anchor bay
TRANSCRIPT
Anchor Bay
Specialist suppliers to the building and construction industry
ContentsTying wires 4
Concrete spacers 5
Plastic spacers 6
Wire spacers 8
Fabric reinforcement 9
Bolt boxes, holding down bolts and grouts 10
Slab accessories 12
Polythene damp proof membranes 14
Resin anchor system 15
Joint fillerboards 16
Crack inducers and void formers 18
Surface treatment chemicals 19
Fosroc – waterproofing membranes 21
Waterstops – Fosroc range 22
Fosroc joint sealants 24
Grace – waterproofing membranes 26
Waterstop – Grace servicised range 28
Cetco – waterproofing system 29
Fosroc concrete repair 30
Concrete repair 31
Formwork tie rod system 32
Formwork accessories 34
Formwork chemicals 36
Monotub formwork systems 38
Formwork systems 39
Kwikastrip continuity system 40
Halfen HDB punching shear reinforcement 41
Formrib and rebar couplers 42
Concrete finishing tools 43
Concrete test equipment 44
Protection products 45
Halfen-brick tie products 46
Expamet brick tie products 48
Tools 50
Setting out products 52
Cut and bent reinforcements 53
Terms and conditions 54
Telephone 0870 24 24 234 Fax 0870 24 03 6134 Anchor Bay 2005
Black annealed tying wire
Stainless steel tying wire
Loop ties & tying tool
Tying wire nips
Tying wires
A soft black annealed 16 gauge wire
used for the tying of reinforcement.
18 gauge stainless steel tying wire used
for the tying of reinforcement.
An alternative way of tying reinforcement.
The tie is folded around the rebar and
tightened by the action of the tying tool.
The most popular tool used by all steel
fixers for the tying of reinforcement.
Code Pack
TW16 Coil
Code Pack
SS18 Kilo
Code Pack
WT150 1000
Wt/tool Each
Code Pack
Nips Each
Telephone 0870 24 24 234 Fax 0870 24 03 613 Anchor Bay 2005 5
Concrete spacers
Single cover spacers
Double cover spacers
Triple cover spacers
Concrete square bar
A concrete spacer designed to offer a
single cover to reinforcement ideally used
in horizontal applications.
Used for supporting reinforcement in
both vertical and horizontal applications.
Each block provides two separate
covers.
A concrete spacer used in vertical and
horizontal applications which offers three
separate covers.
A heavy duty bar spacer used for
supporting large reinforcement in heavy
duty slabs.
Code Cover Pack
SB20 20mm 1000
SB25 25mm 500
SB30 30mm 500
SB35 35mm 250
SB40 40mm 250
SB50 50mm 250
SB60 60mm 200
SB75 75mm 100
Code Cover Pack
SB15/20 15 & 20 1000
SB25/30 25 & 30 500
SB30/40 30 & 40 250
SB35/45 35 & 45 250
SB40/50 40 & 50 250
SB60/75 60 & 75 100
Code Cover Pack
SB20/25/30 20,25,30 500
SB35/40/50 35,40,50 250
Code Cover Pallet
20SQ20 20mm 1000
25SQ25 25mm 800
30SQ30 30mm 600
40SQ40 40mm 300
50SQ50 50mm 250
60SQ50 60mm 150
75SQ75 75mm 100
Telephone 0870 24 24 234 Fax 0870 24 03 6136 Anchor Bay 2005
Code Cover Pack
TK15 15mm 100m
TK20 20mm 100m
TK25 25mm 100m
TK30 30mm 100m
TK35 35mm 50m
TK40 40mm 50m
TK50 50mm 50m
Code Cover Bar dia. Pack
20SW12 20mm 4 to 12 1000
25SW12 25mm 4 to 12 500
25SW20 25mm 8 to 20 500
30SW12 30mm 4 to 12 500
30SW20 30mm 8 to 20 500
35SW12 35mm 8 to 12 250
35SW20 35mm 10 to 20 250
40SW12 40mm 4 to 12 250
40SW20 40mm 8 to 20 250
50SW12 50mm 4 to 12 250
50SW20 50mm 8 to 20 250
Code Cover Pack
25MF30 25/30mm 1000
40MF50 40/50mm 250
65MF75 65/75mm 250
90MF100 90/100mm 100
Track spacer
Wheel spacers
Meshfix spacers
Plastic spacers
A continuous plastic spacer for
supporting bottom reinforcement in
suspended slabs. Also used on metal
because of its stability and excellent
concrete flow characteristics.
A robust clip-on plastic spacer wheel.
Ideal for the use on columns, walls and
beams. Offers minimum contact with
formwork.
A heavy duty double cover plastic spacer
designed to support mesh and rebar off
polystyrene insulation and polythene.
Membranes in ground slabs.
Telephone 0870 24 24 234 Fax 0870 24 03 613 Anchor Bay 2005 7
Code Cover Bar dia. Pack
20NP20 20mm 8 to 20 1000
25NP20 25mm 8 to 20 1000
30NP20 30mm 8 to 20 1000
35NP20 35mm 8 to 20 500
40NP20 40mm 8 to 20 500
50NP20 50mm 8 to 20 500
Code Cover Bar dia. Pack
50HD20 50mm 6 to 20 250
75HD20 75mm 6 to 20 100
Code Size Pack
(Horseshoe)
LS02 2mm 250
LS03 3mm 250
LS05 5mm 125
LS07 7mm 125
LS09 9mm 125
LS10 10mm 250
LS20 20mm 150
(Plain)
LS02P 2mm 250
LS03P 3mm 250
LS05P 5mm 125
LS07P 7mm 125
LS09P 9mm 125
LS10P 10mm 250
LS20P 20mm 150
Clip chair spacers
Pile cage spacers
Levelling shims
A heavy duty single cover spacer clip-on
chair spacer designed for all pre-cast and
site applications.
A heavy duty clip-on plastic wheel spacer
designed for in-situ piling and diaphragm
wall applications.
A hard plastic shim used for packing
during the alignment of precast panels.
Supplied in plain or horseshoe styles.
Horseshoe
Plain
Plastic spacers cont.
Telephone 0870 24 24 234 Fax 0870 24 03 6138 Anchor Bay 2005
Code Cover Pack
DK50 50mm 50m
DK60 60mm 50m
DK75 75mm 50m
DK90 90mm 50m
DK105 105mm 50m
DK120 120mm 50m
DK135 135mm 50m
DK150 150mm 50m
DK165 165mm 50m
DK180 180mm 50m
DK200 200mm 50m
DK220 220mm 50m
DK230 230mm 50m
DK250 250mm 50m
DK270 270mm 50m
DK280 280mm 50m
DK300 300mm 50m
Code Cover Pack
CS50 50mm 25
CS60 60mm 25
CS75 75mm 25
CS90 90mm 25
CS105 105mm 25
CS120 120mm 25
CS135 135mm 25
CS150 150mm 25
CS165 165mm 25
CS180 180mm 25
CS200 200mm 25
Deckchairs
Hoop spacers
A welded girder used for supporting
fabric and reinforcement without
damaging the polythene membrane.
They can also be used to support dowel
bars. Supplied in 2 metre lengths.
A fast and economical way to support
mesh reinforcement in slabs. The hoops
are formed into a 1 metre diameter circle
and three or four hoops per sheet of
mesh is generally sufficient.
Wire spacers
Telephone 0870 24 24 234 Fax 0870 24 03 613 Anchor Bay 2005 9
Fabric reinforcement
Standard fabricManufactured to BS 4483 from cold reduced wire which complies with BS 4482.
Each wire intersection is resistance welded using electronically controlled techniques.
Standard sheet size: 4.8m x 2.4m
Merchant sheet size: 3.6m x 2.0m
Mesh size Cross sectional Nominal Sheets Sheet Sheets Sq. metres BS nominal pitch Wire sizes area per weight per weight per per ref. of wires meter width per m2 tonne (kg) bundle tonne Main Cross Main Cross Main Cross (kg) (approx) (mm) (mm) (mm) (mm) (mm) (mm)
A393 200 200 10 10 393 393 6.16 15 70.96 18 162.34 A252 200 200 8 8 252 252 3.95 22 45.50 28 253.16 A193 200 200 7 7 193 193 3.02 29 34.79 34 331.13 A142 200 200 6 6 142 142 2.22 40 25.57 46 450.45 A98 200 200 5 5 98 98 1.54 57 17.74 60 649.35
B1131 100 200 12 8 1131 252 10.90 8 125.57 10 91.74 B785 100 200 10 8 785 252 8.14 11 93.57 14 122.85 B503 100 200 8 8 503 252 5.93 15 68.31 18 168.63 B385 100 200 7 7 385 193 4.53 20 52.19 24 220.75 B283 100 200 6 7 283 193 3.73 24 42.97 30 268.10 B196 100 200 5 7 196 193 3.05 29 35.14 36 327.87
C785 100 400 10 6 785 70.8 6.72 13 77.41 16 148.81 C636 100 400 9 6 636 70.8 5.55 16 63.94 20 180.18 C503 100 400 8 5 503 49.0 4.34 20 50.00 26 230.41 C385 100 400 7 5 385 49.0 3.41 26 39.28 30 293.26 C283 100 400 5 5 283 49.0 2.61 34 30.07 32 383.14
D98 200 200 5 5 98.0 98.0 1.54 57 17.74 60 649.35 D49 100 100 2.5 2.5 49.1 49.1 0.77 113 8.87 50 1298.70
Standard sizes (4,800 x 2,400)
Mesh size Cross sectional Nominal Sheets Sheet Sheets Sq. metres BS nominal pitch Wire sizes area per weight per weight per per ref. of wires meter width per m2 tonne (kg) bundle tonne Main Cross Main Cross Main Cross (kg) (approx) (mm) (mm) (mm) (mm) (mm) (mm)
A393 200 200 10 10 393 393 6.16 23 44.35 26 162.34 A252 200 200 8 8 252 252 3.95 35 28.44 30 253.16 A193 200 200 7 7 193 193 3.02 46 21.74 50 331.13 A142 200 200 6 6 142 142 2.22 63 15.98 50 450.45
Merchant size (3,600 x 2,000)
Telephone 0870 24 24 234 Fax 0870 24 03 61310 Anchor Bay 2005
Waxed cardboard bolt box
Polystyrene bolt box
Expanded metal bolt boxes
Holding down bolts
Made from waxed cardboard, they
provide an easy method of bolt alignment
for steel frame buildings.
