appendix - black&white 1 copy · job01 richmond comments model number d--b45 coil information...
TRANSCRIPT
56
Appendix A
COILS FOR RUN-AROUND HEAT RECOVERY SYSTEM ________________________________________________________________________________
Cooling Coil
Model number D--B45
Coil Information
Note: Ratings outside the scope of the ARI Air-Cooling and Air-Heating Coils Certification Program.
Tag Exhaust WintQuantity System type Chilled Water
Actual airflow 19437 cfm
Elevation 0.00 ft
Rows 2
Fin spacing 143 fins per footFin material Aluminum
Fin type Delta flo ETube matl/wall thickness .016 (0.406 mm) copper
Coil type UW Coil tube drainability
Nominal coil height 45" (1143 mm)Finned length 126" (3200 mm)
Entering dry bulb 70.00 FEntering wet bulb 54.00 F
Sensible Capacity 212.27 MBhTotal capacity 212.28 MBh
Leaving dry bulb 60.00 FLeaving wet bulb 49.72 F
Turbulators Yes
Max face velocityMax Air PD
Max fin spacing
Actual coil face area 39.38 sq ftAPD 0.18 in H2OVolume 9.35 gal
Face velocity 493.64 ft/min
Installed weight 344.4 lb Rigging weight 252.6 lb
Unit size 80
Coil coating No
1
Chilled Water Information
Fouling factor 0.00000 hr-sq ft-deg Standard fluid flow rate 43.00 gpm
Fluid temp rise 11.23 F Entering fluid temp 45.00 F
Fluid type Ethylene GlycolFluid concentration 30.00 %
Leaving water temperature 56.23 F
Fluid PD 5.00 ft H2O
Fluid velocity 2.11 ft/sec
Reynolds number 2690.73 Each
Maximum water pressure drop
03/01/2005
57
Cooling coilRefrigerant Information
Suction temp Liquid temp Refrigerant type
Circuiting type
DX circuits - ent air side DX circuits - lvg air side
Distributor type - ent air side Distributor type - lvg air side
LDB - ent air vert split Packed elbows LWB - ent air vert split
Number of distr - ent coil type #1 Number of distr - lvg coil type #1 Number of distr - ent coil type #2 Number of distr - lvg coil type #2 Number of distr - ent coil type #3 Number of distr - lvg coil type #3 Total cap ent coil type #1 Total cap lvg coil type #1Total cap ent coil type #2 Total cap lvg coil type #2Total cap ent coil type #3 Total cap lvg coil type #3
Stacked Coil Information
Coil bank airflow 38874 cfm
Coil bank sensible cap 424.54 MBhCoil bank total cap 424.56 MBh
Coil bank standard flow rate 86.00 gpmCoil bank volume 18.71 gal
Coil bank installed weight 688.8 lbCoil bank rigging weight 505.1 lb
Coil bank fluid PD 5.00 ft H2O
Qty of stacked coil #1 Qty of stacked coil #2 Qty of stacked coil #3 Nominal ht stacked coil #1 Nominal ht stacked coil #2 Nominal ht stacked coil #3
03/01/2005
58
Job01Cooling coil ( CLCL ) Items: Exhaust Wint Exhaust WintTags: Exhaust Wint Exhaust Wint03/01/2005 07:15:50 PM
Page: 1ALL WEIGHTS AND DIMENSIONS ARE APPROXIMATE. CERTIFIED PRINTS ARE AVAILABLE UPON REQUEST.TOPSS Dimension Drawing
3/8" (10mm ) NP T ( INT ) VE NT
2 1/2" ( 64m m ) NP T (E XT ) RET URN L.H.
2 1 /2" (64m m ) NPT ( EX T) S UPP LY L.H.
3/8" ( 10m m ) NP T (INT) DRAIN
2 1/2" (64m m ) NPT ( EX T) RE TURN R.H.
2 1 /2" ( 64m m ) NP T (E XT ) SUP PLY R.H.
AIR
FLOW
LE FT HA ND
A IR
FLOW
RIGHT HAND
8 1/ 8" (20 6mm ) (R.H .)
5 1/4" (133m m) (R .H .)
8 1/8" (206 mm) (L .H.)
7 8" (19 81mm )
58" (1 473m m)
3 1 1/2" (800 mm)
11 1 /2" (2 92mm )
1 02 1/ 8" (25 94mm )
8 1 1/8" (2061 mm)
54 5/8 " (13 87mm )
3 4 5/8 " (879 mm)
5 1 /4" (1 33mm ) (L.H .)
59
Cooling coilJob Information
Job01 Richmond
Comments
Model number D--B45
Coil Information
Note: Ratings outside the scope of the ARI Air-Cooling and Air-Heating Coils Certification Program.
