r-2000ib operator manual [b-82234en 07]
Post on 08-Nov-2015
6.721 Views
Preview:
DESCRIPTION
TRANSCRIPT
-
< > R-2000*B
OPERATORS MANUAL
B-82234EN/07
MECHANICAL UNIT
-
Before using the Robot, be sure to read the "FANUC Robot Safety Manual (B-80687EN)" and understand the content. This manual can be used with controllers labeled R-30iA or R-J3iC. If you have a controller labeled R-J3iC, you should read R-30iA as R-J3iC throughout this manual. No part of this manual may be reproduced in any form. All specifications and designs are subject to change without notice. The products in this manual are controlled based on Japans Foreign Exchange and Foreign Trade Law. The export from Japan may be subject to an export license by the government of Japan. Further, re-export to another country may be subject to the license of the government of the country from where the product is re-exported. Furthermore, the product may also be controlled by re-export regulations of the United States government. Should you wish to export or re-export these products, please contact FANUC for advice. In this manual we have tried as much as possible to describe all the various matters. However, we cannot describe all the matters which must not be done, or which cannot be done, because there are so many possibilities. Therefore, matters which are not especially described as possible in this manual should be regarded as impossible.
-
B-82234EN/07 SAFETY PRECAUTIONS
s-1
1 SAFETY PRECAUTIONS For the safety of the operator and the system, follow all safety precautions when operating a robot and its peripheral devices installed in a work cell.
1.1 OPERATOR SAFETY Operator safety must be given the highest priority in robot system operation. It is very dangerous to enter the robot work area while the system is operating. Be sure to review your safeguards before starting robot system operation. The following lists the general safety precautions. Careful consideration must be made to ensure operator safety. (1) Have the robot system operators attend the training courses held
by FANUC.
FANUC provides various training courses. Contact our sales office for details.
(2) Even when the robot is stationary during operation, it may be ready to operate while, for example, waiting for a start signal. In this condition, the robot is still regarded as in motion. To ensure operator safety, make sure that an operator can be aware of the robot in motion by a warning light or some other visual indication, or an audible alert.
(3) Be sure to install a safety fence with a safety gate around the system so that no operator can enter the inside of the fence without opening the gate. The safety gate must be equipped with an interlock switch, a safety plug, and the like so that the robot stops if the safety gate is opened.
The controller is designed such that signals from the interlock switch and the like can be connected. The signals set the robot to the emergency stop state if the safety gate is opened. See Fig. 1.1 for connection.
(4) Provide the peripheral devices with appropriate grounding (Class
A, Class B, Class C, or Class D). (5) Try to install the peripheral devices outside the work area. (6) Draw an outline on the floor, clearly indicating the range of the
robot motion, including the tools such as a hand. (7) Install a mat switch or photoelectric switch on the floor with an
interlock to a visual or aural alarm that stops the robot when an operator enters the work area.
-
SAFETY PRECAUTIONS B-82234EN/07
s-2
(8) If necessary, install a safety lock so that no one except the operator in charge can turn on the power of the robot.
The circuit breaker installed in the controller is designed to disable anyone from turning it on when it is locked with a padlock.
(9) When adjusting each peripheral device independently, be sure to
turn off the power of the robot.
Interlock switch and safety plug that are activated if the gate is opened
RM1 Motor power/brake
RP1Pulsecoder RI/RO,XHBK,XROT
Fig.1.1 Safety Fence and Safety Gate
Note) Terminals EAS1, EAS11, EAS2, and EAS21 are provided on the
terminal block of the printed circuit board that is placed in the operators box or on the operators panel.
-
B-82234EN/07 SAFETY PRECAUTIONS
s-3
1.1.1 Operator Safety An operator refers to a person who turns on and off the power to the robot system and starts a robot program from, for example, the operators panel during daily operation. Operators cannot work in the inside of the safety fence. (1) Operate the robot system from outside the safety fence. (2) If it is not necessary for the robot to operate, turn off the power of
the robot controller or press the EMERGENCY STOP button, and then proceed with necessary work
(3) Install an EMERGENCY STOP button within the operator's reach.
The robot controller is designed to be connected to an external EMERGENCY STOP button. With this connection, the controller stops the robot operation when the external EMERGENCY STOP button is pressed. See the diagram below for connection.
(Note) Connect EES1 and EES11.
Connect EES2 and EES21.
Fig.1.1.1 Connection Diagram for External Emergency Stop Switch
-
SAFETY PRECAUTIONS B-82234EN/07
s-4
1.1.2 Safety of the Programmer While teaching the robot, it is necessary for the operator to enter the work area of the robot. It is particularly necessary to ensure the safety of the programmer. (1) Unless it is specifically necessary to enter the robot work area,
carry out all tasks outside the area. (2) Before teaching the robot, check that the robot and its peripheral
devices are all in the normal operating condition. (3) If it is inevitable to enter the robot work area to teach the robot,
check the locations, settings, and other conditions of the safety devices (such as the EMERGENCY STOP button, the DEADMAN switch on the teach pendant) before entering the area.
(4) The programmer must be extremely careful not to let anyone else enter the robot work area.
The operators panel from FANUC is provided with an EMERGENCY STOP button and a key switch (mode switch) for selecting an automatic operation mode (AUTO) or teach mode (T1 or T2). Before opening the safety gate to enter the inside of the safety fence for teaching purposes, set the switch to a teach mode, and then remove the key from the mode switch to prevent anyone else from changing the operation mode carelessly. While still in the automatic operation mode, the robot enters the emergency stop state if the safety gate is opened. Once the switch has been set to a teach mode, the safety gate is disabled. When conducting work, the programmer should be responsible for keeping other people from entering the inside of the safety fence while being aware of that the safety gate is disabled.
The teach pendant from FANUC is provided with a DEADMAN switch as well as an EMERGENCY STOP button. The button and switch function as follows: (1) EMERGENCY STOP button: Causes an emergency stop when pressed. (2) DEADMAN switch: Functions differently depending on the mode switch setting.
(a) Automatic operation mode: The DEADMAN switch is disabled. (b) Teach mode: Causes an emergency stop when released or strongly pressed. Note) The DEADMAN switch is provided to set the robot to the emergency stop state when the operator releases or strongly presses the teach pendant in case of emergency. The R-30iA adopts a 3-position DEADMAN switch. The operator can enable the robot to operate by pressing the DEADMAN switch to its intermediate point. When the operator releases or strongly presses the DEADMAN switch, the robot enters the emergency stop state.
The controller determines that the operator intends to start teaching when the operator has preformed two successive actions: setting the teach pendant enable switch to ON, and then pressing the DEADMAN switch. When conducting work, the operator should be responsible for assuring safety while being aware of that the robot is ready to operate in this condition.
-
B-82234EN/07 SAFETY PRECAUTIONS
s-5
The teach pendant, operators panel, and peripheral device interface each have a single signal for starting robot operation. Whether these signals are valid depends on the settings of the mode switch and DEADMAN switch on the operators panel, the teach pendant enable switch, and the remote switch on the software, as shown below.
Mode Teach pendant
enable switch Remote switch
Teach pendant
Operators panel
Peripheral devices
Local Not allowed Not allowed Not allowed ON Remote Not allowed Not allowed Not allowed Local Not allowed Allowed to start Not allowed
AUTO Mode
OFF Remote Not allowed Not allowed Allowed to startLocal Allowed to start Not allowed Not allowed ON
Remote Allowed to start Not allowed Not allowed Local Not allowed Not allowed Not allowed
T1,T2 mode
OFF Remote Not allowed Not allowed Not allowed
(5) Before starting the robot from the operators box or operators
panel, make sure that nobody is in the robot work area and that the robot is normal.
(6) When a program is completed, be sure to carry out a test run according to the procedure below. (a) Run the program for at least one operation cycle in the single
step mode at low speed. (b) Run the program for at least one operation cycle in the
continuous operation mode at low speed. (c) Run the program for one operation cycle in the continuous
operation mode at the intermediate speed and check that no abnormalities occur due to a delay in timing.
(d) Run the program for one operation cycle in the continuous operation mode at the normal operating speed and check that the system operates automatically without trouble.
(e) After checking the completeness of the program through the test run above, execute it in the automatic operation mode.
(7) During automatic operation, the programmer must be outside the safety fence.
-
SAFETY PRECAUTIONS B-82234EN/07
s-6
1.1.3 Safety of the Maintenance Technician For the safety of maintenance technicians, the following should be carefully noted. (1) Never enter the robot work area during operation. (2) During maintenance work, the power to the controller should be
off where possible. Lock the main breaker with the key or the like, if necessary, to prevent anyone else from turning on the power.
(3) If it is inevitable to enter the robot work area while the power is on, press the EMERGENCY STOP button on the operators box, operators panel, or teach pendant, and then enter the area. The worker must indicate that the maintenance work is in progress, and must also be careful not to let anyone else operate the robot carelessly.
(4) When disconnecting the pneumatic system, be sure to reduce the supply pressure.
(5) Before starting maintenance work, check the robot and peripheral devices for dangerous or abnormal conditions.
(6) Never perform automatic operation if anybody is in the robot work area.
(7) When it is necessary to maintain the robot alongside a wall or instrument, or when multiple workers are working nearby, make certain that their escape path is not obstructed.
(8) When a tool is mounted on the robot, or when any moving device other than the robot is installed, such as belt conveyor, pay careful attention to its motion.
(9) When doing work, have a person stand beside the operators box or operators panel to press the EMERGENCY STOP button at any time; the person should be familiar with the robot system and able to sense any danger.
(10) When replacing or reinstalling components, take care to prevent foreign matter from entering the system.
(11) Before touching units, printed circuit boards, and other parts for inspection of the inside of the controller, or for any other purposes, be sure to turn off the power with the controller main breaker to protect against electric shock.
(12) When replacing parts, be sure to use those specified by FANUC. In particular, never use fuses or other parts of non-specified ratings. They may cause a fire or result in damage to the components in the controller.
(13) Before restarting the robot system after completion of maintenance work, make sure that nobody is in the work area and the robot and peripheral devices are normal.
-
B-82234EN/07 SAFETY PRECAUTIONS
s-7
1.2 SAFETY OF THE TOOLS AND PERIPHERAL DEVICES
1.2.1 Precautions in Programming (1) Use a limit switch or other sensor to detect a dangerous condition
and, if necessary, design the program to stop the robot when the sensor signal is received.
(2) Design the program to stop the robot when an abnormal condition occurs in any other robots or peripheral devices, even though the robot itself is normal.
(3) For a system in which the robot and its peripheral devices are in synchronous motion, particular care must be taken in programming so that they do not interfere with each other.
(4) Provide a suitable interface between the robot and its peripheral devices so that the robot can detect the states of all devices in the system and can be stopped according to the states.
1.2.2 Precautions for Mechanism
(1) Keep the component cells of the robot system clean, and operate
the robot in an environment free of grease, water, and dust. (2) Use mechanical unit cable that have required user interface. Please
do not obstruct the movement of the mechanical unit cable when cables are added. ( Please never tie an external cable to the mechanical unit cable by using the nylon band etc. ) Moreover, please do not interfere with the mechanical unit cable when equipment is installed in the robot. If these precautions are not observed There is a possibility that the mechanical unit cable is disconnected and the trouble not anticipated occurs.
