rtm_tx130-tx140-tx170_en
Post on 02-Jan-2016
29 Views
Preview:
DESCRIPTION
TRANSCRIPT
TABLE OF CONTENTS 0-1
PageJobe Code
GENERAL 1Description of CARES system machine locations and job codes 1-1Machine location and prime part 1-2Job codes 1-3Job time 1-3Troubleshooting time 1-4Welding time 1-4No job time provided (open box) 1-4Definition of terms used 1-5Service codes 1-6Request for supplementary Job Code or modification of time allowed 1-8
IVECO ENGINE 2MAINTENANCE xxxxxTROUBLESHOOTING xxxxxREMOVAL & INSTALLATION OR OVERHAUL xxxxxRADIATOR, RADIATOR CAP AND RADIATOR HOSES 023211FAN BELT 023215WATER PUMP AND HOUSING 023217WATER MANIFOLDS, OUTLETS AND THERMOSTATS 023219AIR FILTER AND PRE-FILTERS 023221RADIATOR HOSES AND AIR INTAKE PIPES 023223TURBOCHARGER 023225INTAKE MANIFOLD, INTERCOOLER 023227SILENCER AND EXHAUST EXTENSIONS 023231EXHAUST MANIFOLDS AND PIPES 023233CRANKSHAFT PULLEY, TIMING GEAR CASE AND SEAL 023261HEAT EXCHANGERS AND FILTER BASE 023275
IVECO FUEL SYSTEM 3MAINTENANCE xxxxxTROUBLESHOOTING xxxxxFUEL TANK 033211PIPING, PIPES AND FUEL HOSES 033213FUEL FEED PUMP 033215FUEL INJECTION PUMP 033231FUEL INJECTION PIPES 033233FUEL INJECTORS 033235FUEL SHUT-OFF AND ACCELERATOR 033243
Cre 9-88850 Issued 07-03
TABLE OF CONTENTS 0-2
ELECTRICAL SYSTEM 4TROUBLESHOOTING xxxxxWIRING FOR THE CHASSIS FRAME, THE TRANSMISSION OR THE MAIN WIRING 040120ENGINE WIRING 040140CAB WIRING 040170CIRCUIT-BREAKER AND RELAY 040510FUSES 040520SELECTOR SWITCHES AND SWITCHES 041510KEY STARTING SWITCH 041512SOLENOID (OTHER THAN STARTER) 041520AUDIBLE WARNING DEVICE 042031INSTRUMENT PANEL 042040STARTER MOTOR 042510STARTER MOTOR SOLENOID 042520CABLE AND BATTERY 042550ALTERNATOR 043010DRIVING LIGHT CIRCUIT 043510BRAKE LIGHT AND TAIL LIGHT CIRCUIT 043520TURN SIGNAL AND HAZARD WARNING LIGHT CIRCUIT 043530WORKING LIGHT CIRCUIT 043550INTERIOR LIGHTING, ROOF LAMP AND INSTRUMENT PANEL LIGHTING 043560ROTARY LIGHT 043570WINDSCREEN WIPER MOTOR 044020OPERATOR’S CONVENIENCE ACCESSORIES 044580LEVELLING CONTROL CIRCUIT 046038ELECTRICAL CONTROLLERS 046039ELECTRONIC CONTROLS 047020
STEERING SYSTEM 5STEERING WHEEL AND STEERING COLUMN 050110TIE RODS AND STEERING RODS 050140WHEELS AND WHEEL RIMS 050320PIPES BETWEEN THE PUMP AND THE STEERING VALVE 050733RETURN PIPING 050735STEERING VALVE 050743FLOW REGULATOR OR DIVIDER 050747HYDRAULIC STEERING PIPES 050751STEERING CYLINDERS 050761
Cre 9-88850 Issued 07-03
TABLE OF CONTENTS 0-3
POWERTRAIN 6MAINTENANCE xxxxxREMOVAL & INSTALLATION OR OVERHAUL xxxxxTORQUE CONVERTER 061010RESERVOIR AND FILTER 062311POWERSHIFT GEARBOX HYDRAULIC PIPING 062315POWERSHIFT GEARBOX CONTROL VALVE 062317CLUTCHES 062321SHAFTS, BEARINGS AND RINGS 062323HOUSING 062335AXLES AND DIFFERENTIALS 063110AXLE SHAFT BALL AND ROLLER BEARINGS AND BUSHINGS 063111PLANETARY CARRIER SHAFT 063120TRANSMISSION DRIVE SHAFTS 063161
BRAKES 7MAINTENANCE xxxxxBRAKE FLUID RESERVOIR 071013BRAKE PIPES 071041CONTROL VALVES 071053MASTER CYLINDER 071055BRAKE PISTONS 071071BRAKE DISKS 071073
HYDRAULIC SYSTEM 8MAINTENANCE xxxxxHYDRAULIC RESERVOIR 081611MAIN CIRCUIT PUMP 081621SUPPLY PIPES 081631RETURN PIPES 081635CONTROL VALVE 081643SOLENOID VALVE BLOCK 081645LIFTING/COMPENSATION CIRCUIT 081653TELESCOPIC CIRCUIT 081654TILT CIRCUIT 081655PILOT CIRCUIT 081656AUXILIARY CIRCUIT 081657STABILIZER CYLINDERS 081661AXLE LOCKING CYLINDERS 081662LIFTING/COMPENSATION CYLINDERS 081663TELESCOPIC CYLINDERS 081664TILT CYLINDER 081665HYDRAULIC OIL COOLER 081681HAND LEVER 081691
Cre 9-88850 Issued 07-03
TABLE OF CONTENTS 0-4
CHASSIS/ATTACHMENTS 9MAINTENANCE xxxxxMAIN CHASSIS FRAME 090111COUNTERWEIGHT 090117HOODS, SIDE PANELS AND SERVICE ACCESS POINTS 090131FENDERS, STEPS AND LADDERS 090133PAINT AND ADHESIVE 090137CAB FRAME, ROOF AND CAB ATTACHMENTS 090311CAB DOORS AND WINDOWS 090313HEATING AND DEFROSTING SYSTEM 090315INSTALLATION OF OPERATOR’S CONSOLE TRIM, THE INSTRUMENT PANEL AND THE STEERING COLUMN 090318
INSULATION AND CAB CEILING 090319SEATS AND BRACKETS 090331SAFETY BELTS 090333STABILIZER LEGS AND PADS 091631TELESCOPIC ARM 091636
Cre 9-88850 Issued 07-03
GENERAL 1 - 1
Cre 9-88850 Issued 07-03
Description of CARES system machine locations and job codes
a) Machine location code
NOTE: The machine location codes are given on table of contents.
b) Job code
02 32 21 A
The 1st and 2nd digits indicate the machine locations and correspond to the chapters in the service manuals
The 3rd and 4th digits indicate the main components
or assemblies
The 5th and 6th digits indicate the sub-assemblies
The 7th element is an alphabet that refers to the work codes
and the working hours
02 = Engine
023221
32 = Air intake system
21 = Air filter and pre-filter
02 = Engine
023221A
32 = Air intake system
21 = Air filter and pre-filter
A = R & I of the air pre-filter; 0.1 hour
GENERAL 1 - 2
Cre 9-88850 Issued 07-03
Machine location and prime partThe machine location must be specified on the warranty claim form; It shows the location of the "Prime part" onthe machine.
