residential - fantech trade
Post on 13-Nov-2021
3 Views
Preview:
TRANSCRIPT
© FANTECH TRADE 2018
//
RE
SID
EN
TIA
L R
AN
GE
9
RESIDENTIAL
Create a comfortable, healthy home with a complete ventilation system. Steam in the
bathroom and kitchen can lead to troublesome mold and moisture damage.
Our complete high quality products and ventilation solutions will keep the air in your
home fresh and healthy. From wall, ceiling or in-line fans to heat transfer kits, we have a
solution for all your residential ventilation needs.
FRESH AIR FOR THE HOME.
10 © FANTECH TRADE 2018
RE
SID
EN
TIA
L R
AN
GE
//
DOM EDMSILENT DESIGN
SILENT HCM STYLVENTRAPID
RESPONSEMINITUBE PROVENT TD SILENT
Ezifit Thru Wall
Ezifit In-Wall
Ezifit Thru Roof
APPLICATIONROOM
VOLUMEWALL
MOUNTEDWALL
MOUNTED WALL
MOUNTED WALL
MOUNTED WINDOW
MOUNTED
WALL OR WINDOW
MOUNTED
CEILING MOUNTED
IN-LINE DUCT MOUNTED
IN-LINE DUCT MOUNTED
IN-LINE DUCT MOUNTED
EXT. WALL MOUNTED
EXT. WALL MOUNTED
ROOF MOUNTED
6 - 10 AIR CHANGES PER HOUR
TOILETS
LAUNDRIES (NO DRYER)
STOREROOMS
CLASSROOMS
OFFICES
APARTMENTS
HOTELS
SITE SHEDS
SUB FLOOR VENTILATION
RESTAURANTS (SEATED AREA)
5m3 DOM-100C EDM-300C SILDES100 SILENT100 HCM-150N HV-150AERESPF150
+ RESPG150SQWHMTP132 RIL-100 TD-250.. EWE154 EIE150 ECE154..
10m3 DOM-100C EDM-300C SILDES100 SILENT100 HCM-150N HV-150AERESPF150
+ RESPG150SQWHMTP132 RIL-100 TD-250.. EWE154 EIE150 ECE154..
15m3 DOM-125C EDM-300C SILDES200 SILENT100 HCM-150N HV-150AERESPF150
+ RESPG150SQWHMTP132 RIL-100 TD-250.. EWE154 EIE150 ECE154..
20m3 DOM-125C EDM-300C SILDES200 SILENT125 HCM-150N HV-150AERESPF150
+ RESPG150SQWHMTP132 RIL-100 TD-250..
EWE154 (9)EWE152
EIE150 ECE154..
30m3 DOM-150C EDM-300C SILDES300 SILENT150 HCM-180NHV-150AE HV-230AE
RESPF150 + RESPG150SQWH
MTP132 RIL-125 TD-350.. EWE152 EIE150 (9)ECE154.. (7)
ECE152..
40m3 – – – – HCM-180N HV-230AERESPF150
+ RESPG150SQWH– RIL-150.. TD-500.. EWE152 (8) EIE150 (6) ECE152.. (8)
11 - 20 AIR CHANGES PER HOUR
ENSUITES
BATHROOMS
SPA BATHROOMS
LAUNDRIES (WITH DRYER)
KITCHENS
5m3 DOM-100C EDM-300C SILDES100 SILENT100 HCM-150N HV-150AERESPF150
+ RESPG150SQWHMTP132 RIL-100 TD-250.. EWE154 EIE150 ECE154..
10m3 DOM-125C EDM-300C SILDES200 SILENT125 HCM-150N HV-150AERESPF150
+ RESPG150SQWHMTP132 RIL-100 TD-250..
EWE154 (18)EWE152
EIE150 ECE154..
20m3 DOM-150C EDM-300C SILDES300 SILENT150 HCM-180N HV-230AERESPF150
+ RESPG150SQWH–
RIL-125 RIL-150..
TD-350.. EWE152 EIE150 (13) ECE152.. (17)
30m3 – – – – HCM-225N HV-230AE – – RIL-200.. TD-500.. EWE152 (11) – ECE204..
40m3 – – – – HCM-225N (16)HV-230AE (15)
HV-300AE– – RIL-200.. TD-800.. – – ECE204.. (17)
50m3 – – – – – HV-300AE – –Call Fantech Trade
for suitable fansTD-1300.. – –
Call Fantech Trade for suitable fans
1 2 3Select your required application from the left hand column.
eg. Spa Bathroom (11-20 air changes per hour)
Calculate the volume of the room in cubic metres (m3) by multiplying the length x width x height.
eg. 3.2m x 3.2m x 2.4m = 24.58m3 (therefore select a room volume of 30m3)
Follow the row across and select one of the fans available which suits your mounting requirements, using the pictures and headings as a guide.
eg. Require a Roof Mounted Fan along the 11-20 air changes per hour with 30m3 air volume row (therefore select an ECE204)
HOW TO USE THE PRODUCT SELECTION CHART
PRODUCT SELECTION CHART
11© FANTECH TRADE 2018
//
RE
SID
EN
TIA
L R
AN
GE
DOM EDMSILENT DESIGN
SILENT HCM STYLVENTRAPID
RESPONSEMINITUBE PROVENT TD SILENT
Ezifit Thru Wall
Ezifit In-Wall
Ezifit Thru Roof
APPLICATIONROOM
VOLUMEWALL
MOUNTEDWALL
MOUNTED WALL
MOUNTED WALL
MOUNTED WINDOW
MOUNTED
WALL OR WINDOW
MOUNTED
CEILING MOUNTED
IN-LINE DUCT MOUNTED
IN-LINE DUCT MOUNTED
IN-LINE DUCT MOUNTED
EXT. WALL MOUNTED
EXT. WALL MOUNTED
ROOF MOUNTED
6 - 10 AIR CHANGES PER HOUR
TOILETS
LAUNDRIES (NO DRYER)
STOREROOMS
CLASSROOMS
OFFICES
APARTMENTS
HOTELS
SITE SHEDS
SUB FLOOR VENTILATION
RESTAURANTS (SEATED AREA)
5m3 DOM-100C EDM-300C SILDES100 SILENT100 HCM-150N HV-150AERESPF150
+ RESPG150SQWHMTP132 RIL-100 TD-250.. EWE154 EIE150 ECE154..
10m3 DOM-100C EDM-300C SILDES100 SILENT100 HCM-150N HV-150AERESPF150
+ RESPG150SQWHMTP132 RIL-100 TD-250.. EWE154 EIE150 ECE154..
15m3 DOM-125C EDM-300C SILDES200 SILENT100 HCM-150N HV-150AERESPF150
+ RESPG150SQWHMTP132 RIL-100 TD-250.. EWE154 EIE150 ECE154..
20m3 DOM-125C EDM-300C SILDES200 SILENT125 HCM-150N HV-150AERESPF150
+ RESPG150SQWHMTP132 RIL-100 TD-250..
EWE154 (9)EWE152
EIE150 ECE154..
30m3 DOM-150C EDM-300C SILDES300 SILENT150 HCM-180NHV-150AE HV-230AE
RESPF150 + RESPG150SQWH
MTP132 RIL-125 TD-350.. EWE152 EIE150 (9)ECE154.. (7)
ECE152..
40m3 – – – – HCM-180N HV-230AERESPF150
+ RESPG150SQWH– RIL-150.. TD-500.. EWE152 (8) EIE150 (6) ECE152.. (8)
11 - 20 AIR CHANGES PER HOUR
ENSUITES
BATHROOMS
SPA BATHROOMS
LAUNDRIES (WITH DRYER)
KITCHENS
5m3 DOM-100C EDM-300C SILDES100 SILENT100 HCM-150N HV-150AERESPF150
+ RESPG150SQWHMTP132 RIL-100 TD-250.. EWE154 EIE150 ECE154..
10m3 DOM-125C EDM-300C SILDES200 SILENT125 HCM-150N HV-150AERESPF150
+ RESPG150SQWHMTP132 RIL-100 TD-250..
EWE154 (18)EWE152
EIE150 ECE154..
20m3 DOM-150C EDM-300C SILDES300 SILENT150 HCM-180N HV-230AERESPF150
+ RESPG150SQWH–
RIL-125 RIL-150..
TD-350.. EWE152 EIE150 (13) ECE152.. (17)
30m3 – – – – HCM-225N HV-230AE – – RIL-200.. TD-500.. EWE152 (11) – ECE204..
40m3 – – – – HCM-225N (16)HV-230AE (15)
HV-300AE– – RIL-200.. TD-800.. – – ECE204.. (17)
50m3 – – – – – HV-300AE – –Call Fantech Trade
for suitable fansTD-1300.. – –
Call Fantech Trade for suitable fans
All selections are based on installed fan performance and maximum air change rate (ie. 10 or 20). Figures in brackets (eg. (8)), show actual air change rate if it is less than the maximum.
Selections for Wall Mounted fans are based on the fan’s optimal performance using 230mm length of wall tube.
Selections for Ezifit range fans (EIE, EWE and ECE) and In-Line Duct Mounted fans are based on the fan’s optimal performance using 6m of duct. All flexible duct must be taught and straight. Longer duct runs may be possible. Please contact Fantech Trade for specific requirements. Selections for the Ezifit In-Wall (EIE) are based on the unit being wired in medium speed as standard.
NOTES ON SELECTION CRITERIA
PRODUCT SELECTION CHART
12 © FANTECH TRADE 2018
RE
SID
EN
TIA
L R
AN
GE
//A
PE
X A
IR S
CIE
NC
E
THE ART OF ENGINEERING A SYSTEM THAT REDEFINES VENTILATION PERFORMANCEFan engineering is in our DNA. Fantech have always been committed to constantly improving, innovating and leading the ventilation industry. Our scope of work has included fans fit for global mining facilities, defense force ships and some of the most iconic landmark buildings.
We engineer fans to be the most energy efficient and best performing products on the market, fans we can be proud of. Rigorous, accurate testing takes place in the world’s most sophisticated facilities, resulting in a market leading product that will provide ongoing reliable performance.