(3) Employ a limit switch or mechanical stopper to limit the robot motion so that the robot or cable does not strike against its peripheral devices or tools.
-
SAFETY PRECAUTIONS B-82234EN/07
s-8
1.3 SAFETY OF THE ROBOT MECHANISM
1.3.1 Precautions in Operation (1) When operating the robot in the jog mode, set it at an appropriate
speed so that the operator can manage the robot in any eventuality. (4) Before pressing the jog key, be sure you know in advance what
motion the robot will perform in the jog mode.
1.3.2 Precautions in Programming (1) When the work areas of robots overlap, make certain that the
motions of the robots do not interfere with each other. (2) Be sure to specify the predetermined work origin in a motion
program for the robot and program the motion so that it starts from the origin and terminates at the origin. Make it possible for the operator to easily distinguish at a glance that the robot motion has terminated.
1.3.3 Precautions for Mechanisms
(1) Keep the work area of the robot clean, and operate the robot in an
environment free of grease, water, and dust.
1.3.4 Procedure to move arm without drive power in emergency or abnormal situations
(1) For emergency or abnormal situations (e.g. persons trapped in or
by the robot), brake release unit can be used to move the robot axes without drive power.
Please order following unit and cable.
Name Specification
Brake release
unit
A05B-2450-J350
(Input Voltage AC100-115V single-phase)
A05B-2450-J351
(Input Voltage AC200-240V single-phase)
Robot connection
cable
A05B-2450-J360 (5m)
A05B-2450-J361 (10m)
Power cable
A05B-2525-J010 ( 5m) (AC100-150V type)
A05B-2525-J011 ( 10m) (AC100-150V type)
A05B-2450-J364 ( 5m) (AC200-200V type)
A05B-2450-J365 ( 10m) (AC200-200V type)
-
B-82234EN/07 SAFETY PRECAUTIONS
s-9
(2) Please make sure that adequate numbers of brake release units are available and readily accessible for robot system before installation.
(3) Regarding how to use brake release unit, please refer to Robot controller maintenance manual.
NOTE Robot systems installed without adequate number of
brake release units or similar means are not in compliance with EN ISO 10218-1 nor with the Machinery Directive and therefore cannot bear the CE marking.
CAUTION Robot arm would fall down by releasing its brake because of gravity. Especially because spring balancer is used for J2-axis, it is hard to predict J2-arm movement by the condition of Robot attitude and end effecter.Therefore it is strongly recommended to take adequate measures such as hanging Robot arm by a crane before releasing a brake.(There is no balancer for R-2000iB/170CF,150U,165CF)
Eyebolt(M10,M12)2 leverblocks
Eyebolt(M10) pcs slings
In case of releasing a motor brake
Unpredictable
?
?
Method of supporting Robot arm
Fig. 1.3.4(a) Releasing J2 motor brake and measures (R-2000iB/165F,210F,165R,200R,100P,125L,175L,100H)
-
SAFETY PRECAUTIONS B-82234EN/07
s-10
Eyebolt(M10) pcs slings
Fall down
In case of releasing a motor brake Method of supporting Robot arm
Fig. 1.3.4(b) Releasing J3 motor brake and measures
(R-2000iB/165F,210F,165R,200R,100P,125L,175L,100H)
Fall down
Fall down
Supporting method of arm forR-2000iB/165CFR-2000iB/170CF(floor mount)
Supporting method of arm forR-2000iB/150UR-2000iB/170CF(top mount)
Fig. 1.3.4(c) Releasing J2 and J3 motor brake and measures (R-2000iB/170CF,150U,165CF)
-
B-82234EN/07 SAFETY PRECAUTIONS
s-11
1.4 SAFETY OF THE END EFFECTOR
1.4.1 Precautions in Programming (1) To control the pneumatic, hydraulic and electric actuators,
carefully consider the necessary time delay after issuing each control command up to actual motion and ensure safe control.
(2) Provide the end effector with a limit switch, and control the robot system by monitoring the state of the end effector.
-
SAFETY PRECAUTIONS B-82234EN/07
s-12
1.5 WARNING LABEL (1) Greasing and degreasing label
Fig. 1.5 (a) Greasing and Degreasing Label
Description
When greasing and degreasing, observe the instructions indicated on this label. 1) When greasing, be sure to keep the grease outlet open. 2) Use a manual pump to grease. 3) Be sure to use a specified grease.
CAUTION See Section 7 CHECKS AND MAINTENANCE for
explanations about specified greases, the amount of grease to be supplied, and the locations of grease and degrease outlets for individual models.
-
B-82234EN/07 SAFETY PRECAUTIONS
s-13
(2) Disassembly prohibitive label
Fig. 1.5 (b) Disassembly Prohibitive Label
Description Do not disassemble the balancer unit because it contains a spring, which may cause serious danger (for the R-2000iB, a disassembly prohibitive label is affixed only to the balancer). (3) Step-on prohibitive label
Fig. 1.5 (c) Step-on Prohibitive Label
Description Do not step on or climb the robot or controller as it may adversely affect the robot or controller and you may get hurt if you lose your footing as well.
-
SAFETY PRECAUTIONS B-82234EN/07
s-14
(4) High-temperature warning label
Fig. 1.5 (d) High-temperature warning label
Description Be cautious about a section where this label is affixed, as the section generates heat. If you have to inevitably touch such a section when it is hot, use a protective provision such as heat-resistant gloves. (5) Transportation label
>2500kg
>2500kg
>630kg x4
-
B-82234EN/07 SAFETY PRECAUTIONS
s-15
Fig. 1.5 (f) Transportation label (R-2000iB/165R, 200R, 100P)
2500kg
>630kg X4
>1000kg X4
>2500kg
Fig. 1.5 (g) Transportation label (R-2000iB/165CF)
-
SAFETY PRECAUTIONS B-82234EN/07
s-16
Description When transporting the robot, observe the instructions indicated on this label. 1) Using a forklift Use a forklift having a load capacity of 2,500 kg or greater. Keep the total weight of the robot to be transported to within 2,200
kg, because the withstand load of the forklift bracket (option) is 5,390 N (550 kgf).
2) Using a crane Use a crane having a load capacity of 2,500 kg or greater. Use at least four slings each having a withstand load of 9,800 N
(1,000 kgf) or greater. Use at least four eyebolts each having a withstand load of 6,174 N
(630 kgf) or greater.
CAUTION Transportation labels are model-specific. Before
transporting the robot, see the transportation label affixed to the J2 base side.
See Sub-section 1.1 TRANSPORTATION for explanations about the posture a specific model should take when it is transported.
-
B-82234EN/07 SAFETY PRECAUTIONS
s-17
(6) Balancer replacement label
150kg J2=0
Fig.1.5 (h) Balancer replacement label (R-2000iB/165F,210F,125L,175L,100H)
300kg
J2=-90
Fig. 1.5 (i) Balancer replacement label (R-2000iB/165R,200R, 100P)
Description When replacing the balancer, observe the instructions indicated on this label. The above balancer replacement label indicates the following:
While replacing the balancer, keep the J2-axis at 0 for the R-2000iB/165F, 210F, 125L, 175L and 100H and keep the J2-axis at -90 for the R-2000iB/165R, 200R and 100P.
For the R-2000iB/165F, 210F, 125L, 175L and 100H the mass of the balancer is 150 kg.
For the R-2000iB/165R, 200R and 100P the mass of the balancer is 300 kg.
The R-2000iB/165CF has no balancer.
CAUTION For information about balancer replacement, contact
FANUC.
-
SAFETY PRECAUTIONS B-82234EN/07
s-18
(7) Motion range and load capacity label
In the case of CE specification, the following label is added:
0DEG-180DEG+180DEG
MAX. PAYLOAD : 165kg
Motion rangeof J5-axisrotation center
1919 2655
3045
370
J5-axis rotation center
Fig. 1.5 (j) Motion range label (example of R-2000iB/165F)
(8) Transportation prohibitive label (When transport equipment option is specified.)
Do not pull eyeboltsideways
Do not have impacton this part
Do not chain, pry,or strap on this part
Fig. 1.5 (k)Transportation prohibitive label
Description
Keep the following in mind when transporting the robot. 1) Do not pull eyebolts sideways 2) Prevent the forks of the forklift from having impact on a transport
equipment 3) Do not thread a chain or the like through a transport equipment.
-
B-82234EN/07 SAFETY PRECAUTIONS
s-19
(9) Transportation prohibitive label (When transportation equipment option A05B-1329-H075 is
specified.)
1) Remove the transport equipment after installing the robot
2) Remove all loads when transporting the robot. (Wrist and arm)
3) Always Place the robot in shipping position (refer to the manual) when transporting the robot Transport Equipment
Fig. 1.5(l) Transportation prohibitive label
Description
1) Remove the transport equipment after installing the robot. 2) Remove all loads when transporting the robot. (Wrist and arm) 3) Always place the robot in shipping position (refer to the manual)
when transporting the robot.
-
B-82234EN/07 PREFACE
p-1
PREFACE This manual explains the maintenance and connection procedures for the mechanical units of the following robots:
Model name Mechanical unit specification No. Maximum load
FANUC Robot R-2000iB/165F A05B-1329-B201 165kg FANUC Robot R-2000iB/210F A05B-1329-B205 210kg FANUC Robot R-2000iB/165R A05B-1329-B221 165kg FANUC Robot R-2000iB/200R A05B-1329-B225 200kg FANUC Robot R-2000iB/100P A05B-1329-B231 100kg FANUC Robot R-2000iB/170CF A05B-1329-B241 170kg FANUC Robot R-2000iB/125L A05B-1329-B261 125kg FANUC Robot R-2000iB/175L A05B-1329-B265 175kg FANUC Robot R-2000iB/100H A05B-1329-B271 100kg FANUC Robot R-2000iB/165CF A05B-1324-B541 165kg FANUC Robot R-2000iB/150U A05B-1329-B291 150kg
The label stating the mechanical unit specification number is affixed in the position shown below. Before reading this manual, determine the specification number of the mechanical unit.
FANUC LTD OSHINO-MURA.YAMANASHI PREF. JAPAN
TYPENO.DATE
WEIGHT kg
(1)
(2) (3) (4) (5)
-
PREFACE B-82234EN/07
p-2
TABLE 1 (1) (2) (3) (4) (5)
CONTENTS - TYPE No. DATE WEIGHT (Without controller)FANUC Robot R-2000iB/165F A05B-1329-B201 1170kg
FANUC Robot R-2000iB/210F A05B-1329-B205 1240kg
FANUC Robot R-2000iB-165R A05B-1329-B221 1480kg
FANUC Robot R-2000iB-200R A05B-1329-B225 1540kg
FANUC Robot R-2000iB/100P A05B-1329-B231 1560kg
FANUC Robot R-2000iB/170CF A05B-1329-B241 800kg
FANUC Robot R-2000iB/125L A05B-1329-B261 1190kg
FANUC Robot R-2000iB/175L A05B-1329-B265 1260kg
FANUC Robot R-2000iB/100H A05B-1329-B271 1150kg
FANUC Robot R-2000iB/150U A05B-1329-B291 1070kg
LETTERS
FUNUC Robot R-2000iB/165CF A05B-1324-B541
PRINT SERIAL NO.
