transmission bearings & housing catalogue
Post on 28-Mar-2016
297 Views
Preview:
DESCRIPTION
TRANSCRIPT
www.bsc.com.au
TM
Certi
fied S
yste
m
QualityISO 9001 SAI GLOBALMoorebankNorthgateClayton
2
6-12 Standard
80 100 176 212 1 Month Standard
100 130 212 266 1 Month Heat Resistant
Recommended Replenishing Interval and Operating Temperature
RecommendedReplenishing
Interval
Up to 80 Up to 176
2-3 Shots Maximum
Bearing Type
Operating Temperature
°C °F
Shaft Bearing Diameter Series
inch mm12.000 201 P203
1/2 12.7009/16 14.288
15.000 202 P2035/8 15.875
17.000 203 P20311/16 17.4623/4 19.050 204 P204 UP204 T204 F204 FC204 FL204 FA204 HB204 C204 FH204
20.00013/16 20.6387/8 22.22515/16 23.812 205 P205 SB205 UP205 T205 F205 FC205 FL205 FA205 HB205 C205 FH205
25.0001 25.4001-1/16 26.9881-1/8 28.575
30.000 206 P206 SB206 UP206 T206 F206 FC206 FL206 FA206 HB206 C206 FH2061-3/16 30.1621-1/4 31.7501-1/4 31.7501-5/16 33.3381-3/8 34.925 207 P207 SB207 UP207 T207 F207 FC207 FL207 FA207 HB207 C207 FH207
35.0001-7/16 36.5121-7/16 36.5121-1/2 38.100 208 P208 SB208 UP208 T208 F208 FC208 FL208 FA208 HB208 C208 FH2081-9/16 39.688
40.0001-5/8 41.2751-11/16 42.862 209 P209 SB209 UP209 T209 F209 FC209 FL209 FA209 HB209 C209 FH2091-3/4 44.450
45.0001-13/16 46.0381-7/8 47.6251-15/16 49.212 210 P210 SB210 UP210 T210 F210 FC210 FL210 FA210 HB210 C210
50.0002 50.8002 50.8002-1/16 52.3882-1/8 53.975 211 P211 SB211 T211 F211 FC211 FL211 FA211 HB211 C211
55.0002-3/16 55.5622-1/4 57.1502-5/16 58.738 212 P212 SB212 T212 F212 FC212 FL212 HB212 C212
60.0002-3/8 60.3252-7/16 61.9122-1/2 63.500 213 P213 SB213 T213 F213 FC213 FL213 HB213 C213
65.0002-5/8 66.6752-11/16 68.262 214 P214 SB214 T214 F214 FC214 FL2142-3/4 69.850
70.0002-13/16 71.4382-7/8 73.0252-15/16 74.612 215 P215 SB215 T215 F215 FC215 FL215
75.0003 76.2003-1/8 79.375
80.000 216 P216 SB216 T216 F216 FC216 FL2163-3/16 80.9623-1/4 82.550 217 P217 SB217 T217 F217 FC217 FL217
85.0003-7/16 87.3123-1/2 88.900 218 P218 SB218 F218 FC218 FL218
T TT TTemperature Ranges for Mounted Ball Bearing Unitsemperature Ranges for Mounted Ball Bearing Unitsemperature Ranges for Mounted Ball Bearing Unitsemperature Ranges for Mounted Ball Bearing Unitsemperature Ranges for Mounted Ball Bearing Units
Thickener Basic Oil Type Material
Standard D1 -10 to +110 NormalLithiumSoap
MineralOil
ContactNitrite
Rubber
Coldproof CLithiumSoap
SiliconeOil
Semi- Resistant
H -10 to +120 C3Lithium
ComplexSoap
SiliconeOil
ContactHeat
ResistantRubber
Temperature Ranges for Mounted Ball Bearing Units
Enclosed Grease SealType Symbol
TemperatureRange
°C
RadialClearanceof Bearing
Additional Housing Seal
Pressed Steel Cast Cover
-50 to +110 Normal
BALL BEARING UNITS BALL BEARING UNITS
WIR HOUSING RANGE
BSC 200 SERIES WIDE RE-GREASEABLE UNITS
3
UC 200UC 200UC 200UC 200UC 200 UC X00UC X00UC X00UC X00UC X00 UC 300UC 300UC 300UC 300UC 300 AS 200AS 200AS 200AS 200AS 200
UC 2 Set Screw Cylindrical 2 Grease fitting Wide Spherical
UC 3 Set Screw Cylindrical 3 Grease fitting Wide Spherical
UC X Set Screw Cylindrical X Grease fitting Wide Spherical
UEL 2 Eccentric Locking Collar Cylindrical 2 Grease fitting Wide Spherical
UK 2 Adapter Sleeve Tapered 2 Grease fitting Wide Spherical
UK 3 Adapter Sleeve Tapered 3 Grease fitting Wide Spherical
UK X Adapter Sleeve Tapered X Grease fitting Wide Spherical
AS 2 Set Screw Cylindrical 2 None Narrow Spherical
AEL 2 Eccentric Locking Collar Cylindrical 2 Grease fitting Narrow Spherical
AELS 2 Eccentric Locking Collar Cylindrical 2 None Narrow Cylindrical Flat OD
UCS 2 Set Screw Cylindrical 2 Grease fitting Wide Cylindrical Flat OD
Type Locking Method Bore Diameter Relubricating Width Outside DiameterSeries Capability
AEL 200AEL 200AEL 200AEL 200AEL 200UEL 200UEL 200UEL 200UEL 200UEL 200
UK 300UK 300UK 300UK 300UK X00UK X00UK X00UK X00UK 200UK 200UK 200UK 200UK 200
UCS 200UCS 200UCS 200UCS 200UCS 200AELS 200AELS 200AELS 200AELS 200AELS 200
UK 300UK X00
BALL BEARING UNITS BALL BEARING UNITS
SELECTION GUIDE
BSC HOUSING BEARING INSERTS RANGE
4
Shaft Dia Dimensions Bolt Used Unit No. in mm h a e b S2 S1 g w bi n in mm
Bearing No.
HousingNo.
Weightkg
Coverst( in )
( mm )
UCP201201-008202202-010203
1/2
5/8
12
15
17
13/16 30.2
5127
3 3/4 95
1 1/2 38
3/419
1/2 13
15/32 12
2 3/8 60
1.220531.0
0.500012.7 3/8 10
UC201 201-008202202-010203
P204 0.70 1 23/3244
UCP204 204-012 3/4 20 1 5/16
33.35 3 3/4 1 1/2
383/413
1/2 13
2 17/3264.3
1.220531.0
0.500012.7 3/8 10 UC204
204-012 P204 0.70 1 23/3244
UCP205 205-014 205-015 205-100
7/815/16 1
251 7/16 36.5
5 1/2 140
4 1/8 105
1 1/2 38
3/419
19/32 15
19/32 15
2 25/3271
1.342034.1
0.563014.3 3/8 10
UC205 205-014 205-015 205-100
P205 0.86 1 27/3247
UCP206 206-102 206-103 206-104
1 1/8 1 3/16 1 1/4
30 111/16 42.9
6 1/2 165
4 3/4 121
1 7/8 48 13/16 21/32
1721/32
173 5/16
841.5000
38.1 0.6260
15.9 1/2 14
UC206 206-102 206-103 206-104
P206 1.41 2 1/16 52
UCP207 207-104 207-105 207-106 207-107
1 1/4 1 5/16 1 3/8 1 7/16
35
1 7/8 47.6
6 9/16167
5127
1 7/8 48
13/16 21
21/32 17
25/3218
3 21/3293
1.689042.9
0.689017.5 1/2 14
UC207 207-104 207-105 207-106 207-107
P207 1.66 2 5/1659
UCP208 208-108 208-109
1 1/2 1 9/16
40 115/16 49.2
7 1/4 184
5 13/32 137
2 1/8 54
13/16 21
21/32 17
25/32 18
3 27/3298
1.937049.2
0.748019.0 1/2 14
UC208 208-108 208-109
P208 2.12 2 11/1668
UCP209 209-110 209-111 209-112
1 5/8 1 11/16 1 3/4
452 1/8 54.0
7 15/32190
5 3/4 146
2 1/8 54
13/16 21
21/32 17
25/32 20
4 3/16106
1.937049.2
0.748019.0 1/2 14
UC209 209-110 209-111 209-112
P209 2.40 2 11/1668
UCP210210-114210-115
1 7/8 1 15/16
50 2 1/4 57.2
8 1/8 206
6 1/4 159
2 3/8 60
7/822
25/3220
25/3221
4 7/16113
2.031551.6
0.748019.0 5/8 16
UC210 210-114210-115
P210 2.94 2 7/8 73
UCP211 211-200 211-202 211-203
22 1/8 2 3/16
552 1/2 63.5
8 5/8 219
6 23/32 171
2 3/8 60
7/822
25/3220
29/3223
4 29/32125
2.189055.6
0.874022.2 5/8 16
UC211 211-200 211-202 211-203
P211 3.66 2 15/1675
UCP212212-204212-206212-207
2 1/4 2 3/8 2 7/16
602 3/4 69.8
9 1/2 241
7 1/4 184
2 3/4 70
125
25/3220
125
5 7/16138
2.563065.1
1.000025.4 5/8 16
UC212212-204212-206212-207
P212 5.15 3 15/3288
UCP213 213-208 2 1/2
65 376.2
10 7/16265
8203
2 3/4 70
1 3/1630
125
1 1/827
5 29/32150
2.563065.1
1.000025.4 3/4 20 UC213
213-208 P213 6.10 3 15/3288
UCP214 214-212 2 3/4 70 3 1/8
79.410 15/32
2668 9/32
2102 27/32
721 3/16
301
251 1/827
6 5/32156
2.937074.6
1.189030.2 3/4 20 UC214
214-212 P214 6.90 3 27/3298
UCP215215-215 215-300
2 15/16 3
75 3 1/4 82.6
10 13/16275
8 17/32 217
2 29/32 74
1 3/1630
125
1 3/3228
6 3/8 162
3.063077.8
1.311033.3 3/4 20
UC215 215-215 215-300
P215 7.85 3 27/3298
UCP216 80 88.9 292 232 78 30 25 30 175 82.6 33.3 3/4 20 UC216 P216 9.0UCP217 85 95.2 310 247 83 30 25 32 187 85.7 34.1 3/4 20 UC217 P217 11.38UCP218 90 101.6 327 262 88 30 27 33 200 96.0 39.7 1 24 UC218 P218 13.46
( in ) ( mm )
127 951/2 14
BALL BEARING UNITS BALL BEARING UNITS
NORMAL DUTY PILLOW BLOCKS
UCP200 SERIES
Triple Lip Seal
Additional sizes are available. Contact your nearest BSC store.