The Fantech Trade team have fully embraced this experience and technical expertise to develop fans ideal for the home or business.
As a leader in the air movement and ventilation industry, Fantech Trade have created a new benchmark for fans which are suitable for bathrooms, ensuites, kitchens and toilets. We believe in creating the most reliable ventilation products that perform to the highest standard and include intuitive features for easy installation. Apex Air Science means that every aspect of the fan has been designed, developed and tested by fan engineers with careful attention to every detail.
Apex Air Science is a fully optimised system that includes an aerodynamic housing and inlet cone, advanced impeller design and powerful long lasting motor technology for maximum air flow performance. Look for the Apex Air Science icon on our products to experience it for yourself.
14 © FANTECH TRADE 2018
RE
SID
EN
TIA
L R
AN
GE
//W
AL
L M
OU
NT
ED
FA
NS Aerodynamic Design
The front grille, impeller and guide vanes have been aerodynamically engineered to allow air to flow through the fan with the least possible resistance. This results in powerful performance matched with smooth and quiet operation.
Optimised ImpellersOptimal number of fan blades have been placed at specific angles to achieve maximum air flow and efficiency.
Guide Vanes As StandardAir passes over the optimised impeller and is smoothed out by angled guide vanes at the rear of the fan. Smooth air then leaves the fan with the lowest resistance possible.
Long Life MotorThe fan’s sealed for life ball bearings guarantee an extra long life span matched with high speed operation and performance. The motor is rated to last more than 30,000 hours (some traditional fans last only 3,000 hours).
Low Energy ConsumptionOur energy efficient motor makes our fan up to 50% more efficient than a traditional AC domestic fan. The fan is fitted with an air flow operated, silent membrane shutter which uses no energy to operate.
Ultra QuietThe motor is sandwiched between two elastic blocks which absorb vibrations, surface and motor noise.
Built To LastWe know this fan has been built correctly with only quality components. This means we can offer a groundbreaking 5 year warranty.
A I R S C I E N C E
15© FANTECH TRADE 2018
//
RE
SID
EN
TIA
L R
AN
GE
The Silent series exhaust fans are designed to solve
ventilation problems in bathrooms, ensuites and toilets.
They feature an advanced vibration absorbing design that
enables them to run quietly, while the high performance
motor and impeller exhausts air quickly and efficiently.
• Quiet operation due to its noise and vibration
absorbing design.
• Powerful air flow performance.
• Low loss foil backdraft damper is standard on
all models.
• Internal thermal motor cut out protection.
• 220-240V, single-phase, 50Hz supply.
ACCESSORIES
• Fan Controllers.
• External Grilles.
• Flexible Duct - Fire Rated AS/NZS 4254.
• Wall Tubes.
SILENTWALL MOUNTED FAN
IP45
Air Flow
MODEL NO.DUCT SIZE A B CØ D E
SILENT-100... 100 158 109 99 79 25
SILENT-125... 125 180 119 118 80 30
SILENT-150... 150 214 149 147 95 35
All dimensions in mm
MODEL NO.M3/HR†
L/SEC†
FAN SPEED RPM
AVG.dB(A) @ 3M
WATTS VOLTSIP
RATING
SILENT-100S-W 95 26 2400 27 8 230 IP45
SILENT-100T-W 95 26 2400 27 8 230 IP45
SILENT-100HT-W 95 26 2400 27 8 230 IP45
SILENT-125S-W 175 48 2350 33 16 230 IP45
SILENT-125T-W 175 48 2350 33 16 230 IP45
SILENT-125HT-W 175 48 2350 33 16 230 IP45
SILENT-150S-W 280 78 1700 32 29 230 IP45
SILENT-150T-W 280 78 1700 32 29 230 IP45
SILENT-150HT-W 280 78 1700 32 29 230 IP45
... S-W models include backdraft damper
... T-W models include backdraft damper and run-on timer
... HT-W models include backdraft damper, run-on timer and humidistat
† Air flow without duct and fittings
WALL MOUNTED FANS
See page 109 for performance curves.
16 © FANTECH TRADE 2018
RE
SID
EN
TIA
L R
AN
GE
//Air Flow
The Silent Design Series exhaust fans bring style
and elegance to the engineering brilliance of the
Silent wall fan range. They feature an advanced
vibration absorbing design to ensure quiet operation
and powerful air flow performance.
• Quiet operation due to its noise and vibration
absorbing design.
• Comes with 4 interchangeable colour bars to
match room décor.
• Low loss foil backdraft damper is standard on
all models.
• 1-30 minute adjustable run-on timer and adjustable
humidistat are available on selected models.
• Internal thermal motor cut out protection.
• 220-240V, single-phase, 50Hz supply.
ACCESSORIES
• External Grilles.
• Flexible Duct - Fire Rated AS/NZS 4254.
• Wall Tubes.
• Fan Controllers.
MODEL NO.DUCT SIZE A B CØ D E F
SILDES100.. 100 188 130 99 85 79 45
SILDES200.. 125 210 145 116 89 80 56
SILDES300.. 150 247 179 146 112 95 67
SILENT DESIGNWALL MOUNTED FAN
IP45
All dimensions in mm
WALL MOUNTED FANS
See page 109 for performance curves.
17© FANTECH TRADE 2018
//
RE
SID
EN
TIA
L R
AN
GE
COLOURS
To complement room fixtures all
models are available in white and
silver finish as standard. The Silent
Design range also comes in an
additional 9 colours as a special
order. Please allow 18 weeks
delivery from date of order for the
additional colours.
.. For complete model add Nom. flow rate m³/hr
† Air flow without duct and fittings* Add ‘CZ, ‘CRZ’, or ‘CHZ’ into fan model number as per features table
MODEL NO. SILDES
BACKDRAFT DAMPER RUN-ON TIMER HUMIDISTAT FINISH COLOUR
..CZ3C-W Yes No No White
..CZ3C-S Yes No No Silver
..CRZ3C-W Yes Yes No White
..CRZ3C-S Yes Yes No Silver
..CHZ3C-W Yes Yes Yes White
..CHZ3C-S Yes Yes Yes Silver
MODEL NO. PANEL COLOUR M3/HR† L/SEC† FAN SPEED RPMAVG. dB(A)
@ 3MWATTS VOLTS IP RATING
SILDES100*3C-W White85 23 2100 27 8 230 IP45
SILDES100*3C-S Silver
SILDES200*3C-W White 175 48 2450 35 16 230 IP45
SILDES200*3C-S Silver
SILDES300*3C-W White 300 83 2150 42 22 230 IP45
SILDES300*3C-S Silver
White
Silver
INTERCHANGEABLE COLOUR BARS
The Silent Design can be customised with an
interchangeable bar so your fan can blend in
with any setting. Four colours to match the
décor of the room: blue, red, green and yellow.
WALL MOUNTED FANS
18 © FANTECH TRADE 2018
RE
SID
EN
TIA
L R
AN
GE
//
DOM
MODEL NO.DUCT SIZE
A B C D E F G H
DOM-100C 100 158 168 99 82 20 - - -
DOM-125C 125 180 190 118 102 26 - - -
DOM-150C 150 200 200 152 129 - 104 51 148
The Dom Series is a range of low cost, high performing
and European made extract fans. They are reliable and well
suited for domestic applications such as bathrooms, toilets
and laundries.
• Made from tough injection moulded plastic.
• Available in the 3 most popular spigot sizes;
100, 125 and 150mm.
• Low loss foil backdraft damper and “operating”
light included.
• Front grille can be easily removed for cleaning.
• Internal thermal motor cut out protection.
• 230-240V, single-phase, 50Hz supply.
• Certificate of Approval number: ESO130139/00.
All dimensions in mm
MODEL NO. M3/HR† L/SEC† FAN SPEED
RPM
AVG. dB(A) @ 3M
WATTS VOLTS
DOM-100C 95 26 2500 34 13 230
DOM-125C 185 51 2500 39 20 230
DOM-150C 250 78 2200 41 25 230
WALL MOUNTED FAN
B D
E
CøA
B DF
G
AHø
Cø
Air Flow
Air Flow
DOM-125C
DOM-100C
DOM-150C
† Air flow without duct and fittings
WALL MOUNTED FANS
See page 109 for performance curves.
19© FANTECH TRADE 2018
//
RE
SID
EN
TIA
L R
AN
GE
DOM FAN KITS
All dimensions in mm
DWK SERIES
• Exhaust to outside of building.
• In-built backdraft damper and “operating” light.
• BCA compliant for ventilation & energy efficiency.
• Internal thermal motor cut out protection.
• 220-240V, single-phase, 50Hz.
• Includes quality PFL grille with fly wire mesh.
MODEL NO. L/SEC*AVG. dB(A)
@ 3MAIR FLOW
(M3/H)†WATTS
DWK100 26/21 34 95 13
DWK125 51/42 30 185 28
DWK150 78/65 41 280 25
* Maximum air flow: fan only / fan with duct and fittings as supplied † Air flow without duct and fittings
MODEL NO. A B C D E F G H I J K
DWK100 158 168 20 62 99 109 109 99 28 15 155
DWK125 180 190 26 76 118 128 130 120 25 12 160
DWK150 200 200 25 104 148 158 160 150 34 15 175
KØH
JI
ØF
cuto
ut
ØG
cuto
ut
Exhaust Fan Wall Tube External Grille
230(trim to required length)
DWK100Includes DOM-100C (100mm exhaust fan)
DWK125Includes DOM-125C (125mm exhaust fan)
DWK150Includes DOM-150C (150mm exhaust fan)
All fan kits come with wall tube and external grille.
External GrilleDOM Exhaust Fan Wall Tube
FLY WIRE
INCLUDED
WALL MOUNTED FANS
20 © FANTECH TRADE 2018
RE
SID
EN
TIA
L R
AN
GE
//
EDM
MODEL NO.M3/HR†
L/SEC†
FAN SPEED RPM
AVG. dB(A) @ 3M
WATTS VOLTSIP
RATING
EDM-300C 280 78 2200 41 35 240 IPX4
† Air flow without duct and fittings
WALL MOUNTED FAN
Whether wall or ceiling mounted, the EDM exhausts stale
and moist air from homes and commercial buildings.