PRINT PRODUCTION YEAR AND MONTH
1050kg
Position of label indicating mechanical unit specification number
-
B-82234EN/07 PREFACE
p-3
RELATED MANUALS
For the FANUC Robot series, the following manuals are available: Safety handbook B-80687EN All persons who use the FANUC Robot and system designer must read and understand thoroughly this handbook
Intended readers : All persons who use FANUC Robot, system designer Topics : Safety items for robot system design, operation, maintenance
R-30iA controller Operations manual SPOT TOOL+ B-82594EN-1 HANDLING TOOL B-82594EN-2 DISPENSE TOOL B-82594EN-4 Servo Gun Function B-82634EN
Intended readers : Operator, programmer, maintenance person, system designer Topics : Robot functions, operations, programming, setup, interfaces, alarms Use : Robot operation, teaching, system design
Maintenance manual B-82595EN B-82595EN-1 (For Europe) B-82595EN-2 (For RIA)
Intended readers : Maintenance person, system designer Topics : Installation, connection to the controller, maintenance Use : installation, start-up, connection, maintenance
-
B-82234EN/07 Table of Contents
c-1
TABLE OF CONTENTS
SAFETY PRECAUTIONS............................................................................s-1 PREFACE....................................................................................................p-1
1 TRANSPORTATION AND INSTALLATION ...........................................1 1.1 TRANSPORTATION...................................................................................... 2
1.1.1 Transportation with an End Effector Attached.......................................................24 1.2 INSTALLATION ........................................................................................... 26
1.2.1 Installation method .................................................................................................27 1.3 MAINTENANCE AREA................................................................................ 33 1.4 INSTALLATION SPECIFICATIONS ............................................................ 37
2 CONNECTION WITH THE CONTROLLER ..........................................38 2.1 CONNECTION WITH THE CONTROLLER................................................. 39
3 BASIC SPECIFICATIONS.....................................................................40 3.1 ROBOT CONFIGURATION......................................................................... 41 3.2 MECHANICAL UNIT OPERATION AREA AND
INTERFERENCE AREA .............................................................................. 50 3.3 ZERO POINT POSITION AND MOTION LIMIT........................................... 61 3.4 WRIST LOAD CONDITIONS....................................................................... 67 3.5 LOAD CONDITIONS ON J2-AXIS BASE AND J3-AXIS ARM..................... 90
4 MECHANICAL COUPLING TO THE ROBOT.......................................99 4.1 MECHANICAL COUPLING OF END EFFECTOR TO WRIST .................. 100 4.2 INSTALLING A FANUC/SPECIAL FLANGE ADAPTER
(R-2000iB/165F, 210F, 165R, 200R, 100P, 125L, 175L,100H)................................................................................................................... 110
4.3 EQUIPMENT MOUNTING FACE .............................................................. 111 4.4 LOAD SETTING ........................................................................................ 121 4.5 INERTIA LOAD SETTING ......................................................................... 123
5 PIPING AND WIRING TO THE END EFFECTOR...............................125 5.1 AIR SUPPLY (OPTION) ............................................................................ 126 5.2 AIR PIPING (OPTION) .............................................................................. 130 5.3 INTERFACE FOR OPTION CABLE (OPTION) ......................................... 132
-
Table of Contents B-82234EN/07
c-2
6 AXIS LIMITS SETUP...........................................................................152 6.1 SETTING MOTION LIMITATION BY SOFTWARE.................................... 153 6.2 HARD STOPPER AND LIMIT SWITCH SETTING .................................... 154 6.3 CHANGING THE MOTION RANGE BY THE LIMIT SWITCH
(OPTION) .................................................................................................. 167 6.4 ADJUSTING LIMIT SWITCH (OPTION) .................................................... 171
7 CHECKS AND MAINTENANCE .........................................................175 7.1 PERIODIC MAINTENANCE ...................................................................... 176
7.1.1 Daily checks .........................................................................................................176 7.1.2 3-month (960 hours) checks .................................................................................177 7.1.3 1.5-year (5,760 hours) checks ..............................................................................181 7.1.4 3-year (11,520 hours) checks ...............................................................................181 7.1.5 MAINTENANCE.................................................................................................181
7.2 Greasing the Balancer Shaft (1 year (3840 hours) Periodic Maintenance) ............................................................................................. 182 7.2.1 Replacing the Batteries1.5 Year checks .......................................................182 7.2.2 Replacing the Grease of the Drive Mechanism3 years (11,520 hours)
checks ...............................................................................................................183
7.2.3 Grease Replacement Procedure for the Wrist (R-2000iB/165F, 210F,
165R, 200R, 100P, 170CF,125L, 175L, 100H, 150U).........................................185 7.2.4 Grease Replacement Procedure for the Wrist (R-2000iB/165CF) .......................192
7.2.5 Procedure for Releasing Residual Pressure from the Grease Bath.......................193 7.2.6 Procedure for Releasing Residual Pressure from the Grease Bath ......................194
7.3 STORAGE ................................................................................................. 196
8 MASTERING .......................................................................................197 8.1 GENERAL ................................................................................................. 198 8.2 RESETTING ALARMS AND PREPARING FOR MASTERING
................................................................................................................... 200 8.3 ZERO POSITION MASTERING ................................................................ 201 8.4 QUICK MASTERING ................................................................................. 211
8.4.1 SINGLE AXIS MASTERING .............................................................................213 8.5 MASTERING DATA ENTRY...................................................................... 217
9 TROUBLESHOOTING ........................................................................219 9.1 OVERVIEW ............................................................................................... 220 9.2 FAILURES, CAUSES AND MEASURES................................................... 221
-
B-82234EN/07 Table of Contents
c-3
10 SEVERE DUST/LIQUID PROTECTION PACKAGE...........................228 10.1 SEVERE DUST/LIQUID PROTECTION PACKAGE (OPTION)
................................................................................................................... 228 10.2 SEVERE DUST/LIQUID PROTECTION CHARACTERISTICS ................. 229 10.3 CONFIGURATION OF THE SEVERE DUST/LIQUID
PROTECTION PACKAGE......................................................................... 230 10.4 NOTES ON SPECIFYING SEVERE DUST/LIQUID
PROTECTION PACKAGE......................................................................... 231
APPENDIX
A PERIODIC MAINTENANCE TABLE ...................................................235 B BOLT TIGHTENING TORQUE TABLE...............................................248
-
B-82234EN/07 1.TRANSPORTATION AND INSTALLATION
- 1 -
1 TRANSPORTATION AND INSTALLATION
-
1.TRANSPORTATION AND INSTALLATION B-82234EN/07
- 2 -
1.1 TRANSPORTATION The robot can be transported by a crane or a forklift. When transporing the robot, be sure to change the attitude of the robot to that shown below and lift by using the eyebolts and the transport equipment at their points.
CAUTION When hoisting or lowering the robot with a crane or
forklift, move it slowly with great care. When placing the robot on the floor, exercise care to prevent the installation surface of the robot from striking the floor strongly.
(1) Transportation using a crane (Fig. 1.1 (b) to (n))
Fasten the M20 eyebolts at the four points and lift the robot by the four slings. The robot is transported with the specific transport equipment attached for the R-2000iB/165R, 200R, 100P and 170CF. There are two kinds of transportation equipment about the type installed on the J1 base and the type installed on the J2 base.( There is no type installed on the J2 base in R-2000iB/170CF.)
NOTE When lifting the robot, notice so that the motor, connectors or cables of the robot are not damaged by slings.
(2) Transportation using a fork lift (Fig. 1.1 (o) to (z))
The robot is transported with the specific transport equipment attached. For the R-2000iB/165F, 210F, 165R, 200R, 100P, 125L, 175L and 100H, there are two types of transport equipment: one to be attached to the J1 base and the other to the J2 base. For the R-2000iB/170CF and 165CF,there is a type of transport equipment to be attached to the J1 base. Transport equipment are prepared as an option.
-
B-82234EN/07 1.TRANSPORTATION AND INSTALLATION
- 3 -
WARNING Please follow notes when it is necessary to transport robot with the base plate installed. The entire position of center of gravity is changed by
installing the tool and the base plate. Please note the balance enough. The tool swings by the vibration etc. when
transported, and there is a possibility that an excessive load acts on the robot. Secure the end effector firmly according to Subsection 1.1.1. When you lift robot with the base plate installed,
please lift up not the robot but the base plate. NOTE If the transport equipment of the J2 base type for
the R-2000iB/165R, 200R, and 100P is used with a crane or forklift to hoist or lower the robot in the state where the robot is tilted, all load may be imposed on the strut bar used to protect against falling, thus deforming the strut bar. When you operate a crane or fork lift ,please confirm whether the robot is the horizontal enough.
NOTE Loctite 262 (rust preventive) may be applied to the
mounting bolts used to secure the transport equipment of the J2 base type. When removing those mounting bolts, be careful not to damage the heads of the bolts.
WARNING Use the forklift pockets only to transport the robot
with a forklift. Do not use the forklift pockets for any other transportation method. Do not use the forklift pockets to secure the robot.
Before moving the robot by using forklift pockets, check and tighten any loose bolts on the forklift pockets.
-
1.TRANSPORTATION AND INSTALLATION B-82234EN/07
- 4 -
M20 tap through
To use eyebolt install to the out taps
M20 tap through
To use eyebolt install to the out taps
Fig. 1.1 (a) Position of the eyebolts and transportation equipment
-
B-82234EN/07 1.TRANSPORTATION AND INSTALLATION
- 5 -
1575
.5
317 305
NOTICE
See the list of specification for machine weight. Eyebolts complied with JISB 1168. Quantity Eyebolts 4 Sling 4
CraneCapacity min. 2.5 tonSlingCapacity min. 1.0 ton per 1
0or180
EYEBOLT(M20)Install to the out taps
Center ofgravity
476 348
477 348
1689.5
J2 AXISJ3 AXISJ4 AXISJ5 AXISJ6 AXIS
ROBOT POSTURE ON TRANSPORATION
J1 AXIS-60
0
0
0
0
Fig. 1.1 (b) Transportation using a crane (R-2000iB/165F)
-
1.TRANSPORTATION AND INSTALLATION B-82234EN/07
- 6 -
348477
1710.5
1575
.5
317 305
Center ofgravity
Eyebolts(M20)Install to the out taps.
