topographic maps. what is a topographic map? a map is a representation of the earth, or part of it....

Topographic Maps

What is a Topographic Map?A map is a representation of the Earth, or part of it. The

distinctive characteristic of a topographic map is that the shape of the Earth's surface is shown by contour lines. Contours are imaginary lines that join points of equal elevation on the surface of the land above or below a reference surface, such as mean sea level. Contours make it possible to measure the height of mountains, depths of the ocean bottom, and steepness of slopes.

Index Contours1. Generally, every

fifth contour is printed darker. These lines are called index contours.

contour interval (CI)1. The vertical spacing

(difference in elevation) between contour lines is known as the contour interval. Typical contour intervals are 10, 20, 50, and 100 feet. The contour interval is generally given in the legend of the map.

Benchmarks (BM)Points on the map marked "BM" are bench marks - survey points of known elevation. The exact elevation of a point is given as "BM 60" (for an elevation 60 feet above sea level).

Tips for understanding contour lines.

There are a few rules that topographic contours must obey, however, and once you understand these rules the map becomes an extremely useful and easy to use tool.

As a result of this every contour line must eventually close on itself to form an irregular circle Contour lines on the edge of a map do not appear to close on themselves because they run into the edge of the map, but if you got the adjacent map you would find that, eventually, the contour will close on itself.

1) Every point on a contour line represents the exact same elevation

2) Contour lines can never cross one another.

Each line represents a separate elevation, and you can’t have two different elevations at the same point. The only exception to this rule is if you have an overhanging cliff or cave

3) Moving from one contour line to another always indicates a change in elevation. To determine if it is a positive (uphill) or negative (downhill) change you must look at the index contours on either side (see figure).

4) On a hill with a consistent slope, there are always four intermediate

contours for every index contour.

If there are more than four index contours it means that there has been a change of slope and one or more contour line has been duplicated. This is most common when going over the top of a hill or across a valley (see figure).

5) The closer contour lines are to one another, the steeper the slope is in the real world. The farther apart, the more gentle.

Hachure marks indicate a depression

7) Contour lines crossing a stream valley will form a "V" shape pointing in the uphill

(and upstream) direction.

Now you draw the linesImagine you have gone out and taken the elevation of several pointsNow you want to add the contour lines

Determine the contour interval and what lines you need to drawExtrapolate where the lines would be

This means thinking of an imaginary number line

Decide which contour line would fit between two points

http://terraserver-usa.com/image.aspx?T=1&S=11&Z=14&X=1701&Y=10309&W=1&qs=300+Viking+Blvd%7cWinfield%7c%7c&Addr=300+N+Viking+Blvd%2c+Winfield%2c+KS+67156&ALon=-96.9692407&ALat=37.2437477

Practice on line

3-d Topographic practice

Topographic profile

Gives you a side view

Topographic ProfileLay a strip of paper across the mapDraw a line at the start and stop of the mapDraw a tic where a contour line touches the paper Mark the elevation on the paper

Beginning with your starting elevation, go directly above the tic mark on your paper and make a small dot on the graph paper at the corresponding elevation

Draw a smooth line to connect the dots on the profileThis is what the land would look like if you were sailing up to it on a boat

Find the

HillSteep slopeCliffClosed contourStream v-upstreamIndex contoursContour interval

How would you draw this horn?

Online Topo Map Quiz