rock engineering practice & design -...
Post on 06-Feb-2018
226 Views
Preview:
TRANSCRIPT
Rock EngineeringRock EngineeringPractice & DesignPractice & Design
Lecture 11: Lecture 11: Excavation MethodsExcavation Methods
1 of 45 Erik Eberhardt – UBC Geological Engineering ISRM Edition
Author’s Note:Author’s Note:The lecture slides provided here are taken from the course “Geotechnical Engineering Practice”, which is part of the 4th year Geological Engineering program at the University of British Columbia (V C d ) Th k i i d (Vancouver, Canada). The course covers rock engineering and geotechnical design methodologies, building on those already taken by the students covering Introductory Rock Mechanics and Advanced Rock Mechanics Rock Mechanics.
Although the slides have been modified in part to add context, they of course are missing the detailed narrative that accompanies any l l d h h l lecture. It is also recognized that these lectures summarize, reproduce and build on the work of others for which gratitude is extended. Where possible, efforts have been made to acknowledge th v ri us s urc s ith list f r f r nc s b in pr vid d t th the various sources, with a list of references being provided at the end of each lecture.
Errors, omissions, comments, etc., can be forwarded to the
2 of 45 Erik Eberhardt – UBC Geological Engineering ISRM Edition
Errors, omissions, comments, etc., can be forwarded to the author at: erik@eos.ubc.ca
The Excavation ProcessThe Excavation ProcessIt is instructive to consider the fundamental objective of the excavation process – which is to remove rock material (either to create an opening or to obtain material for its inherent value). In order to remove part of a rock mass it is necessary to induce additional fracturing and rock mass, it is necessary to induce additional fracturing and fragmentation of the rock.
This introduces three critical aspects of excavation:
The peak strength of the rock must be exceeded.
p
The in situ block size distribution must be changed to the required fragment size distributiondistribution.
By what means should the required energy be introduced into the rock?
3 of 45 Erik Eberhardt – UBC Geological Engineering ISRM Edition
into the rock?
In SituIn Situ Block and Fragmentation DistributionBlock and Fragmentation DistributionRock is naturally fractured and consists of rock blocks of certain sizes. The fracturing of rock during excavation changes this natural block size changes this natural block size distribution to the fragment size distribution. The engineer can consider how best to move from one curve to the other in the excavation process.
4 of 45 Erik Eberhardt – UBC Geological Engineering ISRM Edition
Hudson & Harrison (1997)
Energy and Excavation ProcessEnergy and Excavation ProcessAlthough the objective during excavation is large-scale fragmentation, at the same time we wish to minimize any damage to the wall rock as this would work towards weakening the rock mass which may result in ground control problems Fragmentation and rock mass damage are both related control problems. Fragmentation and rock mass damage are both related to the amount of energy used and whether its applied instantaneously or continuously.
The tensile strength of rock is about 1/10th the compressive strength and the energy beneath h hl the stress-strain curve is roughly
its square. Therefore, breaking the rock in tension requires only 1/100th of the energy as that in
Hudson & Harrison (1997)
5 of 45 Erik Eberhardt – UBC Geological Engineering ISRM Edition
compression.
Energy and Excavation ProcessEnergy and Excavation Process
One objective in the excavation process may be to optimize the use of energy, i.e. the amount of energy required to remove a unit volume of rock (specific energy = J/m3). There are two fundamental ways of inputting energy into the rock for excavation:inputting energy into the rock for excavation:
Blasting: Energy is input in large h quantities over very short
durations (cyclical – drill then blast, drill then blast, etc.).
Machine Excavation: Energy is input in smaller quantities continuously.
6 of 45 Erik Eberhardt – UBC Geological Engineering ISRM Edition
Conventional Drill & BlastConventional Drill & Blast
The technique of rock breakage using explosives involves drilling blastholes by percussion or rotary-percussive means, loading the boreholes with explosives and then detonating the explosive in each explosives and then detonating the explosive in each hole in sequence according to the blast design.