CraneCapacity min. 2.5 tonSlingCapacity min. 1.0 ton per 1
NOTICE
See the list of specification for machine weight. Eyebolts complied with JISB 1168. Quantity Eyebolts 4 Sling 4
0or180
J2 AXISJ3 AXISJ4 AXISJ5 AXISJ6 AXIS
ROBOT POSTURE ON TRANSPORATION
J1 AXIS-60
0
0
0
0
Fig 1.1 (c) Transportation using a crane (R-2000iB/210F)
-
B-82234EN/07 1.TRANSPORTATION AND INSTALLATION
- 7 -
Eyebolts(M20)
1831
2012
Center ofgravity
Center ofgravity
1242
0J2 AXISJ3 AXISJ4 AXISJ5 AXISJ6 AXIS
J1 AXIS-12040 0 0 0
CraneCapacity min. 2.5 tonSlingCapacity min. 1.0 ton per 1
ROBOT POSTURE ON TRANSPORATION
NOTICE
See the list of specification for machine weight. Eyebolts complied with JISB 1168. Quantity Eyebolts 4 Sling 4
Transporteqpuipment (OPTION)
Fig 1.1 (d) Transportation using a crane (R-2000iB/165R J1 base type)
-
1.TRANSPORTATION AND INSTALLATION B-82234EN/07
- 8 -
Center ofgravity
Center ofgravity
Eyebolts(M20)
1831
2025
1242
0J2 AXISJ3 AXISJ4 AXISJ5 AXISJ6 AXIS
J1 AXIS-12040 0 0 0
CraneCapacity min. 2.5 tonSlingCapacity min. 1.0 ton per 1
ROBOT POSTURE ON TRANSPORATION
NOTICE
See the list of specification for machine weight. Eyebolts complied with JISB 1168. Quantity Eyebolts 4 Sling 4
Transportequipment (OPTION)
Fig 1.1 (e) Transportation using a crane (R-2000iB/200R J1 base type)
-
B-82234EN/07 1.TRANSPORTATION AND INSTALLATION
- 9 -
1828
2272
Center ofgravity
Center ofgravity
0J2 AXISJ3 AXISJ4 AXISJ5 AXISJ6 AXIS
J1 AXIS-12041 0 0 0
CraneCapacity min. 2.5 tonSlingCapacity min. 1.0 ton per 1
ROBOT POSTURE ON TRANSPORATION
NOTICE
See the list of specification for machine weight. Eyebolts complied with JISB 1168. Quantity Eyebolts 4 Sling 4
Transport equipment(OPTION)
Eyebolt (M20)
Fig 1.1 (f) Transportation using a crane (R-2000iB/100P J1 base type)
-
1.TRANSPORTATION AND INSTALLATION B-82234EN/07
- 10 -
CraneCapacity min 2.5 ton
SlingCapacity min 1.0 ton
NOTE See the list of specification for machine weight. Eyebolt complied with JISB 1168. Quantity Eyebolt 4 Sling 4
11501113
909
Center ofgravity
0or 180
J2 AXISJ3 AXISJ4 AXISJ5 AXIS
J1 AXIS
0
0
0
-55
ROBOT POSTURE ON TRANPORTATION
Eye bolt(M20)
Transportequipment
Fig 1.1 (g) Transportation using a crane (R-2000iB/170CF)
-
B-82234EN/07 1.TRANSPORTATION AND INSTALLATION
- 11 -
12072012
1831
Transportequipment(OPTION)
Center ofgravity
CraneCapacity : min. 2.5 min
SlingCapacity : min. 10 ton
ArbitraryJ2 AXISJ3 AXISJ4 AXISJ5 AXISJ6 AXIS
ROBOT POSTURE ONTRANSPORTATIONJ1 AXIS
-12040 0 0 0
NOTICE) See the list of specification for machine weight. Eyebolt complied with JISB 1168. Quantity eyebolt 4 sling 4
When you transport robot, please transport it absolutely by the posture for transporation.When you transport robot, remove all tools.Remove transport equipment absolutely after you set robot up.
Fig 1.1 (h) Transportation using a crane (R-2000iB/165R J2 base type)
-
1.TRANSPORTATION AND INSTALLATION B-82234EN/07
- 12 -
1207
1831
2025 Transportequipment(OPTION)
Center ofgravity
CraneCapacity : min. 2.5 ton
SlingCapacity : min. 1.0ton
ArbitraryJ2 AXISJ3 AXISJ4 AXISJ5 AXISJ6 AXIS
ROBOT POSTURE ONTRANSPORTATIONJ1 AXIS
-12040 0 0 0
NOTICE) See the list of specification for machine weight. Eyebolt complied with JISB 1168. Quantity eyebolt 4 sling 4
When you transport robot, please transport it absolutely by the posture for transporation.When you transport robot, remove all tools.Remove transport equipment absolutely after you set robot up.
Fig 1.1 (i) Transportation using a crane (R-2000iB/200R J2 base type)
-
B-82234EN/07 1.TRANSPORTATION AND INSTALLATION
- 13 -
CraneCapacity : min. 2.5 ton
SlingCapacity : min. 1.0ton
NOTICE) See the list of specification for machine weight. Eyebolt complied with JISB 1168. Quantity eyebolt 4 sling 4
When you transport robot, please transport it absolutely by the posture for transporation.When you transport robot, remove all tools.Remove transport equipment absolutely after you set robot up.
12072272
1825
ArbitraryJ2 AXISJ3 AXISJ4 AXISJ5 AXISJ6 AXIS
ROBOT POSTURE ONTRANSPORTATIONJ1 AXIS
-12041 0 0 0
Transportequipment(OPTION)
Center ofgravity
Fig 1.1 (j) Transportation using a crane (R-2000iB/100P J2 base type)
-
1.TRANSPORTATION AND INSTALLATION B-82234EN/07
- 14 -
Center ofgravity
Eyeblots(M20)Install to the out taps.
1575
.5
317 305348477
2044.5
0or180
J2 AXISJ3 AXISJ4 AXISJ5 AXISJ6 AXIS
J1 AXIS -60
0
0
0
0
NOTICE) See the list of specification for machine weight. Eyebolt complied with JISB 1168. Quantity eyebolt 4 sling 4
CraneCapacity : min. 2.5 ton
SlingCapacity : min. 1.0ton
ROBOT POSTURE ONTRANSPORTATION
Fig 1.1 (k) Transportation using a crane (R-2000iB/125L)
-
B-82234EN/07 1.TRANSPORTATION AND INSTALLATION
- 15 -
1910
1565
348477
Center ofgravity
317 305
CraneCapacity min. 2.5 tonSlingCapacity min. 1.0 ton per 1
0or180
J2 AXISJ3 AXISJ4 AXISJ5 AXISJ6 AXIS
ROBOT POSTURE ON TRANSPORATION
J1 AXIS-60
0
0
0
0
NOTICE
See the list of specification for machine weight. Eyebolts complied with JISB 1168. Quantity Eyebolts 4 Sling 4
Fig 1.1 (l) Transportation using a crane (R-2000iB/175L)
-
1.TRANSPORTATION AND INSTALLATION B-82234EN/07
- 16 -
NOTICE
See the lisf of specification for machine weight. Eyebolts complied with JISB 1168. Quantity Eyebolts 4 Sling 4
0or180
J2 AXISJ3 AXISJ4 AXISJ5 AXIS
ROBOT POSTURE ON TRANSPORTATION
J1 AXIS-60
0
0
0
CraneCapacity min.2.5 ton
SlingCapacity min.1.0 ton per 1
317 305
1575
.5
1590
348477
Center ofgravity
Eyebolt(M20)Install to the out taps
Fig 1.1 (m) Transportation using a crane (R-2000iB/100H)
-
B-82234EN/07 1.TRANSPORTATION AND INSTALLATION
- 17 -
Center of gravity
ROBOT POSTURE ON TRANSPORTATION
0
000-550
J6 AXISJ5 AXISJ4 AXISJ3 AXISJ2 AXIS
485
Install to the out taps.Eyebolts(M20)
423348
1314
1040
J1 AXIS
Center of gravity
CraneCapacity min. 2.5 tonSlingCapacity min. 1.0 ton per 1
NOTICE
See the list of specification for machine weight. Eyebolts complied with JISB 1168. Quantity Eyebolts 4 Sling 4Be sure to place the cable protection plate to prevent the slings from compressing cables.
Fig 1.1(n) Transportation using a crane (R-2000iB/165CF)
-
1.TRANSPORTATION AND INSTALLATION B-82234EN/07
- 18 -
956
188
88
Center of gravity
Center ofgravity
ForkliftCapacity min. 2.0 ton*125L and 175L are 2.5 ton
NOTICE)
See the list of specifications for machine weight
Transport equipment 1OPTION
0or 180J2 AXISJ3 AXISJ4 AXISJ5 AXISJ6 AXIS
J1 AXIS -60 0 0 0 0
ROBOT POSTURE ON TRANSPORATION
Fig 1.1 (o) Transportation using a forklift (R-2000iB/165F,210F,125L, 175L J1 base type)
100
200
NOTICE)
1. See the list of specification for machine weight. 2. Do not spoil the head of the bolt when detaching it because LOCTITE is spread on the installation bolt.
Center ofgravity
Center ofgravity
Arbitrary
ForkliftCapacity min. 2.0 ton 125L and 175L are min. 2.5 ton
868
Transport equipment(OPTION)
J2 AXISJ3 AXISJ4 AXISJ5 AXISJ6 AXIS
ROBOT POSTURE ON TRANSPORTATION
J1 AXIS -60 0 0 0 0
Fig 1.1 (p) Transportation using a forklift (R-2000iB/165F,210F,125L,175L J1 base type)
CAUTION Exercise care to prevent the fork of the forklift from striking transport equipment strongly.
SchiltzALine
J2 base type
-
B-82234EN/07 1.TRANSPORTATION AND INSTALLATION
- 19 -
ForkliftCapacity min. 2.5 ton
Center ofgravity
1242
200
100
Transportequipment 3(option)
Center of gravity
0J2 AXISJ3 AXISJ4 AXISJ5 AXISJ6 AXIS
J1 AXIS-12040 0 0 0
ROBOT POSTURE ON TRANSPORATION
NOTICE
See the list of specification for machine weight.
Fig 1.1 (q) Transportation using a forklift (R-2000iB/165R J1 base type)
Forkliftcapacity. 2.5 ton
Center of gravity
1242
100
200
Transportequipment 3(OPTION)
Center ofgravity
0J2 AXISJ3 AXISJ4 AXISJ5 AXISJ6 AXIS
J1 AXIS-12040 0 0 0
ROBOT POSTURE ON TRANSPORATION
NOTICE
See the list of specification for machine weight.
Fig 1.1 (r) Transportation using a forklift (R-2000iB/200R J1 base type)
CAUTION Exercise care to prevent the fork of the forklift from striking transport equipment strongly.
