approval sheet description : 16 x ccd color camera set model no. : onz - an101 /151/102/152 ( ntsc)...

APPROVAL SHEETAPPROVAL SHEET

DESCRIPTION : 16 X CCD COLOR CAMERA

SET MODEL NO. : ONZ - AN101 /151/102/152 ( NTSC) ONZ - AP101 /151/102/152 ( PAL )

ISSUED

CHECKED

APPROVED

DATE : 11. Jul. ‘00REVISION No. 1.0MESSRS.

Receipt Stamp

ONIX SYSTEM INC.

4 FLOOR, KUNAM B/D, 5- 4, YANGJAE- DONG, SEOCHO- KU, SEOUL, 137- 130, KOREA

TEL: 82- 2- 596- 0144/ 82- 2- 573- 0144TEL: 82- 19- 310- 2213FAX : 82- 2- 596- 0143URL:http://www.globalsources.com/onix.coURL:http://www.onix.co.kr E- mail:[email protected]

ONZ-AN101/151/102/152, AP101/151/102/152 Specifications

ONIX SYSTEM INC.

CCD COLOR CAMERA SPECIFICATIONS

ONZ - AN101, 151, AP101, 151 : Control through RS-232 Signal ( TTL Level )

ONZ - AN102, 152 AP102, 152 : Control through RS-422/485 Signal

CONTENTS

1/11

1. SPECIFICATIONS------------------------------------------------------------ 2

2. MEASUREMENT SPECIFICATIONS------------------------------------ 4

3. EXTERNAL CONTROL SPECIFICATIONS---------------------------- 4

4. ENVIRONMENT CONDITION AND TEST----------------------------- 5

5. LAYOUT OF PLUG --------------------------------------------------------- 5

6. INTERFACE (RS-232C)---------------------------------------------------- 6 7. INTERFACE(RS-422/485) ------------------------------------------------- 7 8. RECOMMENDED CIRCUIT FOR LOCAL CONTROLS ----------- 8

9. LENS TEST CONDITION-------------------------------------------------- 9

9. APPEARANCE--------------------------------------------------------------- 10

10.PACKING METHOD-------------------------------------------------------- 11

PAGE


ONIX SYSTEM INC.

1. SPECIFICATIONS

Signal System NTSC ( ONZ - AN101/102 ) PAL ( ONZ - AP101/102 )

Scanning System 2 : 1 Interlace

Scanning Frequency ( H ) 15.734 KHz 15.625 KHz

59.94 Hz 50 Hz

Image Sensor 1 / 4 Inch Solid State Interline CCD Image Sensor

Total Pixels No.

Effective Pixels No.

Scanning Frequency ( V )

REMARKS

811 (H) X 508 (V) 410K 795 (H) X 596 (V) 470K

768 (H) X 494 (V) 380K 752 (H) X 582 (V) 440K

Signal System NTSC ( ONZ - AN151/152 ) PAL ( ONZ - AP151/152 )

Scanning System 2 : 1 Interlace

Scanning Frequency ( H ) 15.734 KHz 15.625 KHz

59.94 Hz 50 Hz

Image Sensor 1 / 4 Inch Solid State Interline CCD Image Sensor

Total Pixels No.

Effective Pixels No.

Scanning Frequency ( V )

REMARKS

537 (H) X 505 (V) 270K 537 (H) X 597 (V) 320K

510 (H) X 492 (V) 250K 500 (H) X 582 (V) 290K

1) Lens F1.4 ~ 2.8 , f = 4.0 ~ 64.0 mm , x16 Zoom Video Auto Focus

Angle of View H : 47 。 (WIDE) , 3 。 (TELE)

High Durability Zoom Lens

a) Zoom Durability More than 500k at Room Temperature ( See Page. 6. )

b) Focus Durability More than 500k at Room Temperature ( See Page. 6. )

c) Iris Durability More than 500k at Room Temperature ( See Page. 6. )

2) Focus Length ∞ ~ 1.0m (Tele) ~ 0.01m (Wide)

3) Signal Process Digital Signal Process

4) Sync System(Auto) Internal / External sync ( Line Lock)

5) Camera Function Control through RS-232 Signal ( TTL Level ) : CNB-AN101,151,AP101,151 Control through RS-422/485 Signal : CNB-AN102,152,AP102,152

a) Optical Zoom TELE ~ WIDE (Zoom Speed : 3.6 sec / 6 sec )

b) Digital Zoom Off / On ( ~ 8 times )

c) Video Focus Auto / Manual ( NEAR ~ FAR ) / Push Auto

(a) Manual Mode

Zoom Start Zoom Stop

Manual Manual ( AF Action is activated for a moment before focus stops )

“ Bold : Default Mode ”

2/11


ONIX SYSTEM INC.

d) White Balance Auto / Indoor / Outdoor / Push Auto / Manual ( R&B Gain Level UP/Down ) Special ( R or B Gain Level Control )

e) Shutter Speed Auto/ Manual (1/60 ~ 1/ 10000 ( NTSC) / 1/50 ~ 1/10000 (PAL) )

f) Iris Control Auto / Manual ( Manual Iris Level : UP ~ Down) g) Gain Control Auto / Manual ( Auto Gain Control : UP ~ Down)

h) Sharpness Manual ( Sharpness UP ~ Down )

i) Brightness Manual ( Brightness UD ~ Down )

j) Negative Off / On ( Negative Level UP ~ DOWN )

k) OSD Function On / Off (See an Annexed Document “ APPENDIX 1 ” )

l) Flickerless Off / On ( 1 / 100 sec Shutter Set (NTSC) / 1 / 120 sec Shutter Set (PAL) )

m) Back Light Off / On/ Auto

n) Position Preset 64 Mode Set / Move ( Store with Internal EEPROM )

(a) Zoom Trace Preset Mode : MF Trace

* In case of memory ( EX. Memory Point : )

WIDE TELE×1 ×16 ×32(Opt.) (Digi.)