The "Prime part" refers to the part that caused the breakdown.
Example:
If the "Prime part" is a nut, a bolt, an O-ring, a gasket, a seal or other hardware item, select the machinelocation corresponding to the location of the component which the item is a part of, or to which it is attached. Forexample, if a bolt on a connecting rod is broken, the bolt would be listed as the "Prime part" and the machinelocation of the connecting rod would be used.
CAUTION!
Never use the job codes given below to refer to the machine locations:
Codes ending in ...01 (MAINTENANCE), ...02 (TROUBLESHOOTING), ...03 (REMOVAL AND INSTALLATIONOR OVERHAUL) are for job codes only and are never machine locations since they cannot indicate a locationfor the "Prime part" which caused the breakdown.
Service codesService codes are specified on the warranty claim to identify "How" and "Why" the "Prime part" caused thebreakdown. Only the approved service codes listed on page 1-6 may be used.
Water pump and housing 023217
R & I of the water pump .......................................... 0.6 0.6 0.6 023217A
Overhaul of the water pump.................................... 1.5 1.5 1.5 023217B
Maintenance TroubleshootingRemoval
and installation or overhaul
023201033201060001070001080001090001
023202033202040002
023203060003
XXXX XXXX XXXXXXXXMachine location
Job code
GENERAL 1 - 3
Cre 9-88850 Issued 07-03
Job codesThe job code (a six digit number followed by an alphabetical character) must be specified on the warranty claimform in order to be reimbursed for labour costs. Selection of job codes should cover all repairs performed incorrecting the problem. The job code can be different from the machine location code but most of the time it willbe the same.
Example:
Job timeThe CARES manuals have been designed so that the warranty claim forms can be completed with one job codefor each "Prime part".
When a job time is given, it covers all operations necessary to perform the jobs it prescribes. The jobtime includes the Removal and Installation of all parts or components that may have been removed toaccess the defective part or component.
Job time (labour hours) in the column under the machine models to which the job code applies, is given in hoursand tenths of hours.
indicates that the job code does not apply to this particular model.
open box (no indication of time) means a time has not been determined for this model but the job codeis applicable.
Because the manuals are written in this style, there is the occasional warranty claim form that will combine(overlap) two job codes which include the R & I of the same part in each job time given.
The system will approve and pay the hours requested under a job code as long as the requested hours do notexceed the given job time.
As a result, when two job codes are combined, the removal and installation should be deducted from one of thetwo job codes. The number of hours obtained in this way should be entered on the warranty claim form.
Example:
R & I of water pump and overhaul of water pump. The corresponding job codes 023217A and 023217B bothinclude the R & I of the water pump. The request for a TX130 Telehandler should therefore be:
023217A 023217B Total
0.6 + 0.9 = 1.5
The indication of the time 0.9 hours under the 023217A code corresponds to its own time, or 1.5 hours, fromwhich the 0.6 hours of the 023217A code corresponding to the R & I of the water pump have been deducted.
Fan belt 023215
Adjusting the tension of the water pump and alternator belt .......................................................... 0.2 0.2 0.2 023215A
XXXX XXXX XXXXXXXX Machine locationJob code
***
GENERAL 1 - 4
Cre 9-88850 Issued 07-03
Troubleshooting timeTroubleshooting is a specific job. Times are listed in various sections of the manual for the hook-up of the testinstruments and the proper running of the test requires.
Only is in specific cases is troubleshooting included as part of the job time. For example, R & I of the main reliefvalve includes pressure testing and adjusting just as R & I of the secondary relief valve includes hand-pumpingand adjusting. If troubleshooting time is included, it will be noted in the job description.
Welding timeWith the flat rate times, welding (when performed by the dealership) is the only additional time to be considered.All requests for welding must be accompanied with a job code.
A request for welding is to be made by picking the job code for the component or part of which the welding wasperformed and then adding the letter "W" as a second alphabetical character to the job code.
Example:
The job code for the cab is 090311A. Welding would be requested under job code 090311AW and labourcalculated using the following guidelines:
No job time provided (open box)A repair request should always be accompanied by a job code. However, if no indication of time is given, it mustbe calculated considering:
1 That a highly qualified mechanic has performed the repairs, in the dealership’s "certified" shop.
2 Include in the job time, cleaning of the area to be repaired and the actual repair job including associatedproblems encountered.
3 Troubleshooting performed should be requested by the appropriate troubleshooting job code.
GENERAL 1 - 5
Cre 9-88850 Issued 07-03
Definition of terms used
R & I (Removal and Installation)This term refers to the Removal of an existing part or component and the Installation of this same part orcomponent or of a different part or component. This term also includes the R & I of all parts or componentsnecessary to gain access to the part or component determined.
Example:
ReplacementThis term indicates the removal of an existing part and the installation of a new or different part.
Example:
OverhaulThis term includes:
The removal and installation of a component.Complete disassembly.Checking for the absence of any trace of wear or damage.Cleaning all the parts.Complete assembly and checking all tolerances.Replacing the related filter cartridges.Renewing all oils and lubricants used.Replacing all seals, gaskets, O-rings, etc.The proper running in of new parts and all the adjustments, where necessary.