5
BALL BEARING UNITS BALL BEARING UNITS
Shaft Dia Dimensions Bolt Used Unit No. in mm a e i g l s z Bi n in mm
Bearing No. No. kg
Coverst( in )
( mm )UCF201 201-008 202 202-010 203 204 204-012
1/2
5/8
3/4
12
15
1720
3 3/8 86
2 33/64 64
19/32 15
15/32 12
125.5
15/32 12
1 5/16 33.3
1.220531.0
0.500012.7 3/8 10
UC201 201-008 202 202-010 203 204 204-012
F204 0.65 1 15/3237.0
UCF205 205-014 205-015 205-100
7/815/16 1
253 3/4
952 3/4
705/816
9/16 14
1 1/16 27
15/32 12
1 13/3235.7
1.3386 34.1
0.563014.3 3/8 10
UC205
F205 0.85 1 9/16 39.5
UCF206 206-102 206-103 206-104
1 1/8 1 3/16 1 1/4
304 1/4 108
3 17/64 83
45/64 18
9/16 14
17/32 31
15/32 12
1 19/3240.2
1.500038.1
0.626015.9 3/8 10
UC206
F206 1.60 1 29/3248.5
UCF207 207-104 207-105 207-106 207-107
1 1/4 1 5/16 1 3/8 1 7/16
35
4 19/32 117
3 5/8 92
3/419
5/816
1 11/32 34
35/64 14
1 3/4 44.4
1.689042.9
0.689017.5 7/16 12
UC207
F207 1.60 1 29/3248.5
UCF208 208-108 208-109
1 1/2 1 9/16
40 5 1/8 130
4 1/64 102
53/64 21
5/816
1 13/3236
5/816
2 1/64 51.2
1.9370 49.2
0.7480 19.0 1/2 14
UC208F208 2.05 2 5/32
55.0
UCF209 209-110 209-111 209-112
1 5/8 1 11/16 1 3/4
455 13/32
137 4 9/64
10555/64
2223/32
181 1/2
385/816
2 1/16 52.2
1.9370 49.2
0.7480 19.0 1/2 14
UC209
F209 2.38 2 7/3256.0
UCF210 210-114 210-115
1 7/8 1 15/16
50 5 5/8 143
4 3/8 111
55/6422
23/32 18
1 9/16 40
5/816
2 5/32 54.6
2.031551.6
0.7480 19.0 1/2 14
UC210 F210 2.50 2 5/16
58.5
UCF211 211-200 211-202 211-203
22 1/8 2 3/16
556 3/8
162 5 1/8 130
63/64 25
25/32 20
1 11/16 43
3/419
2 19/64 58.4
2.189055.6
0.8740 22.2 5/8 16
UC211
F211 3.60 2 15/3262.5
UCF212 212-204 212-206 212-207
2 1/4 2 3/8 2 7/16
606 7/8
1755 5/8
143 1 9/16
2925/32
201 7/8
483/419
2 45/6468.7
2.563065.1
1.000025.4 5/8 16
UC212
F212 4.90 2 7/8 73.0
UCF213 213-208 2 1/2
65 7 3/8 187
5 55/64 149
1 3/16 30
25/32 20
1 31/3250
3/419
2 3/4 69.7
2.563065.1
1.000025.4 5/8 16 UC213 F213 5.90 2 29/32
73.5 UCF214 214-212 2 3/4
70 7 19/32 193
5 63/64 152
1 7/32 31
15/16 24
2 1/8 54
3/419
2 31/3275.4
2.9370 74.6
1.189030.2 5/8 16 UC214 F214 6.30 3 5/32
80.0UCF215 215-215 215-300
2 15/16 3
75 7 7/8 200
6 17/64 159
1 11/32 34
15/16 24
2 7/32 56
3/419
3 3/32 78.5
3.063077.8
1.3110 33.3 5/8 16
UC215 F215 6.80 3 9/32
83.0
UCF216 80 208 165 34 24 58 23 83.3 82.6 33.3 20 UC216 F216 8.2UCF217 85 220 175 36 26 63 23 87.6 85.7 34.1 20 UC217 F217 9.3UCF218 90 235 187 40 26 68 23 96.3 96.0 39.7 20 UC218 F218 11.3
( in ) ( mm ) Housing Weight
205-014 205-015 205-100
206-102 206-103 206-104
207-104 207-105 207-106 207-107
208-108 208-109
209-110 209-111 209-112
210-114 210-115
211-200 211-202 211-203
212-204 212-206 212-207
213-208
214-212
215-215 215-300
NORMAL DUTY FLANGE UNITS
UCF200 SERIES
Triple Lip Seal
Additional sizes are available. Contact your nearest BSC store.
6
Shaft Dia Dimensions Bolt Used Unit No. in mm a e i g l s b z Bi n in mm
Bearing No.
HousingNo.
Weightkg
Coverst( in )
( mm )UCFL201 201-008 202 202-010 203 204 204-012
1/2
5/8
3/4
12
15
1720
4 7/16 113
3 35/6490
19/32 15
7/1611
125.5
15/32 12
2 3/8 60
1 5/1633.3
1.220531.0
0.500012.7 3/8 10
UC201 201-008 202 202-010 203 204 204-012
FL204 0.60 1 15/3237.0
UCFL205 7/815/16 1
255 1/8 130
3 57/6499
5/816
1/2 13
1 1/16 27
5/816
2 11/1668
1 13/3235.7
1.342034.1
0.563014.3 1/2 14
UC205
FL205 0.70 1 9/16 39.5
UCFL206 1 1/8 1 3/16 1 1/4
30 513/16
148
4 39/64117
45/64 18
1/2 13
1 7/3231
5/816
3 5/3280
1 37/6440.2
1.500038.1
0.626015.9 1/2 14
UC206
FL206 0.98 1 23/3244.0
UCFL207 1 1/4 1 5/16 1 3/8 1 7/16
356
11/32 161
5 1/8 130
3/419
19/32 15
1 11/3234
5/816
3 17/3290
1 3/4 44.4
1.689042.9
0.689017.5 1/2 14
UC207
FL207 1.35 1 29/3248.5
UCFL208 1 1/2 1 9/16
40 6 7/8 175
5 43/64144
53/64 21
19/32 15
1 13/3236
5/816
3 15/16100
2 1/6451.2
1.937049.2
0.748019.0 1/2 14
UC208FL208 1.69 2 5/32
55.0
UCFL209 1 5/8 1 11/16 1 3/4
45 713/32
188
5 53/64148
55/6422
5/816
1 1/2 38
3/419
4 1/4 108
2 1/16 52.2
1.937049.2
0.748019.0 5/8 16
UC209 FL209 2.04 2 7/32
56.0
UCFL210 1 7/8 1 15/16
50 7 3/4 197
6 3/16157
55/6422
5/8 16
1 9/1640
3/419
4 17/32115
2 5/3254.6
2.031551.6
0.748019.0 5/8 16
UC210 FL210 2.30 2 5/16
58.5
UCFL211 22 1/8 2 3/16
55 813/16
224
7 1/4 184
63/64 25
23/32 18
1 11/1643
3/419
5 1/8 130
2 19/6458.4
2.189055.6
0.874022.2 5/8 16
UC211
FL211 3.30 2 15/3262.5
UCFL2122 1/4 2 3/8 2 7/16
609
27/32 250
7 61/64202
1 9/64 29
23/32 18
1 7/8 48
29/3223
5 1/2 140
2 45/6468.7
2.563065.1
1.000025.4 3/4 20
UC212 FL212 4.30 2 7/8
73.0
UCFL213 2 1/2
65 10 5/32 258
8 17/64210
1 3/16 30
25/32 20
1 31/3250
29/3223
6 3/32155
2 3/4 69.7
2.563065.1
1.000025.4 3/4 20 UC213 FL213 5.40 2 29/32
73.5 UCFL214
2 3/4 70
265 216 31 22 54 23 160 75.4 74.6 30.2 3/4 20UC214 FL214 5.6
UCFL215 2 15/16 3
75
275 225 34 22 56 23 165 78.5 77.8 33.3 3/4 20
UC215 FL215 6.2
UCFL216 80 290 233 34 22 58 25 180 83.3 82.6 33.3 3/4 20 UC216 FL216 7.8
( in ) ( mm )
205-014 205-015 205-100
206-102 206-103 206-104
207-104 207-105 207-106 207-107
208-108 208-109
209-110 209-111 209-112
210-114 210-115
211-200 211-202 211-203
212-204 212-206 212-207
213-208
214-212
215-215 215-300
205-014 205-015 205-100
206-102 206-103 206-104
207-104 207-105 207-106 207-107
208-108 208-109
209-110 209-111 209-112
210-114 210-115
211-200 211-202 211-203
212-204 212-206 212-207
213-208
214-212
215-215 215-300
BALL BEARING UNITS BALL BEARING UNITS
NORMAL DUTY FLANGE UNITS
UCFL200 SERIES
Triple Lip Seal
Additional sizes are available. Contact your nearest BSC store.
7
BALL BEARING UNITS BALL BEARING UNITS
Shaft Dia DimensionsUnit No. in mm o g q p s b k e a w j l h Bi n
BearingNo. No. kg
UCT 201 UCST201-008 UCT 202 UCST202-010UCT 203
204 UCST204-012
1/2
5/8
3/4
12
15
1720
5/816
3/810
251
1 1/4 32
3/419
251
0.47212
376
3 1/2 89
3 11/1694
1 1/4 32
15/1624
2 3/8 60
1.220531.0
0.500012.7
UC201 201-008 202 202-010 203 204
204-012
ST204T204NBR 0.80
UCT 205UCST205-014
205-015205-100
7/815/16 1
255/816
3/810
251
1 1/4 32
7/822
251
0.47212
376
3 1/2 89
3 13/1697
1 1/432
15/1624
2 7/16 62
1.3386 34.1
0.563014.3
UC205 205-014 205-015 205-100
ST205 T205NBR 0.86
UCT 206 UCST206-102
206-103206-104
1 1/8 1 3/16 1 1/4
305/816
3/810
2 3/1656
1 7/16 37
7/822
2 1/4 57
0.47212
3 1/2 89
4 102
4 7/16113
1 7/1637
15/1624
2 3/4 70
1.500038.1
0.626015.9
UC206 206-102 206-103 206-104
ST206 T206NBR 1.28
UCT 207UCST207-104
207-105207-106207-107
1 1/4 1 5/16 1 3/8 1 7/16
35
5/816
1/2 13
2 1/2 64
1 7/16 37
7/822
2 1/2 64
0.47212
3 1/2 89
4 102
5 1/16129
1 7/1637
1 3/1630
3 1/16 78
1.689042.9
0.689017.5
UC207 207-104 207-105 207-106 207-107
ST207 T207NBR 1.68
UCT 208 UCST208-108 208-109
1 1/2 1 9/16
40 3/419
5/816
3 1/4 83
1 15/16 49
1 1/8 29
3 1/4 83
0.63016
4102
4 1/2 114
5 11/16144
1 15/1649
1 3/8 35
3 1/2 89
1.9370 49.2
0.748019.0
UC208 208-108 208-109
ST208 T208NBR 2.42
UCT 209 UCST209-110
209-111209-112
1 5/8 1 1/16 1 3/4
453/419
5/816
3 1/4 83
1 15/16 49
1 1/8 29
3 1/4 83
0.63016
4102
4 5/8117
5 11/16144
1 15/1649
1 3/8 35
3 7/16 87
1.9370 49.2
0.748019.0
UC209 209-110 209-111 209-112
ST209 T209NBR 2.52
UCT 210 UCST210-114 210-115
1 7/8 1 15/16
50 3/419
5/816
3 1/4 83
1 15/16 49
1 1/8 29
3 3/886
0.63016
4102
4 5/8117
5 7/8 149
1 15/1649
1 3/8 35
3 9/16 90
2.031551.6
0.748019.0
UC210 210-114 210-115
ST210 T210NBR 2.75
UCT 211 UCST211-200
211-202 211-203
22 1/8 2 3/16
551
253/419
4 102
2 1/2 64
1 3/8 35
3 3/495
0.86022
5 1/8130
5 3/4146
6 3/4 171
2 1/264
1 5/8 38
4 3/16 106
2.189055.6
0.874022.2
UC211 211-200 211-202 211-203
ST211 T211NBR 4.10
UCT 212 UCST212-204
212-206212-207
2 1/4 2 3/8 2 7/16
601 1/4
323/419
4 102
2 1/2 64
1 3/8 35
4102
0.86022
5 1/8130
5 3/4146
7 5/8 194
2 1/264
1 13/1642
4 11/16 119
2.563065.1
1.000025.4
UC212 212-204 212-206 212-207
ST212 T212NBR 4.90
UCT 213 UCST213-208 2 1/2
65 1 1/4 32
13/16 21
4 3/8111
2 3/4 70
1 5/8 41
4 3/4121
1.024926
5 15/16151
6 9/16167
8 13/16224
2 3/470
244
5 3/8 137
2.563065.1
1.000025.4
UC213 213-208
ST213 T213NBR 7.05
UCT 214 70 32 21 111 70 41 121 26 151 167 224 70 46 137 74.6 30.2 UC214 T214NBR 7.10UCT 215 75 32 21 111 70 41 121 26 151 167 232 70 48 140 77.8 33.3 UC215 T215NBR 7.50UCT 216 80 32 21 111 70 41 121 26 165 184 235 70 51 140 82.6 33.3 UC216 T216NBR 8.50
( in ) ( mm ) Housing Wt.