The explosion generates a stress wave and significant gas pressure. Following the local fracturing at the local fracturing at the blasthole wall and the spalling of the free face, the subsequent gas pressure then provides the necessary energy to disaggregate the broken rock
7 of 45 Erik Eberhardt – UBC Geological Engineering ISRM Edition
rock. Hudson & Harrison (1997)
Conventional Drill & BlastConventional Drill & Blast
Drill Load
BlastSurvey Blast
V il
Survey
VentilateBolt
ScoopScale
8 of 45 Erik Eberhardt – UBC Geological Engineering ISRM Edition
Drill & Blast Drill & Blast -- DrillingDrilling
percussionhammer
thrustforce
rotationwaterflush(chip
9 of 45 Erik Eberhardt – UBC Geological Engineering ISRM Edition
( premoval)
Thuro (1997)
Drill & Blast Drill & Blast -- DrillingDrillingTh bit' bilit t t t th k ffi i tl d d th t t The bit's ability to penetrate the rock efficiently depends on the contact surface of the buttons, their shape and number, the bits' flushing characteristics and the brittleness, or drillability, of the rock.
Button Shape Characteristics Application
• "non aggressive" shape• minimum drilling rates
Rock with high UCS and high abrasivity
Sphericalminimum drilling rates
• low bit wear• excavation mainly by impact
• "aggressive" shape
and high abrasivity (e.g. quartzite, granite, gneiss, amphibolite)
Rock with mid UCS
Semi-Ballistic
gg p• moderate drilling rates• moderate bit wear• excavation mainly by shearing/cutting
and less abrasivity (e.g. slate, sandstone, limestone, weathered rock)
Conical(Ballistic)
• "very aggressive" shape• maximum drilling rates• high bit wear• excavation mainly by shearing/cutting
Rock with low UCS and low abrasivity (e.g. shale, weak sandstone, phyllite)
10 of 45 Erik Eberhardt – UBC Geological Engineering ISRM Edition
Thuro (1997)
Drill & Blast Drill & Blast –– Drill Bit ButtonsDrill Bit Buttons
l.(2
002)
nnin
ger
et a
l.
11 of 45 Erik Eberhardt – UBC Geological Engineering ISRM Edition
Plin
Drill & Blast Drill & Blast –– Blast Pattern DesignBlast Pattern DesignOne of the basic principles of designing the configuration and sequential detonation of blastholes in a one blast, is the presence of a free face parallel or sub-parallel to the blast holes, as detonation occurs. In some cases these free faces may already be present (benches in an open pit cases, these free faces may already be present (benches in an open pit mine), but in other cases may need to be created by the blast itself (a tunnel face).
Practical application of the free-face concept using one
12 of 45 Erik Eberhardt – UBC Geological Engineering ISRM Edition
free face concept using one form of the burn cut. Hudson & Harrison (1997)
Drill & Blast Drill & Blast –– Burn CutBurn CutTh t d i f bl t t t ith th fi t h l t b d t t d The correct design of a blast starts with the first hole to be detonated. In the case of a tunnel blast, the first requirement is to create a void into which rock broken by the blast can expand. This is generally achieved by a wedge or burn cut which is designed to create a clean void and to eject the g g jrock originally contained in this void clear of the tunnel face.
Burn cut designs using millisecond delays.
13 of 45 Erik Eberhardt – UBC Geological Engineering ISRM Edition
y
Drill & Blast Drill & Blast –– Blast Pattern DesignBlast Pattern Design
14 of 45 Erik Eberhardt – UBC Geological Engineering ISRM Edition
Specialized Blasting TechniquesSpecialized Blasting TechniquesD i bl ti th l i d t l di During blasting, the explosive damage may not only occur according to the blasting round design, but there may also be extra rock damage behind the excavation boundary. To minimize damage to the rock a pre split blast (surface excavation) or smooth wall blast rock, a pre-split blast (surface excavation) or smooth-wall blast (underground) may be used to create the final excavation surface.
Pre-split blast: First a series of small-diameter, parallel boreholes are is
on (1
997)
drilled along the plane of the required final excavation boundary (i.e. rock cut slope) ds
on &
Har
r
15 of 45 Erik Eberhardt – UBC Geological Engineering ISRM Edition
rock cut slope).