The robust mechanically driven backdraft shutter
prevents dust from infiltrating it even when switched
off, making it perfect for homes and on-site offices in
harsh conditions.
• Made from tough injection moulded plastic.
• Internal thermal motor cut out protection.
• 220-240V, single-phase, 50Hz.
• Certificate of Approval number: ESV140558.
BULK OPTION • Available in plain carton only.
• Minimum order quantity of 10
• Product code: EDM-300C-BULK.
ACCESSORIES • External Grilles.
• Flexible Duct - Fire Rated AS/NZS 4254.
• Wall Tubes.
WALL MOUNTED FANS
MODEL NO. DUCT SIZE A B C D
EDM-300C 150 200 129 148 104
Air Flow
Includes a high quality mechanical backdraft
shutter that prevents outside air coming into
building when fan is switched off.
The EDM’s electric shutters operate using wax motor
technology. The wax pot is a paraffin-filled cylinder
designed to open and close the shutter with a smooth and
gentle stroke. This reduces noise and ensures faultless
operation every time.See page 109 for performance curves.
21© FANTECH TRADE 2018
//
RE
SID
EN
TIA
L R
AN
GE
SLIMFIT
The Slimfit Grille and Spacer Plate have been specifically
designed to fit directly onto the spigot of an EDM-300C fan.
• Spacer Plate can be mounted on exterior or
interior wall.
• Made from UV-stabilised ABS Plastic.
• Comes with flywire mesh sheet to eliminate entry
of insects.
• Can also be used in thicker walls or ducted
applications using wall tube or flex duct.
• Available with 150mm spigot only.
INSTALLATION DATA
Can be installed into narrow panel wall applications from
45 to 130mm thick such as mining accommodation huts,
portable homes and site offices.
All dimensions in mm
EXTERNAL GRILLE
99 to130mm
EDM-300CDPL150Louvre
Wall
DPL150 Louvre
81 to98mm
1 x DPS150 Spacer Plate
EDM-300C
1 x DPS150Spacer Plate
DPL150Louvre
63 to80mm
1 x DPS150 Spacer Plate
EDM-300C
45 to62mm
2 x DPS150Spacer Plates
1 x DPS150Spacer Plate
DPL150Louvre
EDM-300C
Designed to fit directly
onto the EDM-300C wall
mounted fan for narrow
panel wall applications.
FLY WIRE
INCLUDED
Fan and grille combination designed
to be installed into narrow panel wall
applications from 45 to 130mm wide.
MADEMADE
WALL MOUNTED FANS
22 © FANTECH TRADE 2018
RE
SID
EN
TIA
L R
AN
GE
//
HCM Gravity operated louvre
shutter prevents the
ingress of dust and rain.
The HCM wall/window mounted fan is suitable for
domestic kitchens and bathrooms. It features powerful air
flow performance and quiet operation.
• Compact low profile design.
• Quiet operation.
• Can also be skylight mounted (see below).
• Powerful air flow performance.
• Rated “Continuous Run”.
• Wall rods, tubes and plates for wall mounting available in
the accessories section.
• 220-240V, single-phase, 50Hz.
• Certificate of Approval number:
HCM150-N - ESV170211,
HCM180-N - SAA-162771-EA,
HCM225-N - SAA-162771-EA.
Note: Must not be mounted directly above heat sources such as an oven.
MODEL NO. AØ B C DØ
HCM-150N 214 63 35 183-188
HCM-180N 255 100 35 220-225
HCM-225N 298 90 35 262-267
The Weather Cap has been designed for
skylight installation. It provides added
protection against both wind and
rain when the fan is mounted in
demanding areas such as high-rise
housing, seaside and exposed
positions. Another key feature is
that it comes with bird wire mesh
and is colour matched to the fan.
Model No: HCM-150CAP and HCM-180CAP.
MODEL NO.M3/HR
L/SEC
FAN SPEED RPM
AVG. dB(A) @ 3M
WATTS VOLTSIP
RATING
HCM-150N 210 58 1900 41 25 240 IPX4
HCM-180N 380 105 2000 42 28 240 IPX4
HCM-225N 630 175 1700 49 40 240 IPX4
WALL / WINDOW MOUNTED FANS
F
All dimensions in mm
OPTIONAL WEATHER CAP
i
WALL/WINDOW MOUNTED FANS
See page 109 for performance curves.
23© FANTECH TRADE 2018
//
RE
SID
EN
TIA
L R
AN
GE
STYLVENT Automatic, soft acting
motorised shutters
prevent wind sheer and
fan failure.
The Weather Cap provides
added protection against both
wind and rain when the fan
is mounted in demanding
areas such as high-rise
housing, seaside and
exposed positions. Another
key feature is that it comes with bird wire mesh
and is colour matched to the fan.
Model No’s: HV-150CAP, HV-230CAP, HV-300CAP.
WALL / WINDOW MOUNTED FANS
The Stylvent Series can be wall or window mounted making
them well suited for a wide range of general residential and
commercial exhaust or supply ventilation applications.
• Weather and impact resistant housing.
• Rated “Continuous Run”.
• Exhaust mode as standard .
• Can be direct wired in supply air mode
or dual mode with reversing switch.
(HV-230AE & HV-300AE only).
• Easy to clean removable cover.
• Wall rods and wall tubes for wall mounting available
in the accessories section.
• 220-240V, single-phase, 50Hz.
Certificate of Approval number: ESV150134.
22
Optional weather cap
3 - 25*
CE
xter
nalf
ace
Internalface
A
B
E
F
DØHole cutout
diameter
All dimensions in mm
MODEL NO. A B CDØ MIN
DØ MAX
E F
HV-150AE 230 251 110 185 190 130 306
HV-230AE 300 325 142 259 262 182 440
HV-300AE 368 403 150 327 330 215 570
* For walls 25mm to 300mm thick use wall rods
† Air flow in exhaust mode
OPTIONAL WEATHER CAP
i
MODEL NO.M3/HR†
L/SEC†
FAN SPEED RPM
AVG. dB(A) @ 3M
WATTS VOLTSIP
RATING
HV-150AE 225 63 1800 39 32 240 IPX4
HV-230AE 600 167 1250 43 34 240 IPX4
HV-300AE 1100 306 1150 46 68 240 IPX4
ACCESSORIES • Reversing switch
• Weather cap (see below)
WALL/WINDOW MOUNTED FANS
See page 109 for performance curves.
24 © FANTECH TRADE 2018
RE
SID
EN
TIA
L R
AN
GE
//
CEILING MOUNTED FANS
Optimised ImpellerSpecially designed forward curved centrifugal impeller with an optimised variable radius inlet path. Blades are positioned at specific angles and intervals to achieve maximum air flow and efficiency, resulting in more power and less noise.
Aerodynamic DesignAll parts of the fan have been aerodynamically engineered to allow air to flow through the fan with the least possible resistance, resulting in powerful performance matched with smooth and quiet operation. The inlet has been shaped to provide the smoothest entry for air and the expansion chamber is situated in the optimum position to guide air flow out of the fan.
Engineered GrilleThe matching grilles have been aerodynamically engineered to allow air to flow into the fan with minimal possible resistance, resulting in smooth efficient air flow and low noise levels.
Quiet Backdraft ShutterOur engineering team have developed an ultra quiet backdraft shutter. It produces minimal air flow resistance and requires no power to operate.
Powerful MotorDynamically balanced motor with hardened steel shaft and sealed for life silicone ball bearings guarantee an extra long life span matched with high speed operation and performance.
Built To LastWe know this fan has been built correctly with only quality components. This means we can offer a groundbreaking 5 year warranty.
A I R S C I E N C E
25© FANTECH TRADE 2018
//
RE
SID
EN
TIA
L R
AN
GE
MODEL NO. DESCRIPTIONCUT
OUT AØB C* D**
RESPF8 Fan body250 195 105/170 94/120
RESPF8-T Fan body with run-on timer
RESPF150 Fan body290 197 170 120
RESPF150T Fan body with run-on timer
The Response header box exhaust fan is the quietest and
most powerful in its class. It includes features such as a
unique swing clip and removable spigot that makes it very
easy to install. There are two sizes available; an 8 inch
model and a 10 inch model. Both are available with a
run-on timer.
• The ultra quiet 8” model is ideal for odour and dampness
removal from toilets, ensuites and cupboards.
• 10” model provides stronger air flow performance
to ensure steam is cleared from rooms such as
bathrooms and ensuites.
• Advanced impeller and housing design provides powerful
air flow and minimises noise.
• Can be retrofitted into an existing standard 8” and 10”
round fan cut out.
• Low resistance non-return backdraft damper
maximises air flow performance.
• Matching grilles are easy to remove, which makes cleaning easy.
• Includes sealed for life ball bearings.
• High strength swing clips make installation easy.
• Available with a modern square or round grille (See page
26). Square grille can be easily rotated to align with walls.
• Both models available with 3-15 minute adjustable run-on
timer (RESPF150T and RESPF8-T).
DUCTED CEILING FAN
RAPID RESPONSE
† Air flow without duct and fittings
All dimensions in mm
IPX4
MODEL NO.AIR
FLOW M3/HR†
AIR FLOWL/SEC†
FAN SPEED RPM
AVG. dB(A) @ 3M
WATTS VOLTS
RESPF8 216 60 950 29 30 230-240
RESPF150RESPF150T
349 97 950 37 60 230-240
SPECIAL NOTE
Timer model RESPF150T and RESPF8-T includes a plug and lead to suit HPM 33, or Clipsal 413/4P bases (with 4 pin sockets).
CEILING MOUNTED FANS
See page 110 for performance curves.
Long clip-in spigot makes installation & duct connection easier.
Rotate swing clips to hold fan body in place.
Tighten screws so clips clamp onto ceiling board.
* RESPF8 comes with spigot to suit both 100mm and 150mm duct.RESPF150 comes with spigot to suit 150mm duct only.