Example:
Radiator, radiator cap and radiator hoses 023211
R & I of the radiator ................................................... 1.6 1.6 1.6 023211A
Silencer and exhaust extensions 023231
Replacing the exhaust silencer ............................... 0.7 0.7 0.7 023231A
Water pump and housing 023217
Overhaul of the water pump ........................................ 1.5 1.5 1.5 023217B
XXXX XXXX XXXXXXXX Machine locationJob code
XXXX XXXX XXXXXXXXMachine location
Job code
XXXX XXXX XXXXXXXX Machine locationJob code
SERVICE CODES (Alphabetical) 1 - 6
Cre 9-88850 Issued 07-03
Abnormal noise .................................................... 065Adjustment (why?) ............................................... 010Appearance (describe, visual consequences) ..... 015Assembly ............................................................. 005Backfire (engine injection).................................... 210Backlash (describe) ............................................. 020Banging................................................................ 065Blistered............................................................... 035Blocked (describe) ............................................... 040Bonding/assembly................................................ 005Brazed.................................................................. 365Broken.................................................................. 365Buckling (rod)....................................................... 050Burned ................................................................. 055Chipped/nicked (chains, gearing) ........................ 070Clamping/retaining - poor/none............................ 075Clogging (where?)................................................ 255Condensation (electricity, diesel oil, oil) ............... 220Contaminated (describe)...................................... 090Corroded.............................................................. 260Cracked (describe, cast parts, blocks)................. 095Cracked (pipes, hoses) ........................................ 030Cracked................................................................ 365Crushed ............................................................... 080Cut through (flexible parts)................................... 105Deep grooves (hydraulic motor)........................... 155Does not engage (mechanical) .............................110Does not return (mechanical)................................115Elongated............................................................. 120Elongation (belts, chains)..................................... 310End play ............................................................... 125Erratic/fluctuating ................................................. 130Faulty connection (electricity, electronic) ............. 085Field survey.......................................................... 136Flaking
(paint, chromium plated parts, tyres) ............... 140Folded, bent ......................................................... 025Forgotten part ...................................................... 231Fraying (belt)........................................................ 145Glazing (engine)................................................... 150Grazed (rubber parts, tyres)................................. 265High fuel consumption (motor)............................. 160High oil consumption (motor) ............................... 165Humidity (electricity, diesel oil, oil) ....................... 220Incorrect alignment
(by how much? Mechanical consequences).... 205Interference.......................................................... 170Internal leaks (hydraulic)...................................... 060
Jumped out of its groove (circuit seals) ............... 230Jumps out of gear ................................................ 175Knotted (cable, piping, seals)............................... 180Laminating (rolled parts) ...................................... 185Leak ..................................................................... 100Length (describe) ................................................. 195Loose ................................................................... 200Marked................................................................. 025Misfiring (engine injection) ................................... 210Mismachined (how?)............................................ 215
Not sealing properly ............................................. 225Notched (rubber parts, tyres) ............................... 265Obstructed (describe) .......................................... 040Off-centre when rotating....................................... 345Open circuit (electrical) ........................................ 228Ovalization ........................................................... 120Overspeeding (travel motor) ................................ 320
Parts unscrewed .................................................. 135Parts which have been dropped .......................... 135Pinched (cable, piping, seals) .............................. 180Pin-holes .............................................................. 235Pitted.................................................................... 240Porosity ................................................................ 235Pre-delivery after leaving the factory
(between zeo and five hours only)................... 555Pressure high....................................................... 245Pressure low ........................................................ 250Roughness (engine)............................................. 150Rubbing................................................................ 170Rupture ................................................................ 045Rusted.................................................................. 260Scratched (rubber parts, tyres) ............................ 265Seized .................................................................. 270Separation
(paint, chromium plated parts, tyres) ............... 140Service modification programme
(implementation note only) .............................. 275Sheared ............................................................... 280Shifting difficult (mechanical) ............................... 285Short circuit (electrical, electronic) ....................... 290Short shipment
(machines assembled on site only) ................. 950Slipping ................................................................ 295Slow lowering....................................................... 100Soft consistency................................................... 300Spongey consistency ........................................... 300Squeezed out (circuit seals)................................. 230Sticking/binding.................................................... 305Stripped/pulled out (threaded items) .................... 315Surging (travel motor) .......................................... 320Swollen (pipes, hoses)......................................... 030Temperature too high ........................................... 325Temperature too low ............................................ 330Tension (belts, chains) ......................................... 310Torn (flexible parts) .............................................. 105Torque high (engine, hydraulic motor) ................. 335Torque low (engine, hydraulic motor) ................... 340Turned.................................................................. 345Twisted................................................................. 350Vibrations (describe) (welds)................................ 355Wear/worn (describe)........................................... 360Welded ................................................................. 365Would not hold charge (electricity)....................... 370
SERVICE CODES (Numerical) 1 - 7
Cre 9-88850 Issued 07-03
Assembly ............................................................. 005Bonding/assembly................................................ 005Adjustment (why?) ............................................... 010Appearance (describe, visual consequences) ..... 015Backlash (describe) ............................................. 020Marked................................................................. 025Folded, bent ......................................................... 025Cracked (pipes, hoses) ........................................ 030Swollen (pipes, hoses)......................................... 030Blistered............................................................... 035Blocked (describe) ............................................... 040Obstructed (describe) .......................................... 040Rupture ................................................................ 045Buckling (rod)....................................................... 050Burned ................................................................. 055Internal leaks (hydraulic)...................................... 060Abnormal noise .................................................... 065Banging................................................................ 065Chipped/nicked (chains, gearing) ........................ 070Clamping/retaining - poor/none............................ 075Crushed ............................................................... 080Faulty connection (electricity, electronic) ............. 085Contaminated (describe)...................................... 090Cracked (describe, cast parts, blocks)................. 095Slow lowering....................................................... 100Leak ..................................................................... 100Torn (flexible parts) .............................................. 105Cut through (flexible parts)................................... 105Does not engage (mechanical) .............................110Does not return (mechanical)................................115Elongated............................................................. 120Ovalization ........................................................... 120End play ............................................................... 125Erratic/fluctuating ................................................. 130Parts unscrewed .................................................. 135Parts which have been dropped .......................... 135Field survey.......................................................... 136Separation
(paint, chromium plated parts, tyres) ............... 140Flaking
(paint, chromium plated parts, tyres) ............... 140Fraying (belt)........................................................ 145Glazing (engine)................................................... 150Roughness (engine)............................................. 150Deep grooves (hydraulic motor)........................... 155High fuel consumption (motor)............................. 160High oil consumption (motor) ............................... 165Rubbing................................................................ 170Interference.......................................................... 170Jumps out of gear ................................................ 175Knotted (cable, piping, seals)............................... 180Pinched (cable, piping, seals) .............................. 180Laminating (rolled parts) ...................................... 185Length (describe) ................................................. 195
Loose ................................................................... 200Incorrect alignment
(by how much? Mechanical consequences).... 205Misfiring (engine injection) ................................... 210Backfire (engine injection).................................... 210Mismachined (how?) ............................................ 215Condensation (electricity, diesel oil, oil) ............... 220Humidity (electricity, diesel oil, oil) ....................... 220Not sealing properly ............................................. 225Open circuit (electrical) ........................................ 228Squeezed out (circuit seals)................................. 230Jumped out of its groove (circuit seals) ............... 230Forgotten part ...................................................... 231Porosity ................................................................ 235Pin-holes .............................................................. 235Pitted.................................................................... 240Pressure high....................................................... 245Pressure low ........................................................ 250Clogging (where?)................................................ 255Corroded .............................................................. 260Rusted.................................................................. 260Notched (rubber parts, tyres) ............................... 265Grazed (rubber parts, tyres)................................. 265Scratched (rubber parts, tyres) ............................ 265Seized .................................................................. 270Service modification programme
(implementation note only) .............................. 275Sheared ............................................................... 280Shifting difficult (mechanical) ............................... 285Short circuit (electrical, electronic) ....................... 290Slipping ................................................................ 295Soft consistency................................................... 300Spongey consistency ........................................... 300Sticking/binding.................................................... 305Elongation (belts, chains)..................................... 310Tension (belts, chains) ......................................... 310Stripped/pulled out (threaded items) .................... 315Overspeeding (travel motor) ................................ 320Surging (travel motor) .......................................... 320Temperature too high ........................................... 325Temperature too low ............................................ 330Torque high (engine, hydraulic motor) ................. 335Torque low (engine, hydraulic motor) ................... 340Off-centre when rotating....................................... 345Turned.................................................................. 345Twisted................................................................. 350Vibrations (describe) (welds)................................ 355Wear/worn (describe)........................................... 360Brazed.................................................................. 365Broken.................................................................. 365Cracked................................................................ 365Welded ................................................................. 365Would not hold charge (electricity)....................... 370Pre-delivery after leaving the factory
(between zeo and five hours only)................... 555Short shipment
(machines assembled on site only) ................. 950
Cre 9-88850 Issued 07-03
REQUEST FOR SUPPLEMENTARY JOB CODE OR MODIFICATION OF TIME ALLOWED 1 - 8
Reference number of form used : .........................................................
