instructionsfor the type of fumigation that you are to perform listed in this Guidance Document you willwant to construct a similar set of procedures using this document as your guide or contactDEGESCH AMERICA, INC. or PESTCON SYSTEMS DIV. for assistance. Finally, beforeany fumigation begins you must be familiar with and comply with all applicable federal,state and local regulations. The success of the fumigation is not only dependent on yourability to do your job but also upon carefully following all rules, regulations, and proceduresrequired by governmental agencies.

A CHECKLIST GUIDE FOR A FUMIGATION MANAGEMENT PLAN

This checklist is provided to help you take into account factors that must be addressedprior to performing all fumigations. It emphasizes safety steps to protect people and prop-erty. The checklist is general in nature and cannot be expected to apply to all types of fumi-gation situations. It is to be used as a guide to prepare the required plan. Each item mustbe considered. However, it is understood that each fumigation is different and not all itemswill be necessary for each fumigation site.

20

A. PRELIMINARY PLANNING AND PREPARATION

1. Determine the purpose of the fumigationa. Elimination of insect infestationb. Elimination of vertebrate pestsc. Plant pest quarantine

2. Determine the type of fumigation. For example:a. Space: tarp, mill, warehouse, food plant or outdoor areab. Transport Vehicle: railcar, truck, van or containerc. Commodity: raw agricultural or processed foods or non-food d. Type of Storage: vertical silo, farm storage, flat storage, etc.e. Vessels: ship or barge. In addition to the Applicator’s Manual, read the

U.S. Coast Guard Regulation 46CFR Part 147A.f. Outdoor rodent burrows.

3. Fully acquaint yourself with the structure and commodity to be fumigated, including:a. The general structure layout, construction (materials, design, age, mainte-

nance), of the structure, fire or combustibility hazards, connecting struc-tures and escape routes, above and below ground and other unique haz-ards or structure characteristics. Prepare, with the owner/operator/personin charge, a drawing or sketch of structure to be fumigated, delineating fea-tures, hazards and other structural characteristics.

b. The number and identification of persons who routinely enter the area tobe fumigated (i.e., employees, visitors, customers, etc.)

c. The specific commodity to be fumigated, its mode of storage and its condition.d. The previous treatment history of the commodity, if available.e. Accessibility of utility service connections.f. Nearest telephone or other means of communication. Mark the location of

these items on the drawing/sketch.g. Emergency shut-off stations for electricity, water and gas. Mark the loca-

tion of these items on the drawing/sketch.h. Current emergency telephone numbers of local health, fire, police, hospi-

tal and physician responders.i. Name and phone number (both day and night) of appropriate company officials.j. Check, mark and prepare the points of fumigation application locations if

the job involves entry into the structure for fumigation.k. Review the entire label which includes both the container label and the

Applicator’s Manual.l. Exposure time considerations:

1. Product (tablets and pellets) to be used2. Minimum fumigation period, as defined and described by the label use

directions3. Down time required to be available4. Aeration requirements5. Cleanup requirements, including dry or wet deactivation methods,

equipment, and personnel needs, if necessary6. Measured and recorded commodity temperature and moisture

21

m. Determination of dosage:1. Cubic footage or other appropriate space/location calculations2. Structure sealing capability and methods3. Maximum allowable label dosage rates4. Temperature, humidity and wind5. Commodity/space volume6. Past history of fumigation of structure7. Exposure time

B. PERSONNEL1. Confirm in writing that all personnel in and around the structure and/or area to

be fumigated have been notified prior to application of the fumigant. Considerusing a checklist that each employee initials indicating they have been notified.

2. Instruct all fumigation personnel to read the Applicator’s Manual. Fumigationpersonnel must be trained in the proper method of application, the hazards thatmay be encountered and the selection of personal protection devices, includ-ing detection equipment.

3. Confirm that all personnel are aware of and know how to proceed in case of anemergency situation.

4. Instruct all personnel on how to report any accident and/or incidents related to fumi-gant exposure. Provide a telephone number for emergency response reporting.

5. Instruct all personnel to report to proper authorities any theft of fumigant and/orequipment related to fumigation.

6. Establish a meeting area for all personnel in case of an emergency.

C. MONITORING1. Safety

a. Monitoring of phosphine concentrations must be conducted in areas to pre-vent excessive exposure and to determine where exposure may occur.Document where monitoring will occur.

b. Keep a log or manual of monitoring records for each fumigation site. Thislog must, at a minimum, contain the timing, number of readings taken andlevel of concentrations found in each location.

c. When monitoring, document even if there is no phosphine present abovethe safe levels. In such cases, subsequent monitoring is not routinelyrequired. However, spot checks must be made occasionally, especially ifconditions change significantly.

2. Efficacy

a. For stationary structures, phosphine readings MUST be taken from within thefumigated structure to insure proper gas concentrations. If the phosphine con-centrations have fallen below the targeted level, the fumigators, following properentry procedures, may re-enter the structure and add additional product.

b. All phosphine concentration readings must be documented.

22

D. NOTIFICATION

1. Confirm the appropriate local authorities (fire departments, police departments,etc.) have been notified as per label instructions, local ordinances (if applica-ble), or instructions of the client.

2. Prepare written procedure (“Emergency Response Plan”), which containsexplicit instructions, names and telephone numbers so as to be able to notifylocal authorities if phosphine leve ls are exceeded in an area that could be dan-gerous to bystanders and/or domestic animals.

3. Confirm that the receiver of in-transit vehicles under fumigation have been noti-fied and are trained according to Section 12 of this Applicator’s Manual.

E. SEALING PROCEDURES

1. Sealing must be adequate to control the pests. Care should be taken to insurethat sealing materials would remain intact until the fumigation is complete.

2. If the structure has been fumigated before, review the previous FMP for pre-vious sealing information.

3. Make sure that construction/remodeling has not changed the building in amanner that will affect the fumigation.

4. Warning placards must be placed on every possible entrance to the fumiga-tion structure.

F. APPLICATION PROCEDURES & FUMIGATION PERIOD

1. Plan carefully and apply all fumigants in accordance with the label requirements.2. When entering into the area under fumigation, always work with two or more

people under the direct supervision of a certified applicator wearing appropri-ate respirators.

3. Apply fumigant from the outside where appropriate.4. Provide watchmen when the possibility of entry into the fumigated site by

unauthorized persons cannot otherwise be assured.5. When entering structures, always follow OSHA rules for confined spaces.6. Document that the receiver of vehicles fumigated in transit has been notified.7. Turn off any electric lights in the fumigated area of the structure, as well as all

non-essential electrical motors.

G. POST-APPLICATION OPERATIONS

1. Provide watchmen when the fumigation structure cannot be secured fromentry by unauthorized persons during the aeration process.

2. Aerate in accordance with structural limitations.3. Turn on ventilating or aeration fans where appropriate.4. Use a suitable gas detector before re-entry into a fumigated structure to deter-

mine fumigant concentration.5. Keep written records of monitoring to document completion of aeration.6. Consider temperature when aerating.7. Ensure that aeration is complete before moving a treated vehicle onto public roads.8. Remove warning placards when aeration is complete.

23

9. Inform business/client that employees/other persons may return to work orotherwise be allowed to re-enter the aerated structure.

22. APPLICATION PROCEDURES

A FMP must be written PRIOR to all applications.A FMP must be devised to cover application, exposure period, aeration anddisposal of the fumigant so as to keep to a minimum any human exposure tophosphine and to help assure adequate control of the insect pests.

22.1 Farm Bins:Leakage is the single most important cause of failures in the treatment of farmstorages. Since these storages are often small, they usually have a higherleakage area in proportion to their capacity. Most wooden storage structuresare so porous that they cannot be successfully fumigated unless they are com-pletely tarped. Do not fumigate a storage that will be entered by humans or ani-mals prior to aeration. Do not fumigate areas which house sensitive equipmentcontaining copper or other metals likely to be corroded by phosphine gas.

1. Read the label, Applicator’s Manual, MSDS and related safety material.

2. Inspect the bin to determine if you can fumigate effectively.

3. Develop an appropriate Fumigation Management Plan.

4. If the bin is located in an area where nearby workers and/or bystanders ordomestic animals would be exposed to phosphine gas because of leakagefrom the bin:(a) Develop a monitoring procedure that will confirm if leakage from the

bin is above the allowable limits in an area that would affect nearbyworkers or bystanders.

(b) Advise local authorities when and where you will be fumigating.Provide and review with them the MSDS, complete label and otherrelevant safety information.

5. If the bin is in an isolated area on private property (a) and (b) above arenot required.

6. Seal the bin as tightly as possible. It is recommended that the surface ofthe grain be covered with poly after FUMITOXIN has been applied. Tarpingthe grain surface will greatly reduce the leak rate of the gas as well asreduce the amount of FUMITOXIN required. Only the volume below thetarp must be dosed. If not tarped, the entire volume of the storage must betreated, whether full or empty.

7. Using the Applicator’s Manual, calculate the dosage of tablets or pellets tobe applied based on type of structure, its sealing properties, content type,expected weather conditions, commodity temperature, moisture content ofthe commodity, and the planned duration of the fumigation. (See Section 8)

24

8. FUMITOXIN tablets or pellets required for the fumigation may be scatteredover the surface or probed into the grain using a rigid PVC pipe about 5 to7 feet in length and having a diameter of 1-1/4 inches.

9. Use approximately 20-50 tablets or 100-250 pellets per probe. Probe thedosage uniformly over the surface. Fumi-Sleeve® dust retainer or pack-aged fumigants may be used if dust-free applications are desired.

10. Immediately cover the surface of the grain with a plastic tarpaulin.

11. Place no more than 25 percent of the total dose at the bottom if the bin isequipped with aeration fans. Caution: Make sure that the aeration duct isdry before adding FUMITOXIN. Addition of FUMITOXIN to water in an aer-ation duct may result in a fire.

12. Seal the aeration fan with 4-mil plastic sheeting.

13. Place placards on all entrances to the bin and near the ladder.

14. Following aeration of the bin, the surface of the grain may be sprayed withan approved protectant to discourage reinfestation.

Note: If monitoring equipment is not available, an approved canister respiratormust be worn during application from within an enclosed area.

22.2 Flat StoragesTreatments of these types of storages often require considerable time andphysical effort. Therefore, sufficient manpower should be available to completethe work rapidly enough to prevent excessive exposure to phosphine gas. Ventflasks outside the storage, conduct fumigations during cooler periods, andemploy other work practices to minimize exposures. It is likely that respiratoryprotection will be required during application of fumigant to flat storages. Referto the sections on Applicator and Worker Exposure and Respiratory Protection.

1. Inspect the site to determine its suitability for fumigation.

2. Determine if the structure is in an area where leakage during fumigation oraeration would adversely affect nearby workers or bystanders if concentra-tions were above the permitted exposure levels.


4. Consult previous records for any changes to the structure. Seal vents,cracks and other sources of leaks.

5. Using the Applicator’s Manual, determine the length of the fumigation andcalculate the dosage of tablets or pellets to be applied based upon volumeof the building, contents, air and/or commodity temperature and the gen-eral tightness of the structure.

25

6. Apply tablets or pellets by surface application, shallow probing, deep prob-ing or uniform addition as the flat storage is filled.Storages requiring more than 24 hours to fill should not be treated by addi-tion of fumigant to the commodity stream as large quantities of phosphinemay escape before the bin is completely sealed.Probes should be inserted vertically at intervals along the length and widthof the flat storage. Pellets or tablets may be dropped into the probe at inter-vals as it is withdrawn.Surface application may be used if the bin can be made sufficiently gastight to contain the fumigant gas long enough for it to penetrate the com-modity. In this instance, it is advisable to place about 25 percent of thedosage in the floor level aeration ducts. Check the ducts prior to additionof FUMITOXIN to make sure that they contain no liquid water.

7. Placement of plastic tarp over the surface of the commodity is often advis-able, particularly if the overhead of the storage cannot be well sealed.

8. Lock all entrances to the storage and post fumigation warning placards.

22.3 Vertical Storages (concrete upright bins and other silos in which grain can berapidly transferred)


2. Determine if the structure is in an area where leakage during fumigation oraeration would expose nearby workers or bystanders to concentrationsabove the permitted levels.


4. Consult previous records for any changes to the structure. Close openingsand seal cracks to make the structure as airtight as possible. Prior to thefumigation, seal the vents near the bin top and any openings which con-nect to adjacent bins.

5. Determine the length of the fumigation and calculate the dosage of tablets orpellets to be applied based upon volume of the building, air and/or commod-ity temperature and the general tightness of the structure. (See Section 8.2)

6. Tablets or pellets may be applied continuously by hand or by an automaticdispenser on the headhouse/gallery belt or into the fill opening as the com-modity is loaded into the bin. An automatic dispenser may also be used toadd FUMITOXIN into the commodity stream in the up leg of the elevator.Monitoring must be conducted during application to determine the need forrespiratory protection.

7. Seal the bin deck openings after the fumigation has been completed.

26

8. Bins requiring more than 24 hours to fill should not be fumigated by continu-ous addition into the commodity stream. Probing, surface application or otherappropriate means may be employed to fumigate these bins. Exposure peri-ods should be lengthened to allow for diffusion of gas to all parts of the bin ifFUMITOXIN has not been applied uniformly throughout the commodity mass.

9. Place warning placards on the discharge gate and on all entrances.

22.4 Mills, Food Processing Plants and Warehouses


2. Determine if the structure is in an area where leakage during fumigation oraeration would expose nearby workers or bystanders if concentrationswere above the permitted exposure levels.


4. Determine the length of the fumigation and calculate the dosage of tabletsor pellets to be applied based upon volume of the building, air and/or com-modity temperature and the general tightness of the structure. (SeeSection 8)

5. Read the directions found in 4.2 Physical and Chemical Hazards andremove or cover any of the listed items that can become damaged fromexposure to phosphine gas.

6. Consult previous records for any changes in the structure. Carefully sealand placard the space to be fumigated.

7. Place trays or sheets of Kraft paper or foil, up to 12 sq. ft. (1.1 sq. M) inarea, on the floor throughout the structure.

8. Spread FUMITOXIN on the sheets at a density no greater than 30 tabletsper sq. ft. or 150 pellets per sq. ft. This corresponds to slightly more thanone-half flask of tablets or one-half flask of pellets per 3'x 4' sheet. Checkto see that FUMITOXIN has not piled up and that it is spread out evenly tominimize contact between the individual tablets or pellets.

9. Turn off any lights within the treated area and shut off all electrical motorsnot essential to operations of the storage. Doors leading to the fumigatedspace must be closed, sealed and placarded with warning signs.

10. Upon completion of the exposure period, open windows, doors, vents, etc.Allow the fumigated structure to aerate. Do not enter the structure withoutproper Personal Protective Equipment (PPE) until gas readings have beentaken and the concentration is below the allowable limits. Gas concentra-tion readings may be taken using low-level detector tubes or similardevices to ensure safety of personnel who re-enter the treated area.

27

11. Collect the spent FUMITOXIN dust and dispose of it, with or without furtherdeactivation. Refer to Disposal Instructions in this manual.

12. Remove fumigation warning placards from the aerated structure.

22.5 Railcars, Containers, Trucks, Vans and Other Transport Vehicles

Develop an appropriate Fumigation Management Plan.

Railcars, containers, trucks, vans and other transport vehicles shipped piggy-back by rail may be fumigated in transit. However, the aeration of railcars, rail-road boxcars, containers and other vehicles is prohibited en-route. It is notlegal to move trucks, trailers, containers, vans, etc., over public roads or high-ways until they have been aerated.Transport vehicles loaded with bulk commodities, to which FUMITOXIN tablets orpellets may be added directly, are treated in essentially the same way as anyother flat storage facility. FUMITOXIN may be added as the vehicle is being filled.The dose may be scattered over the surface after loading has been completedor the tablets or pellets may be probed below the surface. Carefully seal anyvents, cracks or other leaks, particularly if the fumigation is to be carried out intransit. See Section 16 of this Applicator’s Manual for placarding requirements.

PHOSTOXIN Prepacs or Fumi-Cel® plates (not classified by UL) are recom-mended for the treatment of transport vehicles or similar storages containingprocessed foods for which no direct contact is allowed with tablets or pellets.

The shipper and/or the fumigator must provide written notification to thereceiver of railcars, railroad boxcars, shipping containers and other vehicleswhich have been fumigated in transit. A copy of the Applicator’s Manual mustprecede or accompany all transportation containers or vehicles which arefumigated in transit. If the Applicator’s Manual is sent with the transport vehi-cle it must be placed securely on the outside of the vehicle.Proper handling of treated railcars at their destination is the responsibility of theconsignee. Upon receipt of the railcar, railroad boxcars, shipping containers andother vehicles, a certified applicator and/or persons with documented authorizedtraining must supervise the aeration process and removal of the placards.

Do not use FUMITOXIN tablets or pellets in cars or other personal vehicles.

22.6 Tarpaulin and Bunker FumigationsUse of plastic sheeting or tarpaulins to cover commodities is one of the easiestand least expensive means for providing relatively gas tight enclosures whichare very well-suited for fumigation. Poly tarps are penetrated only very slowlyby phosphine gas and tight coverings are readily formed from the sheets. Thevolume of these enclosures may vary widely from a few cubic feet (for exam-ple, a fumigation tarpaulin placed over a small stack of bagged commodity) toa plastic bunker storage capable of holding 600,000 bushels of grain or more.

28

1. Develop an enclosure suitable for fumigation by covering bulk or packagedcommodities with poly sheeting. The sheets may be taped together to pro-vide a sufficient width of material to ensure that adequate sealing isobtained. If the flooring upon which the commodity rests is of wood or otherporous material, the commodity to be fumigated must be repositioned ontopoly prior to covering for fumigation. The plastic covering of the pile maybe sealed to the floor using sand or water snakes by shoveling soil or sandonto the ends of the plastic covering or by other suitable procedures. Thepoly covering must be reinforced by tape or other means around any sharpcorners or edges in the stack so as to reduce the risk of tearing. Thinnerpoly, about 2 mil, is suitable for most indoor tarp fumigations and for seal-ing of windows, doors and other openings in structures. However, 4 milpoly or thicker is more suitable for outdoor applications where wind or othermechanical stresses are likely to be encountered.

2. Determine if the enclosure is in an area where leakage during fumigationor aeration would affect nearby workers or bystanders.


4. Using the guidance given under Section 7, Exposure Conditions, deter-mine the length of the fumigation and calculate the dosage of tablets orpellets to be applied based upon volume of space under the tarp, air and/orcommodity temperature.

5. Tablets or pellets may be applied to the tarped stack or bunker storage of bulkcommodity through slits in the poly covering. Probing or other means of dosingmay be used. Avoid application of large amounts of FUMITOXIN at any onepoint. FUMITOXIN should be added below the surface of the commodity if con-densation or other source of moisture is likely to form beneath the poly. The slitsin the covering should be carefully taped to prevent loss of gas once the dosehas been applied and the introduction of water from rain. PHOSTOXIN Prepacs(not classified by UL) are recommended for the treatment of bagged commodi-ties and processed foods although tablets and pellets on trays or sheets of Kraftpaper may be used. Care should be taken to see that the poly is not allowed tocover the FUMITOXIN and prevent contact with moist air or confine the gas.

6. Distribution of phosphine gas is generally not a problem in the treatment ofbagged commodities and processed foods. However, fumigation of largerbunker storages containing bulk commodity will require proper applicationprocedures to obtain adequate results.

7. Place warning placards at conspicuous points on the enclosure.

22.7 In-Transit Shiphold Fumigation

Develop an appropriate Fumigation Management Plan.

29

22.7.1 General Information1. Important – In-transit ship or shiphold fumigation is also governed

by U.S. Coast Guard Regulation 46 CFR 147A, InterimRegulations for Shipboard Fumigation. Refer to this regulationprior to fumigation. For further information contact:

CommandantU.S. Coast GuardHazardous Materials Standards DivisionGMSO-3Washington, DC 20593-0001

22.7.2 Pre-Voyage Fumigation Procedures – A FMP must be written forall fumigations PRIOR TO ACTUAL TREATMENT.1. Prior to fumigating a vessel for in-transit cargo fumigation, the

master of the vessel, or his representative, and the certified appli-cator must determine whether the vessel is suitably designed andconfigured so as to allow for safe occupancy by the ship’s crewthroughout the duration of the fumigation. If it is determined thatthe vessel does not meet these requirements, then the vesselmust not be fumigated unless all crew members are removedfrom the vessel. The crew members are not permitted to re-occupy the vessel until it has been properly aerated and the mas-ter of the vessel and the certified applicator have made a deter-mination that the vessel is safe for occupancy.

2. The certified applicator must notify the master of the vessel, or hisrepresentative, of the requirements relating to personal protectionequipment*, detection equipment, and that a person qualified inthe use of this equipment must accompany any vessel containingcargo under fumigation. Emergency procedures, cargo ventila-tion, periodic monitoring and inspections, and first aid measuresmust be discussed with and understood by the master of the ves-sel or his representative.

*Note: Personal protection equipment means a NIOSH/MSHA approved res-pirator or gas mask fitted with an approved canister for phosphine. The can-ister is approved for use up to 15 ppm. SCBA or its equivalent must be usedabove 15 ppm or at unknown concentrations.

3. Seal all openings to the cargo hold or tank and lock or otherwisesecure all openings, manways, etc., which might be used to enterthe hold. The overspace pressure relief system of each tank aboardtankers must be sealed by closing the appropriate valves and seal-ing the openings into the overspace with gas-tight materials.

4. Placard all entrances to the treated spaces with fumigation warn-ing signs.

30

5. If the fumigation is not completed and the vessel aerated beforethe manned vessel leaves port, the person in charge of the vesselshall ensure that at least two units of personal protection equip-ment and one phosphine gas detection device, and a person qual-ified in their operation be on board the vessel during the voyage.

6. During the fumigation, or until a manned vessel leaves port or thecargo is aerated, the certified applicator shall ensure that a qualifiedperson using phosphine gas detection equipment tests spaces adja-cent to areas containing fumigated cargo as well as all regularlyoccupied spaces for fumigant leakage. If leakage of the fumigant isdetected, the person in charge of the fumigation shall take action tocorrect the leakage or shall inform the master of the vessel, or hisrepresentative, of the leakage so that corrective action can be taken.

7. Review with the master, or his representative, the precautions and pro-cedures to follow during the voyage of a shiphold in-transit fumigation.

22.7.3 Application Procedures for Bulk Dry Cargo Vessels and Tankers1. Apply tablets or pellets by scattering uniformly over the commod-

ity surface or they may be shallow or deep probed into the com-modity mass. Fumi-Sleeves® or packaged metal phosphides arerecommended if dust-free applications are desired.

2. Immediately after application of the fumigant, close and secure allhatch covers, tank tops, butterworth valves, manways, etc.

22.7.4 In-Transit Fumigation of Transport Units (Containers) AboardShipsIn-transit fumigation of transport units on ships is also governed byDOT RSPA 49 CFR 176.76(h) Transport Vehicles, Freight Containers,and Portable Tanks Containing Hazardous Materials and InternationalMaritime Dangerous Goods Code P9025-1 Amdt. 27-94.Application procedures for fumigation of raw commodities orprocessed foods in transport units (containers) are described inSection 22.5 of this manual.

22.7.5 Precautions and Procedures During Voyage1. Using appropriate gas detection equipment, monitor spaces adja-

cent to areas containing fumigated cargo and all regularly occu-pied areas for fumigant leakage. If leakage is detected, the areashould be evacuated of all personnel, ventilated, and action takento correct the leakage before allowing the area to be occupied.

2. Do not enter fumigated areas except under emergency conditions.If necessary to enter a fumigated area, appropriate personal pro-tection equipment must be used. Never enter fumigated areasalone. At least one other person wearing personal protection equip-ment should be available to assist in case of an emergency.

31

22.7.6 Precautions and Procedures During Discharge1. If necessary to enter holds prior to discharge, test spaces directly

above grain surface for fumigant concentration, using appropriategas detection and personal safety equipment. Do not allow entry tofumigated areas without personal safety equipment unless fumigantconcentrations are at safe levels, as indicated by a suitable detector.

23. BARGES

Barge fumigation is also regulated by U. S. Coast Guard Regulation 46 CFR Part147A as modified by U. S. Coast Guard Special Permit 2-75. This permit, whichmust be obtained prior to the fumigation, is available from:

CommandantU. S. Coast GuardHazardous Materials Standards Div.GMSO-3Washington, DC 20593-0001

Leaks are a common cause of failures in the treatment of commodities aboardbarges. Carefully inspect all hatch covers prior to application of FUMITOXIN andseal, if necessary. Placard the barge. Notify consignee if the barge is to be fumi-gated in transit and provide safety instructions for receipt and unloading.

24. SMALL SEALABLE ENCLOSURES

Develop an appropriate Fumigation Management Plan.Excellent results may be attained in the treatment of small enclosures since it isoften possible to control the temperature during fumigation and also to make theenclosure virtually gas tight. Take care not to overdose during these fumigations. Asingle FUMITOXIN pellet will treat a space of from 1.4 to 10 cubic feet and a singleFUMITOXIN tablet from 6.9 to 50 cubic feet.

25. BEEHIVES, SUPERS AND OTHER BEE KEEPING EQUIPMENT

Develop an appropriate Fumigation Management Plan.FUMITOXIN tablets and pellets may be used for the control of the Greater Wax Moth instored beehives, supers and other bee keeping equipment and for the destruction ofbees, Africanized bees and diseased bees including those infested with tracheal mitesand foulbrood. The recommended dosage for this use is 30-45 tablets or 150-225 pelletsper 1000 cubic feet.Fumigations may be performed in chambers at atmospheric pressure, under tarpau-lins, etc., by placing the tablets or pellets on trays or in moisture permeableenvelopes. Do not add more than 2 tablets or 10 pellets to each envelope. Honeyfrom treated hives or supers may only be used for bee food.

26. BURROWING PEST CONTROL

A Fumigation Management Plan must be written for all burrowing pests fumigations.

32

26.1 Use Restrictions:

THE USE OF THIS PRODUCT IS STRICTLY PROHIBITED WITHIN 100FEET OF ANY BUILDING WHERE HUMANS AND/OR DOMESTIC ANIMALSDO OR MAY RESIDE ON SINGLE OR MULTI-FAMILY RESIDENTIAL PROP-ERTIES AND NURSING HOMES, SCHOOLS (EXCEPT ATHLETIC FIELDS),DAYCARE FACILITIES AND HOSPITALS.

This product must be applied to underground burrow systems located in non-crop areas, crop areas, or orchards occupied by woodchucks, yellowbelly mar-mots (rockchucks), prairie dogs (except Utah prairie dogs, CynomysParvidens), Norway rats, roof rats, mice, ground squirrels, moles, voles, pocketgophers and chipmunks.

All treatments for control of these species in burrows must be made outdoors.Pellets or tablets must be applied directly to underground burrow systems.Before using FUMITOXIN tablets or pellets for burrowing pest control, readthe applicable restrictions under Environmental Hazards, EndangeredSpecies and Special Local Restrictions below.

This product must be used out-of-doors only for control of burrowing pests onagricultural areas, orchards, non-crop areas (such as pasture and rangeland),golf courses, athletic fields, airports, cemeteries, rights-of-ways, earthendams, parks and recreational areas, other non-residential institutional orindustrial sites and on residential or other commercial properties in accor-dance with the following directions:

1. This product must not be applied into a burrow system that is within 100feet of a building where humans and/or domestic animals do or may resideon single and multi-family residential properties and nursing homes,schools (except athletic fields), daycare facilities, hospitals and other com-mercial buildings that are regularly occupied.

2. When this product is used in athletic fields or parks, the applicator shall post asign at entrances to the treated site containing the signal word DANGER/PELIGRO, skull and crossbones, the words: DO NOT ENTER/NO ENTRE,FIELD NOT FOR USE, the name and EPA registration number of the fumigant.The sign must state a 24-hour emergency response number and the contactnumber of the certified applicator responsible for the application. Signs mustbe no smaller than 9 inches by 11 inches and must stand at least 18 incheshigh from ground. Signs must be made of substantial material that can beexpected to withstand adverse weather conditions and all information must belegible. Signs should remain posted for a minimum of 2 days after the finaltreatment and may be removed by the certified applicator or contracting party.

3. When this product is used out-of-doors on a site other than an athletic field orpark, the applicator shall post a sign at the application site containing the sig-nal word DANGER/PELIGRO, skull and crossbones, the words: DO NOTENTER/NO ENTRE, the name and EPA registration number of the fumigant.The sign must state a 24-hour emergency response number and the contactnumber of the certified applicator responsible for the application. Signs must

33

be no smaller than 9 inches by 11 inches and must stand at least 18 incheshigh from ground. Signs must be made of substantial material that can beexpected to withstand adverse weather conditions and all information must belegible. Signs should remain posted for a minimum of 2 days after the finaltreatment and may be removed by the certified applicator or contracting party.

DO NOT TREAT ANY BURROWS THAT OPEN UNDER OR INTO OCCU-PIED BUILDINGS. In addition, check for any other source through which thegas may enter into occupied buildings as a result of application to burrows. Ifthere is any way gas can move through pipes, conduits, etc. from burrows, donot treat these burrows.

Prior to treating a rodent burrow, the applicator must provide the customerwith a copy of the Fumigation Management Plan.

26.2 Application Directions for Control of Burrowing Pests

For use by a certified applicator or person under their direct supervision and whohave been trained specifically for use of this product in burrowing pest control.

Use application procedures appropriate to the type of burrow system being treated.DOSAGE RATES MUST NOT BE EXCEEDED UNDER ANY CIRCUMSTANCES.

26.2.1 For species with open burrow systems: locate all entrances to eachburrow system. Treatment of more than one entrance in a system isoften desirable as systems often overlap and are not defined. Treat allentrances except for those entrances you are sure connect to alreadytreated entrances. Insert 2 to 4 tablets or 10 to 20 pellets into eachentrance to be treated. Use the lower rates for smaller burrows and/orwhen soil moisture is high. Use higher rates for larger burrow systemsand when soil moisture is relatively low. Pack the treated entrance withcrumpled paper and shovel soil to cover the paper. Using crumpledpaper will prevent soil from covering the tablets or pellets and slowingdown their action. Rocks, clods of soil, cardboard, etc. may also be usedfor this purpose. Be sure to seal all untreated entrances by shovelingand packing soil and/or sod to completely seal the opening.

Inspect treated areas 1 or 2 days following treatment for signs ofresidual activity of target species. Treat all reopened burrows in thesame manner prescribed above.

THIS PRODUCT MUST NOT BE APPLIED INTO A BURROW SYSTEM THATIS WITHIN 100 FEET OF A BUILDING WHERE HUMANS AND/OR DOMES-TIC ANIMALS DO OR MAY RESIDE ON SINGLE AND MULTI-FAMILY RES-IDENTIAL PROPERTIES AND NURSING HOMES, SCHOOLS (EXCEPTATHLETIC FIELDS), DAYCARE FACILITIES, HOSPITALS AND OTHERCOMMERCIAL BUILDINGS THAT ARE REGULARLY OCCUPIED.

26.2.2 For species with closed burrow systems: (pocket gophers and molesin some situations). Locate the main underground runway by probing with

34

a smooth-sided rod 12 to 18 inches from a fresh mound. For pocketgophers, begin probing on the flat side of the mound. A sudden reductionin soil resistance to the probe indicates that the main runway has beenlocated. Once the main runway is located, remove the probe and apply 2to 4 tablets or 10 to 20 pellets through the probe hole. Adjust treatmentrate according to the level of soil moisture, using more pellets or tablets ifthe soil is relatively dry. Do not treat if soil is extremely dry or if there areno signs of recent gopher or mole activity. Make a tight seal to close probehole by using a clod of soil or a sod plug to cover the hole or by using theheel of your shoe to push sod and/or soil over the surface opening. If theprobe hole is more than one inch in diameter, place crumpled paper in thehole before closing it with soil and/or sod. Two days after treatment, youmay check area for residual pest activity by poking holes in main runwaysof burrow systems, flagging holes and inspecting them two days later.You should retreat all reclosed systems, on both sides of the plug.

THIS PRODUCT MUST NOT BE APPLIED INTO A BURROW SYSTEM THATIS WITHIN 100 FEET OF A BUILDING WHERE HUMANS AND/OR DOMES-TIC ANIMALS DO OR MAY RESIDE ON SINGLE AND MULTI-FAMILY RES-IDENTIAL PROPERTIES AND NURSING HOMES, SCHOOLS (EXCEPTATHLETIC FIELDS), DAYCARE FACILITIES, HOSPITALS AND OTHERCOMMERCIAL BUILDINGS THAT ARE REGULARLY OCCUPIED.

26.3 Environmental Hazards:This product is very highly toxic to wildlife. Non-target organisms exposed tophosphine gas will be killed. Do not apply directly to water or wetlands(swamps, bogs, marshes, and potholes). Do not contaminate water by clean-ing of equipment or disposal of wastes.

26.4 Endangered Species Restrictions:The use of FUMITOXIN in a manner that may kill or otherwise harm an endangeredor threatened species or adversely modify their habitat is a violation of Federallaws. Before using this pesticide on range and/or pastureland you must obtain thePESTICIDE USE BULLETIN FOR PROTECTION OF ENDANGERED SPECIESfor the county in which the product is to be used. The bulletin is available from yourCounty Extension Agent, State Fish and Game Office, or your pesticide dealer. Useof this product in a manner inconsistent with the PESTICIDE USE BULLETIN FORPROTECTION OF ENDANGERED SPECIES is a violation of Federal laws.Even if applicable, county bulletins do not prohibit the use of this product atthe intended site of application, you may not use this product for control ofprairie dogs in the states of Arizona, Colorado, Kansas, Montana, Nebraska,New Mexico, North Dakota, Oklahoma, South Dakota, Texas, Utah orWyoming unless a pre-control survey has been conducted. Contact the near-est U. S. Fish and Wildlife Service Endangered Species Specialist to deter-mine survey requirements in your area. This survey must be in compliancewith the Black-Footed Ferret Survey Guidelines, developed by the U.S. Fishand Wildlife Service, and a determination must be made in accordance withthe Guidelines that black-footed ferrets are not present in the treatment area.

35

CALIFORNIA (all endangered species) Fresno, Inyo, Kern, Kings, Madera, Merced, Monterey, San Benito, San LuisObispo, Santa Barbara, Stanislaus and TulareSee the U.S. EPA Interim Measurers Bulletin for your county. To obtain a copyof the bulletin, contact your county agricultural commissioner or visit the fol-lowing website: http://www.cdpr.ca.gov/docs/es/index.htm If there is no cur-rent bulletin available for your county, contact the U.S. Fish and WildlifeService office in Portland, OR, to determine whether there are endangeredspecies that might be adversely affected by your proposed use of FUMI-TOXIN® and the steps you should take to mitigate any such risks.FLORIDAStatewideGEORGIA Appling, Atkinson, Bacon, Baker, Ben Hill, Bleckley, Berrien, Brantley, Brooks,Bryan, Bullock, Calhoun, Camden, Chandler, Charlton, Chatham, Clinch, Coffee,Colquitt, Cook, Crisp, Decatur, Dodge, Dooly, Dougherty, Early, Echols,Effingham, Emanuel, Evans, Glynn, Grady, Irwin, Jeff Davis, Jenkins, Johnson,Lanier, Laurens, Lee, Liberty, Long, Lowndes, Macon, McCintosh, Miller, Mitchell,Montgomery, Pierce, Pulaski, Screven, Seminole, Telfair, Tattnall, Thomas, Tift,Toombs, Treutlen, Turner, Ware, Wayne, Wheeler, Wilcox and Worth.NEW MEXICOHidalgoUTAHBeaver, Garfiled, Iron, Kane, Piute, Sevier, Washington and WayneWYOMINGAlbany

26.4.1 Special Local Restrictions

1. NORTH CAROLINAFUMITOXIN tablets and pellets may only be used for control ofrats and mice in the state of North Carolina. Use against otherburrowing pests (not insect pests) is not permitted.

2. OKLAHOMAA special permit for black-tailed prairie dog control by poison-ing is required in Oklahoma. Contact the Oklahoma StateDepartment of Wildlife Conservation to obtain this permit.

3. WISCONSINA state permit is required for use of pesticides in Wisconsin tocontrol small mammals, except rats or mice. Please contact yourlocal Department of Natural Resources office for information.

4. INDIANAUse of FUMITOXIN tablets or pellets for mole control is notlegal in the state of Indiana.

36

5. MISSOURIA state permit is required for use of pesticides in Missouri tocontrol small mammals, except rats and mice. Please contactthe Missouri Department of Conservation office for information.

6. KANSASA special permit for black-tailed prairie dog control by poison-ing is required in Kansas. Contact the Kansas Fish and GameCommission to obtain this permit.

7. CALIFORNIAUse of FUMITOXIN tablets and pellets for chipmunk control isnot legal in the state of California.

27. FUMI-SLEEVE® DUST RETAINER METHOD OF FUMIGATION – Patent No.4,579,417 & 4,641,573The FUMI-SLEEVE Dust Retainer is a cotton sleeve designed to slip over the stan-dard 1-1/4” PVC probe. Contact Degesch America, Inc. or Pestcon Systems Div. formore information regarding these sleeves.The presence of residual dust from FUMITOXIN tablets or pellets in treated raw agri-cultural commodities normally presents no problems of toxicity or sanitation.Nevertheless, where it is specified that no tablets or pellets can be placed directlyinto the commodity during fumigation, conduct the fumigation in the normal mannerfollowing the directions below:

1. Determine if the structure can be made sufficiently tight by sealing allvents, windows, cracks or other openings.

2. Determine if the structure is in an area where leakage during fumigationor aeration would affect nearby workers or bystanders if concentrationswere above the permitted exposure levels.

3. Develop an appropriate Fumigation Management Plan.4. Using the Applicator’s Manual, determine the dosage and appropriate

number of probings to be used.5. The FUMI-SLEEVE dust retainer is slipped over the standard 1-1/4"

PVC probe.6. The probe with dust retainer is then inserted into the commodity.7. As the probe is withdrawn, leaving the dust retainer in the commodity,

the appropriate number of tablets or pellets is poured into the probe.8. After the probe is completely removed, leaving the dust retainer con-

taining the tablets or pellets in the commodity, tie off the top of the reten-tion sleeve in a common overhand knot. If probing is not required, theclosed sleeve may be placed on the surface of the commodity.

9. Post the structure (shiphold, barge, container on the ship, railcar orother piggyback structure) with appropriate warning signs as well as asign showing the number of FUMI-SLEEVE dust retainers used.

10. On completion of fumigation, remove all retainers from the treated com-modity and transport in a well-ventilated container to the disposal site.

37

11. Disposal:a. The entire dust retainer and residue can be buried following disposal

instructions found elsewhere in this manual.b. Or the residual dust may be emptied from the sleeve and disposed

of according to instructions found under disposal instructions inSection 28.3 of this manual.

c. It is not recommended that you reuse the sleeve.

28. DISPOSAL INSTRUCTIONS

28.1 General

Do not contaminate water, food or feed by storage or disposal.

Never place FUMITOXIN® tablets, pellets, or dust in a closed container suchas a dumpster, sealed drum, plastic bag, etc., as flammable concentrationsmay develop which could result in a flash of phosphine gas.

Partially spent or unreacted FUMITOXIN is acutely hazardous. Improper dis-posal of excess pesticide is a violation of Federal Law. If these wastes cannotbe disposed of according to the Applicator Manual instructions, contact yourState Pesticide or Environmental Control Agency, or the Hazardous Waste rep-resentative at the nearest EPA Regional Office for guidance. For specificinstructions, see Section 29 of this manual, Spill and Leak Procedures.Some local and state waste disposal regulations may vary from these generalrecommendations. Disposal procedures should be reviewed with appropriateauthorities to ensure compliance with local regulations. Contact your statePesticide or Environmental Control Agency or Hazardous Waste Specialist atthe nearest EPA Regional Office for guidance.If properly exposed, the residual dust remaining after a fumigation with FUMI-TOXIN will be a grayish-white powder. This will be a non-hazardous waste andcontain only a small amount of unreacted aluminum phosphide. However,residual dust from incompletely exposed FUMITOXIN, (so called “green dust”due to its appearance) requires special care.

Container Disposal:The aluminum flasks are non-refillable containers. Do not reuse or refill alu-minum flasks. Offer for recycling, if available. Triple rinse flasks and stopperswith water. They may then be recycled or reconditioned, or punctured and dis-posed of in a sanitary landfill, or by other procedures approved by state andlocal authorities. Rinsate may be disposed of in a sanitary landfill, by pouringit out onto the ground or by other approved procedures. It is also permissibleto remove lids and expose empty flasks to atmospheric conditions untilresidue in the flasks is reacted. In this case, puncture and dispose of in a san-itary landfill or other approved site, or by other procedures approved by stateand local authorities.

Do not transport partially spent or unreacted FUMITOXIN® residue.

38

28.2. DIRECTIONS FOR DEACTIVATION OF PARTIALLY SPENT RESIDUALDUST FROM FUMITOXIN

Any of the following conditions: low humidity, cool temperatures, shortenedexposure periods, or in cases where fumigant is added back during the fumi-gation; may result in partially spent material.Partially spent FUMITOXIN®, or unreacted product resulting from a spill orleak, must be further deactivated prior to disposal.When deactivating partially spent or unreacted product using the dry or wetmethods below, the deactivation area must be outdoors, secured and postedso as to keep unauthorized people away.

A. Wet Deactivation:Partially spent or unreacted FUMITOXIN® may be deactivated as follows usingthe “Wet Method.”Deactivating solution is prepared by adding the appropriate amount of low suds-ing detergent or surface-active agent to water in a drum or other suitable con-tainer. A 2% solution (or 4 cups in 30 gallons) of detergent is suggested. The con-tainer should be filled with deactivating solution to within a few inches of the top.Residual dust is poured slowly into the deactivating solution and stirred so as tothoroughly wet all of the particles. This should be done in the open air and not inthe fumigated structure. Dust from FUMITOXIN tablets or pellets should be mixedinto no less than about 10 gallons of water-detergent solution for each case ofmaterial used. Wear appropriate respiratory protection during wet deactivation ofpartially spent dust. Do not cover the container being used for wet deactivation.Dispose of the deactivated dust-water suspension, with or without preliminarydecanting, at a sanitary landfill or other suitable site approved by local author-ities. Where permissible, the slurry may be poured out onto the ground. If theslurry has been held for 36 hours or more, it may be poured into a storm sewer.

Caution: Wear a NIOSH/MSHA approved full-face gas mask – phosphine can-ister combination if exposed to levels between 0.3 ppm to 15 ppm or a Self-Contained Breathing Apparatus (SCBA) if exposure is unknown or above 15 ppmduring wet deactivation of partially spent material. Do not cover the containerbeing used for wet deactivation. Do not dispose of FUMITOXIN dust in a toilet.

B. Dry Deactivation:

Partiall spent or unreacted FUMITOXIN® may also be deactivated as followsusing the “Dry Method.”Extension of the fumigation period is the simplest method for further deactiva-tion of “green” or partially spent dust prior to ultimate disposal.Small amounts of partially spent dust, from 2 to 3 kg (4 to 7 lbs.) may be fur-ther deactivated by storage in a 1-gallon bucket. Larger amounts of dust(about 11 kg or 25 lbs.) may be deactivated in porous cloth bags (burlap, cot-ton, etc.). Caution: Transport these bags in open vehicles. Do not pile up thebags. Do not store partially spent or “green dust” in bags.

39

28.3 Directions for Disposal of Residual Dust From FUMITOXINConfinement of partially spent residual dust (as in a closed container) or col-lection and storage of large quantities of dust may result in a fire hazard. Smallamounts of phosphine may be given off from unreacted aluminum phosphideand confinement of the gas may result in a flash.In open areas, small amounts of residual dust up to about 5 to 8 kg (11 to 17 lbs.)may be disposed of on site by burial or by spreading over the land surface awayfrom inhabited buildings.Spent residual dust from FUMITOXIN may also be collected and disposed ofat a sanitary landfill, incinerator or other approved sites or by other proceduresapproved by Federal, State or Local authorities. “Green” or partially spent dustmust be further deactivated before disposal at a landfill.From 2 to 3 kg (4 to 7 lbs.) of spent dust from 2 to 3 flasks of FUMITOXIN maybe collected for disposal in a 1-gallon bucket. Larger amounts, up to aboutone-half case, may be collected in burlap, cotton or other types of porous clothbags for transportation in an open vehicle to the disposal site. Do not collect dustfrom more than 7 flasks of tablets or 10 flasks of pellets (about 11 kg or 25 lbs.)in a single bag. Do not pile cloth bags together. Do not use this method for“green” or partially spent dust. Caution: Do not collect dust in large drums,dumpsters, plastic bags or other containers where confinement may occur.

29. SPILL AND LEAK PROCEDURES

29.1 General Precautions and DirectionsA spill, other than incidental to application or normal handling, may producehigh levels of gas and, therefore, attending personnel must wear SCBA or itsequivalent when the concentration of phosphine gas is unknown. OtherNIOSH/MSHA approved respiratory protection may be worn if the concentra-tion is known to be less than or equal to 15 ppm. Do not use water at any timeto clean up a spill of FUMITOXIN. Water in contact with unreacted tablets orpellets will greatly accelerate the production of phosphine gas that could resultin a toxic and/or fire hazard. Wear dry gloves of cotton or other material whenhandling aluminum phosphide.Return all intact aluminum flasks to fiberboard cases or other suitable pack-aging which has been properly marked according to DOT regulations. If appli-cable, notify consignee and shipper of damaged cases.If aluminum flasks have been punctured or damaged so as to leak, the con-tainer may be temporarily repaired with aluminum tape or the FUMITOXINmay be transferred from the damaged flask to a sound metal container whichshould be sealed and properly labeled as aluminum phosphide according toDOT regulations. Transport the damaged containers to an area suitable forpesticide storage for inspection. Further instructions and recommendationsmay be obtained, if required, from DEGESCH America, Inc. or PestconSystems Div.If a spill has occurred which is only a few minutes old, collect the tablets and pellets.If they are intact, place them back into the original flasks and stopper tightly. Placethe collected tablets and pellets in a sound metal container if the original flasks aredamaged. Caution: these flasks may flash upon opening at some later time.If the age of the spill is unknown or if the tablets and pellets have been con-

40

taminated with soil, debris, water, etc., gather up the spillage and place it intosmall open buckets having a capacity no larger than about 1 gallon. Do not addmore than about one flask of spilled material, 1 to 1.5 kg (2 to 3 lbs.), to thebucket. If on-site wet deactivation is not feasible, these open containers shouldbe transported in open vehicles to a suitable area. Wet deactivation may thenbe carried out as described in 28.2.A. Alternatively, small amounts of spillagefrom 4 to 5 flasks (4 to 8 kg, 9 to 18 lbs.) may be spread out in an open areaaway from inhabited buildings to be deactivated by atmospheric moisture.