BD**C*
Cut Out A
RE
SID
EN
TIA
L R
AN
GE
//
MODEL NO. GRILLELUMENS
(LM)
INPUT POWER
(W)
COLOUR TEMP (K)
BEAM ANGLE (°C)
RESPG8-SQWH-LED
Square 1000 12 4200 180
RESPG8-RNWH-LED
Round 800 9 4200 180
RESPG150SQWH-LED
Square 1000 12 4200 180
RESPG150RNWH-LED
Round 800 9 4200 180
RAPID RESPONSEGRILLES WITH LED
The Rapid Response Grille with LED light will brighten up
any bathroom, ensuite or toilet. The LED light is positioned
in the centre of the grille and can be controlled separately
to the fan itself. It maintains a stylish, modern design to suit
any setting.
• LED light feature.
• Available in Round and Square.
• Available in 2 sizes to suit 8” and 10” Rapid Response
header box fan models.
• Stylish, contemporary design.
• LED light & Rapid Response Fan can be
controlled separately.
• Quick & easy to install.
• Can be retrofitted to a previously installed
Rapid Response Fan.
• Complies to: AS/NZS 60598.2.2:2001 and
AS/NZS 60598.1:2013 Certificate No.: SAA152082
26 © FANTECH TRADE 2018
Scan the code or take a
look on our website to
watch the fan in action
MODEL NO. GRILLE A B C D
RESPG8-SQWH -LED
8” Square Grille White Finish with LED
300 28 - -
RESPG8-RNWH -LED
8” Round Grille White Finish with LED
- - 294 19
RESPG150SQWH -LED
10” Square Grille White Finish with LED
353 30 - -
RESPG150RNWH -LED
10” Round Grille White Finish with LED
- - 332 24
All dimensions in mm
B D
CA
CEILING MOUNTED FANS
IPX4
//
RE
SID
EN
TIA
L R
AN
GE
RAPID RESPONSEGRILLES
The stylish Rapid Response Grille has a contemporary
design and is available in a white or black finish.
• Available in Round and Square.
• Available in 2 sizes to suit 8” and 10” Rapid Response
header box fan models.
• Stylish, contemporary design.
• Quick & easy to install.
• Can be retrofitted to a previously installed
Rapid Response Fan.
*Body of the Fan sold seperatelyDimensions in mm
Round Grille Installation
Pinch the ends of the metal spring
clips together.
Feed the clips through the small
slots on either side of the fan body.
Square Grille Installation
Push the grille onto the base of the
fan until the clips click into place.
Rotate the grille to the
desired position.
150Ø*
290ØCut Out
52
14030
353
Spigot can be mounted
horizontally or vertically.
* Oval spigot designed to fit
150mm duct.
RAPID RESPONSE CEILING GRILLE WITH CLIP-IN SPIGOTThe modern looking Response Ceiling Grille has been designed for ducted systems using an in-line fan and external grille. It features a clip-in spigot that can be positioned for horizontal or vertical duct connection.
• Can be retrofitted into a standard
10” round fan cut out.
• Unique ‘push-out’ ceiling clamps
make installation easy.
• Clip-in spigot makes installation and
duct connection easier.
• Grille can be easily rotated to align with
the walls and removed for cleaning.
Model No. RCG150SQWH27© FANTECH TRADE 2018
RESPG8-RNWHRESPG150RNWH
RESPG150RNBK
RESPG8-SQWHRESPG150SQWH
RESPG150SQBK
*
B D
CA
MODEL NO. GRILLE A B C D
RESPG8-SQWH8” Square Grille
White Finish300 28 - -
RESPG8-RNWH8” Round Grille
White Finish- - 294 19
RESPG150SQWH10” Square Grille
White Finish353 30 - -
RESPG150RNWH10” Round Grille
White Finish- - 332 24
RESPG150SQBK10” Square Grille
Black Finish353 30 - -
RESPG150RNBK10” Round Grille
Black Finish- - 332 24
All dimensions in mm
All dimensions in mm
28 © FANTECH TRADE 2018
RE
SID
EN
TIA
L R
AN
GE
//
Fresh air is drawn in from under the door cavity and stale air exhausted from the
powder room.
Fantech Trade Rapid Response is designed for long duct runs.
EFFECTIVE VENTILATION FOR INTERNAL POWDER ROOMS
Internal powder rooms can be difficult to ventilate properly due to the long
duct runs associated with the installation. The Fantech Trade Rapid Response
is the most powerful ducted ceiling mounted exhaust fan on the market.
CEILING MOUNTED FANS
29© FANTECH TRADE 2018
//
RE
SID
EN
TIA
L R
AN
GE
Sub-floor space
A rigid duct ‘Flat Pack’system has smooth inner surfaces to minimise pressure loss, while its “easy-to-fit” components make it easy to install.
Cathedral ceiling
Header box extraction fans such as the Rapid Response have been designed to fit into low ceiling heights. Ideal for clearing bathrooms of steam or toilets of odours.
HOME WITH CATHEDRAL CEILING
APARTMENT WITH LIMITED CEILING SPACE
Don’t trap your fan between tight ceiling spaces. Low profile fans and rigid
flat duct are ideal for cathedral ceilings or between sub-floors in multi-story
apartments or houses.
VENTILATION SYSTEMS FOR CATHEDRAL CEILING AND SUB-FLOOR INSTALLATIONS
CEILING MOUNTED FANS
30 © FANTECH TRADE 2018
RE
SID
EN
TIA
L R
AN
GE
//
MINITUBE
MODEL NO.AIR FLOW
M3/HR†L/
SEC†POWER SUPPLY
INPUT POWER
AVG. dB(A) @ 3M
DUCT SIZE
MTP132 361 100 50-60Hz 28W 45 150
† Air flow without duct and fittings
The Minitube Series of duct mounted axial fans is suitable
for exhausting or supplying air in domestic and commercial
applications such as bathrooms, toilets, ensuites and
apartments.
• Includes robust mounting feet.
• Light-weight but robust aluminium fan housing
with plastic spigots.
• Axial impellers made from plastic.
• Matches 150mm standard duct size.
• Can be speed controlled.
• Can be mounted in any position.
• Comes with plug and lead.
ACCESSORIES • VA2.0 Speed Controller.
• Flexible Duct - Fire Rated AS/NZS 4254.
• Backdraft Dampers.
• Internal and external grilles.
IN-LINE DUCT MOUNTED FAN
IP44
Ø145 186
83.5
20057
4 X Ø4.5
172146.5
Front
Side
Angle
Top
All dimensions in mm
IN-LINE DUCT MOUNTED FANS
See page 110 for performance curves.
31© FANTECH TRADE 2018
//
RE
SID
EN
TIA
L R
AN
GE
IN-LINE DUCT MOUNTED FAN
PROVENT
IP44
IN-LINE DUCT MOUNTED FANS
Dimensions in mm
The high performance ProVent fans feature a compact
design that makes them suitable for applications where
space is limited. Their mixed-flow impeller provides
powerful air flow making them suitable for homes,
apartments and commercial buildings.
• High performance mixed-flow Impeller.
• Models 150SW and 200SW include an
external mounted 2-speed switch.
• Models 150TSW and 200TSW include a
1-30 minute adjustable run-on timer and
external mounted 2-speed switch.
• Fan body can be removed for maintenance or
repair without disturbing the duct system via
specially designed support brackets.
• Integrated mounting foot makes installation easier.
• All models include plug and lead for easy
plug-in installation.
• Suitable for both supply and exhaust
air applications.
MODEL NO. A B C D E FØ GØ H J
RIL-100 100 60 115 80 303 97 176 190 220
RIL-125 100 60 115 80 258 123 176 190 210
RIL-150SW 112 60 127 80 295 147 200 225 236
RIL-200SW 124 94 141 100 302 198 217 235 265
RIL-150TSW 112 60 127 80 295 147 200 225 236
RIL-200TSW 124 94 141 100 302 198 217 235 265
FØ
E
D
GØ
A
H
B
C
J
* Includes a 1-30 minute adjustable run-on timer.
MODEL NO. SPEEDM3/HR†
L/SEC†
FAN SPEED RPM
DB(A) @ 3M
WATTS VOLTS
RIL-100High 245 68 2220 36 24 240
Low 202 56 1860 32 18 240
RIL-125High 360 100 2280 37 30 240
Low 270 75 1920 39 22 240
RIL-150SWHigh 576 160 2520 45 50 240
Low 443 123 1980 38 44 240
RIL-150TSW*
High 576 160 2520 45 50 240
Low 443 123 1980 38 44 240
RIL-200SWHigh 1008 280 2520 51 120 240
Low 792 220 1980 44 100 240
RIL-200TSW*
High 1008 280 2520 51 120 240
Low 792 220 1980 44 100 240
SPECIAL NOTES
Timer models RIL-150TSW and RIL-200TSW include a plug and lead to suit HPM 33 or Clipsal 413/4P bases (with 4 pin socket).RIL-150TSW and RIL-200TSW cannot be speed controlled.
ACCESSORIES
• Run-on Timers & Speed Controllers.
• Flexible Duct - Fire Rated AS/NZS 4254.
• Backdraft Dampers.
• Internal and external grilles.
See page 110 for performance curves.
32 © FANTECH TRADE 2018
RE
SID
EN
TIA
L R
AN
GE
//
The Silent Series of in-line mixed-flow fans incorporates a
number of new technologies that make them the quietest
fan in its class. This high performance fan is ideal for noise
sensitive areas such as apartments, hotels and offices
where rooms are often close together.
• High performance mixed-flow impeller.
• Low noise operation.
• Vibration absorbing elements are integrated into the
advanced body design.
• 360° rotating junction box makes connection of power
cable easier (applicable for 100, 125, 150 and
200mm sizes only).
• Integral mounting foot makes installation simple.
• 1 to 30 minute run-on timer available on 100 to
200mm models.
• Includes plug and lead for easy installation.
• Convenient 2-speed motor, factory set to high speed
(single speed on models with run-on timer).