Model concerned : .........................................................
Machine location : .........................................................
Request to add a job code
Closest existing job code: ......................................................................................................................................................................................................................................................................................................................
Description of the job code requested: ..................................................................................................................................................................................................................................................................................................
Estimated time for the requested job code: ...........................................................................................................................................................................................................................................................................................
Request for changing the time allowedIMPORTANT: All requests for modifications must be supported by copies of the job cards, and details of timespent, etc.
Job code : .................................................
Time allowed : .................................................
Time requested : .................................................
Case store or dealer _____________________________
Town __________________________________________
Phone No. ______________________________________
Signature ______________________________________
Date ___________________________________________
The Product Support Manager is authorized to study all requests for modification of time spent, concerning agiven job code. Attach all the documents necessary for studying the case: workshop job cards, details oftime spent, etc.
CNH FRANCE17, Rue des TournellesB.P. 30660803 CREPY-EN-VALOIS Cedex
Attn: Product Support Manager
Complete this form and send it to:
for the machine concerned
FRANCE
ENGINEIVECO
2-1
TX13
0
TX14
0
TX17
0 MachineLocationJob Code
MAINTENANCE xxxxxReplacing the oil filter cartridge 0.2 0.2 0.2 023201AReplacing the engine oil 0.5 0.5 0.5 023201BDraining and replacing the engine oil filter cartridge 0.7 0.7 0.7 023201CFlushing the engine with a special oil (including draining and changing the oil filter) 1.8 1.8 1.8 023201D
Replacing the air filter cartridges 0.1 0.1 0.1 023201EReplacing the engine coolant 0.4 0.4 0.4 023201F
TROUBLESHOOTING xxxxxChecking the engine compression 1.9 1.9 1.9 023202A
REMOVAL & INSTALLATION OR OVERHAUL xxxxxEngine and transmission, assembly - R & I from machine 6.0 6.0 6.0 023203A
Bench testing and adjusting the engine 7.0 7.0 7.0 023203BEngine - Removing from transmission, on bench 1.2 1.2 1.2 023203C
COOLING CIRCUIT
RADIATOR, RADIATOR CAP AND RADIATOR HOSES 023211R & I of the radiator 1.6 1.6 1.6 023211AChecking the radiator for leaks 0.9 0.9 0.9 023211BR & I of the expansion tank 0.5 0.5 0.5 023211C
FAN BELT 023215Adjusting the tension of the water pump and alternator belt 0.2 0.2 0.2 023215A
Replacing the water pump and alternator belt 0.5 0.5 0.5 023215BReplacing the fan assembly 0.3 0.3 0.3 023215CReplacing the fan pulley and support (belt stretcher) 0.4 0.4 0.4 023215D
WATER PUMP AND HOUSING 023217R & I of the water pump 0.6 0.6 0.6 023217AOverhaul of the water pump (including job code 023217A) 1.5 1.5 1.5 023217B
WATER MANIFOLDS, OUTLETS AND THERMOSTATS 023219Replacing the coolant thermostat on the water pump 0.5 0.5 0.5 023219A
Cre 9-88850 Issued 07-03
ENGINEIVECO
2-2
TX13
0
TX14
0
TX17
0 MachineLocationJob Code
AIR INTAKE SYSTEMAIR FILTER AND PRE-FILTERS 023221R & I of the air pre-filter 0.1 0.1 0.1 023221AR & I of the air filter assembly 0.3 0.3 0.3 023221BReplacing the air filter body 0.2 0.2 0.2 023221C
RADIATOR HOSES AND AIR INTAKE PIPES 023223Replacing an air filter sleeve and hose 0.2 0.2 0.2 023223AReplacing the pipe (first line) 0.2 0.2 0.2 023223B
TURBOCHARGER 023225R & I of the turbocharger 1.0 1.0 1.0 023225A
INTAKE MANIFOLD, INTERCOOLER 023227R & I of the intake manifold (including replacement of the seal) 0.5 0.5 0.5 023227A
R & I of the aftercooler (including replacement of the elbows) 0.2 0.2 0.2 023227B
EXHAUST SYSTEM
SILENCER AND EXHAUST EXTENSIONS 023231Replacing the exhaust silencer 0.7 0.7 0.7 023231AReplacing the exhaust silencer pipe 0.2 0.2 0.2 023231BReplacing the evacuation pipe 1.0 1.0 1.0 023231C
EXHAUST MANIFOLDS AND PIPES 023233R & I of the exhaust manifold (including replacement of the seal) 1.2 1.2 1.2 023233A
CRANKSHAFT, CAMSHAFT AND TIMINGCRANKSHAFT PULLEY, TIMING GEAR CASE AND SEAL 023261R & I of the crankshaft pulley 0.7 0.7 0.7 023261A
HEAT EXCHANGERS AND FILTER BASE 023275R & I of the oil heater assembly 2.8 2.8 2.8 023275A