An economical way of providing a void
around holding down bolts for steel
frame buildings.
Made from expanded metal for the
positioning of holding down bolts where
the bolt box is to remain in the concrete.
A range of high tensile grade 8.8 holding
down bolts complete with nuts and
washer plates 100 x 100 x 10mm
Bolt boxes, holding down bolts and grouts
Code Depth Taper
CB1 225mm 70 x 20
CB2 300mm 92 x 20
CB3 375mm 108 x 25
CB4 460mm 114 x 25
CB5 535mm 118 x 30
CB6 610mm 133 x 30
CB7 760mm 133 x 30
Code Depth
PC0 150mm
PC1 225mm
PC2 300mm
PC3 375mm
PC4 450mm
PC5 525mm
PC6 610mm
Code Description
DIS05 Disolver 5ltr
DIS25 Disolver 25ltr
Code Depth/Diameter
EXP0 150mm x 75mm
EXP1 225mm x 75mm
EXP2 300mm x 75mm
EXP3 375mm x 100mm
EXP4 450mm x 100mm
EXP5 600mm x 100mm
Code Size
20HDB300 M20 x 300mm
20HDB375 M20 x 375mm
20HDB450 M20 x 450mm
24HDB375 M24 x 375mm
24HDB450 M24 x 450mm
Telephone 0870 24 24 234 Fax 0870 24 03 613 Anchor Bay 2005 11
Non shrink grout
Cebex 100
Denso tape
A high strength non shrink cementitious
grout when added to water provides
excellent free flow properties for grouting
in holding down bolts.
Coverage: 13 litres/25kg approx.
Is an admixture for site batched
cementitious grouts where a reduced
water/cement ratio and positive
expansion is required.
Yield:
50kg of opc + 20-22 ltrs water
+ 225g cebex 100 = 36 litres
50Kg op opc + 22-24 ltrs water
+ 225g cebex 100 = 57 litres
Used to protect bolt heads prior to pouring concrete. Roll size: 75mm x 10m
Bolt boxes, holding down bolts and grouts cont.
Code Size/Detail
NSG25 25kg
PADDLE Mixing paddle
Code Size
COM100 24 x 225g
Code Size
DEN75 75mm x 10m
Telephone 0870 24 24 234 Fax 0870 24 03 61312 Anchor Bay 2005
Slab accessories
Dowel bars
Dowel bar sleeves
Compression foam plugs
Dowel bar caps
Plain round mild steel dowel bars used in
contraction and expansion joints in slabs.
Other sizes available on request.
A flexible pvc sleeve which provides
a very efficient method of debonding
mild steel dowel bars. Meets with all
D.O.T. specifications.
A foam plug supplied separately for
insertion into dowel bar sleeves to allow
for expansion.
A rigid pvc tube with a compressible
filler one end which is designed to
allow for expansion of dowel bars in
construction joints.
Code Size
12DB900 12mm x 900mm
12DB1000 12mm x 1000mm
16DB400 16mm x 400mm
16DB600 16mm x 600mm
16DB900 16mm x 900mm
20DB500 20mm x 500mm
20DB600 20mm x 600mm
25DB600 25mm x 600mm
Code Size Pack
12DBS450 12mm x 450mm 100
16DBS450 16mm x 450mm 100
20DBS300 20mm x 300mm 100
20DBS450 20mm x 450mm 100
25DBS300 25mm x 300mm 100
32DBS375 32mm x 375mm 100
Code Size Pack
FP12 12mm 100
FP16 16mm 100
FP20 20mm 100
FP25 25mm 100
FP32 32mm 100
Code Size Pack
12DC100 12mm 100
16DC100 16mm 100
20DC100 20mm 100
25DC100 25mm 100
32DC100 32mm 100
Telephone 0870 24 24 234 Fax 0870 24 03 613 Anchor Bay 2005 13
Debonding compound
Dowel bar cradles
Plastic screed chairs
Metal screed chairs
Heavy duty metal screed chair
Screed chair rail
Code Pack
DB05 5ltr
DB25 25ltr
Expansion joint cage.
Contraction joint cage.
Code Product Pack
SC/SET Base,collar,saddle 100
T22 Shaft 100m
Code Slab thickness Pack
TUFF1 120mm - 150mm Each
TUFF2 150mm - 200mm Each
TUFF3 200mm - 300mm Each
TUFF4 300mm - 400mm Each
Code Slab thickness Pack
HDSC 0mm - 500mm Each
Code Pack
S/RAIL 7.5m
Slab accessories cont.
A bitumen based compound used for
bond breaking of dowel bars in concrete.
Complies to Clause 2605 of D.O.E.
specification for roads and bridge works.
An accurate method used to support
dowel bars in contraction and expansion
joints in floor slabs and road construction.
An easily adjustable plastic screed
chair which is designed to be left in the
concrete part or whole. Suitable for
use with scaffold tubes or Anchor Bay
screeding rail.
For slabs 150mm-350mm.
A sturdy two component metal screed
chair for screeding slabs up to 400mm.
A heavy duty re-usable and fully
adjustable metal screed chair for slabs
up to 500mm. For long life wash and oil
after use.
Used in conjunction with screed chairs.
Size: 50mm x 25mm x 3mm
Length: 7.5 metre
Telephone 0870 24 24 234 Fax 0870 24 03 61314 Anchor Bay 2005
Polythene DPM
Temporary protective sheeting
Jointing tapes
Geotextile
Terram
Polythene damp proof membrane
A polythene damp proof membrane
manufactured to BBA standards 97/3393.
Ideal as a temporary protective sheet.
Colour: opaque.
A 75mm wide tape designed for the sealing of
laps on polythene DPM’s. A double sided tape
used in the sealing of laps on polythene DPM’s.
A cost effective solution to the problem of
constructing stable granular layers over soft
foundation soils.
Terram nonwoven geotextile provides an
effective solution to the age old problem of
constructing stable granular layers over soft
foundation soils.
Code Gauge Roll size
500BBAB 500 4m x 50m
1000BBAB 1000 4m x 25m
1200BBAB 1200 4m x 25m
2000BBAB 2000 4m x 12.5m
Code Gauge Roll size
HDPS 65 4m x 25m
Code Size Pack
JT75 75mm x 33m 16
D/SIDE30 30mm x 30m 10
Code Roll size
GEOTEX 4.5m x 100m
Code Roll size
TERRAM/1 4.5m x 100m
Telephone 0870 24 24 234 Fax 0870 24 03 613 Anchor Bay 2005 15
Code Description
L/SETS25 Lokfix S25
L/SETP25 Lokfix P25
Code Description
EASI-CHEM Easi-chem 380ml
RESGUN Applicator gun
Code Description
SKELG Skeleton gun
CART Blank cartridge
P/PUMP Putzi pump
PADDLE Mixing paddle
Resin anchor system
Fosroc Lokfix
Anchor Bay polyester resin
Application equipment
Calculation table
The two versions of lokfix are pre-
measured, two-part, filled polyester
resin grouts. After hardening, the grout
produces anchorages of consistent
reproducible values.
Lokfix S25 pour grade is for use where
the hole is 8 to 40mm greater in diameter
than the bar.
Lokfix P25 pump grade is used in
overhead or horizontal holes where the
hole is up to 25mm greater in diameter
than the bar.
A thixotropic low-slump polyester resin
grout for anchoring bolts, dowel bars,
starter bars, into vertical and sloping
plane concrete, rock and masonry.
Size: 380ml
A range of accessories used in the
application of resin grouts.
A guide table to calculate the volume of
resin grout required per hole.
Hole Bolt diameter diameter 12mm 16mm 20mm 25mm 32mm 38mm 44.5mm 51mm
20mm 0.020 litre
25mm 0.038 litre 0.029 litre
32mm 0.069 litre 0.060 litre 0.049 litre 0.031 litre
38mm 0.093 litre 0.082 litre 0.064 litre
45mm 0.128 litre 0.110 litre 0.079 litre 0.046 litre
51mm 0.155 litre 0.124 litre 0.091 litre
57mm 0.206 litre 0.175 litre 0.142 litre 0.100 litre
64mm 0.273 litre 0.241 litre 0.208 litre 0.166 litre 0.117 litre
76mm 0.298 litre 0.249 litre
Telephone 0870 24 24 234 Fax 0870 24 03 61316 Anchor Bay 2005
Code Thickness
12FBS 12mm
20FBS 20mm
25FBS 25mm
Width 12mm 20mm 25mm
100mm 12FB100 20FB100 25FB100
125mm 12FB125 20FB125 25FB125
150mm 12FB150 20FB150 25FB150
175mm 12FB175 20FB175 25FB175
200mm 12FB200 20FB200 25FB200
225mm 12FB225 20FB225 25FB225
250mm 12FB250 20FB250 25FB250
Code Thickness
KORK/10 10mm
KORK/13 13mm
KORK/19 19mm
KORK/25 25mm
Joint fillerboards
Wood fibre fillerboard
Korkpak fillerboards
Is a compressible joint fillerboard
manufactured from bitumen impregnated
wood fibres. It is supplied in sheet
form and is used to form and fill
expansion joints in in-situ and pre-cast
concrete construction. Complies to
DTP specification for Highway Works
Dec 1991 Series 1000 Clause 1015
(Pavement Joints).
Sheet size 1.220m x 2.440m
Preformed bitumen bonded cork joint
fillerboard for critical water retaining, civil
and structural expansion joints.
Sheet size 2.0m x 1.0m.
Cut strips available on request.
Telephone 0870 24 24 234 Fax 0870 24 03 613 Anchor Bay 2005 17
Joint fillerboards cont.
