resistors in series introduction two types of current are readily available, direct current (dc) and...

Resistors in SeriesIntroduction

Two types of current are readily available, direct current (dc) and sinusoidal alternating current (ac)

We will first consider direct current (dc)

Insert Fig 5.1

Introducing the basic current flow of an electric circuit.

Defining the direction of conventional flow for single-source dc circuits.

Defining the polarity resulting from a conventional current I through a resistive element.

Resistors in series.

Schematic representation for a dc series circuit

Example of five resistors in series.

Series ResistorsThe total resistance of a series configuration

is the sum of the resistance levels.

The more resistors we add in series, the greater the resistance (no matter what their value).

NT RRRRRR ...4321

Resistance “seen” at the terminals of a series circuit.

Total Series Resistance

• The total resistance of a series circuit is equal to the sum of the resistances of each individual series resistor

Series connection of resistors.

Using an ohmmeter to measure the total resistance of a series circuit.

Two series combinations of the same elements with the same total resistance.

Series connection of resistors

Series combination of resistors

Series Resistors

• When series resistors have the same value,

• Where N = the number of resistors in the string.• The total series resistance is found by multiplying

the value of the same resistor times the number of resistors

NRRT

Series connection of four resistors of the same value

Four 2.2Kohms resistors

Resistors in Series

• A series circuit provides only one path for current between two points so that the current is the same through each series resistor

Current in a Series Circuit

• The current is the same through all points in a series circuit

• The current through each resistor in a series circuit is the same as the current through all the other resistors that are in series with it

• Current entering any point in a series circuit is the same as the current leaving that point

Current entering any point in a series circuit is the same as the current leaving that point.

Current is the same at all points in a series circuit.

Series Circuits

• Total resistance (RT) is all the source “sees.”

• Once RT is known, the current drawn from the source can be determined using Ohm’s law:

• Since E is fixed, the magnitude of the source current will be totally dependent on the magnitude of RT

Ts R

EI

Ohm’s Law in Series Circuits

• Current through one of the series resistors is the same as the current through each of the other resistors and is the total current

• If you know the total voltage and the total resistance, you can determine the total current by using:

• IT = VT/RT

Measuring the current throughout the series circuit

Find RT then find IS

Find Current in circuit ?

Find the voltage of the Source ?

Find the voltage of the Source

Ohm’s Law in Series Circuits

• Current through one of the series resistors is the same as the current through each of the other resistors and is the total current

• If you know the voltage drop across one of the series resistors, you can determine the current by using: I = VR/R

NotationSingle-subscript notation

The single-subscript notation Va specifies the voltage at point a with respect to ground (zero volts). If the voltage is less than zero volts, a negative sign must be associated with the magnitude of Va .

NotationDouble-subscript notation

• Because voltage is an “across” variable and exists between two points, the double-subscript notation defines differences in potential.

• The double-subscript notation Vab specifies point a as the higher potential. If this is not the case, a negative sign must be associated with the magnitude of Vab .

• The voltage Vab is the voltage at point (a) with respect to point (b).

Inserting the polarities across a resistor as determined by the direction of the current

Ohm’s Law in Series Circuits

• If you know the total current, you can find the voltage drop across any of the series resistors by using: VR = ITR

• The polarity of a voltage drop across a resistor is positive at the end of the resistor that is closest to the positive terminal of the voltage source

• The resistor current is in a direction from the positive end of the resistor to the negative end

Voltage in a Series dc circuit to be analyzed

Using voltmeters to measure the voltages across the resistors

Series circuit to be investigated

Series circuit to be analyzed

The source voltage appears across the open series resistor

Voltage Sources in Series

• When two or more voltage sources are in series, the total voltage is equal to the the algebraic sum (including polarities of the sources) of the individual source voltages

Reducing series dc voltage sources to a single source.

Series connection of dc supplies: (a) four 1.5 V batteries in series to establish a terminal voltage of 6 V; (b) incorrect connections for two series dc supplies; (c) correct connection of two series supplies to establish 60 V at the output terminals.

Kirchhoff’s Voltage LawThe applied voltage of a series circuit equals the sum of

the voltage drops across the series elements:

The sum of the rises around a closed loop must equal the sum of the drops.

The application of Kirchhoff’s voltage law need not follow a path that includes current-carrying elements.

When applying Kirchhoff’s voltage law, be sure to concentrate on the polarities of the voltage rise or drop rather than on the type of element.

Do not treat a voltage drop across a resistive element differently from a voltage drop across a source.

dropsrises VV

Kirchhoff’s Voltage Law

• Kirchhoff’s voltage law (KVL) states that the algebraic sum of the potential rises and drops around a closed loop (or path) is zero.

Kirchhoff’s Voltage Law

• The algebraic sum of all the voltage drops around a single closed loop in a circuit is equal to the total source voltage in that loop

VS = V1 + V2 + V3 + … + Vn

Applying Kirchhoff’s voltage law to a series dc circuit.