Cre 9-88850 Issued 07-03
FUEL SYSTEMIVECO
3-1
TX13
0
TX14
0
TX17
0 MachineLocationJob Code
MAINTENANCE xxxxxFuel filter, replace 0.2 0.2 0.2 033201A
TROUBLESHOOTING xxxxxChecking and timing the injection pump 0.4 0.4 0.4 033202A
FUEL RESERVOIR, PIPES AND FEED PUMPFUEL TANK 033211R & I of the fuel tank 1.7 1.7 1.7 033211A
PIPING, PIPES AND FUEL HOSES 033213Replacing the fuel delivery and return pipes on the filter 0.1 0.1 0.1 033213A
Replacing the fuel delivery hose between the reservoir and the fuel pump 0.3 0.3 0.3 033213B
Replacing the fuel return hose between the reservoir and the engine 0.3 0.3 0.3 033213C
FUEL FEED PUMP 033215R & I of the fuel feed pump 0.3 0.3 0.3 033215A
FUEL INJECTION CIRCUITFUEL INJECTION PUMP 033231R & I of the injection pump 1.5 1.5 1.5 033231A
FUEL INJECTION PIPES 033233Replacing one fuel injection tube 0.4 0.4 0.4 033233AReplacing the fuel injection tubes 0.9 0.9 0.9 033233B
FUEL INJECTORS 033235R & I of the fuel injectors (nozzle holder and nozzle) 1.5 1.5 1.5 033235A
FUEL SYSTEM CONTROLFUEL SHUT-OFF AND ACCELERATOR 033243Adjusting the acceleration control stroke 0.2 0.2 0.2 033243AR & I of the accelerator pedal 0.4 0.4 0.4 033243BReplacing the cable between the pedal and the pump 0.4 0.4 0.4 033243C
Cre 9-88850 Issued 07-03
ELECTRICAL SYSTEM 4-1
TX13
0
TX14
0
TX17
0 MachineLocationJob Code
TROUBLESHOOTING xxxxxChecking the density of the battery electrolyte (Add distilled water, if necessary) 0.3 0.3 0.3 040002A
Checking the alternator voltage 0.2 0.2 0.2 040002B
WIRING AND HARNESS
WIRING FOR THE CHASSIS FRAME, THE TRANSMISSION OR THE MAIN WIRING 040120R & I of the main chassis frame harness (front and rear) 3.5 3.5 3.5 040120A
ENGINE WIRING 040140R & I of the main engine harness 1.2 1.2 1.2 040140A
CAB WIRING 040170R & I of the main cab harness 4.3 4.3 4.3 040170A
CIRCUIT-BREAKERS, FUSES, RESISTORS AND DIODESCIRCUIT-BREAKER AND RELAY 040510R & I of the battery master switch 0.2 0.2 0.2 040510AR & I of the relay in the engine compartment 0.1 0.1 0.1 040510B
FUSES 040520Replacing a fuse in the engine compartment 0.1 0.1 0.1 040520AReplacing the fuse holder box in the cab 0.4 0.4 0.4 040520BReplacing the fuse holder box in the engine compartment 0.4 0.4 0.4 040520C
SWITCHES & CONTROLS
SELECTOR SWITCHES AND SWITCHES 041510R & I of the operation switch assembly 1.6 1.6 1.6 041510AR & I of the steering selection switch 1.6 1.6 1.6 041510BR & I of the switch 0.2 0.2 0.2 041510CR & I of the brake light contact switch (brake pedal) 1.5 1.5 1.5 041510DR & I of the transmission hand control 0.4 0.4 0.4 041510E
KEY STARTING SWITCH 041512R & I of the key starting switch 0.3 0.3 0.3 041512A
SOLENOID (OTHER THAN STARTER) 041520R & I of the solenoid for stabilizer and levelling cylinder 0.3 0.3 0.3 041520A
Cre 9-88850 Issued 07-03
ELECTRICAL SYSTEM 4-2
TX13
0
TX14
0
TX17
0 MachineLocationJob Code
INSTRUMENTS AND CONTROLS
AUDIBLE WARNING DEVICE 042031R & I of the horn 0.2 0.2 0.2 042031AR & I of the backup alarm 0.3 0.3 0.3 042031B
INSTRUMENT PANEL 042040R & I of the front instrument panel assembly 1.5 1.5 1.5 042040A
STARTER MOTOR AND BATTERY
STARTER MOTOR 042510R & I of the starter motor 1.0 1.0 1.0 042510AOverhaul of the starter motor (clean rotor and replace brush) 1.6 1.6 1.6 042510B
Replacing the starter inductor winding of the starter motor (without rotor) 1.1 1.1 1.1 042510C
STARTER MOTOR SOLENOID 042520Replacing the starter motor solenoid (including job code 042510A) 1.5 1.5 1.5 042520A
CABLE AND BATTERY 042550R & I of the battery 0.2 0.2 0.2 042550A
ELECTRICAL CHARGE SYSTEM COMPONENTSALTERNATOR 043010R & I of the alternator 0.8 0.8 0.8 043010AOverhaul of the alternator 1.6 1.6 1.6 043010B
LIGHTING AND SIGNAL DEVICES
DRIVING LIGHT CIRCUIT 043510R & I of the driving light assembly 0.2 0.2 0.2 043510AReplacing a driving light bulb 0.1 0.1 0.1 043510B
BRAKE LIGHT AND TAIL LIGHT CIRCUIT 043520R & I of a tail light assembly 0.2 0.2 0.2 043520AReplacing a bulb on the brake light or tail light 0.1 0.1 0.1 043520B
TURN SIGNAL AND HAZARD WARNING LIGHT CIRCUIT 043530Replacing a turn signal bulb 0.1 0.1 0.1 043530A
WORKING LIGHT CIRCUIT 043550R & I of a working light (front or rear) 0.2 0.2 0.2 043550A
Cre 9-88850 Issued 07-03
ELECTRICAL SYSTEM 4-3
TX13
0
TX14
0
TX17
0 MachineLocationJob Code
INTERIOR LIGHTING, ROOF LAMP AND INSTRUMENT PANEL LIGHTING 043560Replacing the roof lamp assembly 0.2 0.2 0.2 043560AReplacing the roof lamp bulb 0.1 0.1 0.1 043560B
ROTARY LIGHT 043570Replacing a rotary light bulb 0.1 0.1 0.1 043570A
ELECTRIC MOTORS
WINDSCREEN WIPER MOTOR 044020R & I of the front windscreen wiper motor 0.5 0.5 0.5 044020AR & I of the upper windscreen wiper motor 0.7 0.7 0.7 044020BReplacing the windscreen washer reservoir 0.4 0.4 0.4 044020C
ELECTRICAL ACCESSORIES
OPERATOR’S CONVENIENCE ACCESSORIES 044580R & I of the cigar lighter 0.7 0.7 0.7 044580AR & I of the socket power, inside cab 0.7 0.7 0.7 044580BR & I of the socket power, outside cab 0.4 0.4 0.4 044580C
