(t-link8 topp pro v1.0) · ch1 ch2 ch3 ch4 ch5 ch6 splitter/mixer t-link8 t-link8. t-link8 13...
Post on 01-Oct-2020
3 Views
Preview:
TRANSCRIPT
T-link8
CH6CH5CH4CH3CH2CH1
SPLITTER/MIXER
T-link8
T-link8
T-link8
13
T-link8
13
T-link8
CONTROL ELEMENTS
APPLICATIONS
INSTALLATION & CONNECTIONS
BLOCK DIAGRAM
TECHNICAL SPECIFICATINS8.
12
12
12
T-link8
AUDIO
INPUTS
Connectors XLR and 1/4" TRS
Type RF filtered, servo-balanced input
Impedance 50 kOhms balanced, 25 kOhms unbalanced
Nominal operating level -10 dBV to +4 dBu
Max. input level +21 dBu balanced and unbalanced
CMRR Typ. 40 dB, > 55 dB @ 1 kHz
AUDIO
OUTPUTS
Connectors XLR and 1/4" TRS
Type Electronically servo-balanced output stage
Impedance 60 Ohms balanced, 30 Ohms unbalanced
Max. output level +22 dBu balanced and unbalanced
SYSTEM
SPECIFICATIONS
Frequency response
S/N ratio
THD
5 Hz to 200 kHz, +/- 3 dBu
>95 dBu, unweighted, 22 Hz to 22 kHz
0.002 % typ. @ +4 dBu, 1kHz, gain 1
FUNCTION
CONTROLS
Main input level
Main output level
Level
Balance/pan
variable
variable
variable for each channel
placing in the stereo field
FUNCTION
SWITCHES
Main Link
Split/mix
links the main input signal to the main output
changeover from split to mix mode for each channel
INDICATORS
Input level (main)
Output level (main)
Input/output level
6-digit LED display: -18/-12/-6/0/+12/Clip
6-digit LED display: -18/-12/-6/0/+12/Clip
6-digit LED display: -18/-12/-6/0/+12/Clip
POWER
SUPPLY
Mains Voltages U.K./Australia
Europe
USA/Canada 120V ~, 60 Hz
240V ~, 50 Hz
230V ~, 50 Hz
Power Consumption max. 15 Watts
Fuse 100 - 120 V ~: T 500 mA H
220 - 240 V ~: T 315 mA H
Mains Connection Standard IEC receptacle
PHYSICAL
Dimensions (H*W*D) 483(W) 195(D) 44(H)mm (19" 7.54" 1.7")
Net Weight 2.6 kg(5.73lb)
Shipping Weight 3.5 kg
Technical Specifications
NOTAS9. 13
11
Thank you for choosing .TOPP PRO T-LINK8 is the good solutions for many problems of the
large scale sound reinforcement systems and PA applications, and it can be used as a splitter or a
mixer. For splitter application, just apply the main signal input from the MAIN IN sockets, and
select the SPLITTER mode for each individual channel, then six mono outputs can be gotten. By
For mixer application, select the MIXER mode for individual channel, and feed the input signal from
the mono input, then six input signals can be mixed together, and output from the MAIN OUT. By
Please reserve your time to read this manual before running the unit, and you will be the real master
Features:
The splitter/mixer is equipped with following features:T-LINK8
1 rack size.
SPLIT / MIX switch for each mono channel.
2 input, 6+2 outputs splitter.
8 Balance / Pan control for each channel.
Main input and output level control.
MAIN LINK function allows to route the MAIN IN signal to MAIN OUT, vice versa.
Level meters for each stage.
XLR balanced connectors for 4 mono channels, and TRS type for another 2 mono channels.
Dual voltage unit for global operation.
of your T-LINK8.
depressing the MAIN MIX button, two further outputs can be provided.
4
T-link8
11
T-link8
1 2 3 4
4321
2
1
3
4 2
1
3
4
2
1
3
2
1
3
2
1
3
4 2
1
3
4
2
1
3
2
1
3
2
1
3
4 2
1
3
4
2
1
3
2
1
3
BALANCE
BALANCE
BALANCE
PAN
PAN
PAN
SPLIT/MIX
SPLIT/MIX
SPLIT/MIX
SPLIT/MIX
SPLIT/MIX
SPLIT/MIX
LEVEL
LEVEL
LEVEL
CH1
CH2
CH3
CH1
CH2
CH3
2
1
3
4
2
1
3
42
1
3
LINKMAIN_LEFT MAIN_LEFT
2
1
3
42
1
3
2
1
3
4
MAIN_RIGHT MAIN_RIGHT
2
1
3
4 2
1
3
4
2
1
3
2
1
3
2
1
3
4 2
1
3
4
2
1
3
2
1
3
2
1
3
4 2
1
3
4
2
1
3
2
1
3
BALANCE
BALANCE
BALANCE
PAN
PAN
PAN
SPLIT/MIX
SPLIT/MIX
SPLIT/MIX
SPLIT/MIX
SPLIT/MIX
SPLIT/MIX
LEVEL
LEVEL
LEVEL
CH4
CH5
CH6
CH4
CH5
CH6
F
E
D
C
B
A
F
E
D
C
B
A
Block Diagram
depressing the MAIN MIX button, two further inputs can be provided.