Hud
PrePre--Split & SmoothSplit & Smooth--Wall BlastingWall Blasting
The principle is then to tailor the explosive parameters such that detonation of the
l i i h i i i l explosives in these initial holes will primarily create a plane of intersecting holes through the coalescence of through the coalescence of several induced fractures.
The smooth-wall blast follows a similar process to the pre-split blast, except in the reverse order. First a rough opening is formed using a large bulk opening is formed using a large bulk blast, and then the smooth-wall blast follows along a series of closely spaced and lightly charged parallel holes.
16 of 45 Erik Eberhardt – UBC Geological Engineering ISRM Edition
Hudson & Harrison (1997)
PrePre--Split BlastingSplit BlastingWhen, subsequently, the main body of rock is blasted to form the cutting, the pre-split reflects the stress waves back into the rock being excavated and dissipates excess gas pressure, such that the bulk blast has little effect of the rock behind the pre-split plane blast has little effect of the rock behind the pre-split plane.
pre-split bl t d
normal bulk bl d
17 of 45 Erik Eberhardt – UBC Geological Engineering ISRM Edition
blasted blasted
Drill & Blast Drill & Blast –– ExplosivesExplosivesCommercial explosives are mixtures of chemical compounds in solid or liquid form. Detonation transforms the compounds into other products, mostly gaseous.
The following are the main criteria applied to select an explosive for a given type of blasting: available energy per unit weight
of explosive (i.e. strength)
density of the explosive
detonation velocity sensitivity (ease of ignition)
ti t reaction rate
temperature and pressure stability (chemical and storage)
18 of 45 Erik Eberhardt – UBC Geological Engineering ISRM Edition
y ( g )
Drill & Blast Drill & Blast –– ExplosivesExplosivesThe following are the more common explosives used in hard rock excavation:
dynamites (nitroglycerin made stable by dissolving it in an inert bulking agent – moderate bulk strength)bulking agent moderate bulk strength)
ANFO (Ammonium Nitrate & diesel Fuel Oil – low bulk strength)
slurries (water gels – high bulk strength for wet conditions)
emulsions
ANFO is the most prevalent explosive used in mining because it is the least expensive and the safest to transport and handle. ANFO type explosives are susceptible to water and
19 of 45 Erik Eberhardt – UBC Geological Engineering ISRM Edition
explosives are susceptible to water and, therefore, are not suitable for wet blastholes.
Drill & Blast Drill & Blast –– StemmingStemming“Stemming” materials (e.g. pea-sized gravel), are used to top-off the blastholes. The stemming material acts to provide confinement acts to provide confinement, preventing the explosive gases and energy from travelling (venting) up through the drill hole, and instead are
i d i hi h k contained within the rock mass.
Effects of poor
20 of 45 Erik Eberhardt – UBC Geological Engineering ISRM Edition
Effects of poor stemming.
Drill & Blast Drill & Blast –– Blasting Caps & DelaysBlasting Caps & Delays
A blasting cap is a small explosive device generally used to detonate a larger, more powerful explosive. Most blasting caps contain what is c ll d p im xpl si A p im xpl si is called a primary explosive. A primary explosive is a high explosive compound that will explode from flame, heat or shock.
Word to the wise: Do not crimp fuses to blasting caps using your teeth.
Few blasts are fired instantaneously. Instead, delays are used to sequence the blast giving better fragmentation, g g gmore efficient use of the explosive, reduced vibration, and better controlof the fly rock. Generally, delay detonators are produced in measures
21 of 45 Erik Eberhardt – UBC Geological Engineering ISRM Edition
detonators are produced in measures of milliseconds or seconds.
Drill & Blast Drill & Blast –– Fly RockFly RockFl k i t t t bl t d th i Fly rock is a constant concern to blasters and their co-workers. It can be controlled if proper preparation, blasting techniques and safety procedures are followed. Four of the major causes p jof excessive fly rock are:
• Geology conditions.• Inaccurate drilling and loading.g g• Poor hole design.• Poor pattern timing.