ELECTRICAL SYSTEM
LEVELLING CONTROL CIRCUIT 046038R & I of the load monotor display 0.2 0.2 0.2 046038A
ELECTRICAL CONTROLLERS 046039R & I of the transmission electronic control unit 0.6 0.6 0.6 046039AR & I of the parking brake control unit 1.6 1.6 1.6 046039B
ELECTRONIC SYSTEM
ELECTRONIC CONTROLS 047020R & I of the fuel level sensor 0.4 0.4 0.4 047020A
Cre 9-88850 Issued 07-03
STEERING SYSTEM 5-1
TX13
0
TX14
0
TX17
0 MachineLocationJob Code
STEERING CONTROLSTEERING WHEEL AND STEERING COLUMN 050110Replacing the steering wheel 0.2 0.2 0.2 050110AReplacing the steering column 2.8 2.8 2.8 050110B
TIE RODS AND STEERING RODS 050140Replacing and adjusting the steering rod on the front or rear axle 0.5 0.5 0.5 050140A
WHEELS AND WHEEL RIMS 050320R & I of a wheel 0.3 0.3 0.3 050320AReplacing a tyre (including job code 050320A) 0.6 0.6 0.6 050320B
STEERING SYSTEM PIPESPIPES BETWEEN THE PUMP AND THE STEERING VALVE 050733Replacing a hose between the cab plate and the hydraulic pump 0.4 0.4 0.4 050733A
RETURN PIPING 050735Replacing the return hose between the cab plate and the hydraulic reservoir 0.5 0.5 0.5 050735A
STEERING VALVE 050743R & I of the steering valve 2.8 2.8 2.8 050743A
FLOW REGULATOR OR DIVIDER 050747R & I of the four wheel steering selection solenoid-operated valve block 0.6 0.6 0.6 050747A
HYDRAULIC STEERING PIPES 050751Replacing the hose between the rear axle and cab plate 0.4 0.4 0.4 050751A
Replacing the hose between the steering cylinder on the axle and the four wheel steering selection solenoid valve block
0.5 0.5 0.5 050751B
Replacing a hose between the steering valve and the cab plate 2.2 2.2 2.2 050751C
STEERING CIRCUIT CYLINDERSSTEERING CYLINDERS 050761R & I of a steering cylinder on the front or rear axle 2.0 2.0 2.0 050761AOverhaul of a steering cylinder on the front or rear axle 0.4 0.4 0.4 050761B
Cre 9-88850 Issued 07-03
TRANSMISSION 6-1
TX13
0
TX14
0
TX17
0 MachineLocationJob Code
MAINTENANCE xxxxxDraining and replacing the gearbox oil filter 0.4 0.4 0.4 060001ADraining oil from the rear axle 0.3 0.3 0.3 060001BDraining oil from the front axle 0.3 0.3 0.3 060001CDraining oil from the axle reduction (right or left, front or rear) 0.2 0.2 0.2 060001D
REMOVAL & INSTALLATION OR OVERHAUL xxxxxR & I of the gearbox 5.4 5.4 5.4 060003AR & I of the shaft drop box (including job code 060003A) 5.7 5.7 5.7 060003B
Overhaul of the shaft drop box (including replacement of any parts) 1.5 1.5 1.5 060003C
TORQUE CONVERTERTORQUE CONVERTER 061010R & I of the torque converter 5.4 5.4 5.4 061010AR & I of the torque converter with the engine removed 0.2 0.2 0.2 061010B
POWERSHIFT TRANSMISSIONRESERVOIR AND FILTER 062311Replacing the gearbox oil filter 0.2 0.2 0.2 062311A
POWERSHIFT GEARBOX HYDRAULIC PIPING 062315Replacing a hose between the gearbox and the oil cooler 2.0 2.0 2.0 062315A
POWERSHIFT GEARBOX CONTROL VALVE 062317R & I of the elettromagnet, transmission control valve (one) 0.1 0.1 0.1 062317A
R & I of the elettromagnet, transmission control valve (all) 0.3 0.3 0.3 062317B
Overhaul of the elettromagnet, transmission control valve (one) 0.3 0.3 0.3 062317C
R & I of the safety valve 0.1 0.1 0.1 062317DOverhaul of the safety valve 0.5 0.5 0.5 062317E
CLUTCHES AND SHAFTSCLUTCHES 062321Overhaul of the clutch 1.3 1.3 1.3 062321A
SHAFTS, BEARINGS AND RINGS 062323Overhaul of the gearbox shafts and pinions 1.3 1.3 1.3 062323A
Cre 9-88850 Issued 07-03
TRANSMISSION 6-2
TX13
0
TX14
0
TX17
0 MachineLocationJob Code
POWERSHIFT GEARBOX SHAFTS AND HOUSINGSHOUSING 062335Replacing the gearbox housings (including the removal and installation of the pinions and other components in the housings)
8.1 8.1 8.1 062335A
AXLES, SHAFTS AND DIFFERENTIALSAXLES AND DIFFERENTIALS 063110R & I of the front axle assembly 2.3 2.3 2.3 063110AR & I of the rear axle assembly 2.3 2.3 2.3 063110B
AXLE SHAFT BALL AND ROLLER BEARINGS AND BUSHINGS 063111Replacing the shafts and bearings on the front axle ball joint 2.5 2.5 2.5 063111A
PLANETARY GEARSPLANETARY CARRIER SHAFT 063120Overhaul of a planetary carrier 1.8 1.8 1.8 063120A
TRANSMISSION SHAFTSTRANSMISSION DRIVE SHAFTS 063161R & I of the front transmission shaft 0.3 0.3 0.3 063161AR & I of the rear transmission shaft 0.3 0.3 0.3 063161B
Cre 9-88850 Issued 07-03
BRAKES 7-1
TX13
0
TX14
0
TX17
0 MachineLocationJob Code
MAINTENANCE xxxxxAir bleed from the braking system 0.6 0.6 0.6 070001A
BRAKE FLUID RESERVOIR 071013Replacing the brake fluid reservoir 0.3 0.3 0.3 071013A
BRAKE SYSTEM PIPINGBRAKE PIPES 071041Replacing the hoses between the reservoir and the master cylinders 1.5 1.5 1.5 071041A
Replacing the pipes between the parking brake valve and the axle 0.6 0.6 0.6 071041B
Replacing the hose (drain circuit, not included) 0.3 0.3 0.3 071041CReplacing the hose between the master cylinder and the cab plate 1.6 1.6 1.6 071041D