Foam fillerboard
Hydrocell XL joint fillerboard
Adhesives
Is a closed cell polyethylene joint filler
for use as expansion joint filler in brick
and blockwork, isolation joints and hinge
joints where a readily compressible low
load transfer joint filler is required. Density
35kg/m3. Supplied in sheets and cut
strips with tear off.
Sheet size: 2.0m x 1.6m
A crossed linked, non absorbent,
semi-rigid, cellular polyethylene joint used
for forming expansion joints in concrete,
brickwork and blockwork. The product
provides excellent support to sealants
subject to hydrostatic pressure and is
particularly recommended for water
retaining or water excluding structures.
Density: 60 kg/m3. Sheet size: 1.8m x
0.9m. Cut strips available on request.
A contact adhesive designed for the
fixing of fillerboards to a wide range
of surfaces.
Code Thickness
10EXPS 10mm
12EXPS 12mm
15EXPS 15mm
20EXPS 20mm
25EXPS 25mm
30EXPS 30mm
Width 10mm 12mm 15mm
100mm 10EXP100 12EXP100 15EXP100
125mm 10EXP125 12EXP125 15EXP125
150mm 10EXP150 12EXP150 15EXP150
175mm 10EXP175 12EXP175 15EXP175
200mm 10EXP200 12EXP200 15EXP200
225mm 10EXP225 12EXP225 15EXP225
250mm 10EXP250 12EXP250 15EXP250
Width 20mm 25mm
100mm 20EXP100 25EXP100
125mm 20EXP125 25EXP125
150mm 20EXP150 25EXP150
175mm 20EXP175 25EXP175
200mm 20EXP200 25EXP200
225mm 20EXP225 25EXP225
250mm 20EXP250 25EXP250
Code Thickness
HDFS10 10mm
HDFS15 15mm
HDFS20 20mm
HDFS25 25mm
Code description unit
CONTACT Contact glue 1 ltr
CONTACT/5 Contact glue 5 ltr
Telephone 0870 24 24 234 Fax 0870 24 03 61318 Anchor Bay 2005
Made from extruded PVC and used to
induce controlled cracking in concrete
slabs. Can be left in place omitting the
use of a joint sealant.
Used in the same application as one part
crack inducer but where the top section
can be removed after concrete has
cured to leave a void for sealant
10mm x 25mm.
Used to induce a controlled crack from
the underside of slabs. Can be used
in conjunction with either top crack
inducers or saw cutting.
A rigid reusable aluminium T-section used
to form a straight void in wet concrete to
accept top crack inducers.
A reusable rigid PVC void former used
in conjunction with fibre boards to create
a grove in wet concrete prior to sealing
with joint sealant.
Crack inducers and void formers
One part top crack inducer
Two part top crack inducer
Bottom crack inducer
Aluminium T-bar
Void formers
Code Size Pack
CI50 10mm x 50mm 5m
CI75 10mm x 75mm 5m
Code Size Pack
CI50/10 10mm x 50mm 5m
CI75/10 10mm x 75mm 5m
Code Size Pack
CY40 40mm 5m
CY75 75mm 5m
Code Size Pack
TB50 50mm 5m
TB75 75mm 5m
Code Size Pack
VH20 20mm x 10mm 3m
VF20 20mm x 20mm 3m
VH25 25mm x 12mm 3m
VF25 25mm x 25mm 3m
Telephone 0870 24 24 234 Fax 0870 24 03 613 Anchor Bay 2005 19
Code Size
CMG205 210ltr
CMG25 25ltr
Code Size
CM75/205 210ltr
CM75/25 25ltr
Code Size
CM90A/210 210ltr
CM90A/25 25ltr
Code Size
CM90R/210 210ltr
CM90R/25 25ltr
Surface treatment chemicals
Curing agent (standard)
Curing agent (75% efficienty)
Curing agent (90% aluminised)
Curing agent (90% efficienty)
A spray applied acqueous solution of
blended silicates designed to prevent
early drying out which enables the
cement to hydrate more efficiently,
considerably reducing the risk of surface
crazing and shrinkage whilst also giving a
stronger, more durable surface.
Coverage: 5.5-6m2/litre
A spray applied resin curing membrane
used to protect freshly placed or
formwork cast concrete from excessive
water loss during the critical curing period
and should be applied as quickly as
possible to ensure maximum benefit.
Coverage: 5m2/litre
A resin based curing membrane which
contains aluminium flakes which when
sprayed on the concrete surface
produces a metallic ‘mirror’ surface to
reflect away solar heat, this is particularly
advantageous on large expanses of
concrete such as airport runways and
concrete roadways.
Coverage: 5.5 m2/litre
A 90% efficiently resin based curing
agent which prevents premature drying
out of the concrete surface thus reducing
the risk of surface cracking.
Telephone 0870 24 24 234 Fax 0870 24 03 61320 Anchor Bay 2005
Dustproof hardener
Bitumen emulsion
RIW L.A.C
RIW Flexiseal
RIW Toughseal
Surface treatment chemicals cont.
A solution used as a treatment on new
old concrete to give a superior surface
resistance to abrasion and cracking
attack with the added bonus of dust
reduction. Coverage: 6 m2/litre approx.
A cold applied rubberised bitumen
emulsion used as a protective damp
proof membrane to concrete and
brickwork. For best results two coats is
recommended. Coverage: 1.1-1.7m2/
litre per coat.
A spirit based bitumen emulsion used
as a water and water-vapour proof
membrane for foundation walls, floor
slabs etc. Coverage: 1m2/litre (2 coats).
1.25 m2/litre (steelwork) (2 coats)
A solvent free thixotropic liquid based on
urethane pre-polymers which on contact
with atmospheric moisture, cures to give
a continuous tough rubber like coating.
The material is supplied in the form of a
blue base coat and a black top coat.
Coverage: Base and top 1m2/kg
(2 coats). Primer 8m2/litre (1 coat)
A polymer modified epoxide coating
supplied as a two part pack of base and
hardener which cures to form a tough
black water and waterproof coating.
Coverage: 4m2/litre per coat.
Code Size
DPH205 210ltr
DPH25 25ltr
Code Size
BE205 210ltr
BE25 25ltr
Code Size
RIW205 205ltr
RIW25 25ltr
Code Description
FLEX/BB5 Blue base 5ltr
FLEX/BB25 Blue base 25ltr
FLEX/BT5 Black top 5ltr
FLEX/BT25 Black top 25ltr
FLEX/PR5 Primer 5ltr
FLEX/PR25 Primer 25ltr
Code Size
TOUGH/5 5ltr
TOUGH/20 20ltr
Telephone 0870 24 24 234 Fax 0870 24 03 613 Anchor Bay 2005 21
Fosroc – waterproofing membranes
Proofex 3000
Proofex engage
Proofex engage detail strip
Proofex lm
A high performance self adhesive
membrane for a range of waterproofing
applications including basements and
substructures. Proofex 3000 provides a
vapour and waterproofing membrane to
water excluding structures and protects
concrete from attack by aggressive
ground salts.
Roll size: 1m x 20m
Is a unique patented system comprising
a complex cell mesh bonded to a
polyethylene membrane which allows
poured concrete to interlock with
the membrane forming a tenacious
mechanical bond. Proofex engage is
supplied with a selvedge on one side to
provide sealed laps.
Roll size: 1.27m x 30m
A reinforced, double sided waterproofing
adhesive tape for sealing and jointing
roll ends, cut edges corner pieces, sold
in packs of two. It consists of a strong
synthetic fibre fabric impregnated and
coated both sides with a bitumen rubber
adhesive. Each side of the tape is
protected by a removable
siliconised paper.
Roll size: 200mm x 10m
Is a two component applied liquid
membrane for sealing around intricate
details such as pipe entries penetrations,
pile caps, etc. Coverage: approximately
4-6kg/m2 at normal loadings,
approximately 8kg/m2 where standing
water and pressurised water occur.
Code Description
WPM Proofex 3000
WPM/PR05 Proofex primer 5ltr
WPM/PR25 Proofex primer 25ltr
Code Description
PROF/ENG Proofex engage
Code Description
PROF/STRIP Proofex engage
detail strip
Code Description
PROOF/LM Proofex lm
PROOF/MESH Proofex lm mesh
50m x 100mm
Telephone 0870 24 24 234 Fax 0870 24 03 61322 Anchor Bay 2005
Waterstops – Fosroc range
Supercast rearguard S250
Supercast rearguard S250 junctions
Supercast hydrofoil 250
When used on ground slabs where the
waterstop is supported on blinding,
Rearguard profiles usually require no
fixing. The waterstop is layed centrally
over the line of the joint to be formed.
Fixing to vertical shuttering is done by
nailing through the outer nailing flanges
leaving the head of the nail proud so
that it is held in the cured concrete. This
prevents the waterstop being displaced
when the shuttering is struck.
Roll size: 12 metre
A range of junctions for use with
supercast rearguard S250. Centre
bulb selections are used in expansion,
contraction joints.
The centre bulb allows for movements
in a structure to be accommodated
whilst its hexagonal design provides a
flat surface. This allows shuttering and
joint fillers to fit snugly. All centrally placed
supercast waterstops incorporate an
eyeletted, reinforced edge flange. This
enables them to be easily positioned by
wiring to surrounding reinforcement.
Roll size: 12 metre
Code Size
REAR/250 12m
Code Description
R250/FM Flat mitre
R250/F3W 3 way on flat
R250/F4W 4 way on flat
R250/INT90 Internal 90°
R250/EXT90 External 90°
Code Size
HYDRO/250 12m
Telephone 0870 24 24 234 Fax 0870 24 03 613 Anchor Bay 2005 23
A range of junctions used with
Supercast hydrofoil 250.
Jigs and knife used for on site
welding of supercast rearguard
250 and hydrofoil 250.
Integral sealing for construction joints
in concrete cast in-situ. Convenient and
problem solving in-situations where a
conventional waterstop would require
complex shuttering. Typical uses include
secant piled and diaphragm walled
basements, pile caps and casting against
old concrete.
Roll size: 15 metre
Waterstops – Fosroc range cont.