-
1.TRANSPORTATION AND INSTALLATION B-82234EN/07
- 20 -
1242
100
200
Forkliftcapacity min. 2.5 ton
Center ofgravity
Center ofgravity
0J2 AXISJ3 AXISJ4 AXISJ5 AXISJ6 AXIS
J1 AXIS-12041 0 0 0
CraneCapacity min. 2.5 tonSlingCapacity min. 1.0 ton per 1
ROBOT POSTURE ON TRANSPORATION
NOTICE
See the list of specification for machine weight. Eyebolts complied with JISB 1168. Quantity Eyebolts 4 Sling 4
Transport equipment 3(OPTION)
Fig 1.1(s) Transportation using a forklift (R-2000iB/100P J1 base type)
ForkliftCapacitymin 2.5 ton
Center ofgravity Center of
gravity
200
100
1207
73600
465
NOTE). See the list of specification for machine weight.When you transport robot,please be sure to transport it by the posture for transporation.When you transport robot,remove all tools.. Be sure to remove transport equipment after you set robot up.
ArbitraryJ2 AXISJ3 AXISJ4 AXISJ5 AXISJ6 AXIS
ROBOT POSTURE ONTRANSPORTATIONJ1 AXIS
-12040 0 0 0
Transportepuipment (OPTION)
Fig 1.1 (t) Transportation using a forklift (R-2000iB/165R J2 base type)
CAUTION Exercise care to prevent the fork of the forklift from striking transport equipment strongly.
-
B-82234EN/07 1.TRANSPORTATION AND INSTALLATION
- 21 -
Forklift Capacity:min ton.
Center ofgravity Center of
gravity
1207
100
200
465 73
600
NOTE). See the list of specification for machine weight.When you transport robot,please be sure to transport it by the posture for transporation.When you transport robot,remove all tools.. Be sure to remove transport equipment after you set robot up.
ArbitraryJ2 AXISJ3 AXISJ4 AXISJ5 AXISJ6 AXIS
ROBOT POSTURE ONTRANSPORTATIONJ1 AXIS
-12040 0 0 0
Transport Fig 1.1 (u) Transportation using a forklift (R-2000iB/200R J2 base type)
ForkliftCapacitymin ton.
Center of gravity Center of
gravity
200
100
1207
465 73
600
NOTE). See the list of specification for machine weight.When you transport robot,please be sure to transport it by the posture for transporation.When you transport robot,remove all tools.. Be sure to remove transport equipment after you set robot up.
ArbitraryJ2 AXISJ3 AXISJ4 AXISJ5 AXISJ6 AXIS
ROBOT POSTURE ONTRANSPORTATIONJ1 AXIS
-12041 0 0 0
Transportequipment (OPTION)
Fig 1.1 (v) Transportation using a forklift (R-2000iB/100P J2 base type)
CAUTION Exercise care to prevent the fork of the forklift from striking transport equipment strongly.
-
1.TRANSPORTATION AND INSTALLATION B-82234EN/07
- 22 -
NOTE)
See the list of specification for machine weight.
0or 180
J2 AXISJ3 AXISJ4 AXISJ5 AXIS
J1 AXIS
0
0
0
-55
Center ofgravity
ROBOT POSTURE ON TRANSPORTATION
Forkliftcapacity 2.0 ton
Transport equipment(option)
188
88
956
Fig 1.1 (w) Transportation using a forklift (R-2000iB/170CF)
NOTE) See the list of the specification for machine weight.
0or 180
J2 AXISJ3 AXISJ4 AXISJ5 AXIS
ROBOT POSTURE ON TRANSPORTATIONJ1 AXIS
0
0
0
-60
188
88
956 Transport equipment(OPTION) Forklift
Capacitiy. min 2.0 ton
Center ofgravity
Fig 1.1 (x) Transportation using a forklift (R-2000iB/100H J1 base type)
CAUTION Exercise care to prevent the fork of the forklift from striking transport equipment strongly.
-
B-82234EN/07 1.TRANSPORTATION AND INSTALLATION
- 23 -
182
82
ForkliftCapacity min. 2.0 ton
868Transport equipment(OPTION)
J2 AXISJ3 AXISJ4 AXISJ5 AXIS
ROBOT POSTURE ON TRANSPORTATIONJ1 AXIS
0
0
0
-60
Arbitrary
Center ofgravity
NOTICE)
1. See the list of specification for machine weight. 2. Do not spoil the head of the bolt when detaching it because LOCTITE is spread on the installation bolt.
Fig 1.1 (y) Transportation using a forklift (R-2000iB/100H J2 base type)
ROBOT POSTURE ON TRANSPORTATION
ForkliftCapacity min. 2.0 ton
182956
82
NOTE) See the list of the specification for machine weight.
Centerof gravity
Center ofgravity
Transport equipment(OPTION)
-55
J6 AXISJ5 AXISJ4 AXISJ3 AXISJ2 AXISJ1 AXIS 0
0000
Fig 1.1 (z) Transportation using a forklift (R-2000iB/165CF)
CAUTION Exercise care to prevent the fork of the forklift from striking transport equipment strongly.
-
1.TRANSPORTATION AND INSTALLATION B-82234EN/07
- 24 -
1.1.1 Transportation with an End Effector Attached When transporting a robot with an end effector such as a welding gun or hand attached, secure the arm with wood. If the arm is not secured, the end effector may oscillate for a cause such as vibration during transportation, thus imposing a large impact load on the reducer of the robot and damaging the reducer at an earlier stage.
Woods
Pallet
Woods
Fig. 1.1.1(a) Example of securing the arm during transportation when an end effector is attached
-
B-82234EN/07 1.TRANSPORTATION AND INSTALLATION
- 25 -
If the user cannot prepare a material for securing the arm, an optional securing jig kit for transportation is available. Specification: A05B-1329-K011 (R-2000iB/165F, 210F, 125L, 100H, 150U) A05B-1329-K012 (R-2000iB/175L)
BASEBOLT M12X35 (3)CONICAL SPRING WASHER (3)
SUPPORTBOLT M12X25 (3)WASHER (3)
HOLDERBOLT M10X120 (2)
NOTE)
1) REGARDING J2-AXIS AND J3-AXIS ATTITUDE DURING TRANSPORTING, REFFER TO FOLLOWING TABLE.
2) SUPPORT MUST BE FIXED TO HOLDER BY USING 3 BOLTS.3) BOLTS MUST BE TIGHTENED WITH TIGHTEINING TORQUE 94Nm(9.6kgfm).
J2 J3
-60 -47 0
Fig. 1.1.1(b) Securing jig kit for transportation
-
1.TRANSPORTATION AND INSTALLATION B-82234EN/07
- 26 -
1.2 INSTALLATION Fig. 1.2 shows the robot base dimensions. Avoid placing any object in front of the robot on the mounting face to facilitate the installation of the mastering fixture.(Shaded portion) Please select one of the following three methods of installing the robot according to the customers use environment. The strength of the chemical anchor depends on the concrete strength. See the design guideline of the manufacturer for the execution of the chemical anchor and consider the safety ratio sufficiently before use. Fig. 1.2.1(d), Table 1.2.1(a), and Table 1.2.1(b) indicate the force and moment applied to the base plate at the time of emergency stop of the robot and indicate the stopping distance and time of the J1 through J3 axes moved and consumed from the pressing of the emergency stop button until the robot stops. Consider the strength of the installation face with the data taken into account.
NOTE For the R-2000iB/165R, 200R and 100P, the
mastering fixture is placed below the J1 base installation surface.
For fixing robot 8-24 through 38 facing depth 5
Rotation center of J1 axis
Mounting face
Mou
ntin
g fa
ce
Mou
ntin
g fa
ce
Front
For mounting transportation equipment or eyebolt 8-M20 through
Fig.1.2 Dimensions of the robot base
-
B-82234EN/07 1.TRANSPORTATION AND INSTALLATION
- 27 -
1.2.1 Installation method - Installation method I Fig. 1.2.1 (a) The floor plate is imbedded in concrete and fastened with twelve
M20 ( strength classification 4.8) chemical anchors. Also fasten the base plate to the robot base using eight M2065 bolts (strength classification 12.9). Next, position the robot, and weld the base plate to the floor plate. (Floor length is 10 to 15mm.)
( The base plate is prepared as the option.) - Installation method II Fig. 1.2.1 (b) The floor plate is not imbedded in concrete. The floor plate is
fastened at the twelve points with M20 chemical anchors (strength classification 4.8) and the inclination of the floor plate is adjusted with the four fixing screws. The robot is positioned with the robot base pushed against the three 20 parallel pins inserted into the base and the robot base is fastened on the floor plate with eight M20 x 65 bolts (strength classification 12.9).
- Installation method III Fig. 1.2.1(c) The installation method is generally the same as described above
except that the parallel pins for pushing the robot base are not used.
The following parts are required to install the robot. Common to methods I, II, and III
- Robot mounting bolts M20x65 (Strength classification 12.9) 8pcs - Chemical anchors M20 (Strength classification 4.8) 12pcs - Base plates Thickness 32t 4pcs - Floor plate Thickness 32t 1pcs Methods II and III - Fixing screws M20 Four - Nuts M20 Four Method II only - Parallel pins 20 Three
NOTE - When the robot is operated with a combination other than the above, it may be damaged. - Arrangements for installation work (such as welding
and anchoring) need to be made by customers.
