supremadm v1.01
Post on 27-Oct-2015
167 Views
Preview:
TRANSCRIPT
Suprema DM Guide Version 1.00
1
Note: See h.p://www.entrypass.net/ for updates, revisions, and download the latest installa<on manual There are currently 2 version of EntryPass PlaCorm1 Access Control System available for different card number system 1) EntryPass PlaCorm1 Access Control System (6 Digit Card Number System) cater for 6 digit card number installa<on 2)EntryPass PlaCorm1 Access Control System (10 Digit Card Number System) cater for 10 digit card number installa<on For EntryPass PlaCorm1 Access Control System to work correctly, both control panel and soPware MUST be using the same card number system This soPware installa<on manual might be updated without prior no<ce Please refer to separate EntryPass PlaCorm1 User Manual for detail opera<on help. The Official EntryPass PlaCorm1 User Manual can be downloaded from our website under “Download” sec<on
2
Technical Support If you cannot find the answer to your ques<on in this manual or in the Help files, we recommend you contact your system installer. Your installer is familiar with your system configura<on and should be able to answer any of your ques<ons. Should you need addi<onal informa<on, please call our Technical Support Help desk, Monday to Friday 9:00 AM to 6:00 PM (GMT +8:00) Method Details Phone + 60 (3) -‐ 8068 1929 Fax + 60 (3) -‐ 8068 1922 Internet www.entrypass.net Email support@entrypass.net
BEFORE YOU BEGIN
3
4
Serial Control Panel Ac<ve Network Control Panel
BioLite Net BioEntry Plus
EP.S3200
EP.S3400
EP.N5100
EP.N5200
EP.N5400
Suprema Biometrics Devices (SBD)
Entrypass HCB based control panels that works with Suprema BioLite Net & BioEntry Plus
5
IMPORTANT NOTICE
Before any SBD devices can be integrated to Entrypass HCB based control panels, certain parameters must be configured. Please follow the workflow below for detailed guidelines.
6
Configure IP Address for Suprema Biometrics
Devices (SBD)
Connect SBD to PC which have Suprema DM installed using a
cross-‐cable
Step -‐ 01 Step -‐ 02
Connect to SBD and retrieve the Device ID
Load parameters to SBD for it to work with
Entrypass
Set SBD DIP Switch to OFF Posi<on
Connect SBD to Entrypass HCB based
control panel
Step -‐ 03
Power off SBD
Step -‐ 04 Step -‐ 05 Step -‐ 06
Step -‐ 07 Step -‐ 08 Step -‐ 09
Step -‐ 10 Step -‐ 11 Step -‐ 12
Standard Entrypass – Suprema Biometrics Integra<on Workflow
7
To configure the Suprema BioLite Net device or BioEntry Plus device, you have to prepare the following items: (i) Suprema DM program (Located in the EntryPass PlaCorm1 CD) (ii) Ethernet Connector (come with any Suprema device) (iii) Cross cable (Cat 5e) (iv) PC or notebook (v) MIFARE Writer (Purchase Separately) (vi) Suprema BioMini Enrollment Sta<on (Purchase Separately) (vii) Entrypass HCB based control panels
(i) EP.S3200 (ii) EP.S3400 (iii) EP.N5100 (iv) EP.N5200 (v) EP.N5400
Tools Required
8
Each SBD must be configured with a valid IP address before it can communicate with Suprema DM To configure an IP address for Suprema BioLite Net device, please refer to BioLite Net User Guide, page 46 (except Server senng select ‘No Use’). To configure an IP address for Suprema BioEntry Plus device, please refer to BioEntry Plus InstallaLon, page 26.
Step-‐01 : Configure SBD IP Address
9
Step-‐02 : Connec<ng SBD to PC / Notebook
PC / Notebook with Suprema DM
Cross Cable
BioLite Net
Note for BioEntry Plus user Dipswitch 2 must be turn “On” to allow modifica<on on the parameter
10
Launch Suprema DM
Select TCP/IP
11
Enter SBD IP Address
Default Port No.