3.6 sec 1 sec

(b) Zoom Trace Preset Mode : MF NO-Trace

* In case of preset

WIDE TELE×1 ×16 ×32(Opt.) (Digi.)

1.6 sec Instant

6) Video Output Level

NTSC

Video Level

Sync Level

0.714 ± 0.07V ( 100 ± 10 IRE)

0.286 ± 0.035V ( 40 ± 10 IRE)

Burst Level 0.286 ± 0.035V ( 40 ± 10 IRE)

700 ± 70 mV

300 ± 35 mV

300 ± 35 mV

PAL

Video Level

Sync Level

Burst Level

3/11


ONIX SYSTEM INC.

7) Color Reproduction

NTSCAmplitude ( % )

Phase ( 。 )

100 %(Base)

180 。 (Base)

RED BLUE YELLOW BURSTCOLOR

200 ± 40 %

103 ± 20 。

PALAmplitude ( % )

Phase ( 。 )

100 %(Base)

135 。 (Base)

130 ± 40 %

345 ± 20 。 115 ± 40 %

170 ± 20 。 200 ± 40 %

103 ± 20 。 130 ± 40 %

345 ± 20 。 115 ± 40 %

170 ± 20 。

8) Horizontal Resolution More than 480 Lines ( High Resolution ) More than 380 Lines ( Normal Resolution )

9) Luminance S/N More than 48 dB

10) Sensitivity Typ. 1Lux ---- At signal Level 30 IRE

( LENS-F : F = 1.4 ( WIDE ) AGC Gain : Max

11) Supplied Voltage 9.0 V ~ 15.0 V ( Recommendation 12.0 V ± 0.5 V )

12) Supplied Current 210 mA ( Steady-state )

350 mA ( Max ) ----- Under the zooming and focusing Operation

13) Power consumption 4.3 W (Max)

14) Dimensions 58.0(W) × 59.8 (H) × 101.2(D) mm ( Except Connector )

15) Weight 330 g ( Approx. )

16) Appearance / Dimensions See Attached Page 10.

17) Body Color Black

18) Packing Method See Attached Page 11.

19) Optional Accessories

2. MEASUREMENT SPECIFICATIONS

* Standard Measurement Condition and Measurement Procedure

See an Annexed Document “ APPENDIX 2 ”

3. EXTERNAL CONTROL SPECIFICATIONS

* External Control Using RS-232C ( Command List )

See an Annexed Document “ APPENDIX 3 ”

4/11


ONIX SYSTEM INC.

1) Operating Condition Temperature -10 。 C ~ 50 。 C ( Recommendation : -5 。 C ~ 40 。 C )

Humidity 10 % 85 %∼

2) Storage Condition Temperature -20 。 C ~ 60 。 C Humidity 0 % 90 %∼

3) High Temperature storage Test

Leaving the packed at Temperature of 60 。 C for 72 Hours, and then after leaving it at

Normal Temperature for 8 Hours, there should be no Problem in Performance.

4) Low Temperature storage Test

Leaving the packed at Temperature of -20 。 C for 72 Hours, and then after leaving it at

Normal Temperature for 8 Hours, there should be no Problem in Performance.

4. ENVIRONMENT CONDITION AND TEST

5/11

5. LAYOUT OF PLUG ( REAR PANNEL)

-+DC 12V

TELE(+)

(-)WIDE

BLC(SET)

MENU

VIDEO OUT

CONTROL

POWER INClass 2 Only


ONIX SYSTEM INC.

6. INTERFACE ( RS -232C TTL : ONZ-AN101,151,AP101,151 )

1-1) Pin Assignment ( 6 Pin Circle Connector )

Key

NAMEPIN No.

1

2

3

4

5

6

I/O

Input

Note

Input

1) Pin Diagram ( 6 Pin Circle Connector ) : Rear View

W

1

2 5

3

6

4

GND

Output

Input Green

White

Brown

Yellow

Black

Red

* is the color of the cable. ( If it offered )

GND

* Color

RD(For RS-232C)

TD(For RS- 232C) CMOS Level 5V ( Low : Max 0.8V , High : Min 3.7V )

CMOS Level 5V ( Low : Max 0.8V , High : Min 3.7V )

Line IN EX. FV ( Negative. 5 Vp-p )

1

2

3

4

5

6

7

8

9

1. Frame GND2. RD3. TD4. DTR5. Signal GND6. DSR7. RTS8. CTS9. RI

A) RS-232C D-Sub Connector

2) PC Interface

RD 1

TD 2

6/11

NAME


ONIX SYSTEM INC.

7. INTERFACE (RS - 422/485 : ONZ-AN102,152,AP102,152 )

1-1) Pin Assignment ( 6 Pin Circle Connector )

T+

NAMEPIN No.