Another Way to state Kirchhoff’s Voltage Law

• The algebraic sum of all voltages (both sources and drops) around a closed path is zero

VS - V1 - V2 - V3 - … - Vn = 0

Illustration of a verification of Kirchhoff’s voltage law.

Sum of n voltage drops equals the source voltage.

Voltage Dividers

• Since each resistor has the same current, the voltage drops are proportional to the resistance values

The voltage divider as a bias circuit for a transistor amplifier.

Voltage-Divider Formula

• The voltage drop Vx across any resistor or combination of resistors in a series circuit is equal to the ratio of that resistance value Rx to the total resistance RT, multiplied by the source voltage VS

Vx = (Rx/RT)VS

Potentiometer as an Adjustable Voltage Divider

• The potentiometer shown below is equivalent to a two-resistor voltage divider that can be manually adjusted

• The two resistors are between terminals 1 & 3 and 2 & 3

Adjusting the voltage divider.

A voltage divider used for volume control.

A potentiometer voltage divider used as an automotive fuel-level sensor.

Example of a two-resistor voltage divider.

A five-resistor voltage divider.

Circuit Ground

• Voltage is relative• The voltage at one point in a circuit is always

measured relative to another point• This reference point in a circuit is usually the

ground point

Measuring Voltages with Respect to Ground

• When voltages are measured with respect to ground in a circuit, one meter lead is connected to the circuit ground, and the other to the point at which the voltage is to be measured

Simple illustration of circuit ground.

Measuring a voltage with respect to negative ground.

.

Measuring Voltages with Respect to Ground

Measuring voltages at several points in a circuit with respect to ground

Series circuit (without a short) with correct voltages marked.

Measuring Voltage Across an Ungrounded Resistor

• Voltage can normally (as long as the meter is isolated from the power line ground) be measured across a resistor even though neither side of the resistor is connected to circuit ground

• The reading will be the voltage drop across the resistor

Measuring voltage directly across a resistor.

Open Circuit

• The most common failure in a series circuit is an open

• When an open occurs in a series circuit, all of the source voltage appears across the open

The source voltage appears across the open series resistor.

Ohm’s Law in Series Circuits

• An open in a series circuit prevents current; and, there is zero voltage drop across each series resistor

• The total voltage appears across the points between which there is an open

An open in a circuit prevents current.

Troubleshooting a series circuit for an open using half-splitting.

Short Circuit

• When there is a short, a portion of the series resistance is bypassed, thus reducing the total resistance

• A short in a series circuit results in more current than normal through the circuit

• The voltage across a shorted series component (or circuit) is 0 volts

A Short in a Series Circuit

Example of shorts on a PC board.

Power in a Series Circuit

• The total amount of power in a series resistive circuit is equal to the sum of the powers in each resistor in series

PT = P1 + P2 + P3 + . . . + Pn

Power Distribution in a Series Circuit

The power applied by the dc supply must equal that dissipated by the resistive elements.

NRRRE PPPP ...21

Power in a Resistor

• The amount of power in a resistor is important because the power rating of the resistor must be high enough to handle the expected power in the circuit

Series circuit to be investigated for Power

Identifying Parallel Circuits

• If there is more than one current path (branch) between two separate points, and if the voltage between those two points also appears across each of the branches, then there is a parallel circuit between those two points

Resistors in Parallel

• Each current path is called a branch• A parallel circuit is one that has more than one

branch

Voltage in Parallel Circuits

• The voltage across any given branch of a parallel circuit is equal to the voltage across each of the other branches in parallel

Voltage across parallel branches is the same.

Kirchhoff’s current law: The current into a node equals the current out of that node.

Generalized Circuit Node Illustrating KCL

Total Parallel Resistance

• When resistors are connected in parallel, the total resistance of the circuit decreases

• The total resistance of a parallel circuit is always less than the value of the smallest resistor

Parallel Resistors

For parallel elements, the total conductance is the sum of the individual conductance values.

As the number of resistors in parallel increases, the input current level will increase for the same applied

voltage.

NT GGGGG ...321

Parallel ResistorsFor resistors in parallel, the total resistance is

determined from

Note that the equation is for the reciprocal of RT rather than for RT.

Once the right side of the equation has been determined, it is necessary to divide the result into 1 to determine the total resistance

Parallel Resistors

The total resistance of any number of parallel resistors can be determined using

The total resistance of parallel resistors is always less than the value of the smallest resistor.

N

T

RRRR

R1

...1111

321

Connecting resistors in parallel reduces total resistance and increases total current.

Circuit with n resistors in parallel.

Notation for Parallel Resistors

• To indicate 5 resistors, all in parallel, we would write:

R1||R2||R3||R4||R5

Illustration of a verification of Kirchhoff’s current law.

Total current divides between the two branches.