-
1.TRANSPORTATION AND INSTALLATION B-82234EN/07
- 28 -
Fig. 1.2.1 (a) Installation method
-
B-82234EN/07 1.TRANSPORTATION AND INSTALLATION
- 29 -
Fig.1.2.1 (b) Installation method
-
1.TRANSPORTATION AND INSTALLATION B-82234EN/07
- 30 -
Fig. 1.2.1 (c) Installation method
-
B-82234EN/07 1.TRANSPORTATION AND INSTALLATION
- 31 -
Table1.2.1(a) Force and moment during emergency stop
Model Vertical moment MV [kNm(kgfm)]
Force in vertical direction
FV [kN(kgf)]
Horizontal moment
MH [kNm(kgfm)]
Force in horizontal direction
FH [kN(kgf)] R-2000iB/165F 62.72(6400) 37.24(3800) 24.50(2500) 26.46(2700) R-2000iB/210F 73.50(7500) 41.16(4200) 25.48(2600) 27.44(2800) R-2000iB/165R 75.46(7700) 39.20(4000) 25.48(2600) 28.42(2900) R-2000iB/200R 84.28(8600) 41.16(4200) 25.48(2600) 27.44(2800) R-2000iB/100P 77.42(7900) 38.22(3900) 25.48(2600) 26.46(2700) R-2000iB/170CF 37.24(3800 33.32(3400) 9.80(1000) 22.54(2300) R-2000iB/125L 61.74(6300) 35.28(3600) 24.50(2500) 25.48(2600) R-2000iB/175L 71.54(7300) 38.22 (3900) 25.48(2600) 26.46(2700) R-2000iB/100H 53.90(5500) 34.30(3500) 19.60(2000) 25.48(2600) R-2000iB/150U 63.70(6500) 36.26(3700) 23.52(2400) 26.46(2700) R-2000iB/165CF 31.36(3200) 29.40(3000) 17.64(1800) 17.64(1800)
Table1.2.1(b) Stopping time and distance when emergency stop
Model J1-axis J2-axis J3-axis
Stopping time [msec] 372 333 145 R-2000iB/165F
Stopping distance [deg] (rad) 22.2 (0.39) 15.0 (0.26) 7.5 (0.13)
Stopping time [msec] 335 271 151 R-2000iB/210F
Stopping distance [deg] (rad) 16.4 (0.29) 14.2 (0.25) 8.4 (0.15)
Stopping time [msec] 519 352 202 R-2000iB/165R
Stopping distance [deg] (rad) 26.8 (0.47) 15.3 (0.27) 8.5 (0.15)
Stopping time [msec] 483 267 169 R-2000iB/200R
Stopping distance [deg] (rad) 22.2 (0.39) 10.7 (0.19) 8.3 (0.14)
Stopping time [msec] 542 349 282 R-2000iB/100P
Stopping distance [deg] (rad) 30.2 (0.53) 15.9 (0.28) 13.1 (0.23)
Stopping time [msec] 448 203 135 R-2000iB/170CF
Stopping distance [deg] (rad) 26.6(0.46) 9.8(0.17) 8.0(0.13)
Stopping time [msec] 370 375 200 R-2000iB/125L
Stopping distance [deg] (rad) 20.5 (0.36) 18.7 (0.33) 9.0 (0.16)
Stopping time [msec] 380 403 210 R-2000iB/175L
Stopping distance [deg] (rad) 19.2 (0.34) 17.4 (0.30) 9.5 (0.17)
Stopping time [msec] 435 316 186 R-2000iB/100H
Stopping distance [deg] (rad) 29.2 (0.51) 16.6 (0.29) 11.2 (0.20)
Stopping time [msec] 359 246 177 R-2000iB/150U
Stopping distance [deg] (rad) 19.9(0.35) 7.9(0.14) 9.4(0.16)
Stopping time [msec] 300 231 140 R-2000iB/165CF
Stopping distance [deg] (rad) 17.4 (0.30) 10.2 (0.18) 8.2 (0.14)
override : 100%
Max payload, max speed and max inertia posture
-
1.TRANSPORTATION AND INSTALLATION B-82234EN/07
- 32 -
MH
MV
FH
FV
Fig. 1.2.1 (d) Force during emergency stop
-
B-82234EN/07 1.TRANSPORTATION AND INSTALLATION
- 33 -
1.3 MAINTENANCE AREA Fig. 1.3 (a) to (d) show the maintenance area of the mechanical unit. Be sure to leave enough room for the robot to be mastered. See Chapter 8 for the mastering.
500
1695
Mastering area
Maintenance are(mechanical unit)
arm length+ 200)
403
500
423 500
500
A
300
500
500 348
R-2000iB/165F : 1695mmR-2000iB/210F : 1715mmR-2000iB/125L : 1850mmR-2000iB/175L : 1915mmR-2000iB/100H : 1695mmR-2000iB/150U : 1695mm
Fig. 1.3 (a) Maintenance area (R-2000iB/165F, 210F, 125L, 175L, 100H, 150U)
-
1.TRANSPORTATION AND INSTALLATION B-82234EN/07
- 34 -
Fig 1.3(b) Mastering area (R-2000iB/165R, 200R, 100P)
Maintenance area (mechanical unit)
Mastering area
-
B-82234EN/07 1.TRANSPORTATION AND INSTALLATION
- 35 -
605
500
500
500 774 500
Maintenance area
Mastering area
1085
Fig 1.3(c) Mastering area (R-2000iB/170CF)
-
1.TRANSPORTATION AND INSTALLATION B-82234EN/07
- 36 -
605
500
500
Mastering area
Maintenance area(Mechanical unit)
500 783
500
550
550
930
Fig 1.3 (d) Maintenance area (R-2000iB/165CF)
-
B-82234EN/07 1.TRANSPORTATION AND INSTALLATION
- 37 -
1.4 INSTALLATION SPECIFICATIONS Table 1.4 shows the robot installation specifications.
Table 1.4 Installation specifications R-2000iB/165F Approx. 1170kg R-2000iB/210F Approx. 1240kg R-2000iB/165R Approx. 1480kg R-2000iB/200R Approx. 1540kg R-2000iB/100P Approx. 1560kg R-2000iB/170CF Approx. 800kg R-2000iB/125L Approx. 1190kg R-2000iB/175L Approx. 1260kg R-2000iB/100H Approx. 1150kg R-2000iB/165CF Approx. 1050kg
Weight of mechanical unit
R-2000iB/150U Approx. 1070kg Allowable ambient temperature 0 to 45 Allowable ambient humidity Usual : Less than 75RH
Short period (in one month)Max. 95RH or less (Condensation free)
Admosphere Free of corrosive gases (Lower Note) Vibration Less than 0.5G (4.9m/s2)
CAUTION Contact the service representative, if the robot is to be
used in an environment or a place subjected to severe vibrations, heavy dust, cutting oil splash and or other foreign substances.
If the robot is used especially in an adverse environment stated below, grease the balancer as required.
Dusty environment; for example, an application in which the robot is used to handle tiles or bricks. Environment full of spatters developed in spot welding; for example, an application in which welding spatters deposit and accumulate on and around the balancer
In addition, if the robot is used in a special environment stated below, use a robot jacket or some other means to protect the balancer support part (which joins with theJ2 arm and J2 base) and rod sliding part. Environment where glass abrasive powders and
others are used; for example, and application in which the robot or balancer is subjected to splashes of powders in handling and other operations during glass abrasion.
Environment where metal powders are used; for example, an application in which the robot or balancer is subjected to splashes of powders in handling and other operations during metal working.
-
2.CONNECTION WITH THE CONTROLLER B-82234EN/07
- 38 -
2 CONNECTION WITH THE CONTROLLER
-
B-82234EN/07 2.CONNECTION WITH THE CONTROLLER
- 39 -
2.1 CONNECTION WITH THE CONTROLLER The robot is connected with the controller (NC) via the power cable, the signal cable and the earth cable. Connect these cables to the connectors on the back of the base. For details on air and option cables, see Chapter 5.
CAUTION Before connecting the cables, be sure to turn off the
power.
Controller Robot
Power and signal cables
earth cables
Air
OptionPower cable
Signal cable
A
Detail A
Earth terminal
Fig. 2.1 Cable connection
-
3.BASIC SPECIFICATION B-82234EN/07
- 40 -
3 BASIC SPECIFICATIONS
-
B-82234EN/07 3.BASIC SPECIFICATION
- 41 -
3.1 ROBOT CONFIGURATION
AC servo motor (M5) For J5-axis
AC servo motor (M6)For J6-axis
AC servo motor (M4)For J4-axis
AC servo motor (M3)For J3-axis
AC servo motor (M1)For J1-axis
End effector mounting face
Wrist unit
J3-axis arm
J3-axis casing
J2-axis arm
AC servo motor (M2) for J2-axis
J2-axis unit
J1-axis unit
Balancer
J2
+
-
J1
+
-
J3
+
-
J4 +
- J5 J6
+ - - +
All axes are 0 asthis posture.
Fig. 3.1 (a) Mechanical unit configuration and each axes coordinates (R-2000iB/165F, 210F, 125L, 175L,150U) NOTE) There is no balancer for R-2000iB/150U
-
3.BASIC SPECIFICATION B-82234EN/07
- 42 -
0
Fig 3.1 (b) Mechanical unit configuration and each axes coordinates (R-2000iB/165R,200R,100P)
AC servo motor For J5-axis
AC servo motor For J6-axis
AC servo motorFor J4-axis AC servo motorFor J1-axis
J2-axis arm
J2-axis arm
J3-axis casing
J1-axis unit AC servo motorFor J2-axis
J2-axis unit
Wrist unit
J3-axis arm
End effector mounting face
All axes are at 0 in this attitude.
-
B-82234EN/07 3.BASIC SPECIFICATION
- 43 -
AC servo motor(M1)For J1-axis
J1-axis unit
AC servo motor(M2)For J2-axis
J2-axis unit
J2-axis arm
AC servo motor(M3)For J3-axis
AC servo motor(M6)For J6-axis
AC servo motor(M5)For J5-axis
AC servio motor(M4)For J4-axis
J3-axis casing
Wrist unitEnd effectormounting face
J3-axis arm
J1
J2 J3
J4J5
J6+
+
++
+
+
- --
--
-
Fig 3.1 (c) Mechanical unit configuration and each axes coordinates (R-2000iB/170CF)
All axes are at 0 in this attitude.
-
3.BASIC SPECIFICATION B-82234EN/07
- 44 -
End effector mounting face
J2-axis arm
J3-axis arm
J3 casing
AC servo motorFor J2-axis (M2)
J2-axis unit
J1-axis unit
Balancer
AC servo motorFor J1-axis (M1)
AC servo motorfor J3-axis (M3)
AC servo motorFor J5-axis(M5)
AC servo motorFor J4-axis (M4)
J1
J3
+
-
-
+
J2
+-
*All axes are 0as this posture.