Caution: If worker protection standards will be exceeded during wet deacti-vation of unexposed or incompletely exposed FUMITOXIN, NIOSH/MSHAapproved respiratory protection must be worn. Wear a full-face gas mask –phosphine canister combination if exposed to levels between 0.3 ppm to 15ppm or a Self-Contained Breathing Apparatus (SCBA) if exposure is unknownor above 15 ppm. Never place pellets, tablets, or dust in a closed containersuch as a dumpster, sealed drum, plastic bag, etc., as flammable concentra-tions and a flash of phosphine gas are likely to develop.

Never place tablets, pellets or dust in a closed container such as a dumpster,sealed drum, plastic bag, etc., as flammable concentrations and a flash ofphosphine gas are likely to develop.

FOR ASSISTANCE CONTACT: DEGESCH AMERICA, INC.153 Triangle DriveWeyers Cave, VA 24486 USATelephone: (540)234-9281/1-800-330-2525Fax: (540)234-8225INTERNET: www.degeschamerica.comE-Mail: [email protected]

orPESTCON SYSTEMS DIV.1808 FIRESTONE PARKWAYWILSON, NC 27893-7991Tel.: (252)237-7923/1-800-548-2778Fax: (252)243-1832Internet: www.pestcon.com

orFor Human or Animal Medical Emergencies: 1-800-308-4856For All Other Chemical Emergencies: CHEMTREC: 1-800-424-9300

1257 Bedford Ave, North Kansas City, MO 64116 • www.rockwelllabs.comManufactured by:

Kills Roaches, Ants*, Crickets, Mole Crickets,Silverfish, Firebrats, and Earwigs

Kills Acrobat, Allegheny, Argentine, Big-headed, Cornfield,Crazy, Ghost, Little Black, Odorous House, Pavement,

Pyramid, Rover, Thief and White-footed Ants**Except Carpenter, Fire, Pharaoh and Harvester Ants

Multiple Food Attractants • For Indoor, Outdoor and Turf UseStarts Killing in 1 Hour

Active Ingredient: Imidacloprid.........0.5%Other Ingredients:.............................99.5%Total:...............................................100.0%

EPA Reg. No.: 73079-14EPA Est. No.: 73079-MO-1

Net Weight: 8 oz, 4 lbs, 25 lbs


PRECAUTIONARY STATEMENTSHazards to Humans and Domestic Animals: CAUTION. Causes moderate eye irritation. Avoid contact with eyes or clothing. Wash thoroughly with soap and water after handling and before eating, drinking, chewing gum, using tobacco, or using the toilet.

FIRST AIDIF IN EYES: -Hold eye open and rinse slowly and gently with water for 15-20 minutes. -Remove contact lenses, if present, after the first 5 minutes, then continue rinsing. -Call a poison control center or doctor for treatment advice.

Have the product container or label with you when calling a poison control center or doctor or going for treatment. You may also contact 800 858 7378 for emergency medical treatment information.

ENVIRONMENTAL HAZARDSThis pesticide is highly toxic to birds and aquatic invertebrates. Do not apply directly to water, or to areas where surface water is present or to intertidal areas below the mean high water mark. To protect the environment, do not allow pesticide to enter or run off into storm drains, drainage ditches, gutters or surface waters.

NOTICE: Buyer assumes all responsibility for safety and use not in accordance with directions.

Personal Protective Equipment (PPE)There are no specific requirements for applicators or other handlers, however, the following is recommended at a minimum:-Short-sleeved shirt and long pants-Shoes plus socks


Use Sites: In and around structures, including homes, apartments, commercial, industrial, municipal, institutional, research, recreational, health care, educational, daycare, hospitality and agricultural buildings and other man-made structures, garages, transport vehicles, sewers, animal research facilities, and food service, storage, handling and processing establishments. Turf sites include lawns, landscape beds, ornamental turf, parks, playing fields, right-of-ways, golf course greens and tee boxes, and home greenhouses.

How It Works: Roaches, crickets, silverfish, firebrats, and earwigs discover the bait while foraging and eat it and die. Worker ants cannot eat solid food, so they pick up the bait and take it back to the nest and feed it to the larvae. The larvae digest solid food and excrete liquid food for the rest of the colony.

Outdoor Perimeter Application: Apply bait at a rate of 1/2 – 1 oz (2 - 4 tablespoons) per 100 square feet. Use a hand shaker, duster or mechanical spreader to apply the bait. Apply in a band from 1 - 3 feet wide around the perimeter of buildings. For example, a 2 foot band around a 200 linear foot building would require 8 – 16 tablespoons (1/2 – 1 cups) of bait. Also apply around exterior light fixtures and along the edges of sidewalks, patios and driveways and under decks. Pay particular attention to potential insect harborage sites such as mulch beds, flowerbeds, fruit and vegetable gardens, compost heaps, wood piles, trees, stumps and trash areas and apply bait at the more liberal application rate in these areas. In home greenhouses, apply bait on and under benches. Do not apply bait directly in flats or pots. Pets may be attracted to this product. Do not pile the bait in exposed areas. The bait may also be sprinkled in and around rodent bait stations to control insects that harbor in these stations. When treating for ants, apply ½ to 1 oz of bait around ant mounds and sprinkle along foraging trails. For ants, pay particular attention to harborage areas and apply bait around trees and stumps, in tree cavities, in and around firewood piles, around landscaping stones and in mulch beds. Ants can take the bait back to the nest and kill the colony. Bait may also be applied in insect bait stations. Reapply bait after one week if infestation is still present. To prevent large insect populations from developing around structures in warm months, a quarterly application around the perimeter and to harborage areas, as described above, is recommended. This treatment is particularly effective to help prevent the establishment of large colonies of pest ants. If the perimeter is treated with a repellent insecticide (eg. pyrethroid), the bait may still be used around the perimeter, but it should be applied in a band outside the repellent barrier for best results. As a separate matter from the use of this product, as part of an IPM program, it is recommended that overhanging trees and other vegetation touching the structure be trimmed back, and cracks or gaps around pipes and window and door frames be sealed to minimize potential insect entry into buildings.

Turf Application: Apply bait evenly over the affected area using a hand shaker or mechanical spreader at a rate of 4 – 8 oz per 1000 square feet / 10 - 20 lbs per acre. The product should not be watered in. For mole cricket treatments, results will be best if the area is irrigated prior to bait treatment. Mole crickets typically come to the surface to feed in the evening.

Sewer Application: Apply bait at a rate of 1 oz per 100 square feet along ledges inside sewers and around manhole covers.

Indoor Application: Apply bait only in areas inaccessible to children and pets, or in tamper-resistant bait stations. Use a hand shaker or duster to apply bait. Apply up to 0.5 oz (2 tablespoons) per crack, crevice or void, or at a rate of 0.5 oz (2 tablespoons) per 100 sq ft. Trash closets, utility closets, dropped ceilings, under and behind appliances and vending machines, in wall voids and voids under and behind cabinets, sinks and tubs, in drawer wells, garbage chutes, pipe chases, elevator pits, around drains, around electrical conduits and in cracks and crevices where insects may harbor. Focus application in areas where insects or their signs are seen. Reapply bait after one week if infestation is still present. The bait may be broadcast in unfinished attics, basements and crawlspaces provided children do not have access to these areas.

Application tips for certain sites follow:1. In attics, be sure to get bait near the eaves and vent pipes where insects often first enter, as well as around any pipes or potential access points between the attic and the main structure. Attics should have proper ventilation to insure that no food odor from the bait seeps into the living area, particularly in hot weather. If in doubt, apply the product in a manner such that it can be easily removed.2. When treating cabinetry areas, if there is no gap between the lower cabinets and the kickplate, then small holes can be drilled to access the voids. Escutcheon plates around pipes can also be pulled back to allow access to voids.3. The bottom drawers in kitchen and bathroom cabinets can be removed and bait dusted into drawer wells. No bait should be left exposed when drawers are replaced.4. Electrical switch plate covers can be removed to allow access to voids, but bait shouldn’t be applied directly in electrical boxes.5. If there are cracks between baseboards, cabinets, doorframes, hinges, counters or trim, and walls, these cracks can be lightly dusted with bait. If practical, these areas can be sealed once insect problems have been eliminated, to help prevent future problems.6. Insects need moisture, so kitchen and bath areas and areas immediately surrounding them, and any other damp areas should be carefully inspected and treated if necessary. As a separate matter from the use of this product, as part of an IPM program, it is advisable to fix any leaks to minimize structural damage and odors, and to prevent potential chronic insect problems.

Food Processing and Handling Establishments, Including Federally-Inspected Food Plants: In food areas, including serving areas while the establishment is in operation, only apply bait in cracks, crevices, and other inaccessible areas, or in tamper-resistant bait stations. Never apply bait directly to a surface where food is stored, prepared or served. Follow above directions for crack and crevice placement.

Storage and DisposalDo not contaminate water, food, or feed by storage or disposal.Pesticide Storage: Store in a dry place. Do not store where children or animals may gain access.

For 25 lb containers:Container Handling: Non-refillable container. If empty: Do not reuse or refill this container. Place in trash or offer for recycling if available. If partly filled: Call your local solid waste agency or 1-800-CLEANUP which is managed as a public-private partnership.

For 8 oz and 4 lb containers: Container Handling: This storage/application container may be refilled by the end-user of the product. Do not refill with anything other than InVict Xpress Granular Bait. Do not reuse this container for anything other than InVict Xpress Granular Bait.If empty: Place in trash or offer for recycling if available. If partly filled: Call your local solid waste agency or 1-800-CLEANUP which is managed as a public-private partnership.

Warranty Limitations and DisclaimerTo the extent consistent with applicable law, seller makes no warranty expressed or implied, concerning the use of this product other than as indicated on the label. Buyer accepts this material subject to these terms, and assumes all risk of usage and handling except when used or handled in accordance with this label. To the extent consistent with applicable law, there are no expressed or implied warranties of merchantability or fitness for any particular purpose, except as specifically stated herein. To the extent consistent with applicable law, manufacturer shall not be liable for any consequential damages based on the use of the product.

Return to Index...

Return to Index....

BLA

CK

PM

S 2

99 C

PM

S 2

87 C

PM

S 1

86 C

MA

XFO

RC

E C

olor

s

2.87

5”

3.37

5”

Net

Wt.

33g

(1.1

6 O

z)79

4321

3580

2115

38B

11

0316

A

ACTI

VE IN

GR

EDIE

NT:

Fip

roni

l†...

......

......

......

....0

.05%

OTH

ER IN

GR

EDIE

NTS

:.....

......

......

......

......

......

99.9

5%†C

AS N

O. 1

2006

8-37

-3EP

A Re

g. N

o. 4

32-1

460

EPA

Est.

No. 0

7110

6-GA

-003

Note

: Do n

ot re

mov

e this

labe

l. Use

only

in ar

eas n

ot ea

sily

acce

ssibl

e to c

hildr

en an

d pe

ts.

KEE

P O

UT

OF

REA

CH

OF

CH

ILD

REN

AN

D P

ETS

CAU

TIO

N

Max

frc

e®

Roa

ch K

iller

Bai

t G

el

FC M

AG

NU

M

Keep

gel

away

from

food

s and

food

cont

act

surfa

ces.

Harm

ful if

abs

orbe

d th

roug

h sk

in.

Caus

es m

oder

ate

eye

irrita

tion.

Avoid

cont

act

with

skin,

eye

s and

clot

hing.

Was

h th

orou

ghly

with

soap

and

wat

er a

fter h

andli

ng.

CONT

AINE

R DI

SPOS

AL: If

em

pty:

Do n

ot

reus

e co

ntain

er. P

lace

in tra

sh o

r offe

r for

re

cycli

ng if

ava

ilable

. If p

artly

fille

d: Ca

ll you

r loc

al so

lid w

aste

age

ncy o

r 1-8

00-C

LEAN

UP

for d

ispos

al ins

truct

ions.

Neve

r plac

e un

used

pr

oduc

t dow

n an

y ind

oor o

r out

door

dra

in. If

yo

u ha

ve q

uesti

ons r

egar

ding

the

use

of th

is pr

oduc

t, ca

ll toll

free

1-8

00-3

31-2

867.

May

stain

texti

les, f

abric

s and

/or p

orou

s su

rface

s.Re

fer t

o lea

flet f

or co

mple

te Fi

rst A

id,

Dire

ction

s for

Use

, Pre

caut

ionar

y Sta

tem

ents

and

Stor

age

and

Disp

osal

Instru

ction

s.

A D

ivis

ion

of B

ayer

Cro

pSci

ence

LP

2 T.

W. A

lexa

nder

Driv

eR

esea

rch

Tria

ngle

Par

k, N

C 2

7709

Prod

uct o

f Chi

na

Prod

uced

for:

Return to Index...

7943213580215495B 110316A

MaxfMaxf rcerce®

Roach Killer Bait Gel

FC MAGNUM

PRECAUTIONARY STATEMENTS:HAZARDS TO HUMANS AND DOMESTIC ANIMALSCAUTIONHarmful if absorbed through skin. Causes moderate eye irritation. Avoidcontact with skin, eyes and clothing. Wash thoroughly with soap andwater after handling and before eating, drinking, chewing gum or usingtobacco.PHYSICAL AND CHEMICAL HAZARDS: Do not use this product in or onelectrical equipment where a possibility of shock hazard exists.

STORAGE AND DISPOSALDo not contaminate water, food or feed by storage or disposal.STORAGE: Store in a cool, dry area out of reach of children. DISPOSAL: If Empty: Do not reuse container. Place in trash or offerfor recycling if available. If Partly Filled: Call your local solid waste agency for disposalinstructions. Never place unused product down any indoor oroutdoor drain.If you have questions regarding the use of this product, please call1-800-331-2867.

Long lasting controlNo vapor, fumes or odorFor indoor and outdoor use Kills roaches quickly See visible resultsovernight† American, Oriental, Brown, Smoky Brown

Provides FAST CONTROL in 2 days (German roaches).Dual Action kills roaches two ways.Contains Fipronil, which kills roaches by ingestion and contact. Afterforaging roaches either eat or contact the bait, they return to theharborage and kill other roaches.Kills roaches in their harborage.Inject bait into cracks and crevices or apply as a spot where roachesharbor or enter a structure.This product effectively controls large roaches†. This product contains Fipronil, a fast-acting active ingredient that killsAmerican roaches. This product controls large roach† populations in 8days.

DIRECTIONS FOR USEIt is a violation of Federal Law to use this product in a manner

inconsistent with its labeling.Use MAXFORCE® FC MAGNUM ROACH KILLER BAIT GEL as a spot orcrack and crevice treatment for the indoor and outdoor (adjacent tohomes & structures) control of cockroaches in residential areas and thenon-food/non-feed areas of institutional, warehousing and commercialestablishments, including warehouses, restaurants, food processingplants, supermarkets, hospitals, nursing homes, motels, hotels,apartment buildings, bakeries, beverage plants, breweries, bottlingfacilities, candy plants, canneries, cereal processing and manufacturingplants, dairies and dairy product processing plants, frozen food plants,schools, laboratories, computer facilities, sewers, ”aircraft,“ buses,boats/ships, trains, homes, houses, industrial buildings, office buildings,kennels, kitchens, manufacturing facilities, spice plants, stores, wineriesand similar structures, mausoleums, meat processing and packagingplants, meat and vegetable canneries, pet shops and zoos. Non-food/non-feed areas include bedrooms, living rooms, bathrooms,closets, media rooms, garbage rooms, lavatories, entries, and vestibules,offices, locker rooms, machine rooms, boiler rooms, garages, mopclosets and storage (after canning or bottling). This product may also beused in food/feed areas of food/feed handling establishments as outlinedbelow. May stain textiles, fabrics and or porous surfaces.USE RESTRICTIONSDo not treat food preparation surfaces. Keep gel away from foods andfood contact surfaces. Do not apply bait gel to areas which have beenrecently sprayed with insecticide, and do not spray insecticide over gelas it may cause the bait to become repellent. USE ONLY IN AREAS NOTEASILY ACCESSIBLE TO CHILDREN AND PETS. In pet shops and zoosplace bait out of reach of pets and zoo animals.GENERAL DIRECTIONSApplication rate for all uses: Application rate varies according to the levelof infestation and species to be controlled. Apply gel as round spots orthin beads into cracks and crevices or as a spot treatment. Place baitclose to cockroach harborages, foraging and feeding areas such ascorners and cracks and crevices. Numerous smaller bait placementsprovide faster control than fewer larger placements. In cases of severeinfestation and areas with excessive clutter or alternative food sourcesthat cannot be eliminated, use the higher rate of application.

FOR USE IN COMMERCIAL, INDUSTRIAL AND RESIDENTIAL AREAS

ACTIVE INGREDIENT: Fipronil*: [5-Amino-1-(2, 6-dichloro-4-trifluoromethyl) phenyl)-4-(1, R, S)-(trifluoromethyl) sulfinyl)-1H-pyrazole-3-carbonitrile] .................................................................................................................0.05%OTHER INGREDIENTS:.........................................................................................................................................................99.95%

Total: ........................................................................................................................................................................................100.00%*CAS NO. 120068-37-3EPA Reg. No. 432-1460 EPA Est. No. 071106-GA-003

STOP - Read the label before use.Keep out of reach of children.

CAUTIONProduct may stain textiles and clothing.

Long lasting controlNo vapor, fumes or odor

For indoor and outdoor useKills roaches quickly

See visible results overnight

FIRST AIDIF ON SKINORCLOTHING:

• Take off contaminated clothing.• Rinse skin immediately with plenty of water for

15-20 minutes.• Call a poison control center or doctor for treatment

advice.• Hold eye open and rinse slowly and gently with

water for 15-20 minutes.• Remove contact lenses, if present, after the first 5

minutes, then continue rinsing.• Call a poison control center or doctor for treatment

advice.

IF IN EYES:

Have the product container or label with you when calling a poisoncontrol center or doctor or going for treatment. You may also contact

1-800-334-7577 for emergency medical treatment information.

Return to Index...

German cockroaches, Brown Banded Cockroaches and storedproduct pests:For use in maintenance programs where regular [monthly, quarterly]applications are made for continuous control of cockroach populations,use 0.75 grams of bait per square yard. This rate will not provide fastcontrol of existing infestations.For light to moderate infestations (or for retreatments), use up to 1.5grams of bait per square yard.To clean out severe or heavy infestations, use up to 3.0 grams of baitper square yard.Large cockroaches such as American, Smokey-Brown or Oriental: 1to 2 grams of bait per square yard."

For outdoor use (adjacent to home -or- structure): Place bait in areasadjacent to structures where large roaches may nest or breed. Apply baitto potential points of insect entry, such as eaves, sills, and expansionjoints.Apply bait in protected areas whenever possible. Environmental stressessuch as direct sunlight and water will reduce the residual effectiveness.Priority treatment areas may be identified by visual inspection of suchareas listed above or aided by trapping techniques or spot flushing. Refillable stations: MAXFORCE FC MAGNUM ROACH KILLER BAIT GELmay be placed into refillable bait stations designed for interior or exterioruse; when placing bait in stations do not exceed 1 gm (1/5 teaspoon) anddo not exceed the capacity of the stations. Close the station securely afterapplication. During follow up visits inspect placements and reapply asneeded. Directions for loading reservoirs and operation:1. With the teeth of the drive rod facing up, pull the drive rod all the way

back. If the drive rod is initially hard to move, simply un-screw (turncounter-clockwise) the black portion of the applicator that holds thegel reservoir until the drive rod moves easily.

2. Attach a pre-filled reservoir of gel with a twist-locking motion.Remove the outlet cap and attach a dispensing tip. After use, thereservoir may be resealed with the enclosed black outlet cap. Theblack outlet cap is reusable.

3. Turn the knob of the drive rod so that the teeth are facing down andmove it slightly forward so that the trigger mechanism will engage.Squeeze the trigger until the drive plunger seats against the piston inthe gel reservoir. Gently squeeze the trigger until the gel flows out.

4. If gel continues to flow after the trigger is released, simply un-screwthe portion of the bait applicator that holds the reservoir to a pointwhere gel does not continue to flow after the trigger is released.

Directions for changing reservoirs: With the arrow on the drive rodpointing up, pull the drive rod out as far as it will go. Remove the emptyreservoir and follow instructions in the Storage and Disposal box.Reservoirs that still contain gel can be sealed with the end cap and outletcap for future use. To attach a new reservoir follow the above directions.Pest population reduction will be apparent within 1 day for German

roaches and 3-4 days for American roaches.IMPORTANT: READ BEFORE USE

Read the entire Directions for Use, Conditions, Disclaimer of Warrantiesand Limitations of Liability before using this product. If terms are notacceptable, return the unopened product container at once. By using this product, user or buyer accepts the following Conditions,Disclaimer of Warranties and Limitations of Liability.CONDITIONS: The directions for use of this product are believed to beadequate and must be followed carefully. However, it is impossible toeliminate all risks associated with the use of this product. Crop injury,ineffectiveness or other unintended consequences may result because ofsuch factors as weather conditions, presence of other materials, or themanner of use or application, all of which are beyond the control of BayerCropScience LP. All such risks shall be assumed by the user or buyer.DISCLAIMER OF WARRANTIES: TO THE EXTENT CONSISTENT WITHAPPLICABLE LAW, BAYER CROPSCIENCE LP MAKES NO OTHERWARRANTIES, EXPRESS OR IMPLIED, OF MERCHANTABILITY OR OFFITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE, THAT EXTENDBEYOND THE STATEMENTS MADE ON THIS LABEL. No agent of BayerCropScience LP is authorized to make any warranties beyond thosecontained herein or to modify the warranties contained herein. TO THEEXTENT CONSISTENT WITH APPLICABLE LAW, Bayer CropScience LPdisclaims any liability whatsoever for special, incidental or consequentialdamages, resulting from the use or handling of this product.LIMITATIONS OF LIABILITY: TO THE EXTENT CONSISTENT WITHAPPLICABLE LAW, THE EXCLUSIVE REMEDY OF THE USER OR BUYER FORANY AND ALL LOSSES, INJURIES OR DAMAGES RESULTING FROM THEUSE OR HANDLING OF THIS PRODUCT, WHETHER IN CONTRACT,WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY OR OTHERWISE,SHALL NOT EXCEED THE PURCHASE PRICE PAID, OR AT BAYERCROPSCIENCE LP 'S ELECTION, THE REPLACEMENT OF PRODUCT.Bayer (reg’d), the Bayer Cross (reg’d) and MAXFORCE® are registeredtrademarks of Bayer.

A Division of Bayer CropScience LP2 T. W. Alexander DriveResearch Triangle Park, NC 27709Product of China

Produced for:

PANTRY PESTS: To control exposed, adult stages of beetles: cadelle,cigarette beetle, confused flour beetle, dermestid, drugstore beetle, flatgrain beetle, granary weevil, lesser grain borer, lesser mealworm,mealworm, merchant grain beetle, red flour beetle, rice weevil, rusty grainbeetle, saw-toothed grain beetle, spider beetle, or warehouse beetle. Afterremoving infested foodstuffs and cleaning up spilled foodstuffs and dust,applications of this product will kill adult stages of beetles remaining inarea. Apply in voids, cracks and crevices, behind and under cupboards,and other difficult to reach areas where insects may hide. Application rateis dependent on level of infestation. Applications in Food/Feed Handling Establishments: Applicationwithin food/feed areas of food/feed handling establishments islimited to crack and crevice treatment only. If gel contacts anexposed surface where food is handled, remove gel and washexposed surface with an effective cleaning compound followed by apotable water rinse prior to use. Apply with Maxforce Bait Injectordirectly into cracks and crevices. Place applicator tip 1/2 inch into cracks,crevices, holes and other small openings where roaches may be aproblem. Apply small amounts of gel. Use Restrictions in Food/Feed Handling Establishments:Do not apply bait to areas where food/feed, utensils or processingsurfaces may become contaminated. Do not apply bait to areas that areroutinely washed such as cracks and crevices in tops of tables, food/feedpreparation and prepared food holding surfaces as bait may be removedby washing. Do not apply bait to surfaces where the temperature exceeds130°F as bait may run. Examples include, but are not limited to, portionsof stoves, ovens, grills, fume hoods, heat lamps, coffee urns, steamtables, toasters, fryers, dishwashers and hot water pipes. Care should betaken to avoid depositing gel onto exposed surfaces. If gel contacts anexposed surface, remove gel and wash exposed surface. Food/feed areas include areas for receiving, storage, packing (canning,bottling, wrapping, boxing), preparing edible waste storage, and enclosedprocessing systems (mills, dairies, edible oils, syrups). Serving areas arealso considered a food/feed area when food is exposed and facility is inoperation. Apply bait in small amounts between different elements ofconstruction, between equipment and floors, openings leading into voidsand hollow spaces in floors, walls, ceilings, equipment legs and bases,around plumbing pipes, doors and windows, behind and underrefrigerators, cabinets, sinks, closets, stoves and other equipment wherecockroaches hide. During follow-up visits inspect bait placements andreapply when necessary. Application of this product in food/feed areas of food/feed handlingestablishments other than as a crack and crevice treatment is notpermitted. Gel placements should be at or near harborages or aggregation areas,such as corners or cracks and crevices. Numerous smaller placementswill provide faster control than fewer larger spots, especially for Germancockroach control.

Bait Quantity Reference Table

Approximate weight per spotdiameter

Approximate weight per beadlength1/3 gram = 1.5 inch bead0.1 gm = ¼ inch diameter spot

1.0 gm = Dime size spot 2/3 gram = 3.0 inch bead1.5 gm = Quarter size spot 1 1/3 gram = 6 inch bead

Place bait under baseboards, sinks, countertops, seats, around waterpipes, water heaters, dishwasher equipment, in crack and crevices aswell as voids where insects harbor.

Front

Tear along dotted line

ACTIVE INGREDIENT: Imidacloprid, 1-[(6-Chloro-3-pyridinyl)methyl]-N nitro-2 imidazolidinimine ........................................................... 10.0%Z-9-Tricosene ..................................................................................................................................................................................................... 0.1%OTHER INGREDIENTS: ........................................................................................................................................................................... 89.9%TOTAL: ........................................................................................................................................................................................................ 100.0%EPA Reg. No. 432-1455 EPA Est. No. 33967-NJ-1

STOP - Read the label before use.Keep out of reach of children.

CAUTIONFIRST AID

Ifswallowed:

If on skinor clothing:

If in eyes:Remove contact lenses, if present, after the first 5 minutes, then continue

rinsing eye.

In case of emergency call toll free the Bayer Environmental Science Emergency Response Telephone No. 1-800-334-7577. Have the product container or label with you when calling a poison control center or doctor or going for treatment.Note To Physician: No specific antidote is available. Treat the patient symptomatically.

DIRECTIONS FOR USEIt is a violation of Federal law to use this product in a manner inconsistent

with its labeling. IMPORTANT: Read entire label before using this product.

Product InformationThis product is a bait formulated to control house flies in rural and urban environments, in animal confinement areas (e.g., cattle, poultry, swine), in commercial establishments, and outdoors in residential areas. The product can be

Net Contents: 2 oz (56.7 g)7900069379040482C 140407AV2

MAXFORCE® FLY SPOT BAIT

prior.

6 weeks unless the bait is completely consumed.

house flies to their death® bittering agent to help prevent

ingestion by non-target animals, children and pets

WHERE TO APPLY limited to: poultry houses, turkey and chicken houses, cattle, sheep and goat

facilities, feedlots, dairy barns, swine confinement buildings, dog kennels, and horse stables.

structures, or partly enclosed or protected areas

HOW TO APPLY COVERAGE RE-APPLY QUESTIONS ??

used as a spray for treatment of surfaces, such as stable walls or waste containers, or it can be used as a paint-on application to walls and other surfaces such as pillars and compartment walls.There is no need to spray the complete surface because this bait will attract pests to the treated area. Begin applications at the start of the season before fly populations have reached their peak.Best results occur when the product is applied to many locations throughout the structure or facility. Spray the product on surfaces where house flies tend to rest. House flies prefer warm, still sites for resting, so avoid cool or windy locations.Begin applications at the start of the season before fly populations have reached their peak.

PRECAUTIONARY STATEMENTSHAZARDS TO HUMANS AND DOMESTIC ANIMALSCAUTION: Harmful if swallowed. Avoid contact with eyes, skin, or clothing. Wash thoroughly with soap and water after handling and before eating, drinking, chewing gum, or using tobacco. Wear long-sleeved shirt and long pants, socks, shoes, and chemical-resistant gloves made of any waterproof material such as, barrier laminate, butyl rubber, nitrile rubber, neoprene rubber, natural rubber, polyethylene, polyvinylchloride (PVC) or viton.ENVIRONMENTAL HAZARDSThis product is highly toxic to aquatic invertebrates. Do not apply directly to water, or to areas where surface water is present or to intertidal areas below the mean high water mark. Do not contaminate water when disposing of equipment washwaters or rinsate. This product is highly toxic to bees exposed to direct treatment or residues on blooming crops or weeds. Do not apply this product or allow it to drift to blooming crops or weeds if bees are visiting the treatment area. This chemical has properties and characteristics associated with chemicals detected in groundwater. The use of this chemical in areas where soils are permeable, particularly where the water table is shallow, may result in groundwater contamination.

PRODUCT FACTS

insecticides.

FLY SPOT BAIT

Return to Index...

Tear along dotted line

How and where to apply

FOR USE IN OTHER AREAS such as non-food/non-feed areas of commercial food handling establishments, restaurants, and dining areas, residential backyards, on and around dumpsters and trash collection areas, storage facilities, dog kennels, zoos, animal rearing facilities, schools, hospitals, nursing homes, offices, marinas, and other locations where flies tend to aggregate and are a nuisance or a health hazard.Spray applicationSpray diluted product where house flies aggregate: on walls, around windows, on surfaces of dumpsters or trash collection bins, etc. For best results, apply product on spots of 3 to 12 sq ft where house flies tend to rest.If treating spots 10 sq ft in size, you can apply up to 50 such bait spots in a building with 1,000 sq ft of floor space without exceeding the limit of 8 ounces of product for a building of this size.Paint on applicationsFor best results, paint the product in small bands up to 6 inches wide, or more, on places where house flies aggregate. Apply this product at a rate of 8 ounces for every 1,000 sq ft of floor space.Food/Feed Handling EstablishmentsApplications in food/feed handling establishments are permitted ONLY in non-food/non-feed areas. Non-food/non-feed areas include garbage rooms, lavatories, entries and vestibules, offices, locker rooms, machine rooms, boiler rooms, mop closets and storage (after packaging, canning or bottling).Food/feed handling establishments are defined as places other than private residences in which exposed food/feed is held, processed, prepared or served. Included also are areas for receiving, storing, packing (canning, bottling, wrapping, boxing), preparing, edible waste storage and enclosed processing systems (mills, dairies, edible oils, syrups) of food.Serving areas, when food is exposed and the facility is in operation, are also considered food/feed areas. However, applications of this product may be made in serving areas ONLY while the facility is not in operation, and provided exposed food has been covered, or removed from the area being treated prior to application. These “spot” applications may cover no more than 2 sq ft per treated area, may not be spaced closer than 10 ft apart, and should be a minimum of 6 feet above floor level.Contamination of food or food contact surfaces must be avoided. Do not apply this product to any food, food packaging, or any food contact surfaces.

STORAGE AND DISPOSALDo not contaminate water, food, or feed by storage or disposal.Storage:Store in a cool, dry place and in such a manner as to prevent cross contamination with other pesticides, fertilizers, food, or feed. Store in original containers and out of the reach of children, preferably in a locked storage area. Handle and open container in a manner as to prevent spillage.Pesticide Disposal: Wastes resulting from the use of this product may be disposed of on site or at an approved waste disposal facility.Container Handling: Non-refillable container. Do not reuse or refill this container. Completely empty container. Wrap used container and place in trash can.

Spills:If the container is leaking or material is spilled, carefully sweep up spilled bait and wash exposed area. In spill or leak incidents, keep unauthorized people away.You may contact the Bayer Environmental Science Emergency Response Team for decontamination procedures or any other assistance that may be necessary. The Bayer Environmental Science Emergency Response Telephone No. is 1-800-334-7577.

IMPORTANT: READ BEFORE USERead the entire Directions for Use, Conditions, Disclaimer of Warranties and Limitations of Liability before using this product. If terms are not acceptable, return the unopened product container at once.By using this product, user or buyer accepts the following Conditions, Disclaimer of Warranties and Limitations of Liability.CONDITIONS: The directions for use of this product are believed to be adequate and must be followed carefully. However, it is impossible to eliminate all risks associated with the use of this product. Crop injury, ineffectiveness or other unintended consequences may result because of such factors as weather conditions, presence of other materials, or the manner of use or application, all of which are beyond the control of Bayer CropScience LP. All such risks shall be assumed by the user or buyer.DISCLAIMER OF WARRANTIES: TO THE EXTENT CONSISTENT WITH APPLICABLE LAW, BAYER CROPSCIENCE LP MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED, OF MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE, THAT EXTEND BEYOND THE STATEMENTS MADE ON THIS LABEL. No agent of Bayer CropScience LP is authorized to make any warranties beyond those contained herein or to modify the warranties contained herein. TO THE EXTENT CONSISTENT WITH APPLICABLE LAW, BAYER CROPSCIENCE LP DISCLAIMS ANY LIABILITY WHATSOEVER FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OR HANDLING OF THIS PRODUCT.LIMITATIONS OF LIABILITY: TO THE EXTENT CONSISTENT WITH APPLICABLE LAW, THE EXCLUSIVE REMEDY OF THE USER OR BUYER FOR ANY AND ALL LOSSES, INJURIES OR DAMAGES RESULTING FROM THE USE OR HANDLING OF THIS PRODUCT, WHETHER IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY OR OTHERWISE, SHALL NOT EXCEED THE PURCHASE PRICE PAID, OR AT CROPSCIENCE LP’S ELECTION, THE REPLACEMENT OF PRODUCT.

Bayer (reg’d), the Bayer Cross (reg’d) and Maxforce® are registered trademarks of Bayer.Bitrex® and Contains Bitrex® are registered trademarks of Johnson Matthey Public Limited Company.

FOR USE IN broiler houses, turkey houses, caged layer houses, feedlots, dairy barns, swine confinement buildings, horse stables, kennels, and other animal confinement facilities where house flies tend to be a nuisance or a health hazard.Spray applicationSpray diluted product where house flies aggregate: on walls, around windows, on surfaces of pillars and other structures, etc. For best results, apply product in spots of 3 to 12 sq ft where house flies tend to rest. If treating spots 10 sq ft in size, you can apply up to 50 such bait spots in a building with 1,000 sq ft of floor space without exceeding the limit of 8 ounces of product for a building of this size.Paint on applicationFor best results, paint the product in small bands up to 6 inches wide, or more, on places where house flies aggregate. Apply this product at a rate of 8 ounces for every 1,000 sq ft of floor space.Residual Efficacy in animal facilitiesResidual efficacy in animal facilities is dependent on the sanitary conditions and fly pressure level, as well as on the quality and cleanliness of the surfaces treated.Apply as soon as fly pressure exceeds acceptable threshold levels to avoid population build up. Re-apply as needed, typically at 4 to 6 week intervals.When spraying surfaces, care must be taken only to spray places out of reach of the animals. Do not spray directly on animals, feed and drinking supplies nor on milking equipment. This also applies to empty pens due to be re-stocked within the next few weeks. Do not treat surfaces that people frequently contact. Avoid contact with sprayed surfaces until dry.

Produced for:Bayer Environmental ScienceA Division of Bayer CropScience LP2 T. W. Alexander DriveResearch Triangle Park, NC 27709Product of China

Applications of this product may leave a visible residue or discolor some surfaces. Before treating, it is advisable to test application in a small inconspicuous area.Restrictions

For Best Results

management practices.

Mixing Directions and Use RatesFor spray applications, add the contents of one 2 ounce packet of this product to 1 pint of water and agitate until completely mixed. One pint of finished spray will treat 125 sq ft of fly-resting surfaces.For paint-on applications, add 8 ounces of this product to 8 ounces of water (approximately 1 cup), and mix to desired consistency for best painting results. Apply this mixture in narrow bands up to 6 inches wide on suitable fly-resting surfaces. Do not apply this product at a rate exceeding 8 ounces for every 1,000 sq ft of floor space.Application equipmentFor spray applications, apply as a coarse fan or cone spray. Apply solution at a low pressure not to exceed 20 psi. Flush spray equipment with water to prevent clogging.For paint-on applications, use a brush or roller paint applicator to apply solution to surfaces. Clean application and mixing equipment with water after application.

FLY MANAGEMENTWHERE TO • For use only around the outside of commercial facilities like canneries, dairy ,meat and poultryAPPLY processing plants, beverage plants, food processing plants, restaurants, bakeries, supermarkets,

warehouses, dumpsters, grease pits, recycling areas, loading docks.• For use only outside of agricultural production facilities like broiler houses, feedlots, livestock

housing structures, and horse stables.• For use only around the outside of and in walkways of caged layer houses. Place bait in areas

inaccessible to animals.• In horse stables, apply bait only in fly bait stations. Place bait stations in areas inaccessible to

animals.USE RATE • 5.7 to 6.3 oz/1000 sq. ft. (scatter bait and bait station)HOW TO Apply the bait in many locations. Avoid cool or windy locations because flies prefer warmAPPLY sites for resting.

Time applications to begin at the start of the season before fly populations have reached their peak.• Scatter Application: Scatter the bait directly from the directly container onto dry

level surfaces so that the individual granules lie near each other without forming small piles.• Bait stations: Place in any fly bait station. Use 1 bait station to cover approximately 250 sq ft

and add up to 1.6 oz of bait per station. Secure bait stations at least 4 feet above the ground. Bait stations should be inaccessible to food producing animals, children and pets.

• Paint-on application: Mix 1.5oz bait with 1 fl oz warm water (3 lbs bait in1 quart water) and stirthoroughly. Let stand for about 15 minutes until a paste consistency suitable for painting hasformed. Apply the paste with a brush to surfaces where flies rest avoiding surfaces that are dusty.

RESTRICTIONS • Do not place bait in areas accessible to food producing animals, children and pets.• Do not allow bait to come into contact with food or water.• Do not apply to milking equipment.• Do not apply inside food processing plants, restaurants or other commercial facilities.

MANAGEMENT TIPS• For best results: use the bait as part of an overall integrated Pest Management program.• Use proper sanitation and manure management.• Use along with dilutable sprays like TEMPO.• Use environmental controls, such as proper light management.• Consult with cooperative Extension.STORAGE AND DISPOSALDo not contaminate water, food or feed by storage or disposal. STORAGE: Store in a cool, dry place and in such a manner as to prevent cross contamination with other pesticides, fertiliz-ers, food, or feed. Store in original container and out of the reach of children, preferably in a locked storage area. Handleand open containers in a manner as to prevent spillage.PESTICIDE DISPOSAL: Wastes resulting from the use of this product may be disposed of on site or at an approved wastedisposal facility.CONTAINER DISPOSAL: Completely empty container. Dispose of container at an approved waste disposal facility or byincineration if allowed by state and local authorities. Do not use container in connection with food, feed or drinking water.SPILLS: If the container is leaking or material is spilled, carefully sweep up spilled bait and wash exposed area. In spill orleak incidents, keep unauthorized people away. You may contact the Bayer Emergency Response Team for decontaminationprocedures or any other assistance that may be necessary. The Emergency Response Telephone No. is 800-334-7577 orcontact Chemtrec at 800-424-9300.IMPORTANT: READ BEFORE USERead the entire Directions for Use, Conditions, DIsclaimer of Warranties and Limitations of Liability before using this product. If terms are notacceptable, return the unopened product container at once.By using this product, user or buyer accepts the following conditions, warranty, disclaimer of warranties and limitations of liability.CONDITIONS: The directions for use of this product are believed to be adequate and should be followed carefully. However, because of manner of useand other factors beyond BayerEnvironmental Science’s control, it is impossible for Bayer Environmental Science to eliminate all risks associated withthe use of this product. As a result, crop injury or ineffectiveness is always possible. All such risks shall be assumed by the user or buyer. All such risksshall be assumed by the user or buyer.DISCLAIMER OF WARRANTIES: BAYER ENVIRONMENTAL SCIENCE MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED OFMERCHANTABILITY OR OF FITNESS FOR PARTICULAR PURPOSE OR OTHERWISE, THAT EXTEND BEYOND THE STATEMENTS MADE ON THISLABEL. No agent of Bayer Environmental Science is authorized to make any warranties beyond those contained herein. Bayer Environmental Sciencedisclaims any liability whatsoever for special, incidental or consequential damages, resulting from the use or handling of this product.LIMITATION OF LIABILITY: THE EXCLUSIVE REMEDY OF THE USER OR BUYER FOR ANY AND ALL LOSSES, INJURIES OR DAMAGES RESULTINGFROM THE USE OR HANDLING OF THIS PRODUCT, WHETHER IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY OR OTHERWISE,SHALL NOT EXCEED THE PURCHASE PRICE PAID, OR AT BAYER ENVIRONMENTAL SCIENCE’S ELECTION, THE REPLACEMENT OF PRODUCT.©Bayer AG, 2005

PRECAUTIONARY STATEMENTSHAZARDS TO HUMANS AND DOMESTIC ANIMALSCAUTION : Harmful if swallowed, absorbed through skin, or inhaled. Avoid contact with eyes, skin orclothing. Wash thoroughly with soap and water after handling and before eating, drinking or using tobacco.

FIRST AIDIF SWALLOWED: -Call a poison control center or doctor immediately for treatment advice.

-Have person sip a glass of water if able to swallow.-Do not induce vomiting unless told to by a poison control center or doctor.-Do not give anything to an unconscious person.

IF ON SKIN: -Take off contaminated clothing.-Rinse skin immediately with plenty of water for 15-20 minutes.-Call a poison control center or doctor for treatment advice.

IF INHALED: -Move person to fresh air.-If person is not breathing, call 911 or an ambulance, then give artificial respiration, preferably mouth-to-mouth if possible.

-Call a poison control center or doctor for further treatment advice.IF IN EYES: -Hold eye open and rinse slowly and gently with water for 15 to 20 minutes. Remove

contact lenses, if present, after the first 5 minutes, then continue rinsing eye.-Call a poison control center or doctor for treatment advice.

Have the product container or label with you when calling a poison control center or doctor or goingfor treatment. The Emergency Response Telephone No. is 800-334-7577. Note To Physician: Nospecific antidote is available. Treat patient symptomatically.

ENVIRONMENTAL HAZARDSThis product is highly toxic to aquatic invertebrates. Do not apply directly to water, or areas where surface water is present or to intertidal areas below the mean highwater mark. Do not contaminate water when disposing of equipment washwaters or rinsate. This product is highlytoxic to bees exposed to direct treatment or residues on blooming crops or weeds. Do not apply this product orallow it to drift to blooming crops or weeds if bees are visiting the treatment area. The chemical has properties andcharacteristics associated with chemicals detected in groundwater. The use of this chemical in areas where soils arepermeable, particularly where the water table is shallow, may result in groundwater contamination.

PRO FACTS• Fast acting• Ready-to-use scatter bait or paint-on application.• Contains a specialty formulated mixture of attractants• Controls flies resistant to organophosphates and carbamates

MAXFORCE • Ready-to-use bait containing 0.5% imidaclopridGRANULAR • Contains the attractant MuscalureFLY BAIT • Contains Bitrex bittering agent to help prevent ingestion by

animals, children and petsCONTROL • FliesWHERE TO • Around the outside of structures or partially enclosed or APPLY protected areas

• In and around agricultural production facilities• Around the outside of commercial facilities

MIXING • Ready-to-use scatter baitINFORMATION • Paint-on application: Mix the fly bait with waterHOW TO • Scatter applicationAPPLY • Place in any fly bait station

• Paint-on applicationCOVERAGE • XX Square feet (5.7 to 6.3 oz/1000 sq ft)RE-APPLY • Re-apply every 7 days as needed.QUESTIONS?? • For questions or comments, call toll-free 1-800-843-1702 or

visit us online at www.MAXFORCE.com

DIRECTIONS FOR USEIt is a violation of Federal law to use this product in a manner inconsistent with its labeling.IMPORTANT: Read entire label and Conditions of Sale before using this product.

GRANULAR F LY B A I TFOR PEST MANAGEMENT PROFESSIONALS, LIVESTOCK PRODUCERS, AND COMMERCIAL USE ONLY

ACTIVE INGREDIENT: Imidacloprid, 1-[(6-Chloro-3-pyridinyl)methyl]-N nitro-2-imidazolidinimine . . . . . . . . . . . . . . . . . . . . . . . . . . .0 . 5 0 %Z - 9 - Tr i c o s e n e . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0 . 1 0 %

OTHER INGREDIENTS: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 9 . 4 0 %TO TA L . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 0 . 0 0 %

STOP - Read the label before each use.KEEP OUT OF REACH OF CHILDREN

C A U T I O N

EPA Reg. No. 432-1375 EPA Est. No. 7319-NLD001N E T CONTENTS: 5 or 40 Pounds A Business Group of Bayer CropScience LP

Bayer Environmental Science2 T. W. Alexander DriveResearch Triangle Park, NC 27709www.bayerprocentral.comPRODUCT OF HOLLAND

Return to Index....

Return to Index.....

FOR SALE ONLY IN CALIFORNIA A Weather/Moisture Resistant Bait to Kill and Control Ants (Except Fire Ants), Carpenter Ants,

Cockroaches, Crickets, Mole Crickets, Earwigs, Silverfish, Snails and Slugs ACTIVE INGREDIENT: Orthoboric Acid ..................................................... 5.0% OTHER INGREDIENTS ........................................ 95.0% TOTAL .................................................................. 100.0%

EPA Reg. No. 64405-2 EPA Est. 64405-TN-1


FOR BOTH INTERIOR AND EXTERIOR USE

For use in and around the following structures: Above-ground Transformers, Aircraft, Apartment Buildings, Boats, Buses, Ornamental Gardens, Factories, Federally-Inspected (USDA) Meat and Poultry Plants, Food Handling Establishments, Food Processing Plants, Garages, Grocery Stores, Homes, Hospitals, Hotels, Industrial Plants, In-ground Utility Boxes, lnteriorscapes, Kennels, Lath Houses, Libraries, Markets, Military Bases, Mobile Homes, Motels, New Construction, Nursing Homes, Offices, Ornamental Home Greenhouses, Other Structures, Pedestal Boxes, Pet Stores, Public and Private Institutions, Recreational Vehicles, Restaurants, Schools, Sewers, Ships, Stores, Supermarkets, Theaters, Trains, Trucks, Utilities, Vending Machines, Warehouses, Yachts, Zoos.