Supercast hydrofoil 250 junctions
Jig and knife
Supercast SW10
Code Description
S250/FM Flat mitre
S250/F3W 3 way on flat
S250/F4W 4 way on flat
S250/MOE Mitre on edge
250/TP T piece
Code Description
KNIFE 110v hot knife
JIG/REAR Rearguard jig
JIG/HYDR Hydrofoil jig
Code Description
SCAST/SW10 5mm x 20mm x 15m
Telephone 0870 24 24 234 Fax 0870 24 03 61324 Anchor Bay 2005
Fosroc joint sealants
One part polysulphide
Two part polysulphide
Polysulphide primer
Two part polyurethane
Thioflex one is a one part, gun applied moisture
activated, polysulphide sealant. It is ideal for sealing
joints in window and door frame surrounds and as a
capping forbeaded glazing systems.
Conforms to BS 5215: 1986.
Cartridge size: 380mls
Colours: black, buff, mahogany, grey, stone,
cement white, white, brick red.
Thioflex 600 is available in gun and pouring grades.
The gun grade is ideal for general application, and is
available in a range of colours. It is packed in a ready
to mix 2.5 litre tin containing the base and curing agent
in the correct proportions. The pour grade for joints
in horizontal surfaces is supplied in grey only in 5 litre
packs with the base and curing agent in separate tins.
Conforms to BS 4254: 983, BS 6920:1996
Fosroc primer 7 is a one part chemically active
clear liquid for brush application to concrete, stone,
brickwork, timber and unglazed edges of
ceramic tiles prior to applying thioflex sealants.
Fosroc colpor 200PF is a high performance, pitch
free, pavement joint sealant. Used for the sealing and
maintenance of joints in concrete roads, concrete
runways and hardstandings. Colpor 200 PF is
particularly suitable for sealing areas where fuel and oil
spillage might occur such as aircraft fuelling areas, oil
terminals, garage forecourts, parking and cargo areas.
Conforms to BS 5212: 1990-types n, f and f b.
Colour: black
Code Pack
THIO/1 380mls
Code Pack
THIO/600G 2.5 Litre
THIO/600 5.0 Litre
Code Pack £/each
THIO/PR 500ml £12.28
Code Pack
COLPOR200 5 litre
Telephone 0870 24 24 234 Fax 0870 24 03 613 Anchor Bay 2005 25
Fosroc joint sealants cont.
Hot poured sealant
Foam backer rods
Accessories
Fosroc pliastic is a hot-poured rubber
bitumen horizontal joint sealant. Used for
sealing movement and construction joints
in pavements, floor slabs, water retaining
and water excluding structures.
Colour: black
Conforms to BS 2499: 1993 – pliastic N2
Yield: 19.6 Litre per pack
A closed cell polyethylene foam cord
used as a packing material for
joint sealants.
Tools and accessories used in the
application of joint sealing materials.
Mixing paddle: used for mixing sealants
Barrel gun: used for the placement of
bulk fill sealants. Supplied with three
different size nozzles.
Follower plate: designed to assist the
filling of barrel guns.
Cleaning solvent: a solvent based liquid
used for cleaning tools and barrel guns.
Gloves: a pvc knitted wrist glove
Bond breaking tape: used as a bond
breaker between joint sealant and
fibreboard. 25mm x 50m roll.
Code Pack
HPS20 20kg
Code Size Pack
BR6 6mm 1500m
BR10 10mm 1100m
BR12 12mm 900m
BR15 15mm 500m
BR20 20mm 300m
BR25 25mm 200m
BR30 30mm 150m
BR40 40mm 80m
BR50 50mm 50m
Code Pack
PADDLE Each
B/GUN Each
F/PLATE each
SOLV/5 5 litre
GLOVE 12 no.
B/TAPE 2550m
Telephone 0870 24 24 234 Fax 0870 24 03 61326 Anchor Bay 2005
Grace – waterproofing membranes
Bituthene 3000
Bituthene 4000
Bituthene 8000
Bituthene liquid membrane
A self-adhesive, rubberized asphalt/
polyethylene waterproofing membrane.
Ideal for waterproofing concrete decks.
Roll size: 0.9m x 20m
A self-adhesive hdpe waterproofing
membrane. Its cross laminated, high
density polyethylene carrier film provides
high tear strength and puncture and
impact resistance.
Roll size: 0.9m x 20m
Bituthene 8000 combines the proven
bituthene adhesive technology with a
unique, grey coloured carrier film to
provide superior performance and easier
installation. It can be used horizontally or
vertically to protect basements and other
critical sub structures from the effects of
water, damp and gas.
Roll size: 1m x 20m
A two component, elastomeric, liquid
applied detailing compound for use with
grace waterproofing membranes.
Size: 5.7ltr
Code Description
B3000 Bituthene 3000
B1/PR05 B1 primer 5ltr
B1/PR25 B1 primer 25ltr
Code Description
B4000 Bituthene 4000
B2/PR05 B2 primer 5ltr
B2/PR25 B2 primer 25ltr
Code Description
B8000 Bituthene 8000
B2/PR05 B2 primer 5ltr
B2/PR25 B2 primer 25ltr
Code Description
BITU/LM Bituthene lm
Telephone 0870 24 24 234 Fax 0870 24 03 613 Anchor Bay 2005 27
Grace – waterproofing membranes cont.
Servipak protection board
Preprufe 300R and 160R
Preprufe tape
Durable, lightweight boards for
permanent protection of waterproofing
membranes from abrasive backfill, site
trafficking and reinforcement fixing.
Supplied in 3mm and 6mm thick sheets.
Sheet size: 2m x 1m
Is a pre-applied waterproofing membrane
that bond integrally to poured concrete
for use below slabs or behind basement
walls on confined sites.
Preprufe 300R is a heavy duty grade
for use below slabs and on rafts.
Designed to accept the placing of
heavy reinforcement using conventional
concrete spacers.
Preprufe 160R is a thinner grade for
lighter applications and blindside, zero
property line applications against soil
retention systems.
Roll size: Preprufe 300R 1.2m x 30m
Preprufe 160R 1.2m x 35m
Used for covering cut edges, roll ends,
penetrations and detailing.
Roll size: 100mm x 15m
Code Description
S/PAK03 3mm servipak
S/PAK06 6mm servipak
Code Description
PRE300R Preprufe 300R
PRE160R Preprufe 160R
Code Description
PRE/TAPE Preprufe tape
Telephone 0870 24 24 234 Fax 0870 24 03 61328 Anchor Bay 2005
Waterstop – grace servicised range
Serviseal
Servitite
AT system
Jig and knife
Servistrip AH 205
An external PVC waterstop system
for passive protection of expansion,
construction and contraction joints in
reinforced concrete structures.
A high performance, internal PVC
waterstop for passive protection of critical
joints in reinforced concrete structures.
A high performance PVC waterstop
system with co-extruded hydrophilic
bulbs to provide a unique combination
of active and passive protection for joints
in concrete.
Jig and knife used for the on site welding
of waterstops
A solid, active jointing strip which swells
when exposed to water to prevent leak
paths in concrete.
Roll size: 20mm x 5mm x 10m
Code Description/size
SS195 Serviseal 195
SS240 Serviseal 240
SS320 Serviseal 320
Code Description/size
ST150 Std XJ 150mm
ST230 Std XJ 230mm
ST305 Std XJ 305mm
Code Size
AT200 200mm x
AT240 240mm x
Code Description
KNIFE 110v hot knife
JIG Jig
Code Description
AH205 Servistrip AH 205
Telephone 0870 24 24 234 Fax 0870 24 03 613 Anchor Bay 2005 29
Cetco – waterproofing system
Volclay voltex
Voltex accessories
Volclay granules
Volclay RX101 waterstop
Voltex is a highly effective waterproofing
composite of high strength geotextile and
4.88kg of sodium bentonite per square
metre. A patented needle-punch process
interlocks the geotextiles together
forming an extremely strong composite
that maintains the equal coverage of
bentonite, as well as protects it from
inclement weather and construction
related damage. Once backfilled,
voltex hydrates and forms a monolithic
waterproofing membrane. Voltex contains
zero voc, can be installed in almost any
weather condition to green concrete.
Roll size: 5.0m x 1.1m
Voltex nails and soft washers allows
direct shot-fired applications to secant
and contiguous piling, steel sheet piling,
diaphgregm wall, skin wall cast in-situ
and under blinding.
Pack size: 150
Stapler & staples used to secure laps
on sand or concrete underlining, or to
complement shot-fired fixings.
Pack size: 2500
Volclay granules are used to fill
cavities and voids in the substrate
prior to installing the main bentonite
waterproofing course. It is also used to
seal around slab penetrations to form a
continuous waterproofing system.
Pack size: 20kg
Waterstop RX101 is a sodium bentonite
based waterstop designed to stop water
infiltration through cast-in place concrete
construction joints by expanding upon
contact with water to form a positive seal
against the concrete.
Roll size: 5 metre
Code Description
VOLTEX Volclay voltex
Code Description
VOL/NAIL Voltex nails
Code Description
VOL/STPLR Stapler
VOL/STAP Staples
Code Description
VOL/GRAN Volclay granules
Code Description
RX101 Volclay rx101
REVOFIX Revofix 30m
RXWB RX WB adhesive
Telephone 0870 24 24 234 Fax 0870 24 03 61330 Anchor Bay 2005
Fosroc concrete repair
Renderoc GP
Renderoc FC
Renderoc HB
Is a general purpose concrete
reinstatement mortar which can be used
as a render as well as for all types of
patch repairs. Renderoc GP is alkaline in
nature and will protect embedded steel
reinforcement. Renderoc GP is designed
for vertical, overhead or horizontal
applications. It can be applied up to
20mm thickness in sections overhead
and 30mm thickness in vertical sections.
Coverage: 16 litres/25kg bag
1.6m2 at 10mm thickness
Is designed for application in thin layers
to produce a fair-faced appearance
to concrete surfaces in readiness to
receive a protective/decorative coating.
Renderoc FC is designed for vertical and
overhead use to infill honeycombing and
voids up to 3mm deep in the surface of
concrete.
