simulation basics chapter two. training manual simulation basics august 26, 2005 inventory #002265...
Post on 01-Jan-2016
217 Views
Preview:
TRANSCRIPT
August 26, 2005Inventory
#0022652-2
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
Training Manual
Simulation Basics
Chapter Overview
• In this chapter, the basics of using Simulation to perform analyses will be covered, which include:– The Simulation GUI and Operation
– Introduction to the Simulation Wizard
– Basic Analysis Procedure
• The capabilities described in this section are generally applicable to the ANSYS DesignSpace Entra licenses and above, unless explicitly noted with the lower-left hand table.
ANSYS License AvailabilityDesignSpace Entra xDesignSpace xProfessional xStructural xMechanical/Multiphysics x
August 26, 2005Inventory
#0022652-3
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
Training Manual
Simulation Basics
A. Launching Simulation
• Recall that there are two ways of running Simulation:– Configured from within ANSYS Workbench …
– … or directly from a supported CAD system
Model shown is from a sample Solid Edge assembly.
August 26, 2005Inventory
#0022652-4
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
Training Manual
Simulation Basics
• The components of the user interface are shown below:
• Short descriptions of each component are covered next
… Simulation Interface
Tree Outline
Details ViewGraphics Window
Toolbars
Simulation Wizard
Menus
Workbench Tabs
August 26, 2005Inventory
#0022652-5
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
Training Manual
Simulation Basics
… GUI – Menus
• The menus provide much of the functionality present in Simulation. Covering each menu item may be tedious, so only the more commonly used menu items are covered below:– The title bar lists the currently active ANSYS license
– “File > Save” to save the .dsdb Simulation database
– “File > Clean” to delete mesh and/or results from database
– “Edit > Select All” to select all current entities in the window
– “Units” to change units on-the-fly
– “Tools > Options… ” to customize settings and options
– “Help > ANSYS Simulation Help” to invoke documentation
August 26, 2005Inventory
#0022652-6
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
Training Manual
Simulation Basics
… GUI – Toolbars
• There are four sets of toolbars to provide users quick access to functionality also found in the menus.
– The toolbars can be repositioned anywhere on the top of the Simulation window
– The “Context” toolbar, as will be illustrated later, will change, depending on what branch is active in the “Outline” tree.
– Tooltips appear if the cursor is placed over the toolbar button
– A “Unit Conversion” toolbar is also available (not shown)
Standard Toolbar
Graphics Toolbar
Named Selection Toolbar
Context Toolbar
August 26, 2005Inventory
#0022652-7
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
Training Manual
Simulation Basics
… GUI – Toolbars
• The “Standard” toolbar is shown below:
• The “Graphics” toolbar is used very often:
– The left mouse button can be either in “selection” mode or “graphics manipulation” mode. The above toolbar buttons grouped as “select entities” and “graphics manipulation” control the left-mouse button behavior.
– The selection of entities of the CAD geometry can be done either by individual selection or by box-selection. This is controlled by the “Select Mode” icon
Save .dsdb Bring up Simulation Wizard Solve ModelNew or Open .dsdb Capture Snapshot
Graphics ManipulationSelect entities Select Adjacent WireframeFit AllSelect mode Viewports
August 26, 2005Inventory
#0022652-8
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
Training Manual
Simulation Basics
… GUI – Outline Tree
• The Outline Tree provides an easy way of organizing the model, materials, mesh, loads, and results for the analysis– The “Model” branch contains the input
data required for the analysis
– The four main sections of the “Model” branch include “Geometry,” “Contact” (if present), “Mesh,” and “Environment.”
– The “Environment” branch contains the loads as well as the “Solution” branch,which holds results.
– Other branches (not covered here) are also available.
August 26, 2005Inventory
#0022652-9
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
Training Manual
Simulation Basics
… GUI – Outline Tree
• The Outline Tree shows icons for each branch, along with a status symbol. Examples of the status symbols are below:– Checkmark indicates branch is fully defined/OK
– Question mark indicates item has incomplete data (need input)
– Lightning bolt indicates solving is required
– Exclamation mark means problem exists1
– “X” means that item is suppressed (will not be solved)
– Transparent checkmark means body or part is hidden
– Green lightning bolt indicates item is currently being evaluated
– Minus sign means that mapped face meshing failed
Becoming familiar with the basic status symbols allows users to debug Simulation problems quickly.
August 26, 2005Inventory
#0022652-10
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
Training Manual
Simulation Basics
… GUI – Details View
• The Details View provides a means of inputting data. The contents will change, depending on branch selected.– White field: shows current input data
• Data in white text field is editable
– Gray (or Red) field: shows informative data• Data in gray fields cannot be modified.