1

2

3

4

5

6

I/O

Input

Note

1) Pin Diagram ( 6 Pin Circle Connector ) : Rear View

W

1

2 5

3

6

4

GND

Output

Input Green

White

Brown

Yellow

Black

Red

* is the color of the cable. ( If it offered )

T -

* Color

R+

R -

)

Line IN EX. FV ( Negative. 5 Vp-p )

2) PC Interface ( RS-422 Communication)

Input

Output

R + 1

R - 2

T + 3

T - 4

Tx+

Tx-

Rx-

Rx+

TD

RD

A) RS-232C TO RS-422 Converter

1. Frame GND2. RD3. TD4. DTR5. Signal GND6. DSR7. RTS8. CTS9. RI

1

2

3

4

5

6

7

8

9

B) RS-232C D-Sub Connector

7/11

NAME


ONIX SYSTEM INC.

2) Line In Pulse ( EX. FV)

Min : 200 nsec

60 Hz ± 0.25 Hz ( NTSC )

50 Hz ± 0.25 Hz ( PAL)

5 V

0 V

A) Pulse- Signal Spec of EX.FV

1) KEY Function(CNB-AN101/151/AP101/151)

8. RECOMMENDED CIRCUIT FOR LOCAL CONTROLS

8/11

POWERON/OFF

6.8K 8.2K 12K 18K 33K 68K 180K

TELE(+)

0.01uFKEY 3

MENU WIDE(-) A/MPUSH AUTO

NEGAON/OFF

NEAR(+) FAR(-)

: WIRE REMOTE CONTROL KEY FUNCTION


ONIX SYSTEM INC.9/11

9. LENS TEST CONDITION

1) Zoom

2) Focus

1.5sec

1 Cycle

3 ) Auto Iris

1.5sec

3 sec

TELE

WIDE 1 sec pause

1 Cycle

NEAR

FAR1V pause

1V pause

1V

1 Cycle

OPEN

CLOSE

RESET


ONIX SYSTEM INC.

10. APPEARANCE

10/11

46

1 4.

VID

MO

O

=

E

FO

UAO

TO

SUCf 4.0

~04. 6

m

:1

m

CITP

61LAX RWPO E

OZ

SER

. N

o.

MO

DEL

NO

.M

AD

E IN

KO

REA


ONIX SYSTEM INC.

11. PACKING METHOD

11/11

DESC.

10

9

7

8

NO

6

QT'Y

TAPE

BOX INNER ASSEMBLY

BOX, MASTER CARTON

PAD

LABEL SHIPPING

0.005

1.0

1/12

1/12

2/12

PACKING, MAIN

BOX, INNER

SET

LABEL, SERIAL No.

DESC.

5

4

2

3

NO

1

1.0

2.0

1.0

QT'Y1.0

MANUAL 1.0

2

3

4

3

5

1

BOX INNER ASSEMBLY

APPENDIX 1

ONZ - AN101 /151/102/152 ( NTSC) ONZ - AN101 /151/102/152 ( PAL)

DATE : 11. Jul. ‘00REVISION No. 1.0

MODEL :

OSD(On Screen Display)

ONIX SYSTEM INC.


ONIX SYSTEM INC.

1. OSD(On Screen Display ) FORMAT

<Fig. 1 OSD DISPLAY POSITION>2) DESCRIPTION

1

OSD Format DESCRIPTION REMARKS

2

FUNCTION

Focus ModeNon display Focus Auto Mode

Focus Manual Mode

Mirror ModeMirror Mode Off

1) OSD DISPLAY POSITION

Non display

X10000 ID 255

WAIT

W T X32

1 2 3 4 5 6

7

8

Mirror Mode On

3

Back LightBack Light OFF

Back Light ON

Non display

4

Non display White Balance AUTO

WBC MODE

Push Auto White Balance:In this mode “Push Key” pressed,the white point traced automatically(PWB Auto Mode),“Push key” released, the white point preserved currently (PWB Manual Mode).

A Auto Back Light ON

1/5


ONIX SYSTEM INC.

* The OSDs of 1,2,3,4,5,7,8 disappear 5 sec later . But 6 can be displayed continuously by ID On/Off Key Action ( controlled by PC command Key).

OSD Format DESCRIPTION REMARKSFUNCTION

5 Shutter Speed

Normal Shutter ( NTSC:1 / 60 PAL:1 / 50 )

1 / 125 . . . .

1 / 1 0 0 0 0

28 variable steps.(Can be set to 8 steps by manufactureOption)

Non display

6 CAMERA IDAfter input the Identification Number to each camera ,Multi-point control is available (PC Control )( 000 255 ) . ∼

7 WAIT MODE WAITIndicates the camera stand-by modeuntil the camera power turns ON .

8

ZOOM DISPLAY

W

W

T X10

T X20

; In case of 16X Zoom; Optical Zoom only mode ; (Current Zoom :10X)

; In case of 32X Zoom ; Digital Zoom 2X mode ; (Current Zoom : 20X)

W T X100

; In case of 128X Zoom ;Digital Zoom 8X mode ; (Current Zoom : 100X )

Sharpness Adjustment Mode DISPLAY

BrightnessAdjustmentModeDISPLAY

X10

X34

2/5


ONIX SYSTEM INC.

2. MENU DESCRIPTIONS ( ENGLISH )

1) MENU FORMAT

<Fig2. MENU FORMAT>

MENU 1 IMAGE MIRROR OFF (ON) 2 NEG / POS POS (NEG) 3 COLOR ON (OFF) 4 WB CONTROL AUTO (PUSH AUTO) 5 SHUTTER 1/10000 6 CAMERA ID 123

MENU

7 ZOOM START X1 8 ZOOM STOP X128 9 BRIGHTNESS 2410 SHARPNESS 1011 FOCUS AUTO (PUSH AUTO)12 INIT SET OFF (ON) END

TELE BLC

WIDE MENU

(+)

(-)

(SET)

<Fig3. REAR PANNEL>

3/5


ONIX SYSTEM INC.