Click “Connect”
1
2
12
Click “Get”
Connected to SBD
Copy down the Device ID
4
13
Note for BioEntry Plus user Dipswitch 2 must be turn “ON” before loading parameters, please refer BioEntry Plus User Guide Page-‐26
Select SBD Output format
5
Click “Load”
6
14
Successfully loaded the parameters to SBD
15
Switch off all power source to SBD
BioLite Net
BioEntry Plus
Note for BioEntry Plus user Dipswitch 2 must be turn “OFF” aPer power source is disconnected to prevent losing parameters aPer power cycle
Successfully loaded the parameters to SBD
16
BioLite Net
BioEntry Plus
Connec<ng SBD to Entrypass HCB Control Panel
Please refer HCB Wiring Guide
Please refer HCB Wiring Guide
17
Entrypass PlaCorm1 Access Control System
Finger Only
Finger + Card
Card + Pin
Card Only
18
Add control panel to Entrypass PlaCorm1 ACS
Select “Reader Type” for Suprema
Step -‐ 01 Step -‐ 02
Enable Suprema Device ID
Enroll Administrator’s fingerprint template
Step -‐ 03
Enroll Staff’s fingerprint template
Step -‐ 04 Step -‐ 05 Step -‐ 06
Entrypass PlaCorm1 Access Control System – Suprema SBD Integra<on Workflow
Connect Suprema BioMiNi Enrollment Sta<on to EP.P1
Pre-‐Requisites
SBD are connected to HCB based control panel
Suprema BioMiNi Enrollment StaLon Please refer to individual user manual to setup
USB
19
Select “Suprema” from “Reader Type” dropdown box
Select “Reader” tab
1
2
Entrypass PlaCorm1 Access Control System – Add Control Panel
20
Check “User Fingerprint” checkbox and enter the SBD Device ID you obtained previously
Select “Reader” tab
3
4 Click “Save and Close” to complete the setup
5
Entrypass PlaCorm1 Access Control System – Add Control Panel
21
In “Preferences”, select “Suprema” tab
1
Entrypass PlaCorm1 Access Control System – Enroll administrator fingerprint
Click “Enroll” 2
22
Once captured, click “Accept”
Place finger on top of BioMiNi
1
2
Entrypass PlaCorm1 Access Control System – Enroll administrator fingerprint
23
If successful, “Template 01” will be
enabled
Click “Accept” to complete the process
To enroll user to “Finger Only” Mode
Go “Control Panel” > “Company” > “View Staff”
25
Entrypass PlaCorm1 Access Control System – Enroll staff fingerprint
In “View Staff”, click “Add”
26
Entrypass PlaCorm1 Access Control System – Enroll staff fingerprint
Select “Card Data” tab 2
Enter all necessary informa<on in “Personal Data” tab
1
27
Entrypass PlaCorm1 Access Control System – Enroll staff fingerprint
Click “Add”
3
28
If you know the card number, enter it here
Entrypass PlaCorm1 Access Control System – Enroll staff fingerprint
4 Else, scan the card number using the MIFARE writer
5
Click “Add and Close” to complete the process 6
29
Finger Only Mode
Click “Enroll”
Select from dropdown menu “Finger Only” mode
8
9
Select “Fingerprint” tab
7
30
Finger Only Mode
Once captured, click “Accept”
Place finger on top of BioMiNi
10
11
Model: EP.S2100
If successful, “Template 01” will be
enabled
Finger Only Mode
Click “Accept” to complete the process
12
To enroll user to “Card + Finger” Mode
Repeat Step-‐1 to Step-‐07
Card + Finger Mode
Click “Enroll”
Select from dropdown menu “Card + Finger” mode
8
9
Once captured, click “Accept”
Place finger on top of BioMiNi
Card + Finger Mode
10
11
If successful, “Template 01” will be
enabled
Card + Finger Mode
Click “Accept” to complete the process
12
Card + Finger Mode
Place MIFARE on top of writer
Click “Write” to start wri<ng data to card
13
14
Successfully enrolled the user fingerprint on card
To enroll user to “Card + Pin” Mode
Repeat Step-‐1 to Step-‐03
Card + Pin Mode
Enter desire Pin number
Click “Accept”
1
2
40
If you know the card number, enter it here
4 Else, scan the card number using the MIFARE writer
5
Click “Add and Close” to complete the process 7
Card + Pin Mode
Enter desire Pin number
6
Please choose ‘Card + PIN’ mode for card + PIN no., and then click ‘Enroll’ bu.on.
Card + Pin Mode
Select from dropdown menu “Card + Pin” mode
8
Click “Enroll” 9
Once captured, click “Accept”
Place finger on top of BioMiNi
Card + Pin Mode
10
11
If successful, “Template 01” will be
enabled
Click “Accept” to complete the process
Card + Pin Mode
12
Card + PIN Mode
Place MIFARE on top of writer
Click “Write” to start wri<ng data to card
13
14
Successfully enrolled the user pin on card
To enroll user to “Card Only” Mode
Repeat Step-‐1 to Step-‐07
Card Only Mode
Click “Enroll”
Select from dropdown menu “Card + Finger” mode
8
9
Once captured, click “Accept”
Place finger on top of BioMiNi
10
Card Only Mode
11
If successful, “Template 01” will be
enabled
Click “Accept” to complete the process
Card Only Mode
12
Place MIFARE on top of writer
Click “Write” to start wri<ng data to card
Card Only Mode
13
14
Successfully enrolled card only mode
Thank You
top related