• Fan body can be easily removed without disturbing
connected ductwork
TD SILENT
IP44
ACCESSORIES
• Run-on Timers & Speed Controllers. • Flexible Duct - Fire Rated AS/NZS 4254. • Backdraft Dampers. • Internal and external grilles.
IN-LINE DUCT MOUNTED FAN
IN-LINE DUCT MOUNTED FANS
† Air flow without duct and fittings * Includes a 1-30 minute adjustable run-on timer Performance data and curves shown are for high speed.
MODEL NO.M3/HR†
L/SEC†
FAN SPEED RPM
dB(A) @ 3M
WATTS VOLTS
TD-250/100SIL 240 66 2200 36 24 240
TD-250/100SILT-4PL* 240 66 2200 36 24 240
TD-350/125SIL 360 100 2250 33 30 240
TD-350/125SILT-4PL* 360 100 2250 33 30 240
TD-500/150SIL 570 158 2500 40 50 240
TD-500/150SILT-4PL* 570 158 2500 40 50 240
TD-800/200SIL 900 249 2780 42 95 240
TD-800/200SILT-4PL* 900 249 2780 42 95 240
TD-1300/250SIL 1270 352 2570 47 197 240
TD-2000/315SIL 1760 488 2680 50 297 240
360° rotating junction box.
Rubber gaskets on spigots help to reduce air leakage and absorb vibration. Easy to release clamps.
See page 110 for performance curves.
33© FANTECH TRADE 2018
//
RE
SID
EN
TIA
L R
AN
GE
MODEL NO. A B C D E F G HØ
TD-250/100SIL 100 83 223 233 250 121 575 97
TD-350/125SIL 100 83 223 233 250 121 462 123
TD-500/150SIL 116 96 245 251 250 134 484 147
TD-800/200SIL 145 129 296 296 340 164 568 198
MODEL NO. A B C D E F G HØ I
TD-1300/250SIL 300 280 331 387 200 171 680 248 140
TD-2000/315SIL 370 335 373 432 260 192 825 312 152
F
EI E I
B
C
G
DA 8.5
H
Dimensions in mm
Dimensions in mm
• Aerodynamic inlet improves air flow.
• Made from durable sheet steel.
COMPACT UNITS
HIGH COMPACT UNITS
100MM, 125MM, 150MM & 200MM
250MM & 315MM
IN-LINE DUCT MOUNTED FANS
34 © FANTECH TRADE 2018HEAT TRANSFER KITS
Heat Transfer Kits are designed to draw warm air from a
room with a heat source such as a fireplace or potbelly
stove, and deliver this warm air to other areas of the house.
They are easy to install and economical to run.
• High air velocity into rooms ensures warm air reaches
the occupants.
• Kits include all necessary components.
• High quality in-line fan includes plug
and lead.
• Easy to install and economical to run.
ACCESSORIES
• TFC6 Fan Control Thermostat.
• VA2.0 Speed Controller/Switch.
HEAT TRANSFER
• Kits designed for average room sizes of
4m x 4m x 2.5m high, or room volume 40m³.
• Air flow per outlet approx. 50L/sec.
• Minimum velocity at grille outlet is 3.0 to 4.0 m/sec.
• Larger rooms may require more than one outlet.
Outlet velocity3.0 to 4.0m/sec
Minimum air velocity approx. 1m/sec
1.5m
MODEL NO. FTPHTK1-1 FTPHTK1-2 FTPHTK1-3
AIR FLOW* (L/sec)
86 (62) 160 (107) 280 (183)
SOUND LEVEL (AVG. dB(A)@3m) 45 45 51
POWER (W) 28 50 120
INSULATED DUCT LENGTH (M) 9 12 15
MAXIMUM DUCT RUN† (M) 9 9 12
ADJUSTABLE GRILLES 2 3 4
DUCT TAPE ✓ ✓ ✓
BRANCH TAKE OFF x Double Triple
* Figure in brackets is as installed† Inlet to Outlet
IN-LINE DUCT MOUNTED FAN KIT
IP44One to One
Room(FTPHTK1-1)
One to Two Room
(FTPHTK1-2)
One to Three Room
(FTPHTK1-3)
(FTPHTK1-2)
35© FANTECH TRADE 2018
//
RE
SID
EN
TIA
L R
AN
GE
FIREPLACE
IN-LINE FAN
INSULATED DUCT
IN-LINE FAN
BRANCH TAKE OFF
INSULATED DUCT
FIREPLACE
FIREPLACE
IN-LINE FAN
INSULATED DUCT
BRANCH TAKE OFF
ONE TO TWO ROOM KIT INCLUDES1 X in-line mixed-flow fan with Ø150mm spigot
12 metre of insulated flexible duct
3 X Ø150mm ceiling mounted adjustable grille
1 X Ø150mm branch take off
1 X roll of duct tape
ONE TO THREE ROOM KIT INCLUDES1 X in-line mixed-flow fan with Ø200mm spigot
15 metre of insulated flexible duct
3 X Ø150mm ceiling mounted adjustable grille
1 X Ø200mm ceiling mounted adjustable grille
1 X Ø200mm branch take off
1 X roll of duct tape
ONE TO ONE ROOM KIT INCLUDES1 X in-line axial fan with Ø150mm spigot
9 metre of insulated flexible duct
2 X Ø150mm ceiling mounted adjustable grille
1 X roll of duct tape(FTPHTK1-2)
HEAT TRANSFER KITS
36 © FANTECH TRADE 2018
RE
SID
EN
TIA
L R
AN
GE
//
TOILET VENTILATION
The OdourVac Toilet Ventilation System solves the problem
of toilet odour in a quiet, unobtrusive manner. Odours are
drawn from the toilet bowl through the cistern’s overflow
pipe and exhausted by the ducted ventilation system to
outside the home. The fan is supplied with a 3-pin plug and
lead and is easily activated by using either a light switch,
a separate switch or a movement sensor (switches and
sensor purchased separately).
• Creates an odourless toilet by removing odours
directly from the toilet bowl.
• Adjustable air flow ensures odours are removed
without draft.
• The system complies with AS1668.2-2002 and
BCA 2010.
• Compatible with most toilet suites.
ODOURVAC
MODEL NO. DESCRIPTION
OVK1 OdourVac System
TEF100 Fan only (without spigots)
MODEL NO. VOLTAGE FREQUENCY INPUT POWER
TEF100 230-240V 50Hz 16W
MODEL NO. A B C DØ E F
TEF100 132 90 113 89 110 67
BALANCING VALVE
The system features a balancing valve that is fitted within
the toilet cistern. It adjusts the air flow to maintain a fresh
odour free environment while minimising drafts and noise.
KIT INCLUDESEuropean made in-line fan with spigots
Balancing valve
2 x 50mm diameter X 90° PVC elbow
50mm external wall grille
50mm diameter PVC socket
50mm diameter to 40mm diameter PVC reducer
250mm length of 40mm diameter PVC pipe
2 x 100mm length of 40mm diameter PVC pipe
200mm length of 40mm diameter flexible pipe
40mm diameter, 90 ° PVC elbow
2 x Circular cover plate
Items highlighted in pink are included.
Balancing valve
Fan (TEF100)
50mm external wall grille
FAN SPECIFICATIONS
Dimensions in mm
ODOURVAC TOILET VENTILATION KIT
37© FANTECH TRADE 2018
//
RE
SID
EN
TIA
L R
AN
GE
Air speed is extremely low
across the larger surface area of the pan,
speeding up as it moves
up to the over flow pipe.
Odours are extracted from
the cistern
Cistern’s over flow pipe is used as a
pathway from the pan to above
water level.
WANT AN ODOURLESS LOO?
The OdourVac System draws low volumes
of air into the pan during use preventing any
odour from escaping into the room. This
creates an odour free room at all times.
ODOURVAC TOILET VENTILATION KIT
38 © FANTECH TRADE 2018
RE
SID
EN
TIA
L R
AN
GE
//
Dimensions in mm
Exterior surface mounted fan that is very powerful and
easy to install. Ideal for downstairs toilets, laundries and
kitchens, or retrofitting an existing in-line fan system.
• Easy to install on exterior wall.
• Compact design for installation in tight spaces.
• Lightweight, durable construction.
• Powerful air extraction from one or more grilles.
• Insect proof cover.
• Easy access for cleaning.
• Can be used with variable speed controller.
• “Continuous rated” motor fitted with thermal protection.
• Grey colourbond finish can be painted to match
wall colour.
• 220-240V, single-phase, 50Hz.
ACCESSORIES • Run-on Timers and Speed Controllers.
• Flexible Duct.
• Internal Grilles.
• Backdraft Damper.
EZIFIT THRU WALL
160-190
100 310
Wall
Ø150 flexibleor rigid duct
(not included)
Foam SealingTape behind(included)
355
Outlet deflector
Air Flow
MODEL NO. M3/HR† L/SEC† FAN SPEED RPM
AVG.dB(A) @ 3M
WATTS VOLTS
EWE152 443 123 2500 46 70 240
EWE154 245 68 1440 35 30 240
† Air flow without duct and fittings
EXTERNAL WALL MOUNTED FAN
BUSHFIRE CODE COMPLIANT MODEL• Developed and tested for ducted
applications in bushfire prone regions.
• High quality bronze mesh provides ember protection.
• Compliant to AS3959:2009 up to and including BAL-40.
IP44
EXTERNAL WALL MOUNTED FANS
MODEL NO. TYPE
EWE152 Standard
EWE154 Standard
EWE152-BFC Bush fire compliant
EWE154-BFC Bush fire compliant
See page 110 for performance curves.
39© FANTECH TRADE 2018
//
RE
SID
EN
TIA
L R
AN
GE
EXTERNAL WALL MOUNTED FAN
Exterior flush mounted fan that is barely visible, very
powerful and easily accessible. The most effective way to
exhaust from downstairs laundries, kitchens and powder
rooms in a two storey home.
• Easy to install on exterior wall.
• Flush-mounted design provides an
unobtrusive appearance.
• Powerful air extraction from one or more grilles.
• Can be wired in High, Medium (standard) or Low speed.
• 3-Speed Switch available for speed control.
• 5-Star compliant when used with backdraft damper.