3 ) MENU DESCRIPTION

(1) IMAGE MIRROR When IMAGE MIRROR is ON state , The image displays in the opposite direction.

(3) COLOR ON : Color Mode , OFF : B / W (Monochrome Mode).

(2) NEG/POS Use to change NEGATIVE and POSITIVE mode . ON : Negative Mode , OFF : Positive Mode .

(7) ZOOM START Wide Zooming Area Start point allocation (1 ~128).

(4) WB CONTROL Use to change White Balance Mode. - AUTO : WB Range 2800 。 K 8000 ∼ 。 K . - PUSH AUTO : In this Mode you can adjust White point by using PUSH AUTO Key. (5) SHUTTER Use to change the Shutter Speed . At this time , AE mode acts automatically ( 28/8 steps control is available ).

(6) CAMERA ID Each Identification number can be assigned to each camera. And ID NOs can be displayed on Monitor to confirm each camera. ( 000 ~ 255 : total numbers of ID are 256 ) .

(8) ZOOM STOP Tele Zooming Area End point allocation (1 ~128).

(9) BRIGHTNESS Use to change the brightness level of scene ( 0 ~ 48 ). (10) SHARPNESS Use to change the contour of scene ( 0 ~ 15 ) .

(11) FOCUS Use to change Focus Mode . - AUTO : Focusing acts Automatically - MANUAL : Focusing is controlled by Far and Near Keys . - PUSH AUTO : Auto Focusing is activated for a moment (when Push Auto Key is pressed) and stops.

(12) INIT SET Turn the initial mode ON , the changed data are renewed to manufacturer settings. (The data are initialized to its shipping condition )

2) Using MENU (1) Menu Mode : In order to display the MENU on the screen , Press the MENU key . If you keep pressing MENU over 2 seconds, OSD will be off.

Menu mode will be displayed again once Menu is pressed.

(2) Menu Item selection Mode: Position Hand Mark to each ITEM you want to change by using Wide and Tele Keys . Press the BLC(SET) button. (3) Menu Data Change Mode: Press the TELE and WIDE key .Then the right side of selected ITEM will blink and the values can be changed by using Tele and Wide keys . Press the BLC(SET) button. (4) Press the BLC(SET) key again to return to Mode(2). (5) To escape from Menu Mode, Press Menu key again in Mode(2). Remarks : BLC(SET) Key Switches Menu Item selection Mode(2) and Menu Data change Mode(3).

4/5

APPENDIX 2

ONZ - AN101 /151/102/152 ( NTSC) ONZ - VP101 /151/102/152 ( PAL)

DATE : 11. Jul. ‘00REVISION No. 1.0

MODEL :

Measurement SpecificationsMeasurement Specifications

ONIX SYSTEM INC.


ONIX SYSTEM INC.

1. MEASUREMENT CONDITIONS1) Standard Measurement Conditions Supplied Voltage DC 12V ± 0.5 V Ambient Temperature 23 ℃ Humidity 60 % RH Measurement Fixture Video output , DC input , RS-232C level Convert ( 5Vpp -> 12Vpp) Power Supply 12V ± 0.5 V Color Monitor CMM20 - 11 , Shibasoku or Equivalent Monochrome Monitor More than 800 TV Lines Horizontal Resolution Waveform Monitor / Vector Scope 1720A , Tektronix ( NTSC / EIA ) or Equivalent 1730A , Tektronix ( PAL / CCIR ) or Equivalent S / N ( Signal to Noise )Meter VN31AX , Shibasoku ( NTSC/PAL/EIA/CCIR ) or Equivalent Illumination Meter / Color Temperature Meter XY-1 / CL-100 , Minolta Camera or Equivalent Light Box Dai Nippon Printing Co. - Color Temperature 3200 。 K ± 100 。 K - Illumination More than 2000 Lux Test Charts ( Transparent Chart ) Color Bar Chart , Dai Nippon Printing Co. Gray Scale Chart , Dai Nippon Printing Co. ( Gamma 0.45 ) Resolution Chart , Dai Nippon Printing Co. ( Reflective Chart ) Gray Scale Chart , Murakami Color Research Lab Light Source Halogen Lamp ( with Dimmer Switch ) - Color Temperature 3200 。 K ± 100 。 K - Illumination Variable with Dimmer Color Temperature Filter LB 140 , Hoya or Kenko or Equivalent ( Color Temperature Conversion Filter ) Adjustment PC With Serial Port 1 or 2 RS-232C Cable Each Terminal Connector ( D-Sub 9 Pin )

2. Measuring System1) System 1.

MeasurementFixture

Light Box

ColorMonitor

MonochromeMonitor

Waveform /Vector scope

FFC

PC withSerial Port2) System 2.

Light Source

Same as above System 1.

Camera

Camera

Reflective Chart

EQUIPMENTS

1/5


ONIX SYSTEM INC.

2. MEASUREMENT PROCEDURE

1. VIDEO OUPUT LEVEL

TEST CONDITIONS

MEASURING SYSTEM

Refer to “ 1. MEASUREMENT CONDITIONS “

System 1.