– Yellow field: incomplete input data• Data in yellow fields indicates missing
information.
August 26, 2005Inventory
#0022652-11
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
Training Manual
Simulation Basics
… GUI – Graphics Window
• The Graphics Window shows the geometry and results. It can also provide worksheet (tabular) listings, the HTML report, and a Print Preview option.
Geometry Tab Worksheet Tab
Print Preview Tab Report Preview Tab
Job Status Tab
The Job Status tab provides information on jobs being solved remotely.
The remote solve capability will be discussed in the Simulation Advanced Training Course
August 26, 2005Inventory
#0022652-12
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
Training Manual
Simulation Basics
… GUI – Simulation Wizard
• The Simulation Wizard is an optional component, a useful aid to remind users steps required to complete an analysis– The Simulation Wizard provides a list of required
steps and the status of them
– Green checkmark indicates the item is complete
– Green “i” shows an informational item
– A greyed symbol shows that the step cannot beperformed yet
– A red question mark means that there is an incomplete item
– An “x” means that the item is not performed yet
– A lightning bolt means that the item is ready to besolved or updated
• The Simulation Wizard can be toggled on/off byselecting the button on the Standard Toolbar
August 26, 2005Inventory
#0022652-13
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
Training Manual
Simulation Basics
• When first attaching a model to Simulation, the Startup Panel is shown (optionally), allowing the user to select a Simulation Template.
B. Startup Panel
August 26, 2005Inventory
#0022652-14
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
Training Manual
Simulation Basics
• The benefit of the Startup Panel is that the appropriate results and Simulation Wizard will appear– “Stress Branch” is selected in the example below. Note that
results and the Stress Wizard are automatically chosen
… Startup Panel
August 26, 2005Inventory
#0022652-15
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
Training Manual
Simulation Basics
… Simulation Wizard
• By selecting an item on the “Required Steps” checklist, a callout appears, illustrating how that function is performed.– In the example below, “Verify Materials” was selected, and the
callout shows the user where this item can be changed.
August 26, 2005Inventory
#0022652-16
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
Training Manual
Simulation Basics
… Simulation Wizard
• The Simulation Wizard is handy for users who do not use Simulation every day– Besides basic functionality, callouts
for more advanced items are also available as shown on right
August 26, 2005Inventory
#0022652-17
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
Training Manual
Simulation Basics
C. Basic Procedure
• The purpose of simulation is usually to determine the response of the system based on some type of excitation or loading.
• It is crucial to remember that a mathematical model is used:– CAD geometry is an idealization of the physical model
– The mesh is a mathematical representation of the CAD model
– The accuracy of answers is determined by various factors:• How well the physical model is represented depends on the assumptions
• Numerical accuracy is determined by the mesh density
CAD Model Finite Element Mesh
August 26, 2005Inventory
#0022652-18
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
Training Manual
Simulation Basics
… Basic Procedure
• Every analysis involves four main steps:– Preliminary Decisions
• What type of analysis: Static, modal, etc.?
• What to model: Part or Assembly?
• Which elements: Surface or Solid Bodies?
– Preprocessing• Attach the model geometry
• Define and assign material properties to parts
• Mesh the geometry
• Apply loads and supports
• Request results
– Solve the Model
– Postprocessing• Review results
• Check the validity of the solution
Preprocessing
Solution
Postprocessing
Preliminary Decisions
August 26, 2005Inventory
#0022652-19
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
Training Manual
Simulation Basics
… Basic Procedure
• A sample analysis using the Stress Wizard will be shown in this section.
• The Wizards in Simulation aid the user in following the basic analysis template discussed previously:– Attach/import geometry
– Assign material properties
– (Mesh geometry)• A default mesh will be supplied by Simulation if this step is not
performed manually by the user
– Apply loads and supports
– Request results
– Solve model
– Review results/postprocessing
August 26, 2005Inventory
#0022652-20
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
Training Manual
Simulation Basics
… Attach Geometry
• Earlier, it was shown that geometry can be attached to Simulation in two ways– Direct from CAD system
• For supported CAD packages only using plug-in mode
– From within a blank Simulation session• For all supported formats, using plug-in or reader mode
Attaches active CAD model(plug-in mode)
Browse for CAD file(reader mode)
Directly launches Simulation and attaches geometry (plug-in mode)
Method 1 Method 2
August 26, 2005Inventory
#0022652-21
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
Training Manual
Simulation Basics
… Assign Material Properties
• After importing a model, the Stress Branch template was chosen, and the Stress Wizard appears– “Verify Materials” is selected, and the callout shows how to
change material properties in the pull-down menu
After “Verify Materials” is selected, all of the parts from the “Geometry” branch are highlighted, and the Details view shows how to change the material.