MASTER CYLINDER AND DISTRIBUTOR VALVECONTROL VALVES 071053R & I of the parking brake valve 0.5 0.5 0.5 071053A
MASTER CYLINDER 071055R & I of a master cylinder (including job code 070001A) 2.2 2.2 2.2 071055A
PISTONS AND BRAKE DISKSBRAKE PISTONS 071071Overhaul of the parking brake caliper 0.8 0.8 0.8 071071A
BRAKE DISKS 071073R & I of the brake discs, right or left (single) 1.5 1.5 1.5 071073AR & I of the brake discs, right or left with axle removed (single) 0.6 0.6 0.6 071073B
Cre 9-88850 Issued 07-03
HYDRAULIC SYSTEM 8-1
TX13
0
TX14
0
TX17
0 MachineLocationJob Code
MAINTENANCE xxxxxDraining the hydraulic reservoir (filter cleaning included) 0.7 0.7 0.7 080001A
Washing the hydraulic reservoir 1.1 1.1 1.1 080001BReplacing the intake screen in the hydraulic reservoir 0.7 0.7 0.7 080001CReplacing the hydraulic oil filter element 0.3 0.3 0.3 080001D
RESERVOIRS AND HYDRAULIC FILTERSHYDRAULIC RESERVOIR 081611R & I of the hydraulic reservoir 1.7 1.7 1.7 081611A
HYDRAULIC PUMPMAIN CIRCUIT PUMP 081621R & I of the hydraulic pump 1.0 1.0 1.0 081621AR & I of the hydraulic pump with hoods and panel removed 0.5 0.5 0.5 081621B
R & I of the hydraulic pump with transmission removed 0.2 0.2 0.2 081621C
MAIN HYDRAULIC PIPING (SUPPLY/RETURN)SUPPLY PIPES 081631Replacing the hose between the pump and the control valve 0.6 0.6 0.6 081631A
Replacing a hose between the control valve and the solenoid valve block 0.6 0.6 0.6 081631B
RETURN PIPES 081635Replacing the return hose between the solenoid valve block and the hydraulic oil filter 0.5 0.5 0.5 081635A
Replacing the return hose between the control valve and the hydraulic oil filter 0.3 0.3 0.3 081635B
Replacing the return hose between the oil-cooler and the hydraulic oil filter 0.7 0.7 0.7 081635C
Replacing the return hose between the oil-cooler and the hydraulic reservoir 0.4 0.4 0.4 081635D
Replacing the hose of the hydraulic oil filter 0.5 0.5 0.5 081635E
Cre 9-88850 Issued 07-03
HYDRAULIC SYSTEM 8-2
TX13
0
TX14
0
TX17
0 MachineLocationJob Code
HYDRAULIC VALVESCONTROL VALVE 081643R & I of the control valve 2.3 2.3 2.3 081643AR & I of a section of the control valve 0.6 0.6 0.6 081643BOverhaul of the control valve (included washing, checking, reparation or replacement of any parts, if necessary)
3.2 3.2 3.2 081643C
SOLENOID VALVE BLOCK 081645R & I of the supply locking valve 0.9 0.9 0.9 0881645AR & I of the solenoid valve block for stabilizer and levelling cylinder 0.7 0.7 0.7 0881645B
HYDRAULIC CIRCUITLIFTING/COMPENSATION CIRCUIT 081653Replacing the hose (Port A) between the control valve and the telescopic arm 0.6 0.6 0.6 081653A
Replacing the hose (Port B) between the control valve and the telescopic arm 0.8 0.8 0.8 081653B
TELESCOPIC CIRCUIT 081654Replacing the hose (Port A) between the control valve and the telescopic arm 0.6 0.6 0.6 081654A
Replacing the hose (Port B) between the control valve and the telescopic arm 0.8 0.8 0.8 081654B
Replacing the hose of telescopic cylinder 0.5 0.5 0.5 081654CReplacing the hose of telescopic cylinder (option) *** *** 0.2 081654D
TILT CIRCUIT 081655Replacing the hose (Port A) between the control valve and the telescopic arm 0.6 0.6 0.6 081655A
Replacing the hose (Port B) between the control valve and the telescopic arm 0.8 0.8 0.8 081655B
Replacing the hose of tilt cylinder 0.3 0.3 0.3 081655CReplacing the intermediate hose of telescopic arm 0.5 0.5 2.6 081655DReplacing the intermediate hose of tilt cylinder and auxiliary functions *** *** 0.5 081655E
Cre 9-88850 Issued 07-03
HYDRAULIC SYSTEM 8-3
TX13
0
TX14
0
TX17
0 MachineLocationJob Code
PILOT CIRCUIT 081656Replacing the hose (one) between the manipulator and the intermediate plate 2.0 2.0 2.0 081656A
Replacing the hoses (all) between the manipulator and the intermediate plate 2.3 2.3 2.3 081656B
Replacing the hose (one) between the intermediate plate and the control valve 0.6 0.6 0.6 081656C
Replacing the hoses (all) between the intermediate plate and the control valve 0.9 0.9 0.9 081656D
Replacing the hose between the intermediate plate and the supply locking valve 0.6 0.6 0.6 081656E
Replacing the hose between the intermediate plate and the hydraulic reservoir 0.6 0.6 0.6 081656F
AUXILIARY CIRCUIT 081657Replacing the hose of control valve Port A 0.6 0.6 0.6 081657AReplacing the hose of control valve Port B 0.8 0.8 0.8 081657BReplacing the hose of auxiliary circuit in telescopic arm 0.5 0.5 2.6 081657C
HYDRAULIC CYLINDERS STABILIZER CYLINDERS 081661R & I of the stabilizer cylinder (right or left) 0.5 0.5 0.5 081661AOverhaul of the stabilizer cylinder (right or left) 1.8 1.8 1.8 081661B
AXLE LOCKING CYLINDERS 081662R & I of the levelling cylinder (front axle) 0.4 0.4 0.4 081662AOverhaul of the levelling cylinder (front axle) 1.8 1.8 1.8 081662BR & I of the axle locking cylinder (rear axle) 0.4 0.4 0.4 081662COverhaul of the axle locking cylinder (rear axle) 1.8 1.8 1.8 081662D