Incidents have been recorded where flyrock has travelled in excess of 1 km and resulted in significant damage, injury and/or death.
22 of 45 Erik Eberhardt – UBC Geological Engineering ISRM Edition
Drill & Blast Drill & Blast –– FragmentationFragmentation
How efficiently muck from a working tunnel or surface excavation can be removed is a function of the blast fragmentation. Broken rock by volume is usually 50% greater than the in situ material. In mining, both the ore nd t h t b m d t f f millin di p l S m t and waste has to be moved to surface for milling or disposal. Some waste
material can be used underground to backfill mined voids. In tunnelling, everything has to be removed and dumped in fills – or if the material is right, may be removed and used for road ballast or concrete aggregate g , y gg g(which can sometimes then be re-used in the tunnel itself).
23 of 45 Erik Eberhardt – UBC Geological Engineering ISRM Edition
Drill & Blast Drill & Blast –– SummarySummary
TNU
(199
5)
24 of 45 Erik Eberhardt – UBC Geological Engineering ISRM Edition
NT
Mechanical ExcavationMechanical Excavation
Tunnel Boring Machine (TBM)
25 of 45 Erik Eberhardt – UBC Geological Engineering ISRM Edition
Mechanical ExcavationMechanical ExcavationThere are two basic types of machine for underground excavation:
Partial face machines: use a Full face machines: use a rotating head Partial-face machines: use a cutting head on the end of a movable boom (that itself may be track mounted).
Full-face machines: use a rotating head armed with cutters, which fills the tunnel cross-section completely, and thus almost always excavates circular tunnels.
26 of 45 Erik Eberhardt – UBC Geological Engineering ISRM Edition
Mechanical ExcavationMechanical ExcavationP ti l f m hin Partial-face machines are cheaper, smaller and much more flexible in operation.p
cut
muck muck out
scoop
27 of 45 Erik Eberhardt – UBC Geological Engineering ISRM Edition
Mechanical ExcavationMechanical ExcavationFull-face machines – when used for relatively straight and long tunnels (>2 km) – permit high rates of advance in a smooth, automated construction operationconstruction operation.
muck out
scoop
out
cut
28 of 45 Erik Eberhardt – UBC Geological Engineering ISRM Edition
Mechanical ExcavationMechanical ExcavationThe advance rate at which the excavation proceeds is a function of the cutting rate and utilization factor (which is the amount of time that the machine is cutting rock). Factors contributing to low utilization rates are difficulties with ground support and steering the need to frequently difficulties with ground support and steering, the need to frequently replace cutters, blocked scoops, broken conveyors, etc.
The cutters may jam if the TBM i h d f d TBM is pushed forwards with too much force. Then they might scrape against the rock and become fl tt d id flattened on one side.
29 of 45 Erik Eberhardt – UBC Geological Engineering ISRM Edition
Broken conveyor
Mechanical Excavation Mechanical Excavation –– Tool WearTool WearDelays: When the tunnel boring machine is inside the tunnel the cutters Delays: When the tunnel boring machine is inside the tunnel, the cutters must be changed from the inside the cutting head.
30 of 45 Erik Eberhardt – UBC Geological Engineering ISRM Edition
Mechanics of Rock Cutting Mechanics of Rock Cutting –– Tool WearTool WearTh i i t f t l t b th t tt The primary impact of tool wear on costs can be so severe that cutter costs are often considered as a separate item in bid preparation. For TBM cutters, 1.5 hours are required for a single cutter change, and if several cutters are changed at one time, each may require 30-40 minutes. Even
uneven
g m , m y q mhigher downtimes can be expected with large water inflows, which make cutter change activities more difficult and time-consuming.
newunevenwear
normalwear
heavywear
31 of 45 Erik Eberhardt – UBC Geological Engineering ISRM Edition
Thuro & Plinninger (2003)
Mechanics of Rock CuttingMechanics of Rock CuttingD i th tti b th th t (F ) d t (F ) li d I During the cutting process, both thrust (Fn) and torque (Ft) are applied. In selecting the proper cutting tool, the engineer wishes to know how the tools should be configured on a machine cutting head, how to minimize the need to replace cutters, how to avoid damaging the cutter mounts, and p , m g g m ,how to minimize vibration.