+ -J4
J5+-
Fig 3.1 (d) Mechanical unit configuration and each axes coordinates (R-2000iB/100H)
-
B-82234EN/07 3.BASIC SPECIFICATION
- 45 -
Fig 3.1 (e) Mechanical unit configuration (R-2000iB/165CF)
AC servo motor For J5-axis
AC servo motorFor J6-axis
AC servo motorFor J4-axis
AC servo motorFor J3-axis
AC servo motorFor J1-axis
J3-axis casing Wrist unit End effector morning face
J2-axis arm
AC servo motor For J2-axis
J2-axis unit
J1-axis unit
-
3.BASIC SPECIFICATION B-82234EN/07
- 46 -
Specifications (1/4) R-2000iB/165F R-2000iB/210F
Upper limit 180( 3.14rad) 180( 3.14rad)Lower limit -180(-3.14rad) -180(-3.14rad)Upper limit 76( 1.32rad) 76( 1.32rad)Lower limit -60(-1.05rad) -60(-1.05rad)Upper limit 230( 4.01rad) 230( 4.01rad)Lower limit -132(-2.30rad) -132(-2.30rad)Upper limit 360( 6.28rad) 360( 6.28rad)Lower limit -360(-6.28rad) -360(-6.28rad)Upper limit 125( 2.18rad) 125( 2.18rad)Lower limit -125(-2.18rad) -125(-2.18rad)Upper limit 360( 6.28rad) 360( 6.28rad)Lower limit -360(-6.28rad) -360(-6.28rad)
110/s (1.92rad/s) 95/s (1.66rad/s)110/s (1.92rad/s) 90/s (1.57rad/s)110/s (1.92rad/s) 95/s (1.66rad/s)150/s (2.62rad/s) 120/s (2.09rad/s)150/s (2.62rad/s) 120/s (2.09rad/s)220/s (3.84rad/s) 190/s (3.32rad/s)
165kg 210kg25kg 25kg550kg 550kg
921Nm (94kgfm) 1333Nm (136kgfm)921Nm (94kgfm) 1333Nm (136kgfm)461Nm (47kgfm) 706Nm (72kgfm)NOTE 1) 78.4kgm2 NOTE1) 141.1kgm2
(800kgfcms2) (1440kgfcms2)NOTE 1) 117.6kgm2 NOTE 1) 225.4kgm2
(1200kgfcms2) (2300kgfcms2)NOTE 1) 78.4kgm2 NOTE 1) 141.1kgm2
(800kgfcms2) (1440kgfcms2)NOTE 1) 117.6kgm2 NOTE 1) 225.4kgm2
(1200kgfcms2) (2300kgfcms2)NOTE 1) 40.2kgm2 NOTE 1) 78.4kgm2
(410kgfcms2) (800kgfcms2)NOTE 1) 98kgm2 NOTE 1) 196kgm2
(1000kgfcms2) (2000kgfcms2)
0.2mm1170kg 1240kg
Acoustic noise level
71.3dBNOTEThis value is equivalent continuous A-weighted sound pressure levelwhich applied with ISO11201(EN31201).This value is measured withthe following conditions"- Maximum load and speed""- Operating mode is AUTO"
Weight of mechanical unit 1480kg
Installation environment
Ambient temperature0 to 45Ambient humidity Normally 75%RH or less No dew,nor frost allowed. Short time (within one month) 95%RHHeight Up to 1000 meters above the sea level required,noparticularprovision for attitudeVibration 0.5G(4.9m/s2) or less
Drive method Electric servo dirive by AC servo motorRepeatability 0.3mm
J6 40.2kgm2
(410kgfcms2)
Allowableload inertiaat wrist
J4 78.4kgm2
(800kgfcms2)
J5 78.4kgm2
(800kgfcms2)
Allowableload momentat wrist
J4 921Nm (94kgfm)J5 921Nm (94kgfm)J6 461Nm (47kgfm)
J6-axis 220/s (3.84rad/s)
Max.loadcapacity
At Wrist 165kgAt J3-axis arm 25kgAt J2-axis base 550kg
J4-axis 150/s (2.62rad/s)J5-axis 150/s (2.62rad/s)
J6-axis 360( 6.28rad)-360(-6.28rad)
Max.motionspeed
J1-axis 110/s (1.92rad/s)J2-axis 100/s (1.75rad/s)J3-axis 110/s (1.92rad/s)
J4-axis 360( 6.28rad)-360(-6.28rad)
J5-axis 125( 2.18rad)-125(-2.18rad)
Motion range
J1-axis 180( 3.14rad)-180(-3.14rad)
J2-axis 65(1.13rad)-120(-2.08rad)
J3-axis 270(4.69rad)-95(-1.65rad)
Controlled axis 6-axisJ1,J2,J3,J4,J5,J6Installation Floor mount Rack mount
R-2000iB/165RType Articulated type
Note 1) The allowable load in standard inertia mode is shown in upper half and the allowable load in high inertia
mode in lower half. For details, see Section 4.5 in the connection manual.
-
B-82234EN/07 3.BASIC SPECIFICATION
- 47 -
Specifications (2/4) R-2000iB/100P R-2000iB/170CF
)Upper limit 180( 3.14rad) 180( 3.14rad)Lower limit -180(-3.14rad) -180(-3.14rad)Upper limit 65( 1.13rad) 135( 2.35rad)Lower limit -120(-2.09rad) -55(-0.96rad)Upper limit 270( 4.71rad) 220( 3.84rad)Lower limit -95(-1.66rad) -112(-1.95rad)Upper limit 360( 6.28rad) 360( 6.28rad)Lower limit -360(-6.28rad) -360(-6.28rad)Upper limit 125( 2.18rad) 125( 2.18rad)Lower limit -125(-2.18rad) -125(-2.18rad)Upper limit 360( 6.28rad) 360( 6.28rad)Lower limit -360(-6.28rad) -360(-6.28rad)
110/s (1.92rad/s) 110/s (1.92rad/s)90/s (1.57rad/s) 110/s (1.92rad/s)110/s (1.92rad/s) 110/s (1.92rad/s)120/s (2.09rad/s) 150/s (2.62rad/s)120/s (2.09rad/s) 150/s (2.62rad/s)190/s (3.32rad/s) 220/s (3.84rad/s)
100kg 170kg25kg 25kg550kg 550kg
980Nm (100kgfm) 921Nm (94kgfm)980Nm (100kgfm) 921Nm (94kgfm)706Nm (72kgfm) 461Nm (47kgfm)
225.4kgm2 78.4kgm2
(2300kgfcms2) (800kgfcms2)225.4kgm2 78.4kgm2
(2300kgfcms2) (800kgfcms2)196kgm2 40.2kgm2
(2000kgfcms2) (410kgfcms2)
0.15mm1560kg 800kg
Acoustic noise level
71.3dBNOTEThis value is equivalent continuous A-weighted sound pressure levelwhich applied with ISO11201(EN31201).This value is measured withthe following conditions"- Maximum load and speed""- Operating mode is AUTO"
Weight of machine unit 1540kg
Installation environment
Ambient temperature0 to 45Ambient humidity Normally 75%RH or less No dew,nor frost allowed. Short time (within one month) 95%RHHeight Up to 1000 meters above the sea levelrequired,noparticular provision for attitude
Drive method Electric servo dirive by AC servo motorRepeatability 0.3mm
Allowableload inertiaat wrist
J4 141.1kgm2
(1440kgfcms2)
J5 141.1kgm2
(1440kgfcms2)
J6 78.4kgm2
(800kgfcms2)
Allowableload momentat wrist
J4 1333Nm (136kgfm)J5 1333Nm (136kgfm)J6 706Nm (72kgfm)
J6-axis 190/s (3.32rad/s)
Max.loadcapacity
At wrist 200kgAt J3-axis arm At J2-axis base 550kg
J4-axis 120/s (2.09rad/s)J5-axis 120/s (2.09rad/s)
J6-axis 360( 6.28rad)-360(-6.28rad)
Max.speed
J1-axis 90/s (1.57rad/s)J2-axis 85/s (1.48rad/s)J3-axis 95/s (1.66rad/s)
J4-axis 360( 6.28rad)-360(-6.28rad)
J5-axis 125( 2.18rad)-125(-2.18rad)
Motion range
J1-axis 180( 3.14rad)-180(-3.14rad)
J2-axis 65( 1.13rad)-120 (-2.09rad)
J3-axis 270(4.71rad)-95(-1.66rad)
Controlled axis 6-axesJ1,J2,J3,J4,J5,J6Installation Rack mount
R-2000iB/200RType Articulated type
Floor mount(or top mount)
-
3.BASIC SPECIFICATION B-82234EN/07
- 48 -
Specifications (3/4) R-2000iB/175L R-2000iB/100H
5-axes (J1,J2,J3,J4,J5)
Upper limit 180( 3.14rad) 180( 3.14rad)Lower limit -180(-3.14rad) -180(-3.14rad)Upper limit 76( 1.33rad) 76( 1.33rad)Lower limit -60(-1.05rad) -60(-1.05rad)Upper limit 230( 4.01rad) 230( 4.01rad)Lower limit -125.9(-2.20rad) -132(-2.30rad)Upper limit 360( 6.28rad) 125( 2.18rad)Lower limit -360(-6.28rad) -125(-2.18rad)Upper limit 125( 2.18rad) 360( 6.28rad)Lower limit -125(-2.18rad) -360(-6.28rad)Upper limit 360( 6.28rad) -Lower limit -360(-6.28rad) -
95/s (1.66rad/s) 130/s (2.27rad/s)90/s (1.57rad/s) 130/s (2.27rad/s)95/s (1.66rad/s) 130/s (2.27rad/s)
120/s (2.09rad/s) 170/s (2.97rad/s)120/s (2.09rad/s) 360/s (6.28rad/s)190/s (3.32rad/s) -
175kg 100kg20kg -550kg 550kg
1225Nm (125kgfm) 441Nm (45kgfm)1225Nm (125kgfm) 245Nm (25kgfm)706Nm (72kgfm) -
225.4kgm2 39.2kgm2
(2300kgfcms2) (400kgfcms2)225.4kgm2 15.7kgm2
(2300kgfcms2) (160kgfcms2)196kgm2
(2000kgfcms2)
0.3mm 0.2mm1260kg 1150kg
Acoustic noise level
71.3dBNOTEThis value is equivalent continuous A-weighted sound pressure levelwhich applied with ISO11201(EN31201).This value is measured withthe following conditions"- Maximum load and speed""- Operating mode is AUTO"
Installation environment Ambient temperature0 to 45Ambient humidity Normally 75%RH or less No dew,nor frost allowed. Short time (within one month) 95%RHHeight Up to 1000 meters above the sea levelrequired,noparticular provision for attitu
Repeatability 0.2mmWeight of machine unit 1190kg
-(230kgfcms2)
Drive method Electric servo dirive by AC servo motor
Allowableload
inertia atwrist
J4 58.8kgm2
(600kgfcms2)
J5 58.8kgm2
(600kgfcms2)
J6 22.5kgm2
Allowableload momentat wrist
J4 588Nm (60kgfm)J5 588Nm (60kgfm)J6 343Nm (35kgfm)
J6-axis 260/s (4.54rad/s)Max.loadcapacity
At wrist 125kgAt J3-axis arm 20kgAt J2-axis base 550kg
J4-axis 170/s (2.97rad/s)J5-axis 170/s (2.97rad/s)
J6-axis 360( 6.28rad)-360(-6.28rad)
Max.speed J1-axis 110/s (1.92rad/s)J2-axis 110/s (1.92rad/s)J3-axis 110/s (1.92rad/s)
J4-axis 360( 6.28rad)-360(-6.28rad)
J5-axis 125( 2.18rad)-125(-2.18rad)
Motionrange
J1-axis 180( 3.14rad)-180(-3.14rad)
J2-axis 76( 1.33rad)-60 (-1.05rad)
J3-axis 230(4.01rad)-122.5(-2.14rad)
Controlled axis 6-axesJ1,J2,J3,J4,J5,J6Installation Floor mount
R-2000iB/125LType Articulated type
-
B-82234EN/07 3.BASIC SPECIFICATION
- 49 -
Specifications (4/4) R-2000iB/150U R-2000iB/165CF
Ungle mount Floor mountUpper limit 180( 3.14rad) 180( 3.14rad)Lower limit -180(-3.14rad) -180(-3.14rad)Upper limit 76( 1.33rad) 110( 1.92rad)Lower limit -60 (-1.05rad) -55 (-0.96rad)Upper limit 230(4.01rad) 120(2.09rad)Lower limit -132(-2.30rad) -130(-2.27rad)Upper limit 360( 6.28rad) 360( 6.28rad)Lower limit -360(-6.28rad) -360(-6.28rad)Upper limit 125( 2.18rad) 125( 2.18rad)Lower limit -125(-2.18rad) -125(-2.18rad)Upper limit 360( 6.28rad) 360( 6.28rad)Lower limit -360(-6.28rad) -360(-6.28rad)
110/s (1.92rad/s) 110/s (1.92rad/s)85/s (1.48rad/s) 90/s (1.57rad/s)110/s (1.92rad/s) 100/s (1.75rad/s)150/s (2.62rad/s) 130/s (2.27rad/s)150/s (2.62rad/s) 130/s (2.27rad/s)220/s (3.84rad/s) 210/s (3.67rad/s)
150kg 165kg10kg 25kg550kg 550kg
833Nm (85kgfm) 911Nm (93kgfm)833Nm (85kgfm) 911Nm (93kgfm)421Nm (43kgfm) 451Nm (46kgfm)
78.4kgm2 88.2kgm2
(800kgfcms2) (900kgfcms2) 78.4kgm2 88.2kgm2
(800kgfcms2) (900kgfcms2) 40.2kgm2 44.1kgm2
(410kgfcms2) (450kgfcms2)
0.2mm 0.15mm1070kg 1050kg
71.3 78.1dB
"- Maximum load and speed""- Operating mode is AUTO"
Installation environment
Ambient temperature0 to 45Ambient humidity Normally 75%RH or less No dew,nor frost allowed. Short time (within one month) 95%RHHeight Up to 1000 meters above the sea level required,noparticularprovision for attitudeVibration 0.5G(4.9m/s2) or less
Acoustic noise levelNOTEThis value is equivalent continuous A-weighted sound pressure levelwhich applied with ISO11201(EN31201).This value is measured withthe following conditions
Drive method Electric servo dirive by AC servo motorRepeatability
Weight of machine unit
Allowableload capacityat wrist
J4
J5
J6
Allowableload capacityat wrist
J4J5J6
Max.loadcapacity
At wristAt J3-axis armAt J2-axis base
Max motionspeed
J1-axisJ2-axisJ3-axisJ4-axisJ5-axisJ6-axis
Installation
Motion range
J1-axis
J2-axis
J3-axis
J4-axis
J5-axis
J6-axis
Type Articulated typeControlled axis 6-axesJ1,J2,J3,J4,J5,J6
Angle mount
-
3.BASIC SPECIFICATION B-82234EN/07
- 50 -
3.2 MECHANICAL UNIT OPERATION AREA AND INTERFERENCE AREA
Fig. 3.2 (a) to (j) show the robot interference area. When installing peripheral devices, be careful to clear away any objects that are the robot and the robots motion path in normal operation.