LIFTING/COMPENSATION CYLINDERS 081663R & I of the lift cylinder 5.0 5.0 5.0 081663AOverhaul of the lift cylinder 2.0 2.0 2.0 081663BR & I of the compensation cylinder 1.4 1.4 1.4 081663COverhaul of the compensation cylinder 1.8 1.8 1.8 081663D
TELESCOPIC CYLINDERS 081664R & I of the telescopic cylinder 2.3 2.3 3.0 081664AOverhaul of the telescopic cylinder 2.5 2.5 2.5 081664BR & I of the telescopic cylinder (option) *** *** 0.8 081664COverhaul of the telescopic cylinder (option) *** *** 2.0 081664D
TILT CYLINDER 081665R & I of the tilt cylinder 0.5 0.5 0.5 081665AOverhaul of the tilt cylinder 1.8 1.8 1.8 081665B
Cre 9-88850 Issued 07-03
HYDRAULIC SYSTEM 8-4
TX13
0
TX14
0
TX17
0 MachineLocationJob Code
HYDRAULIC OIL COOLERHYDRAULIC OIL COOLER 081681R & I of the hydraulic oil cooler 0.4 0.4 0.4 081681A
CONTROL LEVERHAND LEVER 081691R & I of the manipulator 0.6 0.6 0.6 081691AOverhaul of the manipulator 1.0 1.0 1.0 081691B
Cre 9-88850 Issued 07-03
CHASSIS/ATTACHMENTS 9-1
TX13
0
TX14
0
TX17
0 MachineLocationJob Code
MAINTENANCE xxxxxReplacing the heating block filter in the cab 0.5 0.5 0.5 090001B
MAIN CHASSIS FRAME 090111Replacing the main chassis frame 45.0 45.0 45.0 090111A
COUNTERWEIGHT 090117R & I of the ballast (one) 0.3 0.3 0.3 090117A
HOODS, PANELS AND PROTECTIVE DEVICESHOODS, SIDE PANELS AND SERVICE ACCESS POINTS 090131R & I of the rear grill assembly 0.1 0.1 0.1 090131AR & I of the tilting cowling, top 0.3 0.3 0.3 090131BR & I of the fixed cowling, bottom 0.4 0.4 0.4 090131C
FENDERS, STEPS AND LADDERS 090133R & I of the front fenders 0.6 0.6 0.6 090133AR & I of the rear fenders 0.6 0.6 0.6 090133B
PAINT AND ADHESIVE 090137Complete painting of the cab 6.0 6.0 6.0 090137AComplete painting of a front wheel rim 0.5 0.5 0.5 090137BComplete painting of a rear wheel rim 0.5 0.5 0.5 090137CComplete painting of the chassis frame 6.0 6.0 6.0 090137DComplete painting of the ballast (one) 1.1 1.1 1.1 090137EComplete painting of the radiator 0.5 0.5 0.5 090137F
CAB
090311R & I of the cab assembly 2.0 2.0 2.0 090311AR & I of the sun visor curtain 0.4 0.4 0.4 090311B
CAB DOORS AND WINDOWS 090313Replacing a hinge of the rear left panel 0.2 0.2 0.2 090313AR & I of a cab door 0.5 0.5 0.5 090313BReplacing a cab door seal 0.8 0.8 0.8 090313CReplacing the handle of the cab door 0.4 0.4 0.4 090313DReplacing the inside handle of the cab door 0.4 0.4 0.4 090313EReplacing the loosening lever of the cab door 0.7 0.7 0.7 090313FR & I of a inside door panel 0.2 0.2 0.2 090313GR & I of a outside door panel 0.3 0.3 0.3 090313HReplacing the door glass 0.6 0.6 0.6 090313IReplacing the cab windshield 1.0 1.0 1.0 090313JReplacing a upper glass in the cab 1.0 1.0 1.0 090313KReplacing a side glass in the cab 2.0 2.0 2.0 090313LReplacing a rear glass hinge in the cab 0.2 0.2 0.2 090313MReplacing the rear glass in the cab 1.0 1.0 1.0 090313NReplacing the locking device of the rear glass 0.2 0.2 0.2 090313OR & I of a rear-view mirror 0.2 0.2 0.2 090313P
CAB FRAME, ROOF AND CAB ATTACHMENTS
Cre 9-88850 Issued 07-03
CHASSIS/ATTACHMENTS 9-2
TX13
0
TX14
0
TX17
0 MachineLocationJob Code
HEATING AND DEFROSTING SYSTEM 090315Replacing the air ducts between the heater assembly and the air distributors 2.0 2.0 2.0 090315A
Replacing the heater regulating valve in the cab 0.2 0.2 0.2 090315BR & I of the heater assembly in the cab 3.8 3.8 3.8 090315C
090318R & I the oil brake tank guard 0.1 0.1 0.1 090318AR & I the upper covering 1.4 1.4 1.4 090318BR & I the lower covering 2.0 2.0 2.0 090318CR & I the steering cover 0.2 0.2 0.2 090318DR & I of the bellows 0.6 0.6 0.6 090318ER & I of the side covering 2.8 2.8 2.8 090318FR & I of the rear covering 0.5 0.5 0.5 090318G
INSULATION AND CAB CEILING 090319R & I of the front left panel 0.3 0.3 0.3 090319AR & I of the rear left panel 0.3 0.3 0.3 090319BR & I of the front guard 0.2 0.2 0.2 090319CR & I of the rear guard 0.2 0.2 0.2 090319DR & I of the cab roof panel 0.3 0.3 0.3 090319ER & I of the cab roof side panel 0.2 0.2 0.2 090319FR & I of the covering, right or left 0.4 0.4 0.4 090319G
SEATS AND SAFETY BELTSSEATS AND BRACKETS 090331R & I of the driver seat 0.3 0.3 0.3 090331AR & I of an armrest 0.2 0.2 0.2 090331B
SAFETY BELTS 090333Replacing the safety belt 0.2 0.2 0.2 090333A
STRUCTURAL COMPONENTSSTABILIZER LEGS AND PADS 091631R & I of the narrow stabilizers assembly (for replacement if necessary) 2.2 2.2 2.2 091631A
R & I of the large stabilizers assembly (for replacement if necessary) 2.2 2.2 2.2 091631B
TELESCOPIC ARM 091636R & I of the arm N°. 1 (included R & I of the quick hooker) 6.0 6.0 6.5 091636A
R & I of the arm N°. 2 3.9 3.9 4.0 091636BR & I of the arm N°. 3 3.9 3.9 4.0 091636CR & I of the arm N°. 4 3.9 3.9 4.0 091636DR & I of the telescopic arm assembly (included washing, checking and repairing of any parts, if necessary)
7.0 7.0 7.9 091636E
INSTALLATION OF OPERATOR’S CONSOLE TRIM, THE INSTRUMENT PANEL AND THE STEERING COLUMN
Cre 9-88850 Issued 07-03
top related