PROCEDURE :

1. Shoot the gray scale chart , and Zoom WIDE or TELE to fit a scene of monitor fully by PC .2. Measure the video output level on the waveform monitor ( Before the above measurement , Measure the SYNC and BURST level )

A

B

C

( Fig 1. ) Video Output Waveform

SPECIFICATION :

NTSC

Video Level A

Sync Level B

100 ± 10 IRE

40 ± 5 IRE

Burst Level C 40 ± 5 IRE

700 ± 70 mV

300 ± 35 mV

300 ± 35 mV

PAL

Video Level A

Sync Level B

Burst Level C

2/5


ONIX SYSTEM INC.

2. COLOR REPRODUCTION

TEST CONDITIONS

MEASURING SYSTEM


System 1.

PROCEDURE :

1. Shoot the color bar chart , and Zoom WIDE or TELE to fit a scene of monitor fully by PC . 2. Measure the color amplitude and color phase on the vector scope of Red,Blue,Yellow . ( Before the above measurement , Adjust the burst amplitude and phase on the vectorscope so that the burst level becomes 100% and its phase becomes 180 。 (NTSC) (135 。 PAL)

( Fig 2. ) Video Output Waveform

SPECIFICATION :

NTSCAmplitude ( % )

Phase ( 。 )

( Fig 3. ) Video Output Color Vector

100 %

180 。

RED BLUE YELLOW BURSTCOLOR

200 ± 40 %

103 ± 20 。

PALAmplitude ( % )

Phase ( 。 )

100 %

135 。

130 ± 40 %

345 ± 20 。 115 ± 40 %

170 ± 20 。 200 ± 40 %

103 ± 20 。 130 ± 40 %

345 ± 20 。 115 ± 40 %

170 ± 20 。

3/5


ONIX SYSTEM INC.

3. LUMINANCE S / N

TEST CONDITIONS

MEASURING SYSTEM


System 1.

PROCEDURE :

1. Shoot the light box , and zoom WIDE or TELE to fit a scene of monitor fully by PC . 2. The noise meter settings are ; Input level : Preset High Pass Filter : 100KHz Low Pass Filter : 4.2 MHz Sub-carrier Trap : On Weighting : On Sag & Hue Comp. : Optimum 3. Measure the maximum S/N on the noise meter .

SPECIFICATION :

NTSC : More than 48 dBPAL : More than 48 dB

4. HORIZONTAL RESOLUTION

TEST CONDITIONS

MEASURING SYSTEM


System 1.

PROCEDURE :

1. Shoot the resolution chart , and Zoom WIDE or TELE to fit a scene of monitor fully by PC . 2. Adjust the brightness and contrast of the B/W monitor so that each steps of gray scale part can be observed . 3. Change the scan size of monitor to underscan. 4. The reference arrows on the resolution chart are positioned at the edge of the underscanned picture . 5. Change the scan size of monitor from underscan to overscan . 6. Measure the maximum horizontal resolution on the picture .

SPECIFICATION :

More than 480 TV Lines ( High Resolution)More than 380 TV Lines ( Normal Resolution)

4/5


ONIX SYSTEM INC.

5. LOW LUMINANCE SENSITIVITY

TEST CONDITIONS

MEASURING SYSTEM


System 2.

PROCEDUTE :

1. Shoot the gray scale chart ( reflective ), and zoom WIDE fully by PC . 2. Adjust the brightness of the light source using the dimmer switch so that the white peak level of the chart becomes 30 IRE ( NTSC ) ( 210 mV ,PAL ) on the waveform monitor . 3. Measure the level of illumination using the illumination meter .

SPECIFICATION :

5/5

NTSC (HI) : 1 Lux ( 30 IRE )PAL (HI) : 1 Lux ( 210 mV )

NTSC (Normal) : 0.5 Lux ( 30 IRE )PAL (Normal) : 0.5 Lux ( 210 mV )

APPENDIX 2DATE : 14 . JULY. ‘00REVISION No. 1.1

RS - 232C Communication ProtocolRS - 232C Communication Protocol

ONIX SYSTEM INC.

ONZ - VN100 /150 ( NTSC )ONZ - VN101 /151 ( NTSC )ONZ - VN102 /152 ( NTSC )ONZ - VP100 /150 ( PAL )ONZ - VP101 /151 ( PAL )ONZ - VP102 /152 ( PAL )

MODEL :


ONIX SYSTEM INC.

1. Communication Format

2) The communication data format from PC to Camera

1 command consists of 11 codes and

The data of total 11 bytes are transmitted from PC to camera. TOTAL 11 ASCII CODES.

(b) Description ; 1’ST CODE : START CODE

2’ND CODE : THE HIGH CHARACTER OF CAMERA ID

3’RD CODE : THE LOW CHARACTER OF CAMERAI ID

4’TH CODE : COMMAND High

5’TH CODE : COMMAND Low

6’TH CODE : DATA 4




10’TH CODE : Check Sum High

11’TH CODE : Check Sum Low

(a) Format ;

3) The communication data format from Camera to PC (Echo back data format )

; The data of total 11 bytes are transmitted from Camera to PC. * TOTAL 11 ASCII

1) Connection Conditions ; Data Length 1 Byte = 1code ( 8 Bit )

Stop Bit 1 Bit

Parity Bit None

Baud rate 9,600 bps

First last

* IDH IDL CH CL D4 D3 D2 D1 C.SH C.SL

(b) Description ; 1’ST CODE : START CODE

2’ND CODE : DATA 8 ( ID Code does not affect communication now)

3’RD CODE : DATA 7 ( ID Code does not affect communication now)







10’TH CODE : Check Sum High

11’TH CODE : Check Sum Low

(a) Format ;

First last

* IDH IDL CH CL D4 D3 D2 D1 C.SH C.SL

* Check Sum Method: ADD data1 to data 9 without carry.* If it becomes 3A as result of checksum data, It needs to be changed to ASC code [ ‘3’ ‘A’] Ⅱ

Communication between the microcomputer of the camera and the PC is available

by using the RS - 232C. The microcomputer receives each control command given by the PC

through RXD INPUT TERMINAL and it echoes back to the PC through TXD OUTPUT TERMINAL

1/10


ONIX SYSTEM INC.