J3-axis rear side interference area
J5-axis rotation center
Motion range of J5-axis rotation center
Fig. 3.2 (a) Interference area (R-2000iB/165F)
-
B-82234EN/07 3.BASIC SPECIFICATION
- 51 -
J3-axis rear side interference area
J5-axisrotationcenter
Motion range of J5-axis rotation center
Fig. 3.2 (b) Interference area (R-2000iB/210F)
-
3.BASIC SPECIFICATION B-82234EN/07
- 52 -
Fig 3.2 (c) Interference area (R-2000iB/165R)
J3-axis rear side interference area
J5-axisrotationcenter
Motion range of J5-axis rotation center
-
B-82234EN/07 3.BASIC SPECIFICATION
- 53 -
Fig 3.2 (d) Interference area (R-2000iB/200R)
J3-axis rear side interference area
J5-axisrotation center
Motion range of J5-axis rotation center
-
3.BASIC SPECIFICATION B-82234EN/07
- 54 -
Fig 3.2 (e) Interference area (R-2000iB/100P)
-
B-82234EN/07 3.BASIC SPECIFICATION
- 55 -
(+109,+833)
R 1520
(+300,+1720)
(+689,-559)
(0,0)
(+1520,+500)(-488,+546)(-731,+480)
(-635,+423)(+600,+260)
(-821,+815)
0 DEG+180DEG
-180DEG
Motion range ofJ5-axis rotationcenter
J5-axis rotation center
(+600,-553)
300 670
500
550
326REAR SIDEINTERFERENCE AREA
215
98
210
220
112
55
180
30
252.
5
Fig. 3.2 (f) Interference area (R-2000iB/170CF)
-
3.BASIC SPECIFICATION B-82234EN/07
- 56 -
J3-axis rear side interference area
J5-axis rotation center
Motion range of J5-axis rotation center
Fig. 3.2 (g) Interference area (R-2000iB/125L)
-
B-82234EN/07 3.BASIC SPECIFICATION
- 57 -
Fig. 3.2 (h) Interference area (R-2000iB/175L)
-
3.BASIC SPECIFICATION B-82234EN/07
- 58 -
R 582
(+2655,+930)
R 2655
(+312,+3045)
(+1355,-370)
(0,0)
(+665,+337)
(+665,+1004)
(+445,+1953)
(-955,+425)
(-1099,+305)(-1538,+289)
(-1919,+1208)
1280
312
670
0 DEG.+180DEG.
-180DEG.
MOTION RANGEOF J4 AXISROTATION CENTER
J4-axis rotation center
1075
225
814
REAR SIDEINTERFERENCE AREA
(+665,-171)
-132 DEG
.
-10
DEG
.
76 DEG.
-60 DEG
.
-35 DEG
.
230 DEG.
215 DEG.
252.
5
215
Fig. 3.2 (i) Interference area (R-2000iB/100H)
-
B-82234EN/07 3.BASIC SPECIFICATION
- 59 -
R534
R 2655
J5-axis rotation center
J3-axis rear sideinterference area
(+2655,+930)
(+312,+3045)
(+1355,-370)
(0,0)
(+665,+337)
(+665,+1004)
(+445,+1953)
(-955,+425)
(-1099,+305)
(-1538,+289)
(-1919,+1208)
(+665,-171)
-132 DEG
.
230 DEG.
-60 DEG.
-30 DEG.
76 DEG.22
5
0 DEG.
+180DEG.
-180DEG.
252
670
J5
215 DEG.
(-1520,+1891)(+2162,+2160)
(-1495,+290)
(+1980,-209)-1
0 D
EG
16462260
670
1075
1280215
814312
THE ROBOT MAY NOT RESTDEPENDING ON ITS LOAD CONDITION AND POSTURE
THE ROBOT MAY NOT RESTDEPENDING ON ITS LOAD CONDITION AND POSTURE
Fig. 3.2 (j) Interference area (R-2000iB/150U)
-
3.BASIC SPECIFICATION B-82234EN/07
- 60 -
Fig. 3.2 (k) Interference area (R-2000iB/165CF)
-
B-82234EN/07 3.BASIC SPECIFICATION
- 61 -
3.3 ZERO POINT POSITION AND MOTION LIMIT Zero point and software motion limit are provided for each controlled axis. The robot cannot exceed the software motion limit unless there is a failure of the system causing loss of zero point position or there is a system error. Exceeding the software motion limit of a controlled axis is called overtravel (OT). Overtravel is detected at both ends of the motion limit for each axis. In addition, the motion range limit by a mechanical stopper or limit switch is also prepared to improve safety. Fig.3.3 (a) to (i) show the zero point and motion limit, LS detection position, and mechanical stopper position of each axis. * The motion range can be changed. For information on how to change the motion range, see Chapter 6, "AXIS LIMIT SETUP".
-184 Stopper end
-180.5 Limit switch detection position
180 Stroke end
+184 Stopper end
+180.5 Limit switch detection position
(NOTE) The limit switch of J1-axis is an option.
Fig. 3.3 (a) J1-axis motion limit
-
3.BASIC SPECIFICATION B-82234EN/07
- 62 -
Fig. 3.3 (b) J2-axis motion limit (R-2000iB/165F, 210F, 125L, 175L, 100H)
-120Stroke end (LOWER limit)
-120.5Limit switch detection position
-124Stopper end
+65Stoke end (Upper limit)
+65.5Limit switch detection position
+69Stopper end
(NOTE) The limit switch of J2-axis is an option. Motion limit is restricted by the position of the J3-axis.
Fig 3.3 (c) J2-axis motion limit (R-2000iB/165R,200R,100P)
-60.5 Limit switch detection position
+76 Stroke end (Upper limit)
+80 Stopper end
+76.5 Limit switch detection position
(NOTE) The limit switch of J2-axis is an option. Motion limit is restricted by the position of the J3-axis.
-60 Stroke end (Lower limit)
-64 Stopper end
-
B-82234EN/07 3.BASIC SPECIFICATION
- 63 -
+135vStroke end(Upper limit)
+139vStopper end
-55vStroke end(Lower limit)
-59vStopper end
135
055
Fig.3.3 (d) J2-axis motion limit (R-2000iB/170CF)
Fig.3.3 (e) J2-axis motion limit (R-2000iB/165CF)
-55 Stroke end (Lower Limit)
-55.5 Limit switch detection position
+110 Stroke end (Upper Limit)
+110.5 Limit switch detection position
+114 Stroke end
-59 Stopper end
(NOTE) The limit switch of J2-axis is an option. Motion limit is restricted by the position of the J3-axis.
-
3.BASIC SPECIFICATION B-82234EN/07
- 64 -
Limit switch detection position
Stroke end (Upper limit)
Stopper end
Stroke end (Lower limit)
(NOTE) The limit switch of J3-axis is an option. Motion limit is restricted by the position of the J2-axis.
Stopper end
Limit switch detection position
Fig. 3.3 (f) J3-axis motion limit (R-2000iB/165F, 210F, 165R, 200R, 100P, 125L, 175L, 100H)
55
0
J2+J3=-55vStroke end(Lower limit)
J2+J3=-59vStopper end
J2+J3=239vStopper end
J2+J3=235vStroke end(Upper limit)
0
125
235
Fig. 3.3 (g) J3-axis motion limit (R-2000iB/170CF)
-
B-82234EN/07 3.BASIC SPECIFICATION
- 65 -
Fig. 3.3 (h) J3-axis motion limit (R-2000iB/165CF)
Stopper end
+125Stroke end (Upper limit) +125Stopper (R-2000iB/165CF)
Stopper end
Stroke end (Lower limit)
(Except for R-2000iB/165CF)
(Except for R-2000iB/165CF)
Stopper end (for R-2000iB/165CF)
Fig. 3.3 (i) J5-axis motion limit (It is J4-axis for R-2000iB/100H)
(NOTE) The limit switch of J3-axis is an option. Motion limit is restricted by the position of the J2-axis.
Stopper end
Stopper end (Lower limit)
Limit switch detection position
Stroke end (Upper limit)
Stopper end
Limit switch detection position
-
3.BASIC SPECIFICATION B-82234EN/07
- 66 -
(NOTE) J4-axis does not have the limit switch and the mechanical stopper.
(NOTE)J6-axis does not have the limit switch and the mechanical stopper.
Software restriction
Software restriction
Fig. 3.3 (j) J4-axis motion limit Fig. 3.3 (k) J6-axis motion limit (for R-2000iB/100H is not included) (It is J5-axis for R-2000iB/100H)
-
B-82234EN/07 3.BASIC SPECIFICATION
- 67 -
3.4 WRIST LOAD CONDITIONS Fig. 3.4 (a) to (t) are diagrams to limit loads applied to the wrist. Apply a load within the region indicated in the graph.Apply the conditions of the allowable load moment and the allowable load inertia. See Section 3.1 about the allowable load moment and the allowable load inertia.
28.5
33.8170kg(R-2000iB/170CF)
35.2
44.3
37.8
35.5
47.3
51.7
62.6
X, Y [cm]
Z [cm]
27.7
6050
top related