NORMAL DUTY TAKE-UP UNITS
UCT200/UCST200 SERIES
Triple Lip Seal
Additional sizes are available. Contact your nearest BSC store.
8
INSERT BEARINGS BEARINGS & HOUSINGS
NORMAL DUTY PILLOW BLOCKS
UC200 SERIES, Set ScrewNORMAL DUTY PILLOW BLOCKS
UEL200 SERIES, Eccentric Lock
in mm Dynamic Static in mm Dynamic Static UC201-008NBRTL 1/2 1010 630 UEL204-012NBRTL 3/4 1010 630UC202-010NBRTL 5/8 1010 630 UEL205-100NBRTL 1UC204-012NBRTL 3./4 1010 630 UEL205NBRTL 25 1100 710UC204NBRTL 20 UEL206-102NBR 1 1/8UC205-014NBRTL 7/8 1100 710 UEL206-104NBRTL 1 1/4 1540 1020
UC205-100NBRTL 1
UEL206NBRTL 30
UC206-102NBRTL 1 1/8
UEL207-104NBRTL 1 1/4
UC206-103NBRTL 1 3/16
UEL207-106NBRTL 1 3/8
UC206-104NBRTL 1 1/4 1540 1020
UEL207NBRTL 35 2030 1400
UC206NBRTL 30
UEL208-108NBRTL 1 1/2
UC207-104NBRTL 1 1/4
UEL208-112NBR 1 3/4 2300 1600
UC207-106NBRTL 1 3/8 2030 1400
UEL208NBRTL 40
UC207NBRTL 35
UEL209NBRTL 45 2570 1810
UC208-108NBRTL 1 1/2
UEL209-112NBRTL 1 3/4
UC208NBRTL 40 2300 1600
UEL210NBRTL 50 2760 2010
UC209-112NBRTL 1 3/4 UC209NBRTL 45 2570 1810 UC210-200NBRTL 2 2760 2010 UC210NBRTL 50 UC211-200NBRTL 2
553400 2550
UC211NBRTLUC212NBRTL 60 4100 3150
Shaft Dia Load Rating Lb. (kg) Unit No. Unit No. Shaft Dia Load Rating Lb. (kg)
UC205NBRTL 25
PREMIUM TRIPLE LIP SEALGREASE PURGEABLE FOR HEAVY DUTYOR SPLASH APPLICATIONS
Triple Lip Seal
9
INSERT BEARINGS BEARINGS & HOUSINGS
ID OD W ID OD W ID OD W 10 26 8 6000DDUNBR 17 35 10 6003DDUNBR 30 55 13 6006DDUNBR 10 30 9 6200DDUNBR 17 40 12 6203DDUNBR 30 62 16 6206DDUNBR 10 35 11 6300DDUNBR 17 47 14 6303DDUNBR 30 72 19 6306DDUNBR 12 28 8 6001DDUNBR 20 42 12 6004DDUNBR 35 62 14 6007DDUNBR 12 32 10 6201DDUNBR 20 47 14 6204DDUNBR 35 72 17 6207DDUNBR 12 37 12 6301DDUNBR 20 52 15 6304DDUNBR 35 80 21 6307DDUNBR 15 32 9 6002DDUNBR 25 47 12 6005DDUNBR 40 68 15 6008DDUNBR 15 32 11 6202DDUNBR 25 52 15 6205DDUNBR 40 80 18 6208DDUNBR 15 42 13 6302DDUNBR 25 62 17 6305DDUNBR 45 75 16 6009DDUNBR
45 85 19 6209DDUNBR 45 100 17 6309DDUNBR
DIMENSIONS DIMENSIONS DIMENSIONS
6200 Series also available in C3
NBRBearing Number
NBRBearing Number
NBRBearing Number
inch mm5/8 AEL202-010NBR 40MS NBR 40MST NBR LF203 NBR 40PB NBR 47RPB 40PBS 3/4 AEL204-012NBR 47MS NBR 47MST NBR LF204 NBR 47PB NBR 52RPB 47PBS
20 AEL204NBR 47MS NBR 47MST NBR LF204 NBR 47PB NBR 52RPB 47PBS 7/8 AEL205-014NBR 52MS NBR 52MST NBR LF205 NBR 52PB NBR 62RPB 52PBS
1 AEL205-100NBR 52MS NBR 52MST NBR LF205 NBR 52PB NBR 62RPB 52PBS 25 AEL205NBR 52MS NBR 52MST NBR LF205 NBR 52PB NBR 62RPB 52PBS
1-1/8 AEL206-102NBR 52MS NBR 52MST NBR LF205 NBR 52PB NBR 62RPB 52PBS 1-3/16 AEL206-103NBR 62MS NBR 62MST NBR LF206 NBR 62PB NBR 72RPB 62PBS 1-1/4 AEL206-104NBR 62MS NBR 62MST NBR LF206 NBR 62PB NBR 62PBS
30 AEL206NBR 62MS NBR 62MST NBR LF206 NBR 62PB NBR 62PBS 1-1/4 AEL207-104NBR 72MS NBR 72MST NBR LF207 NBR 72PB NBR 72PBS 1-3/8 AEL207-106NBR 72MS NBR 72MST NBR LF207 NBR 72PB NBR 72PBS 1-3/8 AEL207-106NBR 72MS NBR 72MST NBR LF207 NBR 72PB NBR 72PBS
35 AEL207NBR 72MS NBR 72MST NBR LF207 NBR 72PB NBR 72PBS 72MS NBR 72MST NBR LF207 NBR 72PB NBR 72PBS
40 AEL208-NBR 80MS NBR 1-1/2 AEL208-108NBR 80MS NBR
BEARING NUMBEREN
(Ecc Lock)
SHAFT SIZE
MS platesalso available
trimmed
NARROW SERIES INSERT BEARINGS & HOUSINGS
AEL SERIES
NBR BALL BEARINGS6000 SERIES CONTACT SEAL
AEL(Eccentric Collar)
NOTE: 2-piece pressed metal housings. Supplied with contact seal for increased bearing protection.
30° 30°
Eccentric Collar Lock
METAL FACED SEAL
Metal Rubber Shield Seal (Green) (Black)
STANDARD
10
THERMOPLASTIC HOUSINGS THERMOPLASTIC BALL BEARING UNITS
NO PLATING OR COATING
Without a coating or plating process, the solid PBT housing will not scratch, chip or peel compared to coated or plated cast iron housings.
Cover type & colour : open or closed covers are available in either black or white.
Housing colour : housings are available in both Black and White. However, white is the standard stocked in Australia.
A WIDE VARIETY OF APPLICATION
The corrosion-resistant merits enable the NBR housing to become widely adopted and applied in many industries such as food processing, canning, bottling, chemical and pharmaceutical processing and many others.
All housings include stainless steel bolt hole inserts, to prevent deformation when being tightened down and come with a stainless steel grease nipple.
Made with Polybutylene (PBT) high-grade glass-filled thermoplastic polyester compared to conventional cast iron housings, NBR bearing housings are not only maintenance-free but are also excellent for stiffness and dimensional stabiltiy in heavy duty mechanical applications, a super light housing that will never rust or corrode.