son
(199
7)ds
on &
Har
ris
32 of 45 Erik Eberhardt – UBC Geological Engineering ISRM Edition
Hud
Mechanics of Rock CuttingMechanics of Rock CuttingC tti i l l i t f t il Cutting involves a complex mixture of tensile, shear and compressive modes of failure. With thrust, the cutting disc penetrates the rock and generates extensive crack propagation to the generates extens ve crack propagat on to the free surface. Further strain relief occurs as the disc edge rolls out of its cut, inducing further tensile cracking and slabbing at the rock surface.
rift
(199
8)U
-Anl
eggs
dr
33 of 45 Erik Eberhardt – UBC Geological Engineering ISRM Edition
NTN
U
TBM Excavation & DesignTBM Excavation & DesignThe two main factors that will stop tunnel boring machines are either the rock is too hard to cut or that the rock is too soft to sustain the the rock is too soft to sustain the reactionary force necessary to push the machine forward. TBM’s will operate within certain ranges f k d f bili d h of rock deformability and strength,
where the machine can be tailored to a specific range to achieve maximum efficiency (the risk being maximum efficiency (the risk being if rock conditions diverge from those the TBM is designed for) .
2000
)
Instability problems at the tunnel face, encountered during excavation of the 12.9km long Pinglin tunnel in &
Pel
izza
(2
34 of 45 Erik Eberhardt – UBC Geological Engineering ISRM Edition
g gTaiwan.
Barl
a
TBM Excavation & DesignTBM Excavation & Design
2000
)a
& Pe
lizza
(
35 of 45 Erik Eberhardt – UBC Geological Engineering ISRM Edition
Barl
a
TBM Excavation & DesignTBM Excavation & DesignSingle & Double Shield TBM’s – Single-shield TBM’s are cheaper and are the preferred machine for hard rock tunnelling. Double shielded TBMs are normally used in unstable geology (as they offer more worker protection), or where a high rate of advancement is required.
“Single” shield TBM
“Double” shield TBM
TBM
36 of 45 Erik Eberhardt – UBC Geological Engineering ISRM Edition
TBM Excavation & DesignTBM Excavation & DesignO & Cl d F Shi ld Wh th t l f d t i ti Open- & Closed-Face Shields – When the tunnel face does not require a continuous and pressure balanced support, the TBM is operated in ‘Open Mode’. The face is mechanically supported by the cuttinghead while the flood control doors regulate muck flow from the face to the cuttinghead chamber. The excavated muck is
idl t t d b th With l d f i l k d b lkh d rapidly extracted by the conveyor. With a closed-face, an airlock and bulkhead are used to allow the “excavation chamber” to be pressurized with compressed air to aid face support.
Open-face shields
Closed-face shields
37 of 45 Erik Eberhardt – UBC Geological Engineering ISRM Edition
TBM Excavation & DesignTBM Excavation & DesignEarth Pressure Balance (Closed-Face Shield) – This method provides continuous Earth Pressure Balance (Closed-Face Shield) – This method provides continuous support to the tunnel face by balancing earth pressure against machine thrust. As the cutterhead rotates and the shield advances, the excavated earth is mixed with foams in the cutterhead chamber to control its viscosity. The pressure is then adjusted by means of the rate of its extraction (by screw conveyor) to balance the adjusted by means of the rate of its extraction (by screw conveyor) to balance the pressure exerted by the ground at the tunnel face. This enables near surface tunnelling in bad ground conditions with minimal surface settlement.
clay foam injectory j
38 of 45 Erik Eberhardt – UBC Geological Engineering ISRM Edition
TBM Excavation & DesignTBM Excavation & Design
U S Army Corps of Engineers (1997)U.S. Army Corps of Engineers (1997)
39 of 45 Erik Eberhardt – UBC Geological Engineering ISRM Edition
TBM Excavation & DesignTBM Excavation & Design
U.S. Army Corps of Engineers (1997)
40 of 45 Erik Eberhardt – UBC Geological Engineering ISRM Edition
TBM Selection & Geological RiskTBM Selection & Geological RiskTh Y bú Q ib T l i i l f The Yacambú-Quibor Tunnel is a prime example of tunnelling blind – the geology was largely unfamiliar and unpredictable. With little previous experience, it was unknown how the rock would react, especially it was unknown how the rock would react, especially under the high stresses of the Andes.