• “Continuous rated” motor fitted with thermal-protection.
• Supplied with flywire as standard.
• 220-240V, single-phase, 50Hz.
EZIFIT IN-WALL
MODEL NO. SPEEDM3/HR†
L/SEC†
FAN SPEED RPM
AVG. dB(A) @ 3M
WATTS VOLTS
EIE150
Low 295 82 1273 31 50 240
Medium* 425 118 1939 44 60 240
High 558 155 2418 49 75 240
† Air flow without duct and fittings * Fan supplied pre-wired in medium speed
IP44
FLY WIRE
INCLUDED
Neutral colour grille to
complement most brick
colours; can be easily
painted if required.
EXTERNAL WALL MOUNTED FANS
See page 111 for performance curves.
Dimensions in mm
110
75
External Wall
Fan
320
300
CutoutSize:265
Cutout Size:240
Air Flow
150ØDuct
ACCESSORIES
• Run-on Timers.
• 3-Speed Switch.
• Flexible Duct - Fire Rated AS/NZS 4254.
• Internal Grille.
• Backdraft Damper.
40 © FANTECH TRADE 2018
RE
SID
EN
TIA
L R
AN
GE
//
Available in metal/deck and tile roof versions, the Ezifit Thru Roof exhaust and supply air fans are easy to install and provide powerful air flow with low noise output. A relief vent version (ie. without the fan) is also available.
• Easy to install design.
• Suits all types of tile or metal roof profiles.
• Roof flashing included (excludes bush fire code
compliance models).
• Comes with convenient 3-pin plug and lead.
• Suitable for connection to long duct runs.
• Good installation will provide quiet operation.
• “Continuous rated” motor with safety
thermal protection.
• Galvanised metal finish - easy to paint.
• Custom colour available as an optional extra.
• 220-240V, Single-phase, 50Hz.
• Ezifit Relief Vent ideal for 150mm and 200mm duct
mounted fan systems.
ACCESSORIES
• Run-on Timers and Speed Controllers.
• Flexible Duct - Fire Rated AS/NZS 4254.
• Internal Grilles.
• Backdraft Damper.
EZIFIT THRU ROOFMODEL NO. TYPE AØ B C DØ EØ
ECE152* Exhaust Fan 140 100 700 285 150
ECE154* Exhaust Fan 140 100 700 285 150
ECE204* Exhaust Fan 200 153 750 445 200
ERV150* Relief Vent 140 100 608 285 150
ERV200* Relief Vent 200 153 750 445 200
* Nominate roof flashing type: M= Metal/Deck roof, T= Tile roof All dimensions in mm
Tile VersionMetal Roof Version
MODEL NO. M3/HR† L/SEC†
FAN SPEED RPM
AVG. dB(A) @ 3M
WATTS VOLTS
ECE152* 532 148 2500 44 70 240
ECE154* 277 77 1440 35 30 240
ECE204* 1280 356 1400 46 90 240
† Air flow without duct and fittings * Nominate roof flashing type: M = Metal/Deck roof, T= Tile roof; -BFC = Bushfire Code compliant
ROOF MOUNTED FAN
ROOF MOUNTED FANS
F
EZIFIT EXHAUST & RELIEF VENT
EZIFIT RELIEF VENT• Ideal for 150mm & 200mm duct mounted fan systems.
• For dimensions and product codes see above table.
See page 111 for performance curves.
41© FANTECH TRADE 2018
//
RE
SID
EN
TIA
L R
AN
GE
Dimensions in mm
EZIFIT WITH BUSHFIRE CODE COMPLIANCE
EØ
B (max)
A
CD
• Developed and tested for ducted
applications in bushfire prone
regions.
• Robust, galvanised steel
construction.
• High quality bronze mesh provides
ember protection.
• Compliant to AS3959:2009 up to
and including BAL-40.
MODEL NO. AØ B C DØ EØ
ECE152-BFC 200 265 55 256 286
ECE154-BFC 200 265 55 256 286
ECE204-BFC 350 415 55 315 445
ROOF MOUNTED FANS
Dimensions in mm
EZIFIT SUPPLY AIR
F
• Provides filtered air to
internal spaces.
• Designed to provide powerful air
flow through 150mm duct
to one or more points.
• Suitable for connection to
long duct runs.
• Fitted with a G2 dust filter that
can be cleaned or replaced.
MODEL NO. M3/HR† L/SEC† FAN SPEED RPM
dB(A) @ 3M WATTS VOLTS
ECE152S* 461 128 2460 51 110 240
† Air flow without duct and fittings * Nominate roof flashing type: M = Metal/Deck roof, T= Tile roof
Model No. ECE152*S *Nominate roof flashing type: M= Metal/Deck roof, T= Tile roof
See page 111 for performance curves.
MODEL NO. FAN SPEED RPM AVG DB(A) @3MECE.. 1 PH. APPROX
WEIGHT KG
VOLTSWATTS AMPS
ECE152-BFC 2460 44 70 0.30 4 240
ECE154-BFC 1380 35 30 0.16 4 240
ECE204-BFC 1360 46 90 0.40 10.5 240
RE
SID
EN
TIA
L R
AN
GE
//
42 © FANTECH TRADE 2018
POWER SENSE SWITCH
RUN-ON TIMER DIRECT WIRED SUPPLY WITH PLUG-IN OUTLET. SINGLE SWITCH INPUT
RUN-ON TIMER4-PIN PLUG SUPPLY WITH PLUG-IN OUTLET
SPEED CONTROLLER3-PIN PLUG SUPPLY WITH PLUG-IN OUTLET
Provides automatic on/off control of a fan from an appliance when current is detected, ie: clothes dryer, range hood booster fan. LED lights indicate when load is activated. 220-240V, single phase, 50Hz.
PART NO. LOAD SENSE ON LOAD SENSE OFFMAX. FAN OUTPUT
ENCLOSURE SIZE (W X H X D) MM
VZ-ISNSE 2.0A to 15A 1.5A 5A 153 × 110 × 60
VZ-ISNSE-LC 0.5A to 2.0A 0.35A 5A 153 × 110 × 60
RUN-ON TIMER DIRECT WIRED
PART NO. RUN-ON TIME MAX. AMPS TO SUIT FAN SELECTED
VZ6-4PL 6 min 5.0Vogue/RingPlate, Ezifit Thru Wall, Ezifit Thru Roof, TD Silent,
Response, ProVent
220-240V, single-phase, 50Hz. Designed to permit the supply of electricity to motors so they can continue to operate for a predetermined time. Can be mounted within equipment or enclosure. Size: 32W x 13H x 17D
220-240V, single-phase, 50Hz. Fan with 3-pin plug and lead connects directly. Mains connection is wired directly into the terminals of the run-on timer; no need for 4-pin GPO.
220-240V, single-phase, 50Hz. Fan with 3-pin plug and lead connects directly. Fitted with 4-pin plug and 900mm lead for connection to 4-pin GPO. 6 minute fixed timer.
220-240V, single-phase, 50Hz. Fan with 3-pin plug and lead connects directly. Fitted with 3-pin plug and 900mm lead for connection to 3-pin GPO.
PART NO. MAX. AMPS TO SUIT FAN SELECTED
VA1.5-3PL 1.5 Vogue/RingPlate, Ezifit Thru Wall, Ezifit Thru Roof, TD Silent, Response, ProVent
PART NO. START DELAY RUN-ON TIMER AMPS TO SUIT FAN SELECTED
VZ24C Up to 150 secUp to 24min
(1.5 min increments)0.075-1.25
Domestique, Silent Design,Silent, HCM, Stylvent, ProVent, Response, Ezifit Thru Wall, Ezifit In-Wall, Ezifit
Thru Roof, Vogue/Ring PlateVZ6 50 sec 6 min Fixed
VZ12 50 sec 12 min Fixed
PART NO. RUN-ON TIME MAX. AMPS TO SUIT FAN SELECTED
VZ2-10TS 2-10 min 5.0Domestique, Silent Design, Silent, HCM, Stylvent, ProVent, Response,
Ezifit Thru Wall, Ezifit In-Wall, Ezifit Thru Roof, Vogue/Ring Plate
FAN CONTROLLERS
//
RE
SID
EN
TIA
L R
AN
GE
43© FANTECH TRADE 2018
VARIABLE SPEED CONTROLLER
FAN CONTROL THERMOSTAT
SPEED CONTROLLER/SWITCH
3-SPEED SWITCH
REVERSING SWITCH
A stepless speed controller for single phase AC external rotor motors. A potentiometer may be used in lieu of input signals to provide manual control when in 0-10V control. Rated at 240V, 3 Amp, suitable for 50/60 Hz 600VA up to 55°C.
220-240V, single-phase, 50/60 Hz. The Fan Control Thermostat has been developed to control the operation of a 240V fan, based on the setting made on the thermostat dial. It can be set to turn on a fan when the room temperature either goes higher or lower than the dial setting.
Wall mounted Fan Speed Controller with on/off switch. Provides infinite variation of fan speed from 100% down to approximately 30% of full speed. 240V, single phase, 50Hz.
240V, single-phase, 50Hz. Wall mounted 3-speed switch that has been specifically designed for the Ezifit In-Wall Exhaust Fan to change between high, medium and low speed. Has an IP30 enclosure rating. A recess depth of 25mm is required for mounting.
240V, single-phase, 50Hz. Wall-mounted Reversing Switch with an IP30 enclosure rating. A recess depth of 25mm is required for mounting. Enables the Stylvent fans to operate in both supply and exhaust modes.
PART NO. INPUT SIGNALDIMENSIONS
(W X H X D) MM AMPS TO SUIT FAN SELECTED
AVA3.00-10V or
2-20mA is selected via an internal jumper.
110 × 40 × 50
3.0
When used to control a number of identical fans the sum of the full load amps of all the
connected fans must not exceed 85% of the maximum rating of the controller. The fans
must be wired in parallel.AVA3.0-IP55 165 ×142 × 84
PART NO. MAX. AMPS LED POWER LIGHT TO SUIT FAN SELECTED
VA2.0 2.0 No
When used to control a number of identical fans the sum of the full load amps of all the connected fans must not exceed 85% of the maximum rating of the
controller. The fans must be wired in parallel.