FOOD SAFETY APPROVED
11
THERMOPLASTIC HOUSINGS THERMOPLASTIC BALL BEARING UNITS
In mm h a e b S2 S1 g w Bi n in mm
SUCP201-TF 201-008TF 202-TF
203-TF
1/2
5/8
12
15
17
1 3/1630.2
5127
3 3/495
1 1/238
3/419
1/213
15/3212
2 3/860
1.220531.0
0.720512.7 3/8 10
SUC201
202
203
P203-TF 0.78
SUCP204-TF 20 1 5/1633.3
5127
3 3/495
1 1/238
3/419
1/213
1/213
2 17/3264.3
1.220531.0
0.720512.7 3/8 10 SUC204 P204-TF 0.66
SUCP205-TF 7/8 15/16 1
251 7/16
36.55 1/2140
4 1/8105
1 1/238
3/419
1/213
1/213
2 25/3271
1.338634.1
0.563014.3 3/8 10
SUC205
P205-TF 0.86
SUCP206-TF 1 1/8 1 3/16 1 1/4
301 11/16
42.96 1/2165
4 3/4121
1 7/848
13/1621
21/3217
19/3216
3 5/1684
1.500038.1
0.626015.9 1/2 14 P206-TF 1.41
SUCP207-TF 1 1/4 1 5/16 1 3/8 1 7/16
35
1 7/847.6
6 9/16167
5127
1 7/848
13/1621
21/3217
5/816
3 21/3293
1.689042.9
0.689017.5 1/2 14 P207-TF 1.66
SUCP208-TF 1 1/2 1 9/16
40 1 15/1649.2
7 1/4184
5 13/32137
2 1/854
13/1621
21/3217
21/3217
3 27/3298
1.937049.2
0.748019.0 1/2 14 P208-TF 2.12
SUCP209-TF 1 5/8 1 11/16 1 3/4
452 1/854.0
7 15/32190
5 3/4146
2 1/854
13/1621
21/3217
21/3217
4 3/16106
1.937049.2
0.748019.0 1/2 14 P209-TF 2.40
SUCP210-TF 1 7/8 1 15/16
50 2 1/457.2
8 1/8206
6 1/4159
2 3/860
7/822
25/3220
3/419
4 7/16113
2.031551.6
0.748019.0 5/8 16 P210-TF 2.94
SUCP211-TF 2 2 1/8 2 3/16
552 1/263.5
8 5/8219
6 23/32171
2 3/860
7/822
25/3220
3/419
4 29/32125
2.189055.6
0.874022.2 5/8 16 P211-TF 3.66
SUCP212-TF 2 1/4 2 3/8 2 7/16
602 3/469.8
9 1/2241
7 1/4184
2 3/470
125
25/3220
7/822
5 7/16138
2.563065.1
1.000025.4 5/8 16 P212-TF 5.15
SUCP213-TF 65 376.2
10 7/16265
8203
2 3/470
1 3/1670
125
125
5 29/32150
2.563065.1
1.00025.4 3/4 20 P213-TF 6.10
SUCP214-TF 70 3 1/879.4
10 15/32266
8 9/32 2 27/3272
1 3/1630
125
1 3/3228
6 5/32156
2.937074.6
1.189030.2 3/4 20 P214-TF 6.90
SUCP215-TF
202-010TF
204-012TF
205-014TF 205-015TF 205-100TF
206-102TF 206-103TF 206-104TF
207-104TF 207-105TF 207-106TF 207-107TF
208-108TF 208-109TF
209-110TF 209-111TF 209-112TF
210-114TF 210-115TF
211-200TF 211-202TF 211-203TF
212-204TF 212-206TF 212-207TF
213-208TF
214-212TF
215-215TF 215-300TF
2 15/16 3
75 3 1/482.8
10 13/16275
8 17/32217
2 29/3274
1 3/1630
125
1 3/3228
6 3/8162
3.063077.8
1.311033.3 3/4 20 P215-TF 7.85
SUCP216-TF
SUCP217-TF
SUCP218-TF
HOUSINGNO.
Weightkg.
Bolt UsedBEARING
NO.UNIT NO.
3/4
2 1/2
2 3/4
Shaft Dia. Dimensions ( in )
( mm )
210
201-008NBRTL
202-010NBRTL
204-012NBRTL
SUC206
SUC207
SUC208
SUC209
SUC210
SUC211
SUC212
SUC213
SUC214
SUC215
205-014NBRTL 205-015NBRTL 205-100NBRTL
206-102NBRTL 206-103NBRTL 206-104NBRTL
207-104NBRTL 207-105NBRTL 207-106NBRTL 207-107NBRTL
208-108NBRTL 208-109NBRTL
209-110NBRTL 209-111NBRTL 209-112NBRTL
210-114NBRTL 210-115NBRTL
211-200NBRTL 211-202NBRTL 211-203NBRTL
212-204NBRTL 212-206NBRTL 212-207NBRTL
213-208NBRTL
214-212NBRTL
215-215NBRTL 215-300NBRTL
80 88.9 292 232 78 30 25 30 175 82.6 33.3 3/4 20 SUC216 P216-TF 9.00
85 95.2 310 247 83 30 25 32 187 85.7 34.1 3/4 20 SUC217 P217-TF 11.38
90 101.6 327 262 88 30 27 33 200 96.0 39.7 1 24 SUC218 P218-TF 13.46
PILLOW BLOCKS
SUCP200-TF SERIES
MATERIALS:Housing = POLYBUTYLENE (PBT)Bearing = Stainless Steel (AISI440C)
12
SUCF201-TF 201-008TF 202-TF 202-010TF 203-TF 204-TF 204-012TF
1/2
5/8
3/4
12
15
1720
3 3/886
2 33/6464
19/3215
15/3212
125.5
15/3212
1 5/1633.3
1.220531.0
0.500012.7
1 15/3237.0 3/8 10
SUC201
202
203 204
F204-TF 0.65
SUCF205-TF 205-014TF 205-015TF 205-100TF
7/8 15/16 1
253 3/4
952 3/4
705/816
9/1614
1 1/1627
15/3212
1 13/3235.8
1.342534.1
0.563014.3
1 9/1639.5 3/8 10 F205-TF 0.85
SUCF206-TF 206-102TF 206-103TF 206-104TF
1 1/8 1 3/16 1 1/4
304 1/4108
3 17/6483
45/6418
9/1614
1 7/3231
15/3212
1 37/6440.2
1.500038.1
0.626015.9
1 23/3244.0 3/8 10 F206-TF 1.15
SUCF207-TF 207-104TF 207-105TF 207-106TF 207-107TF
1 1/4 1 5/16 1 3/8 1 7/16
35
4 19/32117
3 5/892
3/419
5/816
1 11/3234
35/6414
1 3/444.4
1.689042.9
0.689017.5
1 29/3248.5 7/16 12 F207-TF 1.60
SUCF208-TF 208-108TF 208-109TF
1 1/2 1 9/16
40 5 1/8130
4 1/64102
53/6421
5/816
1 13/3236
5/816
2 1/6451.2
1.937049.2
0.748019.0
2 5/3256.0 1/2 14 F208-TF 2.05
SUCF209-TF 209-110TF 209-111TF 209-112TF
1 5/8 1 11/16 1 3/4
455 13/32
1374 9/64
10555/64
2223/32
181 1/2
385/816
2 1/1652.2
1.937049.2
0.748019.0
2 7/3256.0 1/2 14 F209-TF 2.38
SUCF210-TF 210-114TF 210-115TF
1 7/8 1 15/16
50 5 5/8143
4 3/8111
55/6422
23/3218
1 9/1640
5/816
2 5/3254.6
2.031551.6
0.748019.0
2 5/1658.5 1/2 14 F210-TF 2.50
SUCF211-TF 211-200TF 211-202TF 211-203TF
2 2 1/8 2 3/16
556 3/8162
5 1/8130
63/6425
25/3220
1 11/1643
3/419
2 19/6458.4
2.189055.6
0.874022.2
2 15/3262.5 5/8 16 F211-TF 3.60
SUCF212-TF 212-204TF 212-206TF 212-207TF
2 1/4 2 3/8 2 7/16
606 7/8175
5 5/8143
1 9/6429
25/2320
1 7/848
3/419
2 45/6468.7
2.563065.1
1.000025.4
2 7/873.0 5/8 16 F212-TF 5.15
SUCF213-TF 213-208TF 2 1/2
65 7 3/8187
5 55/64149
1 3/1630
25/3220
1 31/3250
3/419
2 3/469.7
2.563065.1
1.000025.4
2 29/3273.5 5/8 16 F213-TF 5.90
SUCF214-TF 214-212TF 2 3/4
70 7 19/32193
5 63/64152
1 7/3231
15/1624
2 1/854
3/419
2 31/3275.4
2.937074.6
1.189030.2
3 5/3280.0 5/8 16 F214-TF
SUCF215-TF 215-215TF 215-300TF
2 15/16 3
75 7 7/8200
6 17/64159
1 11/3234
15/1624
2 7/3256
3/419
3 3/3278.5
3.063077.8
1.311033.3
3 9/3283.0 5/8 16 F215-TF 6.80
SUCF216-TFSUCF217-TFSUCF218-TF
In m a e i g l s z Bi n t in mmHOUSING
NO.Weight
kg.BEARING
NO.UNIT NO.
Shaft Dia. Dimension
80 208 165 34 24 58 23 83.3 82.6 33.3 20 SUC216 F216-TF 8.2085 220 175 36 26 63 23 87.6 85.7 34.1 20 SUC217 F217-TF 9.3090 235 187 40 26 63 23 96.3 96.0 39.7 20 SUC218 F218-TF 11.30
6.30
Bolt Used(in) (mm)
201-008NBRTL
202-010NBRTL
204-012NBRTL
SUC206
SUC207
SUC208
SUC209
SUC210
SUC211
SUC212
SUC213
SUC214
SUC215
205-014NBRTL 205-015NBRTL 205-100NBRTL
206-102NBRTL 206-103NBRTL 206-104NBRTL
207-104NBRTL 207-105NBRTL 207-106NBRTL 207-107NBRTL
208-108NBRTL 208-109NBRTL
209-110NBRTL 209-111NBRTL 209-112NBRTL
210-114NBRTL 210-115NBRTL
211-200NBRTL 211-202NBRTL 211-203NBRTL
212-204NBRTL 212-206NBRTL 212-207NBRTL
213-208NBRTL
214-212NBRTL
215-215NBRTL 215-300NBRTL
SUC205
THERMOPLASTIC BALL BEARING UNITS THERMOPLASTIC BALL BEARING UNITS
FLANGE UNITS
SUCF200-TF SERIES
MATERIALS:Housing = POLYBUTYLENE (PBT)Bearing = Stainless Steel (AISI440C)
Additional sizes are available. Contact your nearest BSC store.
13
THERMOPLASTIC BALL BEARING UNITS THERMOPLASTIC BALL BEARING UNITS
FLANGE UNITS
SUCFL200-TF SERIES
In mm a e i g l s b z Bi n t in mmSUCFL201-TF 201-008TF 202-TF 202-010TF 203-TF 204-TF 204-012TF
1/2
5/8
3/4
12
15
1720
4 7/16113
3 35/6490
19/3215
7/1611
125.5
15/3212
2 3/860
1 5/1633.3
1.220531.0
0.500012.7
1 15/3237.0 3/8 10 FL204-TF 0.50
SUCFL205-TF 205-014TF 205-015TF 205-100TF
7/815/161
255 1/8130
3 57/6499
5/816
1/213
1 1/1627
5/816
2 11/1668
1 15/3235.7
1.342534.1
0.563014.3
1 9/1639.5 1/2 14 FL205-TF 0.70
SUCFL206-TF 206-102TF 206-103TF 206-104TF
1 1/81 3/161 1/4
305
13/16148
4 39/64117
45/6418
1/213
1 7/3231
5/816
3 5/3280
1 37/6440.2
1.500038.1
0.626015.9
1 23/3244.0 1/2 14 FL206-TF 0.98
SUCFL207-TF 207-104TF 207-105TF 207-106TF 207-107TF
1 1/41 5/161 3/81 7/16
356
11/32161
5 1/8130
3/419
9/1614
1 11/3234
5/816
3 17/3290
1 3/444.4
1.689042.9
0.689017.5
1 29/3248.5 1/2 14 FL207-TF 1.35
SUCFL208-TF 208-108TF 208-109TF
1 1/21 9/16
40 6 7/8175
5 43/64144
53/6421
9/1614
1 13/3236
5/816
3 15/16100
2 1/6451.2
1.937049.2
0.748019.0
2 5/3255.0 1/2 14 FL208-TF 1.69
SUCFL209-TF 209-110TF 209-111TF 209-112TF
1 5/81 11/161 3/4
457 13/32
1885 53/64
14855/64
2219/32
151 1/2
383/419
4 1/4108
2 1/1652.2
1.937049.2
0.748019.0
2 7/3256.0 5/8 16 FL209-TF 2.04
SUCFL210-TF 210-114TF 210-115TF
1 7/81 15/16
50 7 3/4197
6 3/16157
55/6422
19/3215
1 9/1640
3/419
4 17/32115
2 5/3254.6
2.031551.6
0.748019.0
2 5/1658.5 5/8 16 FL210-TF 2.30
SUCFL211-TF 211-200TF 211-202TF 211-203TF
22 1/82 3/16
558 13/16
2247 1/4184
63/6425
23/3218
1 11/1643
3/419
5 1/8130
2 19/6458.4
2.189055.6
0.874022.2
2 15/3262.5 5/8 16 FL211-TF 3.30
SUCFL212-TF 212-204TF 212-206TF 212-207TF
2 1/42 3/82 7/16
609 27/32
2507 61/64
2021 9/64
2923/32
181 7/8
4829/32
235 1/2140
2 45/6468.7
2.563065.1
1.000025.4
2 7/873.0 3/4 20 FL212-TF 4.30
SUCFL213-TF 213-208TF 2 1/2
65 10 5/32258
8 17/64210
1 3/1630
25/3220
1 31/3250
29/3223
6 3/32155
2 3/469.7
2.563065.1
1.000025.4
2 29/3273.5 3/4 20 FL213-TF 5.40
SUCFL214-TF 214-212TF 2 3/4
70 10 7/16 8 1/2216
1 7/3231
7/822
2 1/854
29/3223
6 5/16160
2 31/3275.4
2.937074.6
1.18930.2 3/4 20 FL214-TF 5.60
SUCFL215-TF 215-215TF 215-300TF
2 15/163
7510 13/16
2758 55/64
2251 11/32
347/822
2 7/3256
29/3223
6 1/2165
3 3/3278.5
3.063077.8
1.311033.3
5/8 16 FL215-TF 6.20
SUCFL216-TF 80 290 233 34 22 58 25 180 83.3 82.6 33.3 20 SUC216 FL216-TF 7.80
Weightkg.
