topology “the topology is the geometric representation of the relationship of the links and...

Topology

“The Topology is the geometric representation of the relationship of the links and linking devices”

OR

“Topology defines physical or logical arrangement of links in a

Network”

Categories of Topology

Topology

Mesh Star Tree Bus Ring

Mesh Topology

Mesh

Every device has dedicated a point-to-point link to every other device

Dedicated: Means that the link carries traffic only between these two devices

Links to connect ‘n’ devices Each device must have I/O

Ports

Links and Ports in Mesh Topology

Number of Links required to connect ‘n’ devices: n(n-1)/2

Number of I/O Ports: n-1

Links and Ports in Mesh Topology

In figure above, we have 5 Nodes, therefore:–No. of Links= 5(5-1)/2 = 10

–No. of I/O Ports= 5-1 = 4

Advantages of Mesh Topology

 Use of Dedicated links guarantees that each connection can carry its own load. This eliminates Traffic Problems as in case of Shared Link

Mesh Topology is robust. If one link fails, it does not effect other links

Security & Privacy due to dedicated links Point – to –Point links make Fault

Identification easy

Disadvantages of Mesh Topology

Amount of Cabling Makes Installation & Reconfiguration

difficult Sheer bulk of wiring can be greater than

the available space Number of I/O Ports Required Hardware required to connect each link

can be prohibitively expensive Therefore, Mesh topology has limited use

Star Topology

Star

Each device has a dedicated point-to-point link to a central controller ( Hub)

Devices are not directly connected to each other

Controller (Hub) acts as an exchange If one device wants to send data to the

other, it sends the data to the controller , which then relays it to the other connected device

Advantages of Star Topology

Less CablingLess Expensive than Mesh as

each device need sonly one link and one I./O Port

Easy to Install and ReconfigureRobust, if a link fails , only that

link failsEasy Fault Detection

Disadvantages of Star Topology

 Although Cabling required is far less than Mesh

Still each node must be connected to a Hub , so Cabling is still much more than some other Topologies

Tree Topology

Tree

A variation of Star TopologyNodes in a Tree are linked to a

central hub that controls the traffic to and from network

Difference b/w star and tree is not all the devices plug directly into the central HUB

Majority connects to secondary hub that is connected to central hub

Central hub & secondary hub Central Hub in a Tree is an ACTIVE HUB ACTIVE HUB contains a repeater Repeater is a hardware device that

regenerates the received bit pattern before sending them out.

Repeater strengthens TX. And increases the distance a signal can travel

 Secondary Hub in a Tree may be Active or Passive HUB

Passive Hub simply provides physical connection between attached devices

Advantages of Tree Topology

 Because of Secondary Hub, More devices can be attached to a Central Hub and therefore increase the distance a signal can travel

Enables Differentiated Services: Allows to prioritize communication, e.g. computers attached to one secondary hub can be given priority over others

Therefore, TIME SENSITIVE data will not have to wait for access to the network– Example Tree Topology: Cable TV

Bus Topology

Drop Lines and Taps

Drop Line is the connection between device and the main cable (Backbone)– Tap is a connector that;

Splices into the main cable or Punctures the sheathing of a cable to

create connection with the metallic core  Signal degrades as it travels, therefore

there is a limit on:– The number of Taps a Bus can support – The distance between those Taps

Advantages of BUS TOPOLOGY

 Easy to installBackbone can be laid on the most

efficient path and then rest of the nodes can be connected using Drop Lines

Less cabling than Mesh , Star or Tree

Difference b/w Star Cabling and Bus Cabling

Disadvantages of BUS Topology

 Difficult Reconfiguration– Difficult to add new devices– adding new devices may require

modification of backbone  No Fault Isolation

– A fault or break in backbone can disable communication even on the same side of the problem

– Damaged area reflects signals back in the direction of origin creating Noise

Ring Topology

Ring

Each device has point-to-point dedicated link with only two devices on either side

A signal is passed in the ring in one direction from device to device until it reaches its destination

Each device has a repeater incorporated When a device receives a signal destined

for another device, it regenerates the bits and pass them along

Advantages of Ring Topology

 Easy to Install and Reconfigure– Only two connections to be moved to

add or delete a device  SIMPLE Fault Isolation

– Generally a signal is circulating at all times in a ring.

– If one device does not receive a signal within a specified period, it can issue an alarm to tell network operator about the problem and its location

Disadvantages of Ring Topology

 Unidirectional Traffic A break in a ring I.e. a disabled

station can disable the entire network

 Can be solved by using:•Dual Ring or

Hybrid Toplogy

Hybrid topology

Several topologies combined in a larger topology

 Example: One department of a business may have decided to use a Bus while other has a Ring

The two can be connected via a Central Controller in Star Topology

1.27

1-3 THE INTERNET

The Internet has revolutionized many aspects of our daily lives. It has affected the way we do business as well as the way we spend our leisure time. The Internet is a communication system that has brought a wealth of information to our fingertips and organized it for our use.

1.28

Figure 1.13 Hierarchical organization of the Internet