Hazards to Humans & Domestic Animals CAUTION: Harmful if absorbed through skin. Causes moderate eye irritation. Avoid contact with skin, eyes or clothing.

PERSONAL PROTECTIVE EQUIPMENT (PPE) Applicators and handlers must wear: Long-sleeved shirt and long pants; water-proof gloves; and shoes plus socks. Follow manufacturer’s instructions for cleaning/ maintaining PPE. If no such instructions for washables are given, use detergent and hot water.

USER SAFETY RECOMMENDATIONS Users should: • Wash hands before eating, drinking, chewing gum,

using tobacco or using the toilet. • Remove clothing immediately if pesticide gets inside;

then thoroughly wash and put on clean clothing. • Immediately remove PPE after handling this product.

Wash the outside of gloves before removing. As soon as possible, thoroughly wash and change into clean clothing.

ENVIRONMENTAL HAZARDS Do not apply directly to water, to areas where surface water is present or to intertidal areas below the mean high-water mark. Do not contaminate water when disposing of equipment washwaters or rinsate.

DIRECTIONS FOR USE It is a violation of Federal law to use this product in a

manner inconsistent with its labeling. General Information

This product is a ready-to-use, weather/moisture resistant bait that controls and kills ants (except fire ants), cockroaches, crickets, earwigs, silverfish, snails and slugs specifically: Ants: Argentine, carpenter, thief, pharaoh, little black, pavement, odorous house and crazy ants. Cockroaches: Asian, American, brown, brownbanded, smokybrown, German and oriental cockroaches. Crickets: Camel, house, field and mole crickets. Snails and Slugs. European Earwigs.

First Aid

If In Eyes:

• Hold eye open and rinse slowly and gently with water for 15 - 20 minutes. Remove contact lenses, if present, after the first 5 minutes, then continue rinsing eyes.


If On Skin:

• Take off contaminated clothing. • Immediately rinse with plenty of water for

15 – 20 minutes. • Call a poison control center or doctor for

treatment advice. Have the product container or label with you when calling a poison control center or doctor or going for treatment. You may also contact 1-800-424-9300 for emergency medical treatment information.

Do not contaminate this product with other pesticides. If this product becomes -contaminated with another pesticide it will lose its effectiveness. Do not apply directly to food and avoid contamination of feed and foodstuff. In commercial food handling facilities, cover or remove any food during application. In food handling and other areas, bait may be placed in removable bait stations. Always record the number and location of bait stations. This product is designed to be used as a residual treatment in an -Integrated Pest -Management program incorporating good sanitation practices. Keep children and pets out of treatment area until application has been completed. Do not treat pets with this product. Avoid over-application around ornamental plants and fish ponds. Do not apply this product in combination with fertilizers, other pesticides or other -biologically-active materials.

Application Instructions Exterior Baiting to Control and Kill Snails and Slugs in Flower Gardens and Around Ornamentals, Ground-covers and Shrubs: At the beginning of the spring planting season (before damage occurs), broadcast 6 ounces per 100 square feet in areas likely to be infested with snails and slugs. It is best to apply the bait during early morning or evening when slugs and snails are present and eating. Reapply every four weeks for satisfactory control. To Control and Kill Snails and Slugs in Ornamental Home Greenhouses and Lath Houses: Evenly distribute granules on and under benches at the rate of 6 ounces per 100 Square Feet. Do Not Place In Flats Or Pots. To Control and Kill Snails and Slugs in Interiorscapes or Ornamental Gardens: Evenly apply bait to soil at a rate of 6 ounces per 100 square feet no more than once every 4 to 6 weeks. Exterior Baiting to Control and Kill Ants (Except Fire Ants), Including Carpenter Ants, Around Apartment Buildings, Food Processing Plants, Garages, Homes, Hospitals, Hotels, Kennels, Motels, Pet Stores, Public & Private Institutions, Recreational Vehicles, Restaurants, Schools, Supermarkets, Warehouses and Other Struc-tures: Treat exterior perimeter areas of structure in a band 2 to 4 feet wide at a rate of 6 ounces per 100 square feet. Also apply product in a 2- to 4-foot band around all trees, stumps, firewood piles and other locations where carpenter ants may nest. If the nest is located in a hollow tree or stump, apply 1/2 to 1 ounce of product directly into the cavity. Apply along ant trails and in areas where ant activity has been noted. To Control and Kill Ants (Except Fire Ants), Cockroaches, Crickets, Earwigs and Silverfish Within and Around the Exterior of Structures Such as Apartment Buildings, Food Processing Plants (Non-Food Areas), Garages, Homes, Hospitals, Hotels, Kennels, Motels, Pet Stores, Public & Private Institutions, Recreational Vehicles, Restaurants (Non-Food Areas), Schools, Sewers, Stores, Supermarkets and Warehouses: Apply at a rate of 4 pounds per 1000 square feet (6 ounces or 1-1/4 cups per 100 square feet) of surface area. Spread evenly in crawl spaces, attics, drop

ceilings and cellars with dirt or gravel floors. Concentrate application in areas where insect activity is most prevalent. In attics, be sure to apply in eaves and access drains. In warehouses, garages and basements, concentrate application along walls and baseboards. This product may also be applied in inaccessible areas such as cracks and crevices where insects may hide. Any bait visible after application must be brushed into cracks and crevices or removed. Apply in pits of elevator, dumbwaiter and trash chute shafts. Apply under and behind pallets and boxes in storerooms. Bait may also be placed in removable bait stations in areas accessible to insects but inaccessible to children and pets. Always record the location and number of bait stations. Regularly inspect bait stations and replace bait as needed. In sewers, apply along ledges and around manhole entrances. Treat exterior perimeter building walls in a band approximately 2 feet wide and scatter bait in flower beds, leaf litter, wood piles, trash cans and refuse areas. Reapply as necessary. For Treating New Construction: Apply in wall voids and other areas where insects may hide. For Perimeter Treatments: Spread bait at a rate of 6 ounces or 1-1/4 cups per 100 square feet in a band at least 2 feet wide around foundations, patios, driveways, sidewalks, entrances to homes and buildings, or other areas where insects are -present. Apply around landscape lighting, floodlights, street lamps or other exterior fixtures and scatter bait in flower beds, leaf litter, wood piles, trash cans and refuse areas. Reapply as necessary. For Treating Ant Mounds: Apply 1/2 to 1 ounce of this product around all ant mounds. Supplement by broadcast application in immediate area and along ant trails and in areas where ant activity has been noted. To Control and Kill Ants (Except Fire Ants), Cockroaches, Crickets, Earwigs and Silverfish in: Aircraft, Apartment Buildings, Boats, Buses, Factories, Food Handling Establishments, Food Processing Plants, Garages, Grocery Stores, Homes, Hospitals, Hotels, Industrial Plants, Kennels, Libraries, Markets, Military Bases, Mobile Homes, Motels, New Construction, Nursing Homes, Offices, Pet Stores, Private & Public Institutions, Recrea-tional Vehicles, Restaurants, Schools, Sewers, Ships, Supermarkets, Theaters, Trains, Trucks, Utilities, Warehouses, Yachts and Zoos: Food area application limited to only crack and crevice treat-ment. Apply only in areas inaccessible to children and pets. Avoid contamination of feed and foodstuffs. Apply by scattering/dusting under and behind refrigerator, cooler, stove, sink, dishwasher, washing machine and dryer tubs; counters; into openings around drains, water pipes and electrical conduits; and in cracks and crevices along baseboards and corners of cabinets, counter tops, cupboards and closets. Remove all lower drawers in kitchen and bathroom cabinets, bedroom dressers and chests of drawers, then scatter/dust in drawer wells. Bait may also be applied into and around areas of insect

infestation of above-ground transformers, in-ground utility boxes, pedestal boxes and vending machines. Any bait visible after application must be brushed into cracks and crevices or removed. Reapply as necessary. Bait may also be placed in removable bait stations in areas accessible to insects but inaccessible to children and pets. Always record the location and number of bait stations. Regularly inspect bait stations and replace bait as needed. Crack and Crevice Applications in Aircraft, Apartment Buildings, Boats, Buses, Factories, Food Handling Establishments, Food Processing Plants, Garages, Grocery Stores, Homes, Hospitals, Hotels, Industrial Plants, Kennels, Libraries, Markets, Military Bases, Mobile Homes, Motels, New Construction, Nursing Homes, Offices, Pet Stores, Private & Public Insti-tutions, Recreational Vehicles, Restaurants, Schools, Sewers, Ships, Supermarkets, Theaters, Trains, Trucks, Utilities, Warehouses, Yachts and Zoos: Crack and crevice applications may be made using most types of dust applicators. A bellows type duster works best. Insert stem into gaps, cracks and crevices and apply 2 to 6 puffs per lineal foot, depending upon the severity of the infestation. Any bait visible after application must be brushed into cracks and crevices or removed. Drill small holes to gain access into wall voids and under cabinets. Application Sites and Directions:

1. Apply under and behind appliances in kitchens, bathrooms and utility rooms -(remove kick plates if possible).

2. Kitchen and bathroom cabinets and vanities often have a space between the floor and the bottom drawer or cabinet. If a gap exists along the top of the kickplate, dust this product into the void area. If no gaps are present, drill a small hole every two feet along the kickplate, drilling at least one hole under each cabinet, and apply this product through the holes.

3. Apply in voids around plumbing pipes behind water heaters and under sinks in kitchens, bathrooms, showers and utility rooms. Pull back escutcheon plates around pipes to allow access to the void.

4. Remove electrical wall socket and switch covers and dust product around boxes and into voids. Do not apply product directly into electrical switch and outlet boxes.

5. Cracks or spaces between the wall and doorframes, cabinets, counter tops, molding or baseboards provide excellent hiding places for roaches and ants. Dust a small amount of this product into these areas wherever possible.

6. Apply under and behind vending machines. If access can be gained to the interior of the machine, apply around the interior base, being careful not to contaminate any foodstuffs.

To Control and Kill Cockroaches, Crickets, Ants, Earwigs and Silverfish in Federally-Inspected (Usda) Meat and Poultry Plants: For application only in inedible product areas and non-processing areas as a crack and crevice treatment. Apply to cracks and crevices in areas such as around baseboards and in closets; beneath

cabinets and appliances, in and around waste containers and into openings around drains, water pipes and electrical conduits. Any bait visible after application must be brushed into cracks and crevices or removed. Avoid contamination of feed and foodstuffs. Bait stations may be used. Always record the number and location of bait stations. Regularly inspect bait stations and replace bait as needed. This product is best used as a supplemental residual treatment preceded by approved spray and good sanitation practices.

STORAGE AND DISPOSAL Do not contaminate water, food or feed

by storage or disposal. Pesticide Storage: Store in a dry place. Do not store where children or animals may gain access. Pesticide Disposal: Wastes resulting from the use of this product may be disposed of on site or at an approved waste disposal facility. Container Disposal: Non-refillable container; do not reuse or refill this container. Completely empty container into application equipment, then offer for recycling, if available; otherwise dispose of empty container in a sanitary landfill or by incineration.

WARRANTY DISCLAIMER To the extent not prohibited by applicable law, Manufacturer warrants that this product conforms to the chemical description on the label and is reasonably fit for the purposes stated on the label when used in strict accordance with the directions, subject to the inherent risks set forth below. To the extent not prohibited by applicable law, MANUFACTURER MAKES NO OTHER EXPRESS OR IMPLIED WARRANTY OF MERCHANT-ABILITY, FITNESS FOR A PARTICULAR PURPOSE OR ANY OTHER EXPRESS OR IMPLIED WARRANTY.

Inherent Risks of Use The directions for use are believed to be adequate and must be carefully followed. It is impossible to eliminate all risks associated with use of this product. Lack of performance or other unintended consequences may result because of such factors as use of the product contrary to label instructions, abnormal conditions, the presence of other materials, climatic conditions or the manner of application, all of which are beyond the control of the Manufacturer. To the extent not prohibited by applicable law, the buyer/user assumes all such risks.

Limitation of Remedies To the extent not prohibited by applicable law the exclusive remedy for losses or damages resulting from this product (including claims based on contract, negligence, strict liability or other legal theories) shall be limited to, at Manufacturer’s election, one of the following: 1. Refund of purchase price paid by buyer or user for

product bought, or 2. Replacement of amount of product used. To the extent not prohibited by applicable law: a) Manufacturer shall not be liable for losses or damages resulting from handling or use of this product unless

Manufacturer is promptly notified of such loss or damage in writing; and b) TO THE EXTENT NOT PROHIBITED BY APPLICABLE LAW, IN NO CASE SHALL MANUFAC-TURER BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES OR LOSSES, INCLUDING WITHOUT LIMIT, HEALTH RELATED DAMAGES OR INJURIES. The terms of this Warranty Disclaimer and Limitation of Remedies cannot be varied by any written or verbal

statements or agreements. No employee or sales agent of Manufacturer or the seller is authorized to vary or exceed the terms of this Warranty Disclaimer or Limitation of Remedies in any manner. It is not intended that this product be used to practice any patent not owned by Nisus Corporation, whether mentioned or not, without procurement of a license (if necessary) from the owner following investigation by the user.

100 Nisus Drive • Rockford, TN 37853 • 800-264-0870

Niban and Nisus Corporation are registered trademarks of Nisus Corporation. ©2015 Nisus Corporation # NBCA-SL-0215-SAL020515

SAFETY DATA SHEET

Health Emergencies: INFOTRAC® (800) 535-5053

1. PRODUCT AND COMPANY INFORMATION Product Identity: Niban® Granular Bait Recommended use of the chemical and restrictions on use: A weather/moisture resistant bait to kill and control ants (except fire ants), carpenter ants, cockroaches, crickets, mole crickets, earwigs, silverfish, snails, and slugs. Read and understand the entire label before using. Use only according to label directions. It is a violation of Federal law to use this product in a manner inconsistent to label directions. Manufacturer: Nisus Corporation 100 Nisus Drive Rockford, TN 37853 Telephone: Phone: (800) 264-0870 Fax: (865) 577-5825 Emergency Phone: 800-535-5053 (INFOTRAC) SDS Date of Preparation: 1/12/16 2. HAZARDS IDENTIFICATION GHS Classification:

Physical Health Environment

Not Hazardous

Acute Toxicity Oral Category 4 Specific Target Organ Toxicity – Repeat Exposure Category 2

Aquatic Acute Toxicity Category 3

GHS Label Elements: TE None Required Statements of Hazard Precautionary Statements None Required None Required

3. COMPOSITION/INFORMATION ON INGREDIENTS

Component CAS No. Amount

Boric Acid 10043-35-3 5%

Non-Hazardous Ingredient Proprietary 95%

The exact formulation is being withheld as a trade secret.

4. FIRST AID MEASURES Eye: Flush victim's eyes with large quantities of water, while holding the eyelids apart. Get medical attention if irritation develops or persists. Skin: Wash skin thoroughly with soap and water. Get medical attention if irritation develops. Remove and launder clothing before re-use. Ingestion: Do not induce vomiting unless directed to do so by a medical professional. Get medical attention for large ingestions or if symptoms develop or if you feel unwell. Inhalation: Remove victim to fresh air. If breathing is difficult or irritation persists, get medical attention. Most important Symptoms: May cause eye and skin irritation. Inhalation of mists may cause mild mucous membrane and respiratory irritation. Harmful if swallowed. Repeated ingestion may cause kidney damage. Indication of immediate medical attention/special treatment: Immediate medical attention is required for large ingestions.

5. FIRE FIGHTING MEASURES Suitable (and Unsuitable) Extinguishing Media: Use media appropriate for surrounding fire. Specific hazards arising from the chemical: Fine particles may present an explosion hazard if suspended in air. Burning may produce carbon monoxide and carbon dioxide.

Special Protective Equipment and Precautions for Fire-Fighting Instructions: Firefighters should wear positive pressure self-contained breathing apparatus and full protective clothing. Contain runoff.

6. ACCIDENTAL RELEASE MEASURES Personal Precautions, Protective Equipment, and Emergency Procedures: Wear appropriate protective clothing as described in Section 8. Do not apply directly to water or contaminate water. Methods and Materials for Containment and Cleaning Up: Collect and place in appropriate containers for disposal. Avoid generating dust. Clean spill area thoroughly. Prevent spill from entering sewers and watercourses. Report releases as required by local, state and federal authorities.

7. HANDLING AND STORAGE Precautions for Safe Handling: Avoid contact with the eyes, skin and clothing. Avoid breathing dusts. Wear protective clothing and equipment as described in Section 8. Wash thoroughly with soap and water after handling. Remove contaminated clothing immediately and wash before reuse. Remove PPE immediately after handling. Wash thoroughly after using and change into clean clothing. Do not apply this product in a way that will contact workers or other persons, either directly or through drift. Only protected handlers may be in the area during application. Keep containers closed when not in use. Refer product label for additional information on use and handling. Nonrefillable container. Do not reuse containers. Product residues in empty containers can be hazardous. Follow all SDS precautions when handling empty containers. Conditions for Safe Storage, Including Any Incompatibilities: Store in a dry area away from incompatible materials. Do not store where children or animals may gain access.

8. EXPOSURE CONTROLS/PERSONAL PROTECTION Exposure Guidelines:

Boric Acid 2 mg/m3 TWA ACGIH TLV (inhalable) 6 mg/m3 STEL ACGIH TLV (inhalable)

Engineering Controls: Use with adequate ventilation to maintain exposure levels below the occupational exposure limits. Refer product label for additional information. Respiratory Protection: In operations where exposure levels are exceeded, a NIOSH approved respirator with dust/mist cartridges appropriate for the form and concentration of the contaminants should be used. Selection and use of respiratory equipment must be in accordance with OSHA 1910.134 and good industrial hygiene practice. Refer to the product label for additional information. Skin Protection: Use gloves for normal application of this product. Eye Protection: Wear safety glasses to prevent eye contact. Other: Wear long-sleeve shirts, long pants, socks and shoes when using this product. Suitable washing facilities should be available in the work area.

9. PHYSICAL AND CHEMICAL PROPERTIES Appearance And Odor: Brown, granular particles with no odor. Physical State: Granular particles Odor Threshold: Not established Vapor Density: Not determined Initial Boiling Point/Range: Not determined Solubility In Water: Not soluble Vapor Pressure: Negligible Relative Density: 0.62 of water Evaporation Rate: N/A Melting/Freezing Point: N/A pH: N/A Percent Volatile: Minimal Octanol/Water Coefficient: N/A Solubility: Not soluble Decomposition Temperature: N/A Viscosity: N/A Flammability (solid, gas): Fine dust may form explosive mixtures in air Flashpoint: >451°F (233°C) TOC Autoignition Temperature: None Flammable Limits: LEL: Not determined UEL: N/A

10. STABILITY AND REACTIVITY Reactivity: Not normally reactive Chemical Stability: Stable under normal storage and handling conditions. Possibility of Hazardous Reactions: None known. Conditions to Avoid: Avoid generating fine dust. Incompatible Materials: None known Hazardous Decomposition Products: When heated to decomposition emits carbon monoxide and carbon dioxide.

11. TOXICOLOGICAL INFORMATION HEALTH HAZARDS: Ingestion: May be harmful if large quantities are ingested. Inhalation: Inhalation of dust may cause irritation of the nose, throat and upper respiratory tract. Eye: May cause slight irritation. Skin: Not expected to cause irritation. Chronic: Borates have been shown to have some chronic toxicity in animals fed high doses, but this has not been found in humans. Sensitization: This material is not expected to cause sensitization. Carcinogenicity: None of the components is listed as a carcinogen or suspected carcinogen by IARC, NTP or OSHA. Germ Cell Mutagenicity: No data available Reproductive Toxicity: Borates have been found to have some reproductive toxicity in animals, but this has not been found in humans. Numerical Measures of Toxicity: Product Toxicity Data: Oral rat LD50: >5000 mg/kg; Dermal rabbit LC50: >5050 mg/kg

12. ECOLOGICAL INFORMATION This product breaks down naturally in the environment to provide organic matter and boron micro nutrients. Boron occurs naturally in sea water at an average concentration of 5 mg B/l and fresh water at 1 mg B/l or less. In dilute aqueous solutions the predominant boron species present is undissociated boric acid. Ecotoxicity: EC10 Green Algae: 24 mg B/l; LC50 Daphnia magna: 530 mg B/l/96 hr; LC50 Dab: 74 mg B/l/48hr; LC50 Rainbow Trout: 88 mg B/l/24hr; LC50 Goldfish: 71 mg B/l/72hr Persistence and Degradability: Boron is naturally occurring and ubiquitous in the environment. Niban decomposes in the environment to natural borate. Bioaccumulative Potential: Not determined. Mobility in Soil: Boric acid is soluble in water and is leachable through normal soil. Other Adverse Effects: Some plants are sensitive to boron. This product is designed to be used for certain types of insects. Use product only as directed on the label. See product label for full instructions and restrictions on use.

13. DISPOSAL CONSIDERATION Dispose in accordance with local, state and federal environmental regulations. Do not apply directly to water, to areas where surface water is present or to intertidal areas below the mean high-water mark. Do not contaminate water when disposing of equipment washwaters or rinsate. Wastes resulting from the use of this product may be disposed of on site or at an approved waste disposal facility. Non-refillable container: do not reuse or refill this container. Completely empty container into application equipment, then offer for recycling, if available; otherwise dispose of empty container in a sanitary landfill or by incineration. For guidance contact your state water board or regional office of the EPA.

14. TRANSPORTATION INFORMATION DOT Hazardous Materials Description: Not Regulated Sea Transport IMDG, not classified as dangerous Air Trasnport IATA/ICAO, not classified as dangerous

15. REGULATORY INFORMATION This chemical is a pesticide product registered by the United States Environmental Protection Agency and is subject to certain labeling requirements under federal pesticide law. These requirements differ from the classification criteria and hazard information required for safety data sheets (SDS), and for workplace labels of non-pesticide chemicals. The hazard information required on the pesticide label is reproduced below. The pesticide label also includes other important information, including directions for use. FIFRA Labeling:

Niban Granular Bait EPA Reg. No. 64405-2

Keep Out of Reach of Children CAUTION

PRECAUTIONARY STATEMENTS Hazards to Humans & Domestic Animals

Caution: Harmful if absorbed through skin. Causes moderate eye irritation. Avoid contact with skin, eyes or clothing. CERCLA: This product is not subject to reporting under CERCLA. Some states have more stringent reporting requirements. Report all spills in accordance with local, state, and federal regulations. SARA Hazard Category (311/312): Not hazardous SARA 313: This product contains the following chemicals subject to Annual Release Reporting Requirements Under SARA Title III, Section 313 (40 CFR 372): None EPA TSCA Inventory: This product is regulated under FIFRA, thus exempt.

16. OTHER INFORMATION NFPA Rating: Health = 0 Flammability = 0 Instability = 0 HMIS Rating: Health = 1 Flammability = 0 Physical Hazard = 0 SDS Revision History: 01/07/14: New SDS 01/12/16: Revised

WARRANTY DISCLAIMER The information, data and recommendations contained herein are believed to be accurate but may not be all inclusive and should only be used as a guide. The information is furnished upon the condition that the person receiving it shall make his own determination of the suitability of the product for his particular use and on condition that they assume the risk of the use thereof. With respect to this publication and the product related thereto, unless otherwise expressly provided by Manufacturer in writing, MANUFACTURER MAKES NO EXPRESS OR IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR ANY OTHER EXPRESS OR IMPLIED WARRANTY.

Remedy/Liability Limits The exclusive remedy for losses or damages resulting from this publication or the related product (including claims based on contract, negligence, strict liability or other legal theories) shall be limited to, at Manufacturer’s sole election, one of the following:

1. Refund of purchase price paid by buyer or user for product bought, or

2. Replacement of amount of product used. Manufacturer shall not be liable for losses or damages resulting from use of this publication or handling or use of this product, IN NO CASE SHALL MANUFACTURER BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES OR LOSSES, INCLUDING WITHOUT LIMIT, HEALTH RELATED DAMAGES OR INJURIES. The terms of this Warranty Disclaimer and Remedy/Liability Limits cannot be varied by any written or verbal statements or agreements. No employee or sales agent of Manufacturer or the seller is authorized to vary or exceed the terms of this Warranty Disclaimer or Limitation of Remedies in any manner.

100 Nisus Drive • Rockford, TN 37853 USA • (800) 264-0870

Niban and Nisus Corporation are registered trademarks of Nisus Corporation. ©2016• #NB-SDS-011216a

Specimen Label

• Fast-acting microencapsulated formula

• Combines fast kill and residual control

• Kills Ants, Spiders, Scorpions, Fleas, and otherlisted insects



ACTIVE INGREDIENTS:Esfenvalerate ................................................................................6.40%Prallethrin ....................................................................................1.60%Piperonyl butoxide ........................................................................8.00%OTHER INGREDIENTS* ...............................................................84.00%

100.00%*Contains petroleum distillates

1Kills German Cockroaches for up to 12 months (1 year) on indoor, unsealed concrete and/or cement surfaces only.

INSECTS CONTROLLED:AntsAphidsAsian Lady BeetlesBed BugsBeetlesBoxelder BugsBrown Marmorated Stink BugsCarpet BeetlesCockroachesCricketsDog TicksEarwigsFire AntsFirebratsFleasMealy BugsMidgesMillipedesMitesPillbugsPsocidsScalesSilverfishSpidersSpringtailsSwarming TermitesTicksWaterbug STORED PRODUCT PESTS INCLUDING:Angoumois Grain MothsAnts

CadellesCigarette BeetlesConfused Flour BeetlesDark MealwormsDried Fruit BeetlesDrugstore BeetlesFlat Grain BeetlesFruit FliesGrain MitesGrain MothsGranary WeevilsIndian Meal MothsLesser Grain BorersMaize WeevilsMeal Moth LarvaeMediterranean Flour MothsMerchant Grain BeetlesRed Flour BeetlesRice WeevilsRusty Grain BeetlesSaw-toothed Grain BeetlesSkippersSpider BeetlesSpider MitesSquare-necked Grain BeetlesTobacco MothsYellow Mealworm FLYING INSECTS INCLUDING:Blow FliesChiggersClothes MothsCrane FliesDeer Flies

Face FliesFruit FliesFungus GnatsGnatsHorn FliesHousefliesMosquitoesSmall Flying MothsWhiteflies BITING AND STINGING PESTS:Bed BugsBeesBiting FliesChiggersDeer FliesDeer TicksDog TicksFire AntsFleasGnatsHornetsLiceMosquitoesScorpionsSpidersTicksWaspsYellow JacketsWOOD-DESTROYING PESTS INCLUDING:Carpenter AntsCarpenter BeesDeathwatch Beetles

Furniture BeetlesOld House BorersPowder Post BeetlesRound-headed House BorersSwarming TermitesPLANT PESTS INCLUDING:Alfalfa CaterpillarsAmerican Plum BorersAnnual Bluegrass WeevilsAphidsApple MaggotsArmywormsArtichoke Plum MothBagwormsBalsam Woolly AdelgidsBeet ArmywormsBillbugsBlueberry SpanwormsBrown Marmorated StinkbugCherry Fruit FliesCherry FruitwormsChinch BugsCodling MothsCowpea CurculiosCranberry FruitwormsCranberry WeevilsCucumber BeetlesCutwormsDiamondback MothsElm Leaf BeetlesEuropean Pine SawfliesFall Webworms

Filbert WormsFlea BeetlesGrasshoppersGreen CloverwormsGreen FruitwormsGypsy Moth CaterpillarsHickory ShuckwormsImported CabbagewormsJapanese BeetlesLace BugsLeaf Feeding CaterpillarsLeaf MinersLeaf RollersLeaf TiersLeafhoppersLesser ApplewormsLesser Peach Tree BorersLoopersLygus BugsMexican Bean BeetlesMitesMole CricketsNaval OrangewormsNorthern Pine WeevilsOriental Fruit MothsPainted Lady CaterpillarsPea WeevilsPeach Tree BorersPeach Twig BorersPear PsyllidPear SlugsPecan Leaf PhylloxeraPecan Nut Casebearers

Pecan SpittlebugsPecan Stem PhylloxeraPecan WeevilsPepper WeevilsPeriodical CicadasPicklewormsPillbugsPine ChafersPine Coreid BugsPlant BugsPlum CurculiosRed Pine SawfliesRed-headed Pine SawfliesRed-striped FirewormsRindwormsSalt Marsh CaterpillarsSap BeetlesScalesSod WebwormsSowbugsSpidersSpittlebugsStink BugsTarnished Plant BugsTent CaterpillarsThripsTobacco HornwormsTufted Apple Bud MothsVelvet Bean CaterpillarsWalnut Husk FliesWestern Bean CutwormsWhiteflies

DIRECTIONS FOR USEIt is a violation of Federal law to use this product in a manner inconsistent with its labeling. Remove pets and birds, cover fish aquariums before spraying.

For control of insects, indoors and outdoors, in food and non-food areas such as, but not limited to: homes, schools, warehouses, office buildings, apartment buildings, theatres, hotels, industrial buildings, motels, kennels, livestock housing, food processing plants, food service establishments, restaurants, supermarkets and grocery stores, transportation equipment, truck trailers, railroad cars, and food manufacturing and warehousing establishments. Also for use on backyards, lawns, trees, ornamental landscaping, recreational areas, parks and athletic fields.

Return to Index...

GENERAL INFORMATION:Do not apply this product in patient rooms or in any rooms while occupied by the elderly or infirm. Do not apply to classrooms while in use. Do not apply in institutions (including libraries, schools, sports facilities, etc.) in the immediate area where occupants are present. Do not apply as a space spray in residential sites. Onslaught FastCap Spider & Scorpion Insecticide is a microencapsulated suspension concentrate containing the following pounds of active ingredient per gallon: Esfenvalerate (0.54 lbs.), Prallethrin (0.135 lbs.), Piperonyl butoxide (0.675 lbs.).Onslaught FastCap Spider & Scorpion Insecticide combines fast kill (action) and long residual activity against pests listed on this label when applied as surface or spot treatments, injected into wall voids, or as a crack and crevice spray in and around residential and commercial structures, as well as on turf and landscaping. Onslaught FastCap Spider & Scorpion Insecticide may be sprayed on any surface that will not be stained by water. DO NOT use this product as a fogger or apply it as a space spray. Injector application equipment that delivers low volume treatments may be used to make crack and crevice injections or spot and general surface treatments. DO NOT apply in electrical conduits, junction and switch boxes, motor housings, or other electrical equipment due to shock hazard from water-based spray.Use only in areas described. Remove pets and cover fish aquariums and pets’ food and water dishes before spraying. Keep all people (especially children) and pets out of areas being treated and restrict access to these areas until all surfaces are dry. DO NOT leave product where children or pets can come into contact with it. DO NOT allow spray to contact food or food-containing surfaces, feed, or water supplies. Thoroughly wash dishes and food handling utensils with soap and water if they become contaminated with this product. Food utensils such as teaspoons and measuring cups must not be used for food purposes after use with pesticides.APPLICATION IN FOOD PROCESSING/HANDLING ESTABLISHMENTS:Application is permitted within food and non-food areas of food service and handling establishments (places other than private residences) including, but not limited to: restaurants, meat processing plants, grocery stores, bakeries, food manufacturing and processing establishments, and food warehousing establishments. Do not treat establishments where livestock feed is present.Food areas include areas for receiving, storing, packing, canning, bottling, wrapping, boxing, preparing, edible waste storage, and enclosed processing systems, mills, and dairies. Serving areas are places where prepared foods are served, such as dining rooms, but excluding areas where foods may be prepared or held. Non-food areas include garbage rooms, lavatories, floor drains (to sewers), entries and vestibules, offices, locker rooms, machine rooms, garages, mop closets, and storage after canning or bottling.General Surface Applications: Do not apply Onslaught FastCap Spider & Scorpion Insecticide as a general surface application in food areas of the facility when the facility is in operation or food is exposed. Do not apply directly to food. Cover or remove all food and food processing equipment prior to application. After spraying in meat packing plants, bakeries, and other food processing plants, wash with an effective cleaning compound, and then rinse all equipment, benches, shelving, etc. where exposed food will be handled with potable water. Repeat applications as needed, but do not exceed more than one (1) application every fourteen (14) days.Spot or crack & crevice applications: Spot or crack and crevice applications may be made while facility is in operation, provided exposed food is covered or removed from the area being treated. Do not apply directly to food or food-handling surfaces. Repeat applications as needed, but do not exceed more than one (1) application every fourteen (14) days.In the home, cover exposed food and do not allow spray to contact food surfaces. If spray does contact these surfaces, clean surfaces with soap and water.MIXING INSTRUCTIONS: Onslaught FastCap Spider & Scorpion Insecticide should be mixed with water and applied with hand pressurized or power operated sprayers. Agitate container of Onslaught FastCap Spider & Scorpion Insecticide before diluting by inverting it several times. Clean spray equipment before and after use. For dilution, add approximately half the required water to spray tank and then add the appropriate amount of Onslaught FastCap Spider & Scorpion Insecticide. Agitate, and slowly add the remaining water. Agitate spray thoroughly before using and also occasionally during use to ensure dispersion. If spray filter screens are used, they should be 50 mesh or larger. Use 0.5 fluid ounces (15 cc.) of Onslaught FastCap Spider & Scorpion Insecticide in 1 gallon of water for light infestations or as a maintenance control rate. Use 1.0 fluid ounce (30 cc.) per gallon of water for heavy infestations or as an initial clean out rate. Apply 2-second bursts of spray per square foot of area being treated. Avoid excessive application. Dampen surfaces but not to the point of saturation or run-off. Only dilute Onslaught FastCap Spider & Scorpion Insecticide with water.Onslaught FastCap may be sprayed on any surface that will not be stained by water. If you are concerned about staining or are not sure if a surface is water safe, test the surface by spraying a small amount in an inconspicuous area before making a broad application. The following chart indicates the percent of active ingredients that is in the sprayer tank after mixing Onslaught FastCap Spider & Scorpion Insecticide at either rate.

Dilution Rate In Water 0.5 fl. oz. per Gallon 1.0 fl. oz. per Gallon

Final % concentration of Active Ingredients

Final % concentration of Active Ingredients

Esfenvalerate 0.025% 0.050%

Prallethrin 0.006% 0.012%

Piperonyl butoxide 0.031% 0.063%

Tank Mixing:Onslaught FastCap Spider & Scorpion Insecticide may be tank mixed with an insect growth regulator such as NyGuard® IGR Concentrate or pyrethrum-containing products or any other currently registered pesticides unless expressly prohibited by the product label. The resulting tank mix may be applied in areas where these products are allowed to be sprayed. Do not tank mix Onslaught FastCap Spider & Scorpion Insecticide with products containing dichlorvos (DDVP).

INDOOR USE:Application Rates for Indoor Structural Pests:

Pests Dilution Rate In Water

Application Rate of Mixed

SolutionApplication Method(s)

Spiders and Other Listed

Crawling Insects1 Gallon / 1,000 sq. ft.

(40 ml/m2)

Apply as a coarse, wet spray • Broadcast Surface Spray • Crack & Crevice Treatment • Spot Treatment • Injected into Wall Voids

Light Infestation 0.5 fl. oz. / Gallon (3.97 ml/L)

Heavy Infestation 1.0 fl. oz. / Gallon (7.93 ml/L)

Flying Insects 0.5 fl. oz. / Gallon (3.97 ml/L)

1 Gallon / 1,000 sq. ft. (40 ml/m2)

Scorpions and Other Listed

Stinging Insects

1.0 fl. oz. / Gallon (7.93 ml/L)

1 Gallon / 1,000 sq. ft. (40 ml/m2)

Ticks 0.5 fl. oz. / Gallon (3.97 ml/L)

1 Gallon / 1,000 sq. ft. (40 ml/m2)

Fleas, Lice & Bed Bugs


1 Gallon / 1,000 sq. ft. (40 ml/m2)

Apply as noted above, with a fine particle spray.

Spiders, scorpions and other listed crawling insect pests indoors:Apply as a course, wet spray to surfaces where these pests are normally found. Treat floors, baseboards, around doors and windows, in attics, crawl spaces, eaves, corners, closets, walls, utility pipes, storage areas, and all cracks and crevices. Treat underneath sinks, dishwashers, refrigerators, stoves, the underside of shelves, drawers, cabinets, areas behind pipes, and in all places where these insects shelter. Contact as many insects as possible with direct spray. Repeat applications as needed, but do not exceed more than one (1) application every seven (7) days.For ant control indoors:Apply to ant trails, around garbage receptacles, and near food sources. Also apply around doors and windows and wherever these pests may find entrance to the structure. Remove sources of food through basic hygiene practices whenever possible.Flying insect pests indoors:Treat insect resting areas such as walls and ceilings, screens, around windows, doors, and light fixtures, and other surfaces that attract flying insects. Initiate treatments at the beginning of fly season, and repeat treatments during periods of heavy infestation.Stinging insect pests indoors:Apply spray to nests late in the evening when stinging insects are at rest. Thoroughly spray nest, nest entrance, and surrounding areas where insects land or walk. Treat around doors and windows, in attics, crawl spaces, and possible harborage sites or points of entry.For control of Brown Dog Ticks:Thoroughly apply as a spot treatment to infested areas such as pet beds and resting areas, nearby cracks and crevices, along and behind baseboards, window and door frames, and localized areas of floor and floor coverings where these pests may be present. DO NOT SPRAY PETS WITH THIS PRODUCT. Treat dogs and cats with a product registered for use on animals.For control of Fleas: Thoroughly apply as a fine particle broadcast spray to infested rugs, carpets, and pet resting areas. Prior to treatment, aquariums and fish bowls should be covered, and pet animals should be removed from the area being treated. Do not permit humans or pets to contact treated surfaces until spray has dried. Old pet bedding should be removed and replaced with clean, fresh bedding after treatment. DO NOT SPRAY PETS WITH THIS PRODUCT. Treat dogs and cats with a product registered for use on animals.To control Bed Bugs:Thoroughly clean and vacuum mattresses, box springs, floors, and surfaces. Treat mattresses and box springs with an approved pesticide, such as a pyrethrin aerosol. Apply Onslaught FastCap Spider & Scorpion Insecticide as a spot treatment to potential harborage sites and migration paths, and cracks and crevices, around baseboards, floorboards, headboards, wall voids and walls.For control of stored product pests:Spray thoroughly around and into floor drains, non-food conveyors, benches, pipes, pallets, moist areas, storage racks, pieces of equipment, and other areas where stored product pests may be found. Tank-mix or sequential use of an insect growth regulator, such as NyGuard® IGR Concentrate, is recommended to break the insect reproduction cycle. Do not apply this spray to surfaces or utensils that may come in contact with food, since excessive residues in food may result.To treat voids in equipment and structures: To kill insects harboring in wall voids and other inaccessible spaces in equipment and structures, use injection equipment designed for deep void applications. Follow the injection equipment manufacturer’s recommendations for proper set up and air pressures.

Place the applicator tip at or into the void space to be treated. For inaccessible voids, it may be necessary to drill an access hole(s). Inject product into the void space in short bursts, allowing air pressure to push insecticide deep into the space. Avoid applying to the point of runoff or drip. Ventilate area thoroughly before re-entry. Do not reapply more than every fourteen (14) days.To kill the accessible stages of listed granary insects: Use this concentrate to treat grain storage facilities, and other listed areas, for stored product pest control. For control of exposed adult and immature stages of stored product pests, apply to cracks, crevices, and other surfaces where the pests have been seen or have harborage. Treat areas where products are stored before filling with the product. Apply at the rates listed above, using one gallon of spray mix per 1000 square feet of surface area to be treated. Cleaning all areas prior to use will increase levels of control. Any foodstuffs infested with pests should be removed and destroyed. Do not apply when food-processing facility is in operation or foods are exposed. Do not apply this spray to surfaces or utensils that may come into contact with food. Repeat application as needed, but do not exceed more than one application every fourteen (14) days.USE IN AND AROUND LIVESTOCK HOUSING:For use in and around unoccupied areas of livestock facilities, such as, but not limited to: barns, cow and calf pens & hutches, dairy barns & milk rooms, hog barns, horse barns, sheep barns, poultry houses, and rabbit hutches. Do not contaminate milk, food, or drinking water. Remove animals from area being treated. Cover feeders and waterers. Do not apply or allow insecticide to drift onto animals. Do not allow animals to enter treated areas until spray solution has dried.

Pests Dilution Rate In Water Application Method(s)

Crawling Insects Including Litter Beetles

1 fl. oz. / Gallon (7.93 ml/L) or

1 fl. oz. in sufficient water to cover 1,000 sq. ft.

(0.32 ml/m2)

Apply as a coarse, wet spray • General Surface Spray • Crack & Crevice

Treatment • Spot Treatment • Injected into Wall

VoidsFlying Insects


or 0.5 fl. oz. in sufficient

water to cover 1,000 sq. ft. (0.16 ml/m2)

Crawling insect pests in livestock and poultry premises:Apply as a general surface, spot treatment, and/or crack and crevice treatment. Apply to floors and vertical and overhead surfaces where crawling insects are or may be present. Treat stanchions, pipes, windows, doors, posts, cage framing, gates, under (but not in) feeders, and other areas where insects hide or congregate. To reduce immigration of insects, make a perimeter treatment around the outside of building foundations. Apply in a uniform band 1 – 3 feet (0.3 – 0.9 m) up the exterior foundation wall and 3 – 6 feet (0.3 – 1.8 m) out from the foundation.Litter Beetle control in livestock and poultry premises:To control Litter Beetles (Darkling, Hide, and Carrion Beetles), apply Onslaught FastCap Spider & Scorpion Insecticide to walls and floors at cleanout and before reintroduction of animals. Treat areas where beetles frequently occur, such as walls, supports, cages, cage framing, stalls, and around feeders. To reduce immigration of insects, make a perimeter treatment around the outside of building foundations. Apply in a uniform band 1 – 3 feet (0.3 – 0.9 m) up the exterior foundation wall and 3 – 6 feet (0.3 – 1.8 m) out from the foundation.Flying insect pests in livestock and poultry premises:For residual control of flying insects, treat insect resting areas such walls, ceilings, screens, around windows, doors, light fixtures, and other surfaces that attract flying insects. Initiate treatments at the beginning of fly season and repeat treatments during periods of heavy infestation. Tank-mix or sequential use of an insect growth regulator, such as NyGuard® IGR Concentrate, is recommended to break the insect reproduction cycle.

OUTDOOR USE:Do not spray in or near fishponds or other bodies of water.Do not water the treated area to the point of run-off.Do not make applications during the rain.Do not apply directly to sewers or drains, or any area like a gutter where drainage to sewers, storm drains, water bodies, or aquatic habitat can occur, except as directed by this label.Not for use on plants being grown for sale or other commercial use. Not for use in nurseries, sod farms or golf courses.All outdoor applications, if permitted elsewhere on this label must be limited to spot or crack-and-crevice treatments only, except for the following permitted uses, if allowed elsewhere on this label:1. Applications to soil or vegetation, as listed on this label.2. Applications to lawns, turf, and other vegetation, as listed on this label.3. Applications to the side of a building, up to a maximum height of 3 feet above grade;4. Application to underside of eaves, soffits, doors, or windows permanently protected from

rainfall by a covering, overhang, awning, or other structure;

5. Applications around potential pest entry points into buildings, when limited to a surface band not to exceed one inch in width;

6. Applications made through the use of a coarse, low pressure spray to only those portions of surfaces that are directly above bare soil, lawn, turf, mulch or other vegetation, as listed on this label; and not over an impervious surface, drainage or other condition that could result in runoff into storm drains, drainage ditches, gutters, or surface waters in order to control occasional invaders or aggregating pests as listed on this label.

Outdoor applications for spiders, scorpions and other listed pests:

Dilution Rate In Water Application Method(s)

Treating Exterior Walls, Foundations and

Structures

0.5 to 1 fl. oz. / Gallon (3.97 ml to 7.93 ml/L)

or 0.5 to 1 fl. oz. in sufficient water to cover 1,000 sq. ft.

(0.16 ml to 0.32 ml/m2) Apply as a coarse, wet spray • Crack & Crevice

Treatment• Spot Treatment

Treating Nests and Harborage Areas of

Stinging Insects


1 fl. oz. in sufficient water to cover 1,000 sq. ft. (0.32 ml/m2)

To Control Swarming Termites and Wood

Destroying Pests


1 fl. oz. in sufficient water to cover 1,000 sq. ft. (0.32 ml/m2)

Treating Ornamental Trees and Landscapes

0.1 to 1.0 fl. oz. / Gallon (0.793 ml to 7.93 ml/L)

or 0.1 to 1.0 fl. oz. in sufficient water to cover 1,000 sq. ft. (0.032 ml to 0.32 ml/m2)

Apply as a course, wet spray • Broadcast Spray

Treatment• Foliar Spray

TreatmentMosquito Breeding Sites

0.5 fl. oz. / Gallon (3.97 ml/L) or

0.5 fl. oz. in sufficient water to cover 1,000 sq. ft. (0.16 ml/m2)

Treating Lawns and Turf

0.1 to 1 fl. oz. / Gallon (0.79ml to 7.93 ml/L)

or 0.1 to 1 fl. oz. in sufficient water to cover 1,000 sq. ft. (0.032 ml to 0.32 ml/m2)

or 4.3 to 43 fl. oz. per acre

(127 ml to 1,271 ml/acre)

Apply as a course, wet spray • Broadcast Spray

Treatment

Treating exterior walls, foundations and structures: To control infestations of listed pests, treat exterior surfaces of buildings, walls, window frames, around garbage cans, eaves, cracks and crevices, porches, decks, gazebos, patios, carports, siding, garages, fence lines, and other areas where pests are active or may be hiding. To help prevent insect infestation of buildings: Treat a 2 – 6 foot (0.6 – 1.8 m) band of soil or other substrate adjacent to buildings. Treat building foundation to a height of 2 – 3 feet (0.6- 0.9 m). Treat exterior walls, siding, eaves, cracks and crevices, and other areas where listed pests are active, and may find entrance into building. Apply with sufficient water to adequately cover the area being treated, but do not allow dripping or run-off to occur. Alternate mixing directions are to use 2 to 4 fluid ounces of concentrate per 50 gallons of water.Stinging insect control outdoors:For stinging insects, apply spray solution to nests and harborage areas late in the evening when stinging insects are commonly at rest. Thoroughly spray nest, nest entrance, harborage sites, and surrounding areas where insects land or walk. For nests inside walls, inject sufficient spray to treat nest. Do not use in areas where an electrical shock hazard exists. For applications made when pests are active, applicator should wear protective equipment as required. Repeat application when there are signs of renewed insect activity.For Yellow Jacket control, Onslaught FastCap Spider & Scorpion Insecticide can be mixed with baits in traps. Follow trap instructions for preparation of bait. For control of Fire Ants, combine broadcast application with mound drenches to control foraging workers and newly mated fly-in queens. Apply Onslaught FastCap Spider & Scorpion Insecticide as a broadcast application at a rate of 8 fl. oz. of concentrate per 1,000 square feet (2.54 ml/m2). Treat mounds with a registered Fire Ant mound treatment.