UNIT NO.Shaft Dia. Dimension B Bolt Used BEARING
NO.HOUSING
NO.
265
(in) (mm)
SUC201
202
203 204
201-008NBRTL
202-010NBRTL
204-012NBRTL
SUC206
SUC207
SUC208
SUC209
SUC210
SUC211
SUC212
SUC213
SUC214
SUC215
205-014NBRTL 205-015NBRTL 205-100NBRTL
206-102NBRTL 206-103NBRTL 206-104NBRTL
207-104NBRTL 207-105NBRTL 207-106NBRTL 207-107NBRTL
208-108NBRTL 208-109NBRTL
209-110NBRTL 209-111NBRTL 209-112NBRTL
210-114NBRTL 210-115NBRTL
211-200NBRTL 211-202NBRTL 211-203NBRTL
212-204NBRTL 212-206NBRTL 212-207NBRTL
213-208NBRTL
214-212NBRTL
215-215NBRTL 215-300NBRTL
SUC205
MATERIALS:Housing = POLYBUTYLENE (PBT)Bearing = Stainless Steel (AISI440C)
Additional sizes are available. Contact your nearest BSC store.
14
NBR BEARING MOUNTING METHODS
Set Screw Method
Two knurled cup-point, self locking, socket-head set screws fitted at 120° apart in the extended inner ring of the bearing insert.
For standard loads and moderate speeds, mount the bearing unit into position and tighten down the set screw to the recommended torque value. Additional security can be achieved by spot drilling the shaft to accommodate the set screw point. Using the correct size of socket head wrench, tighten the set screw to recommended torque. Eccentric Lock Collar Method
Here, an eccentric diameter formed on the extended inner ring of the bearing which engages a similarly formed eccentric diameter in the bore of a separate collar.
Locking is achieved by turning the collar in the direction of shaft rotation until the eccentric diameters of both collar and inner ring are fully engaged. The collar is provided with a blind hole to facilitate tightening when locking the bearing to the shaft. The set screw when tightened to the recommended torque value prevents the collar backing off in service.
Adapter Sleeve Method
This consists of a standard adapter sleeve, locknut and lock washer.
When fitting the bearing to the shaft, care must be taken to ensure that the locknut is not over tightened as this can reduce or eliminate the required bearing internal clearance, resulting in premature failure.
The proper tightening condition can be obtained, firstly by tightening the locknut by hand and then rotating 2/5 to 3/5 revolutions by a spanner.
A lock washer is provided which prevents the lock nut backing off when one of the tabs is engaged with the corresponding notch in the locknut.
Mounting on Shaft
TABLE 1. Tightening Torque for Set ScrewBearing Number Set Screw Tightening TorqueAS201~ AS203UCS201~UCS203
M 5X0.8 30
AS204~ AS207UCS204~UCS206UC201~UC206(SUC201~SUC206)UCX05UC305~UC306
M 6X1 40
AS208UCS207~UCS209UC207~UC209(SUC207~SUC209)UCX06~UCX08UC307
M 8X1 85
UCS210~UCS212UC210~UC212(SUC210~SUC212)UCX09~UCX11UC308~UC309
M 10X1.25 175
UC2213~UC218UCX12~UCX17UC310~UC314
M 12X1.5 280
UC315~UC316 M 14X1.5 350
UC317~UC319 M 16X1.5 560
UC320 M 18X1.5 620
TABLE 2. Shaft Selection
Shaft Dia(mm)
Shaft Tolerance (m)
j6 h6 h7 h8
Over incl max min max min max min max min
1018305080120
18305080120180
+ 8+ 9+ 11+ 12+ 13+ 14
- 3- 4- 5- 7- 9- 11
000000
- 11- 13- 16- 19- 22- 25
000000
- 18- 21- 25- 30- 35- 40
000000
- 27- 33- 39- 46- 54- 63
Limit of dn value
above 120000
above 100000up to 120000
above 60000up to 100000
60000 and below
dn value = d (shaft diameter in mm) x n (speed in rpm)
Mounting Housing
To prevent any damage to the insert bearing due to faulty installation, housing units should always be bolted to a base which is to be flat and rigid. The bearing center alignment angle of +3° is required for the mounting base. In case of bearing units with cover, this angle is restricted to +1°.
Shaft Selection
Below is a table to provide you with the dimensional accuracy of your shaft to be made for loose fit in order to facilitate its smooth running.
BALL BEARING UNITS SPLIT HOUSINGS
15
SN
COMPATIBLE
PEDESTAL
Conversion from solid bearing to Cooper splitroller bearings is easy.
The SN compatible pedestal range offersthe advantages of quick access, ease ofchange and low maintenance cost benefitsof Cooper split bearing technology to bothOEM’s and end users.
Dimensionally Interchangeable with SN 500 HousingsEasier, Cost Effective MaintenanceSuperior Sealing Capability
Sp
ecify
ing
Co
op
er
r ep
oo
C gn
iyfi
cep
S
BALL BEARING UNITS SPLIT HOUSINGS
16
Assembled toOrder
Double row spherical rollerbearing acceptsmisalignment
Choice of 5 superiorprimary seals available inany combination.
Solid Foot Construction
The ends of our feet are precisionmachined true to the bore of thehousing for precise blocking andalignment
2-Bolt and 4-bolt pillowblocks available
Housings can be special ordered withnickel, zinc or Urethane coating
Optional snap on secondaryseals available
Easily converted tofixed or expansion inthe field
External nuteliminatesaxialmovement
Housings manufacturedfrom 75,000 psi tensilecast steel, can berebuilt several times
Pillow Block Bearings
EC - Eccentric LockAccepts heavy thrust loads
CL - Set Screw LockAccepts light thrust loads
DV / TATaperedAdapterLock
EC Series -Eccentric Locking Collar
Unsurpassed for holding inheavy thrust, reversing orshock loading.
We guarantee this bearingwill not come loose ifinstalled on a precisionground shaft.
CL Series -Concentric LockingCollar (set screw lock)
Set screw locking 2 setscrews @ 60º, providesmaximum holding withminimal run out. Knurledpoint set screws providepositive locking.
DV Series -Tapered AdapterSleeve
DV Bearings are adrop in replacementfor common AmericanSet-screw mountedunits, results inextremely high loadcapacities comparedto any collar mountedunit. Best concentricityfor high speeds.
TA Series -Tapered AdapterSleeve
TA Bearings are adirect drop inreplacement for SAF/SN split cap housingdimensionsresults in superiorsealing and integrallyrobust housing. Bestconcentricity for highspeeds.
We Guarantee oursteel housings for life
against breakage.