Tag Exhaust WintQuantity System type Chilled Water
Actual airflow 19437 cfm
Elevation 0.00 ft
Rows 2
Fin spacing 143 fins per footFin material Aluminum
Fin type Delta flo ETube matl/wall thickness .016 (0.406 mm) copper
Coil type UW Coil tube drainability
Nominal coil height 45" (1143 mm)Finned length 126" (3200 mm)
Entering dry bulb 70.00 FEntering wet bulb 54.00 F
Sensible Capacity 212.27 MBhTotal capacity 212.28 MBh
Leaving dry bulb 60.00 FLeaving wet bulb 49.72 F
Turbulators Yes
Max face velocityMax Air PD
Max fin spacing
Actual coil face area 39.38 sq ftAPD 0.18 in H2OVolume 9.35 gal
Face velocity 493.64 ft/min
Installed weight 344.4 lb Rigging weight 252.6 lb
Unit size 80
Coil coating No
1
Chilled Water Information
Fouling factor 0.00000 hr-sq ft-deg Standard fluid flow rate 43.00 gpm
Fluid temp rise 11.23 F Entering fluid temp 45.00 F
Fluid type Ethylene GlycolFluid concentration 30.00 %
Leaving water temperature 56.23 F
Fluid PD 5.00 ft H2O
Fluid velocity 2.11 ft/sec
Reynolds number 2690.73 Each
Maximum water pressure drop
03/01/2005
60
Cooling coilRefrigerant Information
Suction temp Liquid temp Refrigerant type
Circuiting type
DX circuits - ent air side DX circuits - lvg air side
Distributor type - ent air side Distributor type - lvg air side
LDB - ent air vert split Packed elbows LWB - ent air vert split
Number of distr - ent coil type #1 Number of distr - lvg coil type #1 Number of distr - ent coil type #2 Number of distr - lvg coil type #2 Number of distr - ent coil type #3 Number of distr - lvg coil type #3 Total cap ent coil type #1 Total cap lvg coil type #1Total cap ent coil type #2 Total cap lvg coil type #2Total cap ent coil type #3 Total cap lvg coil type #3
Stacked Coil Information
Coil bank airflow 38874 cfm
Coil bank sensible cap 424.54 MBhCoil bank total cap 424.56 MBh
Coil bank standard flow rate 86.00 gpmCoil bank volume 18.71 gal
Coil bank installed weight 688.8 lbCoil bank rigging weight 505.1 lb
Coil bank fluid PD 5.00 ft H2O
Qty of stacked coil #1 Qty of stacked coil #2 Qty of stacked coil #3 Nominal ht stacked coil #1 Nominal ht stacked coil #2 Nominal ht stacked coil #3
03/01/2005
61
Job01Cooling coil ( CLCL ) Items: Exhaust Wint Exhaust WintTags: Exhaust Wint Exhaust Wint03/01/2005 07:15:50 PM
Page: 1ALL WEIGHTS AND DIMENSIONS ARE APPROXIMATE. CERTIFIED PRINTS ARE AVAILABLE UPON REQUEST.TOPSS Dimension Drawing
3/8" (10mm ) NP T ( INT ) VE NT
2 1/2" ( 64m m ) NP T (E XT ) RET URN L.H.
2 1 /2" (64m m ) NPT ( EX T) S UPP LY L.H.
3/8" ( 10m m ) NP T (INT) DRAIN
2 1/2" (64m m ) NPT ( EX T) RE TURN R.H.
2 1 /2" ( 64m m ) NP T (E XT ) SUP PLY R.H.
AIR
FLOW
LE FT HA ND
A IR
FLOW
RIGHT HAND
8 1/ 8" (20 6mm ) (R.H .)
5 1/4" (133m m) (R .H .)
8 1/8" (206 mm) (L .H.)
7 8" (19 81mm )
58" (1 473m m)
3 1 1/2" (800 mm)
11 1 /2" (2 92mm )
1 02 1/ 8" (25 94mm )
8 1 1/8" (2061 mm)
54 5/8 " (13 87mm )
3 4 5/8 " (879 mm)
5 1 /4" (1 33mm ) (L.H .)
62
Heating Coil (HTCL)
Job Information
Job01 Richmond
Comments
Model number D--B24
Coil Information
Steam Information
Stacked InformationHot Water Information
Note: Rated and Certified in accordance with the current edition of ARI Standard 410.