Coverage: 15 litres/25kg bag
5.0m2 at 3mm thickness
For the reinstatement of large areas
of concrete and for small, localised
patch repairs. Renderoc HB is alkaline
in nature and will protect embedded
steel reinforcement it is specifically
designed for vertical and overhead
high-build applications. Renderoc HB
can be applied in sections up to 80mm
thickness in vertical locations and up to
50mm thickness in overhead locations
in a single application and without the
use of formwork. Coverage: 14.5-15.0
litres/18kg 15m2 at 10mm thickness
Code Size
REN/GP 25kg
Code Size
REN/FC 25kg
Code Size
REN/HB 18kg
Telephone 0870 24 24 234 Fax 0870 24 03 613 Anchor Bay 2005 31
Code Colour Size
FAS/GR25G Grey 25kg
FAS/GR Grey 8kg
FAS/GR/25W White 25kg
FAS/WH White 8kg
Code Size
FIL/RUB25 25kg
Code Size
SBR05 5 litre
SBR25 25 litre
Code Size
PVA05 5 litre
PVA25 25 litre
Code Description
PADDLE Mixing paddle
C/STONE Carborundum stone
P/FLOAT Plastic float
W/FLOAT Wooden float
M/FLOAT Metal float
BUCKET Site pvc bucket
GLOVE PVC knit wrist gloves
BRUSH Turks head brush
Concrete repair
Fastpatch cement
Fill ‘n’ rub
SBR bonding agent
PVA bonding agent
Ancillary products
A prepacked specialised repair cement,
based on the latest polymer cement
technology, it provides a simple, cost
effective rapid repair system for in-situ
and precast concrete, masonry, screeds,
renders, brickwork and blockwork.
Colours: grey and white. Coverage: 1kg
yields 500cm3 or 2.1kg/mm/m2
A convenient method of filling blow holes
and small surface defects in precast
or in-situ cast concretes, as well as
providing an even standardised colour
and aesthetic finish.
Is a styrene butadiene emulsion for
use as an admixture in cementitious
compounds. It will improve many of the
properties of the compound such as
improving strength, excellent adhesion,
wear resistance, waterproof and weather
resistance and shrinkage. Full technical
details available on request.
A versatile and non-toxic ready to use
PVA bonding and sealing adhesive giving
a strong but flexible bond with high
moisture and mould resistance. Typical
uses: priming, woodworking, concreting,
floor laying, plastering and rendering,
tiling, painting and decorating.
A range of products for the use with
concrete repair products.
Telephone 0870 24 24 234 Fax 0870 24 03 61332 Anchor Bay 2005
Formwork tie rod system
Formwork tie rod
Wing nuts
Waler plates
Tie rod connectors
Water barrier connectors
Rock anchor
A self cleaning high tensile steel tie rod
designed for use with formwork. Available
in 15mm and 20mm diameters.
Used in conjunction with waler plates to
secure tie rods in formwork.
A high quality pressed plate used in
conjunction with tie rods and wing nuts
to secure formwork.
Dimensions: 100 x 100 x 10mm to suit
15mm tie rod 120 x 120 x 20mm to suit
20mm tie rod.
A jointing nut used to connect two
tie rods together with a centre stop
to ensure equal spacing inside the
connector. Length: 105mm
Used in water retaining structures.
Cast into the concrete wall between
two separate tie rods. After pouring
tier rods are removed and water barrier
remains in-situ.
Used for securing single sided formwork
in concrete or rock walls.
(37Mm drill bit)
Code length
TB15 6.0M
TB15/1.5 1.5M
TB15/1.2 1.2M
TB15/3 3.0M
TB20 6.0M
Code Size
WN15 15mm
WN20 20mm
Code Size
WP15 15mm
WP20 20mm
Code Size
JN15 15mm
Code Size
WB15 15mm
WB20 20mm
Code Size
RA15 15mm
Telephone 0870 24 24 234 Fax 0870 24 03 613 Anchor Bay 2005 33
Formwork tie rod system cont.
Cast in anchor
Weldable anchor
Tie rod sleeve
Tie sleeve cones
Flupps
Tie plug cement
Wedge anchors
A plastic cast in anchor which is secured
to formwork and cast into initial pour
to provide an anchor for tie rod in
subsequent pours.
An anchor which can be welded to
structural steel beams ,sheet piling
and other metal structures to accept
15mm tie rod. Anchors must be welded
continuously all the way round – load
tests should be conducted before use.
A rigid pvc tube used as a spacer
between formwork and also allows tie rod
to be removed easily.
A pvc cone used on both ends of tie rod
sleeves which can be easily removed
after formwork is struck.
Used in conjunction with tie plug cement
to give a water tight seal in areas where
tie rod’s have been removed.
A cement specially developed for
plugging and waterproofing of tie holes
in concrete walls.
A m16 x 65mm drop in anchor used for
anchoring props in concrete.
Code Size
C/ANCHOR 15mm
Code Size
WELD/ANCHOR 15mm
Code Size Pack
T22 22/26mm 100m
T26 26/30mm 50m
Code Size Pack
BC22 22mm 500
BC26 26mm 500
BC22/50 22/50mm 125
BC26/50 26/50mm 125
BC/TOOL 1
Code Size Pack
FLUPP 22mm 500
FLUPP26 26mm 250
FLUPP32 32mm 125
Code Pack
TP8 8kg
Code Description Pack
WEDGE M16 x 65mm 25
Telephone 0870 24 24 234 Fax 0870 24 03 61334 Anchor Bay 2005
Formwork accessories
Plastic corner fillets
Wooden corner fillets
Formwork magnets
Formwork tape
Grout check foam
An extruded rigid pvc section which can
be nailed to formwork or column shutters
to form chamfered corners. Supplied with
or without nailing flange.
A wooden section which can be nailed
to formwork or column shutters to form
chamfered corners.
A magnet used for removing wire and
nails from shutters prior to concreting.
A pvc tape used for the sealing of joints in
formwork to prevent grout loss. Roll size
50mm x 33m
Designed for use on all types of
formwork. Grout check foam is a closed
cell polyethylene foam with a high
pressure adhesive on one side used for
sealing joints in formwork to prevent grout
loss. Available in two sizes:
6mm x 12mm x 10m.
12mm x 24mm x 5m.
Code Size Pack
CF11 11mm 100m
CFN11 11mm 100m
CF15 15mm 100m
CFN15 15mm 100m
CF20 20mm 100m
CFN20 20mm 100m
CF25 25mm 100m
CFN25 25mm 50m
CF30 30mm 50m
CFN30 30mm 50m
Code Size Pack
CF20W 20mm 100m
CF25W 25mm 100m
Code Pack
MAGNET 2
Code Pack
FTR50 30 rolls
Code Size Pack
6F12 6 x 12mm 25 no.
12F24 12 x 24mm 12 no.
Telephone 0870 24 24 234 Fax 0870 24 03 613 Anchor Bay 2005 35
Formwork accessories cont.
Silicone sealant
Handy foam
Fire retardant handy foam
Bright round wire nails
Formwork plugs
Steel adjustable kickers
Plastic kickers
A clear high modulus silicone sealant
in 310mls which can be used for filling
movement joints in formwork.
An aerosol packed polyurethane foam
which expands when released used
for filling gaps in formwork and other
construction areas.
A fire retardant aerosol packed
polyurethane foam which prevents the
transmission of smoke, seals around
pipework, insulates against noise, heat or
cold. Conforms to din 4102 part 1 class
b1. CFC free.
A high quality bright round wire nail.
Supplied in 20kg boxes.
A plastic conical shaped plug used for
the filling of redundant tie holes in timber
shutters.
Designed to eliminate the need to pour
a kicker.
Code Pack
S/310 25
SKELG 1
Code Pack
FHP750 12
Code Pack
FRF750 12
Code Size Pack
NAIL/50 50mm 20kg
NAIL/65 65mm 20kg
NAIL/75 75mm 20kg
NAIL/100 100mm 20kg
NAIL/150 150mm 20kg
Code Size Pack
F/PLUG11 11mm 1000
F/PLUG20 20mm 1000
F/PLUG22 22mm 1000
F/PLUG26 26mm 1000
Code Size Pack
KICK/150 150mm 100
KICK/175 175mm 100
KICK/200 200mm 100
KICK/225 225mm 100
KICK/250 250mm 100
Code Description Pack
P/KICKER Plastic kicker 100
Plastic formwork kickers are used to secure
formwork at the base of walls. They are
supplied with a masonry nail which can be
placed with the aid of a hilti gun.
Telephone 0870 24 24 234 Fax 0870 24 03 61336 Anchor Bay 2005
Formwork chemicals
Mould oil
Chemical release agent
Surface retarder
Formwax sealer
A general purpose mould oil with good
release qualities. For use on all types
of formwork. Can be brush or sprayed
applied.
A general purpose chemical release
agent which provides excellent release
and surface finish. Reduces blowholes,
staining and surface blemishes.
Mould applied (code SRG25) brushed
onto formwork, it is designed to give
an exposed aggregate surface which
gives an excellent key for subsequent
concreting. Surface applied (code
SRS25) sprayed onto fresh concrete to
give an exposed aggregate finish.
Formwax is specifically developed for
the initial sealing of various formwork
surfaces. Based on crystalline waxes and
with a fugitive dye which will not stain
permanently, this thixotropic material
when worked into a surface takes on
a smooth, thin paste consistency. Its
economy of use, speed of application
and compatibility with most types
of release agent make it the ideal
preservation sealer.
Coverage: 10m2/kg approx.
Code Size
MO205 205
MO25 25
Code Size
CRA205 205
CRA25 25
Code Size
SRG25 25
SRS25 25
SRS205 205
Code Size
FW20 20kg
Telephone 0870 24 24 234 Fax 0870 24 03 613 Anchor Bay 2005 37
Formwork chemicals cont.
Shutter repair compound
Formwork plugs
Sprayers
Barrel accessories
A quick setting two part polyester filler
used for filling holes and damaged areas
on wood, fibreglass or metal formwork.
It is easily worked and sanded and is
compatible with release agents.
A plastic conical shaped plug used
for the filling of redundant tie holes
in timber shutters.
