spe iptc poster gas hydrate
Post on 16-Jul-2015
1.051 Views
Preview:
TRANSCRIPT
IPTC 13061
Gas Hydrate Problems in Desert of Sultanate of Oman: Experiences and Integrated Inhibition Program
Ardian Nengkoda, Abdulla Harthy, Wael Afify Taha, Hendrikus Reerink, Petroleum Development Oman, Alfred Hase, Champion Technology, Lamda Muchjin, Crescent Petroleum, Supranto, Suryo Purwono, Gadjah Mada University
Phone: +968-24670501, Fax: +968-24670632, E-mail: ardian.nengkoda@pdo.co.om
Abstract
Currently, there are more than 10 oil producing station, in both North and South area operation of Petroleum Development Oman, which facing a unique gas hydrate problems. Most of these wells are producing by the support of gas lift. Therefore, it is very important that the gas lift network is kept optimally operating to maintain the intended production. The ambient temperature in Sultanate of Oman desert drops to as low as 5°C during the coldest 3 months in winter, when hydrates form in several gas lift lines. This causes affected wells to cease production and results in unscheduled deferment. So far, the problem was partly controlled by the use of methanol as hydrate inhibitor (a proven method used worldwide to restrict gas hydrate formation), however there are resulted many issues mainly HSE associated with the use of methanol. The main objectives of this project are to look the other chemicals alternative as hydrate inhibitor – move from methanol to another cost effective and safe chemical inhibitor and the goal is to ensure that the system is adequately inhibited against hydrate formation and that inhibitor injection is optimized. The second goal is to develop a warning system should hydrate start to form (prior to hydrate build up and pipeline blockage). The paper also defines laboratory testing as mandatory requirement to test an alternative hydrate inhibitor and practical facilities up grade.
7-9 December 2009, Doha, Qatar
BAH.ZA.74PI038/AI1/PV.CV
kPag
BAH.ZA.74TI038/AI1/PV.CV
%
BAH.ZL058.THP
KPa
BAH.ZL058.CHP
KPaBAH.ZA.74FRC552/PID1/OUT.CV
%
BAH.ZA.74FRC552/PID1/PV.CV
m 3/dBAH.ZA.74FRC552/PID1/SP.CV
m 3/d
Plot-0
9/2/2009 11:19:43.772 16/2/2009 11:19:43.7727.00 days
1000
2000
3000
4000
5000
6000
7000
0
8000
0
60
200
1200
0
6000
0
100
0
40000
0
40000
15000.00
14992.78
26.38570
1920.2
334.72
41.56580
6880.992
X-58
K-7401/02/05 DISCHARGE
K-7401/2 TO GAS LIFT MANIFOLDTubing Head Pressure
Casing Head PressureFlow control to A7468 pos 4
Flow control to A7468 pos 4
Flow control to A7468 pos 4
BAH.ZA.74PI038/AI1/PV.CV
kPag
BAH.ZA.74TI038/AI1/PV.CV
%
BAH.ZL048.THP
KPa
BAH.ZL048.CHP
KpaBAH.ZA.74FRC549/PID1/OUT.CV
%
BAH.ZA.74FRC549/PID1/PV.CV
m 3/d
BAH.ZA.74FRC549/PID1/SP.CV
m 3/d
Plot-0
9/2/2009 11:13:53.939 16/2/2009 11:13:53.9397.00 days
1000
2000
3000
4000
5000
6000
7000
0
8000
0
60
0
1000
0
7000
0
100
0
50000
0
50000
25000.00
24933.71
59.46206
5029.0
672.00
41.59154
6876.543
X-48
K-7401/02/05 DISCHARGE
K-7401/2 TO GAS LIFT MANIFOLD
Tubing Head Pressure
Casing Head Pressure
Flow control to A7468 pos 1
Flow control to A7468 pos 1
Flow control to A7468 pos 1
BAH.ZA.74PI038/AI1/PV.CV
kPag
BAH.ZA.74TI038/AI1/PV.CV
%
BAH.ZL009.THP
KPa
BAH.ZL009.CHP
Kpa
BAH.ZA.74FRC546/PID1/OUT.CV
%
BAH.ZA.74FRC546/PID1/PV.CV
m 3/d
BAH.ZA.74FRC546/PID1/SP.CV
m 3/d
Plot-0
9/2/2009 11:18:12.526 16/2/2009 11:18:12.5267.00 days
1000
2000
3000
4000
5000
6000
7000
0
8000
0
60
300
750
2000
4500
0
100
0
50000
0
50000
28000.00
28564.88
59.16791
3979.0
670.00
41.56270
6883.778
X-9
K-7401/02/05 DISCHARGE
K-7401/2 TO GAS LIFT MANIFOLD
Tubing Head Pressure
Casing Head Pressure
Flow control to A7468 pos 2
Flow control to A7468 pos 2
Flow control to A7468 pos 2
BAH.ZA.74PI038/AI1/PV.CV
kPag
BAH.ZA.74TI038/AI1/PV.CV
%
BAH.ZL014.THP
KPa
BAH.ZL014.CHP
Kpa
BAH.ZA.74FRC547/PID1/OUT.CV
%
BAH.ZA.74FRC547/PID1/PV.CV
m 3/d
BAH.ZA.74FRC547/PID1/SP.CV
m 3/d
Plot-0
9/2/2009 11:17:34.464 16/2 /2009 11:17:34.4647.00 days
1000
2000
3000
4000
5000
6000
7000
0
8000
0
60
0
800
0
7000
0
100
0
50000
0
50000
25000.00
24944.66
43.84108
0.0000
0.0000
41.60728
6885.635
X-14
Moderate hydrate (1 or 2 times g/l flow stop – white line)
Worse hydrate (erratic flow of g/l-white color)
Before and after heat tracing installation
Chemical Injection
Current Operation Hydrate Envelope without Methanol and With Methanol Injection
Three Cavities in Gas Hydrates
Schematic of a hydrate autoclave
Conclusions and Project Plans
The results of the autoclave tests are presented in Figures 8 and 9, and are summarised below. Dose rates of the kinetic hydrate inhibitor and thermodynamic inhibitor are based on produced water volume scenario.