4) Communication Flow

2/10

start

Send command (11codes)

Are echo back data transmittedfrom camera ?

Delay 20 ms

Command transmission is ok !

Send next command

Camera returns echo back data after execution of command from PC,So , in case of “Internal Zoom TrackingPRESET Moving control command “Echo back data can be delayed to several seconds . The minimum delay time between command and echo back data is 1 Milli-second.

NO

END

YES

4) Miscellaneous for Communication

* When transmitting 11 code of command, keep 2 Milli-seconds of waiting time between codes.

* If command transmission is stopped after 3 code only , camera waits for the remain 8 codes continuously. At that moment, If new command ,starting from ‘*’ (Start code ) is transmitted to camera, the previous 3 codes are ignored !

* IF echo back codes are error , there can be some troubles in communication line or data receiving timing . On software, you can send command again !

* About echo back : After 1 command , you need to wait for echo back data from camera for Transmission confirmation and next command transmission . But 1 more command transmission is possible before echo back data 20 milli second after first transmission.


ONIX SYSTEM INC.

2. RS - 232C Communication Commands : ‘X’ indicates don’t care code and “YY” indicates checksum

1) Camera RESET Reset the micro controller ( u-COM ) of Camera.

2) Camera ID Display ON/OFF control

Switch the display of camera ID (ON/OFF).

3) CAM ID READ . ZZ : Camera ID

4) CAM ID CHANGE ; Change the data of CAM_ID to “ NEW_C_ID “ .

5) Key Action ; See Page 10

Key action can be activated by this command. *XX75ZZXXYY

ZZ : Key CODE

Caution ; When you want to stop key action, send this command again

by using “KC_STOP “

. KEY CODE : Refer to 10-3.( Key Code Table ) for desired

key action selection.

*XX71XXXXYY

*XX7201XXYY

*XX7200XXYY

; ID ON

; ID OFF

*XX73XXXXYY

*XX74ZZXXYY

ZZ : NEW ID CODE

6) Camera Power ON/Off Turn on the power of Camera. *XX760ZXXYY Z(1) : Power On Z(0) : Power Off

3/10

*XXZZXXXXYY :Return data

7) Function OSD Display Mode RD *XX79XXXXYY

Read the Function OSD Display Mode of the camera

*0ZXXXXXXYY ;return data

Return Data :

Z(0) : “ Function OSD ON” mode. : All osd display is enabled

Z(1) : “ Function OSD OFF” mode : Excluding Menu osd display ,All osd display is disabled.

8) Function OSD Display Mode Change *XX7A0ZXXYY

Change the Function OSD Display Mode of the camera

Z(0) : The Function OSD Display Mode is changed to

“ Function OSD ON” mode.

Z(1) : The Function OSD Display Mode is changed to

“ Function OSD OFF” mode.


ONIX SYSTEM INC.

10) Camera Read Command of Digital Effect status *XX7EXXXXYY

Read the current Digital Effect status of the Camera.

The return data is “DEFT_Status”.

Construction of DEFT_Status data *0ZXXXXXXYY ;RETURN DATA

Z(0) : NO DIGITAL EFFECT IS ACTIVATED

Z(1) : WIDE(Cinema effect) ON

Z(2) : ART ON

Z(3) : Mirror ON ,

Z(4) : Nega effect on.

Z(5) : COLOR OFF.

Z(6) : MOSAIC ON .

11) Read the Exposure Mode *XX80XXXXYY

Read the current Exposure Mode of the Camera.

The return data is “AE MODE”. *0ZXXXXXXYY ;return data

Z(0) : AUTO Exposure mode

Z(1) : SHUTTER Manual mode.

Z(2) : IRIS Manual mode.

Z(3) : AGC Manual mode

Z(4) : SHUTTER / IRIS / AGC All Manual mode

12) Exposure Mode Set Command *XX810ZXXYY Set the mode of Exposure according to “AE Mode”

Z(0) : AUTO Exposure mode Z(1) : SHUTTER Manual mode. Z(2) : IRIS Manual mode. Z(3) : AGC Manual mode Z(4) : SHUTTER / IRIS / AGC All Manual mode

4/10

9) CAMERA status Read Command *XX7C0ZXXYY

Read the current status of the Camera.

*0RXXXXXXYY(RETURN DATA)

Z(0) : Focus Mode READ --> R (0) : Focus Auto R(1) :Focus Manual

Z(1) : Camera ID Display ON mode, --> R (0) : Camera ID Display OFF R(1) :DISPLAY ON

Z(3) : BACKLIGHT ON state, --> R (0) : BACKLIGHT OFF R(1): Backlight On

Z(4) : FLICKERLESS ON state, --> R (0) : FLICKERLESS OFF R(1): Flickerless on

Z(8) : Auto BLC Mode, --> R (0) : Auto BLC Off Mode R(1): Auto BLC On Mode


ONIX SYSTEM INC.