Tag AHU-3 Wint Quantity 1 System type Hot Water Unit size 66 Coil type 5W Coil tube drainability Drainable Rows 1
Nominal coil height 24" (610 mm)Finned length 126" (3200 mm)
Fin type Prima-Flo H
Tube matl/wall thickness .020 (0.508 mm) copperFin spacing 130 fins per footFin material Aluminum
Coil coating No Turbulators Yes
Actual airflow 12265 cfmEntering dry bulb 8.00 FLeaving dry bulb 21.44 FTotal capacity 178.74 MBhActual coil face area 21.00 sq ftAPD 0.15 in H2OVolume 3.14 galElevation 0.00 ft
Max face velocity
Face velocity 584.06 ft/minMax air PD
Max fin spacingRigging weight 104.9 lbInstalled weight 131.0 lb
Fluid type Ethylene GlycolFluid concentration 30.00 % Standard fluid flow rate 36.21 gpm Entering fluid temp 56.00 F Fluid temp drop 11.23 F Leaving fluid temp 44.77 F Fluid PD 20.45 ft H2O
Fluid velocity 5.00 ft/sec Max fluid PD
Fouling factor 0.00050 hr-sq ft-deg
Modulated Degrees superheat Condensate flow rate
Steam PD Steam pressure
Qty of stacked coil #1Qty of stacked coil #2Qty of stacked coil #3Nominal ht stacked coil #1Nominal ht stacked coil #2Nominal ht stacked coil #3
Coil bank airflow 29130 cfmCoil bank total cap 424.50 MBhCoil bank standard flow rate 86.00 gpmCoil bank fluid PD 20.45 ft H2O
Coil bank installed weight 311.2 lbCoil bank rigging weight 249.2 lbCoil bank volume 7.45 gal
Reynolds number 7921.06
63
Job01Heating coil ( HTCL ) Items: AHU-3 Wint AHU-3 WintTags: AHU-3 Wint AHU-3 Wint03/01/2005 07:15:49 PM
Page: 1ALL WEIGHTS AND DIMENSIONS ARE APPROXIMATE. CERTIFIED PRINTS ARE AVAILABLE UPON REQUEST.TOPSS Dimension Drawing
NPT (EXT) RETURN
NPT (EXT) SUPPLY
NPT (INT) DRAIN3/8" (9mm)
1 1/2" (38mm)
1 1/2" (38mm)
NPT (INT) VENT3/8" (9mm)
AIR
FLOW
1 1/8" (29mm)
1 1/8" (29mm)
24" 5W 1 ROW
4" (102mm)
25 1/2"(648mm)
9" (229mm)
9" (229mm)
64
Heating Coil (HTCL)Job Information
Job01 Richmond
Comments
Model number D--B33
Coil Information
Steam Information
Stacked InformationHot Water Information
Note: Rated and Certified in accordance with the current edition of ARI Standard 410.
Tag AHU-3 Wint Quantity 1 System type Hot Water Unit size 66 Coil type 5W Coil tube drainability Drainable Rows 1
Nominal coil height 33" (838 mm)Finned length 126" (3200 mm)
Fin type Prima-Flo H
Tube matl/wall thickness .020 (0.508 mm) copperFin spacing 130 fins per footFin material Aluminum
Coil coating No Turbulators Yes
Actual airflow 16865 cfmEntering dry bulb 8.00 FLeaving dry bulb 21.44 FTotal capacity 245.76 MBhActual coil face area 28.87 sq ftAPD 0.15 in H2OVolume 4.31 galElevation 0.00 ft
Max face velocity
Face velocity 584.06 ft/minMax air PD
Max fin spacingRigging weight 144.3 lbInstalled weight 180.2 lb
Fluid type Ethylene GlycolFluid concentration 30.00 % Standard fluid flow rate 49.79 gpm Entering fluid temp 56.00 F Fluid temp drop 11.23 F Leaving fluid temp 44.77 F Fluid PD 20.45 ft H2O
Fluid velocity 5.00 ft/sec Max fluid PD
Fouling factor 0.00050 hr-sq ft-deg
Modulated Degrees superheat Condensate flow rate
Steam PD Steam pressure
Qty of stacked coil #1Qty of stacked coil #2Qty of stacked coil #3Nominal ht stacked coil #1Nominal ht stacked coil #2Nominal ht stacked coil #3
Coil bank airflow 29130 cfmCoil bank total cap 424.50 MBhCoil bank standard flow rate 86.00 gpmCoil bank fluid PD 20.45 ft H2O
Coil bank installed weight 311.2 lbCoil bank rigging weight 249.2 lbCoil bank volume 7.45 gal
Reynolds number 7921.06
03/01/2005
65
Job01
Heating coil ( HTCL ) Items: AHU-3 Wint AHU-3 WintTags: AHU-3 Wint AHU-3 Wint03/01/2005 07:15:49 PM
Page: 2ALL WEIGHTS AND DIMENSIONS ARE APPROXIMATE. CERTIFIED PRINTS ARE AVAILABLE UPON REQUEST.TOPSS Dimension Drawing
NPT (EXT) RETURN
NPT (EXT) SUPPLY
NPT (INT) DRAIN3/8" (9mm)
1 1/2" (38mm)
1 1/2" (38mm)
NPT (INT) VENT3/8" (9mm)
AIR
FLOW
33" 5W 1 ROW
4" (102mm)
34 1/2"(876mm)
13 1/2" (343mm)
1 1/8" (29mm)
13 1/2" (343mm)
1 1/8" (29mm)
66
Appendix B
PUMP FOR HEAT RECOVERY SYSTEM
67
Appendix C
EXPANSION TANK FOR HEAT RECOVERY SYSTEM
68
69
Appendix D
DISTRIBUTED PUMPING PUMP SELECTIONS ________________________________________________________________________ AHU-1:
70
AHU-2:
71
AHU-3:
72
AHU-4:
73
Appendix E
RC-CURVES