Geology: Weak, tectonically sheared graphitic phyllites were encountered giving rise to serious squeezing problems, which without
1975: Excavation begins on the 24 km tunnel, for which the use of a full-face TBM is specified (for rapid excavation).
adequate support would result in complete closure of the tunnel.
1977: The weak phyllites fail to provide the TBM grippers with enough of a foundation to push off of. Supporting squeezing ground was another defeating problem.
h l d h d k d
ek (2
001)
1979: During a holiday shutdown, squeezing rock conditions were left unchecked, resulting in the converging ground effectively “swallowing” one of the TBMs.
1980’s: A decision is made to permit the tunnel to be
41 of 45 Erik Eberhardt – UBC Geological Engineering ISRM Edition
HoeMining out the remains of
the trapped TBM.
pexcavated by drill & blast. Recently completed, it took more than 33 years to tunnel the full 24 km.
TBM Excavation & DesignTBM Excavation & DesignTBM i ti th h TBM insertion through vertical shaft.
TBM gripper used to providereactionary force for forward thrust reactionary force for forward thrust by gripping onto sidewalls of tunnel.
TBM working platform for installing support (e g rock
42 of 45 Erik Eberhardt – UBC Geological Engineering ISRM Edition
installing support (e.g. rock bolts, meshing, shotcrete).
TBM Excavation & Design TBM Excavation & Design -- PrePre--Cast LiningsCast Linings
43 of 45 Erik Eberhardt – UBC Geological Engineering ISRM Edition
Tunnelling BreakthroughsTunnelling Breakthroughs
44 of 45 Erik Eberhardt – UBC Geological Engineering ISRM Edition
Lecture ReferencesLecture ReferencesBarla, G & Pelizza, S (2000). TBM Tunneling in difficult conditions. In GeoEng2000 - Proceedings ofthe International Conference on Geotechnical & Geological Engineering, Melbourne. TechnomicPublishing Company: Lancaster, pp. 329-354.
Hoek, E (2001). Big tunnels in bad rock (the Thirty-Sixth Karl Terzaghi Lecture). Journal ofGeotechnical and Geoenvironmental Engineering 127(9): 726-740.
Hudson, JA & Harrison, JP (1997). Engineering Rock Mechanics – An Introduction to the Principles .Elsevier Science: Oxford.
NTNU (1995) Tunnel: Blast Design Norwegian University of Science and Technology (NTNU):NTNU (1995). Tunnel: Blast Design. Norwegian University of Science and Technology (NTNU):Trondheim, Project Report 2A-95.
NTNU-Anleggsdrift (1998). Hard Rock Tunnel Boring: The Boring Process. Norwegian University ofScience and Technology (NTNU): Trondheim, Project Report 1F-98.
Plinninger, RJ, Spaun, G & Thuro, K (2003). Prediction and classification of tool wear in drill andblast tunnelling. In Proc., 9th Congress of the IAEG, Durban. CD-ROM, paper #395, pp. 2226-2236.
Thuro, K (1997). Drillability prediction: Geological influences in hard rock drill and blast tunnelling.Geologische Rundschau 86(2): 426-438.g ( )
Thuro, K & Plinninger, RJ (2003). Hard rock tunnel boring, cutting, drilling and blasting: Rockparameters for excavatability. In Proc., 10th ISRM Congress, Johannesburg. SAIMM: Johannesburg,pp. 1227-1234.
U S A C f E i (1997) E i i d D i T l d Sh ft i R k
45 of 45 Erik Eberhardt – UBC Geological Engineering ISRM Edition
U.S. Army Corps of Engineers (1997). Engineering and Design - Tunnels and Shafts in Rock.Publication EM 1110-2-2901.
top related