August 26, 2005Inventory
#0022652-22
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
Training Manual
Simulation Basics
• Notice that the Details View allows the user to select a material from a pull-down menu or to import a new material– The default material property is “Structural Steel” but can be
changed
– By selecting “Import …” the user can select a material property file (XML format)
– Although a few material properties are supplied with Simulation for demonstration purposes. Users should use their own material property values in production use.
… Assign Material Properties
August 26, 2005Inventory
#0022652-23
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
Training Manual
Simulation Basics
… Assign Material Properties
• Materials may be individually selected for each part– Multiple parts can be highlighted and changed at once
• Use Shift-Left mouse button to highlight all items in range
• Use Ctrl-Left mouse button to individually add/remove selection
ANSYS License AvailabilityDesignSpace EntraDesignSpace xProfessional xStructural xMechanical/Multiphysics x
By using a combination of Shift-Left mouse button and Ctrl-Left mouse button, twelve parts are highlighted on the Outline Tree
The user can then change all materials at once in the Details View by selecting the material pull-down menu.
Note that DesignSpace Entra is limited to analysis of single parts.
August 26, 2005Inventory
#0022652-24
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
Training Manual
Simulation Basics
… Assign Material Properties
• Material properties are listed, modified, imported or exported by accessing the “Engineering Data” application via the “Data” icon in Simulation
August 26, 2005Inventory
#0022652-25
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
Training Manual
Simulation Basics
… Assign Material Properties
• Default settings for material properties can be changed in the Engineering Data application– The default material can be changed from “Structural Steel”
– A list of “Favorites” can be saved for frequent access
– New materials can be added from various locations
August 26, 2005Inventory
#0022652-26
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
Training Manual
Simulation Basics
… Insert Loads & Supports
• After verifying and assigning materials, the “Insert Loads” item is selected from the Stress Wizard– Structural (and thermal) loads are applied from the pull-down
icon in the Context toolbar.
After “Insert Loads” is selected, notice that the “Environment” branch is highlighted.
By highlighting the “Environment” branch, the Context toolbar and Details view change.
August 26, 2005Inventory
#0022652-27
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
Training Manual
Simulation Basics
… Insert Loads & Supports
• Loads and supports are applied on geometric entities
• There are two ways to accomplish this:– Select geometry entity in Graphics Window first,
then select load or support from Context Toolbar
– Select load or support from Context Toolbar first, select geometry entities in Graphics Window, then click on “Apply” in Details View.
August 26, 2005Inventory
#0022652-28
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
Training Manual
Simulation Basics
… Insert Loads & Supports
• After assigning the load on geometric entities, the user can enter additional data in the Details view, if necessary.– Notice that, in the Outline Tree, the associated load branch
symbol status will also change to ‘completed’ (checkmark)
August 26, 2005Inventory
#0022652-29
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
Training Manual
Simulation Basics
… Insert Loads & Supports
• For some structural loads direction is needed:– Selection is done in Details View of load
• If “Components” is chosen, enter X, Y, or ZComponents of loading
• If “Vector” is chosen, select geometry andenter magnitude of loading
• Defaults can be set in “Tools > Options … > Simulation: Miscellaneous > Load Orientation Type”
– The World Coordinate System or user defined local coordinate systems can be referenced
• User-Defined Coordinate Systems will be discussed later
August 26, 2005Inventory
#0022652-30
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
Training Manual
Simulation Basics
… Insert Loads & Supports
– Existing geometry can be referenced to control direction:
• In the “Details” view, select “Define By: Vector”
• Three types of existing geometry can be used
– Normal to planar face or along axis of cylindrical face
– Along straight edge or normal to cylindrical edge
– Two vertices defining vector
• Click on “Direction” and select geometry used forvector orientation. Use the arrows in the Graphics window to toggle the direction.
• Click on “Apply” when done.
• Enter magnitude for loading in “Magnitude.”