Fleas and Ticks outdoors:To control fleas and pet ticks, apply to kennels, runs, and other areas that pets have been present. For best outdoor control of ticks, apply spray to vegetation, brush, branches, and other areas near habitation where ticks may harbor or frequent. Treat the entire area and retreat as necessary to maintain control. Do not apply to pasture or cropland and do not allow animals and people to access to treated areas until the application has dried. DO NOT SPRAY PETS WITH THIS PRODUCT. Treat dogs and cats with a product registered for use on animals.

Insect control in ornamental trees and landscapes:For residential and commercial trees, shrubs, ground covers, and bedding and foliage plants that will not be harvested for food, apply Onslaught FastCap Spider & Scorpion Insecticide in appropriate volumes of water to obtain thorough coverage. Apply as a full-coverage foliar spray, applying to the point of drip but not runoff. Treat active soil pests with an application to surrounding soil. Repeat treatments as necessary to achieve control, using higher application rates as pest pressure and foliage area increases. Repeat applications as necessary, but no more than once every seven (7) days. Certain plants may be sensitive to the final spray solution. A small-scale test is recommended to verify safety to ornamental plants. Spray and observe for one (1) week prior to application of an entire planting.

Insect control on lawns, turf grass, and turf:For best results, lawn or turf grass should be mowed 1 – 2 days before spraying. Treat with spraying equipment or a hand sprayer. Use application volumes of up to 10 gallons per 1,000 square feet (400 ml/m2)to get uniform coverage when treating dense grass foliage. For low volume applications using less than 2 gallons of spray solution per 1,000 square feet (80ml/m2), immediate irrigation with at least 0.25 inches (0.635 cm) of water is recommended to improve effectiveness on sub-surface pests.

When hand spraying, spray using a slow, even sweeping motion, making sure to cover the entire lawn or turf grass area where pests are observed. Spray under ornamentals and trees. Repeat treatments may be necessary at 7 – 14-day intervals.

Rate range:Use lower rate range for pests that are commonly exposed and will be contacted by spray solution at the time of application. For pests that will not be contacted by spray solution at the time of application, use the upper rate range. Use 1 fl. oz per 1,000 sq. ft. (7.93 ml/L) when treating Mole Crickets and Chinch Bugs.

To kill Swarming Termites: OUTDOORS ONLYApply spray mix as a coarse, wetting spray when swarming termites are seen emerging from woodpiles, wooden fence posts, wooden structures, or from the ground. Swarming usually occurs in the spring or at other times when a termite colony becomes overcrowded and new reproductive termites with wings emerge and fly away to mate and establish new colonies. This treatment will control the sprayed termites and will not protect the structure from which the swarm is coming. Use only as a contact spray to kill emerging reproductive (winged) and worker termites emerging from infested wood. This treatment is not a substitute for a comprehensive termite control program.

To kill wood destroying pests: OUTDOORS ONLY Apply spray mix as a coarse, wetting spray to exposed pests and to the damaged areas of wood, spraying into galleries or tunnels in the exposed wood. Also, spray around doors, window and door frames, and other areas where these pests may hide or enter the house. Spray into cracks and crevices and, if necessary, drill small holes and spray into inaccessible wooden structural voids where these pests are suspected.

Mosquito breeding sites:Mosquito populations may be reduced by application of Onslaught FastCap Spider & Scorpion Insecticide to sites where mosquitoes rest, harbor, and breed. Apply spray solution into tall grass, shrubbery, and around backyards and lawns where these pests may hover or rest. Apply while air is still.

Not for wide area mosquito abatement using aerial or truck mounted cold aerosol ULV sprayers and thermal fogging devices.

FIRST AIDIF SWALLOWED: • Call a poison control center or doctor immediately for treatment advice.

• Do not give any liquid to the person.

• Do not induce vomiting unless told to do so by a poison control center or a doctor.

• Do not give anything by mouth to an unconscious person.

IF IN EYES:• Hold eye open and rinse slowly and gently with water for 15-20 minutes.

• Remove contact lenses, if present, after the first 5 minutes, then continue rinsing eyes.


IF ON SKIN OR CLOTHING:• Take off contaminated clothing.

• Rinse skin immediately with plenty of water for 15-20 minutes.


NOTE TO PHYSICIAN: Contains petroleum distillate. Vomiting may cause an aspiration pneumonia hazard.

Have the product container or label with you when calling a poison control center or doctor, or going for treatment. For information regarding medical emergencies or pesticide incidents, call 1-888-740-8712.

PRECAUTIONARY STATEMENTS HAZARDS TO HUMANS AND DOMESTIC ANIMALS

CAUTIONHarmful if swallowed. Causes moderate eye irritation. Avoid contact with skin, eyes or clothing. Wear protective eyewear (goggles, face shield or safety glasses with side shields). Wash hands thoroughly with soap and water after handling and before eating, drinking, chewing gum, using tobacco or using the toilet.

ENVIRONMENTAL HAZARDSThis product is toxic to fish and other aquatic invertebrates. To protect the environment, do not allow pesticide to enter or run off into storm drains, drainage ditches, gutters or surface waters. Applying this product in calm weather when rain is not predicted for the next 24 hours will help to ensure that wind or rain does not blow or wash pesticide off the treatment area. Rinsing application equipment over the treated area will help avoid run off to water bodies or drainage system.

Do not discharge effluent containing this product into lakes, streams, ponds, estuaries, oceans, or other waters unless in accordance with the requirement of a National Pollutant Discharge Elimination System (NPDES) permit and the permitting authority has been notified in writing prior to discharge. Do not discharge effluent containing this product into sewer systems without previously notifying sewage treatment plant authority. For guidance, contact your State Water Board or Regional Office of the EPA.

PHYSICAL OR CHEMICAL HAZARDSDo not use this product in or on electrical equipment due to the possibility of shock hazard.

STORAGE AND DISPOSAL:Do not contaminate water, food, or feed by storage or disposal.

PESTICIDE STORAGE: Store in a cool, dry area under lock and key. Post as a pesticide storage area. Always store pesticides in the original container. Store away from food, pet food, feed, seed, fertilizers, and veterinary supplies. Place liquid formulations on lower shelves and dry formulations above.

PESTICIDE DISPOSAL:To avoid wastes, use all material in this container by application according to label directions. If wastes cannot be avoided, offer remaining product to a waste disposal facility or pesticide disposal program (often such programs are run by state or local government or by industry).

CONTAINER HANDLINGNonrefillable container. Do not reuse or refill this container.

Triple rinse as follows: Empty the remaining contents into the application equipment or a mix tank and drain for 10 seconds after the flow begins to drip. Fill the container ¼ full with water and recap. Shake for 10 seconds. Pour rinsate into the application equipment or a mix tank or store rinsate for later use or disposal. Drain for 10 seconds after the flow begins to drip. Repeat this procedure two more times. Then offer for recycling if available, or puncture and dispose of in a sanitary landfill or by incineration. Do not burn unless allowed by state and local ordinances.


EVERCIDE®, Exponent®, MGK®, NyGuard® are registered trademarks of MGK Company. Manufactured by MGK®. ©2013 MGK. All rights reserved.


2.5M-0612

For sale to, use and storage only by individuals/firms licensed or registered by thestate to apply termiticide and/or general pest control products.

Active Ingredient:Chlorfenapyr: 4-bromo-2-(4-chlorophenyl)-1-(ethoxymethyl)5-(trifluoromethyl)-1H-pyrrole-3-carbonitrile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21.45%Other Ingredients: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78.55%Total: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100.00%1 gallon contains 2.0 pounds of active ingredient.

EPA Reg. No. 241-392 EPA Est. No.

KEEP OUT OF REACH OF CHILDREN.

CAUTION/PRECAUCIÓN

See inside booklet for complete First Aid, Precautionary Statements, Directions For Use and Conditions of Sale and Warranty.

For Product Use Information, Call 1-877-837-6436

In case of an emergency endangering life or property involving this product,call day or night 1-800-832-HELP (4357).

Net Contents:

Si usted no entiende la etiqueta, busque a alguien para que se la explique a usted en detalle.(If you do not understand this label, find someone to explain it to you in detail.)

BASF Corporation26 Davis DriveResearch Triangle Park, NC 27709

Return to Index....


HAZARDS TO HUMANS AND DOMESTIC ANIMALS

CAUTIONHarmful if swallowed, inhaled or absorbed throughthe skin. Causes moderate eye irritation. DO NOTget in eyes, on skin, or on clothing. Avoid breathingvapors or spray mist. Wash thoroughly with soapand water after handling and before eating, drinking,chewing gum or using tobacco. Remove contami-nated clothing and wash clothing before reuse.

Personal Protective Equipment (PPE)Some materials that are chemical-resistant to this productare listed below. If you want more options, follow theinstructions for Category C on an EPA chemical resist-ance category selection chart.

All pesticide handlers (mixers, loaders and applica-tors) must wear:• Long-sleeved shirt and long pants• Chemical-resistant gloves such as barrier laminate, butyl

rubber or nitrile rubber, neoprene, or polyvinyl chloride(PVC), or viton (≥14 mils).

• Shoes plus socks

Follow manufacturer’s instructions for cleaning/maintainingPPE. If no such instructions for washables, use detergentand hot water. Keep and wash PPE separately from otherlaundry.

In addition, all termiticide handlers must wear a dust/mistfiltering respirator (MSHA/NIOSH Approved Number PrefixTC-21C) or a NIOSH approved respirator with any N, R, Por HE filter, when working in a non-ventilated space,including but not limited to crawl-spaces and basements;all termiticide handlers must wear protective eyewear

when working in a non-ventilated space when applyingtermiticide by rodding or sub-slab injection.

Environmental HazardsThis pesticide is toxic to aquatic organisms, birds andwildlife. DO NOT apply directly to water or to areas wheresurface water is present or intertidal areas below the meanhigh water mark. DO NOT contaminate water by cleaningof equipment or when disposing of equipment washwa-ters or rinsate.

Physical or Chemical HazardsDO NOT apply this product around electrical equipmentdue to the possibility of shock hazard.

Storage and DisposalDO NOT contaminate water, food, or feed by storage ordisposal.

Pesticide Storage: Store in original container in securedry storage area. DO NOT store below 32 degrees F.DO NOT store in direct sunlight or heat.

To Contain a Spill: In case of spills, avoid contact andisolate area. To confine spills, dike surrounding area orabsorb with sand, cat litter, commercial clay, gel or similarabsorbents.

User Safety Recommendations

Users should:• Wash hands before eating, drinking, chewing gum,

using tobacco or using the toilet.• Remove contaminated clothing. Then wash thoroughly

and put on clean clothing.• Remove PPE immediately after handling this product.

Wash the outside of gloves before removing. As soonas possible, wash thoroughly and change into cleanclothing.

2

FIRST AID

If swallowed

• Call a poison control center or doctor immediately for treatment advice.• Have person sip a glass of water if able to swallow.• DO NOT induce vomiting unless told to do so by the poison control center or doctor.• DO NOT give anything by mouth to an unconscious person.

If on skin or clothing• Take off contaminated clothing.• Rinse skin immediately with plenty of water for 15-20 minutes.• Call a poison control center or doctor for treatment advice.

If inhaled

• Move person to fresh air.• If person is not breathing, call 911 or an ambulance, then give artificial respiration,

preferably mouth-to-mouth, if possible.• Call a poison control center or doctor for treatment advice.

If in eyes• Hold eye open and rinse slowly and gently with water for 15-20 minutes.• Remove contact lenses, if present, after the first 5 minutes, then continue rinsing eye.• Call a poison control center or doctor for treatment advice.

HOT LINE NUMBER

Have the product container or label with you when calling a poison control center or doctor, or going for treatment. In case of anemergency endangering life or property involving this product, call day or night 1-800-832-HELP (4357).

Pesticide Disposal: Wastes resulting from the use of thisproduct may be disposed of on site or at an approvedwaste disposal facility.

Container Disposal:Nonrefillable Container. DO NOT reuse or refill thiscontainer. Triple rinse or pressure rinse container (orequivalent) promptly after emptying; then offer for recy-cling, if available, or reconditioning, if appropriate, or punc-ture and dispose of in a sanitary landfill, or by incineration,or by other procedures approved by state and localauthorities.

Triple rinse containers small enough to shake(capacity ≤ 5 gallons) as follows: Empty the remain-ing contents into application equipment or a mix tankand drain for 10 seconds after the flow begins to drip.Fill the container 1/4 full with water and recap. Shake for10 seconds. Pour rinsate into application equipment ora mix tank, or store rinsate for later use or disposal.Drain for 10 seconds after the flow begins to drip.Repeat this procedure two more times.

Pressure rinse as follows: Empty the remaining con-tents into application equipment or mix tank and contin-ue to drain for 10 seconds after the flow begins to drip.Hold container upside down over application equipmentor mix tank, or collect rinsate for later use or disposal.Insert pressure rinsing nozzle in the side of the containerand rinse at about 40 PSI for at least 30 seconds. Drainfor 10 seconds after the flow begins to drip.

DIRECTIONS FOR USE

It is a violation of federal law to use this product in a man-ner inconsistent with its labeling. This label must be in thepossession of the user at the time of pesticide application.

For sale to, use and storage only by individuals/firmslicensed or registered by the state to apply termiticideand/or general pest control products. States may havemore restrictive requirements regarding qualifications ofpersons using this product. Consult the structural pestcontrol regulatory agency of your state prior to use of thisproduct.

FAILURE TO FOLLOW THE DIRECTIONSFOR USE AND PRECAUTIONS ON THISLABEL MAY RESULT IN POOR PESTCONTROL.

GENERAL PRECAUTIONS FOR TERMITICIDE APPLICATIONS

When treating adjacent to an existing structure, theapplicator must check the area to be treated, and imme-diately adjacent areas of the structure for visible andaccessible cracks and holes to prevent any leaks or sig-nificant exposures to persons occupying the structure.People present or residing in the structure during appli-cation must be advised to remove their pets and them-selves from the structure if the applicator or residentssee any signs of leakage. After application, the applicatoris required to check for leaks. All leaks resulting in thedeposition of termiticide in locations other than thoseprescribed on this label must be cleaned up prior toleaving the application site. DO NOT allow people orpets to contact contaminated areas or to reoccupy con-taminated areas of the structure until the clean up iscompleted.

All holes drilled in concrete slabs in commonly occupiedareas into which termiticide has been applied must beplugged. Plugs must be of a non-cellulose material orcovered by an impervious, non-cellulose material.DO NOT make treatment beneath slabs or similar floor-ings until the locations of heat or air conditioning duct-work, vents, water and sewer lines, and electricallines/conduits are known and identified. Use extremecaution to avoid puncturing and contaminating theseutilities.

When treating crawl spaces or plenum-type structures,turn off any air circulation system that moves air from thearea to be treated to an untreated interior space of thestructure until application has been completed and allPHANTOM® termiticide-insecticide has beenabsorbed by the soil.

DO NOT contaminate wells or cisterns. Consult theappropriate section of this label as well as state/localspecifications for recommended distances of wells fromtreated area, or if such regulations do not exist, refer toFederal Housing Administration (H.U.D.) Specificationsfor guidance.

Use anti-backflow or air gap equipment with filling hoses.DO NOT contaminate public or private water supplies.Consult state, federal, or local authorities for informationregarding the approved treatment practices for areas inclose proximity to potable water supplies.

DO NOT treat within a distance of one foot out from thedrip line of edible plants.

USE DIRECTIONS FOR TERMITE CONTROL

3

GENERAL INFORMATION

In order to maximize the termite potency of PHANTOM®

termiticide-insecticide it should be applied in a mannerto provide a continuous treated zone to prevent termitesfrom attacking the wood to be protected.

PHANTOM is effective on Reticulitermes spp. (R. flavipes,R. virginicus, R. hageni, R. tibialis, R. Hesperus),Coptotermes spp. (C. formosanus), and Heterotermesspp. (H. aureus).

The objective of soil treatments with PHANTOM is toestablish a treated zone (horizontal and/or vertical asneeded) between the wood and other cellulose material inthe structure and the termite population(s) in the soil forthe purpose of protecting the structure from termite infes-tation and/or for controlling existing termite populations.Treatment standards for subterranean termite control mayvary due to state/local regulations, treatment procedures,soil types, construction practices and other factors. Followall federal, state, and local regulations and treatment stan-dards for protection of a structure from subterranean ter-mites. Observe industry good management practices.

Where aerial infestations or above-ground nests aredetected within the structure, supplemental treatments tocontrol termites in the structure (see Above GroundTermite Infestations section of this label), and/or struc-tural repairs to deprive the termites of a moisture sourcemay be needed.

For advice concerning current control practices, consultresources in structural pest control, state cooperativeextension or regulatory agencies.

MIXING DIRECTIONS

Dilution Table:

For Mixing Small Volumes of Finished DilutionFor termite control operations requiring smaller volumes,use 1.5 fl oz of PHANTOM per gallon of water to achievea 0.25% concentration; use 0.75 fl oz of PHANTOM pergallon of water to achieve a 0.125% concentration. Mixthe termiticide use dilution in the following manner:

1. Fill hand-pressurized or power-operated applicationequipment with 1/2 to 3/4 of the required amount ofwater. Filling hose must be equipped with an anti-back-flow device or water flow must include an air gap toprotect against back siphoning.

2. Measure the required amount of PHANTOM.3. Add PHANTOM to the sprayer and fill with the remain-

der of the water.4. Close sprayer and agitate to insure proper suspension.5. Re-agitate sprayer before use if spraying is interrupted.

For Mixing Large Volumes of Finished DilutionFor dilution quantities greater than one gallon, the amountof PHANTOM to add may be determined by multiplyingthe quantity of PHANTOM specified for a particular dilu-tion rate for a one-gallon dilution by the total dilution size.For example to make a 50-gallon dilution of a 0.125%dilution, multiply 50 x 0.75 fl oz = 37.5 fl oz. Then mix37.5 fl oz of PHANTOM to enough water to make a total50 gallon dilution. For termite control operations requiring100 gallons of finished dilution, prepare a 0.25% dilutionby mixing 1.2 gallons of PHANTOM with 98.8 gallons ofwater; or prepare a 0.125% dilution by mixing 75 fluidounces (fl oz) of PHANTOM with 99.4 gallons of water.Mix the termiticide use dilution in the following manner:1. Fill the tank with water until it is 1/4 to 1/3 full. Filling

hose must be equipped with an anti-backflow device orwater flow must include an air gap to protect againstback siphoning.

2. Start pump to begin by-pass agitation and place end oftreating tool in tank to allow circulation through hose.

3. Add the appropriate amount of PHANTOM (seeDilution Table above).

4. Add remaining amount of water to the tank.5. Let pump run and allow recirculation through the hose

for 2 or 3 minutes.

Application VolumeTo provide maximum control of and protection against ter-mite infestations, apply the specified volume ofPHANTOM dilution and active ingredient as set forth inthe directions for use. If soil will not accept the labeledapplication volume, the volume may be reduced providedthere is a corresponding increase in concentration so thatthe amount of active ingredient applied to the soil remainsthe same. Note: Large reductions of application volumereduce the ability to obtain a continuous treated zone.Variance is allowed when volume and concentration areconsistent with label directed rates and a continuous treat-ed zone can still be achieved. At reduced application vol-ume; it may be necessary for the applicator to space rodand/or drill holes closer than 12 inches apart to create acontinuous treated zone. DO NOT treat soil that is watersaturated or frozen or in any conditions where run-off ormovement from the treatment area (site) is likely to occur.DO NOT make outdoor treatments while precipitation isoccurring that could result in run-off from the treated area.

In-line InjectionFor proper use of PHANTOM with in-line injection equip-ment refer to the use instructions for the injection equip-ment. Apply the specified volume of PHANTOM dilutionand active ingredient as set forth in the Directions forUse on this label.

Desired DilutionConcentration*

Amount ofPHANTOM to

make 100 gallonsof finished dilution

Amount ofPHANTOM to

make 1 gallon offinished dilution

0.25%150 fl oz(1.2 gal)

4.4 L 1.5 fl oz 44 ml

0.125% 75 fl oz 2.2 L 0.75 fl oz 22 ml

*Percentage weight of active ingredient to weight of spray dilution

4

PRE-CONSTRUCTION TREATMENT

DO NOT APPLY AT A LOWER DOSAGE AND/ORCONCENTRATION THAN SPECIFIED ON THIS LABELFOR APPLICATIONS PRIOR TO INSTALLATION OFTHE FINISHED GRADE.

Prior to each application, applicators must notify the gen-eral contractor, construction superintendent, or similarresponsible party, of the intended PHANTOM®

termiticide-insecticide application and intended sites ofapplication and instruct the responsible person to notifyconstruction workers and other on site individuals to leavethe treatment area and not return until PHANTOM hasbeen absorbed into the soil.

General:Pre-construction treatments are defined to include treat-ments made during all phases of construction up to andincluding installation of the final grade.

Concrete Slab-on-Ground:

Horizontal Treated ZonesApply a 0.25% dilution of PHANTOM to the entire surfaceof soil or substrate to be covered beneath the concreteslab. This includes the slab under the actual living area,plus carports, porches, basement floors, and any extend-ed entrances. Make this treatment at the rate of 1 gallonfinished dilution per 10 square feet. Make these applica-tions using a coarse spray nozzle and low-pressure spray(less than 25 p.s.i.), spraying the dilution evenly and uni-formly over the entire area treated.

Vertical Treated ZonesPrior to pouring the concrete slab, apply a 0.25%PHANTOM dilution along the inside of foundation walls offloating and supported slabs and around plumbing, bathtraps, utility services, and other features that will penetratethe slab. Apply 4 gallons of finished dilution per 10 linearfeet per foot of depth.

During or soon after completion of the final grading, applya 0.25% dilution of PHANTOM along the outside founda-tion perimeter at the rate of 4 gallons finished dilution per10 linear feet, per foot of depth, or if the footing is morethan 4 feet below grade, to a minimum depth of 4 feetbelow grade.

Apply vertical treatments by trenching or trenching androdding using low pressure spray equipment (less than 25p.s.i. at the nozzle).

• Rod holes and trenches must not extend below the bot-tom of the footing.

• Rod holes must be spaced so as to achieve a continu-ous treated zone but in no case more than 12 inchesapart.

• Trenches must be a minimum of 6 inches deep or to thebottom of the footing, whichever is less, and need notbe wider than 6 inches. When trenching in sloping(tiered) soil, the trench must be stepped to ensureadequate distribution and to prevent termiticide from

running off. The finished dilution should be mixed withsoil as it is replaced in the trench.

Crawl Spaces:For the interior areas of crawl spaces, apply a verticaltreatment of a 0.25% dilution of PHANTOM along theinside foundation perimeter and around all piers andpipes. Apply 4 gallons of finished dilution per 10 linear feetper foot of depth.

During or soon after completion of the final grading, applya 0.25% dilution of PHANTOM along the outside founda-tion perimeter at the rate of 4 gallons finished dilution per10 linear feet, per foot of depth, or if the footing is morethan 4 feet below grade, to a minimum depth of 4 feetbelow grade.

Apply by trenching or trenching and rodding using lowpressure spray equipment (less than 25 p.s.i. at thenozzle).

• Rod holes and trenches must not extend below thebottom of the footing.

• Rod holes must be spaced so as to achieve acontinuous treated zone but in no case more than12 inches apart.

• Trenches must be a minimum of 6 inches deep or to thebottom of the footing, whichever is less, and need notbe wider than 6 inches. When trenching in sloping(tiered) soil, the trench must be stepped to ensureadequate distribution and to prevent termiticide fromrunning off. The finished dilution should be mixed withsoil as it is replaced in the trench.

When treating foundations deeper than 4 feet, apply thetermiticide as the backfill is being replaced, or if the con-struction contractor fails to notify the applicator to permitthis, treat the foundation to a minimum depth of 4 feetafter the backfill has been installed. The applicator musttrench and rod into the trench or trench along the founda-tion walls and around pillars and other foundation ele-ments, at the rate prescribed from grade to a minimumdepth of 4 feet. When the top of the footing is exposed,the applicator must treat the soil adjacent to the footing toa depth not to exceed the bottom of the footing. However,in no case should a structure be treated below the footing.

Hollow Block Foundation or Voids:Hollow block foundations or voids in masonry resting atopthe footing may be treated in order to create a continuoustreatment zone in the area to be treated. Applicators maydrill and treat into voids of masonry elements if not openlyaccessible. Apply at the rate of 2 gallons of finished dilu-tion per 10 linear feet using a nozzle pressure of 25 p.s.i.or less. When using this treatment, access holes may bedrilled below the sill plate and should be as close as pos-sible to the footing as is practical. Treatment of voids inblock or rubble foundation walls must be closely exam-ined: Applicators must inspect areas of possible runoff asa precaution against application leakage in the treatedareas. Some areas may not be treatable or may requiremechanical alteration prior to treatment.

5

All leaks resulting in the deposition of PHANTOM®

termiticide-insecticide in locations other than those pre-scribed on this label must be cleaned up prior to leavingthe application site. DO NOT allow people or pets to con-tact contaminated areas or to reoccupy the contaminatedareas of the structure until the clean up is completed.

Not for use in voids insulated with rigid foam.

POST-CONSTRUCTION SOIL TREATMENT

For applications made after the final grade is installed forthe purpose of protecting the structure from termite infes-tation and/or for controlling existing termite populations.

General Directions for Soil Treatments:DO NOT make treatment beneath slabs or similar floor-ings until the locations of heat or air conditioning duct-work, vents, water and sewer lines, and electricallines/conduits are known and identified. Use extreme cau-tion to avoid puncturing and contaminating these utilities.

The applicator must trench and rod into the trench ortrench along the foundation and around pillars and otherfoundation elements, at a rate prescribed from grade tothe top of the footing. When footing is more than four (4)feet below grade, the applicator must trench and rod intothe trench or trench along the foundation walls at the rateprescribed to a minimum depth of four (4) feet. When thetop of the footing is exposed, the applicator must treat thesoil adjacent to the footing to a depth not to exceed thebottom of the footing; dig a trench alongside the footingtaking care not to undermine the footing. However, in nocase should a structure be treated below the footing.When soil type and/or conditions make trenching prohibi-tive, rodding alone may be used with rod holes no morethan 12 inches apart.

Exterior concrete structures adjoining the foundation, suchas patios, porches and sidewalks, may be drilled followedby treatment by sub-slab injection of the PHANTOM dilu-tion in order to complete the exterior perimeter treatmentzone along the foundation wall.

NOTE: Read and follow the mixing and use directionssection of the label if situations are encountered where thesoil will not accept the full application volume.

Accessible Crawl Spaces:BEFORE TREATMENT: Turn off any air circulation sys-tem that moves air from area to be treated to an untreatedinterior space of the structure until application has beencompleted and all PHANTOM has been absorbed by thesoil.

For crawl spaces, apply vertical termiticide treatments atthe rate of 4 gallons of dilution per 10 linear feet per footof depth from grade to the top of the footing, or if thefooting is more than 4 feet below grade, to a minimumdepth of 4 feet. Apply by trenching and rodding into thetrench, or trenching. Treat both sides of the foundationand around all piers and pipes.

When the top of the footing is exposed, the applicatormust treat the soil adjacent to the footing to a depth notto exceed the bottom of the footing. Read and follow mix-ing and use directions on this label if situations areencountered where the soil will not accept the full applica-tion volume.

1. Rod holes and trenches must not extend below thebottom of the footing.

2. Rod holes must be spaced so as to achieve a continu-ous treated zone, but in no case more than 12 inchesapart.

3. Trenches must be a minimum of 6 inches deep or tothe bottom of the footing, whichever is less, and neednot be wider than 6 inches. When trenching in sloping(tiered) soil, the trench must be stepped to ensure ade-quate distribution and to prevent dilution from runningoff. The PHANTOM dilution must be mixed with the soilas it is replaced in the trench.

4. When unsupported termite tubes are present, mechani-cally destroy each tube and make a horizontal treat-ment by applying approximately 1 gallon of dilution persquare foot, treating an area of no more than 18 inchesin diameter where the tubes emerge from the soil.

Inaccessible Crawl Spaces:BEFORE TREATMENT: Turn off any air circulation sys-tem that moves air from the area to be treated to anuntreated interior space of the structure until applicationhas been completed and all PHANTOM has beenabsorbed by the soil.

For inaccessible interior areas, such as areas where clear-ance between floor joists and ground surfaces is insuffi-cient to allow operator access, excavate, if possible, andtreat according to the instructions for Accessible CrawlSpaces (above). Otherwise, apply one, or a combinationof the following two methods.

1. To establish a horizontal treated zone, apply dilution tothe soil surface at a rate of 1 gallon of dilution per10 square feet using low pressure (less than 25 p.s.i. atthe treating tool when valve is open) and a coarse appli-cation nozzle (e.g. Delavan Type RD Raindrop®, RD-7or larger, or Spraying Systems Co. 8010LP TeeJet® orcomparable nozzle). For an area that cannot bereached with the application wand, use one or moreextension rods to make the application to the soil.DO NOT broadcast or power spray with higherpressures.

2. To establish a horizontal treated zone, drill through thefoundation wall or through the floor above and treat thesoil perimeter at a rate of 1 gallon of dilution per10 square feet. Drill spacing must be at intervals not toexceed 16 inches; many states have smaller intervalsso check state regulations which may apply.

6

Slab-on-Ground (Including Monolithic, Floating andSupported Concrete Slabs):EXTERIOR PERIMETER - Apply by trenching and rod-ding into the trench or trenching around the foundation atthe rate of 4 gallons finished dilution per 10 linear feet perfoot of depth, or if the footing is more than 4 feet belowgrade, to a minimum depth of 4 feet. Trenches must be aminimum of 6 inches deep or to the bottom of the footingand need not be wider than 6 inches. The finished dilutionshould be mixed with the soil as it is replaced in thetrench. Rod holes must be spaced so as to achieve acontinuous treated zone but in no case more than 12inches. However, in no case should the structure be treat-ed below the footing.

SUB-SLAB INJECTION - Sub-slab injection treatmentscan be made from inside the structure or by drillingthrough the foundation from the outside as directed below.Prior to making any treatments, locate all heating/air con-ditioning ducts, vents, water/sewer lines, and electricallines/conduit.

• Vertical Drilling/Injection - To treat under the slab, drillvertically through the slab along the interior perimeter ofthe foundation, including the garage. Drill holes along allconcrete expansion joints, cracks, plumbing, and utilityservices penetrating the slab. It may be necessary to drillholes along one side of the slab adjacent to an interiorpartition wall if there is clear evidence of termite activityor damage in the wall. All drill holes through the slabshould be spaced so as to achieve a continuous treatedzone, but in no case be more than 12 inches apart.Inject PHANTOM® termiticide-insecticide finisheddilution into the drilled holes at the rate of 4 gallons per10 linear feet per foot of depth. For best results, applica-tion should be made with a lateral dispersal nozzle. Allholes in commonly occupied areas into which materialhas been applied must be plugged. Plugs must be of anon-cellulose material or covered by an impervious, non-cellulose material.

A horizontal treated zone can also be establishedbeneath the slab using the above technique as a gridpattern injection. Otherwise, use the methods describedbelow.

• Horizontal Drilling/Rodding/Sub-slab InjectionFrom the Exterior of the Foundation - This techniqueshould be used to treat underneath the slab only whenfloors or interior design do not allow for vertical drilling.Care must be exercised not to rod into heating ducts,water/sewer lines, and electrical lines/conduits.Horizontal short-rodding practices can be used toestablish a continuous treated zone along the insideperimeter of the foundation. Holes should be drilled fromoutside the foundation at an angle which allows afinished dilution of PHANTOM to be deposited belowheating ducts, water/sewer lines, and electrical conduits,if present. Horizontal long rodding practices may only beemployed to treat areas underneath the slab that are notaccessible by vertical rodding or horizontal short rod-

ding. Long rods exceeding 20 feet should not be used.For all horizontal rodding applications, all drill holesthrough the foundation should be spaced so as toachieve a continuous treated zone but in no case bemore than 12 inches apart. Inject dilution containingPHANTOM into the drilled holes at the rate of 4 gallonsper 10 linear feet per foot of depth. For best results,make applications with a lateral dispersal nozzle. Allholes must be plugged. Plugs must be of a non-cellu-lose material or covered by an impervious, non-cellulosematerial.

Bath Traps: Treat exposed soil or soil covered with tar ora similar type sealant beneath and around plumbingand/or drain pipe entry areas. Apply PHANTOM finisheddilution at a minimum of 1 gallon but no more than 4 gal-lons of dilution per square foot. An access door or inspec-tion portal should be installed, if not already present. Afterinspection and removal of any wood or cellulose debris,the soil can be treated by rodding or drenching the soilwith a 0.125% or 0.25% dilution of PHANTOM.

Buildings on Soil: In treating areas under wooden floorsor other materials, with the exception of concrete ormasonry, laying directly on or in close proximity to the soil(such as gymnasium floors, finished family rooms or similarareas converted to living areas where joists are placed onthe ground and flooring placed on top), the floor should bedrilled on a squared-grid pattern, 12-18 inches on center,and the dilution containing PHANTOM then applied overthe soil surface at the rate of 1 gallon dilution per10 square feet to provide a uniform treated zone. Wherethere is exposed soil beneath and around plumbing/wastepipe entrances, thoroughly treat using 1 gallon of dilutionper 10 square feet to provide a uniform treated zone.

Basements - Outside Perimeter: Along the outside ofthe exterior walls, apply 4 gallons of dilution per 10 linearfeet per foot of depth from grade to the top of the footing,or if the footing is more than 4 feet below grade, to a mini-mum depth of 4 feet. Apply by trenching and rodding intothe trench, or trenching. Trenches must be at least 6 inch-es wide and at least 6 inches deep. When roddingthrough a trench, apply dilution to the soil with the appli-cation rod at 12 inch or less intervals. Use low pressurespray to treat soil as it is replaced into the trench. Whentrenching in sloping (tiered) soil, the trench must bestepped to ensure adequate distribution and to preventthe dilution from running out of the trench.

Basements - Inside Perimeter: If a well or cistern ispresent, refer to Wells/Cisterns section of this label. Totreat under the basement floor slab, drill vertically throughthe slab along the interior perimeter of the foundation. Drillholes along all concrete expansion joints, cracks, plumb-ing, and utility services penetrating the slab. Drill holesalong both sides of partition foundation walls, and aroundpiers. It may be necessary to drill holes along one side ofthe slab adjacent to a non-foundation interior partition wallif there is clear evidence of termite activity in the wall. Alldrill holes through the slab should be spaced so as to

7

achieve a continuous treated zone but in no case be morethan 12 inches apart. Inject finished dilution containingPHANTOM® termiticide-insecticide into the drilledholes at the rate of 4 gallons per 10 linear feet per foot ofdepth. For best results, application should be made with alateral, dispersal nozzle. All holes in commonly occupiedareas into which material has been applied must beplugged. Plugs must be of a non-cellulose material or cov-ered by an impervious, non-cellulose material.

Hollow Block Foundation or Voids: Hollow block foun-dations or voids in masonry resting atop the footing maybe treated. Drill and treat voids in multiple masonry ele-ments of the structure extending from the structure to thesoil in order to create a continuous treatment zone in thearea to be treated. Applicators may drill and treat intovoids of masonry elements if not openly accessible. Applyat the rate of 2 gallons of finished dilution per 10 linear feetof footing using a nozzle pressure of 25 p.s.i. or less.When using this treatment, access holes may be drilledbelow the sill plate and should be as close as possible tothe footing as practical. Treatment of voids or block orrubble foundation walls must be closely examined.Applicators must inspect areas of possible runoff as a pre-caution against application leakage in the treated areas.Some areas may not be treatable or may require mechani-cal alteration prior to treatment.

All leaks resulting in the deposition of dilution containingPHANTOM in locations other than those prescribed onthis label must be cleaned up prior to leaving the applica-tion site. DO NOT allow people or pets to contact con-taminated areas or to reoccupy the contaminated areas ofthe structure until the clean up is completed.


FOAM APPLICATIONSWhen treating voids with soil below, at least 75% of thegallons of the finished dilution containing PHANTOMshould be applied as a typical liquid treatment to the soil.The remaining 25% or less gallons may be delivered toappropriate locations using a foam application. The totalamount of product applied with the combination of foamand liquid finished dilution should be equivalent to that ofthe application of liquid finished dilution only.

Foam applications are generally a good supplement to liq-uid treatments in difficult areas, but may also be used indifficult to access spot or partial treatments. Constructionpractices, soil subsidence and other factors may make itdifficult to create a continuous treatment zone. When nec-essary, conventional treatments may be supplementedthrough the use of foam-generating equipment or similardevices to provide a continuous treated zone. Applicationexamples may include; treatment behind veneers, piers,chimney bases, into rubble foundations, into block voids,structural voids, wall voids, under slabs, stoops, porches,or to the soil in inaccessible crawl spaces and other simi-lar voids.

Foam applications to wall voids and stud walls that do nothave a soil base should utilize dry foam only (15:1 to 50:1expansion ratio).

Foam applications to voids above soil should be done witha wet foam (10:1 expansion ratio or less).

Foam Application Use Directions: Mix appropriate con-centration of PHANTOM in water and add the manufactur-er’s recommended quantity of foam agent to thePHANTOM dilution (see table for foaming recommenda-tions). It is highly recommended that applicators use a non-repellent foaming agent with PHANTOM. Apply a sufficientvolume of PHANTOM in foam alone or in combination withliquid dilution to provide a continuous treated zone at therecommended rate for specific application sites.

Mixing Table for PHANTOM Foam

Plenums:BEFORE TREATMENT: Turn off any air circulation sys-tem that moves air from the space to be treated to anuntreated interior space of the structure until applicationhas been completed and all of the dilution containingPHANTOM has been absorbed by the soil.

For plenum-type structures, apply the dilution at the rateof 4 gallons of dilution per 10 linear feet, per foot of depthof soil to provide a uniform treated zone adjacent to bothsides of foundation walls, supporting piers, plumbing andconduits. Create a vertical treated zone by trenching androdding into the trench or by trenching around the founda-tion; trench must be about 6 inches wide and at least 6inches deep. Use a low pressure spray to treat soil whichwill be replaced into the trench after rodding; mix dilutionwith the soil as it is being replaced into the trench.

When conditions will not permit trenching or rodding, asurface application adjacent to interior foundation wallsmay be made, but the treated zone shall not exceed awidth of 18 inches, horizontally, from the foundation walls,piers, or pipes. The surface application should be made ata rate of 1 gallon of dilution per 10 square feet as a verycoarse spray under low pressure (not to exceed 25 p.s.i.when measured at the treating tool when valve is on).

PHANTOMUse Dilution

Gallons ofFinishedDilution

FoamExpansion

Ratio*

FinishedFoam

(gallons)

0.125% or0.25%

0.25(32 fl oz)

10:1 2.5

0.125% or0.25%

1.01.251.662.55.0

25:120:115:110:15:1

25

* Add the manufacturer’s recommended quantity of foam agent to thePHANTOM dilution. It is highly recommended that applicators use anon-repellent foaming agent with PHANTOM. Amount of finisheddilution can be increased or decreased to allow for a different amountof finished foam at the selected expansion ratio.

8

Follow the instructions below for interior treatment ofplenum structures that use a sealed under-floor space tocirculate heat and/or cooled air throughout the structure.

1. Remove the sealing fabric and anything on the sealingfabric to expose no more than 18 inches adjacent to all foundation structures, including foundation walls, interi-or piers, pipes, and any other structures with soil con-tact. Follow the instructions listed above for exterior andinterior treatment of “Accessible Crawl Spaces”.

2. After the finished dilution containing PHANTOM®

termiticide-insecticide has been absorbed by thesoil, replace the sealing fabric and anything to beplaced on the sealing fabric to its original, pre-treatmentposition.

TREATMENT OF STRUCTURES WITH WELLS ORCISTERNS:DO NOT contaminate wells or cisterns.

Structures with Wells/Cisterns Inside Foundations:DO NOT apply PHANTOM dilution within 5 feet of anywell or cistern. Soil within 5 to 10 feet from a well or cis-tern must only be treated by the backfill method.Treatment of soil adjacent to water pipes within 3 feet ofgrade must only be done by the backfill method. Infestedand/or damaged wood should be replaced or repaired.

Treated Backfill Method: Where treatment must bemade in difficult situations, such as near wells, cisterns,along fieldstone or rubble walls, and around pipes and util-ity lines which lead to a well or pond, applications may bemade in the following manner:

1. Trench and remove soil to be treated onto heavy plasticsheeting, similar material or into a wheel barrow.

2. Treat the soil at the rate of 4 gallons of dilution per10 linear feet per foot of depth of the trench, or 1 gallonper 1 cubic foot of soil. Mix the dilution thoroughly intothe soil, taking care to prevent runoff or spillage.

3. After the treated soil has absorbed the dilution, replacethe soil in the trench. Prior to using this technique nearwells or cisterns, consult federal, state, county, or localagencies, including the state Wellhead ProtectionProgram, for information regarding approved treatmentpractices in your area.

Structures with Adjacent Wells/Cisterns and/orOther Bodies of Water: Applicators must inspect allstructures with nearby water sources such as wells, cis-terns, surface ponds, streams, and other bodies of waterand evaluate, at a minimum, the treatment recommenda-tions listed below prior to making an application.

1. Treatment of soil adjacent to the water pipe(s) shouldbe done according to the backfill method. Prior to treat-ment, if feasible, expose the water pipe(s) coming fromthe well to the structure, if the pipe(s) enter the struc-ture within 3 feet of grade.

2. Prior to treatment, applicators are advised to take pre-cautions to limit risk of applying termiticide into subsur-face drains that could empty into any bodies of water.These precautions include evaluating whether applica-

tion of the termiticide to the top of the footer may resultin contamination of the subsurface drain. Factors suchas depth to the drain system and soil type and degreeof compaction should be taken into account in deter-mining the depth of treatment.

3. When appropriate (i.e. on the side of the structure clos-est to the water), the treated backfill method (describedabove) can be used to further minimize off-site move-ment of termiticide.

4. DO NOT apply to drainage systems such as sumps,French drains, leach beds, or other effluent dischargesystems.

Retreatments: Subsequent to the initial treatment,retreatments for subterranean termites can only be per-formed if there is clear evidence of reinfestation, or disrup-tion of the treated zone due to construction, excavation,landscaping, and/or evidence of the breakdown of the ter-miticide treated zone in the soil. Those vulnerable or rein-fested areas may be retreated in accordance with applica-tion techniques described in this product’s labeling.Retreatments may be made as either a spot, partial orcomplete treatment(s). The timing and type of theseretreatments will vary, depending on factors such as ter-mite pressure, soil types, soil conditions and other factorswhich may reduce the effectiveness of the treated zone.Annual retreatment of the structure is prohibited unlessthere is clear evidence of reinfestation or if disruption hasoccurred.

Above-Ground Termite Infestations: PHANTOM canalso provide localized control of southeastern drywoodtermite (Incisitermes snyderi) and subterranean termites intheir above-ground galleries, workings or aerial nests with-in the structure. Apply either a 0.125% or 0.25% dilutionby foam and/or liquid injection into galleries, nesting areasand infested voids or channels in damaged wooden mem-bers of a structure, or to other locations vulnerable toattack by termites. Locate existing openings, or drill theinfested cavity, and inject dilution under low pressure usingappropriate treatment tools. Plug treatment holes drilled incommonly occupied areas of structures. Inspect as need-ed. DO NOT reapply more often than every four weeks.

GENERAL INFORMATIONPHANTOM is intended for sale, use and storage only byindividuals/firms licensed or registered by the state toapply termiticide and/or general pest control products as aspot or crack and crevice spray for residual pest control.Permitted areas of use include: Inside houses, apart-ments or other residential structures, meat, poultry & eggprocessing & packaging plants, the food/feed- and non-food/feed-handling areas of food-handling establishmentsand commercial, institutional and warehousingestablishments.

Food-handling Establishments include places other thanprivate residences where exposed food is held,

USE DIRECTIONS FOR GENERAL PEST CONTROL

9

processed, prepared or served. These include food serv-ice, manufacturing and processing establishments such asrestaurants, cafeterias, supermarkets, mills, processingplants, bakeries, breweries, dairies, meat slaughtering andpacking plants and canneries.

Commercial, institutional and warehousing establishmentsinclude schools, groceries and supermarkets, restaurantsand cafeterias, hotels and motels, hospitals and nursinghomes, warehouses and industrial buildings, laboratories,zoos, pet shops, computer facilities, and sewers.

MIXING DIRECTIONS

Dilution Table:

Mix the dilution in the following manner:1. Fill hand-pressurized or power-operated application

equipment with 1/2 to 3/4 of the required amount ofwater.

2. Measure the required amount of PHANTOM.3. Add PHANTOM to the sprayer and fill with the remain-

der of the water.4. Close sprayer and agitate to insure proper suspension.5. Re-agitate material in sprayer before continuing if appli-

cation is interrupted.

GENERAL PEST CONTROL

PHANTOM can be used to control many nuisance pests,stored product pests and occasional invaders that infeststructures, including:• ants (acrobat, Argentine, carpenter, odorous house,

pavement, pharaoh’s, pyramid);• beetles (Asian lady, confused flour, darkling larva (yellow

mealworm), saw-toothed grain);• bark scorpions;• bed bugs,• boxelder bugs,• centipedes;• cockroaches (American, Asian, brown-banded, German,

Oriental, and smokybrown);• European earwigs;• house crickets;• house flies;• paper wasps*• pillbugs;• spiders (black widow, cellar);• silverfish

*PHANTOM is not a knockdown agent.