1. MAIN INPUT LEVEL control
This knob is used to adjust the level of the main input signal, and its adjustable range goes from
- to +10dB.
2. INPUT LEVEL meter
This 6-digit meter tells you the level of the main input signal. While the Clip LED lights up,
please turn down the main input signal, otherwise, the system will be distorted.
3. MAIN LINK control
Use this switch to link the MAIN IN with the MAIN OUT.
4. MAIN OUTPUT LEVEL control
This knob is used to adjust the level of the main output signal, and its adjustable range goes from
- to +10dB.
5. OUTPUT LEVEL meter
This 6-digit meter tells you the level of the main output signal. While the Clip LED lights up,
please turn down the main signal at either each input stage or the main output stage, otherwise,
the system will be distorted.
6. SPLIT / MIX
Use this switch to select the specific operational mode for each individual mono channel.
For SPLITTER mode, please let the switch released, and the main input signal can then be split
into each mono channel output.
For MIXER mode, please engage this switch, and now, the mono channel input signal will be sent
to the main output bus, combined with the main input signal on condition that the MAIN LINK
is activated, you can get the mixed signal output from the MAIN OUT sockets.
Further, also for the MIXER mode, you can route the mono channel input signal to the mono
channel output directly.
7. LEVEL control for each channel
This knob is used to adjust the level of each mono channel, and its adjustable range goes from
- to +10dB,definitely, In SPLITTER mode, this control is used to determine the output level
of each individual mono channel. While in MIXER mode, this control can be used to determine
how much the mono channel input signal is sent the main output bus and/or each individual
mono channel output.
to
1
2
3 4
5
67
8
9 10
CH6CH5CH4CH3CH2CH1
5
T-link8
8. INPUT / OUTPUT LEVEL meter
This 6-digit meter tells you the output level of each mono channel, while the Clip LED lights up,
please turn down the level control, otherwise, this channel will be distorted.
10
T-link8
b. In Line Connection
Rack ountingM
The most secure mounting is on a universal rack shelf available from various rack manufactures or
your music dealer. The T-LINK8 fits into one standard 19" rack unit of space. Please allow at least an
additional 4" depth for the connectors on the rear panel. Be sure that there is enough air space
around the unit for sufficient ventilation and please do not place the T-LINK8 on high temperature
devices such as power amplifiers etc. to avoidoverheating.
For these applications, the T-LINK8 provides XLR connectors and 1/4" TRS phone jack to easily interface
with most professional audio devices. Follow the configuration examples below for your particular
connection.
Unbalanced
Balanced
Tip
Ring
Sleeve
Tip
Ring
Sleeve
Tip
Ring
Sleeve
1
2
3
1
2
3
1
2
3
TIP RING SLEEVESLEEVE RING TIP
TIP RING SLEEVE
21
3
12
3
12
3
Tip
Ring
Sleeve
Tip
Ring
Sleeve
Tip
Sleeve
Tip
Sleeve
Tip
Sleeve
Cent er
Cent er
Centre
Screen
Screen
Screen
1
2
3
Tip
Ring
Sleeve
1
2
3
1
2
3
TIP SLEEVE
TIP SLEEVE
TIP RING SLEEVE
TIP RING SLEEVE
12
3
21
3
21
3
Tip
Ring
Sleeve
1
2
3
Tip
Sleeve
1
2
3
TIP RING SLEEVE
TIP SLEEVE
12
3
12
3
SLEEVE TIP
SLEEVE RING TIP
9. BALANCE / PAN control
Generally, the main section uses the stereo input and output, while, for each individual channel, mono
application is configured. So, if the stereo main signal is split into the mono channel output, or the mono
input signal is routed to the stereo main output bus, please use this knob to determine the proportion
between the left and the right.
10. POWER SWITCH & POWER LED
This switch turns on/off the unit. When the unit is powered on, the LED will light up.
11. FUSE HOLDER
Before you attempt to connect and operate the unit, please make sure that your local voltage matches
the voltage on the fuse-holder cover.
a
qualified blow
after replacing,
Caution: The fuse protecting the AC supplies circuits of this unit. The fuse can only be changed by
technician, in the event of a fault or changing the supply voltage. If the fuse continues to
discontinue use of this unit before repaired.
12. AC inlet
This connector is meant for the connection of the supplied main cord. Do not insert power cable
into the unit until the voltage has been correctly set. Do not plug power cable into AC power until
voltage has been correctly set.
13. MAIN INPUTS
These two XLR balanced connectors are used to input the main stereo signal. In SPLITTER mode, it can
be split into each mono channel output.
11 12 13141516
6
T-link8
14. MAIN OUTPUTS
These two XLR balanced connectors are used to output the main stereo signal. By depressing the
MAIN LINK, It can be linked with the MAIN IN directly.
15. INPUT for the mono channel
For Channel 1~4, use the XLR balanced connectors to input the mono signal, while, for Channel
5~6, please use the TRS type.