August 26, 2005Inventory
#0022652-31
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
Training Manual
Simulation Basics
… Mouse Controls
– The left mouse button is used to select geometric entities OR to manipulate the graphics display
• User can select items (vertex, edge, surface, body) or manipulate the view (rotate, pan, zoom in/out, box zoom)
• Select mode can be single-select or box-select
– In single-select mode, click-drag with left mouse button to “paint select” multiple items
– Use Ctrl-Left mouse button in single-select mode to select or unselect multiple entities
– In box-select mode, click-drag from left to right selects entities fully enclosed in bounding box
– In box-select mode, click-drag from right to left selects any entity partially enclosed in bounding box
August 26, 2005Inventory
#0022652-32
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
Training Manual
Simulation Basics
… Mouse Controls
– In select mode the middle mouse provides several short cuts for graphics manipulation
• Click-drag middle mouse button to dynamically rotate model
• Shift-Middle mouse button pans model
• If present, the wheel can be used to zoom in/out
– The right mouse button provides context-sensitive pop-up menu if clicked once in Graphics Window
• Click-drag right mouse button to box zoom in area of interest
• Click right mouse button once and select “Fit” to fit model in view
Single-click right mouse button provides context-sensitive pop-up menu
Click-drag right mouse button allows user to box-zoom in region
August 26, 2005Inventory
#0022652-33
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
Training Manual
Simulation Basics
… Applying Loads and Supports
• By taking advantage of the mouse controls, it can be relatively easy to apply a load (or support) to multiple faces– In example below, user can use Ctrl-left mouse button to
single-select surfaces (highlighted in green)
– Use of middle mouse button allows user to rotate model to more easily select certain surfaces in ‘back’ of model
August 26, 2005Inventory
#0022652-34
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
Training Manual
Simulation Basics
… Insert Results
• By selecting the Stress Branch template in the beginning, some results are already requested. However, the user can request other results, if needed.– By selecting “Insert Results” in the Stress Wizard, the callout
shows how to add results
Note that the “Solution” branch is now highlighted.
Because the “Solution” branch is selected, the Context toolbar and Details view changes.
Results, such as stress, strain, and deformation can be requested from the pull-down icons on the Context toolbar. New result items will then appear under the “Solution” branch.
August 26, 2005Inventory
#0022652-35
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
Training Manual
Simulation Basics
… Solving the Model
• After verifying materials, applying loads and supports, and inserting results, the model is ready to be solved.– Selection of “Solve” in the Stress Wizard produces a callout
showing the user that the lightning bolt icon is used to initiate a solution
Starting the solution will include automatically meshing the model if it has not been done so previously.
The solution may take a few minutes to a few hours, depending on how large the model is and the hardware used. A progress bar will be shown to indicate roughly how long the solution will take. The solution can also be stopped via the progress bar.
August 26, 2005Inventory
#0022652-36
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
Training Manual
Simulation Basics
… Solving the Model (ANSYS Details)
– During solution an ANSYS input file is generated, and the details of the Output File can be viewed if a “Solution Information” branch has been requested under the “Solution” branch
In Worksheet view of the “Solution Information” branch, the contents of the Output File will be updated with a frequency as specified in the Details view.
The location of the input file “ds.dat,” output file “solve.out,” and scratch files are located in the system TEMP directory by default.
This solver directory can be changed under “Tools > Options… > Simulation: Solution > Solver Working Directory”
Advanced ANSYS Details
August 26, 2005Inventory
#0022652-37
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
Training Manual
Simulation Basics
… View Results
• After the solution is complete, the user can View Results– Plot contours and vectors by highlighting the result of interest
– Animate results via the “Animation” Tab
To view results, as the callout shows, the appropriate branch needs to be selected.
August 26, 2005Inventory
#0022652-38
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
Training Manual
Simulation Basics
… View Report
• In preparation for generating the HTML report, one can add figures and comments from the Standard Toolbar– Select a branch first, such as “Equivalent Stress”
– Then select the appropriate Standard Toolbar button:
August 26, 2005Inventory
#0022652-39
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
Training Manual
Simulation Basics
… View Report
• After adding any figures or comments, select “View Report”– Preliminary information can be entered, such as author name
– Select “Generate Report” to create HTML report
The HTML Report can be selected under the “Solution” branch via “Report Preview” tab, as the callout indicates.
August 26, 2005Inventory
#0022652-40
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
Training Manual
Simulation Basics
… View Report
• The HTML report will be displayed in Simulation– Comments and figures added will appear in the report
The HTML report generator includes all input and results associated with the simulation, providing complete documentation of the analysis.
This provides time-saving yet customizable report that can easily be generated by the user.
August 26, 2005Inventory
#0022652-41
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
Training Manual
Simulation Basics
… View Report
• Reports are always dynamically generated, so the user needs to save the report, otherwise it will be overwritten– The report can be “published” as HTML files in a different
directory or an internal web server, emailed, or sent to Microsoft Word or PowerPoint
The Appendix at the end of the HTML Report will show the location of the various files used to created the report.
August 26, 2005Inventory
#0022652-42
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
AN
SY
S W
ork
ben
ch
– Sim
ula
tion
Training Manual
Simulation Basics
• Workshop 2 – Simulation Basics
• Goal:– Using the Stress Wizard, set up and solve a structural model
for stress, deflection and safety factor.
D. Workshop 2 – Simulation Basics
top related