VA2.8 2.8 Yes
VA5.0 5.0 No
VA8.0 8.0 Yes
VA2.0POT** 2.0 No
PART NO. TO SUIT FAN SELECTED
DSS1-16 Ezifit In-Wall models
PART NO. TO SUIT FAN SELECTED
SRS Stylvent. HV-230AE and HV300AE only
PART NO. TEMP. RANGE MAX. AMPS TO SUIT FAN SELECTED
TFC6 5˚ - 30˚C 6.0Ideal for Heat Transfer Fan Kits.
Suitable for most 240V fans.
** The VA2.0POT unit is designed to be mounted within equipment or enclosures.
FAN CONTROLLERS
RE
SID
EN
TIA
L R
AN
GE
//
44 © FANTECH TRADE 2018
• Temperature rating -70°C to +220°C.
• Complies with Australian/New Zealand Standards:
Fire and smoke control - AS/NZS 1668.1
4 zero fire rating - AS/NZS 1530.3
PART NO.DUCT
DIAMETER, MMDUCT LENGTH, M
BULK PACK CONTENTS
DUCT100-3MPK 100 3 -
DUCT125-3MPK 125 3 -
DUCT150-6MPK 150 6 -
DUCT200-6MPK 200 6 -
DUCT250-6MPK 250 6 -
DUCT300-6MPK 300 6 -
DUCT100-6M 100 6 20 lengths
DUCT125-6M 125 6 20 lengths
DUCT150-6M 150 6 20 lengths
DUCT200-6M 200 6 20 lengths
PART NO.DUCT
DIAMETER, MMDUCT LENGTH, M
DUCT150INS-6M 150 6
DUCT200INS-6M 200 6
DUCT250INS-6M 250 6
PART NO.DUCT
DIAMETER, MM DUCT LENGTH, M COMPRESSED, MM
DUCT125-3-SRIG 125 3 750
DUCT150-3-SRIG 150 3 750
DUCT200-3-SRIG 200 3 750
FLEXIBLE DUCT (NON-INSULATED)
FLEXIBLE DUCT (INSULATED)
SEMI-RIGID ALUMINIUM DUCTING
• Suitable for general exhaust and supply air applications such as bathrooms,
ensuites and toilets.
• Fibre woven metallic duct provides durability and tear resistance.
• High tensile wire sprung to retain duct shape and flexibility.
• Complies with Australian/New Zealand Standards: Construction contains
high grade flame retardant with a 3 zero fire rating - AS/NZS 4254.
• Thermally insulated outer sleeve to minimize heat gain or heat loss.
• Fibre woven metallic inner duct provides durability and tear resistance.
• High tensile wire sprung to retain duct shape and flexibility.
• Complies with Australian/New Zealand Standards: Construction contains
high grade flame retardant with a 3 zero fire rating - AS/NZS 4254.
• Well suited to clothes dryers, range hoods, bathrooms and other general ventilation applications as it holds its shape when formed around obstacles.
DUCT & DUCT FITTINGS
//
RE
SID
EN
TIA
L R
AN
GE
45© FANTECH TRADE 2018
Designed to divide air flow in ducted systems.
Made from injected-moulded ABS flame retardant material.
Branch Take Off (BTO)Y Piece (YP)
Designed to divide air flow in ducted systems. Made
from injected-moulded ABS flame retardant material.
PART NO.DUCT
DIAMETER, MM (FAN SIDE)
NO. OF DUCT BRANCHES
BRANCH DIAMETERS,
MM
YP-100-100-100* 100 2 100
YP-125-125-125* 125 2 125
YP-150-150-150 150 2 150
BTO-150-150-150 150 2 150
YP-200-150-150 200 2 150
BTO-200-200-150 200 2 200 & 150
YP-250-250-250 250 2 250
YP-250-200-200 250 2 200
YP-300-300-300 300 2 300
YP-300-200-200 300 2 200
PART NO.DUCT
DIAMETER, MM (FAN SIDE)
NO. OF DUCT BRANCHES
BRANCH DIAMETERS,
MM
DBTO-200-3X150 200 3 150
DBTO-250-3X200 250 3 200
DBTO-300-3X200 300 3 200
PART NO. SUIT DUCT DIAMETERS, MM
FR-2 100 to 400
Y-PIECES AND BRANCH TAKE OFFS
DOUBLE BRANCH TAKE OFFS
Ducting system with FlexRight Common installation (without FlexRight)
Efficient unrestricted
airflow
Heatingor cooling
device Kinked flexible duct restricting airflow
Heatingor cooling
device
FlexRight 90 Bend
Low LowHigh High
Medium Medium
Energy Used
Energy Used
FlexRight
Duct Elbow
FlexRight installation
in a duct system
* Made from metal
The FlexRight Duct Elbow is designed to improve the
efficiency of a heating and air conditioning system. It does
this by removing kinks in ductwork and creating a 90° bend
with a large and smoother radius which improves air flow.
• Helps minimise load on ducted heating & cooling units
• Suitable for both new and existing duct installations
• Reduces noise from your system
FLEXRIGHT DUCT ELBOW
DUCT & DUCT FITTINGS
RE
SID
EN
TIA
L R
AN
GE
//
46 © FANTECH TRADE 2018
LOW PROFILE DUCT SYSTEM
Supaflo Flatpack duct is a low profile alternative to round
PVC pipe commonly used in ventilation systems. It has a
compact design that makes it ideal for applications where
space is limited. It also features a smooth inner surface
which minimises pressure loss and therefore improves air
flow. The modular, slide-together design of the system
makes it simple to install into most applications. There are
two sizes of Supaflo ducting available, the 125 series and
the 165 series.
• Designed for exhaust and supply air ventilation systems.
• Duct can be cut down to size to fit into virtually any space.
• Large range of fittings ensures duct can be installed into
most applications.
• Specially designed flat channel clip makes mounting
duct easy.
• Components are easy to join, light weight, corrosion
resistant and hygienic.
TESTING
UL181.11-2013, AS1530.3-1999
Fantech Trade Supaflo Flatpack ducting has been shown to
comply with BCA2016 as an alternative solution. For further
information please contact your local sales office for the
latest copy of the Perform BC Fire Engineering Assessment
“Fantech Flatpack Duct System”.
SUPAFLO
SUPAFLO LOW PROFILE DUCT SYSTEM
//
RE
SID
EN
TIA
L R
AN
GE
47© FANTECH TRADE 2018
LOW PROFILE DUCT DESCRIPTION 125 SERIES - CODE 165 SERIES - CODE
Flat rigid duct 2 metre long
FPD125-DUCT-2M FPD165-DUCT-2M
Duct connector FPD125-CONDD FPD165-CONDD
Self seal connector duct to duct FPD125-CONSSDD -
Self seal connector duct to fitting FPD125-CONSSDF FPD165-CONSSDF
90° Horizontal bend FPD125-HBEND-90 FPD165-HBEND-90
45° Horizontal bend FPD125-HBEND-45 FPD165-HBEND-45
90° Vertical bend FPD125-VBEND-90 FPD165-VBEND-90
45° Vertical bend FPD125-VBEND-45 FPD165-VBEND-45
Equal T piece FPD125-TPIECE FPD165-TPIECE
Flexible bend FPD125-FLEXBEND FPD165-FLEXBEND
Round / rectangular rotating
transition 90° bend - Ø150mmFPD125-TR150-90 -
Round / rectangular transition
90° bend - Ø150mm- FPD165-TR150-90
Round / rectangular transition
90° bend - Ø125mm- FPD165-TR125-90
Round / rectangular transition - Ø125mm
FPD125-TR125 -
Round / rectangular transition - Ø150mm
- FPD165-TR150
Wall plate FPD125-WPR -
Duct clip - plastic FPD125-CLIP -
Duct clip - metal FPD125-CLIPMETAL FPD165-CLIPMETAL
125-100
150-100
150-125
200--150
125-100
150-100
150-125
200--150
125-100
150-100
150-125
200--150
125-100
150-100
150-125
200--150
CIRCULAR REDUCER / EXPANDERS DESCRIPTION CODE
Circular reducer / expander Ø125mm to Ø100mm
FPD-RED125/100
Circular reducer / expander Ø150mm to Ø100mm
FPD-RED150/100
Circular reducer / expander Ø150mm to Ø125mm
FPD-RED150/125
Circular reducer / expander Ø200mm to Ø150mm
FPD-RED200/150
204mm 220mm
60mm 90mm
SUPAFLO LOW PROFILE DUCT SYSTEM
48 © FANTECH TRADE 2018
RE
SID
EN
TIA
L R
AN
GE
//
MODEL NO. (SINGLE UNIT ONLY)
MODEL NO. (FOR BULK
PACK)
NO. OF GRILLES IN BULK PACK
DUCT DIAMETER
AØB C D
PGL100PK PGL100 20 100 140 15 34
PGL125PK PGL125 10 125 160 12 24
PGL150PK PGL150 10 150 175 15 34
Dimensions in mm
Dimensions in mm
Dimensions in mm
PGL EXTERNAL GRAVITY LOUVRE GRILLE
• Designed to withstand harsh outdoor conditions,
made with impact & UV resistant PVC.
• Includes flywire mesh sheet to eliminate entry of insects.
• Available in 100mm, 125mm, 150mm & 200mm.
• Designed to withstand harsh outdoor conditions, made with impact & UV
resistant PVC.
• Includes shutters that open when the fan is running and close when it is off.
• Available in 100mm, 125mm & 150mm.
MODEL NO.(SINGLE UNIT ONLY)
MODEL NO. (FOR BULK
PACK)
NO. OF GRILLES IN BULK PACK
DUCT DIAMETER
AØB C D
EPFL100PK EPFL100 20 100 155 16 29
EPFL125PK EPFL125 10 125 155 16 29
EPFL150PK EPFL150 10 150 186 17 37
PFL200PK PFL200 15 200 285 25 50
FLY WIRE
INCLUDED Includes flywire mesh sheet toeliminate entry of insects.