For gas compositions X Field as Table 2, two blank tests were performed each using DI water only (no KHI, Corrosion Inhibitor or a thermodynamic inhibitor). The induction time tH (which is the duration from start until the point where hydrates starts to form indicated by a pressure drop) was recorded as being approximately 2 hours.
First tests have been performed with KHI on its own to check which KHI is showing the best performance for this application. Relatively fast it was noticed that even at higher KHI dose rates the obtained induction times were relatively short, less than 12hours. Therefore it has been decided to add MEG as a thermodynamic inhibitor to reduce the sub cooling further into a region, where the KHI can protect the system longer against hydrate formation. The dose rate for the kinetic hydrate inhibitor and the thermodynamic inhibitor MEG are based on produced water.
Results obtained with 15% and 17.5% MEG (vol.%) showed no improvement in the performance of the KHI at 3.0%. The threshold level was obviously achieved when 20% MEG was added to test runs. At that MEG concentration the induction times was increased to over 40 hours at a constant dose rate of 30000ppm KHI. With 20vol.% (22.2wt.%) MEG the hydrate equilibrium temperature was dropped to 15°C at 58bar, which leads to a sub cooling of ~10°C. Due to the fact that the sub cooling has been lowered by the injection of 20% MEG, further tests have been performance in order to check whether it is possible to achieve a further reduction in the KHI dose rate. Autoclave tests at 22500ppm didn’t improve the KHI performance, but at 25000ppm the determined induction time was 59 and greater than 72hours (test was stopped) respectively.
Based on these results the optimal performance of the KHI has been achieved in lab tests at 2.5% dose rate in the presence of 20% MEG and 20ppm Corrosion Inhibitor as Figure 9. For a shorter protection time against hydrate formation less KHI might be required. A programme of laboratory tests under PDO X Fied conditions showed that:- The addition of MEG is required in order to achieve a reasonable performance of the KHI- The additional amount of MEG was 20% for the X Field gas, the percentages are based on produced water at gas lift line.- No significant impact of the Corrosion Inhibitor has been observed during the lab test and further field testing will be conducted to reflect laboratory testing- Hydrate formation is a very expensive problem faced by the oil and gas industry, which must be solved in an economically and environmentally appropriate manner.
IPTC 130617-9 December 2009, Doha, Qatar
BAH.ZA.74FRC549/PID1/SP.CV
m 3/d
BAH.ZA.74FRC549/PID1/PV.CV
m 3/d
BAH.ZA.74FRC549/PID1/OUT.CV
%
BAH.ZL048.CHP
Kpa
BAH.ZL048.THP
KPa
BAH.ZA.74PI038/AI1/PV.CV
kPag
BAH.ZA.74TI038/AI1/PV.CV
%
Plot-0
5/1/2009 09:19:00.717 12/1/2009 09:19:00.7177.00 days
10000
20000
30000
40000
0
50000
0
50000
0
100
0
7000
0
1000
0
7000
30
46
35.96710
7145.586
500.00
5209.0
69.35149
35605.26
35000.00
BAH.ZA.74FRC549/PID1/SP.CV
m 3/d
BAH.ZA.74FRC549/PID1/PV.CV
m 3/d
BAH.ZA.74FRC549/PID1/OUT.CV
%
BAH.ZL048.CHP
Kpa
BAH.ZL048.THP
KPa
BAH.ZA.74PI038/AI1/PV.CV
kPag
BAH.ZA.74TI038/AI1/PV.CV
%
Plot-0
29/12/2008 09:21:36.129 5/1/2009 09:21:36.1297.00 days
10000
20000
30000
40000
0
50000
0
50000
0
100
0
7000
0
1000
0
7000
28
44
32.32271
7054.747
389.88
3302.1
100.0000
-38914.24
24000.00
Before increase
injection rate
after increase injection rate
Increasing flow rate of gas lift through the well give slight effect to duration of hydrate formation at control valve (light blue line)
Fig. 8 Blank Test Result
Fig. 9 Result KHI Optimization
top related