EC Bearingshown above
PILLOW BLOCK BEARINGS PILLOW BLOCK BEARINGS
17
IMPERIALSN Unit
NOShaftSize
QMSNPart NO
BearingNO
SN510 1-3/4 QMSN09J112ST 22209
SN511 1-15/16 QMSN10J115ST 22210
SN511 2 QMSN10J200ST 22210
SN513 2-3/16 QMSN10J203ST 22211
SN513 2-1/4 QMSN10J204ST 22211
SN515 2-7/16 QMSN13J207ST 22213
SN515 2-1/2 QMSN13J208ST 22213
SN516 2-11/16 QMSN15J211ST
SN516 2-3/4 QMSN15J212ST 22215
SN517 2-15/16 QMSN15J215ST 22215
SN517 3 QMSN15J300ST 22215
3-3/16 QMSN18J303ST
SN518 3-1/4 QMSN15J304ST 22218
SN520 3-7/16 QMSN18J307ST
SN520 3-1/2 QMSN18J308ST 22218
SN522 3-11/16 QMSN20J311ST
SN522 3-15/16 QMSN20J315ST 22220
SN522 4 QMSN20J400ST 22220
SN526 4-1/2 QMSN22B408ST 22222
SN528 5 QMSN26B500ST 22226
PRE-ASSEMBLED UNITS, NO SET-UP REQUIRED
METRICSN Unit
NOShaftSize
QMSNPart NO
BearingNO
SN509 40mm QMSN09J040ST 22209
SN510 45mm QMSN09J045ST 22209
SN511 50mm QMSN10J050ST 22210
SN512 55mm QMSN10J055ST 22211
SN513 60mm QMSN13J060ST 22213
SN515 65mm QMSN13J065ST 22213
SN516 70mm QMSN15J070ST 22215
SN517 75mm QMSN15J075ST 22215
SN518 80mm QMSN15J080ST 22218
SN520 85mm QMSN18J085ST
SN520 90mm QMSN18J090ST 22218
SN522 100mm QMSN20J100ST 22220
SN524 110mm QMSN22B110ST 22222
SN528 125mm QMSN26B125ST 22226
Conversion Chart
PILLOW BLOCK BEARINGS PILLOW BLOCK BEARINGS
2-BOLT PILLOW BLOCK
SN,SNL,SNA and SNG to QMSN SN STYLE
18
QM Blue Brute EC Series BearingsBearingPart NO
ShaftSize
BRGNO
A B C Emin
Emax
F G H J K L M R S Wtlbs
QMSN09J040S 40mm
22209 60 111 67 159 175 205 62 35 12 25 78 48 5 73 22QMSN09J111S 1-11/16”QMSN09J112S 1-3/4”QMSN09J045S 45mmQMSN10J115S 1-15/16”
22210 70 130 70 183 216 254 68 25 16 25 82 48 9 73 26QMSN10J200S 2”QMSN10J050S 50mmQMSN11J203S 2-3/16”
22211 70 130 76 183 216 254 68 25 16 29 85 51 6 80 26QMSN11J204S 2-1/4”QMSN11J055S 55mmQMSN13J060S 60mm
22213 80 159 92 196 235 275 74 35 16 31 91 55 4 89 32QMSN13J207S 2-7/16”QMSN13J208S 2-1/2”QMSN13J065S 65mmQMSN15J211S 2-11/16”
22215 95 183 102 241 279 316 76 34 20 32 98 60 6 92 41
QMSN15J212S 2-3/4”QMSN15J070S 70mmQMSN15J215S 2-15/16”QMSN15J300S 3”QMSN15J075S 75mmQMSN18J303S 3-3/16”
22218 100 193 121 279 292 345 84 39 20 37 106 66 4 102 50QMSN18J304S 3-1/4”QMSN18J080S 80mmQMSN18J085S 85mm 22218 112 205 121 279 292 345 84 39 20 37 106 66 4 102 50QMSN18J307S 3-7/16”
22218 112 212 121 290 327 380 84 39 24 37 106 66 4 102 50QMSN18J308S 3-1/2”QMSN18J090S 90mmQMSN20J311S 3-11/16”
22220 125 238 152 319 366 410 101 50 24 41 126 75 9 117 69QMSN20J312S 3-3/4”QMSN20J315S 3-15/16”QMSN20J400S 4”QMSN20J100S 100mmQMSN22B110S 110mm 22222 140 253 160 332 365 410 111 39 24 41 147 75 6 117 69QMSN22B407S 4-7/16”
22222 150 263 160 367 400 445 111 49 24 47 147 94 6 140 78QMSN22B408S 4-1/2:QMSN22B115S 115mmQMSN26B125S 125mm
22226 150 282 175 402 435 500 113 49 30 56 155 92 7 148 78QMSN26B415S 4-15/16”QMSN26B500S 5”QMSN26B130S 130mm
PILLOW BLOCK BEARINGS PLUMMER BLOCKS
2-BOLT PILLOW BLOCK
QMSN SN STYLE, Eccentric Lock
19
SEALING ARRANGEMENT SUFFIX
1. Std Felt Groove -2. ‘Z’ Seal ‘Z’3. Triple Seal Vertical Labyrinth Collars:- i) Inch ‘TSE’ ii) Metric ‘TSM’
4. Face Seal Horizontal Labyrinth Collars:- i) Inch ‘LSE’ ii) Metric ‘LSM’
5. Face Seal and Wiping Lip Horizontal Labyrinth Collars:- i) Inch ‘LSE’ Z ii) Metric ‘LSM’ Z
6. Face Seal and Wiping Lip Horizontal Labyrinth Collars Grease Purge Sealing:- i) Inch ‘LSE’ TAC ii) Metric ‘LSM’ TAC
7. Triple Seal Combination Labyrinth Collar and Wiping Lip Grease Purge Sealing:- i) Inch ‘TSE’ TAC ii) Metric ‘TSM’ TAC
HOUSING SIZE
The first figure designates the series.
1. ‘500’ Normal Duty2. ‘600’ Heavy Duty
The last two figures designate the final twodigits of the Bearing Number.
BEARING AND ADAPTER SLEEVE
Selected Bearing from HousingTables with Adapter Sleeve.
Example:- 22211 K + H 311
MATERIAL SUFFIX
Grey Cast Iron toAUST. STD G8 Grade 14(Colour Code - Grey)
‘SG’ Spheroidal Graphitic Iron toAUST STD G9 Grade SNG 32/7 ‘SG’(Colour Code - Orange)
‘S’ Cast Steel ‘S’(Colour Code - Black)
MISCELLANEOUS SUFFIX
Drilled Relief Hole no Slinger Disc. G.H.Housings supplied with Grease G.V.Relief Slinger Disc.Housings required with Oil Lubrication should be specified
CLOSED HOUSINGS SUFFIX
I.E 1 Side Open1 Side Closed ‘A’
OPEN HOUSINGS SUFFIX
I.E Both Sides Open ‘B’
SPLIT HOUSINGS
‘SN’ Medium Duty‘SSN’ Heavy Duty
Solid Base Undrilled‘SD’ Large Series for 231 Series
Bearings
NON-SPLIT HOUSINGS
‘SB’ Medium Duty Block‘WB’ Heavy Duty Block‘FC’ Square Flanged Housing‘RFS’ Spigot Flanged Housing
‘CFCN’ Spigot Circular FlangedHousing
‘TH’ Take-Up Housing
PREFIX BASE SECURINGBOLT HOLES
- ‘SN’ Cast 2 Bolt Slot Standard - ‘SSN’ Solid Base Undrilled T ‘SSN’ 2 Bolt Hole Drilled F ‘SSN’ 4 Bolt Hole Drilled
‘SD’ Cast 4 Bolt Hole Standard - ‘SSD’ Solid Base Undrilled T ‘SSD’ 2 Bolt Hole Drilled F ‘SSD’ 4 Bolt Hole Drilled
* F S SN 511 A TS E GH SG 22211 K + H311
FOUR SOLID SPLIT SIZE CLOSED T RIPLE ENGLISH GREASE MATERIAL BEARING ADAPTERBOLT BASE PLUMMER HOUSING SEAL ENTRY HOLE NO. SLEEVE
SECURING BLOCK LABYRINTH (INCHES) NO.COLLAR
PREFIX BASIC HOUSINGDESIGNATION
* THIS SEQUENCE OF DESIGNATION SHOULD BE FOLLOWED WHEN ORDERING BSC TRANSMISSION BEARINGS
PILLOW BLOCK BEARINGS PLUMMER BLOCKS
BSC HOUSINGS DESIGNATION SYMBOLS
20
SNG500 SERIES
IN MM H (h12) a e b u v c W L d1 (H12) d2 (H12) n J F g (H12) Da (H8) 2 4 Number Qty 1-1/8 30 50 185 150 52 13 20 22 92 82 46.5 54.5 7.5 5 34 72 M10 1207K H207 SR72 x 8.5 2 2.64 22207K H307 SR72 x 5.5 2
SNG508-607 1-1/4 35 60 205 170 60 15 20 25 106 85 51.5 59.5 7.5 5 39 80 M12 1208K H208 SR80 x 10.5 2 3.52 22208K H308 SR80 x 8 2 SNG509 1-1/2 40 60 205 170 60 15 20 25 109 85 56.5 64.5 8.5 5 30 85 M12 1209K H209 SR85 x 5.5 2 3.85 22209K H309 SR85 x 7 1 SNG510-608 1-3/4 45 60 205 170 60 15 20 25 112 90 62 70.5 8.5 5 41 90 M12 1210K H210 SR90 x 10.5 2 3.85 22210K H310 SR90 x 9 2 SNG511-609 2 50 70 255 210 70 18 23 28 127 95 67 75.5 35 8.5 5 44 100 M16 M12 1211K H211 SR100 x 11.5 2 5.7 22211K H311 SR100 x 9.5 2 SNG512-610 2-1/8 55 70 255 210 70 18 23 30 133 105 72 80.5 35 8.5 5 48 110 M16 M12 1212K H212 SR110 x 13 2 7.4 22212K H312 SR110 x 10 2 SNG513-611 2-1/4 60 80 275 230 80 18 24 30 148 110 77 85.5 35 8.5 5 51 120 M16 M12 1213K H213 SR120 x 14 2 8.7 22213K H313 SR120 x 10 2 SNG515-612 2-1/2 65 80 280 230 80 18 26 30 154 115 87 95.5 40 8.5 5 56 130 M16 M12 1215K H215 SR130 x 15.5 2 8.5 22215K H315 SR130 x 12.5 2 SNG516-613 2-3/4 70 95 315 260 90 22 29 32 175 120 92.5 101 40 11 5 58 140 M20 M12 1216K H216 SR140 x 16 2 12.1 22216K H316 SR140 x 12.5 2 SNG517 3 75 95 320 260 90 22 30 32 181 125 97.5 106 50 11 5 61 150 M20 M12 1217K H217 SR150 x 16.5 2 14 22217K H317 SR150 x 12.5 2 SNG518-615 3-1/4 80 1218K H218 SR160 x 17.5 2 16.3 100 345 290 100 22 27 35 192 140 102.5 111 50 11 5 65 160 M20 M16 22218K H318 SR160 x 12.5 2 23218K H2318 SR160 x 12.5 1 SNG519-616 85 112 345 290 100 22 27 35 209 145 131 141 50 12 6 68 170 M20 M16 1219K H219 SR170 x 18 2 17 22219K H319 SR170 x 12.5 2 SNG520-617 3-1/2 90 1220K H220 SR180 x 18 2 112 380 320 110 26 32 40 215 160 137.5 147.5 60 12 6 70 180 M24 M16 22220K H320 SR180 x 12 2 20.2 23220K H2320 SR180 x 9.7 1 SNG522-619 4 100 1222K H222 SR200 x 21 2 125 410 350 120 26 32 45 239 175 147.5 157.5 70 12 6 80 200 M24 M16 22222K H322 SR200 x 13.5 2 27.3 23222K H2322 SR200 x 10.2 1 SNG524-620 4-1/4 110 140 410 350 120 26 32 45 271 185 157.5 167.5 70 12 6 86 215 M24 M16 22224K H3124 SR215 x 14 2 35.5 23224K H2324 SR215 x 10 1 SNG526 4-1/2 115 150 445 380 130 28 35 50 290 190 167.5 177.5 70 13 6 90 230 M24 M20 22226K H3126 SR230 x 13 2 44 23226K H2326 SR230 x 10 1 SNG528 5 125 150 500 420 150 35 42 50 302 205 177.5 187.5 80 13 6 98 250 M30 M24 22228K H3128 SR250 x 15 2 54 23228K H2328 SR250 x 10 1 SNG530 5-1/4 135 160 530 450 160 35 42 60 323 220 192.5 202.5 90 14 6 106 270 M30 M24 22230K H3130 SR270 x 16.5 2 61.5 23230K H2330 SR270 x 10 1 SNG532 5-1/2 140 170 550 470 160 35 42 60 344 235 202.5 212.5 90 14 6 114 290 M30 M24 22232K H3132 SR290 x 17 2 69.5 23232K H2332 SR290 x 10 1
WEIGHTKG
LOCATION RING
SNG507-606
SHAFT DIA DIMENSION (MM)HOUSING NO
S BEARINGNO
ADAPTERSLEEVE
PLUMMER BLOCKS FLANGED HOUSINGS
21
PLUMMER BLOCKS FLANGED HOUSINGS
FCM500 SERIES
HOUSING NO SHAFT DIA, d HOUSING BEARING ADAPTER mm A E C G L L1 X Y S WEIGHT [kg] NO SLEEVE SIZE QTY
FCM506 25 127 95 90 14 72 – 51 18 11 2.31206K 2206K 22206K
H206 H306 H306
62 x 7 62 x 10 62 x 10
2 1 1
FCM507 30 130 100 97 14 75 85 52 18 11 2.81207K 2207K22207K
H207 H307 H307
72 x 7 72 x 8 72 x 8
2 1 1
FCM508 35 136 105 108 14 77 87 59 18 11 3.21208K 2208K22208K
H208 H308 H308
80 x 7.5 80 x 10 80 x 10
2 1 1
FCM509 40 136 105 113 14 79 89 62 21 14 3.21209K 2209K 22209K
H209 H309 H309
85 x 6 85 x 8 85 x 8
2 1 1
FCM510 45 142 108 118 15 83 93 60 21 14 3.71210K 2210K 22210K
H210 H310 H310
90 x 6.5 90 x 10 90 x 10
2 1 1
FCM511 50 160 124 128 15 89 99 67 26 18 5.21211K 2211K 22211K
H211 H311 H311
100 x 6 100 x 8 100 x 8
2 1 1
FCM512 55 170 130 142 18 93 103 71 25 18 6.21212K 2212K 22212K
H212 H312 H312
110 x 8 110 x 10 110 x 10
2 1 1
FCM513 60 180 140 150 20 96 106 76 23 18 7.61213K 2213K 22213K
H213 H313 H313
120 x 10 120 x 12 120 x 12
2 1 1
FCM515 65 190 152 162 20 102 112 78 29 18 91215K 2215K 22215K
H215 H315 H315
130 x 8 130 x 10 130 x 10
2 1 1
FCM516 70 196 152 176 22 107 117 82 28 18 9.21216K 2216K 22216K
H216 H316 H316
140 x 8.5 140 x 10 140 x 10
2 1 1
FCM517 75 210 170 188 22 111 121 88 29 18 121217K 2217K22217K
H217 H317 H317
150 x 9 150 x 10 150 x 10
2 1 1
FCM518 80 210 170 198 22 129.4 144.4 112 31 18 15
1218K 2218K 22218K 23218K
H218 H318 H318 H2318
160 x 16.2 160 x 11.2 160 x 11.2 160 x 10
2 2 2 1
FCM520 90 250 198 220 25 147 162 123 33 22 20.3
1220K 2220K22220K 23220K
H220 H320 H320 H2320
180 x 18.1 180 x 12.1 180 x 12.1 180 x 10
2 2 2 1
FCM522 100 270 219 240 25 156 171 133 32 22 25.8
1222K 2222K 22222K 23222K
H222 H322 H322 H2322
200 x 21 200 x 13.5 200 x 13.5 200 x 10.