Desired DilutionConcentration*

Amount of PHANTOM®

termiticide-insecticideto make 1 gallon of

finished dilution

Amount of PHANTOM to

make 5 gallonsof finished

dilution

0.50% 3.0 fl oz 88 ml 15.0 fl oz 440 ml

*Percentage weight of active ingredient to weight of spray dilution.GENERAL PRECAUTIONS FOR

GENERAL PEST CONTROL

DO NOT make general surface or space applicationssuch as for pantry pests in cupboards, cabinets or incontainers.

DO NOT contaminate food or food contact surfaces.

DO NOT apply into heating and air conditioning vents orducts.

Individuals without proper personal protective equipmentshould not be in immediate vicinity during application.

DO NOT contact treated areas until spray has dried.

Use only in well ventilated conditions. In hospitals andnursing homes, remove patients before treating rooms.Allow treated areas to dry before returning patients totreated rooms.

DO NOT apply to aircraft cabins.

DO NOT allow for contact to treated areas until sprayhas dried. Allow treated surfaces to dry before replacingitems.

Remove pets and cover or remove pet food/water andfish bowls prior to application.

In zoos, remove animals and cover or remove animalfood/water prior to application.

DO NOT apply in patient rooms or classrooms while inuse.

DO NOT apply water-based sprays where electricalshort circuits could occur.

DO NOT make surface applications to mattresses.Mattress treatments must be confined to the seams,folds and edges only. Remove linens and wash beforereuse. Allow to dry before remaking bed.

10

Apply a 0.5% dilution as a coarse, low-pressure spot orcrack and crevice spray.

For use with low-pressure directed spray or similar appli-cation equipment. Use a straw tip or pin tip nozzle forcrack and crevice applications. Application shall be limitedto a maximum 0.5% concentration.

Spot or crack and crevice treatments of PHANTOM®

termiticide-insecticide dilution can be made to breedingareas, nesting sites, hiding places, runways, and otherplaces where pests are found or can infest. Apply to sur-faces beneath cabinets, spaces between equipment orexpansion joints, surfaces behind sinks, lockers, waterpipes, cabinets, or other pest hiding areas. Where possi-ble, apply PHANTOM directly to ant nest(s) or nestingsite(s), ant trails or ant-infested wood or structural voids.Foam applications of PHANTOM may be made in voids.

DO NOT reapply more often than every four weeks.

Interior Applications in Non-Food-Handling AreasSpot or crack and crevice applications may be made innon-food/feed areas such as garbage rooms, lavatories,floor drains (to sewers), entries, and vestibules, offices,locker rooms, machine rooms, boiler rooms, garages,mop closets and storage.

Interior Applications in Food-Handling AreasFood-handling areas are areas where food and food prod-ucts are held, processed, prepared or served. Applicationin food-handling areas of food-handling establishments islimited to spot or crack and crevice treatments. The food-handling area may not be in operation during application.Exposed food must be covered or removed prior to appli-cation. After application, all food contact surfaces in thetreated areas must be washed with an effective cleaningcompound followed by a potable water rinse beforeresuming food operations. DO NOT apply directly to food,food packaging or food contact surfaces.

Limited Exterior Application to StructuresExterior application is limited to spot and crack andcrevice treatments where pests enter around doors, win-dows, eaves, attic vents, and holes in exterior walls whereutilities enter. Apply a maximum of 1.2 fl oz of dilution per2 square feet.

11

LABEL LICENSE FOR PHANTOM® TERMITICIDE-INSECTICIDE

Phantom is specially formulated and sold by BASF for thecontrol of termites and other insect pests according to theDirections For Use on this label. The purchase price ofPhantom includes a royalty whereby the purchaseracquires a prepaid license under U.S. Patent Nos.5,310,938; 6,077,863; 6,071,951; 5,496,845; 6,242,613;and 6,417,372 under which purchaser agrees to employthe purchased quantity of Phantom only for the above-specified uses under BASF’s United States patent rightsand to provide notice of the terms and conditions of thislicense to any subsequent purchaser. Uses of Phantomother than those specified on this label are not licensedthrough the purchase of this product and the use of thisproduct for other purposes may violate this license andpatent rights of BASF.

Phantom cannot be used to formulate or reformulate anyother pesticide product.

Conditions of Sale and WarrantyThe Directions For Use of this product reflect theopinion of experts based on field use and tests. Thedirections are believed to be reliable and must befollowed carefully. However, it is impossible to eliminateall risks inherently associated with the use of thisproduct. Crop injury, ineffectiveness or other unintendedconsequences may result because of such factors asweather conditions, presence of other materials, or useof the product in a manner inconsistent with its labeling,all of which are beyond the control of BASFCORPORATION (“BASF”) or the Seller. To the extentconsistent with applicable law, all such risks shall beassumed by the Buyer.

BASF warrants that this product conforms to thechemical description on the label and is reasonably fitfor the purposes referred to in the Directions For Use,subject to the inherent risks, referred to above.

To the extent consistent with applicable law, BASFmakes no other express or implied warranty of fitnessor merchantability or any other express or impliedwarranty.

To the extent consistent with applicable law, Buyer’sexclusive remedy and BASF’s exclusive liability, whetherin contract, tort, negligence, strict liability, or otherwise,shall be limited to repayment of the purchase price ofthe product.

To the extent consistent with applicable law, BASF andthe Seller disclaim any liability for consequential, specialor indirect damages resulting from the use or handlingof this product.

BASF and the Seller offer this product, and the Buyerand User accept it, subject to the foregoing Conditionsof Sale and Warranty which may be varied only byagreement in writing signed by a duly authorizedrepresentative of BASF. 0408

Phantom is a registered trademark of BASF.Raindrop is a registered trademark of Delavan Corporation.TeeJet is a registered trademark of Spraying Systems Company.

© 2011 BASF CorporationAll rights reserved.

000241-00392.20110125.NVA 2010-04-155-0181Based on: NVA 2010-04-155-0180

Supersedes: NVA 2008-04-155-0124

BASF Corporation26 Davis Drive

Research Triangle Park, NC 27709

12

ACTIVE INGREDIENTS:(S)-Methoprene (CAS #65733-16-6) . . . . . . 0.085%Permethrin (CAS #52645-53-1). . . . . . . . . 0.350%Phenothrin (CAS #26002-80-2) . . . . . . . . . 0.300%N-octyl bicycloheptene dicarboximide

(CAS #113-48-4) . . . . . . . . . . . . . . . . 2.000%Piperonyl butoxide, Technical*

(CAS #51-03-6) . . . . . . . . . . . . . . . . . . 1.400%OTHER INGREDIENTS**: . . . . . . . . . . . . . . 95.865%TOTAL: . . . . . . . . . . . . . . . . . . . . . . . . . 100.000%* Consists of 1.120% (butylcarbityl)(6-propylpiperonyl) ether and 0.280%related compounds. **Contains petroleum distillates.

EPA Reg No. 2724-490


SEE ADDITIONAL PRECAUTIONARY STATEMENTS

INTRODUCTIONPrecor 2000® Plus kills adult fleas, hatching flea eggs,flea larvae, and ticks. PRECOR®, the unique ingredientin Precor 2000® Plus provides 210 days’ protection bypreventing eggs from ever developing into biting fleas.For best results, use Precor 2000® Plus with Petcor® on-animal products for complete control of fleas and ticks.READ ENTIRE LABEL BEFORE USE. NOT FOR USE ONHUMANS OR PETS.

PRECAUTIONARY STATEMENTSHAZARDS TO HUMANS AND

DOMESTIC ANIMALS – CAUTIONAvoid contact with skin or clothing. Wash handsthoroughly with soap and water after handling and

• TREATS 2000 SQ. FT.• CONTAINS PRECOR® INSECT GROWTH REGULATOR PLUS ADULTICIDES• CONTROLS FLEAS AND TICKS• FAST-ACTING FORMULA• FOR USE IN COMMERCIAL/INDUSTRIAL BUILDINGS• PREVENTS REINFESTATION AND FLEA BUILD-UP FOR 210 DAYS

22000000 PlusPremise Spray

before eating, drinking, chewing gum, using tobacco,or using the toilet. Prolonged or frequently repeatedskin contact may cause allergic reactions in someindividuals.

FIRST AIDIf on skin or clothing • Take off contaminated

clothing.• Rinse skin immediately with

plenty of water for 15-20minutes.

• Call a poison control centeror doctor for treatmentadvice.

If swallowed • Call a poison control centeror doctor immediately fortreatment advice.

•Do not induce vomit ingunless told to do so by apoison control center ordoctor.

• Do not give ANY liquid tothe person.

• Do not give anything bymouth to an unconsciousperson.

In case of emergency, call 1-800-248-7763 or apoison control center. Have the product container orlabel with you when calling a poison control centeror doctor or going for treatment.NOTE TO PHYSICIAN/VETERINARIAN: Containspetroleum distillates – vomiting may cause aspirationpneumonia.

Return to Index...

PHYSICAL OR CHEMICAL HAZARDSContents under pressure. Do not use or store near heator open flame. Do not puncture or incineratecontainer. Exposure to temperatures above 130°F maycause bursting.

DIRECTIONS FOR USEIt is a violation of Federal Law to use this product in amanner inconsistent with its labeling.SHAKE WELL BEFORE USING.

FOR USE IN THE HOME/GARAGE/KENNEL

1. Identify treatment areas, especially those wherepets frequent, such as in and around pet’s sleepingand resting areas. These are the primary areaswhere fleas, their eggs, and ticks are found. Beforetreatment, make a test application to upholstery,drapery, light-colored, delicate fabrics, or woodsurfaces in an inconspicuous place.

2.Prepare treatment areas. Cover all food processingsurfaces and utensils during treatment or thoroughlywash after product use. Cover or remove exposedfood. Remove pets, and cover and unplugaquariums before spraying. Remove motor vehiclesbefore using in garages. For best results withSurface/Carpet treatments, vacuum thoroughlybefore spraying and discard vacuum bag in outsidetrash. This product may also be used for infestedsurfaces inside motor vehicles.

3.Apply treatment. For flea/tick infestations, a singlecan treats 2000 square feet. Hold container upsidedown 2-3 feet from surface, point actuator towardsthe surface and push button. Using a sweepingmotion, apply a light, uniform spray to all surfacesof furniture, rugs, carpets, drapes, and around allpet resting areas. Avoid thoroughly wett ingsurfaces. Mist treated areas only until "slightlydamp". Do not over-treat. Reapply in 14 days, ifnecessary. IMPORTANT: Only complete and properapplication to carpets, upholstery, drapes, andother fabrics will provide thorough flea/tickelimination. Keep people and pets out of areasduring treatment. Vacate room after treatment, andventilate until surfaces are dry before reoccupying.

4.For best results, eliminate fleas/ticks on pets withappropriate Petcor® on-animal products.

300504625

Precor 2000, Precor, and Petcor and the Zoecon logoare registered trademarks of Wellmark International.©1998-2009 WELLMARK INTERNATIONAL

October, 2009Schaumburg, IL

FOR USE IN HOSPITALS, HOTELS, MOTELS, OFFICES,SCHOOLS, SUPERMARKETS, TRANSPORTATIONEQUIPMENT (BUSES, BOATS, SHIPS, TRAINS, TRUCKS),WAREHOUSES, UTILITIES, VETERINARY CLINICS ANDOTHER COMMERCIAL AND INDUSTRIAL BUILDINGS

1.Prepare treatment areas. For best results withSurface/Carpet treatments, vacuum thoroughlybefore spraying and discard vacuum bag in outsidetrash. Test in an inconspicuous area beforetreating. Cover all food processing surfaces andutensils during treatment or thoroughly wash afterproduct use. Cover or remove exposed food. Keeppeople and pets out of areas during treatment.Cover and unplug aquariums before spraying.Vacate room after treatment, and thoroughlyventilate until surfaces are dry before reoccupying.

2.Apply treatment. For flea/tick infestations, a singlecan treats 2000 square feet. Hold container upsidedown 2-3 feet from surface, point actuator towardsthe surface and push button. Using a sweepingmotion, apply a light uniform spray to all surfaces offurniture, rugs, carpets, drapes, and around all petresting areas. Avoid thoroughly wetting surfaces.Mist treated areas only until “slightly damp”. Donot over-treat. Reapply in 14 days, if necessary.IMPORTANT: Only complete and proper applicationto carpets, upholstery, drapes, and other fabrics willprovide thorough flea/tick elimination.

STORAGE AND DISPOSALStorage: Store in a cool, dry area. Do not transport orstore below 32°F. Disposal: Do Not Puncture orIncinerate! If empty: Place in trash or offer forrecycling if available. If partly filled: Call your localsolid waste agency for disposal instructions.

WARRANTY AND CONDITIONS OF SALESeller makes no warranty, expressed or implied,concerning the use of this product other than indicatedon the label. Buyer assumes all risks of use andhandling of this material when such use and handlingare contrary to label instructions.For information or in case of emergency, cal l1-800-248-7763.www.zoecon.com

ACTIVE INGREDIENTS:(S)-Methoprene (CAS #65733-16-6). . . . 0.09%Permethrin (CAS #52645 -53-1). . . . . . . 0.58%

OTHER INGREDIENTS: . . . . . . . . . . . . . . . . 99.33%Total . . . . 100.00%

EPA Reg No. 2724 -454


See additional precautionary statements

PRECOR® Plus Fogger (PRECOR) kills adult fleas andtheir hatching eggs. PRECOR® Insect Growth Regulator,the ingredient in PRECO R, provides 7 months’protection by preventing eggs from ever developing intobiting fleas. PRECOR enables you to fill an entire roomwith insect-killing fog while you are away.

DIRECTIONS FOR USEIt is a violation of Federal Law to use this product in amanner inconsistent with its labeling.Do not use in non-enclosed non-food/ feed areas nor infood areas of food/ feed handling establishments (i.e.,restaurants, etc.) including places in which exposedfood is held, processed, prepared, or served. Non-food/ feed areas of food/ feed establishments areareas such as garbage rooms, lavatories, floor drains(to sewers), entries and vestibules, offices, lockerrooms, machine rooms, boiler rooms, garages, mopclosets, and storage (after canning or bottling). Notfor use in USDA meat and poultry plants. In the home,all food processing surfaces and utensils should be

• KILLS ADULT FLEAS AND THEIR HATCHING EGGS• PRECOR® INSECT GROW TH REGULATOR• PREVENTS FLEA REINFESTATION FOR 7 MONTHS• NO LINGERING ODOR OR STAINS• EASY TO APPLY• EFFECTIVELY BREAKS THE FLEA LIFE CYCLE

covered during treatment or thoroughly washed beforeuse. Exposed food should be covered or removed.

SHAKE WELL BEFORE USING1. Vacuum thoroughly before fogging. To ensure

unobstructed flow of fogger mist, open inside doorsand cabinets. Remove or cover exposed food,dishes, utensils, food preparation equipment, andsurfaces. Remove pets and birds and remove orcover (and turn off) aquariums. Close outside doorsand windows. TURN OFF ALL IGNITION SOURCESSUCH AS PILOT LIGHTS (SHUT OFF GAS VALVES),OTHER OPEN FLAMES, OR RUNNING ELECTRICALAPPLIANCES THAT CYCLE OFF AND ON (i.e.,REFRIGERATORS, THERMOSTATS, etc.). Call yourgas utility or management company if you needassistance with your pilot lights.

2. Use 1 container for each 6000 cubic feet of area(a room 30' X 25' with an 8' ceiling). DO NOTUSE MORE THAN 1 FOGGER PER ROOM. DO NOTUSE IN SMALL ENCLOSED SPACES SUCH ASCLOSETS, CABINETS, OR UNDER COUNTERS ORTABLES. DO NOT USE IN A ROOM 5' x 5' ORSMALLER; INSTEAD, ALLOW FOG TO ENTER FROMOTHER ROOMS.

3. Remove all motor vehicles before fogging garage.4. Elevate fogger by placing on stand or table covered

by newspaper in center of room to be fogged.N ewspapers should be spread on the floor forseveral feet around area of release.

5. Before activating, tilt can away from face (containersprays straight up). Press down firmly on edge ofactuator tab until it locks into place.

®

PLUS FOGGER

Return to Index...

6. After activating fogger, leave room or house atonce. Keep treated area closed for at least 2hours, then open all doors and windows and allowtreated area to air for 1 hour before returning.

7. For best results, spot treat with Zoecon® premiseproducts under beds, furniture, or obstructed areaswhere fogger mist may not penetrate.

STORAGE AND DISPOSALSTORAGEStore in a cool, dry area away from heat or openflame. DISPOSALDo Not Puncture or Incinerate!IF EMPTYPlace in trash or offer for recycling if available. IF PARTLY FILLEDCall your local solid waste agency or 1-800-CLEANUPfor disposal instructions.

PRECAUTIONARY STATEMENTS HAZARDS TO HUMANS

AND DOMESTIC ANIMALSCAUTION

USE ONLY WHEN AREA TO BE TREATED IS VACATEDBY HUMANS AND PETS.

Harmful if inhaled, swallowed, or absorbed throughthe skin. Avoid breathing vapors or spray mist. Maycause eye irritation. Avoid contact with eyes, skin,and clothing. Wash thoroughly with soap and waterafter using. Avoid contamination of food, foodstuffs,and food preparation areas. Leave room or house atonce after activating fogger. If pet is exposed to wetsurface, wash fur with soap and water.

FIRST AIDCall a poison control center or doctor immediately fortreatment advice.IF IN EYES • Hold eye open and rinse slowly and

gently with water for 15-20 minutes.

• Remove contact lenses, if present,a fter the f i rst 5 minutes, thencontinue rinsing eye.

IF INHALED • Move person to fresh air.• If person is not breathing, call 911

or an ambulance, then give artificialrespiration, preferably by mouth-to-mouth, if possible.

FIRST AID (CONTINUED)IF SWALLOWED • Have person sip a glass of water if

able to swallow.• Do not induce vomiting unless told to

do so by the poison control center ordoctor.

• Do not give anything by mouth to anunconscious person.

IF ON SKIN • Take off contaminated clothing.OR CLOTHING • Rinse skin immediately with plenty of

water for 15-20 minutes.Have the product container or label with you whencalling a poison control center or doctor, or going fortreatment. You may also contact 1-800-248-7763 foremergency medical treatment information. Contactveterinarian if pets are exposed during application.Note to Physician/ Veterinarian: M ay presentaspiration hazard.

HIGHLY FLAMMABLE INGREDIENTINGREDIENTES ALTAMENTE INFLAMABLE

PHYSICAL OR CHEMICAL HAZARDSExtremely Flammable. Contents under pressure. Keepaway from heat, sparks, and open flame. Do notpuncture or incinerate container. Exposure totemperatures above 130° F may cause bursting. THISPRODUCT CONTAINS A HIGHLY FLAMMABLEINGREDIENT. IT MAY CAUSE A FIRE OR EXPLOSION IFNOT USED PROPERLY. FOLLOW THE "DIRECTIONSFOR USE" ON THIS LABEL VERY CAREFULLY.

WARRANTYSeller makes no warranty, express or implied, concerning the use of this product other thanindicated on the label. Buyer assumes all risk of use and handling of this material whensuch use and handling are contrary to label instructions.

For i nformation or i n case of emergency, ca l l1-800-248-7763 or vi si t our W eb si te:www.zoecon.com.

22-14-033

Zoecon A Wellmark International Brand.PRECOR® and ZOECON® are registered trademarks of Wellmark International.

©2002 W ELLMARK INTERNATIONALJuly 2002

Schaumburg, IL

Wellmark InternationalSchaumburg, Illinois U.S.A.

Made in the USA

For sale to, use and storage only by individuals/firms licensed or registered by thestate to apply termiticide and/or general pest control products.

Contains no CFCs or other ozone depleting substances. Federal regulations prohibitCFC propellents in aerosols.

Broad-spectrum Ready to Use Product

Spot and/or Crack and Crevice Pressurized Spray.

Active Ingredient:Chlorfenapyr: 4-bromo-2-(4-chlorophenyl)-1-(ethoxymethyl)-5-(trifluoromethyl)-1H-pyrrole-3-carbonitrile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5%Other Ingredients: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99.5%Total: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100.0%



CAUTIONSee inside for additional Precautionary Statements, Directions for Use, and Storage and Disposal.

In case of emergency endangering life or property involving this product, call day or night 1-800-832-HELP (4357).

Net Weight:

Prescription Treatment®brand

®

Pressurized Insecticide

BASF Corporation26 Davis DriveResearch Triangle Park, NC 27709

Return to Index...

Kills on direct spray contact the following pests: Ants(Acrobat, Argentine, Odorous House, Pavement, Pharaoh,Pyramid); Beetles (Asian Lady, Confused Flour, DarklingLarva (Yellow Mealworm), Saw-toothed Grain); BarkScorpions; Bed Bugs, Boxelder Bugs, Centipedes;Cockroaches (American, Asian, Brown-Banded, German,Oriental, and Smokey Brown); Earwigs; House Crickets;House Flies; Paper Wasps*, Pillbugs; Spiders (BlackWidow, Cellar); Silverfish; Stored Product Pests; andTermites

*Not a knockdown insecticide.

Precautionary Statements


CAUTION

In case of emergency endangering life or propertyinvolving this product, call day or night 1-800-832-HELP (4357). Have the product containerwith you when calling a poison center or doctor orgoing for treatment.

Personal Protective Equipment (PPE)Applicators must wear: Long-sleeved shirt, long pants,socks, shoes and chemical-resistant gloves (such asbarrier laminate, butyl rubber, selection Category B).

User Safety RequirementsFollow manufacturer's instructions for cleaning/maintainingPPE. If no such instructions for washables exist, usedetergent and hot water. Keep and wash PPE separatelyfrom other laundry.

Use Restrictions

• DO NOT reapply to treated area more than every fourweeks.

• Use only in well-ventilated conditions.

• DO NOT contaminate food or food contact surfaces.

• In hospitals and nursing homes, remove patients beforetreating rooms. Allow treated areas to dry before return-ing patients to treated rooms.

• DO NOT use in schools while occupied. Allow treatedareas to dry before allowing re-occupancy.

• DO NOT contact treated areas until spray has dried.

• Remove pets and cover or remove pet food/water andfish bowls prior to application.

• In zoos, remove animals and cover or remove animalfood/water prior to application.

• DO NOT make general surface or space applicationssuch as, for pantry pests in cupboards, cabinets, or incontainers.

• Applications in food-handling areas of food-handling establishments are limited to spot and/orcrack and crevice treatments. The food-handling areamay not be in operation during application. Exposedfood must be covered or removed prior to application.

• DO NOT apply directly to food, food packaging, or foodcontact surfaces.

• After application, all food contact surfaces in the treatedareas must be washed with an effective cleaning com-pound followed by a potable water rinse before resumingfood operations.

• DO NOT make surface applications to mattresses orbedding. Mattress treatments must be confined to theseams, folds and edges only. Remove linens and washbefore reuse. Allow to dry before remaking bed.

Environmental Hazards

This pesticide is toxic to aquatic organisms, birds, andwildlife. DO NOT apply directly to water or to areas wheresurface water is present or intertidal areas below the meanhigh water mark.

Physical or Chemical Hazards

Contents under pressure. Keep away from heat, sparks,and open flame. DO NOT spray directly into any electricalequipment such as radios, televisions, computers, etc.(where there is exposed wiring or contact points) due topossibility of short circuits and shock hazard. DO NOTpuncture or incinerate container. Exposure to temperaturesabove 130°F may cause bursting. Spray may mar plastic,painted, or varnished surfaces. Test on a small surfaceprior to use.

Directions for UseIt is a violation of federal law to use this product in a man-ner inconsistent with its labeling.

FOR INTERIOR AND EXTERIOR APPLICATION AS ACRACK AND CREVICE OR SPOT TREATMENT

For Crack and Crevice use: Press down the spray tip torelease product while moving the spray can along lengthof treatment area. Apply at a rate of 2 sec/linear ft.

For Closed Void Treatment: Calculate the voids cubicarea and treat at a maximum rate of 3 sec/ft3.

USER SAFETY RECOMMENDATIONS

Users should:• Wash hands before eating, drinking, chewing gum,

using tobacco, or using the toilet.• Remove clothing/PPE immediately if pesticide gets

inside. Then wash thoroughly and put on cleanclothing.

• Remove PPE immediately after handling this product.Wash the outside of gloves before removing. As soonas possible, wash thoroughly and change into cleanclothing.

2

Spot Treatments: Hold can approximately 12" from sur-face to be treated and release product at a maximum rateof 11 sec/2 ft2. DO NOT exceed 2 ft2 for each spot treat-ment.

For indoor and exterior use as a crack and crevice or spottreatment only in the following areas to kill on direct spraycontact the listed pests in the following areas: houses,apartments, meat, fish, poultry and egg processing andpackaging plants, food/feed handling establishments (anarea or place other than a private residence in which foodis held, processed, prepared and/or served), and non-food/feed handling areas of food handling establishments(garbage rooms, lavatories, floor drains (to sewers), entriesand vestibules, offices, locker rooms, machine rooms, boil-er rooms, garages, mop closets and storage [after canningor bottling]), and commercial, institutional, warehousingestablishments, and zoos.

Apply as a spot and/or crack and crevice and/or voidtreatment where pests harbor, nest, trail, run, and/or breedor hide. Treat into voids or to surfaces beneath cabinets,furniture, spaces between equipment, expansion joints,surfaces behind sinks, floor drains (to sewers), lockers,and water pipes.

Exterior treatments around the listed areas are limited tospot and/or crack and crevice treatments where pestsenter around doors, windows, eaves, attic vents and holesin exterior walls where utilities enter.

To kill on direct spray contact drywood termites and sub-terranean termites in their above-ground galleries, work-ings or aerial nests within structures, locate existingopenings or drill pilot holes to access termite tunnels, gal-leries, infested cavities or voids. Apply as a void treatmentin holes to obtain thorough coverage of termites. Appli-cation of this product is not a substitute for a soil-appliedtermiticide. This product is not intended as a substitute formechanical alteration, soil treatment or foundation treat-ment. DO NOT use to treat soil directly, When activeinfestations exist, get a professional inspection.


DO NOT contaminate water, food, or feed by storage ordisposal.

Pesticide Storage:Store in a cool area, and never above 130°F, away fromheat, sparks, and open flame.

Pesticide Disposal:Waste resulting from use of this product may be dis-posed of on-site in accordance with the label directions,or at an approved waste disposal facility.

Container Disposal:

Nonrefillable container. DO NOT puncture or inciner-ate container. DO NOT reuse or refill this container.

Replace cap and discard empty container in trash, sani-tary landfill, or by other approved state and local pro-cedures. DO NOT puncture or incinerate. Offer forrecycling if available.

3

Prescription Treatment is a registered trademark ofWhitmire Micro-Gen Research Laboratories, Inc.

Phantom is a registered trademark of BASF Corporation.


007969-00285.20090209c1.NVA 2008-04-335-0206



Conditions of Sale and Warranty

The Directions For Use of this product reflect theopinion of experts based on field use and tests. Thedirections are believed to be reliable and must befollowed carefully. However, it is impossible to eliminateall risks inherently associated with the use of thisproduct. Crop injury, ineffectiveness or other unintendedconsequences may result because of such factors asweather conditions, presence of other materials, or useof the product in a manner inconsistent with its labeling,all of which are beyond the control of BASFCORPORATION (“BASF”) or the Seller. To the extentconsistent with applicable law, all such risks shall beassumed by the Buyer.

BASF warrants that this product conforms to thechemical description on the label and is reasonably fit forthe purposes referred to in the Directions For Use,subject to the inherent risks, referred to above.

TO THE EXTENT CONSISTENT WITH APPLICABLELAW, BASF MAKES NO OTHER EXPRESS ORIMPLIED WARRANTY OF FITNESS ORMERCHANTABILITY OR ANY OTHER EXPRESS ORIMPLIED WARRANTY.

TO THE EXTENT CONSISTENT WITH APPLICABLELAW, BUYER’S EXCLUSIVE REMEDY AND BASF’SEXCLUSIVE LIABILITY, WHETHER IN CONTRACT,TORT, NEGLIGENCE, STRICT LIABILITY, OROTHERWISE, SHALL BE LIMITED TO REPAYMENTOF THE PURCHASE PRICE OF THE PRODUCT.

TO THE EXTENT CONSISTENT WITH APPLICABLELAW, BASF AND THE SELLER DISCLAIM ANYLIABILITY FOR CONSEQUENTIAL, EXEMPLARY,SPECIAL OR INDIRECT DAMAGES RESULTINGFROM THE USE OR HANDLING OF THISPRODUCT.

BASF and the Seller offer this product, and the Buyerand User accept it, subject to the foregoing Conditionsof Sale and Warranty which may be varied only byagreement in writing signed by a duly authorizedrepresentative of BASF. 1108

4

FLYING INSECTS

When used according to label directions, 7.3 oz canwill dispense for 30 days.Kills: Flies, Mosquitoes, and Small Flying Moths.Kills mosquitoes, including the Culex species whichmay carry the West Nile Virus.

EPA Reg. No. 279-3388 EPA Est. No. 9444-LA-1

Active Ingredients:Pyrethrins........................................................ 0.975%

*Piperonyl Butoxide, technical ........................ 1.950%

N-octyl bicycloheptene dicarboximide ............ 3.050%

Inert Ingredients 94.025%

100.000%

*Equivalent to 1.56% (butylcarbityl) (6-propylpiperonyl) ether and 0.39% of relat-

ed compounds.

Contains Petroleum Distillates.

CONTAINS NO CFC's OR OTHER OZONE DEPLET-ING SUBSTANCES.FEDERAL REGULATIONS PROHIBIT CFC PROPEL-LANTS IN AEROSOLS


See Back Panel for Additional Precautionary Statements.

FMC Corporation

Agricultural Products Group

1735 Market Street

Philadelphia, PA 19103

Net Weight: 7.3 oz/207 g10-29-10R

PRECAUTIONARY STATEMENTSHazards to Humans & Domestic AnimalsCAUTIONContains petroleum distillate. Harmful if swallowed or absorbed through

the skin. Avoid breathing vapor or spray mist. Avoid contact with skin,

eyes or clothing. Prolonged or frequently repeated skin contact may

cause allergic reactions in some individuals. Wash hands thoroughly

with soap and water after handling and before eating, drinking, chewing

gum, using tobacco or using the toilet. Remove and wash contaminat-

ed clothing before reuse.

FIRST AIDIf Swallowed: Immediately call a poison control center or doctor. Do not

induce vomiting unless told to do so by a poison control center or doc-

tor. Do not give any liquid to the person. Do not give anything by mouth

to an unconscious person.

If Inhaled: Move person to fresh air. If person is not breathing, call 911

or an ambulance, then give artificial respiration, preferably by mouth-to-

mouth, if possible. Call a poison control center or doctor for further treat-

ment advice

If on Skin or Clothing: Take off contaminated clothing. Rinse skin

immediately with plenty of water for 15-20 minutes. Call a poison con-

trol center or doctor for treatment advice.

If In Eyes: Hold eye open and rinse slowly and gently with water for 15-

20 minutes. Remove contact lenses, if present, after the first 5 minutes,

then continue rinsing eye. Call a poison control center or doctor for

treatment advice.

HOT LINE NUMBER - Have the product container or label with you

when calling a poison control center or doctor, or going for treatment.

For additional information on this product (including health concerns,

medical emergencies or pesticide incidents), you may also contact 1-

(800)-331-3148.

NOTE TO PHYSICIAN - Contains petroleum distillate - vomiting may

cause aspiration pneumonia.

For Information Regarding the Use of this Product Call 1-800-321-1FMC (1362).

PHYSICAL OR CHEMICAL HAZARDSContents under pressure. Do not use or store near heat or open flame.

Do not puncture or incinerate container. Exposure to temperatures

above 130ºF may cause bursting. Do not allow spray to contact plastic,

painted or varnished surfaces.

ENVIRONMENTAL HAZARDSThis product is toxic to aquatic organisms, including fish and inverte-

brates. Do not contaminate water when disposing of equipment wash-

waters or rinsate. See Directions for Use for additional use restrictions

and precautions.

DIRECTIONS FOR USEIt is a violation of Federal law to use this product in a manner inconsis-

tent with its labeling.

Return to Index...

• Apply this product only as specified on this label

• Do not contaminate food or feedstuffs

• Do not use in aircraft cabins

• Do not enter or allow others to enter until vapors, mists and

aerosols have dispersed, and the area has been thoroughly ventilat-

ed

• Do not apply this product in a way that will contact workers or other

persons, either directly or through drift

• Do not remain in treated area. Exit immediately and remain outside

the treated area until aerosols, vapors and/or mists have dispersed

• Remove or cover exposed food and drinking water before applica-

tion

• Remove or cover dishes, utensils, food processing equipment and

food preparation surfaces, or wash them before use

• For indoor food handling/processing facilities: Do not make surface

spray applications when facility is in operation. During surface spray

applications, cover or remove exposed food. During space spray

applications, cover food processing surfaces or clean after treatment

with suitable detergent, rinse with potable water before use. Do not

apply more than 1 time per day.

• For metered release devices: Not for use in residential areas. Do

not use in nurseries or rooms where infants, ill or aged persons are

confined. Do not place metering device directly over or within 8 feet

of exposed food, dishes, utensils, food processing equipment and

food handling or preparation. Do not install within 3 feet of air vents.

Carefully follow directions for the dispenser unit and when replacing

cans or conducting maintenance.

• For agricultural premises and commercial animal housing: Do not

apply more than 1 time per day.

• When used in dairy barns or facilities: Close milk bulk tank lids to

prevent contamination from spray and from dead or falling insects.

Remove or cover milking utensils before application. Wash teats of

animals before milking.

• Remove pets, birds and cover fish aquariums before application.

FOR USE IN Food handling and food preparation areas of restaurants

and food processing plants, stores, farms, dairies, barns, kennels, fac-

tories, hotels, motels, offices, ships, planes (cargo area only), super-

markets food warehouses, bottling plants,, milk and egg handling areas

of dairies and chicken houses. Do not use in aircraft cabins.

This product contains a highly effective insecticide FOR USE INmetered release devices. The device activates the metered valve every

15 minutes. Usually the effectiveness of this product will be noticeable

within one hour after the device is activated. If less than 24 hour kill is

required, the device should [be set to] start one hour before kill is

desired and run one hour after kill is no longer needed. Keep in mind

that factors such as airflow rate, size of space treated, humidity and

room temperature affect insect activity and kill. Therefore, one unit per

6,000 cubic feet of unobstructed space should be considered as an

average with adjustments made depending on specific conditions at

usage site. As with any method of insecticide treatment, best results are

achieved when sanitation and other positive insect prevention practices

are followed, If used continuously, the container should be changed

once a month.

OUTDOORS: This product can be used to treat dog kennels, dog runs,

side yards, patios, decks and residential landscapes. Set the device to

treat at dawn and dusk when people and pets are not in the area. When

heavy pest infestations are present the device may be set to treat at 15-

45 minute intervals. Place devices out of the reach of children and pets.

Set device so spray drifts to area to be treated. Each device will treat up

to 650 sq ft. Use enough device to treat the entire area to be protected.

OPERATION: Remove protective cap from top of can and insert can in

device. Secure device and least 7 feet from floor or ground and at a

point where airflow or wind will carry the particles throughout the treat-

ment area.

STORAGE & DISPOSALDo not contaminate water, food or feed by storage or disposal.

Pesticide Storage: Do not store near heat or open flame. Keep this

product in its tightly closed original container when not in use. Store in

cool dry (preferable locked) area that is inaccessible to children and ani-

mals.

Pesticide Disposal: Do not puncture or incinerate. If empty: Place in

trash or offer for recycling if available. If partly filled: Call your local solid

waste agency for disposal instructions.

FOGGER

One Unit Treats up to 5,000 Cubic Feet

KILLS EXPOSED STAGES OF: Cockroaches, Fleas,Ticks, Houseflies, Mosquitoes, Small Flying Moths,Wasps, Crickets and Silverfish

FOR USE IN: Food and Non-Food Areas of Homes,Food Processing Plants, Restaurants, IndustrialBuildings, Schools, Warehouses, Offices, Theaters,Garages, Hotels, Motels, Hospitals and Kennels

FMC CorporationAgricultural Products Group1735 Market StreetPhiladelphia, PA 19103

Net Weight: 5 oz/142 g09-18-12

EPA Reg No. 279-3394 EPA Est. No. 9444-LA-1ACTIVE INGREDIENTS:

Pyrethrins ........................................................ 0.50%*Piperonyl Butoxide, technical ........................ 1.00%**N-Octyl Bicycloheptene Dicarboximide ........ 1.00%

OTHER INGREDIENTS ...................................... 97.50%100.00

*Equivalent to 0.80% of (butylcarbityl) (6-propylpiperonyl) ether and 0.20% relat-ed compounds.**MGK 264, Insecticide Synergist

CONTAINS NO CFC's OR OTHER OZONE DEPLET-ING SUBSTANCES. FEDERAL REGULATIONS PRO-HIBIT CFC PROPELLANTS IN AEROSOLS


See Back Panel for Additional Precautionary Statements.

PRECAUTIONARY STATEMENTSHazards to Humans & Domestic AnimalsCAUTIONHarmful if swallowed, inhaled or absorbed through the skin or eyes.Avoid breathing vapors or spray mist. Avoid contact with skin, eyes orclothing. Wash thoroughly with soap and water after use. Remove con-taminated clothing and wash before reuse. Remove pets, birds andcover fish aquariums before spraying.FIRST AIDIf Swallowed: Immediately call a poison control center or doctor. Do notinduce vomiting unless told to do so by a poison control center or doc-tor. Do not give any liquid to the person. Do not give anything by mouthto an unconscious person.If Inhaled: Move person to fresh air. If person is not breathing, call 911or an ambulance, then give artificial respiration, preferably by mouth-to-mouth, if possible. Call a poison control center or doctor for further treat-ment advice.If on Skin or Clothing: Take off contaminated clothing. Rinse skinimmediately with plenty of water for 15-20 minutes. Call a poison con-trol center or doctor for treatment advice.If In Eyes: Hold eye open and rinse slowly and gently with water for 15-20 minutes. Remove contact lenses, if present, after the first 5 minutes,then continue rinsing eye. Call a poison control center or doctor fortreatment advice.HOT LINE NUMBER - Have the product container or label with youwhen calling a poison control center or doctor, or going for treatment.For emergency information, call (800) 331-3148. For product informa-tion call (800) 321-1362, Monday-Friday, 8:00 am to 5:00 pm EST.PHYSICAL OR CHEMICAL HAZARDSContents under pressure. Keep away from heat, sparks and openflame. Do not puncture or incinerate container. Exposure to tempera-tures above 130°F may cause bursting. Do not apply this product in oron electrical equipment due to the possibility of a shock hazard. Thisproduct contains a highly flammable ingredient. It may cause a fire orexplosion if not used properly. Follow the "Directions for Use" on thislabel carefully.

Highly Flammable IngredientIngrediente Altamente Inflamable

DIRECTIONS FOR USEIt is a violation of Federal law to use this product in a manner inconsis-tent with its labeling.Shake Well Before Use. Cover exposed foods, dishes and food han-dling equipment. Open cabinets and doors to area to be treated. Shutoff fans and air conditioners. Put out all flames and pilot lights. Closedoors and windows. Point valve opening away from face and eyes whenreleasing. DO NOT use more than one fogger per room. DO NOT usein small enclosed spaces such as closets, cabinets or under counters ortables. Do not use in a room 5 ft. x 5 ft. or smaller; instead, allow fog toenter from other rooms. Turn off ALL ignition sources such as pilotlights (shut off gas valves), other open flames or running electricalappliances that cycle off and on (i.e. refrigerators, thermostats,etc.). Call your gas utility or management company if you need assis-tance with your pilot lights. Use one 9 oz. unit for each 9,000 cubic feetor one 5 oz. unit for 5,000 cubic feet of unobstructed space. Do notremain in the area during treatment, and ventilate thoroughly beforereentry.TO OPERATE VALVE: To lock valve in open position for automatic dis-charge, press valve button all the way down, hooking the catch. Thenplace fogger on stand or table in the center of the room with valvelocked open, placing several layers of newspaper or pad under fogger.Leave building at once and keep building closed for two hours beforeairing out. Open all doors and windows and allow to air for one-halfhour. Repeat spraying in two weeks or when necessary.To Kill Ticks and Fleas: Destroy pet's old bedding and replace. Usethis product as above. Pets should be treated with a registered tick andflea control product prior to reentry. Repeat as necessary to bring infes-tation under control.Do not apply while food processing is underway. Cover or remove all

Return to Index...

food processing surfaces. Thoroughly wash all food processing sur-faces before reuse. After spraying in bakeries, meat packing plants,food processing plants, etc., all benches, shelving, equipment, etc.where exposed food will be handled must be washed with an effectivecleaning compound followed by a potable water rinse prior to use. Inhospitals, remove patients prior to treatment. Ventilate area for twohours prior to returning patients.STORAGE & DISPOSALDo not contaminate water, food or feed by storage or disposal.Storage: Do not store near heat or open flame. Store in cool dry areaaway from children.Disposal: Do not Puncture or Incinerate! If empty: Place in trash oroffer for recycling if available. If partly filled: Call your local solid wasteagency for disposal instructions.

STEEL

Specimen Label

For Application by Trained Personnel Only

• Effective and fast-acting

• Provides flushing action and quick knockdown

• For indoor use as a ULV, space, area or contact spray



ACTIVE INGREDIENTS:Pyrethrins ........................................................................................3.00%*Piperonyl butoxide, Technical .........................................................6.00%**N-Octyl bicycloheptene dicarboximide ..........................................9.57%***OTHER INGREDIENTS ..............................................................81.43%

100.00%

* (butylcarbityl) (6-propylpiperonyl) ether related compounds.** MGK® 264, Insecticide Synergist*** Contains petroleum distillate

GENERAL: This concentrate is designed for use undiluted in mechanical sprayers that gives particles of aerosol size. It can be diluted with refined kerosenes, which meet Food Additive Regulation as defined by CFR Title 21, 172.884, and applied

in fogging equipment that give larger than aerosol particle size. It can also be diluted with the oil specified above and applied as a contact spray to kill crawling insects listed later on this label.

In Hospitals: Patients should be removed from room prior to treatment. Rooms should be ventilated for two hours after spraying. Do not return patients to room until after ventilation.

• Do not enter or allow others to enter until sprays have dried.

• Not for use in outdoor residential misting systems.

• Do not allow adults, children, or pets to enter the treated area for at least 15 minutes, until vapors, mists, and aerosols have dispersed, and the treated area has been thoroughly ventilated.

• Do not apply this product in a way that will contact workers or other persons, either directly or through drift.

• Only protected handlers may be in the area during application.

• Remove or cover exposed food and drinking water before application.

• Remove or cover dishes, utensils, food processing equipment, and food preparation surfaces, or wash them before use.

• Direct application to food contact surfaces is prohibited.

• Do not use in aircraft cabins.

• Do not apply more than 1 time per day.

• Do not remain in treated area. Exit area immediately and remain outside the treated area until aerosols, vapors and mists have dispersed.

• Avoid contamination of food or feedstuffs.

• Remove pets and birds and cover fish aquariums before spraying.

• When used in dairy barns or facilities: Close milk bulk tank lids to prevent contamination from spray and from dead or falling insects. Remove or cover milking utensils before application. Wash teats of animals before milking.

• Do not make space spray applications when facility is in operation.

• Prior to space spray applications, cover or remove food.

• Prior to space spray applications, cover food processing surfaces or clean after treatment and before use.

DIRECTIONS FOR USEIt is a violation of Federal law to use this product in a manner inconsistent with its labeling.

READ ALL DIRECTIONS COMPLETELY BEFORE USE

GENERAL PRECAUTIONS AND RESTRICTIONS

Return to Index...

INDOOR USE-UNDILUTEDULV AND SPACE SPRAY: Use in aerosol generators to kill exposed accessible stages of Flies (including Fruit Flies), Mosquitoes, Small Flying Moths, Fleas, Gnats, Wasps, Hornets, Clover Mites, Cheese Mites, Cheese Skippers, Boxelder Bugs, Earwigs, Ants, and the following common Stored Product Pests: Granary Weevils, Rice Weevils, Confused Flour Beetles, Saw-toothed Grain Beetles, Spider Beetles, Cigarette Beetles, Drugstore Beetles, Angoumois Grain Moths, Mediterranean Flour Moths, Indian Meal Moths, Tobacco Moths, Yellow Mealworms, Dark Mealworms, Grain Mites, Cadelles, and Red Flour Beetles.

Remove or cover exposed food and food handling surfaces. Close room and shut off all air conditioning or ventilating equipment. Apply at the rate of 1 fluid ounce undiluted concentrate per 1,000 cubic feet of space. Direct spray towards ceiling and upper corners of room. Leave room closed for 1/2 hour and ventilate thoroughly before re-entry. Do not apply this undiluted spray in residential areas or facilities operating under Federal Meat, Poultry, Shell Egg Grading and Egg Products Inspection Programs.