13) BACKLIGHT Level Read *XX83XXXXYY

Read the current BACKLIGHT level of Camera . *XXZZXXXXYY ;return Data

ZZ : BACKLIGHT level. (data range 00 ~FF hex)

16) SHUTTER Speed Setting *XX86ZZXXYY

Set the shutter speed with the “shutter counter” . ZZ :shutter counter

14) BACKLIGHT Level Adjust *XX84ZZXXYY

Adjust the current BACKLIGHT level of Camera . ZZ: BACKLIGHT level.

(data range 00 ~FF hex)

15) SHUTTER Speed counter read *XX850000YY

Set the shutter speed with the “shutter counter” . *XX85ZZ00YY ;return data

ZZ : shutter counter

00 : 1/60 01:1/125 02:1/250 03:1/200

04 : 1/250 05:1/300 06:1/350 07:1/400

08 : 1/450 09:1/500 10:1/600 11:1/700

12 : 1/800 13:1/900 14:1/1000 15:1/1100

16 : 1/1200 17:1/1300 18:1/1500 19:1/1600

20 : 1/1800 21:1/2000 22:1/2500 23:1/3000

24 : 1/3500 25:1/4000 26:1/6000 27:1/10000

17) AGC Level Setting *XX87ZZXXYY

Set the AGC Level with the AGC data .

ZZ: AGC data

00(Minimum AGC Level) ~ FF Hex (Maximum AGC Level)

18) Read the current BRIGHTNESS data *XX88XXXXYY

Read the current BRIGHTNESS data of the Camera. *XXZZXXXXYY ;return data

The return data is “Brightness”.

ZZ : 00(Minimum Brightness level) ~ 60 Hex (Maximum Brightness Level)

19) Read the IRIS control data *XX89XXXXYY *XXZZXXXXYY ;return data

ZZ : IRIS Control Level (data range 00 ~FF hex)

5/10


ONIX SYSTEM INC.

20) IRIS Level Setting *XX8AZZXXYY

Set the IRIS OPEN Level

ZZ : IRIS control level (data range 00 ~FF hex)

21) Read the AGC control data *XX8B0000YY *XXZZ0000YY ;return data ZZ : Current AGC Control level (data range 00 ~FF hex)

22) IRIS Area Weighting Value Read *XX8EXXXXYY

Read the current weighting value of Iris area. *XXABXXXXYY ;return data

A:Region 1 weight data

B:Region 2 weight data

24) FLICKERLESS Mode ON/OFF Setting *XX900ZXXYY

Z(1) : Flickerless Mode Active

Z(0) : Flickerless Mode inactive

6/10

23) IRIS Area Weighting Value Write *XX8FXXXXYY

Read the current weighting value of Iris area.

A:Region 1 weight data

B:Region 2 weight data

25) BRIGHTNESS Data Setting *XX91ZZXXYY

ZZ : Brightness level desired (data range 00 ~ 60 hex)

26) Read the White Balance Mode *XXB1XXXXYY

Read the current White Balance Mode of the Camera. *XX0ZXXXXYY ;return data

Z(0) : Auto Mode Z(1) : Special Z(2) : indoor Z(3) : outdoor

Z(4) : Manual Z(5) : Push Auto

27) White Balance Mode Set Command *XXB20ZXXYY

Set the mode of White Balance of the camera.

Z(0) : Auto Mode Z(1) : Special Z(2) : indoor Z(3) : outdoor

Z(4) : Manual Z(5) : Push Auto

28) Read the current MANUAL White Balance Mode data *XXB3XXXXYY *XXB3ZZXXYY ;return data ZZ : (data range 00 ~60 hex)

R1 R2


ONIX SYSTEM INC.

29) MANUAL White Balance Mode MWB_CTL data Setting *XXB4ZZXXYY ZZ : (data range 00 ~60 hex)

30) Read the current SHARPNESS data *XXB5XXXXYY *XXB50ZXXYY ;return data

Z : “Sharpness Data” Data value range 0 ~ F

32) Read the RED Adjust data at the SPECIAL White Balance Mode *XXB7XXXXYY

*XXZZXXXXYY ;return data

ZZ : Red adjust data (data range 00 ~ FF hex)

33) Read the BLUE Adjust data at the SPECIAL White Balance Mode data *XXB8XXXXYY

*XXB8ZZXXYY ;return data

ZZ : Blue adjust data. (data range 00 ~ FF hex)

34) SPECIAL White Balance Mode RED adjust data Setting *XXB9ZZXXYY

ZZ : Red adjust data (data range 00 ~FF hex)

31) SHARPNESS data adjust *XXB60ZXXYY

Z : “Sharpness Data” Data value range 0 ~ F

7/10

35) SPECIAL White Balance Mode BLUE adjust data Setting *XXBAZZXXYY

ZZ : Blue adjust data (data range 00 ~FF hex)

36) Zoom Lens Position Read *XXC0XXXXYY

*XX0ABCDEYY ;return data

A : ZOOM POSITION HIGH

BC : ZOOM POSITION LOW

DE : DIGITAL ZOOM POSITION

* zoom position range ( 00 ~ 42F Hex)

* Digital zoom position range ( 00 ~ E0 Hex )

* : This command is used For Zoom Position setting In

external PRESET mode . ABCDE is expressed in Hex data

37) Focus Lens Position Read *XXC1XXXXYY

*XX0ABCXXYY

A : FOCUS POSITION HIGH

BC : FOCUS POSITION LOW

* focus position range ( 3F ~ 315 Hex)

* : This command is used For Zoom Position setting

In external PRESET mode . ABC is expressed in Hex data


ONIX SYSTEM INC.8/10

38) Memorize Internal PRESET Position for Internal PRESET control *XXC7ZZXXYY

Memorize the current zoom, focus, and digital zoom position

value into the internal nonvolatile memory of the CAMERA

for controlling the Internal PRESET Move. The memory position

to store is indicated by the “INDEX” value.