2 2 2 1
FCM524 110 280 230 262 28 165 183 141 35 26 2922224K 23224K
H3124 H2324
215 x 14 215 x 10
2 1
FCM526 115 305 250 280 30 174 192 150 39 26 3522226K 23226K
H3126 H2326
230 x 13 230 x 10
2 1
FCM528 125 330 270 300 30 186 204 162 43 26 4222228K 23228K
H3128 H2328
250 x 15 250 x 10
2 1
FCM530 135 350 290 320 40 183 201 170 39 32 48.422230K 23230K
H3130 H2330
270 x 16.5 270 x 10
2 1
FCM532 140 370 300 340 42 197 215 180 38 32 56.422232K 23232K
H3132 H2332
290 x 17 290 x 10
2 1
LOCATING RING DIMENSIONS [MM]
22
Procedure for Mounting Spherical Roller Bearingswith Tapered Bore and using an Adapter Sleeve
1 Unwrap bearing and inspect for internal clearancegroup. When supplied with housings they willusually be “Normal Clearance” - no suffix afternumber - or, “C3 Clearance” one group greater thannormal. Multiply last two numerals of bearingnumber by 5 to determine nominal bore size inmillimetres.
Example: 22232 = 32 x 5 = 160mm Nominal Bore (bearing bore)
2 Measurebearing withfeeler gaugesand note actualinternalclearance. Tworollers should belined up side by
side at top of the bearing andprogressively larger feelers slidbetween rollers and outer raceuntil beginning of interferenceis felt. Under no circumstancesshould bearing be rotated to“roll” feelers through - this willresult in an erroneous reading.
3 From “Actual Clearance” measured, subtract “Decrease in Radial Clearance”from column B of TABLE 1 below to obtain required “Residual Clearance”.
Example : 22232KC3 is measured at .230mm actual clearance whichfalls within the I.S.O. standard actual clearance range of .180 to.230mm. The “Decrease in Radial Clearance” for 22232KC3 columnreads .075 to .100mm. Therefore the “Residual Clearance” range, whichis what the bearing should measure within after tightening adapter, is :-Max = (.230 - .075) = .155mm and Min = (.230 - .100) = .130mm.
10 Housing cap, after cleaning, can be assembled to bodies (not interchange-able). Feeler gauge should be “tried” between housing base and frame padto ensure flatness and that shims are not required. Base bolts can betightened. Check that rotation is free and not impaired. Taconite sealsshould be fitted. Adjust housing base alignment to allow constant clearancearound circumference of rotating labyrinth and taconite cover body. Sealsshould be lubricated until grease extrudes fully around labyrinth circumfer-ence. DO NOT “overgrease” bearing housing as damage and overheatingcan occur during initial running period.
8 The floating bearing should bepositioned slightly off housing centretoward locknut side of sleeve so that asnut is tightened, bearing will bedisplaced approximately back to centreline. No spacer rings are used.
9 Grease should be “worked” into bearing for as much of circumference aspossible, rotating occasionally. Basic grease capacity rule is that 1/2 - 1/3of housing volumetric capacity be filled. This can be done by hand prior tofitting cap which can be “plugged” and only the taconite seals lubricated vianipples on a regular basis.
High temperature or unusual applications may require a special greaseselection and should be referred to your nearest BSC branch.
SUITABLE LUBRICANTS: Shell - ALvania R2, EP2BP - Energrease LS2, LSEP2Mobil - Grease 77, Mobilux EP2Ampol - RRs, EP Grease C2Caltex - Regal, Starfak, Premium 2
5 Bearings, adapter sleeves,rotating seal componentsand solid spacer ringsshould be fitted loosely toshaft in approximatelyrequired positions. Thetaconite seals (with outercasting) can be positionedalready assembled.Otherwise, rotatinglabyrinth and oil seal canbe positioned loosely.
7 When bearings are in position,the adapter sleeves can betightened. Fixed bearing shouldbe tightened first, “C” spannersshould be used where possible.Progressively, tighten locknutwhilst feeler gauge readings aretaken to achieve desired“Residual Clearance”.
6 After cleaning, set upbases in position. Fit basebolts (if on base frame) butleave loose so that bases canbe moved later to providecorrect shaft alignment.Lower bearings and shaftassembly into positioncarefully, re-spacingcomponents as required.
4 Bearings should be “located” or “fixed” in one housing and allowed to “float”in the other. Therefore, spacer rings will be used in one housing only. One ortwo spacer rings are used according to bearing size. If one is used, it shouldbe located on locknut size. If two, they should be positioned each side ofbearing.
Two types of spacer rings commonly used are Solid (fully circular) and Gaptypes.
A B C DBearing bore Decrease in Axial Min. permissible
diameter rad1al internal displacement residuald clearance Taper 1:12 clearance
over incl. min max min max Normal C330 40 0.020 0.025 0.35 0.4 0.015 0.02540 50 0.025 0.030 0.4 0.45 0.020 0.03050 65 0.030 0.040 0.45 0.6 0.025 0.03565 80 0.040 0.050 0.6 0.75 0.025 0.04080 100 0.045 0.060 0.7 0.9 0.035 0.050
100 120 0.050 0.070 0.75 1.1 0.050 0.065120 140 0.065 0.090 1.1 1.4 0.055 0.080140 160 0.075 0.100 1.2 1.6 0.055 0.090160 180 0.080 0.110 1.3 1.7 0.060 0.100180 200 0.090 0.130 1.4 2.0 0.070 0.100200 225 0.100 0.140 1.6 2.2 0.080 0.120225 250 0.110 0.150 1.7 2.4 0.090 0.130250 280 0.120 0.170 1.9 2.7 0.100 0.140280 315 0.130 0.190 2.0 3.0 0.110 0.150315 355 0.150 0.210 2.4 3.3 0.120 0.170355 400 0.170 0.230 2.6 3.6 0.130 0.190400 450 0.200 0.260 3.1 4.0 0.130 0.200450 500 0.210 0.280 3.3 4.4 0.160 0.230500 560 0.240 0.320 3.7 5.0 0.170 0.250560 630 0.260 0.350 4.0 5.4 0.200 0.290630 710 0.300 0.400 4.6 6.2 0.210 0.310710 800 0.340 0.450 5.3 7.0 0.230 0.350
TABLE 1. Standard Tolerance Values
a
b
or
MOUNTING PROCEDURE SEALING ARRANGEMENTS
23
SEALING ARRANGEMENTS
Consider “SNG” Housings for Improved Sealing
MOUNTING PROCEDURE SEALING ARRANGEMENTS
BSC BRANCH LOCATOR
Please Note: This publication has been prepared as a general reference guide only. While the information in this publication with respect to competitive products has been carefully compiled from the trade publications available, Bearing Service Pty. Ltd. does not accept any responsibility or liability whatsoever for the accuracy of the information contained in the trade publications from which the information in this publication has been derived. Where reference is made to parts that may be used in substitution for each other, Bearing Service Pty. Ltd. does not intend to imply that those parts are necessarily of the same standard and quality. Bearing Service Pty. Ltd. makes no representation that one product may be used to replace the other. Bearing Service Pty. Ltd. represents only that each of the units so mentioned are intended by the respective manufacturer thereof to be used for the same purpose.