INDOOR AREAS for use in and around but not limited to [such as]:Animal Areas and Quarters

Animal Shelters

Animal Control Centers

Apartments

Arcades

Attics

Auditoriums

Bakeries

Beverage Plants

Bars

Basements

Bathrooms

Boats

Bottling Plants

Breweries

Brewery Warehouses

Buildings

Buses

Cabins

Cabinets

Cafeterias

Campers

Canneries

Churches

City Missions

Circus Tents

Closets

Club Houses

Commercial Buildings

Communication Centers

Condominiums

Concession Stands

Court Houses

Crawl Spaces

Crematoriums

Day Care Centers

Delicatessens

Department Stores

Diners

Dog Houses

Drugstores

Dumpsters

Dwellings

Egg Processing Plants

Factories

False Ceilings

Freight Containers

Fruit Packing Sheds

Funeral Parlors

Garbage Bins

Garbage Cans

Garbage Compactors

Garbage Trucks

Gas Stations

Grain Elevators

Grain Harvesting and Handling Equipment

Garages

Grain Mills

Granaries

Grocery Stores

Homes

Horse Stables and Barns

Horse Trailers

Hospices

Hospitals

Hotels

Indoor Eating Establishments

Industrial Installations

Institutional Dining Areas

Institutions

Jails

Kennels

Laboratories

Laundromats

Lavatories

Libraries

Liquor Stores

Locker Rooms

Marinas

Mausoleums

Meat Packing Plants

Mess Halls

Mini-Storages

Mobile Canteens

Mobile Homes

Morgues

Mortuaries

Motels

Movie Theaters

Museums

Nursing Homes

Office Buildings

Other Public Buildings

Parking Garages

Pool Halls

Prisons

Public Storage

Railroad Cars

Recreational Vehicles

Research Animal Quarters

Restaurants

Retail Stores

Rice Mills

Schools

Ships

Ship Holds

Smoke Shops

Sports Stadiums

Stables

Storage Bins (areas)

Stored Food in Multi-walled Paper or Cloth Bags

Stores

Supermarkets

Taverns

Textile Mills and Warehouses

Theaters

Tobacco Factories

Tobacco Warehouses

Tool Sheds

Trains

Transportation Equipment

Trucks

Truck Trailers

Tunnels

Utilities

Utility Rooms

Vending Machines

Veterinary Hospitals

Wall and Equipment Voids

Warehouses

Washrooms

Wholesale Stores

Wine Cellars

Wineries

Zoos

Almond Moths

Angoumois Grain Moths

Ants

Black Flies

Boxelder Bugs

Brown Dog Ticks

Cadelles

Carpet Beetles

Cereal Beetles

Cheese Mites

Cheese Skippers

Chocolate Moths

Cigarette Beetles

Clothes Moths

Clover Mites

Cockroaches

Coffee Bean Weevils

Confused Flour Beetles

Crickets

Dark Mealworms

Darkling Beetles

Deer Flies

Dermestid Beetles

Dried Fruit Beetles

Drugstore Beetles

Earwigs

Face Flies

Firebrats

Flat Grain Beetles

Fleas

Flies

Flying Moths

Fruit Flies

Fungus Gnats

Gnats

Grain Mites

Granary Weevils

Hide Beetles

Horn Flies

Hornets

Horseflies

Indian Meal Moths

Khapra Beetles

Lesser Grain Beetles

Lesser Grain Borers

Lesser House Flies

Mediterranean Flour Moths

Merchant Grain Beetles

Midges

Miller Moths

Millipedes

Mosquitoes

Palmetto Bugs

Pillbugs

Red Flour Beetles

Rice Flour Beetles

Rice Weevils

Rusty Grain Beetles

Saw-toothed Grain Beetles

Silverfish

Skipper Flies

Small Flying Moths

Spiders

Spider Beetles

Stable Flies

Sowbugs

Ticks

Ticks that may carry and transmit Lyme disease

Tobacco Moths

Warehouse Beetles

Wasps

Waterbugs

Yellow Jackets

Yellow Mealworms

For the control of insects, including:

CONTACT AND SPACE SPRAY: To kill Cockroaches, Silverfish, Earwigs, Ants and Spiders, use a mechanical aerosol generator or a fogger. Using no more than 2 fluid ounces per 1,000 square feet, direct the spray into all cracks and crevices, behind all equipment, cupboards, obstructions, dark harborage areas, walls, floors, underneath sinks, behind pipes and in all places that harbor insects to provide maximum penetration and impingement on the insects. Contact as many insects as possible. Do not allow spray to contact stored food. Then treat as a space spray. Apply at the rate of 1 fluid ounce per 1,000 cubic feet of space. Vacate treated area and leave the room closed for 1/2 hour. Ventilate thoroughly before re-entry. Do not apply this undiluted spray in residential areas or in facilities operating under Federal Meat, Poultry, Shell Egg Grading and Egg Products Inspection Programs.

NOTE: If there is a need to treat areas such as conduits, motor housings, junction and switch boxes, or other electrical equipment, turn off electrical equipment prior to application. After application, allow time for oil to dissipate before starting motors or placing switches in the “ON” position.

TREATMENT OF STORED FOOD AREAS: Foods in multi-walled bags, cloth bags or other packaging stored in such areas as listed areas to kill accessible adult stages of Almond Moths, Angoumois Grain Moths, Ants, Cadelles, Cereal Beetles, Cheese Mites, Cheese Skippers, Chocolate Moths, Cigarette Beetles, Cockroaches, Confused Flour Beetles, Crickets, Dark Mealworms, Drugstore Beetles, Earwigs, Firebrats, Flies, Fruit Flies, Fungus Gnats, Grain Mites, Granary Weevils, Hide Beetles, Indian Meal Moths, Mediterranean Flour Moths, Mosquitoes, Red Flour Beetles, Rice Weevils, Saw-toothed Grain Beetles, Silverfish, Small Flying Moths, Spiders, Spider Beetles, Yellow Mealworms, Dried Fruit Beetles, Warehouse Beetles, Rusty Grain Beetles, Lesser Grain Beetles, Coffee Bean Weevils, Khapra Beetles and other listed pests. Infested stored products should be destroyed, fumigated, or treated by other effective methods using an approved product intended for this purpose. As noted above, using no more than 2 fluid ounces per 1,000 square feet, disperse first by directing spray into cracks and crevices, corners, pallets and around stacks of packaged goods, hitting as many insects as possible, and then apply as a space spray at a dosage of 1/2 fluid ounce per 1,000 cubic feet of room space. Do not remain in treated area and ventilate before re-entry.

ON PEANUTS, NUTS, BEANS (INCLUDING COCOA), SEEDS, AND COPRA IN BAGS OR OTHER PACKAGING: To kill accessible stages of Almond Moths, Angoumois Grain Moths, Ants, Cadelles, Cereal Beetles, Cheese Mites, Cheese Skippers, Chocolate Moths, Cigarette Beetles, Cockroaches, Confused Flour Beetles, Crickets, Dark Mealworms, Drugstore Beetles, Earwigs, Firebrats, Flies, Fruit Flies, Fungus Gnats, Grain Mites, Granary Weevils, Hide Beetles, Indian Meal Moths, Mediterranean Flour Moths, Mosquitoes, Red Flour Beetles, Rice Weevils, Saw-toothed Grain Beetles, Silverfish, Small Flying Moths, Spiders, Spider Beetles, Yellow Mealworms, Dried Fruit Beetles, Warehouse Beetles, Rusty Grain Beetles, Lesser Grain Beetles, Coffee Bean Weevils, Khapra Beetles and other listed insects, using no more than 2 fluid ounces per 1,000 square feet, apply to the surface of stored or bagged products. Also spray walls, floors, other surfaces, and storage and handling areas thoroughly, being especially careful to treat cracks, crevices and similar hiding places. Then apply as a space spray at the rate of 1/2 fluid ounce per 1,000 cubic feet of space by directing the spray toward the ceiling and upper corners of the area and behind any obstructions.

Contact and Space Spray - Undiluted Spot Spray - To Kill Cockroaches: Using no more than 10 fluid ounces per 1,000 square feet in an appropriate ULV spraying device, inject the aerosol spray directly into cracks and crevices to completely fill wall, equipment, and other small structural void areas. Leave room ventilation or air conditioning equipment on during application.

INDOOR USE-DILUTEDSPACE SPRAY: For use in mechanical fogging, thermal fogging or spraying equipment to kill accessible stages of Almond Moths, Angoumois Grain Moths, Ants, Cadelles, Cereal Beetles, Cheese Mites, Cheese Skippers, Chocolate Moths, Cigarette Beetles, Cockroaches, Confused Flour Beetles, Crickets, Dark Mealworms, Drugstore Beetles, Earwigs, Firebrats, Flies, Fruit Flies, Fungus Gnats, Grain Mites, Granary Weevils, Hide Beetles, Indian Meal Moths, Mediterranean Flour Moths, Mosquitoes, Red Flour Beetles, Rice Weevils, Saw-toothed Grain Beetles, Silverfish, Small Flying Moths, Spiders, Spider Beetles, Yellow Mealworms, Dried Fruit Beetles, Warehouse Beetles, Rusty Grain Beetles, Lesser Grain Beetles, Coffee Bean Weevils, and Khapra Beetles. Remove or cover exposed food and cover food handling surfaces in edible product areas of food handling establishments. Close room and shut off all air conditioning or ventilating equipment. Dilute concentrate with a white mineral oil conforming to Regulation 21 CFR 121.2589(b) or an odorless light petroleum hydrocarbon conforming to 121.1182 at the rate of one part concentrate to two parts oil and mix well. Apply at the rate of 1 fluid ounce of concentrate per 1,000 cubic feet of space, filling the room with mist. Vacate treated area and ventilate before re-entry.

SURFACE SPRAY: To kill accessible stages of Ants, Drugstore Beetles, Earwigs, Cockroaches, Silverfish, Beetles, Boxelder Bugs, Clover Mites, Crickets, and other listed insects, dilute 2 fluid ounces of concentrate into 1 gallon of suitable diluent for maintenance, mix well, and apply as a coarse wetting spray using 1 gallon of spray mixture per 1,000 square feet of surface. To ensure maximum control of listed crawling insects, spray thoroughly into all cracks, molding, crevices, walls, floors, other surfaces, and storage and handling areas. Particular attention should be paid to areas where moisture collects such as drains, sinks, and water pipes, and around the base of heavy machinery and equipment, contacting as many insects as possible. Ants: Spray directly into nests, along trails, and directly on all ants

observed. Repeat as necessary.

FOR USE IN TRANSIT PROTECTION: To kill accessible stages of listed insects, clean and spray truck beds, boxcars, ship holds and other listed transit equipment before loading. Dilute 2 fluid ounces of concentrate into 1 gallon of suitable diluent. Thoroughly treat walls and floors. Spray each layer of cartons or containers lightly as stacked. Apply diluted spray at the rate of 1 gallon per 1,000 square feet. To kill Indian Meal Worms and Angoumois Grain Moths in stored grain, apply to the surface of binned grain at a rate of 1 gallon per 1,000 square feet. Apply at monthly intervals with the first appearance of moths and continuing until early fall. In case of severe infestation, break up webbing before spraying and make a second application in two weeks.

Contact Spray - Diluted for use with sprayers that give large, wetting spray particles to kill Cockroaches and Accessible Stages of Granary Insects: Cadelles, Confused Flour Beetles, Grain Mites, Granary Weevils, Meal Moth Larvae and Adults, Red Flour Beetles, Rice Weevils and Saw-toothed Grain Beetles. Cover or remove exposed food and close room as described above. Dilute concentrate with oil at the rate of 1 part concentrate plus 63 parts of oil or 2 fluid ounces per gallon and mix well. Spray outside walls of grain bins, flooring, about base of milling machinery, walls and baseboards, areas behind cabinets and around pipes, and other insect harborages using 1 gallon spray per 1,000 square feet of space. Force spray into all cracks and crevices.

DRIED FRUIT PRODUCTS in storage or being processed, to kill Confused Flour Beetles, Dried Fruit Beetles, Indian Meal Moths and Saw-toothed Grain Beetles: Remove and destroy infested products. Dilute concentrate with oil at the rate of 1 part concentrate plus 29 parts oil or 4.5 fluid ounces per gallon and mix well. Disperse 13 fluid ounces of this diluted product as a fine mist in the air above the trays and shelves. Do not apply to fruit directly. Use 1/2 fluid ounce per 1,000 cubic feet of space. Repeat application at this dosage in any given month. Leave the room closed for one hour. Do not remain in treated areas and ventilate the area before re-entry. Sweep up and destroy fallen insects.

STORED FOOD: (Stored in multi-wall bags or cloth bags) in flour mills, grain elevators, granaries, storage rooms, and warehouses to kill Angoumois Grain Moths, Cadelles, Cheese Mites, Cheese Weevils, Cigarette Beetles, Confused Flour Beetles, Dark Mealworms, Grain Mites, Granary Weevils, Indian Meal Moths, Mediterranean Flour Moths, Red Flour Beetles, Rice Weevils, Saw-toothed Grain Beetles and Yellow Mealworms: Remove and destroy infested products. Dilute concentrate with oil at the rate of 1 part concentrate plus 29 parts oil or 4.5 fluid ounces per gallon and mix well. Disperse this product first by directing no more than 60 fluid ounces of diluted spray per 1,000 square feet into corners, under pallets and around stacks of packaged foods, hitting as many insects as possible. Infested stored products should be fumigated or treated by other effective methods using an approved product intended for this purpose. Treat as a space spray using 6 fluid ounces of the diluted product. Use a dosage of two tenths (0.2) fluid ounce of concentrate per 1,000 cubic feet of space. Do not remain in treated areas and ventilate area before re-entry. This application will kill accessible, exposed stages of those stored product pests listed above. Sweep up and destroy fallen insects.

Zoos: As a space spray diluted for use in conventional mechanical fogging equipment to kill Flies, Gnats, Mosquitoes and Small Flying Moths: dilute 1 part concentrate plus 29 parts oil (refined kerosene) and mix well. Apply no more than 30 fluid ounces of diluted product per 1,000 cubic feet of space above the animals. Direct spray towards the upper portions of the enclosure, filling the room with mist. Keep area closed for at least 15 minutes. Vacate treated area and ventilate before reoccupying. Repeat treatment when reinfestation occurs.

FOR USE IN FEDERALLY INSPECTED MEAT AND POULTRY PLANTS: Dilute one part concentrate with 3 parts base oil (refined kerosene) and use with a ULV spraying device at the application rate of 3 fluid ounces of diluted product per 1,000 cubic feet of room space. Apply no more than 6 fluid ounces of the diluted spray into all cracks and crevices in woodwork, walls, floors, underneath sinks, behind pipes and in all places where these insects shelter. Contact as many insects as possible. Repeat as necessary to kill exposed or accessible stages of Ants, Earwigs, Flies, Fruit Flies, Gnats, Mosquitoes, Silverfish, Small Flying Moths, Spiders and Waterbugs. Before spraying, exposed food products and packaging materials must be covered or removed. After spraying, equipment and utensils must be washed with an effective cleaning compound and rinsed with potable water prior to use. Use as a space spray only when plant is not in operation.

NOTE: When using oil as the diluent, an odorless light petroleum hydrocarbon as defined by CFR Title 21, 172.884 should be used for all food area and food related applications. Additionally, when diluted and used according to label directions, this spray will meet specifications for use under Federal meat, poultry, and shell egg grading, and egg products inspection programs.


Manufactured by MGK®. ©2013 MGK. All rights reserved.


2.5M-1111

STORAGE AND DISPOSALDo not contaminate water, food, or feed by storage or disposal.

PESTICIDE STORAGE: Storage in a cool, dry area. Always store pesticides in the original container. Store away from food and pet food.

PESTICIDE DISPOSAL: To avoid wastes, use all material in this container by application according to label directions. If wastes cannot be avoided, offer remaining product to a waste disposal facility or pesticide disposal program (often such programs are run by state or local governments or by industry).

CONTAINER HANDLING: Nonrefillable container. Do not reuse or refill this container. Triple rinse container (or equivalent) promptly after emptying. Then offer for recycling if available, or puncture and dispose of in a sanitary landfill.

Triple Rinse as follows [for containers of 5 Gallons (18.9 L) or less]: Empty the remaining contents into application equipment or a mix tank and drain for 10 seconds after the flow begins to drip. Fill the container ¼ full with water and recap. Shake for 10 seconds. Pour rinsate into application equipment or a mix tank or store rinsate for later use or disposal. Drain for 10 seconds after the flow begins to drip. Repeat this procedure two more times.

PRECAUTIONARY STATEMENTSHAZARDS TO HUMANS AND DOMESTIC ANIMALS

CAUTIONHarmful if swallowed or absorbed through skin. Avoid contact with skin, eyes, or clothing. Prolonged or frequently repeated skin contact may cause allergic reactions in some individuals. Obtain medical attention if irritation persists. Avoid contamination of food or feedstuffs.

PERSONAL PROTECTIVE EQUIPMENT (PPE)Mixers, loaders, applicators, and other handlers must wear the following:• long-sleeved shirt• long pants• shoes and socks, and• chemical-resistant gloves made of barrier laminate, nitrile rubber, neoprene rubber

or viton.In addition to the above PPE, applicators using a high pressure handwand in an enclosed area must wear at least a NIOSH-approved respirator with:• a dust/mist filter with MSHA/NIOSH approval number prefix TC-21C, or• any N, R, P, or HE filter.In addition to the above PPE, applicators using handheld foggers in an enclosed area must wear a half-face, full-face, or hood-style NIOSH-approved respirator with:• a dust/mist filter cartridge (MSHA/NIOSH approval number prefix TC-21C), or• a canister approved for pesticides (MSHA/NIOSH approval number prefix TC-14G), or• a cartridge or canister with any R, P or HE filter.

USER SAFETY REQUIREMENTSFollow manufacturer’s instructions for cleaning/maintaining PPE. If no such instructions for washables exist, use detergent and hot water. Keep and wash PPE separately from other laundry.

Discard clothing and other absorbent material that have been drenched or heavily contaminated with the product’s concentrate. Do not reuse them.

USER SAFETY RECOMMENDATIONSUser should wash hands before eating, drinking, chewing gum, using tobacco, or using the toilet. User should remove clothing/PPE immediately if pesticide gets inside. Then wash thoroughly and put on clean clothing. User should remove PPE immediately after handling this product. Wash the outside of gloves before removing. As soon as possible, wash thoroughly and change into clean clothing.

ENVIRONMENTAL HAZARDSDo not discharge effluent containing this product into lakes, streams, ponds, estuaries, oceans or other waters unless in accordance with the requirements of a National Pollutant Discharge Elimination System (NPDES) permit and the permitting authority has been notified in writing prior to discharge. Do not discharge effluent containing this product to sewer systems without previously notifying the local sewage treatment plant authority. For guidance contact your State Water Board or Regional Office of the EPA.

PHYSICAL OR CHEMICAL HAZARDSCOMBUSTIBLE: Do not use or store near heat or open flame.

FIRST AIDIF SWALLOWED:• Immediately call a poison control center or doctor.• Do not induce vomiting unless told to do so by a poison control center or a doctor.• Do not give any liquid to the person.• Do not give anything by mouth to an unconscious person.

IF ON SKIN OR CLOTHING:• Take off contaminated clothing.• Rinse skin immediately with plenty of water for 15-20 minutes.• Call a poison control center or doctor for treatment advice.

NOTE TO PHYSICIAN: Contains petroleum distillate - vomiting may cause aspiration pneumonia.

Have the product container or label with you when calling a poison control center or doctor, or going for treatment. For additional information on this pesticide product (including health concerns, medical emergencies, or pesticide incidents), you may call 1-888-740-8712.

FIRST AIDIF SWALLOWED: CALL A PHYSICIAN OR POISON CONTROL CENTER IMMEDIATELY. If less than ten (10) minutes have passed since the poison was taken, give 1 or 2 glasses of water and induce vomiting by touching the back of the throat with finger. Repeat until vomit fluid is clear. Have patient lie down in a quiet, darkened room and keep him warm and quiet. If person is unconscious, do not give anything by mouth and do not induce vomiting. IF INHALED: Remove victim to fresh air. If not breathing, give artificial respiration. Get medical attention. IF IN EYES: Hold eyelids open and flush with steady, gentle stream of water for 15 minutes.

Get medical attention.IF ON SKIN: Wash with plenty of soap and water. Get medical attention.

NOTE TO PHYSICIANAdminister 100% OXYGEN by positive pressure to provide as much pulmonary gas exchange as possible, despite seizures. Administer ANTI-CONVULSANT DRUGS intravenously to control convulsions. NOTICE: It may be difficult or impossible to stop the seizure activity without stopping respiration. Be prepared to maintain pulmonary ventilation mechanically. Tracheotomy may be necessary if seizures are prolonged.

PO

ISO

NP

OIS

ON

KE

EP

OU

T O

F R

EA

CH

OF

CH

ILD

RE

ND

AN

GE

R

EPA

RE

G N

o. 5

042-

32

EPA

ES

T N

o. 6

7442

-OR

-002

NE

T C

ON

TEN

TS 1

6 oz

.M

anuf

actu

red

by: R

CO In

tern

atio

nal,

Inc.

• P.

O. B

ox 1

91, H

arris

burg

, Ore

gon

9744

6S

EE

INS

IDE

FO

R A

DD

ITIO

NA

L P

RE

CA

UT

ION

AR

Y S

TAT

EM

EN

TS

AC

TIV

E I

NG

RE

DIE

NT

:S

tryc

hnin

e A

lkal

oid

......

.....

.50%

INE

RT

ING

RE

DIE

NTS

....

99.5

0% T

OTA

L ...

......

......

......

.....

100.

00%

LIF

TH

ER

E

Return to Index....

PR

EC

AU

TIO

NA

RY

STA

TE

ME

NT

HA

ZAR

D to

HU

MA

NS

and

DO

ME

STI

C A

NIM

ALS

DANG

ER: C

onvu

lsiv

e po

ison

! Fat

al if

sw

allo

wed

or i

nhal

ed. H

arm

ful if

abs

orbe

d th

roug

h sk

in. D

o no

t get

in e

yes

or o

n cl

othi

ng.

Avo

id c

onta

ct w

ith s

kin.

Do

not b

reat

he d

ust.

Do

not a

pply

this

pro

duct

in a

way

that

will

con

tact

any

per

son

or p

et. W

ash

hand

s be

fore

ea

ting,

drin

king

, che

win

g gu

m, u

sing

toba

cco,

or u

sing

the

toile

t. R

emov

e co

ntam

inat

ed c

loth

ing

and

was

h cl

othi

ng b

efor

e re

use.

PE

RS

ON

AL

PR

OTE

CTI

VE

EQ

UIP

ME

NT

(PP

E)

App

licat

ors

and

othe

r ha

ndle

rs m

ust w

ear:

Lon

g-sl

eeve

d sh

irt a

nd lo

ng p

ants

, cot

ton

glov

es, a

nd s

hoes

plu

s so

cks.

Kee

p an

d w

ash

PP

E s

epar

atel

y fr

om o

ther

laun

dry.

US

ER

SA

FETY

RE

CO

MM

EN

DA

TIO

NS

Use

rs s

houl

d re

mov

e cl

othi

ng im

med

iate

ly if

pes

ticid

e ge

ts in

side

. T

hen,

was

h th

orou

ghly

and

put

on

clea

n cl

othi

ng.

Use

rs s

houl

d re

mov

e P

PE

imm

edia

tely

afte

r ha

ndlin

g th

is p

rodu

ct.

As

soon

as

poss

ible

, was

h th

orou

ghly

and

cha

nge

into

cle

an c

loth

ing.

EN

VIR

ON

ME

NTA

L H

AZA

RD

STh

is p

rodu

ct is

toxi

c to

fish

, bird

s, a

nd o

ther

wild

life.

Do

not a

llow

bai

t to

be e

xpos

ed o

n so

il su

rface

. Do

not a

pply

dire

ctly

to w

ater

, or

to a

reas

whe

re s

urfa

ce

wat

er is

pre

sent

, or

to in

terti

dal a

reas

bel

ow th

e m

ean

high

wat

er m

ark.

Do

not c

onta

min

ate

wat

er b

y th

e cl

eani

ng o

f equ

ipm

ent o

r di

spos

al o

f was

tes.

Do

not

appl

y di

rect

ly to

food

or f

eed

crop

s.

EN

DA

NG

ER

ED

SP

EC

IES

CO

NS

IDE

RA

TIO

NS

NO

TIC

E: T

he k

illin

g of

a m

embe

r of a

n en

dang

ered

spe

cies

dur

ing

stry

chni

ne b

aitin

g op

erat

ions

may

resu

lt in

a fi

ne u

nder

the

End

ange

red

Spe

cies

Act

. Bef

ore

baiti

ng, t

he u

ser i

s ad

vise

d to

con

tact

the

Reg

iona

l U.S

. Fis

h an

d W

ildlif

e S

ervi

ce (E

ndan

gere

d S

peci

es S

peci

alis

t) or

the

loca

l Fis

h an

d G

ame

Offi

ce fo

r spe

cific

in

form

atio

n on

end

ange

red

spec

ies.

Stry

chni

ne b

aits

sho

uld

not b

e us

ed in

the

geog

raph

ic ra

nges

of t

he fo

llow

ing

spec

ies

exce

pt u

nder

pro

gram

s an

d pr

oced

ures

ap

prov

ed b

y th

e U

SE

PA: C

alifo

rnia

con

dor,

San

Joa

quin

kit

fox,

Mor

row

Bay

kan

garo

o ra

t, gr

ay w

olf a

nd g

rizzl

y be

ar.

STO

RA

GE

AN

D D

ISP

OS

AL

Do

not c

onta

min

ate

wat

er, f

ood,

or f

eed

by s

tora

ge o

r dis

posa

l.

PE

STI

CID

E S

TOR

AG

E:

Sto

re o

nly

in o

rigin

al c

onta

iner

, in

a dr

y pl

ace

inac

cess

ible

to c

hild

ren,

pet

s an

d do

mes

tic a

nim

als.

PE

STI

CID

E D

ISP

OS

AL:

Rec

over

any

spi

lled

prod

uct.

Sec

urel

y w

rap

in s

ever

al la

yers

of n

ewsp

aper

, and

dis

card

in tr

ash.

CO

NTA

INE

R D

ISP

OS

AL:

Sec

urel

y w

rap

orig

inal

con

tain

er in

sev

eral

laye

rs o

f new

spap

er a

nd d

isca

rd in

tras

h.

DIR

EC

TIO

NS

FO

R U

SE

It is

a v

iola

tion

of F

eder

al la

w to

use

this

pro

duct

in a

man

ner i

ncon

sist

ent w

ith it

s la

belin

g.

USE

RES

TRIC

TIO

NS:

Thi

s pr

oduc

t may

be

used

onl

y in

man

ual,

subt

erra

nean

app

licat

ions

in te

rres

trial

food

cro

ps, a

nd te

rres

trial

non

food

and

fore

stry

ar

eas

to c

ontro

l the

follo

win

g sp

ecie

s of

poc

ket g

ophe

rs:

Nor

ther

n (T

hom

omys

talp

oide

s); S

outh

ern

(Tho

mom

ys u

mbr

inus

); C

amas

(Tho

mom

ys b

ulbi

voru

s); V

alle

y (T

hom

omys

bot

tae)

; Maz

ama

(Tho

mom

ys m

azam

a); P

lain

s (G

eom

ys b

ursa

rius)

; Mou

ntai

n (T

hom

omys

mon

ticol

a); a

nd T

owns

end’

s po

cket

gop

hers

(Tho

mom

ys

tow

nsen

dii).

Bai

t mus

t be

depo

site

d in

poc

ket g

ophe

rs’ u

nder

grou

nd ru

nway

s. D

o no

t app

ly b

ait a

bove

gro

und.

Do

not a

pply

this

pro

duct

by

mea

ns o

f a b

urro

w-b

uild

er m

achi

ne.

Do

not a

pply

this

pro

duct

ove

r fo

od o

r fe

ed c

rops

. Do

not e

xpos

e ba

its in

a m

anne

r w

hich

pre

sent

s a

haza

rd to

hum

ans,

pet

s, p

oultr

y, o

r liv

esto

ck. K

eep

pets

, do

mes

tic a

nim

als,

and

peo

ple

not i

nvol

ved

with

the

appl

icat

ion

out o

f the

trea

tmen

t are

a w

hile

pro

duct

is b

eing

app

lied.

BAIT

ING:

Bur

row

ing

pock

et g

ophe

rs th

row

out

low,

fan-

shap

ed d

irt m

ound

s on

eith

er s

ide

of th

eir

unde

rgro

und

runw

ays.

Sho

rt la

tera

l tun

nels

con

nect

the

mou

nds

to th

e m

ain

runw

ay. E

xcep

t whe

n a

pock

et g

ophe

r is

thro

win

g ou

t dirt

, its

late

ral t

unne

ls a

re p

lugg

ed w

ith s

oil a

t the

mou

nd, o

ften

crea

ting

a ho

rses

hoe-

shap

ed d

epre

ssio

n. P

ocke

t gop

hers

may

be

cont

rolle

d by

pla

cing

bai

t in

the

mai

n ru

nway

, afte

r gai

ning

acc

ess

by re

mov

ing

plug

s in

late

ral t

unne

ls o

r by

prob

ing

soil

to lo

cate

th

e m

ain

runw

ay.

LATE

RAL

TUNN

ELS:

With

a lo

ng-h

andl

ed s

poon

or o

ther

sui

tabl

e to

ol, c

aref

ully

rem

ove

dirt

plug

. Ins

ert a

teas

poon

ful o

f bai

t at t

he ju

nctio

n of

the

late

ral t

unne

l and

the

mai

n ru

nway

. Re-

clos

e ho

le, t

akin

g ca

re to

exc

lude

ligh

t and

not

to a

llow

soi

l to

cove

r bai

t. Pi

ck u

p an

d pr

oper

ly d

ispo

se o

f any

spi

lled

bait.

PROB

ING:

With

a m

etal

rod

or o

ther

sui

tabl

e im

plem

ent,

prob

e so

il 6

to 8

inch

es a

roun

d m

ound

, sta

rting

from

plu

g si

de, t

o lo

cate

mai

n ru

nway

. Whe

n ru

nway

is e

nter

ed,

resi

stan

ce o

n pr

obe

will

dec

reas

e ab

rupt

ly. R

emov

e pr

obe

and

inse

rt a

teas

poon

ful o

f bai

t thr

ough

pro

be h

ole

(enl

arge

d if

nece

ssar

y). C

over

ope

ning

with

a ro

ck, a

clu

mp

of s

oil,

or o

ther

obj

ect t

hat w

ill e

xclu

de li

ght.

Take

car

e no

t to

perm

it di

rt to

cov

er b

ait.

Pick

up

and

prop

erly

dis

pose

of a

ny s

pille

d ba

it.

APPL

ICAT

ION

RATE

: Mak

e tw

o to

five

set

s pe

r bur

row

sys

tem

, dep

endi

ng u

pon

its a

ppar

ent s

ize. D

epen

ding

upo

n po

cket

gop

her d

ensi

ty, o

ne p

ound

of b

ait w

ill tr

eat o

ne

to e

ight

acr

es.

NO

TIC

E: B

ecau

se R

CO

Inc.

has

no

cont

rol o

ver

stor

age,

han

dlin

g an

d co

nditi

ons

of u

se, w

hich

are

of c

ritic

al im

port

ance

, RC

O In

c. m

akes

no

repr

e-se

ntat

ion

of w

arra

nty,

eith

er e

xpre

ssed

or i

mpl

ied,

for r

esul

ts d

ue to

mis

use,

impr

oper

han

dlin

g or

sto

rage

of t

his

mat

eria

l. N

or d

oes

RC

O In

c. a

ssum

e an

y re

spon

sibi

lity

for

inju

ry to

per

sons

, cro

ps, a

nim

als,

soi

l or

prop

erty

aris

ing

out o

f mis

use,

impr

oper

han

dlin

g or

sto

rage

of t

his

mat

eria

l.

PO

ISO

N

PO

ISO

N

KE

EP

OU

T O

F R

EA

CH

OF

CH

ILD

RE

ND

AN

GE

RO

ME

GA

GO

PH

ER

GR

AIN

BA

IT

EPA

RE

G N

o. 5

042-

32E

PA E

ST

No.

674

42-O

R-0

02M

anuf

actu

red

by: R

CO In

tern

atio

nal,

Inc.

P.O.

Box

191

, Har

risbu

rg, O

rego

n 97

446

NE

T C

ON

TEN

TS 1

6 oz

.

AC

TIV

E I

NG

RE

DIE

NT

:S

tryc

hnin

e A

lkal

oid

......

.....

.50%

INE

RT

ING

RE

DIE

NTS

....

99.5

0% T

OTA

L ...

......

......

......

.....

100.

00%

FIRST AIDIf on skin orclothing

• Take off contaminated clothing.• Rinse skin immediately with plenty of water for 15-

20 minutes.• Call a poison control center or doctor for treatment

advice.

Page 1

Net Contents: 25 lbs

For use to control Ants (including Imported FireAnts), Mole Crickets and other Insect pests on lawnsin landscaped areas and perimeters around residen-tial, institutional, public, commercial and industrialbuildings, parks, recreational areas and athleticfields.

EPA Reg. No. 279-3168 EPA Est. 279-IL-1

Active Ingredient: By Wt.Bifenthrin*..............................................................0.2%

Other Ingredients ............................................... 99.8%100.0%

*Cis isomers 97% minimum, trans isomers 3% maximum.


CAUTION

FMC CorporationAgricultural Products Group1735 Market StreetPhiladelphia PA 1910306-30-11

PRECAUTIONARY STATEMENTSHazards to Humans (and Domestic Animals)CautionHarmful if absorbed through skin. Avoid contact with skin, eyes or clothing. Environmental HazardsThis pesticide is extremely toxic to fish and aquatic invertebrates. Do notapply when weather conditions favor drift from treated areas. Drift andrun-off from treated areas may be hazardous to aquatic organisms inneighboring areas.To protect the environment, do not allow pesticide to enter or run off intostorm drains, drainage ditches, gutters or surface waters. Applying thisproduct in calm weather when rain is not predicted for the next 24 hourswill help to ensure that wind or rain does not blow or wash pesticide offthe treatment area. Sweeping any product that lands on a driveway,sidewalk, or street, back onto the treated area of the lawn or garden willhelp to prevent run off to water bodies or drainage systems.

DIRECTIONS FOR USEIt is a violation of Federal Law to use this product in a manner inconsis-tent with its labeling. Not for use on plants being grown for sale of othercommercial use, or for commercial seed production, or for research pur-poses. For use on plants intended for aesthetic purposes or climatemodification and being grown in interior plantscapes, ornamental gar-dens or parks, or lawns or grounds.Do not apply more than 0.2 lb. active ingredient (a.i.) per acre per appli-cation on residential use sites (i.e., around private homes, apartmentbuildings, condominiums, non-agricultural outbuildings, non-commer-cial greenhouses, pre-schools or day care facilities). May be applied atup to 0.4 lb. a.i. per acre per application on non-residential use sites(i.e., around institutional, public, commercial or industrial buildings;parks; recreational areas or athletic fields).Do not broadcast apply more than 0.4 lbs. A.I. (200 lbs. Talstar PLGranular) per Acre per year.Apply this product directly to the lawn or garden area. Water treatedarea as directed on this label. Do not water to the point of run-off.

See other panels for additional precautionary information.orSee back panel pamphlet for additional precautionary informationand complete directions for use.

Have the product container or label with you when calling a poisoncontrol center or doctor, or going for treatment. You may also contact1-(800)-331-3148 for Emergency Assistance.

NOTE TO PHYSICIAN

For Information Regarding the Use of this Product Call 1-800-321-1FMC (1362).

This product is a pyrethroid. If large amounts have been ingested,milk, cream and other digestible fats and oils may increase absorp-tion and so should be avoided.

HOTLINE NUMBER

Return to Index...

LAWN AND PERIMETER APPLICATIONSLawn Application: Broadcast Talstar® PL granular insecticide withsuitable application equipment to ensure uniform coverage over thetreatment area.

APPLICATION RATES

Armyworms1

Cutworms1

Sod Webworm1

Annual Bluegrass Weevil(Hyperodes) (Adult)2

Billbugs (Adult)3

Black Turfgrass Ataenius(Adult)4

LeafhoppersMealybugs

AntsCentipedesChinch Bugs5

European Crane Flies(larvae)6

Fleas (Larvae)7

Fleas (Adult)Imported Fire Ants(Adult)8

Imported Fire Ants(Mounds)8

MillipedesMole Cricket (Adult)9

Mole Cricket (Nymph)10

PillbugsScorpions11

SowbugsTicks12

0.1lbs. AI/A

0.1 - 0.2lbs. AI/A

0.2 - 0.4lbs. AI/A

50 lbs.per acre

50 - 100 lbs.per acre

100 - 200 lbs.per acre

1.15 lbs.per 1000 sq. ft.

1.15 - 2.3 lbs.per 1000 sq. ft.

2.3 - 4.6 lbs.per 1000 sq. ft.

Pest Active ingredientlbs. per acre

Application RateTalstar PL

The application rates listed in the following table will provide excellent con-trol of the respective pests under typical conditions. However, at the dis-cretion of the applicator, Talstar PL may be applied at up to 0.4 lb AI/A tocontrol each of the pests listed in this Table. However, for residential lawnuse, do not apply more than 0.2 lbs. A.I. per Acre per application.

Comments1Armyworms, Cutworms, and Sod Webworms: To ensure optimum control, irri-gate the treated area with up to 0.1 inches of water immediately after applicationto activate (release from the granule) the insecticide.2Annual Bluegrass Weevil (Hyperodes) adults: Applications should be timed tocontrol adult weevils as they leave their overwintering sites and move into grassareas. This movement generally begins when Forsythia is in full bloom and con-

cludes when flowering dogwood is in full bloom. Consult your State CooperativeExtension Service for more specific information regarding application timing.3Billbug adults: Applications should be made when adult billbugs are firstobserved during April and May. Degree day models have been developed to opti-mize application timing. Consult your State Cooperative Extension Service forinformation specific to your region. In temperate regions, spring applications tar-geting billbug adults will also provide control of over-wintered chinch bugs.4Black Turfgrass Ataenius adults: Applications should be made during May andJuly to control the first and second generation of black turfgrass ataenius adults,respectively. The May application should be timed to coincide with the full bloomstage of Vanhoutte spiraea (Spiraea vanhouttei) and horse chestnut (Aesculushippocastanum). The July application should be timed to coincide with the bloom-ing of Rose of Sharon (Hibiscus syriacus).5Chinch Bugs: Chinch bugs infest the base of grass plants and are often found inthe thatch layer. Irrigate the treated area with up to 0.25 inches of water immedi-ately after application to activate (release from the granule) the insecticide. Chinchbugs can be one of the most difficult pests to control in grasses and the higherapplications rates may be required to control populations that contain bothnymphs and adults during the summer.6European Crane Flies: Treatments should be made to control early to mid-sea-son larvae (approximately August – February) as they feed on plant crowns.Treatments made to late-season larvae (approximately March - April) may onlyprovide suppression. Consult your local extensions agent for specific recommen-dations for your area.7Flea larvae: Flea larvae develop in the soil of shaded areas that are accessibleto pets or other animals. Irrigate the treated area with up to 0.5 inches of waterimmediately after application to activate (release from the granule) the insecticide.8Imported Fire ants: Control will be optimized by combining broadcast applica-tions that will control foraging workers and newly mated fly-in queens with moundtreatments that will control existing colonies. If the soil is not moist, then it is impor-tant to irrigate before application. Broadcast treatments should apply 0.2 to 0.4 lbAI/A. Mounds should be treated by applying !" cup of Talstar PL Granular permound and then drenching the mound with 1 to 2 gallons of water. The moundsshould be treated with sufficient force to break their apex and allow the insecticidesolution to flow into the ant tunnels. Treat three feet out around the mound. Forbest results, apply in cool weather (65 - 80˚ F) or in early morning or late eveninghours.9Mole Cricket adults: Achieving acceptable control of adult mole crickets is diffi-cult because preferred grass areas are subject to continuous invasion during theearly spring by this extremely active stage. Applications should be made as late inthe day as possible and should be watered in with up to 0.5 inches of water imme-diately after treatment. If the soil is not moist, then it is important to irrigate beforeapplication to bring the mole crickets closer to the soil surface where contact withthe insecticide will be maximized. Grass areas that receive pressure from adultmole crickets should be treated at peak egg hatch to ensure optimum control ofsubsequent nymph populations (see below).10Mole Cricket nymphs: Grass areas that received intense adult mole cricketpressure in the spring should be treated immediately prior to peak egg hatch.Optimal control is achieved at this time because young nymphs are more suscep-tible to insecticides and they are located near the soil surface where the insecti-cide is most concentrated. Control of larger, more damaging, nymphs later in theyear may require both higher application rates and more frequent applications tomaintain acceptable control. Applications should be made as late in the day aspossible and should be watered in with up to 0.5 inches of water immediately aftertreatment. If the soil is not moist, then it is important to irrigate before applicationto bring the mole crickets closer to the soil surface where contact with the insecti-cide will be maximized.11Scorpions: To ensure optimum control, treat the building perimeter at dusk toprevent outdoor scorpions from entering the building. Scorpions reside hidden incracks and voids during the day and are active at night at temperatures above77ºF/25ºC. Resting areas can be identified at night using a blacklight (UV bulb) asscorpions will fluoresce. These areas should also be treated. Prior to treatment, toincrease treatment efficacy, remove trash, debris, or firewood that scorpions mayuse as resting sites.12Ticks (Including ticks that may transmit Lyme Disease and RockyMountain Spotted fever): Do not make spot applications. Treat the entire areawhere exposure to ticks may occur. Use higher application rates when treatingareas with dense ground cover or heavy leaf litter. Ticks may be reintroduced fromsurrounding areas on host animals. Do not allow public use of treated areas dur-ing application.Deer ticks (Ixodes sp.) have a complicated life cycle that ranges over a two yearperiod and involves four life stages. Applications should be made in mid to late-spring to control larvae and nymphs that reside in the soil and leaf litter.American dog ticks may be a considerable nuisance in suburban settings, par-ticularly where homes are built on land that was previously field or forest. Theseticks commonly congregate along paths or roadways where humans are likely tobe encountered. Applications should be made as necessary from mid-spring toearly fall to control American dog tick larvae, nymphs and adults.

In New York State, this product may NOT be applied to any grassor turf area within 100 feet of a water body (lake, pond, river,stream, wetland, or drainage ditch).In New York State, do make a single repeat application of TalstarPL Granular if there are signs of renewed insect activity, but notsooner than two weeks after the first application.

STORAGE AND DISPOSALProhibitionsDo not contaminate water, food or feed by storage or disposal.Pesticide StorageKeep out of reach of children and animals. Store in original contain-ers only. Store in a cool, dry place and avoid excess heat. Carefullyopen containers. After partial use close tightly.In case of spill, avoid contact, isolate area and keep out animals andunprotected persons. Confine spil ls. Call CHEMTREC(Transportation and spills): (800) 424-9300.To confine spill: Cover to prevent dispersal. Place damaged packagein a holding container. Identify contents.Pesticide DisposalWastes resulting from the use of this product may be disposed of onsite or at an approved waste disposal facility.Container DisposalPaper and plastic bags: Non-refillable. Do not reuse or refill thiscontainer. Completely empty bag into application equipment. Thenoffer for recycling, if available, or dispose of empty bag in a sanitarylandfill or by incineration, or, by burning. Do not burn unless allowedby state or local authorities. If burned, stay out of smoke.

Do not make applications during rain.Not for use on golf courses, sod farms, nurseries, in commercial green-houses or on grass grown for seed.

INDUSTRIAL NON-AGRICULTURAL APPLICATIONS (Including Industrial Sites, Parks, Ball Fields andCemeteries)Broadcast Spot Applications: For the control of actively foraging ants(including Imported Fire Ants) broadcast uniformly 2.3 to 4.6 lbs. TalstarPL granular insecticide per 1000 sq. ft. (0.2 to 0.4 lbs. a.i./Acre). Seecomments section under Lawn Applications for additional rate recom-mendations.Pad Mounted Electrical Sites: To reduce or prevent ant mound build-ing activity on electrical pads, uniformly distribute 1.0 to 1.5Tablespoons (0.06 to 0.09 lbs.) of Talstar PL granular insecticide per 4sq. ft. of mounting pad. Where existing transformers are completely orpartially filled with soil excavated by resident ants, remove any excessfill and level the remaining soil prior to application. Food utensils suchas tablespoons must not be used for food purposes after use inmeasuring pesticides.Note: Electrical transformers appear to be more attractive to ants dur-ing the cooler months. For best results treat in the Fall or early Spring.

Perimeter Application: Apply to ground area 5 to 10 feet wide around andadjacent to the structure.

Applic. Rate:Pounds Per Band1,000 sq. ft. Width 100 150 200 250 300 400 500 1,000

2.3 5 feet 1.3 1.9 2.5 3.0 3.6 4.8 5.9 11.72.3 10 feet 3.0 4.2 5.3 6.5 7.6 9.9 12.2 23.7

3.0 5 feet 1.7 2.5 3.3 3.9 4.7 6.3 7.7 15.23.0 10 feet 3.9 5.4 6.9 8.5 9.9 12.9 15.9 30.9

3.5 5 feet 2.0 2.9 3.8 4.5 5.4 7.2 8.9 17.53.5 10 feet 4.5 6.3 8.0 9.8 11.4 14.9 18.3 35.5

4.6 5 feet 2.6 3.8 5.0 6.0 7.2 9.6 11.8 23.44.6 10 feet 6.0 8.4 10.6 13.0 15.2 19.8 24.4 47.4

Note: The amounts of Talstar PL Granular listed in the above table are based onthe total area being treated. This area is determined by multiplying the linear dis-tance by the band width and then adding to that value the area of a circle whoseradius is equal to the band width (to account for the area treated at the four cor-ners of a rectangular structure).

Pounds of Talstar PL Granular for Perimeter ApplicationsLinear Distance (Feet) Around Structure

Resistance: Some insects are known to develop resistance to productsused repeatedly for control. Because the development of resistancecannot be predicted, the use of this product should conform to resis-tance management strategies established for the use area. Consultyour local or state pest management authorities for details.If resistance to this product develops in your area, this product, or otherproducts with a similar mode of action, may not provide adequate con-

Fire ant mound treatment: Apply 1/2 cup of Talstar® PL GranularInsecticide per mound and then drench the mound with 1 to 2 gallons ofwater. The mound should be drenched with sufficient force to break itsapex and allow the insecticide to flow into the ant tunnels. Treat threefeet out around the mound.For best results, apply in cool weather (65 to80˚F) or in early morning or late evening hours. Treat new mounds asthey appear. Food utensils such as teaspoons and measuring cupsshould not be used for food purposes after use with insecticide

Boundary Applications: Apply to soil areas, ornamental gardens, pave-ment crevices, fencelines, planter areas, vegetation areas and mulch areas

Conditions of Sale and Limitation of Warranty and Liability:NOTICE: Read the entire Directions for Use and Conditions of Saleand Limitation of Warranty and Liability before buying or using thisproduct. If the terms are not acceptable, return the product at once,unopened, and the purchase price will be refunded.