High performance sprayer units for the
application of mould oil and chemical
release agent.
Taps and pumps used in conjunction with
plastic and metal barrels.
Code Size
SFO8 8kg
SFH1 Each
Code Size Pack
F/PLUG11 11mm 1000
F/PLUG20 20mm 1000
F/PLUG22 22mm 1000
F/PLUG26 26mm 1000
Code Description
MS08/S 8ltr metal sprayer
PS08 8ltr plastic sprayer
KN20 20ltr knapsack
NOZZ Nozzle
LANCE Sprayer lance
TRIGGER Sprayer trigger unit
GASK/M Metal gasket set
GASK/P Plastic gasket set
SOLV/5 Cleaning solvent 5ltr
SOLV/25 Cleaning solvent 25ltr
Code Description
TAP 3/4’’ barrel tap
PUMP Barrel pump
Telephone 0870 24 24 234 Fax 0870 24 03 61338 Anchor Bay 2005
Monotub formwork systems
Monotub
Monotub accessories
Is a disposable formwork for rapid
construction of circular and square
concrete columns.
Advantages:
• Fast and economical to use
• 100% water resistant and can be
stored outside without damaging the
quality of the tube.
• Light and easy to handle.
• Quick and easy to erect
• Provides the optimum fair face finish
concrete column.
• Requires no mould oils or release
agents.
• Stripped literally in seconds.
• Very strong
• Can be used for horizontal void
forming. Manufactured in a large range
of sizes.
• Delivered at short notice.
(Popular sizes typically 24/48 hours)
Products used to assist with the erection
of monotub tubes.
Code Diameter
MONO150 150mm
MONO200 200mm
MONO240 240mm
MONO250 250mm
MONO300 300mm
MONO350 350mm
MONO400 400mm
MONO450 450mm
MONO500 500mm
MONO550 550mm
MONO600 600mm
MONO650 650mm
MONO700 700mm
MONO800 800mm
MONO900 900mm
MONO1000 1000mm
MONO1200 1200mm
Code Dimension
MONO/200S 200mm x 200mm
MONO/250S 250mm x 250mm
MONO/300S 300mm x 300mm
MONO/350S 350mm x 350mm
MONO/400S 400mm x 400mm
Code Details
M/STRAP Multistrap
MONO/KICK Kicker
Telephone 0870 24 24 234 Fax 0870 24 03 613 Anchor Bay 2005 39
Code Thickness
CLAY/50 50mm
CLAY /75 75mm
CLAY/100 100mm
CLAY/125 125mm
CLAY/150 150mm
CLAY/175 175mm
Code Thickness
CLAY/60 60mm
CLAY/85 85mm
CLAY/110 110mm
CLAY/160 160mm
Code Description
25POLY 25mm polystyrene
50POLY 50mm polystyrene
100 POLY 100mm polystyrene
Formwork systems
Claymaster
Cellcore
Clayboard
Polystyrene sheets
Is a low density expanded polystyrene,
designed to compress under load and
so reduce the lateral forces of ground
movement on the foundation.
Sheet size: 2.4m x 1.2m.
Thickness: 50mm-300mm
Consists of a honeycomb of inter-
locking sections made from expanded
polystyrene. Designed so as ground
movement occurs cellcore compresses
and buckles to accommodate it, thereby
reducing the forces that would otherwise
be transmitted to the foundations. It
is used extensively in both residential
and commercial applications to protect
piled beams and rafts, heavy slabs and
reinforced ground floor slabs.
Sheet size: 2.44m x 1.22m.
Grades: CC & CP full technical
information available on request.
Is a unique, environmentally friendly void
former and foundation stabiliser made
from a biodegradable honeycomb core
set between lightweight polypropylene
facings. When dry clayboard is strong
enough to support the weight of wet
concrete and steel reinforcement.
Sheet size: 2.440m x 1.0m. Full
technical information available on request.
A SDN grade expanded polystyrene
board used to as thermal insulation and
void former in walls and ground floor
slabs. Can be cut accurately with the aid
of a fine tooth saw to any shape or size.
Sheet size: 2.44m x 1.2m (8’ x 4’).
Other thickness available on request
Telephone 0870 24 24 234 Fax 0870 24 03 61340 Anchor Bay 2005
Kwikastrip continuity system
The Kwikastrip reinforcement continuity
system has been fi rmly established
over many years as the contractor’s
fi rst choice. This results from consistent
delivery of an almost infi nitely variable
product within a very short lead-time.
To further reassure engineers, Kwikastrip
is supported by the highest level of
technical endorsement in the form of
UK CARES Technical Approval.
Telephone 0870 24 24 234 Fax 0870 24 03 613 Anchor Bay 2005 41
Halfen HDB punching shear reinforcement
Halfen HDB punching shear reinforcement
is designed to prevent punching failure
at column heads in concrete flat slab
construction – without the traditional
need for downstand beams, mushroom-
headed columns and thickened floors.
The system is manufactured from ribbed bars
which are hot-forged to make double-ended
studs (connected by spacer rails) to provide
virtually slip-free shear head reinforcement
with excellent anchorage. The two or three-
stud elements are simply dropped into place
in the reinforcing cage and retained in position
by means of clip bars and/or tying wire. This
typically reduces site installation time from hours
to minutes per column head compared
to traditional bent reinforcement.
To facilitate selection and use, a specially-written
software programme that calculates shear stress
and reinforcement requirements is available.
The HIT System is the latest development in
thermal break and reinforcement continuity
for cantilevered balcony construction.
HIT helps to eliminate the effects of cold
bridging (i.e. condensation and mould
growth) experienced with reinforcement
that is traditionally continuous from internal
slab straight through to external balcony.
The HIT System comprises special stainless
steel swaged couplings in the tension zone
(into which is factory-fitted normal high-
yield reinforcement) and stainless steel
double-headed studs in the compression
zone. These stainless steel components
are housed in a high-density polystyrene
fabrication which provides the thermal
separation between floor slab and balcony.
The HIT System is supplied in versions
for in-situ and precast applications and
modules of 1.0m and 0.2 metres that can
be used in combination to avoid cutting.
Halfen HDB Punching Shear Reinforcement
Halfen HIT Insulated Balcony Connection System
Telephone 0870 24 24 234 Fax 0870 24 03 61342 Anchor Bay 2005
Formrib and rebar couplers
Formrib permanent shuttering
MBT couplers
Halfen HBM couplers
A galvanised expanded metal used
widely in the construction industry as a
permanent shuttering for stopends. It
is manufactured from hot-dipped zinc
coated steel sheet to BS EN 10142
1991. Sheet size: 3m x 0.445m
The MBT range of couplers provides
a cost effective method of joining
reinforcing bars particularly when the
fixed bar is already in place. They can
be installed without any preparation to
the bar ends and without any need to
rotate bars.
The HBM system consists of high-
strength couplers factory-swaged onto
grade 500 high-yield reinforcement bars.
Anchorage reinforcement (female socket
bars) can be supplied in shapes and
lengths to suit almost any application
configuration. The male connection bar
has a hot-forged ‘upset’ end onto which
is rolled a standard metric thread.
HBM is hallmarked by off-the-
shelf availability and CARES
Technical Approval.
Code Description
FORMRIB/3 3m x 0.445m
Code To suit rebar
MBT10 T10
MBT12 T12
MBT16 T16
MBT20 T20
MBT32 T32
MBT40 T40
Bar diameter 10mm 12mm 16mm 20mm 25mm 32mm 40mm
External diameter d 33.4 33.4 42.2 48.3 54 71 81
Total length l 100 140 160 204 258 312 484
Socket size A/F (ins) 1/2 1/2 1/2 1/2 5/8 5/8 3/4
No. of bolts 4 6 6 8 8 10 14
Approx. weight (kg) 0.52 0.72 1.25 1.96 3 6.5 11.3
Telephone 0870 24 24 234 Fax 0870 24 03 613 Anchor Bay 2005 43
Concrete finishing tools
Easy float (fresno)
Easy float handle
Concrete rake
Concrete finishing brush
Hand floats
Tamping beam
Carborundum stone
A zinc plated steel float incorporating
radius arms and a texturing broom for
brush work. The broom is a polybristle
medium texture. Floats have radius ends
to prevent lap marks.
Size: 1200mm (4ft).
An aluminium snap extension handle
used in conjunction with easy floats.
Size: 1800mm (6ft)
The tools are lightweight and of rugged
construction and are designed to
allow the placement of concrete where
required. The tooth side is for raking
and the smooth side is for floating
and screeding.
Primarily used for concrete texturing on
motorways, airport aprons and taxiways.
A range of floats used for the placing and
floating of concrete.
An aluminium box section beam used for
tamping and levelling concrete. Supplied
either with or without handles.
Length: 6000mm. Other lengths
available on request.
A carborundum rubbing block used
to smoothen out uneven concrete
repaired surfaces.
Code Description
E/FLOAT1200 1200mm fresno
Code Description
E/HANDLE Handle 1800mm
Code Description
C/RAKE Concrete rake
Code Description
F/BRUSH600 600mm wide
F/BRUSH900 900mm wide
Code Description
P/FLOAT Plastic float
M/FLOAT Metal float
W/FLOAT Wooden float
Code Description
T/HANDLE Handles
Code Description
C/STONE Carborundum stone
Telephone 0870 24 24 234 Fax 0870 24 03 61344 Anchor Bay 2005
Concrete test equipment
Cube moulds
Curing tank
Slump cone
Scoop
Wire brush
Max/min thermometer
A high quality four part design cube
mould with meets requirements of
BS1881 part 108, EN12390-1 and
ISO1920
A curing tank which can take up to
30 x 150mm cube moulds, made from
polyethylene and measuring 990mm x
686mm x 635mm overall. Fitted with a
220 volt 3kw heater but also works on
110 volt (heating taking a little longer)
fitted with mechanical thermostat and
a galvanised mesh lower rack. The
thermostat is factory set to control the
tank at 20°C. It is ideal for site use where
an economical solution is required. Meets
standard BS 1881 part 111 EN 12390-2.