bsc stores locator
COOPER SPLIT BEARINGS
NEW SOUTH WALES
SYDNEY (MOOREBANK) Phone: (02) 9824 2100 Fax: (02) 9824 2143 ARMIDALE Phone: (02) 6772 5511 Fax: (02) 6772 8881 ARNDELL PARK (Bearing Traders) Phone: (02) 9622 9322 Fax: (02) 9622 9377 BALLINA Phone: (02) 6686 4455 Fax: (02) 6686 4687 BOOROWAPhone: (02) 6385 3695 Fax: (02) 6385 3922CANBERRA (FYSHWICK)Phone: (02) 6280 7517 Fax: (02) 6280 7041 COFFS HARBOUR Phone: (02) 6651 2813 Fax: (02) 6651 2758 CONDOBOLIN Phone: (02) 6895 2137 Fax: (02) 6895 3859 COOMA Phone: (02) 6452 4366 Fax: (02) 6452 4377 COONAMBLE Phone: (02) 6822 1899 Fax: (02) 6822 2340 COOTAMUNDRAPhone: (02) 6942 4255 Fax: (02) 6942 1214COROWAPhone: (02) 6033 1897 Fax: (02) 6033 3448COWRA Phone: (02) 6341 2244 Fax: (02) 6341 2144 DUBBO Phone: (02) 6884 5545 Fax: (02) 6884 2383 DUBBO EASTPhone: (02) 6882 6888 Fax: (02) 6884 1308EDENPhone: (02) 6496 1345 Fax: (02) 6496 3275FORBES Phone: (02) 6852 3211 Fax: (02) 6852 2978 GILGANDRA Phone: (02) 6847 2075 Fax: (02) 6847 1295 GRAFTON NORTHPhone (02) 6642 2666 Fax: (02) 6643 1281GRAFTON SOUTHPhone (02) 6642 4588 Fax: (02) 6642 4836GRIFFITHPhone: (02) 6964 3711 Fax: (02) 6964 1908GUNNEDAH Phone: (02) 6742 2855 Fax: (02) 6742 3453 HARDENPhone: (02) 6386 3526 Fax: (02) 6386 2510LISMORE Phone: (02) 6621 2337 Fax: (02) 6621 9141 LEETONPhone: (02) 6953 4233 Fax: (02) 6953 3807MOREEPhone: (02) 6752 2218 Fax: (02) 6752 2310 MURWILLUMBAHPhone: (02) 6672 4533 Fax: (02) 6672 6811 MUSWELLBROOKPhone: (02) 6543 2466 Fax: (02) 6543 4242 NARRABRIPhone: (02) 6792 1988 Fax: (02) 6792 2629 NARROMINEPhone: (02) 6889 1588 Fax: (02) 6889 1253 NEWCASTLEPhone: (02) 4954 6877 Fax: (02) 4954 6861 NOWRA Phone: (02) 4421 3233 Fax: (02) 4421 2632 NYNGAN Phone: (02) 6832 1577 Fax: (02) 6832 2094 ORANGEPhone: (02) 6362 3555 Fax: (02) 6362 5272 OURIMBAHPhone: (02) 4389 1787 Fax: (02) 4389 1965PARKESPhone: (02) 6862 5011 Fax: (02) 6862 5066PORT MACQUARIEPhone: (02) 6581 0300 Fax: (02) 6581 0311
QUEENSLAND
BRISBANE (NORTHGATE) Phone: (07) 3866 8333 Fax: (07) 3260 7590 ARCHERFIELD Phone: (07) 3277 4488 Fax: (07) 3277 8350 ATHERTON Phone: (07) 4091 5902 Fax: (07) 4091 5904AYR Phone: (07) 4783 6900 Fax: (07) 4783 5750BILOELAPhone: (07) 4992 1099 Fax: (07) 4992 1590BOONAHPhone: (07) 5463 1044 Fax: (07) 5463 2617BUNDABERG Phone: (07) 4153 3220 Fax: (07) 4153 1744 CABOOLTURE Phone: (07) 5495 6266 Fax: (07) 5495 6634 CAIRNS Phone: (07) 4225 3100 Fax: (07) 4225 3199 CHARLEVILLE Phone: (07) 4654 2355 Fax: (07) 4654 2501CHINCHILLA Phone: (07) 4669 1244 Fax: (07) 4051 0961DALBY Phone: (07) 4662 4488 Fax: (07) 4662 3466 GATTON Phone: (07) 5462 1177 Fax: (07) 5462 3329GATTONPhone: (07) 5462 1266 Fax: (07) 5462 3390GOONDIWINDI Phone: (07) 4671 1396 Fax: (07) 4671 3823 GYMPIEPhone: (07) 5482 4122 Fax: (07) 5482 7982HERVEY BAY Phone: (07) 4124 0999 Fax: (07) 4124 0555 INNISFAILPhone: (07) 4061 3422 Fax: (07) 4061 6555KINGAROY Phone: (07) 4162 1551 Fax: (07) 4162 5654 MACKAY Phone: (07) 4952 1399 Fax: (07) 4952 3588 MAREEBA Phone: (07) 4092 2333 Fax: (07) 4092 2992 MARYBOROUGH Phone: (07) 4122 2877 Fax: (07) 4123 1582 MILES Phone: (07) 4627 1488 Fax: (07) 4627 1204 MILLMERRANPhone: (07) 4695 1299 Fax: (07) 4695 1601MT ISA Phone: (07) 4743 3264 Fax: (07) 4743 0487 MUNDUBBERAPhone: (07) 4165 4366 Fax: (07) 4165 4881MURGON Phone: (07) 4168 1411 Fax: (07) 4168 1029 NAMBOURPhone: (07) 5476 1166 Fax: (07) 5476 1026NOOSAVILLEPhone: (07) 5442 4044 Fax: (07) 5449 9883 ROCKHAMPTON Phone: (07) 4927 2033 Fax: (07) 4922 1190 ROMA Phone: (07) 4622 1722 Fax: (07) 4622 2639 SARINAPhone: (07) 4956 1121 Fax: (07) 4959 2642SOUTHPORT Phone: (07) 5532 4888 Fax: (07) 5532 5078 ST GEORGE Phone: (07) 4625 5755 Fax: (07) 4625 3751 TINGALPA Phone: (07) 3390 7099 Fax: (07) 3390 8615TOOWOOMBA Phone: (07) 4634 4133 Fax: (07) 4634 4329TOOWOOMBAPhone: (07) 4634 3911 Fax: (07) 4634 2598
TOWNSVILLE Phone: (07) 4779 0500 Fax: (07) 4775 3758WACOL Phone: (07) 3271 3444 Fax: (07) 3271 3783WARWICKPhone: (07) 4661 2699 Fax: (07) 4661 5562YATALA NORTH Phone: (07) 3807 4971 Fax: (07) 3807 5847YATALAPhone: (07) 3807 1100 Fax: (07) 3807 2985
TASMANIA
HOBART (DERWENT PARK) Phone: (03) 6272 4344 Fax: (03) 6272 4987 BURNIE Phone: (03) 6431 5044 Fax: (03) 6431 7226DELORAINE Phone: (03) 6362 2986 Fax: (03) 6362 3453LAUNCESTONPhone: (03) 6334 0900 Fax: (03) 6334 6810
WESTERN AUSTRALIA
PERTH (WELSHPOOL) Phone: (08) 9251 4444 Fax: (08) 9251 4445 O’CONNOR Phone: (08) 9337 3000 Fax: (08) 9331 2179 OSBORNE PARK Phone: (08) 9445 1811 Fax: (08) 9445 3130 GERALDTON Phone: (08) 9965 2275 Fax: (08) 9965 2276MANDURAH Phone: (08) 9583 3525 Fax: (08) 9583 3571 MERREDIN Phone: (08) 9041 1777 Fax: (08) 9041 2570NARROGIN Phone: (08) 9881 4504 Fax: (08) 9881 4507
SOUTH AUSTRALIA
ADELAIDE (WINGFIELD) Phone: (08) 8344 0800 Fax: (08) 8349 8480 BALAKLAVAPhone: (08) 8862 2158 Fax: (08) 8862 1573BORDERTOWNPhone: (08) 8752 0633 Fax: (08) 8752 0103CLEVE Phone: (08) 8628 2150 Fax: (08) 8628 2537 COOBER PEDY Phone: (08) 8672 5830 Fax: (08) 8672 5830 KADINA Phone: (08) 8821 3922 Fax: (08) 8821 2820 KIMBAPhone: (08) 8627 2071 Fax: (08) 8680 2391LONSDALE Phone: (08) 8326 5459 Fax: (08) 8326 7939 MILLICENT Phone: (08) 8733 3555 Fax: (08) 8733 3554 MT GAMBIER Phone: (08) 8724 4500 Fax: (08) 8423 0175 PENOLAPhone: (08) 8737 3388 Fax: (08) 8737 3399ROSEWORTHY Phone: (08) 8524 8131 Fax: (08) 8524 8218 SADDLEWORTH Phone: (08) 8848 4292 Fax: (08) 8848 4151 TINTINARAPhone: (08) 8757 2077 Fax: (08) 8757 2016WOODSIDEPhone: (08) 8389 7782 Fax: (08) 8389 9084WUDINNA Phone: (08) 8680 2236 Fax: (08) 8680 2391
TAMWORTH Phone: (02) 6765 4822 Fax: (02) 6765 6648 TEMORAPhone: (02) 6977 4585 Fax: (02) 6977 4584TOTTENHAMPhone: (02) 6892 4078 Fax: (02) 6847 3277TUMUTPhone: (02) 6947 2291 Fax: (02) 6947 2291WAGGA WAGGA Phone: (02) 6925 3711 Fax: (02) 6925 2613 WALGETT Phone: (02) 6828 1500 Fax: (02) 6828 1395 WARRENPhone: (02) 6847 3422 Fax: (02) 6847 3277WAUCHOPEPhone: (02) 6585 3100 Fax: (02) 6585 3777WEE WAA Phone: (02) 6795 0320 Fax: (02) 6795 4358 WEST WYALONGPhone: (02) 6972 2595 Fax: (02) 6972 2937WOLLONGONG Phone: (02) 4231 8500 Fax: (02) 4231 8599 YOUNG Phone: (02) 6382 3999 Fax: (02) 6382 4675
VICTORIA
MELBOURNE (CLAYTON) Phone: (03) 9560 3222 Fax: (03) 9562 0396 BALLARATPhone: (03) 5337 6001 Fax: (03) 5337 6015BENALLA Phone: (03) 5762 3633 Fax: (03) 5762 3938 BENDIGO Phone: (03) 5446 8722 Fax: (03) 5446 1496 COLACPhone: (03) 5231 4300 Fax: (03) 5231 4322DANDENONG Phone: (03) 9794 5624 Fax: (03) 9794 5636 DENILIQUINPhone: (03) 5881 1355 Fax: (03) 5881 4338 ECHUCA Phone: (03) 5482 3764 Fax: (03) 5482 4439 FINLEYPhone: (03) 5883 3044 Fax: (03) 5883 3030FRANKSTON Phone: (03) 9776 9733 Fax: (03) 9776 9788 GEELONG Phone: (03) 5272 2951 Fax: (03) 5272 3245 KERANG Phone: (03) 5452 1502 Fax: (03) 5452 2994 MILDURA Phone: (03) 5022 1177 Fax: (03) 5021 1052 MORWELL Phone: (03) 5134 3633 Fax: (03) 5133 9254 NHILL Phone: (03) 5391 3267 Fax: (03) 5391 3271 PORTLAND Phone: (03) 5523 1266 Fax: (03) 5523 4533 SALE Phone: (03) 5144 5633 Fax: (03) 5144 6004 SHEPPARTON Phone: (03) 5821 4911 Fax: (03) 5821 4858 SOMERTON Phone: (03) 9308 7000 Fax: (03) 9308 7333SUNSHINE Phone: (03) 9311 4138 Fax: (03) 9310 2177 SWAN HILL Phone: (03) 5032 9444 Fax: (03) 5033 1143 WARRNAMBOOL Phone: (03) 5562 1633 Fax: (03) 5562 4802 WODONGA Phone: (02) 6024 3722 Fax: (02) 6056 1863
C-WIR-5
ALSO AVAILABLE:
QM BLUE BRUTE BEARINGS
top related