16. OUTPUT for the mono channel
For Channel 1~4, use the XLR balanced connectors to output the mono signal, while, for Channel
5~6, please use the TRS type.
9
T-link8
This is a dual voltage unit. Please ensure that the T-LINK8
Do not insert power cord into the unit until voltage has been correctly set. Do
The mains connection of the T is made by using the
is set to the correct supply voltage
before plugging the power cord into the wall outlet, use the same fuse as marked on the fuse
holder at the AC power connection socket.
not plug the
power cord into AC power until voltage has been correctly set.
-LINK8 enclosed mains cord and a standard
IEC receptacle. It meets all of the international safety certification requirements.
Either the 1/4" TRS (Tip-Ring-Sleeve) phone jack or the XLR servo connector can be wired in
balanced and unbalanced modes, which will be determined by the actual application status, Please
wire your systems as the following examples:
The T-LINK8 presents with balanced XLR connectors and 1/4" TRS phone jack, it can be interfaced
by several ways to support a variety of applications without any signal loss.
TRS Type Unbalanced
TipRing
Sleeve
+
Mains Connection
Audio onnectionC
a. Wiring Configuration
For 1/4" Phone jack
TS Type Unbalanced TRS Type Balanced
TipRing
Sleeve
+-
Sleeve
Tip
+
For XLR connector
XLR Type Unbalanced XLR Type alancedB
Pin3 (-)
Pin2 (+)
Pin1 ( )
(Linked to Pin1 manually, )
Pin1 ( )
Pin2 (+)Pin3 (-)
From the panel introduction on the chapter 3, you must have caught a clear answer to " What is it?" in
your mind as to our T-LINK8, SPLITTER / MIXER, hereafter, we will show you the further explanation
on "How to use it?", So that, you can be the real master of this unit.
How to use T as the splitter-LINK8
Sometimes, in the large scale PA / sound reinforcement systems, you may be disturbed by this kind
of problems: one pre-send signal needs to be monitored by several groups, or the main mix output
of the console should be transited to several power amplifiers, etc.
to 6 outputs. With the MAIN LINK button depressed, 2 further outputs are added.
And now, with your T-LINK8,
you will get the best solution.
Connect the T-LINK8 into your systems as the demonstrated, you can split a specific main input signal
into up
Two further
outputs
Output 1Output 2Output 3Output 4Output 5Output 6 Main input
signal
T-link8
In this application, use the SPLIT/MIX switch to select the SPLITTER operational mode for each mono
channel, apply the main signal from the MAIN IN sockets, and get the 6 outputs from the mono
OUTPUT sockets of each channel. While the MAIN LINK is engaged, the MAIN OUT will also be
linked with the MAIN IN signal, and two further outputs are provided.
This application is widely used for the mixing of one group main stereo signal with several mono signals.
How to use T-LINK8 as the mixer
In this application, use the SPLIT/MIX switch to select the MIXER operational mode for each mono
channel, input the signal from the mono INPUT of each channel, and output the main mixed signal from
the MAIN OUT sockets. While the MAIN LINK is engaged, the MAIN IN will also be linked with the
MAIN OUT signal, and two further input signals can be mixed with the main output signal.
Input 6 Main mixed
signal output
Input 1Input 2Input 3Input 4Input 5 Two further
iutputs
8
T-link8
7
PO
WER
PO
WER
ALL
OU
TP
UT
P.L
ZO
NE
PA
GIN
GS
ELEC
TO
RZ
ON
EPA
GIN
GS
ELEC
TO
R
010
010
010
010
010
ZO
NE
1Z
ON
E1
ZO
NE
2Z
ON
E2
ZO
NE
3Z
ON
E3
ZO
NE
4Z
ON
E4
11
11
22
22
33
33
44
44
55
55
66
66
MPA
-12
0R
S-E
CH
OM
PA
-12
0R
S-E
CH
OP.A
.A
MP
LIF
IER
P.A
.A
MP
LIF
IER
10
0
MA
ST
ER
MA
ST
ER
-10
-10
+10
+10
-10
-10
+10
+10
AU
XA
UX
INP
UT
1IN
PU
T1
MA
ST
ER
MA
ST
ER
REC
.
INP
UT
REC
.
INP
UT
SD
/MM
C/
VO
L+
VO
L+
VO
L-
VO
L-
SD
/ US
BS
D/U
SB
RP
TR
PT
Dig
italM
p3
Pla
yer
Record
ing
+D
igitalM
p3
Pla
yer
Record
ing
+
LE
VE
L
RE
C
PE
AK
TR
EB
LE
BA
SS
EC
HO
AU
XIN
PU
T3
INP
UT
3IN
PU
T2
INP
UT
2IN
PU
T1
INP
UT
1M
P3
USB
Gu
ita
rSte
reo
Ke
yb
oa
rdC
om
pu
ter
De
skto
pPa
gin
g
Mic
rop
ho
ne
Wire
less
Tie
Clip
Wire
less
Ha
nd
he
ldM
ICD
VD
Pla
ye
r
top related