ZZ : (data range 00 ~ 3F hex) : Index counter

39) Internal Non Zoom Tracking PRESET Moving control *XXC8ZZXXYY

Perform the Internal PRESET Moving action.


40) Slow Speed Internal Zoom Tracking PRESET Moving control :XXCFZZXXYY

Perform the Zoom Tracking PRESET action to the target zoom

position slowly. The target zoom position value is memorized in the

internal nonvolatile memory.


41) Quick Speed Internal Zoom Tracking PRESET Moving control :XXD0ZZXXYY

Perform the Zoom Tracking PRESET action to the target zoom

position Quickly. The target zoom position value is memorized in the

internal nonvolatile memory.


CF) Internal Preset Mode usage 1. Using “Memorize Internal PRESET Position “ Command , Memorize each position To camera 2. Using “Preset Moving control “ Command , Move Zoom and Focus Lens to each Memorized position every position is accessed by index counter


ONIX SYSTEM INC.

Appendix: Key Code Table 1/2

KC_STOP 09 ; After the other key commands below this command must be followed after.

If continuous key service is needed send this command several seconds

after the before command.

In other words , when you want a certain function you can send below key codes

when you want to stop the function send this command again.

KC_POWER 0A ; Toggles power on/off status

KC_TELE 01 ; Slow zoom tele action

KC_WIDE 03 ; Slow zoom wide action

KC_QTELE 02 ;Fast zoom tele action

KC_QWIDE 04 ; Fast zoom wide action

KC_FAR 05 ;Focus lens move action to far direction ( in manual focus mode)

KC_NEAR 06 ;Focus lens move action to near direction ( in manual focus mode)

KC_FAM 0B ;Toggles focus Auto/Manual Modes

KC_F_PUSH 0C ; Activates Focus auto action on time

KC_SET 0D ; In menu mode , toggles item selection mode/ item adjust mode

KC_Default 0E ; by this code all conditions in camera returns to manufacturer’s conditions

KC_OSD 0F ; Toggles function osd off/on modes

KC_MENU 10 ; Toggles menu on/off modes

KC_BL 13 ; Toggles backlight mode

KC_FLICKER 14 ; Toggles flicker mode

KC_SSC Up 15 ; Shutter speed counter up

KC_SSC Down 16 ; Shutter speed counter down

KC_DEFT 17 ;Switches digital effect modes WIDE→ART → MIRROR → NEGA80

MONO → MOSAIC

KC_MIRROR Con. 18 ;Toggles Mirror mode

KC_NEGA 19 ;Toggles nega mode

KC_MONO 1A ;Toggles mono modeKC_WIDE 38 ; Toggles wide modeKC_MOSAIC 39 ;Toggles mosaic modeKC_ART 3A ; Toggles art mode

9/10


ONIX SYSTEM INC.

Appendix: Key Code Table 2/2

KC_SRPUP 1C ;sharpness data up

KC_SRPDN 1D ;sharpness data down

KC_BRTUP 1E ;Brightness data up

KC_BRTDN 1F ;Brightness data down KC_ZoomSup 20 ;Zoom Start upKC_ZoomSdn 21 ;Zoom Start downKC_ZoomEup 22 ;Zoom End upKC_ZoomEdn 23 ;Zoom End down

KC_WB_PUSH 24 ;In white balance push auto mode (manual mode ) ,initiates “push action”KC_AWBup 25 ;Switches awb modes auto → special → Indoor → outdoor → hue control → puah autoKC_AWBdn 26 ;Switches awb modes in reverse sequence to KC_AWBupKC_RadjUP 27 ;In Special WB mode ,R gain goes upKC_RadjDN 28 ;In Special WB mode ,R gain goes downKC_BadjUP 29 ;In Special WB mode ,B gain goes upKC_BadjDN 2A ;In Special WB mode ,B gain goes downKC_HUEUP 2B ;In HUE adjust WB Mode the picture become ReddishKC_HUEDN 2C ;In HUE adjust WB Mode the picture become BluishKC_AE_Man 2D ;Turns AE mode to Manual modeKC_IrisUp 2E ;Increase IRIS LevelKC_IrisDn 2F ;Decrease IRIS LevelKC_AGCup 30 ;Increase AGC GainKC_AGCdn 31 :Decrease AGC gain

END

Example of Key action transfer

# Zoom Lens moving example

Send commands following this sequence! 1 → 2 → 3

Every codes are transferred and received in ASCII codes

1. *XX75ZZXXYY ( move to tele )

XX=don’t care

ZZ = 01 (KC_TELE)

YY=Check Sum Data

=>assume XX to be 00 ,then the check sum becomes Y Y

2A(‘*’) + 30(‘0’)+ 30(‘0’)+37(‘7’)+35(‘5’)+ 30(‘0’)+ 31(‘1’)+30(‘0’)+ 30(‘0’) = ‘B’ ‘7’

2. Software delay ( The time you desired to move )

3. *XX75ZZXXYY (stop action )

ZZ:09 (KC_STOP)

10/10

approval sheet description : 16 x ccd color camera set model no. : onz - an101 /151/102/152 ( ntsc)...

Documents