Designed to measure the workability of
concrete. This is carried out by filing the
slump cone with fresh concrete in three
layers, tamping each one and levelling
to the top of the cone. The slump cone
is then removed and the distance the
concrete falls or ‘slump’ is measured
with the rule.
An aluminium scoop for use with cube
moulds and other test equipment.
A construction duty wire brush.
A quick set push button thermometer for
use on site.
Code Size
CM100 100mm
CM150 150mm
T/BAR Tamp bar
Code Description
C/TANK Curing tank
Code Descritpion
SLC Slump cone
SL/ROD Slump cone rod
B/PLATE Base plate
Code Description
SCOOP Scoop
Code Description
W/BRUSH Wire brush
Code Description
THER Max/min thermometer
Telephone 0870 24 24 234 Fax 0870 24 03 613 Anchor Bay 2005 45
Protection products
Rebar caps
Frost blanket
Hessian
Temporary protective sheeting
Brick acid
Corner fenders
Gloves
Protection sheet
A high visibility safety cap designed to
fit over the end of protruding rebar to
reduce the risk of injury.
A 10mm closed cell polyethylene foam
designed to give good protection to
concrete during low temperatures. They
also make excellent curing mats during
warmer temperatures as well.
Hessian rolls used for the protection and
covering up of masonry and concrete.
A polythene sheeting used for covering
up and protection of building goods
on site.
Is a selected blend of inorganic
acids for the removal of cementitious
contamination and rust from a wide range
of surfaces.
Designed to protect corners on columns
in areas of builds which are prone to
heavy trafficking such as multistorey car
parks. Available with tangs for casting
into concrete or with pre-drilled holes for
surface fixing after the column is cast.
A general purpose knit wrist pvc glove
used for general protection of hands
while handling building materials.
A 2mm corrugated polypropylene sheet
which is easy to cut, crease or curve
to any site requirement. Available in
standard or fire rated grades.
Sheet size: 2.44m x 1.22m (8’ x 4’).
Code Rebar size Pack size
SBP16 6mm-18mm 250
SBP32 16mm-32mm 250
SBP40 25mm-40mm 100
Code Size
FRO/BL 75m x 2m x 10mm
Code Size
HESSIAN 1350mm x 46m
Code Size
HDPS 4m x 25m
Code Description
BRICK/05 Brick acid 5ltr
Code Description
C/FENDER 50mm x 50mm x 1.2m
Code Pack
GLOVE 12 pairs
Code Pack
PS02 Sheet
PS02FR Sheet
Telephone 0870 24 24 234 Fax 0870 24 03 61346 Anchor Bay 2005
Code Description Pack
RIB/100S 100mm stainless 100
RIB/150S 150mm stainless 100
RIB/3000S 3000mm stainless Each
RIB/100G 100mm galv 100
RIB/150G 150mm galv 100
RIB/3000G 3000mm galv Each
Code Description Pack
HTS/B/75S 75mm stainless 100
HTS/B/100S 100mm stainless 100
HTS/B/150S 150mm stainless 100
HTS/B/175S 175mm stainless 100
HTS/B/200S 200mm stainless 100
HTS/B/75G 75mm galv 100
HTS/B/100G 100mm galv 100
HTS/B/150G 150mm galv 100
HTS/B/175G 175mm galv 100
HTS/B/200G 200mm galv 100
Halfen-brick tie products
Ribslot 28/20
HTS-B channel brick ties
HTA and HZA cast in channels
Halfen ribslot 28/20 is a self-anchoring
channel which has been designed to
achieve minimum deflection. It is available
in grade 304 stainless steel (S304) and
a pre galvanised steel. Sizes available:
100mm, 150mm and 3000mm.
Halfen HTS-B channel ties are designed
to bed into the mortar at one end and
have a shouldered head that locates into
a cast-in or surface fixed channel at the
other end available in grade 304 stainless
steel (S304) and a pre galvanised mild
steel. Sizes available: 75mm, 100mm,
150mm, 175mm & 200mm.
A cold rolled channel with anchors
designed for casting into concrete.
The channel with its anchors, is attached
to the formwork before casting. The
void within the channel is filled with
granulated expanded polystyrene which
keeps the inside of the channel free from
concrete during pouring and which is
easily removed when fixings are to be
made. Full technical literature available on
request. Types available: HTA 28/15,
HTA 38/17, HTA 40/25, HZA 41/22.
Standard lengths 3050mm & 6070mm.
Cut lengths available on request.
Grades available: A2 stainless steel and
galvanised mild steel.
Telephone 0870 24 24 234 Fax 0870 24 03 613 Anchor Bay 2005 47
HTS-C cavity brick ties
HTS-W wire ties
HTS-FS frame cramps
Halfen HTS-C cavity ties have been
designed to meet the design and
performance requirements of DD140.
These ties are designed for a normal
10mm mortar bed. HTS-C ties come in
standard shapes and lengths which will
cover most applications.
Grades available: stainless steel grade
304 (S304). Galvanised mild steel.
Halfen HTS-W wire ties are suitable for
cavities up to 100mm. They are available
in stainless steel grade 304 only. HTS-W2
tie meets DD140 type 2 requirements
and complies to DD140 type 4.
Lengths available: 200mm & 225mm
Halfen HTS-FS frame cramps are ties
that bed into the mortar joint at one end
and are surface fixed to the structure
through an upstand at the other end.
HTS-FS frame cramps come in standard
shapes and lengths which will cover
most applications. Available in stainless
steel grade 304 (S304). Sizes: 75mm,
100mm, 125mm, 150mm, 175mm
and 200mm.
Halfen-brick tie products cont.
Telephone 0870 24 24 234 Fax 0870 24 03 61348 Anchor Bay 2005
Expamet brick tie products
Expamet multi starter
Exmet brick reinforcement
Expamet brickstrength
Featuring a ‘turn-n-slide’ tie which
enables the starter to be tied into any
course the builder wishes, ideally every
(225mm deep) block course or every
third (75mm deep) bricks. Supplied in
pack form only. Pack contents: Two
1165mm stainless steel lengths, ten ties,
five screws, wall plugs and washers
An expanded stainless steel metal
manufactured to BS EN 10088-1: 1995:
1.4301 (Grade 304/S15). Where greater
strength is required to allow for uneven
settlement and movement in buildings it
is desirable to use exmet reinforcement in
the joints.
Reinforcement for mortar bed joints in
brickwork. Manufactured from stainless
steel type BS EN 10088-1,1.430.
Code Description
M/STARTER Mutli starter kit
Code Description
BMESH65 65mm exmet
BMESH115 115mm exmet
BMESH175 175mm exmet
B/MESH225 225mm exmet
Code Description
BRICK60 60mm brickstrength
BRICK100 100mm brickstrength
BRICK150 150mm brickstrength
BRICK175 175mm brickstrength
BRICK200 200mm brickstrength
Width (mm) Length (mm) Wire diameter (mm)
60 3050 4
100 3050 4
150 3050 4
175 3050 4
200 3050 4
Material Coil size Coil size Suitable for minimum thickness (mm) width (mm) length (mm) wall thickness (mm)
0.3 65 20 75
0.3 115 20 140
0.3 175 20 190
0.3 225 20 250
Telephone 0870 24 24 234 Fax 0870 24 03 613 Anchor Bay 2005 49
Frame crampA safe edge frame cramp which provides
positive location of window and door
frames to masonry manufactured from
pre-galvanised steel strip with zinc
coated edges to BS EN 10142: 1991.
Code Description
F/CRAMP100 100mm x 50mm
F/CRAMP150 150mm x 50mm
F/CRAMP200 200mm x 50mm
Expamet brick tie products cont.
Width (mm) Length (mm) Upstand (mm) Quantity/Box (mm)
28 100 50 250
28 150 50 250
28 200 50 250
Telephone 0870 24 24 234 Fax 0870 24 03 61350 Anchor Bay 2005
Tools
Wire brush
Mixing paddle
Skeleton gun
Turks head brush
Scoop
Sprayers
Barrel accessories
A construction duty wire brush.
Used for the mixing of non shrink grouts
and other powders. Manufactured to suit
all heavy duty electrical drills.
An application gun used to dispense
products from 310ml cartridges.
Used for the application of bitumen
emulsion, primers and other liquids to
concrete surfaces.
An aluminium scoop for use with cube
moulds and other test equipment.
High performance sprayer units for the
application of mould oil and chemical
release agent.
Taps and pumps used in conjunction with
plastic and metal barrels.
Code Description
W/BRUSH Wire brush
Code Description
PADDLE Mixing paddle
Code Description
SKELG Skeleton gun
Code description
BRUSH Turks head
Code Description
SCOOP Scoop
Code Description
MS08/S 8ltr metal sprayer
PS08 8ltr plastic sprayer
KN20 20ltr knapsack
NOZZ Nozzle
LANCE Sprayer lance
TRIGGER Sprayer trigger unit
GASK/M Metal gasket set
GASK/P Plastic gasket set
SOLV/5 Cleaning solvent 5ltr
SOLV/25 Cleaning solvent 25ltr
Code Description
TAP 3/4’’ barrel tap
PUMP Barrel pump
Telephone 0870 24 24 234 Fax 0870 24 03 613 Anchor Bay 2005 51
Tools cont.
Carborundum stone
Hand floats
Buckets
Tying wire nips
Scraper
Utility knife
Cranking Irons
A carborundum rubbing block used to
smoothen out uneven concrete
repaired surfaces.
A range of floats used for the placing
and floating of concrete.
A heavy duty PVC site bucket.
The most popular tool used by all steel
fixers for the tying of reinforcement.
Used for cleaning residue concrete from
formwork panels.
A heavy duty utility knife pack which
includes holder and spare blades.
A tool used for the straightening of rebar.
Available in three sizes to cover a range
of rebar diameters.