The Directions for Use of this product must be followed carefully. It isimpossible to eliminate all risks inherently associated with the use of thisproduct. Crop injury, ineffectiveness, or other unintended conse-quences may result because of such factors as manner of use or appli-cation, weather or crop conditions beyond the control of FMC or Seller.All such risks shall be assumed by Buyer and User, and Buyer and Useragree to hold FMC and Seller harmless for any claims relating to suchfactors.Seller warrants that this product conforms to the chemicaldescription on the label and is reasonably fit for the purposesstated on the Directions for Use when used in accordance with thedirections under normal conditions of use. TO THE EXTENT CON-SISTENT WITH APPLICABLE LAW, FMC MAKES NO WARRANTIESOF MERCHANTABILITY OR OF FITNESS FOR A PARTICULARPURPOSE, NOR ANY OTHER EXPRESS OR IMPLIED WAR-RANTIES WITH RESPECT TO THE SELECTION, PURCHASE, ORUSE OF THIS PRODUCT. Any warranties, express or implied, hav-ing been made are inapplicable if this product has been used con-trary to label instructions, or under abnormal conditions, or underconditions not reasonably foreseeable to (or beyond the control of)seller or FMC, and buyer assumes the risk of any such use.To the extent consistent with applicable law, FMC or seller shall not beliable for any incidental, consequential or special damages resultingfrom the use or handling of this product. TO THE EXTENT CONSIS-TENT WITH APPLICABLE LAW, THE EXCLUSIVE REMEDY OF THEUSER OR BUYER, AND THE EXCLUSIVE LIABILITY OF FMC ANDSELLER FOR ANY AND ALL CLAIMS, LOSSES, INJURIES OR DAM-AGES (INCLUDING CLAIMS BASED ON BREACH OF WARRANTY,CONTRACT, NEGLIGENCE, TORT, STRICT LIABILITY OR OTHER-WISE) RESULTING FROM THE USE OR HANDLING OF THIS PROD-UCT, SHALL BE THE RETURN OF THE PURCHASE PRICE OF THEPRODUCT OR, AT THE ELECTION OF FMC OR SELLER, THEREPLACEMENT OF THE PRODUCT.This Conditions of Sale and Limitation of Warranty and Liability may notbe amended by any oral or written agreement.

Talstar and FMC - FMC TrademarksTalstar PL Spreader Setting Guide

Lesco® Broadcast - New

Lesco® Broadcast - Old

Scotts® HandyGreen® II

Scotts® SpeedyGreen® 2000

Scotts® Standard Broadcast

Gandy® M

odels 42, 36, 30, 24"

Spyker® All Models (Push)

Application Ratelbs/1,000 sq.ft.

5

C + 1/2

10

B + 1/4A + 1/2 2

3 1/4

10

2*

--

--

3**

--

**

1612

--

10.5

3.12.62

5

10

3

----

7

--9--

1010

1.15 lbs2.3 lbs4.6 lbsPattern SettingWidth Ft.

Ground Speed at ~3.1 mph for all settings*2 is the lowest setting for this model**This model does not have settings fine enough for this application

trol. If poor performance cannot be attributed to improper application orextreme weather conditions, a resistant strain of insect may be present.If you experience difficulty with control and suspect that resistance is areasonable cause, immediately consult your local company representa-tive or pest management advisor for the best alternative method of con-trol for your area.

ACTIVE INGREDIENT:fipronil: 5-amino-1-(2,6-dichloro-4-(trifluoromethyl)phenyl)-4-((1,R,S)-(trifluoromethyl)sulfinyl)-1-H-pyrazole-3-carbonitrile . . . . . . . . . . . . . . . . . . . . . . . . . 9.1%

OTHER INGREDIENTS: . . . . . . . . . . . . . . . . . . . . . . . . . 90.9%TOTAL: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100.0%One gallon of Termidor® SC termiticide/insecticide contains0.8 lb of fipronil.


KEEP OUT OF REACH OF CHILDREN.CAUTION/PRECAUCIÓN

Si usted no entiende la etiqueta, busque a alguien paraque se la explique a usted en detalle.

(If you do not understand the label, find someone toexplain it to you in detail.)

FOR MEDICAL EMERGENCIES ONLY CALL 24 HOURS A DAY 1-800-832-HELP (4357).

NET CONTENTS: _____

BASF Corporation26 Davis Drive Research Triangle Park, NC 27709

It is a violation of federal law to use thisproduct in a manner inconsistent with itslabeling.

• For sale to, use and storage only byindividuals/firms licensed or registered bythe state to apply termiticide and/orgeneral pest control products.

• DO NOT use this product for termite or otherpest control indoors, except for label-specified applications for termite control andfoam applications to wall voids for control ofother listed pests.

• DO NOT use on golf course turf. May be usedfor control of termites and other listed pestsfound on/near structures associated with golfcourses, but only as specified on this label.

• DO NOT use on/in commercial bee hives.• DO NOT use on animal trophies or animal

skins.

See inside booklet for additional Restrictions,First Aid, Precautionary Statements,Directions For Use, Conditions of Sale andWarranty, and state-specific use sites and/orrestrictions.

[Decal]Return to Index...

TERMIDOR® SCTERMITICIDE/INSECTICIDE

For sale to, use and storage only by individuals/firms licensed or registered by the state to apply termiticide

and/or general pest control products.

ACTIVE INGREDIENT:fipronil: 5-amino-1-(2,6-dichloro-4-(trifluoromethyl) phenyl)-4-((1,R,S)-(trifluoromethyl)sulfinyl)-1-H-pyrazole-3-carbonitrile . . . . . . . . . . . . . . . . . . . . . . 9.1%OTHER INGREDIENTS: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90.9%TOTAL: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100.0%One gallon of Termidor® SC termiticide/insecticide contains 0.8 lb of fipronil.


KEEP OUT OF REACH OF CHILDREN.CAUTION/PRECAUCIÓNSi usted no entiende la etiqueta, busque a alguien

para que se la explique a usted en detalle.(If you do not understand the label, find someone

to explain it to you in detail.)

For Product Use Information, Call 1-877-TERMIDOR

See inside for additional First Aid, Precautionary Statements and Directions for Use.

FOR MEDICAL AND TRANSPORTATION EMERGENCIES ONLY CALL 24 HOURS A DAY 1-800-832-HELP (4357).

[Booklet Front Panel]



CAUTIONHarmful if swallowed, absorbed through skin or inhaled.DO NOT get in eyes, on skin or on clothing. DO NOTbreathe spray mist. Wash thoroughly with soap and waterafter handling and before eating, drinking, chewing gum orusing tobacco. Remove and wash contaminated clothingbefore reuse.

PERSONAL PROTECTIVE EQUIPMENT (PPE)All pesticide handlers (mixers, loaders, and applicators)must wear long-sleeved shirt and long pants, socks,shoes, and chemical-resistant gloves. All pesticide han-dlers must wear a dust/mist filtering respirator(MSHA/NIOSH approval number prefix TC-21C), or aNIOSH approved respirator with any N, R, P or HE filter,when working in a non-ventilated space, including but notlimited to crawl-spaces and basements. All pesticide han-dlers must wear protective eyewear (goggles, a faceshield,or safety glasses with front, brow, and temple protection)when working in a non-ventilated space, including but notlimited to crawl-spaces and basements or when applyingtermiticide by rodding or sub-slab injection.

Follow the manufacturer’s instructions for cleaning/main-taining PPE. If no such instructions for washables, usedetergent and hot water. Keep and wash PPE separatelyfrom other laundry. Discard clothing or other absorbentmaterials that have been drenched or heavily contaminat-ed with this product’s concentrate. DO NOT reuse them.

ENVIRONMENTAL HAZARDSThis pesticide is toxic to birds, fish, and aquatic inverte-brates. DO NOT apply directly to water, or to areas wheresurface water is present or to intertidal areas below themean high water mark. Runoff from treated areas may behazardous to aquatic organisms in neighboring areas.Care must be taken to avoid runoff. DO NOT contaminatewater by cleaning equipment or disposal of wastes.DO NOT contaminate water when disposing of equipmentwashwaters or rinsate.

DIRECTIONS FOR USEIt is a violation of federal law to use this product in a man-ner inconsistent with its labeling.

Termidor® SC termiticide/insecticide cannot be usedto formulate, reformulate or repackage into any other pes-ticide product without the written permission of BASFCorporation.

Read entire label before using this product.

For sale to, use and storage only by individuals/firmslicensed or registered by the state to apply termiticideand/or general pest control products. States may havemore restrictive requirements regarding qualifications ofpersons using this product. Consult the structural pestcontrol regulatory agency of your state prior to use of thisproduct.

USER SAFETY RECOMMENDATIONSWash thoroughly with soap and water after handling. Washhands before eating, drinking, chewing gum, using tobacco orusing the toilet. Remove clothing/PPE immediately if pesticidegets inside. Then wash thoroughly and put on clean clothing.Remove PPE immediately after handling this product. Wash theoutside of gloves before removing. As soon as possible, washthoroughly and change into clean clothing.

2

FIRST AID

IF SWALLOWED

• Immediately call a poison control center or doctor.• DO NOT induce vomiting unless told to by a poison control center or doctor.• DO NOT give any liquid to the person.• DO NOT give anything by mouth to an unconscious person.

IF ON SKIN ORCLOTHING

• Take off contaminated clothing.• Rinse skin immediately with plenty of water for 15-20 minutes.• Call a poison control center or doctor for treatment advice.

IF INHALED

• Move person to fresh air.• If person is not breathing, call 911 or ambulance, then give artificial respiration, preferably

mouth to mouth if possible.• Call a poison control center or doctor for treatment advice.

IF IN EYES• Hold eye open and rinse slowly and gently with water for 15-20 minutes. Remove contact lenses,

if present, after the first 5 minutes, then continue rinsing eye.• Call a poison control center or doctor for treatment advice.

Have the product container or label with you when calling a poison control center or doctor, or going for treatment.

NOTE TO PHYSICIAN: There is no specific antidote. All treatment should be based on observed signs and symptoms of distress inthe patient. Overexposure to materials other than this product may have occurred. In severe cases of overexposure by oral ingestion,lethargy, muscle tremors, and in extreme cases, possibly convulsions may occur.

For medical emergencies call 24 hours a day 1-800-832-HELP (4357).

[Start of Booklet Text]


DO NOT contaminate water, food, or feed by storage ordisposal.

STORAGEStore unused product in original container only, out ofreach of children and animals.

PESTICIDE DISPOSALPesticide wastes are acutely hazardous. Improper disposalof excess pesticide is a violation of federal law. If thesewastes cannot be disposed of by use according to labelinstructions, contact your State Pesticide or EnvironmentalControl Agency, or the Hazardous Waste representative atthe nearest EPA Regional Office for guidance.

CONTAINER HANDLINGNonrefillable Container. DO NOT reuse or refill thiscontainer. Triple rinse or pressure rinse container (orequivalent) promptly after emptying; then offer for recy-cling, if available, or reconditioning, if appropriate, or punc-ture and dispose of in a sanitary landfill, or by incineration,or by other procedures approved by state and localauthorities.

Triple rinse containers small enough to shake(capacity ≤≤ 5 gallons) as follows: Empty the remain-ing contents into application equipment or a mix tankand drain for 10 seconds after the flow begins to drip.Fill the container 1/4 full with water and recap. Shake for10 seconds. Pour rinsate into application equipment ora mix tank, or store rinsate for later use or disposal.Drain for 10 seconds after the flow begins to drip.Repeat this procedure two more times.

Pressure rinse as follows: Empty the remaining con-tents into application equipment or mix tank. Hold con-tainer upside down over application equipment or mixtank, or collect rinsate for later use or disposal. Insertpressure rinsing nozzle in the side of the container andrinse at about 40 PSI for at least 30 seconds. Drain for10 seconds after the flow begins to drip.

In case of minor spills or leaks, soak up with sand, earthor other suitable material and dispose of as pesticidewaste.

USE RESTRICTIONS

• When treating adjacent to an existing structure, theapplicator must check the area to be treated, andimmediate adjacent areas of the structure, for visibleand accessible cracks and holes to prevent any leaksor significant exposures to persons occupying thestructure. People present or residing in the structureduring application must be advised to remove theirpets and themselves from the structure if they see anysigns of leakage. After application, the applicator is

required to check for leaks. All leaks resulting in thedeposition of termiticide in locations other than thoseprescribed on this label must be cleaned up prior toleaving the application site. DO NOT allow people orpets to contact contaminated areas or to reoccupycontaminated areas of the structure until the clean up iscompleted.

• Prior to drilling and treating through concrete struc-tures, such as patios, porches, sidewalks and founda-tion slabs applicator should first determine that thereare no habitable areas below that could be unintention-ally contaminated by the treatment.

• Only protected applicators wearing personal protectiveequipment as required by this product label may be inthe area during application.

• All holes in commonly occupied areas into whichTermidor® SC termiticide/insecticide has beenapplied must be plugged. Plugs must be of a non-cellulose material or covered by an impervious, non-cellulose material.

• DO NOT apply finished dilution of Termidor SC untilall heating/air conditioning ducts, air vents, plumbingpipes, sewer lines, floor drains, heating pipes and elec-trical lines/conduits are known and identified. DO NOTpuncture or contaminate any of these.

• DO NOT treat within a distance of one foot out fromthe drip line of edible plants.

• DO NOT contaminate public and private watersupplies.

• DO NOT make treatments while precipitation isoccurring.

• DO NOT treat soil that is water-saturated or frozen.• Use anti-backflow or air gap equipment with filling

hoses.

GENERAL INFORMATION

Termidor SC, when used as recommended in this label,provides effective prevention and/or control of subter-ranean termites. In order to maximize the termiticidepotency of Termidor SC, it should be applied in a mannerto provide a continuous treated zone to prevent termitesfrom infesting the wood to be protected.

Termidor SC should only be applied by licensed techni-cians familiar with trenching, rodding, short rodding, sub-slab injection, low-pressure banded surface applications,and foam delivery techniques. Termidor SC is highlyeffective against a variety of subterranean termites includ-ing species of Reticulitermes, Zootermopsis,Heterotermes, and Coptotermes. While Termidor SC islabeled for use at 0.06%, 0.09% or 0.125% finished dilu-tion, the 0.06% finished dilution should be used for typicalcontrol situations. Where severe termite infestations occur,where problem soils occur or where difficult or problemconstruction types are encountered, it may be advisable touse either 0.09% or 0.125% Termidor SC.

Termidor SC is formulated as a water-based suspensionconcentrate liquid containing 9.1% active ingredient.

DIRECTIONS FOR USETO CONTROL TERMITES

3

MIXING INSTRUCTIONSMix Termidor® SC termiticide/insecticide in the follow-ing manner:

1. Fill tank 1/4 - 1/3 full with water. Filling hose must beequipped with an anti-backflow device or water flowmust include an air gap to protect against backsiphoning.

2. Start pump to begin by-pass agitation and place endof treating tool in tank to allow circulation throughhose.

3. Add appropriate amount of Termidor SC. Refer to thetable in the box below to determine the proper amountto add to prepare the desired amount of finished dilu-tion.

4. Add remaining amount of water.5. Let pump run and allow recirculation through the hose

back into the tank until Termidor SC in the tank hasdispersed completely.

* Percentage weight of active ingredient to weight of spray dilution.

APPLICATION VOLUMETo provide maximum control and protection against termiteinfestation, apply the volumes of Termidor SC finisheddilution specified in the DIRECTIONS FOR USE through-out this label. However, if the soil will not accept theselabeled volumes of Termidor SC, twice the concentrationof Termidor SC may be applied in half the volume of fin-ished dilution. For example, if 0.06% Termidor SC cannotbe applied to achieve 4 gallons finished dilution per 10 lin-ear feet per foot of depth, then 0.125% Termidor SCapplied in 2 gallons finished dilution per 10 linear feet perfoot of depth may be substituted. DO NOT treat while

precipitation is occurring. DO NOT treat soil that is water-saturated or frozen or in any conditions where runoff ormovement from the treatment area (site) is likely to occur.

NOTE: Large reductions of application volume reduce theability to obtain a continuous treated zone. Variance isallowed when volume and concentration are consistentwith label-directed rates and a continuous treated zone isstill achieved. At reduced application volume, it may benecessary for the applicator to drill holes closer than12 inches apart to create a continuous treated zone.

PRE-CONSTRUCTION TREATMENT

DO NOT APPLY AT A DOSAGE AND/OR CONCENTRA-TION LOWER THAN TERMIDOR SC AT 0.06% FORAPPLICATIONS UP TO AND INCLUDING INSTALLATIONOF THE FINAL GRADE. Prior to each application, applica-tors must notify the general contractor, construction super-intendent, or similar responsible party, of the intendedTermidor SC application and intended sites of applicationand instruct the responsible person to notify constructionworkers and other on site individuals to leave the treat-ment area and not return until Termidor SC has beenabsorbed into the soil.

GENERALPre-construction treatments are defined to include treat-ments made during all phases of construction up to andincluding installation of the final grade. Effective pre-construction termite control is achieved by establishing athorough and complete horizontal and vertical treatedzone using 0.06%, 0.09% or 0.125% Termidor SC.

When treating foundations deeper than 4 feet, apply thetermiticide as the backfill is being replaced, or, if the con-struction contractor fails to notify the applicator to permitthis, treat the foundation to a minimum depth of 4 feetafter the backfill has been installed. The applicator musttrench and rod into the trench or trench along the founda-tion walls and around pillars and other foundation ele-ments, at the rate prescribed from grade to a minimumdepth of 4 feet. When the top of the footing is exposed,the applicator must treat the soil adjacent to the footing toa depth not to exceed the bottom of the footing. However,in no case should a structure be treated below the footing.

CONCRETE SLAB (INCLUDING MONO-LITHIC, FLOATING AND SUPPORTEDCONCRETE SLABS) ON GROUND OR INBASEMENTSHORIZONTAL TREATED ZONESApply an overall treatment of Termidor SC to the entiresurface to be covered beneath the concrete slab. Thisincludes the slab under the actual living area, plus car-ports, porches, basement floors, and any extendedentrances. Make this treatment at the rate of 1-1.5 gallonsfinished dilution per 10 square feet. Make these applica-tions using a coarse spray nozzle and low-pressure spray(less than 25 p.s.i.), spraying the dilution evenly and uni-formly over the entire area treated.

To Mix 0.125% DesiredFinished Dilution of Termidor SC*

Start with(gallons of

water)

Add (fluid ounces of Termidor SC)

100 gallons finished dilution 98 156 fl oz (or 1 gal + 28 fl oz)

50 gallons finished dilution 49.75 78 fl oz (or 2 qt + 14 fl oz)


1 gallon of finished dilution 1 1.6 fl oz

To Mix 0.09% DesiredFinished Dilution of

Termidor SC*

Start with(gallons of

water)


100 gallons finished dilution 99 117 fl oz (or 3 qt + 21 fl oz)


25 gallons finished dilution 24.75 29 fl oz (or 1 pt + 13 fl oz)


To Mix 0.06% DesiredFinished Dilution of

Termidor SC*

Start with (gallons of

water)




25 gallons finished dilution 24.75 19 fl oz (or 1 pt + 3 fl oz)


4

VERTICAL TREATED ZONESApply Termidor® SC termiticide/insecticide at rate of1 gallon finished dilution/square foot around anything pen-etrating the slab (e.g. utility services, plumbing lines) andat 4 gallons of finished dilution per 10 linear feet per footof depth along the inside and outside perimeter of founda-tion walls. The applicator must trench and rod into thetrench or trench along the foundation walls and around pil-lars and other foundation elements. Make this treatmentalong the inside of foundation walls at the rate of 4 gallonsfinished dilution (0.06%, 0.09% or 0.125% Termidor SC)per 10 linear feet per foot of depth, or if the footing ismore than 4 feet below grade, to a minimum depth of4 feet below grade. A trench need not be wider than sixinches. Low-pressure spray (less than 25 p.s.i. at the noz-zle) may be used to treat soil which will be replaced in thetrench. When rodding from grade or from the bottom of ashallow trench, rod holes should be spaced in a mannerthat will allow for application of a continuous treated zone,but not wider than 12 inches apart. Rod holes should notextend below the top of the footing.

These two applications, horizontal treated zone (overalltreatment 1-1.5 gallons/10 square feet) and vertical treat-ed zone (the additional treatment of 4 gallons/10 linearfeet) should be made prior to covering area with the con-crete slab. If slab is poured prior to horizontal treatment,Termidor SC can be used to treat penetrations, joints,bath traps, shower pan accesses, etc. as detailed inPost-Construction treatment section of label. However, itis highly recommended that a complete horizontal treatedzone be created prior to slab pour). If the slab is not to bepoured the same day as treatment, cover the treated soilwith a waterproof barrier such as polyethylene sheeting.

After completion of the grading, apply Termidor SC bytrenching and rodding into the trench or trenching alonealong the slab or foundation perimeter at the rate of 4 gal-lons finished dilution (0.06%, 0.09% or 0.125% TermidorSC) per 10 linear feet per foot of depth, or if the footing ismore than 4 feet below grade, to a minimum depth of4 feet. Trenches must be a minimum of 6 inches deep orto the bottom of the footing and need not be wider than6 inches. When trenching in sloping (tiered) soil, the trenchmust be stepped to ensure adequate distribution and toprevent Termidor SC from running out of the trench. Thefinished dilution (0.06%, 0.09% or 0.125% Termidor SC)should be mixed with the soil as it is replaced in thetrench. Rod holes must be spaced so as to achieve acontinuous treated zone but in no case more than 12inches apart. However, in no case should the structure betreated below the footing.

CRAWL SPACESFor crawl spaces, apply vertical termiticide treatment atthe rate of 4 gallons of finished dilution (0.06%, 0.09% or0.125% Termidor SC) per 10 linear feet per foot of depthfrom grade to the top of the footing, or if the footing ismore than 4 feet below grade, to a minimum depth of4 feet. Apply by trenching and rodding into the trench, ortrenching. Treat both sides of foundation and all piers and

pipes. When the top of the footing is exposed, the appli-cator must treat the soil adjacent to the footing to a depthnot to exceed the bottom of the footing.



• Trenches must be a minimum of 6 inches deep or tothe bottom of the footing, whichever is less, and neednot be wider than 6 inches. When trenching in sloping(tiered) soil, the trench must be stepped to ensure ade-quate distribution and to prevent termiticide from run-ning off. The finished dilution must be mixed with soilas it is replaced in the trench.

HOLLOW BLOCK FOUNDATIONS/VOIDSHollow block foundations or voids in masonry resting atopthe footing may be treated in order to create a continuoustreatment zone in the area to be treated. Applicators maydrill and treat into voids of masonry elements if not openlyaccessible. Apply at the rate of 2 gallons of finished dilu-tion per 10 linear feet of footing using a nozzle pressure of25 p.s.i. or less. When using this treatment, access holesmay be drilled below the sill plate and should be as closeas possible to the footing as is practical. Treatment ofvoids in block or rubble foundation walls must be closelyexamined: Applicators must inspect areas of possiblerunoff as a precaution against application leakage in thetreated areas. Some areas may not be treatable or mayrequire mechanical alteration prior to treatment.

All leaks resulting in the deposition of Termidor SC inlocations other than those prescribed on this label mustbe cleaned up prior to leaving the application site.DO NOT allow people or pets to contact contaminatedareas or to reoccupy the contaminated areas of the struc-ture until the clean up is completed.


POST-CONSTRUCTION CONVENTIONALSTRUCTURAL TERMITE TREATMENT

GENERALFor applications made after the final grade is installed forthe purpose of protecting the structure from termite infes-tation and/or for controlling existing termite populations.The applicator must trench and rod into the trench ortrench along the foundation walls and around pillars andother foundation elements, at either 0.06%, 0.09% or0.125% Termidor SC from grade to the top of the foot-ing. When the footing is more than four (4) feet belowgrade, the applicator must trench and rod into the trenchor trench along the foundation walls, at either 0.06%,0.09% or 0.125% Termidor SC, to a minimum depth offour feet. The actual depth of treatment will vary depend-ing on soil type, degree of compaction, and location oftermite activity. When the top of the footing is exposed,the applicator must treat the soil adjacent to the footing to

5

a depth not to exceed the bottom of the footing. However,in no case should a structure be treated below the footing.

Exterior concrete structures adjoining the foundation, suchas patios, porches and sidewalks, may be drilled followedby treatment by sub-slab injection of the Termidor® SCtermiticide/insecticide dilution in order to complete theexterior perimeter treatment zone along the foundationwall.

DO NOT apply finished dilution (0.06%, 0.09% or 0.125%Termidor SC) until the location and type of (1) construc-tion of heat or air-conditioning ducts and vents, (2) waterand sewer (or plumbing) lines and (3) electrical lines/con-duits are known and identified. Caution must be taken toavoid contamination of and damage to these structuralelements and airways.

CONCRETE SLAB OVER SOIL (INCLUDINGMONOLITHIC, FLOATING AND SUPPORTEDCONCRETE SLABS)EXTERIOR PERIMETERApply by trenching and rodding into the trench or trench-ing along the foundation at the rate of 4 gallons finisheddilution (0.06%, 0.09% or 0.125% Termidor SC) per10 linear feet per foot of depth, or, if the footing is morethan 4 feet below grade, to a minimum depth of 4 feet.Trenches must be a minimum of 6 inches deep or to thebottom of the footing and need not be wider than 6 inch-es. The finished dilution (0.06%, 0.09% or 0.125%Termidor SC) should be mixed with the soil as it isreplaced in the trench. Rod holes must be spaced so asto achieve a continuous treated zone but in no case morethan 12 inches apart. However, in no case should thestructure be treated below the footing.

SUB-SLAB INJECTIONSub-slab injection treatments can be made from inside thestructure or in cases when this is not possible, by drillingthrough the foundation from the outside as directed below.Prior to making any treatments, locate all heating/air con-ditioning ducts, vents, water/sewer lines, and electricallines/conduits.

Vertical Drilling/Injection: To treat under the slab, drillvertically through the slab along the interior perimeter ofthe foundation including the garage. Drill holes along allconcrete expansion joints, cracks, plumbing, and utilityservices penetrating the slab. It may be necessary to drillholes along one side of the slab adjacent to an interiorpartition wall if there is clear evidence of termite activity ordamage in the wall. All drill-holes through the slab shouldbe spaced so as to achieve a continuous treated zone butin no case be more than 12 inches apart. Inject a 0.06%,0.09% or 0.125% dilution of Termidor SC into the drilledholes at the rate of 4 gallons per 10 linear feet per foot ofdepth. For best results, application should be made with alateral dispersal nozzle. All holes in commonly occupiedareas into which material has been applied must beplugged. Plugs must be of a non-cellulose material or cov-ered by an impervious, non-cellulose material.

Horizontal Drilling/Rodding/Sub-slab Injection fromthe Exterior of the Foundation: This technique shouldbe used to treat underneath the slab only when floors orinterior design do not allow for vertical drilling. Care mustbe exercised not to rod into heating ducts, water/sewerlines, and electrical lines/conduits. Horizontal short-rodding practices can be used to establish a continuoustreated zone in the soil proximal to the inside of the foun-dation wall. Holes should be drilled from outside the foun-dation at an angle which allows a finished dilution (0.06%,0.09% or 0.125%) of Termidor SC to be deposited belowheating ducts, water/sewer lines, and electrical conduits ifpresent. Horizontal long rodding practices may only beemployed to treat areas underneath the slab that are notaccessible by vertical rodding or horizontal short rodding.Long rods exceeding 20 feet should not be used. For allhorizontal rodding applications, all drill holes through thefoundation should be spaced so as to achieve a continu-ous treated zone but in no case be more than 12 inchesapart. Inject a 0.06%, 0.09% or 0.125% dilution ofTermidor SC into the drilled holes at the rate of 4 gallonsper 10 linear feet per foot of depth. For best results, makeapplications with a lateral dispersal nozzle. All holes mustbe plugged. Plugs must be of a non-cellulose material orcovered by an impervious, non-cellulose material.

Bath Traps: Exposed soil or soil covered with tar or simi-lar sealant beneath or around plumbing and/or drain pipeentry areas should be treated with a minimum of 1 gallonbut no more than 4 gallons of finished dilution per squarefoot. Tar or sealant may have to be removed to allow foradequate soil treatment. An access door or inspectionportal should be installed, if not already present. Afterinspection and removal of all wood/cellulose debris, thesoil can be treated by rodding or drenching the soil with a0.06%, 0.09% or 0.125% dilution of Termidor SC.

SHOWER DRAINS: Soil beneath and adjacent to showerpan drains may be treated. Drill through slab adjacent toshower pan and apply 0.06%, 0.09% or 0.125% finishedspray dilution of Termidor SC by sub-slab injection to thesoil below. Foam can be used to maximize dispersion.Multiple access points may be drilled adjacent to thedrain. A directional dispersion tip may be used to enhancetreatment of the soil below the drain. Treat soil with a mini-mum of 1 gallon but no more than 4 gallons finished spraydilution per shower drain. Horizontal rodding can be usedto access and treat the soil associated with the showerdrain.

STRUCTURES WITH FRENCH DRAINSAND SUMP PUMPSFrench drains eliminate water at the footer along a founda-tion perimeter. They are common in hollow block founda-tion structures to drain water seeping from the exteriorperimeter or underneath the foundation. Soil must be drybefore applying to sites with French drains. DO NOT treatsoil that is saturated or frozen. DO NOT make treatmentswhile precipitation is occurring. DO NOT rod through theslab any closer than 24 inches to the French drain to pre-vent finished dilution seepage and/or damage to the drain

6

or the tiles. DO NOT apply Termidor® SCtermiticide/insecticide within 5 feet of the sump pumppit and pump. DO NOT drill through hollow block founda-tions that border the French drain in order to preventdrainage/seepage from the block into the drain.

Once French drains have been identified and located,apply Termidor SC as follows:

1) Unplug the sump pump. Inspect sump pit for water. Ifno water is present, the treatment can be made pro-vided the sump pump remains unplugged, or

2) if water is in the sump pit, unplug the sump pump andremove four cups of water from the pit. Mark the waterlevel. Wait 10 minutes and check the water level in thepit again. If the water level has risen, there is too muchseepage to perform the treatment at this time. If thewater level does not rise, make the treatment providedthe sump pump remains unplugged.

During application, check the sump pump pit every fewminutes for the presence of termiticide dilution. If dilution isdetected, stop treatment immediately and remove dilutionfrom the pump pit. All dilution must be removed from thesump pump pit before plugging in the sump pump again.Dispose of dilution from the sump pump as directed bythis label in the PESTICIDES DISPOSAL section.

BASEMENT STRUCTURESEXTERIOR PERIMETERApply by trenching and rodding into the trench or trench-ing along the foundation at the rate of 4 gallons finisheddilution (0.06%, 0.09% or 0.125% dilution of TermidorSC) per 10 linear feet per foot of depth, or if the footing ismore than 4 feet below grade, to a minimum depth of4 feet. Trenches must be a minimum of 6 inches deep orto the bottom of the footing and need not be wider than6 inches. When trenching in sloping tiered soil, the trenchmust be stepped to ensure adequate distribution and toprevent Termidor SC from running out of the trench. Thefinished dilution (0.06%, 0.09% or 0.125% of TermidorSC) should be mixed with the soil as it is replaced in thetrench. Rod holes must be spaced so as to achieve acontinuous treated zone but in no case more than12 inches apart. However, in no case should the structurebe treated below the footing.

INSIDE PERIMETERTo treat under the basement floor slab, drill verticallythrough the slab along the interior perimeter of the founda-tion. Drill holes along all concrete expansion joints, cracks,plumbing, and utility services penetrating the slab. Drillholes along both sides of partition foundation walls, andaround piers. It may be necessary to drill holes along oneside of the slab adjacent to a non-foundation interior parti-tion wall if there is clear evidence of termite activity in thewall. All drill holes through the slab should be spaced soas to achieve a continuous treated zone but in no case bemore than 12 inches apart. Inject a 0.06%, 0.09% or0.125% dilution of Termidor SC into the drilled holes atthe rate of 4 gallons per 10 linear feet per foot of depth.For best results, application should be made with a lateral

dispersal nozzle. All holes in commonly occupied areasinto which material has been applied must be plugged.Plugs must be of a non-cellulose material or covered byan impervious, non-cellulose material.

ACCESSIBLE CRAWL SPACECONSTRUCTIONBEFORE TREATMENT: Turn off any air circulationsystem that moves air from area to be treated to anuntreated interior space of the structure until appli-cation has been completed and all Termidor SC hasbeen absorbed by the soil.

For crawl spaces, apply vertical termiticide treatment atthe rate of 4 gallons of 0.06%, 0.09% or 0.125%Termidor SC per 10 linear feet per foot of depth fromgrade to the top of the footing, or if the footing is morethan 4 feet below grade, to a minimum depth of 4 feet.Apply by trenching and rodding into the trench, or trench-ing. Treat both sides of the foundation and around all piersand pipes. Where physical obstructions, such as concretewalkways adjacent to foundation elements, preventtrenching, treatment may be made by rodding alone.When soil type and/or conditions make trenching prohibi-tive, rodding may be used. When the top of the footing isexposed, the applicator must treat the soil adjacent to thefooting to a depth not to exceed the bottom of the foot-ing. Read and follow mixing and use directions on thislabel if situations are encountered where the soil will notaccept the full application volume.

• Rod holes and trenches must not extend below the bot-tom of the footing.


• Trenches must be a minimum of 6 inches deep or to thebottom of the footing, whichever is less, and need not bewider than 6 inches. When trenching in sloping (tiered)soil, the trench must be stepped to ensure adequate dis-tribution and to prevent termiticide from running off. The0.06%, 0.09% or 0.125% Termidor SC dilution mustbe mixed with the soil as it is replaced in the trench.

INACCESSIBLE CRAWL SPACECONSTRUCTIONBEFORE TREATMENT: Turn off any air circulationsystem that moves air from the area to be treated toan untreated interior space of the structure untilapplication has been completed and all Termidor SChas been absorbed by the soil.

For inaccessible interior areas, such as areas where thereis insufficient clearance between floor joists and groundsurfaces to allow operator access, excavate, if possible,and treat according to the instructions for accessible crawlspaces. Otherwise, apply one, or a combination of the fol-lowing two methods:

7

1. To establish a horizontal treated zone, apply to the soilsurface, 1 gallon of 0.06%, 0.09% or 0.125%Termidor® SC termiticide/insecticide per 10 squarefeet using a nozzle pressure of less than 25 p.s.i. and acoarse application nozzle (e.g., Delavan Type RDRaindrop®, RD-7 or larger, or Spraying Systems Co.80110LP Teejet® or comparable nozzle). For an areathat cannot be reached with the application wand, useone or more extension rods to make the application tothe soil. DO NOT broadcast or power spray with highpressures.

2. To establish a horizontal treated zone, drill through thefoundation wall or through the floor above and treat thesoil adjacent to the foundation wall at a rate of 1 gallonof 0.06%, 0.09% or 0.125% Termidor SC per10 square feet. Drill spacing must be at intervals not toexceed 16 inches. Many states have smaller intervalsso check state regulations which may apply. Soil adja-cent to foundation elements may be treated with shortor long rodding techniques without drilling, if access fortreatment tool to soil site is available.

HOLLOW BLOCK FOUNDATIONS/VOIDSHollow block foundations or voids in masonry resting atopthe footing may be treated. Drill and treat voids in multiplemasonry elements of the structure extending from thestructure to the soil in order to create a continuous treat-ment zone in the area to be treated. Applicators may drilland treat into voids of masonry elements if not openlyaccessible. Apply at the rate of 2 gallons of finished dilu-tion per 10 linear feet of footing using a nozzle pressure of25 p.s.i. or less. When using this treatment, access holesmay be drilled below the sill plate and should be as closeas possible to the footing as is practical. Treatment ofvoids in block or rubble foundation walls must be closelyexamined: Applicators must inspect areas of possiblerunoff as a precaution against application leakage in thetreated areas. Some areas may not be treatable or mayrequire mechanical alteration prior to treatment.

All leaks resulting in the deposition of Termidor SC inlocations other than those prescribed on this label mustbe cleaned up prior to leaving the application site.DO NOT allow people or pets to contact contaminatedareas or to reoccupy the contaminated areas of the struc-ture until the clean up is completed.


TREATMENT OF STRUCTURES WITHWELLS OR CISTERNSDO NOT contaminate wells or cisterns.DO NOT apply Termidor SC within 5 feet of any well orcistern. Soil between 5 and 10 feet from a well or cisternmust only be treated by the backfill method. Treatment ofsoil adjacent to water pipes within 3 feet of grade mustonly be done by the backfill method.

Backfill Method

1. Trench and remove soil to be treated onto heavy plas-tic sheeting or similar material or into a wheelbarrow.

2. Treat soil at the rate of 4 gallons of 0.06%, 0.09% or0.125% Termidor SC per 10 linear feet per foot ofdepth of the trench, or 1 gallon of 0.06%, 0.09% or0.125% Termidor SC per 1.0 cubic foot of soil. Mixthoroughly into the soil taking care to contain the liquidand prevent runoff or spillage.

3. After the treated soil has absorbed the Termidor SCfinished dilution, return the soil into the trench.

STRUCTURES WITH ADJACENT WELLS/CISTERNSAND/OR OTHER WATER BODIESApplicators must inspect all structures with nearby watersources such as wells, cisterns, surface ponds, streams,and other bodies of water and evaluate, at a minimum, thetreatment recommendations listed below prior to makingan application.

1. Prior to treatment, if feasible, expose the water pipe(s)coming from the well to the structure, if the pipe(s)enter the structure within 3 feet of grade. Treatment ofsoil adjacent to the water pipe(s) should be doneaccording to the backfill method described above.

2. Prior to treatment, applicators are advised to take pre-cautions to limit the risk of applying the termiticide intosubsurface drains that could empty into any bodies ofwater. These precautions include evaluating whetherapplication of Termidor SC to the top of the footermay result in contamination of the subsurface drain.Factors such as depth to the drain system, soil typeand degree of soil compaction should be taken intoaccount in determining the depth of treatment.

3. When appropriate (e.g., on the water side of the struc-ture), the treated backfill method (described above) canalso be used to minimize off-site movement ofTermidor SC.

4. Applicator may apply a 0.125% dilution at 2 gallons/10linear feet/foot of depth to minimize potential of runoffinto non-target areas.

PLENUM CONSTRUCTIONBEFORE TREATMENT: Turn off any air circulationsystem that moves air from the space to be treatedto an untreated interior space of the structure untilapplication has been completed and all Termidor SChas been absorbed by the soil.Application of Termidor SC to the soil exterior to thefoundation walls should follow the instructions listed abovein ACCESSIBLE CRAWL SPACE CONSTRUCTION,including instructions for sloping (tiered) soils.

Interior treatment of plenum structures that use a sealedunderfloor space to circulate heat and/or cooled airthroughout the structure need to follow the instructionsbelow:

1. Remove the sealing fabric and anything on the sealingfabric to expose no more than 18 inches adjacent to allfoundation structures, including foundation walls, interi-or piers, pipes, and any other structures with soil con-tact. Follow the instructions listed above for exterior

8

and interior treatment of ACCESSIBLE CRAWLSPACE CONSTRUCTION.

2. After the finished dilution of Termidor® SC termiti-cide/insecticide has been absorbed by the soil,replace the sealing fabric and anything to be placed onthe sealing fabric to its original, pre-treatment position.

FOAM APPLICATIONSConstruction practices, soil subsidence, and other factorsmay make it difficult to created a continuous treatmentzone. In such situations, conventional liquid applicationmethods can be supplemented through the use of foam-generating equipment. Treatment of filled stoops andporches, chimney bases, piers, soil under concrete slabs,into block voids, behind masonry, other veneers, and studwalls are examples where foam applications may be use-ful. Foam applications to wall voids in stud walls shouldutilize dry foam only (from a range of relatively dry foam of15:1 to 25:1 to 50:1 expansion ratio). Apply foam to wallvoids where termites or termite damage are present orsuspected.

In general, “foam only” treatment under slabs is appropri-ate when attempting to maximize horizontal coverage inareas where there is no deep foundation or footing (e.g.around plumbing entries, and near settlement cracks inconcrete slabs). In areas where both lateral spread anddeeper vertical penetration of the termiticide is neededboth foam and conventional liquid should be used (e.g.adjacent to foundation walls). Foam and liquid applicationsmust be consistent with volume and active ingredientinstructions in order to ensure proper application has beenmade. The volume and amount of active ingredient areessential to an effective treatment. At least 75% of the gal-lons of the 0.06%, 0.09% or 0.125% Termidor SC fin-ished dilution must be applied as a typical liquid treatment.The remaining 25% or less gallons should be delivered toappropriate locations using a foam application. The totalamount of product applied with the combination of foamand liquid finished dilution should be equivalent to that ofan application of liquid finished dilution only. Foam applica-tions are generally a good supplement to liquid treatmentsand they can be helpful in treating difficult areas.

FOAM MIXING INSTRUCTIONS AND APPLICATIONPrepare the finished dilution of Termidor SC and mix itwith manufacturer's recommended volume of foamingagent in foaming equipment. Apply a sufficient volume ofTermidor SC foam formulation to provide a continuoustreated zone at the recommended rate for specific appli-cations (these various rates are provided in the text of thislabel). If sufficient foam volume cannot be applied toachieve the recommended rate of Termidor SC, applyadditional finished dilution of Termidor SC as liquid toassure proper treatment volume and concentration in thetreated area.

MIXING TABLE FOR TERMIDOR SC FOAM

* Percentage weight of active ingredient to weight of spray dilution.

** Add the manufacturer’s recommended quantity of foam agent to theTermidor SC dilution.

POST-CONSTRUCTION EXTERIORPERIMETER/LOCALIZED INTERIOR (EP/LI)

STRUCTURAL TERMITE TREATMENT*

*Not approved for use in Louisiana.

GENERAL INFORMATIONFor post-construction applications after the final grade isinstalled for the purpose of protecting the structure fromtermite infestation and/or for controlling existing termitepopulations. Termidor SC can be used to protect struc-tures by using the Conventional structural treatment or theExterior Perimeter/Localized Interior structural treatment.Structural termite protection is achieved by first establish-ing a continuous treated zone along the exterior founda-tion of the structure. Localized interior treatments are thenmade to areas where known termite activity is observed. Ifno termite activity is observed inside the structure at treat-ment time, then interior local treatments are not required.

This treatment method is designed to be non-invasive tothe interior of the structure by applying a continuous treat-ment along the exterior foundation and only treating theinterior areas that show termite activity. It may not be aconventional complete treatment. If you have questionsregarding this treatment, consult your lead state agency.Termidor SC, when used as recommended in this label,provides effective subterranean termite control.

Termite activity is defined as one or more of the followinginfestation conditions: either alates (winged termites) haveswarmed inside the structure or live termites are found tobe active within the structure; or there is clear evidence oftermite activity on or in the structure (mud tubes, galleriesin wood) and live termites.

DO NOT apply Termidor SC as an ExteriorPerimeter/Localized Interior treatment at a finished dilutionconcentration lower than 0.06% or an application volumeless than that specified in the APPLICATION VOLUMEuse directions section of this label.

Termidor SC UseDilution

Gallons ofFinishedDilution

FoamExpansion

Ratio**

Finished Foam(gallons)

0.06%, 0.09% or0.125% ai *

1.01.662.55.0

25:115:110:15:1

25

9

A. EXTERIOR PERIMETER TREATMENT

When conducting an exterior perimeter application,Termidor® SC termiticide/insecticide must be appliedin a manner to provide a continuous treatment zone toprevent termites from infesting the structure. Read and fol-low APPLICATION VOLUME use directions on this labelif situations are encountered where the soil will not acceptthe full application volume recommended in the followinguse directions.

A.1 CONCRETE SLAB ON GROUND (INCLUDINGMONOLITHIC, FLOATING AND SUPPORTEDCONCRETE SLABS)

Apply along the exterior foundation perimeter by trenchingand rodding into the trench or trenching at the rate of4 gallons finished dilution (0.06%, 0.09% or 0.125%Termidor SC) per 10 linear feet per foot of depth.Trenches must be a minimum of 6 inches deep, or to thebottom of the footing, and need not be wider than 6 inch-es. The finished dilution must be mixed with the soil as it isreplaced in the trench. Rod holes must be spaced so asto achieve a continuous treatment zone but in no casemore than 12 inches apart. However, in no case shouldthe structure be treated below the footing.

Where physical obstructions, such as concrete walkwaysadjacent to foundation elements, prevent trenching, treat-ment may be made by rodding alone. When soil typeand/or conditions make trenching prohibitive, rodding maybe used with rod holes no more than 12 inches apart.Drilling and sub-slab treatment of sub-soil is necessary forexterior concrete structures adjoining the foundation suchas patios, porches and sidewalks, to complete the exteriorperimeter treatment zone. For driveways, exterior drilling isnecessary only around building supports or wall elementsthat are permanently and physically located at drivewayjoints. In no case should the structure be treated belowthe footing.

A.2 BASEMENT AND INACCESSIBLE CRAWLSPACE CONSTRUCTION

Apply along the exterior foundation perimeter by trenchingand rodding into the trench or trenching at the rate of 4gallons finished dilution (0.06%, 0.09% or 0.125%Termidor SC) per 10 linear feet per foot of depth fromgrade to the top of the footing, or if the footing is morethan 4 feet below grade, to a minimum depth of 4 feet.Trenches must be a minimum of 6 inches deep or to thebottom of the footing and need not be wider than 6 inch-es. When trenching in sloping or tiered soil, the trenchmust be stepped to ensure adequate distribution and toprevent Termidor SC from running out of the trench. Thefinished dilution must be mixed with the soil as it isreplaced in the trench. Rod holes must be spaced so asto achieve a continuous treatment zone but in no casemore than 12 inches apart. However, in no case shouldthe structure be treated below the footing.

Where physical obstructions, such as concrete walkwaysadjacent to foundation elements, prevent trenching, treat-ment may be made by rodding alone. When soil typeand/or conditions make trenching prohibitive, rodding may

be used with rod holes no more than 12 inches apart.Drilling and sub-slab injection treatment of sub-soil is nec-essary for exterior concrete structures adjoining the foun-dation such as patios, porches and sidewalks, to com-plete the exterior perimeter treatment zone. For driveways,exterior drilling is necessary only around building supportsor wall elements that are permanently and physically locat-ed at driveway joints. In no case should the structure betreated below the footing.

If termite activity is found inside an inaccessible crawlspace, the area with termite activity must be treated. Alocalized interior treatment must be made at the site of thetermite activity and at least 2 feet in both directions fromthe termite activity. Choose the appropriate applicationtechnique for treating INACCESSIBLE CRAWL SPACECONSTRUCTION from the Conventional treatment sec-tion of this label.

A.3 ACCESSIBLE CRAWL SPACESBEFORE TREATMENT: Turn off any air circulationsystem that moves air from area to be treated to anuntreated interior space of the structure until appli-cation has been completed and all Termidor SC hasbeen absorbed by the soil.