Generalized Circuit Node Illustrating KCL

Kirchhoff’s Current Law (KCL)

• The sum of the currents into a node (total current in) is equal to the sum of the currents out of that node (total current out)

IIN(1) + IIN(2) + . . . + IIN(n) = IOUT(1) + IOUT(2) +

. . . +IOUT(m)

Kirchhoff’s Current Law

• Kirchhoff’s current Law (KCL) can be stated another way:

The algebraic sum of all the currents entering and leaving a junction is equal to zero

FIGURE 5-18

Two-node configuration

Four-node configuration

.

Total Parallel Resistance

• When resistors are connected in parallel, the total resistance of the circuit decreases

• The total resistance of a parallel circuit is always less than the value of the smallest resistor

Formula for Total Parallel Resistance

1/RT = 1/R1 + 1/R2 + 1/R3 + . . . + 1/Rn

Parallel Resistors

For equal resistors in parallel:

Where N = the number of parallel resistors.

Two Resistors in Parallel

• The total resistance for two resistors in parallel is equal to the product of the two resistors divided by the sum of the two resistors

RT = R1R2/(R1 + R2)

Current Divider RuleThe current divider rule (CDR) is used to find the

current through a resistor in a parallel circuit.General points:

For two parallel elements of equal value, the current will divide equally.

For parallel elements with different values, the smaller the resistance, the greater the share of input current.

For parallel elements of different values, the current will split with a ratio equal to the inverse of their resistor values.

Current Divider Rule

Tx

Tx I

R

RI

General Current-Divider Formula

• The current (Ix) through any branch equals the total parallel resistance (RT) divided by the resistance (Rx) of that branch, and then multiplied by the total current (IT) into the junction of the parallel branches

Ix = (RT/Rx)IT

Notation for Parallel Resistors

• To indicate 5 resistors, all in parallel, we would write:

R1||R2||R3||R4||R5

Application of a Parallel Circuit

• One advantage of a parallel circuit over a series circuit is that when one branch opens, the other branches are not affected

Current Dividers

• A parallel circuit acts as a current divider because the current entering the junction of parallel branches “divides” up into several individual branch currents

Current Dividers

• The total current divides among parallel resistors into currents with values inversely proportional to the resistance values

FIGURE 5-53

FIGURE 5-51 A 10 mA meter.

FIGURE 5-52 A milliammeter with three ranges.

General Current-Divider Formula

• The current (Ix) through any branch equals the total parallel resistance (RT) divided by the resistance (Rx) of that branch, and then multiplied by the total current (IT) into the junction of the parallel branches

Ix = (RT/Rx)IT

Open Branches

• When a parallel resistor opens, IT is always less than its normal value

• Once IT and the voltage across the branches are known, a few calculations will determine the open resistor when all the resistors are of different values

Open Branches

• When an open circuit occurs in a parallel branch, the total resistance increases, the total current decreases, and the same current continues through each of the remaining parallel paths

When a lamp filament opens, total current decreases by the amount of current in the lamp that opened. The other branch currents

remain unchanged.

All parallel branches (open or not) have the same voltage.

Power in Parallel Circuits

• Total power in a parallel circuit is found by adding up the powers of all the individual resistors, the same as for series circuits

PT = P1 + P2 + P3 + . . . + Pn

Power flow in a dc parallel network.

When a lamp filament opens, total current decreases by the amount of current in the lamp that opened. The other branch currents remain unchanged.

All parallel branches (open or not) have the same voltage

Voltmeter Loading EffectsVoltmeters are always placed across an element

to measure the potential difference.The resistance of parallel resistors will always be less

than the resistance of the smallest resistor.A DMM has internal resistance which may alter the

resistance of the network under test.The loading of a network by the insertion of a meter is

not to be taken lightly, especially if accuracy is a primary consideration.

Voltmeter Loading Effects

A good practice is to always check the meter resistance against the resistive elements of the network before making a measurement.

Most DMMs have internal resistance levels in excess of 10 MW on all voltage scales.

The internal resistance of a VOM depends on the scale chosen.

Internal resistance is determined by multiplying the maximum voltage of the scale setting by the ohm/volt ( / V) rating of the meter, normally found at the bottom of the face of the meter.

Voltmeter loading.

Applications

Car systemThe electrical system on a car is essentially a parallel

system.

Parallel computer bus connectionsThe bus connectors are connected in parallel with

common connections to the power supply, address and data buses, control signals, and ground.

Expanded view of an automobile’s electrical system.

Application of a Parallel Circuit

• One advantage of a parallel circuit over a series circuit is that when one branch opens, the other branches are not affected

Applications

House wiringExcept in some very special circumstances the basic

wiring of a house is done in a parallel configuration.

Each parallel branch, however, can have a combination of parallel and series elements.

Each branch receives a full 120 V or 208 V, with the current determined by the applied load.

Application of a Parallel Circuit

• All lights and appliances in a home are wired in parallel

• The switches are located in series with the lights