ALUMINIUM EXTERNAL FIXED LOUVRE GRILLE
• Comes with a galvanised steel spigot that fits inside the wall cavity, leaving
the front face to finish flush to the wall.
• Its rigidly-fixed horizontal blades are designed to reduce the possibility of
rainwater entry.
• Vermin proof mesh is fitted to minimise the entry of debris.
MODEL NO.DUCT
DIAMETER AØ
B C D E F
ELDA200 200 297 60 95 20 250
ELDA250 250 345 60 95 25 300
Grille Duct Spigot
E
E
F
MADEMADE
EPFL/PFL EXTERNAL FIXED LOUVRE GRILLE
EXTERNAL GRILLES
//
RE
SID
EN
TIA
L R
AN
GE
49© FANTECH TRADE 2018
Dimensions in mm Dimensions in mm
MODEL NO.DUCT
DIAMETER AØB C D
EDVSS100 100 130 147 50
EDVSS125 125 165 187 50
EDVSS150 150 189 210 60
MODEL NO.DUCT
DIAMETER AØB C D E
EHVSS100 100 156 50 58 156
EHVSS125 125 180 50 66 184
EHVSS150 150 181 60 78 184
A
B
C
D
A D
E
B
C
MADEMADE MADEMADE
The Dome Vent EDVSS is designed for external wall
mounting and can be installed within minutes. The
stainless steel dome protects against harsh elements and
the mesh screen prevents pests from entering. Perfect for
extreme weather conditions. The valve body is equipped
with a mounting gasket that forms an air tight seal.
• Ideal for extreme weather conditions.
• High quality 304 stainless steel.
• Includes mounting gasket.
• Cinder mesh with a 2mm aperture to comply with
bushfire attack code BAL-40.
The Hood Vent EHVSS is installed within minutes. Its gravity
backdraft shutter prevents cold air flowing back into the
room and insects from entering. Made from high quality
stainless steel to minimise the risk of rust. It is perfect for
regions with extreme weather conditions. The valve body is
equipped with a mounting gasket that forms an air tight seal.
• Ideal for extreme weather conditions.
• Includes gravity backdraft shutter.
• High quality 304 stainless steel.
• Includes mounting gasket.
• Cinder mesh with a 2mm aperture to comply with
bushfire attack code BAL-40.
FOR EXTERNAL MOUNTING FOR EXTERNAL MOUNTING
DOME VENT HOOD VENT
EXTERNAL GRILLES
RE
SID
EN
TIA
L R
AN
GE
//
MODEL NO. AØ DUCT DIAMETER BØ C
IDVSS100 140 100 58
IDVSS125 172 125 58
IDVSS150 217 150 70
MODEL NO. AØ DUCT DIAMETER BØ C D
IDV100 140 100 74 39
IDV150 201 150 120 51
50 © FANTECH TRADE 2018
Dimensions in mm
Dimensions in mm
MADEMADE MADEMADE
The IDV is constructed from high quality steel with a white
finish. The valve body is equipped with a mounting ring
for ease of installation. Air flow can be easily adjusted by
rotating the control disc.
• Manufactured from high quality steel with a white finish.
• Stylish design.
• Adjustable air flow.
• Quick & easy installation.
• Includes mounting ring.
The IDVSS is constructed with high quality 304 stainless
steel to minimise the risk of rust. The valve body is
equipped with a mounting ring for ease of installation.
It can be used for both return and supply air with air flow
easily adjusted by rotating the control disc.
• Constructed with 304 quality stainless steel.
• Stylish design.
• For both return & supply air.
• Quick & easy installation.
• Includes mounting ring.
INTERNAL DUCT VALVE INTERNAL DUCT VALVE
IDV IDVSS
A
B
C
FRONT FACE FRONT FACE
BACK BACK
INTERNAL GRILLES
//
RE
SID
EN
TIA
L R
AN
GE
51© FANTECH TRADE 2018
MODEL NO.NO.
OF SLOTSCOLOUR A† B C D E F† G H
LSD125-600A 1 Anodised Silver
172 550 553 100 80 105 200 55
LSD125-600W 1 White
LSD225-600A 2 Anodised Silver
172 550 553 139 126 105 200 98
LSD225-600W 2 White
The sleek looking Linear Slot internal exhaust grilles have
been designed to suite the modern and contemporary
bathroom, ensuite or toilet. They come with a 150mm duct
connection and are available in single and dual slot. Comes
in white and silver finishes as standard.
• Discretely blends into the latest architecturally designed
bathroom or ensuite.
• Works in conjunction with a duct mounted, roof mounted
or external wall mounted fan.
• High quality galvanised steel cushion head box.
• Oval spigot allows 150mm duct connection.
• Available with single slot, or dual slot for additional air flow.
LINEAR SLOT
† Oval shaped duct spigot suits 150mm flexible duct. All dimensions mm
INTERNAL GRILLE
G
A FED H
BC
A
B
D
C
F
G
E
H
SINGLE SLOT
DOUBLE SLOT
INTERNAL GRILLES
RE
SID
EN
TIA
L R
AN
GE
//
52 © FANTECH TRADE 2018INTERNAL GRILLES
PART NO.DUCT
DIAMETER AØ
BØ C DHOLE
CUTOUT Ø
ILG125PK 125 170 26 60 130
ILG INTERNAL CEILING GRILLECeiling mounted inlet/outlet clip-in grille.
ECG INTERNAL CEILING GRILLE Ceiling mounted inlet grille.
PART NO.DUCT
DIAMETER AØ
B C DHOLE
CUTOUT Ø
ECG100PK 100 140 10 35 100
ECG125PK 125 160 13 25 125
ECG150PK 150 175 12 35 150
Dimensions in mm
Dimensions in mm
Dimensions in mm
MADEMADE
MADEMADE
INTERNAL CEILING GRILLE
INTERNAL CEILING GRILLE
IDJG
IALG/ALG
• Air flow can be easily adjusted
by rotating the control disk.
• Sleek, stylish design with a
non-reflective white surface.
• High quality ABS plastic,
scratch & chip resistant.
• Air flow can be easily adjusted by
rotating central button.
• High quality ABS plastic, scratch &
chip resistant.
• Non-reflective white surface.
PART NO.(SINGLE UNIT ONLY)
PART NO. (FOR BULK
PACK)
NO. OF GRILLES
IN BULK PACK
DUCT DIAMETER
AØBØ C D
HOLE CUTOUT
Ø
IALG150PK IALG150 10 150 260 16 90 232
IALG200PK - 200 315 16 95 282
ALG250PK - 250 390 16 100 355
ALG300PK - 300 440 16 100 405
PART NO.(SINGLE UNIT ONLY)
PART NO. (FOR BULK
PACK)
NO. OF GRILLES
IN BULK PACK
DUCT DIAMETER
AØ BØ C D
HOLE CUTOUT
Ø
IDJG150PK IDJG150 10 150 240 5 95 206
IDJG200PK - 200 290 5 115 256
Dimensions in mm
//
RE
SID
EN
TIA
L R
AN
GE
53© FANTECH TRADE 2018 ACCESSORIES
B50
Air Flow
AØ
Dimensions in mm
Dimensions in mm
WALL PLATES
WALL TUBES
WALL RODS
PART NO.
DIMENSIONS TO SUIT FAN SELECTED
AØ B ProVent TD Silent Ezifit In-Wall Ezifit Thru
WallEzifit Thru
Roof
SJK150 150 161 RIL-150.. TD-500.. EIE150EWE152 EWE154
ECE152 ECE154
SJK200 200 211 RIL-200.. TD-800.. ECE204
PART NO.
DIMENSIONS TO SUIT FAN SELECTED
AØ B ProVent TD Silent Ezifit In-WallEzifit Thru
WallEzifit Thru
Roof
RSK100 100 88 RIL-100 TD-250.. - - -
RSK125 125 88 RIL-125 TD-350.. - - -
RSK150 150 88 RIL-150.. TD-500.. EIE150EWE152 EWE154
ECE152 ECE154
RSK200 200 88 RIL-200.. TD-800.. - - ECE204
RSK250 250 128 TD-1300.. - - -
RSK315 315 128 TD-2000.. - - -
PART NO.HOLE
DIAMETERWIDTH HEIGHT
TO SUIT FAN SELECTED
STYLVENT HCM
WP130PK 185 300 320 HV-150AE HCM-150N
WP180PK 219 300 320 HCM-180N
WP225PK 259 425 425 HV-230AE HCM-225N
PART NO.SPIGOT
DIAMETER RANGE
LENGTH
TO SUIT FAN SELECTED
DOMESTIQUE SILENT EDMSILENT DESIGN
RING PLATE
VOGUE STYLVENT HCM
WT130PPK 100 - 130 280DOM-100.. DOM-125..
SILENT-100.. SILENT-125..
SILDES100.. SILDES200..
- - - -
WT230PPK 150 - 230 280 DOM-150.. SILENT-150..EDM-300C
SILDES300.. RP20.. VCW20.. HV-150AEHCM-150NM HCM-180NM
WT370PPK 250 - 370 280 - - - -RP25.. RP30.. RP35..
VCW25.. VCW30..
HV-230AE HV-300AE
HCM-225NM
SJK BACKDRAFT DAMPER (GRAVITY)
RSK BACKDRAFT DAMPER (SPRING LOADED)
Compared to conventional spring loaded backdraft dampers, the SJK has superior performance characteristics due to its unique design that provides minimal resistance to air flow. The flap closes when the fan is off.
The tube is constructed from galvanised steel and the flaps from aluminium. Flaps are spring-loaded and when the fan is switched off they close providing a seal.
Wall Rods are specifically designed for the Stylvent and HCM fans. They are required if the fan is to be installed in walls 25mm - 300mm thick. Comes in packs of 4 wall rods
PART NO.TO SUIT FAN SELECTED
STYLVENT HCM
WALLRODSPK All Models All models
SJK150
B
AØ
RSK150
See page 111 for performance curves.
Dimensions in mm
Dimensions in mm
See page 111 for performance curves.
top related