For crawl spaces, apply vertical termiticide treatment atthe rate of 4 gallons of 0.06%, 0.09% or 0.125%Termidor SC per 10 linear feet per foot of depth fromgrade to the top of the footing, or if the footing is morethan 4 feet below grade, to a minimum depth of 4 feet.Apply by trenching and rodding into the trench, or trench-ing. Treat outside the foundation and around all piers andpipes. Where physical obstructions, such as concretewalkways adjacent to foundation elements, preventtrenching, treatment may be made by rodding alone.When soil type and/or conditions make trenching prohibi-tive, rodding may be used. When the top of the footing isexposed, the applicator must treat the soil adjacent to thefooting to a depth not to exceed the bottom of the foot-ing. Drilling and sub-slab injection treatment of sub-soil isnecessary for exterior concrete structures adjoining thefoundation such as patios, porches and sidewalks, tocomplete the exterior perimeter treatment zone. Read andfollow mixing and use directions on this label if situationsare encountered where the soil will not accept the fullapplication volume.



• Trenches must be a minimum of 6 inches deep or tothe bottom of the footing, whichever is less, and neednot be wider than 6 inches. When trenching in sloping(tiered) soil, the trench must be stepped to ensure ade-quate distribution and to prevent termiticide from run-ning off. The 0.06%, 0.09% or 0.125% Termidor SCdilution must be mixed with the soil as it is replaced inthe trench.

10

A.4 GARAGES: Attached garage floors should be treat-ed in structures.

SUB-SLAB INJECTIONSub-slab injection treatments can be made from inside thegarage or in cases where this not possible, by drillingthrough the foundation from the outside as directed below.Prior to making any treatments, locate all heating/air con-ditioning ducts, vents, water/sewer lines, and electricallines/conduits.

Vertical Drilling/Injection: To treat under the slab, drillvertically through the slab along the interior perimeter ofthe garage foundation. Drill holes along all concreteexpansion joints, cracks, plumbing, and utility servicespenetrating the slab. It may be necessary to drill holesalong one side of the slab adjacent to an interior partitionwall if there is clear evidence of termite activity or damagein the wall. All drill holes through the slab should bespaced so as to achieve a continuous treatment zone butin no case be more than 12 inches apart. Inject a 0.06%,0.09% or 0.125% dilution of Termidor® SCtermiticide/insecticide into the drilled holes at the rateof 4 gallons per 10 linear feet per foot of depth. For bestresults, application should be made with a lateral dispersalnozzle. All holes in commonly occupied areas into whichmaterial has been applied must be plugged. Plugs mustbe of a non-cellulose material or covered by an impervi-ous, non-cellulose material such as Portland cement.

Horizontal Drilling/Rodding/Sub-slab Injection fromthe Exterior of the Garage Foundation: This techniqueshould be used to treat underneath the slab only wheninterior design does not allow for vertical drilling. Caremust be exercised not to rod into heating ducts,water/sewer lines, and electrical lines/conduits. Horizontalshort-rodding practices can be used to establish a con-tinuous treatment zone along the inside perimeter of thefoundation. Holes should be drilled from outside the foun-dation at an angle which allows a finished dilution (0.06%,0.09% or 0.125%) of Termidor SC to be deposited belowheating ducts, water/sewer lines, and electrical conduits ifpresent. Horizontal long rodding practices may only beemployed to treat areas underneath the slab that are notaccessible by vertical rodding or horizontal short rodding.Long rods exceeding 20 feet should not be used. For allhorizontal rodding applications, all drill holes through thefoundation should be spaced so as to achieve a continu-ous treatment zone but in no case be more than 12 inch-es apart. Inject a 0.06%, 0.09% or 0.125% dilution ofTermidor SC into the drilled holes at the rate of 4 gallonsper 10 linear feet per foot of depth. For best results, makeapplications with a lateral dispersal nozzle. All holes mustbe plugged. Plugs must be of a non-cellulose material orcovered by an impervious, non-cellulose material such asPortland cement.

B. LOCALIZED INTERIOR TREATMENTTargeted interior applications may be made to vulnerableareas such as around plumbing/utility lines penetratingfloors, bath and/or shower traps, or along expansion jointsor settlement cracks as part of a complete treatment.

However, if known termite activity exists (as describedabove in the section on general information) in areas insidethe living spaces (occupied areas of the structure) or non-living spaces (such as crawl spaces, plenums, etc.) of thestructure, a localized interior treatment must be made inthe immediate vicinity (at least 2 feet in two or more direc-tions radiating from the site) of the termite activity.

B.1 INTERIOR CONCRETE FLOORIf termite activity occurs in an interior wall or structuralmember, the area under the floor and behind the walladjacent to the evidence must be treated with TermidorSC at 0.06%, 0.09% or 0.125% finished dilution at a rateequal to 4 gallons per 10 linear feet. This localized interiortreatment must be made at the site of the termite activityand at least 2 feet in two or more directions radiating fromthe site. Foam can be used to maximize dispersion. Drillholes in commonly occupied areas must be plugged witha non-cellulose material or covered by an impervious, non-cellulose material such as Portland cement.

B.2 HOLLOW BLOCK FOUNDATIONS/VOIDSIf termite activity occurs in or in the vicinity (within 2 feet) ofhollow block foundations or voids in masonry resting onthe footing, the wall adjacent to the evidence must bedrilled, if not openly accessible, and Termidor SC at0.06%, 0.09% or 0.125% finished dilution must be inject-ed into the void at a rate equal to 2 gallons per 10 linearfeet of footing using a nozzle of 25 p.s.i. or less. Thislocalized interior treatment to hollow block must be madeat the site of the termite activity and to areas above thetermite activity. Treatment must be made at least 2 feet intwo or more directions radiating from the site of termiteactivity or along the wall pier or support post. Foam canbe used to maximize dispersion. When using this treat-ment, access holes should be drilled below the sill plateand should be as close to the footing as is practical.Treatment of voids in block or rubble foundation wallsmust be closely examined: Applicators must inspect areasof possible runoff as a precaution against application leak-age in the treated areas. Some areas may not be treatableor may require mechanical alteration prior to treatment. Allleaks resulting in the deposition of Termidor SC in loca-tions other than those prescribed on this label must becleaned up prior to leaving the application site. DO NOTallow people or pets to contact contaminated areas or toreoccupy the contaminated areas of the structure until theclean up is completed. The drilled holes in commonlyoccupied areas must be plugged with a non-cellulosematerial or covered by an impervious, non-cellulose mate-rial such as Portland cement.

B.3 BATH TRAPSIf termite activity is observed within 2 feet of the bath trap,then exposed soil or soil covered with tar or similar sealantaround plumbing and/or drainpipe entry areas must betreated. Tar or sealant may have to be removed to allowfor adequate soil treatment. An access door or inspectionportal should be installed if one is not already present.After inspection and removal of all wood/cellulose debris,the soil can be treated by rodding or drenching the soil

11

with a 0.06%, 0.09% or 0.125% dilution of Termidor® SCtermiticide/insecticide. Treat with a minimum of 1 gallonto a maximum of 4 gallons of finished dilution per squarefoot.

B.4 SHOWER DRAINSIf termite activity is observed within two feet of the showerdrains, then soil beneath and adjacent to shower drainsmust be treated. Drill through slab adjacent to showerdrain and apply 0.06%, 0.09% or 0.125% finished dilutionof Termidor SC by sub-slab injection to the soil below.Foam can be used to maximize dispersion. Multipleaccess points may be drilled adjacent to the drain. Adirectional dispersion tip may be used to enhance treat-ment of the soil below the drain. Treat soil with a minimumof 1 gallon but no more than 4 gallons finished spray dilu-tion per shower drain. Horizontal rodding can be used toaccess and treat the soil associated with the showerdrain.

RETREATMENT INSTRUCTIONS

Retreatment for subterranean termites can only be per-formed if there is clear evidence of reinfestation or disrup-tion of the treated zone due to construction, excavation,or landscaping and/or evidence of the breakdown of thetermiticide treated zone in the soil. These vulnerable orreinfested areas may be retreated using a spot, partial orcomplete treatment(s) in accordance with application tech-niques described on this label. The timing and type ofthese retreatments will vary depending on factors such astermite pressure, soil types, soil conditions and other fac-tors which may reduce the effectiveness of the treatedzone. Annual re-treatment of the structure is prohibitedunless there is clear evidence that reinfestation, treatmentzone disruption and/or evidence of breakdown hasoccurred.

USE WITH OTHER PRODUCTS

When a borate-based termite control product is used asthe primary pre-construction treatment for subterraneantermites and is applied in according to label directions foruse, Termidor SC may be applied as an exterior perime-ter pre-construction treatment using 0.06%, 0.09% or0.125% dilution. If the exterior perimeter pre-constructiontreatment option is selected, Termidor SC must beapplied to provide a continuous treated zone along theexterior foundation of the structure. A complete and thor-ough horizontal pre-construction treatment withTermidor SC under the concrete slab is optional.Termidor SC may also be applied to critical areas of theinterior of the structure. These areas include plumbing andutility entry sites, bath traps, shower drain penetrations,expansion joints, foundation cracks, and areas of knownor suspected termite activity.

For applications to the exterior perimeter and critical areasfollow the instructions in the POST-CONSTRUCTIONEXTERIOR PERIMETER/LOCALIZED INTERIOR(EP/LI) STRUCTURAL TERMITE TREATMENT sectionof this label.

POSTS, POLES, WOOD LANDSCAPEORNAMENTATION

DO NOT contaminate wells or cisterns.Preventative Treatment: Create a continuous chemicaltreatment zone in the soil around wooden posts, poles,fence posts, signs or landscape ornamentation. Apply a0.06%, 0.09% or 0.125% dilution of Termidor SC at therate of 4 gallons per 10 linear feet per foot of depth. Fortreatments made during installation, the finished dilutionmay be applied to soil as it is replaced around the post orpole. The finished application should place termiticide to adepth of six inches below the bottom of the posts, poles,or other wooden items in contact with the soil.

Curative Treatment: Previously installed poles, posts,landscape ornamentation, or signs may be treated with a0.06%, 0.09% or 0.125% finished dilution of TermidorSC by sub-surface injection or treated by gravity flowthrough holes made from the bottom of a trench aroundthe pole or post. When trenching, the trench need not bewider than 6 inches wide and 6 inches deep. When sub-surface injecting, treat all sides to create a continuoustreatment zone. Apply to a depth of six inches below thebottom of the wood.

TERMITES ABOVE GROUNDFor control of termite aerial colonies or drywood termites.In localized areas of wood structures, apply at a 0.06%,0.09% or 0.125% dilution of Termidor SC to areas ofwooden members/voids. Application may be made toinaccessible areas by drilling, and then injecting the fin-ished dilution with a crack and crevice injector into thedamaged wood or void spaces. Termidor SC foam appli-cations may be made to void spaces.

Termite carton nests in trees or building voids may beinjected with 0.06%, 0.09% or 0.125% dilution using apointed injection tool. Multiple injection points to varyingdepths may be necessary. It is desirable to physicallyremove carton nest material from building voids whensuch nests are found.

After application, the applicator is required to check forleaks resulting in deposition of treatment dilution in loca-tions other than those prescribed on this label. Whenfound, this material must be cleaned up prior to leavingthe application site. DO NOT allow people or pets to con-tact contaminated areas or to reoccupy contaminatedareas of the structure until the clean up is completed.

DO NOT TREAT FRUIT- OR NUT-BEARING TREES.

12

Listed structures are residential, institutional, commercialand industrial buildings and utility enclosures.

USE RESTRICTIONS

• Only protected applicators wearing personal protectiveequipment as required by this product label may be inthe area during application.

• DO NOT treat within a distance of one foot out fromthe drip line of edible plants.

• DO NOT contaminate public and private watersupplies.

• DO NOT contaminate water, food or feed. Cover orremove all exposed food, feed and drinking water.

• DO NOT apply to wasp or hornet nests if they are notattached to the structure exterior or inside wall voids.

• DO NOT make treatments while precipitation isoccurring.

• DO NOT allow residents, children, other persons orpets into the immediate area during application.DO NOT allow residents, children, other persons orpets into treated area until sprays have dried. Afterapplication, the applicator is required to check for leaksresulting in deposition of treatment dilution in locationsother than those prescribed on this label. When found,this material must be cleaned up prior to leaving theapplication site. DO NOT allow people or pets to con-tact contaminated areas or to reoccupy contaminatedareas of the structure until the clean up is completed.

• DO NOT spray air conditioning units or air intake vents.

• DO NOT use indoors except for applications into wallvoids.

• DO NOT exceed the maximum of two applications peryear.

• DO NOT apply to playground equipment and petquarters.

• DO NOT allow applications to runoff or drip from treat-ed surface.

• DO NOT apply to boat houses, including their piers orpilings.

• DO NOT apply within 5 feet of wells or cisterns.

• DO NOT apply to French drains or other permeabledrainage.

• Doors and windows adjacent to application site mustbe closed during surface application.

• DO NOT apply within 15 feet of bodies of fresh water:lakes, reservoirs, rivers, permanent streams, marshes,

natural ponds and commercial fish ponds. A 15-footbuffer of uniform groundcover must exist betweenapplication zone and bodies of fresh water (uniformground cover is defined as land which supports vege-tation of greater than 2 inches in height throughout.DO NOT apply within 60 feet of estuarine bodies ofwater. Estuarine water bodies are brackish, tidal waterbodies such as bays, mouths of rivers, salt marshesand lagoons.

Use Termidor® SC termiticide/insecticide to kill andprovide residual control of the following pests:ants (acrobat, Argentine, big-headed, carpenter, crazy,odorous, pavement, pharaoh, thief)

Use Termidor SC to kill the following pests:beetles (Asian lady, darkling);bugs (box-elder, pill);centipedes;cockroaches (Australian, Oriental, smokey brown);crickets, house;earwigs, European;flies, cluster;millipedes;silverfish;spiders (black widow, brown recluse, cellar, hobo);ticks, brown dog;wasps, paper*;yellow jackets

* Termidor is not a knockdown agent.

MIXING INSTRUCTIONS

To prepare 1 gallon of a 0.06% spray dilution, add 0.8 fl ozof Termidor SC to the treatment tank already 1/4 - 1/3filled with water. Filling hose must be equipped with ananti-backflow device or water flow must include an air gapto protect against back siphoning. While agitating addmore water to make 1 gallon of finished dilution.

To make treatment, continue agitation and apply a coarsespray using a low-pressure sprayer.

APPLICATIONS TO OUTSIDE SURFACES OF LISTEDSTRUCTURES AND INTO WALL VOIDS

Apply 0.06% Termidor SC finished dilution where listedpests enter the structure, where they trail or crawl andhide or where their nests are found. Treat using a low-pressure coarse banded surface spray up to 18 inches inwidth around doors, windows, vents, pipes or any otherexterior openings and/or with a crack and crevice injectiontip into foundation cracks or drilled holes where listedpests could enter the structure. Be especially careful totreat the joint where exterior siding (wood, vinyl, aluminumor any similar material) meets the cement, block or brickfoundation. Treat areas where any wires (electrical, tele-phone or cable) enter the house. Termidor SC foamapplications may be made to wall voids to kill/control listedpests. Refer to the Foam Applications section of thislabel for specific foam mixing and application instructions.

DIRECTIONS FOR USE TO CONTROL LISTED PESTS ON OUTSIDE

SURFACES AND ALONG FOUNDATIONPERIMETER OF LISTED STRUCTURES

13

APPLICATIONS TO PERIMETER OF LISTEDSTRUCTURES

Apply 0.06% Termidor® SC termiticide/insecticide fin-ished dilution as a low-pressure coarse general surfacespray along the foundation exterior perimeter to an areaone foot up and one foot out from where the groundmeets the foundation. Apply 2 quarts of 0.06%Termidor SC finished spray per 160 linear feet. (This rateis approximately 1.5 gallons finished spray per1000 square feet.) If nests are found on the ground withinone foot of the foundation, treatment of Termidor SC canbe made to these nests.

It is recommended to remove or prune away shrubbery,bushes, and tree branches touching the structure.Vegetation touching the structure may offer a route ofentry for ants into the structure. This may allow ants toinhabit the structure without coming in contact with thetreatment.

14

Termidor is a registered trademark of BASF.

Raindrop is a registered trademark of Delavan Corporation.

Teejet is a registered trademark of Spraying Systems Co.


007969-00210.20130510.NVA 2013-04-220-0094Supersedes: NVA 2012-04-220-0161



NOTICE TO BUYERPurchase of this material does not confer any rightsunder patents governing this product or the use thereofin countries outside the United States.

Termidor® termiticide/insecticide is specially formulat-ed and sold by BASF for the control of termites or pestsaccording to the directions on this label. The purchaseprice of Termidor® termiticide/insecticide includes aroyalty whereby the purchaser acquires a prepaid licenseunder the claims of U.S. Patent No. 5,801,189 for thecontrol of cockroaches to use only the specificTermidor® termiticide/insecticide purchased underthis label. The purchaser agrees to employ the pur-chased quantity of Termidor® termiticide/insecticideonly for the specified uses, including under BASF’sUnited States patent rights, and to provide notice of theterms and conditions of this license to any subsequentpurchaser. Uses of Termidor® termiticide/insecticideother than those specified on this label are not licensedthrough the purchase of this product and the use of thisproduct for other purposes may violate this license andpatent rights of BASF. The licensee under this labellicense assumes all risks as to the patents of others.BASF retains the right to terminate, modify, or restrict thislicense at any time.

Conditions of Sale and WarrantyThe Directions For Use of this product reflect theopinion of experts based on field use and tests. Thedirections are believed to be reliable and must befollowed carefully. However, it is impossible to eliminateall risks inherently associated with the use of thisproduct. Ineffectiveness or other unintendedconsequences may result because of such factors asweather conditions, presence of other materials, or useof the product in a manner inconsistent with its labeling,all of which are beyond the control of BASFCORPORATION (“BASF”) or the Seller. To the extentconsistent with applicable law, all such risks shall beassumed by the Buyer.

BASF warrants that this product conforms to thechemical description on the label and is reasonably fit forthe purposes referred to in the Directions For Use,subject to the inherent risks, referred to above.

TO THE EXTENT CONSISTENT WITH APPLICABLELAW, BASF MAKES NO OTHER EXPRESS ORIMPLIED WARRANTY OF FITNESS ORMERCHANTABILITY OR ANY OTHER EXPRESS ORIMPLIED WARRANTY.

TO THE EXTENT CONSISTENT WITH APPLICABLELAW, BUYER’S EXCLUSIVE REMEDY AND BASF’SEXCLUSIVE LIABILITY, WHETHER IN CONTRACT,TORT, NEGLIGENCE, STRICT LIABILITY, OROTHERWISE, SHALL BE LIMITED TO REPAYMENTOF THE PURCHASE PRICE OF THE PRODUCT.

TO THE EXTENT CONSISTENT WITH APPLICABLELAW, BASF AND THE SELLER DISCLAIM ANYLIABILITY FOR CONSEQUENTIAL, EXEMPLARY,SPECIAL OR INDIRECT DAMAGES RESULTINGFROM THE USE OR HANDLING OF THISPRODUCT.

BASF and the Seller offer this product, and the Buyerand User accept it, subject to the foregoing Conditionsof Sale and Warranty which may be varied only byagreement in writing signed by a duly authorizedrepresentative of BASF. PC309

15

Liqu

id A

nt B

aits

Ant K

iller

II

Index....

KILLS ON CONTACT FROM 15 FEET AWAY

For Outdoor Use Only

KILLS: Bees, Hornets, Spiders, Yellowjackets and WaspsACTIVE INGREDIENTS:d-trans Allethrin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.129%Phenothrin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.120%OTHER INGREDIENTS:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99.751%Contains petroleum distillate. TOTAL: 100.000%

EPA Reg. No. 499-362


CAUTION

FIRST AIDIF SWALLOWED: Immediately call a poisoncontrol center or doctor. Do not induce vomiting unless told to do so by a poisoncontrol center or doctor. Do not give ANY liquid to the person. Do not give anything bymouth to an unconscious person.IF ON SKIN OR CLOTHING: Take off contaminated clothing. Rinse skin immediatelywith plenty of water for 15 - 20 minutes. Call a poison control center or doctor fortreatment advice.IF IN EYES: Hold eyes open and rinse slowlyand gently with water for 15 - 20 minutes.Remove contact lenses, if present, after thefirst 5 minutes, then continue rinsing eyes.Call a poison control center or doctor fortreatment advice.IF INHALED: Move person to fresh air. If person is not breathing, call 911 or anambulance, then give artificial respiration,preferably by mouth-to-mouth, if possible.Call a poison control center or doctor for further treatment advice.

Have the product container or label with you when calling a poison control center or doctor,or going for treatment. You may also call 1-800-225-3320 for emergency medicaltreatment informationNOTE TO PHYSICIAN: Contains petroleumdistillate - vomiting may cause aspirationpneumonia.

PRECAUTIONARY STATEMENTS HAZARDS TO HUMANS

AND DOMESTIC ANIMALSCAUTION: Harmful if swallowed, inhaled, orif absorbed through the skin. Avoid breathingvapors or spray mist. Avoid contact with skin,eyes or clothing. Wash thoroughly with soapand water after handling. Remove contaminatedclothing and wash clothing before reuse.

ENVIRONMENTAL HAZARDSThis pesticide is highly toxic to fish. Do notapply directly to water or to areas where surface water is present or to intertidal areasbelow the mean high water mark. Do not contaminate water by cleaning of equipment or disposal of equipment washwaters.

PHYSICAL HAZARDSFlammable. Contents under pressure. Keepaway from heat, sparks and open flame. Do notpuncture or incinerate container. Exposure totemperatures above 130°F may cause burst-ing. May cause staining (darkening) of asphaltsurfaces and shingles.

DIRECTIONS FOR USEIT IS A VIOLATION OF FEDERAL LAW

TO USE THIS PRODUCT IN A MANNERINCONSISTENT WITH ITS LABELING.

For optimum performance in overhead treat-ments, align the actuator opening with themark on valve cup. When treating in a down-ward direction, align the actuator openingdirectly opposite the mark on valve cup.

WHITMIRE MICRO-GENRESEARCH LABORATORIES, INC.

NOTE: This specimen label is for informational purposes only. All uses may not be approved in all states. See labeling which accompanied product for Directionsfor Use or call 800-777-8570 for more information. For automatic specimen label updates, register at www.wmmg.com.

WASP-FREEZE Wasp & Hornet Killer

®

Prescription Treatment brand®

Formula 1

Spray Downwards Spray Upwards

Return to Index...

NOTE: This specimen label is for informational purposes only. All uses may not be approved in all states. See labeling which accompanied product for Directionsfor Use or call 800-777-8570 for more information. For automatic specimen label updates, register at www.wmmg.com.

WASPS AND HORNETS: Hold container in upright position to treat. Stand safe distance,6 - 15 feet from nest and not directly underneath. Align actuator opening with themark on valve cup. Aim actuator openingtoward nest. Treat nest until thoroughly wet.Wasps and hornets on nest should be contactedwith spray when possible. Best time of day totreat is in evening or early morning, sincewasps and hornets congregate on or in nest atnight. Do not apply to pets or contaminatefood, foodstuffs, dishes or utensils. For outdoor use only.To prevent dying insects from falling on skinand clothing, avoid standing directly undernest being treated.YELLOWJACKETS AND BEES: Locateunderground nest. Align actuator openingdirectly opposite the mark on valve cup.Depress actuator and treat, with a sweepingmotion, any stimulated or stirred-up insectsaround nest opening. Afterwards, move forward to nest opening and apply liquid for 6 - 8 seconds directly into nest hole. This willsuffocate bees and yellowjackets in nest; other bees and yellowjackets trying to return tonest will be repelled and will fly around andaway harmlessly.

SPIDERS, INCLUDING BLACK WIDOWAND BROWN RECLUSE: Apply spraydirectly onto spiders and web.

STORAGE AND DISPOSALDo not contaminate water, food, or feed bystorage or disposal.STORAGE: Store in a cool area away fromheat or open flame.CONTAINER DISPOSAL: Do not punc-ture or incinerate! Empty container by using the product according to the label directions. Offer empty container for recycling, if available, or place in trash if allowed by state and local regulations. If container is partly full, contact your local solid waste agency orcall 1-800-CLEANUP for disposal instructions.

INDUSTRIAL SPECIFICATIONSFlash Point (TCC): 144°FDielectric (cup test with electrodes1/10" apart): No breakdown up to 49,300 volts.Arcing (spray test electrodes 12" apart):No arcing at 35,000 volts.Tested on Polyethylene, Polycarbonate,Noryl®, ABS-T and ABS-SB4500 plastics withno damage.

Contains no CFCs or other ozone depleting substances. Federal regulations prohibit CFC propellants in aerosols.

A Prescription Treatment® brand insecticide from:Whitmire Micro-Gen Research Laboratories, Inc.

3568 Tree Court Industrial Blvd.St. Louis MO 63122-6682

www.wmmg.com© 2007 Whitmire Micro-Gen Research Laboratories, Inc.

071213-22

WASP-FREEZE® Wasp & Hornet Killer Formula 1

SPECIMEN LA

BEL

ZP® Rodent Bait

KILLS RATS, MICE, AND GOPHERS

ACTIVE INGREDIENT: Zinc Phosphide (CAS #1314-84-7): …………….. 2% INERT INGREDIENTS:……………….…….. 98%

TOTAL 100%


FIRST AID Have label with you when obtaining treatment advice, including 1-877-854-2494.

Any persons applying zinc phosphide products and experiencing signs and symptoms such asnausea, abdominal pain, tightness in the chest, or weakness, should be seen by a physicianimmediately. If swallowed

* Call a poison control center or doctor immediately for treatment advice ortransport the patient to the nearest hospital.

* Do not drink water.* Do not administer anything by mouth or induce vomiting unless told to do so

by the poison control center or doctor.If on skin or clothing

* Take off contaminated clothing.* Rinse skin immediately with plenty of water for 15 – 20 minutes.* Call a poison control center or doctor immediately for treatment advice.

If inhaled

* Move person to fresh air.* If person is not breathing, call an ambulance, then give artificial respiration,

preferably mouth-to-mouth, if possible.* Call a poison control center or doctor immediately for treatment advice.

If in eyes * Hold eye open and rinse slowly and gently with water for 15 to 20 minutes.* Remove contact lenses, if present, after the first 5 minutes, then continue

rinsing eye.* Call a poison control center or doctor immediately for treatment advice.

See Back/Side Panel for First Aid and additional precautionary statements.

Manufactured by: Bell Laboratories, Inc. Madison, WI 53704 U.S.A.

EPA REG. NO. 12455-18 EPA EST. NO. 12455-WI-1

__________________________________________________________________ This Section For Product Label Identification Purposes Only:

ZP Rodent Bait, EPA Reg. No. 12455-18, Container Label Page 1 of 4

Return to Index...

SPECIMEN LA

BEL



DIRECTIONS FOR USE

It is a violation of Federal law to use this product in a manner inconsistent with its labeling. READ THIS LABEL: Read this entire label and follow all use directions and use precautions. Use only for sites, pests, and application methods described on this label. IMPORTANT: Do not expose children, pets, or other nontarget animals to rodenticides. To help prevent accidents: 1. Store product not in use in a location out of reach of children and pets. 2. Apply bait in locations out of reach of children, pets, domestic animals and nontarget wildlife,

or in tamper-resistant bait stations. These stations must be resistant to destruction by dogs and by children under six years of age, and must be used in a manner that prevents such children from reaching into bait compartments and obtaining bait. If bait can be shaken from bait stations when they are lifted, units must be secured or otherwise immobilized. Even stronger bait stations are needed in areas open to hoofed livestock, raccoons, bears, other potentially destructive animals, or in areas prone to vandalism.

3. Apply bait used to control pocket gophers directly into their underground tunnels. 4. Dispose of product container, and unused, spoiled, and unconsumed bait as specified on this

label.

RATS AND MICE USE RESTRICTIONS: Use against the Norway rat, Roof rat and the House mouse in and around homes, industrial, agricultural and commercial buildings, and similar man-made structures. Do not place in areas where there is a possibility of contaminating food or surfaces that come in direct contact with food. When used in USDA-inspected facilities, this product must be applied in tamper-resistant bait stations. SELECTION OF TREATMENT AREAS: After removing as much food, water and harborage as possible, determine dry, acid-free areas where rats and mice will most likely find and consume the bait. Generally these areas are along walls, by gnawed openings, in or beside burrows, in corners and concealed places, between floors and walls, or in locations where rats and mice or their signs have been observed. APPLICATION DIRECTIONS FOR RATS: Apply 1 to 2 teaspoon amounts of bait per placement. For outdoor use, place bait in active rat burrows or tamper-resistant bait stations. Maintain an uninterrupted supply of fresh bait until all signs of feeding have stopped. Do not treat the same area at less than 30 day intervals. APPLICATION DIRECTIONS FOR MICE: Apply 1 teaspoon of bait per placement at 8 to 12 foot intervals. For outdoor use, place bait in tamper-resistant bait stations. Maintain an uninterrupted supply of fresh bait until all signs of feeding have stopped. Do not treat the same area at less than 30 day intervals. Collect and dispose of all dead animals and excess bait properly.

POCKET GOPHERS* USE RESTRICTIONS: Use against pocket gophers in rangeland and cropland (grain fields, forage crops, hay and alfalfa crops and vegetable crops). May also be used in forest areas, parks, nurseries, lawns, golf courses, around homes, and other noncrop areas. Only apply the bait underground. Collect and bury all dead animals found above the ground.

SPECIMEN LA

BEL



APPLICATION DIRECTIONS FOR POCKET GOPHERS: Use one of the following baiting methods for controlling pocket gophers. Plug Removal Baiting: Burrowing pocket gophers (Thomomys spp. and Geomys spp.) throw out low, fan shaped mounds on either side of their underground tunnel. These lateral tunnels coming to the surface are on the flat side of the fan and are plugged with soil. Using a long-handled spoon, carefully remove the plug. Insert one teaspoon of bait as far down as possible. Reclose opening, being careful not to cover bait with soil. Main Runway Baiting: To locate main runways, probe about 6 to 8 inches away from mounds by use of an iron bar, a strong stick, or other suitable implement. Resistance on probe will drop suddenly and probe will fall about two inches when main runway is entered. Carefully enlarge the opening to accommodate insertion of the bait. Insert one teaspoon of bait into each active tunnel. Carefully close the hole with a stone, sod, or soil. Take care not to cover bait with soil. Burrow Builder: Drop a teaspoon quantity of bait at 4-5 foot intervals in the artificial burrow made by the machine. * Not for pocket gopher use in NC

PRECAUTIONARY STATEMENTS HAZARDS TO HUMANS AND DOMESTIC ANIMALS

Keep away from humans, domestic animals and pets. Harmful if swallowed, absorbed through the skin, inhaled, or in eyes. Do not breathe dust. If bait is handled, wear gloves. Wash hands thoroughly after applying bait and before eating, drinking, chewing gum, using tobacco or using the toilet. Avoid contamination of feed or foodstuffs. Avoid contact with acids. Wash all utensils, spoons, or measuring devices thoroughly after using.

ENVIRONMENTAL HAZARDS This product is toxic to fish, birds and other wildlife. Do not apply this product directly to water or to areas where surface water is present or to intertidal areas below the mean high water mark.

STORAGE AND DISPOSAL Do not contaminate water, food or feed by storage or disposal. STORAGE: Store only in original container in a cool, dry place inaccessible to children and pets. Keep containers closed and away from other chemicals. PESTICIDE DISPOSAL: Wastes resulting from the use of this product may be placed in trash or delivered to an approved waste disposal facility. PESTICIDE CONTAINER: Do not reuse empty container. Dispose of empty container by placing in trash, at an approved waste disposal facility or by incineration or, if allowed by state and local authorities, by burning. If burned stay out of smoke. Call your Local Waste Agency for any questions on proper disposal. WARRANTY: To the extent consistent with applicable law, seller makes no warranty, expressed or implied, concerning the use of this product other than indicated on the label. Buyer assumes all risk of use and/or handling of this material when such use and/or handling is contrary to label instructions

SPECIMEN LA

BEL



Alternate Environmental Hazards Language for packaging intended solely for consumer use (< 1 lb.)

ENVIRONMENTAL HAZARDS This product is toxic to fish, birds and other wildlife. Do not apply directly to water. Alternate Storage and Disposal Language for packaging solely for consumer use (< 1 lb.)

STORAGE AND DISPOSAL STORAGE: Store only in original container in a cool, dry place inaccessible to children and pets. Keep containers closed and away from other chemicals. DISPOSAL: If empty: do not reuse this container. Place in trash or offer for recycling if available. If partially filled: Place in trash or call your local solid waste agency for disposal instructions. Never place unused product down any indoor or outdoor drain. 091007

DIR

EC

TIO

NS

FOR

USE

It is

a v

iola

tion

of F

eder

al la

w to

use

this

pro

duct

in a

man

ner

inco

nsis

tent

with

its l

abel

ing.

RE

AD

TH

IS L

AB

EL

: R

ead

this

ent

ire la

bel a

nd f

ollo

w a

llus

e di

rect

ions

and

use

pre

caut

ions

.IM

POR

TA

NT

: D

o no

t ex

pose

ch

ildre

n,

pets

, or

ot

her

nont

arge

t ani

mal

s to

rode

ntic

ides

. To

hel

p pr

even

t acc

iden

ts:

1.

Stor

e pr

oduc

t no

t in

use

in

a lo

catio

n ou

t of

rea

ch o

fch

ildre

n an

d pe

ts.

2.

App

ly b

ait u

sed

to c

ontro

l rat

s an

d m

ice

in lo

catio

ns o

utof

re

ach

of

child

ren,

pe

ts,

dom

estic

an

imal

s an

dno

ntar

get

wild

life,

or

in t

ampe

r-re

sist

ant

bait

stat

ions

.Th

ese

stat

ions

mus

t be

resi

stan

t to

dest

ruct

ion

by d

ogs

and

by c

hild

ren

unde

r si

x ye

ars

of a

ge,

and

mus

t be

used

in

a m

anne

r th

at p

reve

nts

such

chi

ldre

n fr

omre

achi

ng in

to b

ait c

ompa

rtmen

ts a

nd o

btai

ning

bai

t. I

fba

it ca

n be

sha

ken

from

bai

t st

atio

ns w

hen

they

are

lifte

d, u

nits

mus

t be

secu

red

or o

ther

wis

e im

mob

ilize

d.Ev

en s

trong

er b

ait s

tatio

ns a

re n

eede

d in

are

as o

pen

toho

ofed

liv

esto

ck,

racc

oons

, be

ars,

othe

r po

tent

ially

dest

ruct

ive

anim

als,

or in

are

as p

rone

to v

anda

lism

.3.

A

pply

bai

t use

d to

con

trol p

ocke

t gop

hers

dire

ctly

into

thei

r und

ergr

ound

tunn

els.

4.

Dis

pose

of

prod

uct c

onta

iner

, and

unu

sed,

spo

iled,

and

unco

nsum

ed b

ait a

s spe

cifie

d on

this

labe

l.

RA

TS

AN

D M

ICE

USE

RE

STR

ICT

ION

S: U

se a

gain

st t

he N

orw

ay r

at,

Roo

fra

t an

d th

e H

ouse

mou

se i

n an

d ar

ound

hom

es,

indu

stria

l,ag

ricul

tura

l and

com

mer

cial

bui

ldin

gs, a

nd s

imila

r man

-mad

est

ruct

ures

. Do

not p

lace

Pla

ce P

acs

in a

reas

whe

re th

ere

is a

poss

ibili

ty o

f co

ntam

inat

ing

food

or

surf

aces

tha

t co

me

indi

rect

con

tact

with

foo

d. W

hen

used

in

USD

A-in

spec

ted

faci

litie

s, th

is p

rodu

ct m

ust b

e ap

plie

d in

tam

per-

resi

stan

t bai

tst

atio

ns.

SEL

EC

TIO

N O

F T

RE

AT

ME

NT

AR

EA

S: A

fter r

emov

ing

as m

uch

food

, w

ater

and

har

bora

ge a

s po

ssib

le,

dete

rmin

edr

y, a

cid-

free

are

as w

here

rats

and

mic

e w

ill m

ost l

ikel

y fin

dan

d co

nsum

e th

e ba

it. G

ener

ally

thes

e ar

eas

are

alon

g w

alls

,by

gna

wed

ope

ning

s, in

or

besi

de b

urro

ws,

in c

orne

rs a

ndco

ncea

led

plac

es,

betw

een

floor

s an

d w

alls

, or

in

loca

tions

whe

re ra

ts a

nd m

ice

or th

eir s

igns

hav

e be

en o

bser

ved.

APP

LIC

AT

ION

D

IRE

CT

ION

S FO

R

RA

TS:

A

pply

1

Plac

e Pa

c (u

sual

ly

at

inte

rval

s of

15

to

30

fe

et)

per

plac

emen

t. F

or o

utdo

or u

se, p

lace

bai

t in

activ

e ra

t bur

row

sor

tam

per-

resi

stan

t ba

it st

atio

ns.

Mai

ntai

n an

uni

nter

rupt

edsu

pply

of

fres

h ba

it un

til a

ll si

gns

of f

eedi

ng h

ave

stop

ped.

Do

not t

reat

the

sam

e ar

ea w

ith P

lace

Pac

s at l

ess t

han

30 d

ayin

terv

als.

APP

LIC

AT

ION

DIR

EC

TIO

NS

FOR

MIC

E: A

pply

1Pl

ace

Pac

per p

lace

men

t at 8

to 1

2 fo

ot in

terv

als.

For o

utdo

orus

e, p

lace

bai

t in

tam

per-

resi

stan

t bai

t sta

tions

. Mai

ntai

n an

unin

terr

upte

d su

pply

of f

resh

bai

t unt

il al

l sig

ns o

f fee

ding

have

stop

ped.

Do

not t

reat

the

sam

e ar

ea w

ith P

lace

Pac

s at

less

than

30

day

inte

rval

s. C

olle

ct a

nd d

ispo

se o

f all

dead

anim

als a

nd e

xces

s bai

t pro

perly

.

* N

ot fo

r poc

ket g

ophe

r use

in N

C

DIR

ECTI

ON

S FO

R U

SE (C

ontin

ued

from

oth

er p

anel

)A

PPLI

CA

TIO

N D

IREC

TIO

NS

(Con

tinue

d fr

om o

ther

pan

el)

POC

KE

T G

OPH

ER

S*U

SE

RE

STR

ICT

ION

S:

Use

ag

ains

t po

cket

go

pher

s in

rang

elan

d an

d cr

opla

nd (

grai

n fie

lds,

fora

ge c

rops

, ha

y an

dal

falfa

cro

ps a

nd v

eget

able

cro

ps).

May

als

o be

use

d in

for

est

area

s, pa

rks,

nurs

erie

s, la

wns

, gol

f co

urse

s, ar

ound

hom

es, a

ndot

her n

oncr

op a

reas

. O

nly

appl

y th

e ba

it un

derg

roun

d. C

olle

ctan

d bu

ry a

ll de

ad a

nim

als f

ound

abo

ve th

e gr

ound

.A

PPL

ICA

TIO

N

DIR

EC

TIO

NS

FOR

PO

CK

ET

GO

PHE

RS*

: U

se o

ne o

f th

e fo

llow

ing

baiti

ng m

etho

ds f

orco

ntro

lling

poc

ket g

ophe

rs.

PLU

G R

EM

OV

AL

BA

ITIN

G:

Bur

row

ing

pock

et g

ophe

rs(T

hom

omys

spp

. and

Geo

mys

spp

.) th

row

out

low

, fan

sha

ped

mou

nds

on e

ither

sid

e of

the

ir un

derg

roun

d tu

nnel

. T

hese

late

ral t

unne

ls c

omin

g to

the

surf

ace

are

on th

e fla

t sid

e of

the

fan

and

are

plug

ged

with

soi

l. U

sing

a l

ong-

hand

led

spoo

nca

refu

lly r

emov

e th

e pl

ug.

Inse

rt a

Plac

e Pa

c as

far

dow

n as

poss

ible

. R

eclo

se o

peni

ng, b

eing

car

eful

not

to c

over

bai

t with

soil.

MA

IN R

UN

WA

Y B

AIT

ING

: To

loca

te m

ain

runw

ays,

prob

eab

out 6

to 8

inch

es a

way

from

mou

nds

by u

se o

f an

iron

bar,

ast

rong

stic

k, o

r ot

her

suita

ble

impl

emen

t. R

esis

tanc

e on

pro

bew

ill d

rop

sudd

enly

and

pro

be w

ill f

all

abou

t tw

o in

ches

whe

nm

ain

runw

ay i

s en

tere

d.

Car

eful

ly e

nlar

ge t

he o

peni

ng t

oac

com

mod

ate

inse

rtion

of t

he b

ait p

acke

t. In

sert

one

Plac

e Pa

cin

to e

ach

activ

e tu

nnel

. C

aref

ully

clo

se th

e ho

le w

ith a

sto

ne,

sod,

or s

oil.

Tak

e ca

re n

ot to

cov

er b

ait w

ith so

il.

PRE

CA

UT

ION

AR

Y S

TA

TE

ME

NT

SH

azar

ds to

Hum

ans a

nd D

omes

tic A

nim

als

Kee

p aw

ay fr

om h

uman

s, do

mes

tic a

nim

als a

nd p

ets.

Har

mfu

l if

swal

low

ed. D

o no

t br

eath

e du

st. W

ash

hand

s th

orou

ghly

afte

rap

plyi

ng b

ait a

nd b

efor

e ea

ting,

drin

king

, che

win

g gu

m, u

sing

toba

cco

or u

sing

the

toi

let.

Avo

id c

onta

min

atio

n of

fee

d or

food

stuf

fs. A

void

con

tact

with

aci

ds. W

ash

all u

tens

ils, s

poon

s,or

mea

surin

g de

vice

s tho

roug

hly

afte

r usi

ng.

EN

VIR

ON

ME

NT

AL

HA

ZA

RD

STh

is p

rodu

ct i

s to

xic

to f

ish,

bird

s an

d ot

her

wild

life.

Do

not

appl

y th

is p

rodu

ct d

irect

ly t

o w

ater

or

to a

reas

whe

re s

urfa

cew

ater

is p

rese

nt o

r to

inte

rtida

l are

as b

elow

the

mea

n hi

gh w

ater

mar

k.

STO

RA

GE

AN

D D

ISPO

SAL

Do

not c

onta

min

ate

wat

er, f

ood

or fe

ed b

y st

orag

e or

dis

posa

l.ST

OR

AG

E: S

tore

onl

y in

orig

inal

con

tain

er in

a c

ool,

dry

plac

ein

acce

ssib

le t

o ch

ildre

n an

d pe

ts.

Kee

p co

ntai

ners

clo

sed

and

away

from

oth

er c

hem

ical

s.D

ISPO

SAL

: If

em

pty:

do

not

reus

e th

is c

onta

iner

. Pl

ace

intra

sh o

r off

er fo

r rec

yclin

g if

avai

labl

e. If

par

tially

fille

d: P

lace

in t

rash

or

call

your

loc

al s

olid

was

te a

genc

y fo

r di

spos

alin

stru

ctio

ns.

Nev

er p

lace

unu

sed

prod

uct

dow

n an

y in

door

or

outd

oor d

rain

.

WA

RR

AN

TY

: Sel

ler m

akes

no

war

rant

y, e

xpre

ssed

or i

mpl

ied,

conc

erni

ng t

he u

se o

f th

is p

rodu

ct o

ther

tha

n in

dica

ted

on t

hela

bel.

Buy

er a

ssum

es a

ll ris

k of

use

and

/or

hand

ling

of t

his

mat

eria

l w

hen

such

use

and

/or

hand

ling

is c

ontra

ry t

o la

bel

inst

ruct

ions

.11

1305

ZP® R

oden

t Bai

tPl

ace

Pacs

KIL

LS R

ATS,

MIC

E AN

D G

OPH

ERS*

AC

TIV

E IN

GR

EDIE

NT:

Zinc

Pho

sphi

de (C

AS

#131

4-84

-7)

……

……

…..

2%IN

ERT

ING

RED

IEN

TS:…

……

……

….…

…..

9

8% T

OTA

L

1

00%

KE

EP

OU

T O

F R

EA

CH

OF

CH

ILD

RE

NC

AU

TIO

N

FIR

ST A

IDH

ave

labe

l with

you

whe

n ob

tain

ing

treat

men

t adv

ice,

incl

udin

g 1-

877-

854-

2494

.

Any

per

sons

app

lyin

g zi

nc p

hosp

hide

pro

duct

s and

exp

erie

ncin

g si

gns a

nd sy

mpt

oms

such

as n

ause

a, a

bdom

inal

pai

n, ti

ghtn

ess i

n th

e ch

est,

or w

eakn

ess,

shou

ld b

e se

en b

ya

phys

icia

n im

med

iate

ly.

If swal

low

ed*

Cal

l a p

oiso

n co

ntro

l cen

ter o

r doc

tor i

mm

edia

tely

for t

reat

men

t adv

ice

or tr

ansp

ort t

he p

atie

nt to

the

near

est h

ospi

tal.

* D

o no

t drin

k w

ater

.*

Do

not a

dmin

iste

r any

thin

g by

mou

th o

r ind

uce

vom

iting

unl

ess t

old

todo

so b

y th

e po

ison

con

trol c

ente

r or d

octo

r.If

on

skin

or c

loth

ing

* W

ash

with

ple

nty

of so

ap a

nd w

ater

.

If inha

led

* M

ove

pers

on to

fres

h ai

r.*

If

pers

on i

s no

t br

eath

ing,

cal

l an

am

bula

nce,

the

n gi

ve a

rtific

ial

resp

iratio

n, p

refe

rabl

y m

outh

-to-m

outh

, if p

ossi

ble.

* C

all

a po

ison

con

trol

cent

er o

r do

ctor

im

med

iate

ly f

or t

reat

men

tad

vice

.

NE

T C

ON

TE

NT

S: 1

00 x

7.5

g P

lace

Pac

s

Man

ufac

ture

d by

:

Bel

l Lab

orat

orie

s, In

c.M

adis

on, W

I 537

04 U

.S.A

.

EPA

REG

. NO

. 124

55-5

9 EP

A E

ST. N

O.

1245

5-W

I-1

april 1, 2016 - pestgon.compestgon.com/pdf/sds/4_2016_master labels.pdf · invict xpress granular...

Documents