Code Description
C/STONE Carborundum stone
Code Description
P/FLOAT Plastic float
M/FLOAT Metal float
W/FLOAT Wooden float
Code Description
BUCKET Site bucket
Code Pack
NIPS Each
Code Pack
SCRAPER/LONG Each
Code Description
S/KNIFE Utility knife set
Code Description
CRANK 14-16mm rebar
CRANK/20 18-20mm rebar
CRANK/26 25mm rebar
Telephone 0870 24 24 234 Fax 0870 24 03 61352 Anchor Bay 2005
Setting out products
Line marking spray
Plastic barrier fencing
Fencing pins
Hazzard tape
An aerosol spray used for marking or
lining areas on site. Available in colours
yellow, red, blue and white and packed 6
750ml cans per box.
A heavy duty highly visible orange
polythene barrier fencing supplied in rolls.
Roll size 1m x 50m
A mild steel pin , pointed one end and a
curled lamp hook on the other. Size: 1.35
metre long.
A white and red diagonally warning tape
supplied in 500 metre rolls.
Code Colour
LINE/Y Yellow
LINE/R Red
LINE/B Blue
LINE/W White
Code Size
BARRIER 1m x 50m
Code Size
F/PIN 1.350M
Code Size
BARRIER/TAPE 500m
Telephone 0870 24 24 234 Fax 0870 24 03 613 Anchor Bay 2005 53
Reinforcing bar to bs 4449 and cut and bent to BS8666:2000, supplied in high yield grade
460n/mm2 and plaind round to grade 250n/mm2.
Size 8mm 10mm 12mm 16mm 20mm 25mm 32mm 40mm
Kg/m 0.222 0.395 0.888 1.579 2.466 3.854 6.313 9.864
12m/tonne 211 135 94 53 34 22 13 8
Cut and bent reinforcements
Shape codes to BS 8666:2000
00
11
12
13
15
21
25
26
31
33
41
44
46
51
67
77
All other shapes are shape code 99 and require a fully dimensional sketch
Telephone 0870 24 24 234 Fax 0870 24 03 61354 Anchor Bay 2005
1. GENERALThe following Terms & Conditions apply to all agreements entered by the company for the Manufacturer and supply of its goods and services. No variation of our addition to the terms shall be valid unless authorised in writing by a Director of the company.
2. QUOTATIONSA quotation does not constitute an offer. No contract is concluded until written confirmation by the company is sent on receipt of order.
3. PERFORMANCES AND SPECIFICATION Any performance estimate is given without commitment and is based upon the company’s experience only. Whilst every effort is made to ensure the accuracy of the details in our catalogue this is subject to a general acceptance of minor errors and omissions.
4. PRICEPrices quoted are based upon current conditions, costs of labour materials and statuary charges and are subject to increase without notice to take account of variations or alterations of the same. The company accordingly reserves the right to adjust invoice prices in the event of any increase in the cost of materials, transport or of labour and/or take account of any other costs that may arise in result of legalisation or by reason of any other event unknown to the company at the date of quotation.
5. PAYMENT The payment terms in the company’s quotation must be strictly adhered to. In the event that payment is not made by the due date, the company shall be entitled to charge the customer interest on any overdue amount at the rate of 2% per month (or at such other rate as may be advised by the company from time to time). For each month or part month, which the said amounts, are to remain overdue. The customer shall not be entitled to retain, deduct or defer any sums whatsoever due to the company under the contract on account of any dispute, cross claim or set-off which it might have with the company. Non-compliance with payment terms will entitle the company to withhold further deliveries and/or labour forthwith. The company’s delivery notice/invoice copy receipted on behalf of the customer or such other reasonable evidence as may be declared shall be sufficient proof of delivery for this purpose.
6. OWNERSHIP AND RISK (i) The risk of damage to any goods shall pass to the customer on delivery.(ii) Title to any goods shall not pass to the customer until the company has received
payment in full of all accounts under each and every contract between the company and the customer existing at delivery. In the meantime, the goods shall remain property of the company and the customer shall hold them in a fiduciary capacity as the company’s bailee free from any charge, lien or other encumbrance. During this period:
(a) the customer shall keep the goods or any other property into which they are incorporated fully insured with a reputable insurer and if possible, store them separately and/or keep them in such a way that they can be clearly identified as the company’s property; and
(b) the company shall be entitled to recover possession of the goods (or any of them) at anytime to lawfully enter upon any of the customer’s (and for any reason) (and even by
severance from other property) shall be entitled without restriction to lawfully enter upon any of the customer’s premises for that purpose. The customer shall pay all costs and expenses incurred by the company in exercising this right.
(iii) Not withstanding that title may not have passed to the customer, the company may maintain an action for the price of the goods and the customer acknowledges that nothing in sub clause (ii) above confers any right to upon it to return or reject the goods or refuse, defer or delay payment from them.
7. DELIVERY AND [LIEN] (i) Although the company will use reasonable commercial endeavours to deliver goods
within any time estimates given, time of delivery is not the essence of the contract and delay shall not therefore entitle the customer to repudiate. Neither shall the company be liable to the customer for any loss or damages whatsoever suffered or sustained as a result of the company failing to adhere to such times or dates.
(ii) The company shall be entitled to deliver by single delivery or instalments. Without prejudice to sub clause (i) above, non-delivery of any instalment or delay in delivery shall not affect the balance of the contract or entitle the customer to terminate the same. However, the company shall be entitled to levy additional charges where the customer fails or refuses for any reason to take delivery and shall be entitled to determine the contract forthwith if the customer the fails to take delivery within fourteen days of a written request requiring them to do so.
(iii) The company shall upon notice to the customer be entitled to withhold delivery or suspend performance of the contract generally if at the time of the notice any credit limit extended to the customer has been exceeded or payment of any of the company’s invoices (whether related to the contract or not) is then overdue. If the customer fails within fourteen days of the notice to reduce its indebtedness to the level requested or to settle the said invoices, then the company shall, without further notice to the customer, be entitled to determine the contract forthwith.
(iv) In addition to the above, the company shall (without prejudice to any other remedy available to it) have in respect of all unpaid debts and other sums due from the customer under the contract a general lien on any goods whatsoever in its possession (whether in relation to the contract or otherwise) which are or are intended to become the property of the customer and pursuant to that lien or right the company shall be entitled upon fourteen days written notice to the customer to sell any goods so held upon such terms as it thinks fit and to keep the proceeds of sale thereof in diminution of the sum due to it and all costs and expenses incurred in or about effecting the sales.]
8. FAULTY GOODS AND LIMITATION ON LIABILITY(i) Whilst all reasonable care is taken in compiling technical data on the company’s products
all recommendations or suggestions regarding the use of such products are made without guarantee since the conditions of use are beyond the control of the company. It is the customer’s responsibility to satisfy them that each product is fit for the purpose for which they intended to use it and the actual conditions of sale are suitable.
(ii) Not withstanding that it will not be responsible for any defects caused or sustained as a result of variations in the customer’s original specifications, the company warrants that its goods will be of satisfactory quality and that all service it provides by it will be performed with reasonable skill and care. Accordingly, the company will replace any goods that are defective, damaged or faulty at its own expense (provided that they have not been tampered with or subjected to improper treatments by the customer) if the customer gives written notice of the faults and defects within seven days of delivery. Goods to be replaced must be returned to the company properly packed and carriage paid before any replacement will be issued and notwithstanding clause 6(ii) hereof, goods so returned become the property of the company.
(iii) Save as hereinbefore provided the company shall not be liable to compensate for indemnify the customer for any loss or damage (whether direct, indirect, consequential or otherwise) to or caused by or sustained as a result of the goods or services provided
(iv) Not withstanding anything hereinbefore contained, the company is not seeking to exclude or restrict its potential liability for damage in the nature of death or the negligence or that of its servants or agents causes personal injury. However, the customer shall indemnify the company against all actions, claims, proceedings losses, costs, damages and expenses whatsoever arising in respect of loss of life or personal injury suffered by any person in connection with the contract where that loss of life or personal injury is caused by negligence of the customer or of its servants or agents.
(v) A film of rust or mill scale on reinforcement will not constitute grounds for rejection.
9. CANCELLATIONThe customer may not cancel all or any part of the contract without the written consent of the company.
10. INTELLECTUAL PROPERTY The patent, registered design, copyright and any other intellectual property rights attached to all goods and component parts, drawings, designs and plans of such goods are actually invented or designed by the company shall remain vested and the customer shall not therefore be entitled to copy to reproduce or procure the copying or reproduction of the same without the company’s written consent.
11. FORCE MAJEURE In the event the normal course of the contract is frustrated, prevented, Interrupted, hindered delayed or rendered unduly expensive by any cause whatsoever beyond its control, the company shall promptly give notice thereof to the customer and shall have the right to cancel the contract or to defer its performance for as long as such force majeure shall continue.
12. PROPER LAW The construction, validity and performance of the contract shall be governed by English Law and all disputes shall govern the construction, validity and performance of the contract or the English Courts shall decide questions that may arise out of or in connection with or in relation to the contract.
1. Carriage paid on all orders except: (i) Orders less then £300 in invoice value and are subjected to a £20.00 delivery charge. (ii) Orders dispatched at the customer’s request by express delivery/courier,
carriage at a cost.2. Deliveries are provided to customer’s requirements by or own transport.3. Deliveries are usually delivered within 48 hours of receipt of order for ex-stock items.4. All prices in the catalogue are exclusive of VAT5. The catalogue price list replaces all other price lists.6. All sales are subject to our standard terms and conditions of sale.7. Whilst all reasonable care is taken in complying technical data on the company’s
products are made without guarantee since the conditions of use are beyond the control of the company. It is the customer’s responsibility to satisfy himself that each product is fit fir the purpose for which he/she intends to use it and that actual conditions of use are suitable.
DELIVERY TO NEAREST HARD ROAD TO SITE Errors and omissions accepted. This applies to all aspects of our catalogue.
ANCHOR BAY CONSTRUCTION PRODUCTS LTD & ANCHOR BAY BEAM FORMUNIT C79 BANNING STREET GREENWICH LONDON SE10 ONT
Terms and Conditions
Quality products on time every time
Anchor Bay Construction Products Limited Unit C, 79 Banning Street, London SE10 ONT
T: 0870 24 24 234 F: 0870 24 03 613 [email protected] www.anchor-bay.co.uk