ppt on spv module and emt

APresentation

On Solar Photo Voltaic Modules

&Electronic Milk Tester

AtRajasthan Electronics & Instruments Limited

(Kanakpura , Jaipur)

Submitted byPradeep Kumar kumawat

31-8-2015 1

Contents

Introduction about REIL Solar Photo Voltaic Module (i) Working Principle (ii) Block Diagram (iii) Manufacturing Process of SPV Module (iv) Advantages & Disadvantages Electronics Milk Tester (i) Working Principle (ii) Features of EMT Conclusion

31-8-2015 2

Introduction About REIL

REIL was established in 1981. It has an important place among the Electronic Industry Of

Rajasthan. It is a Public Sector Unit. It is a joint venture between Gov. of India And Gov. of

Rajasthan. Shareholding Pattern 1) Gov. of India 51% Holding 2) Gov. of Rajasthan 49% Holding

31-8-2015 3

Solar Photo Voltaic Module

SPV module is used to convert sun light into electrical energy. It has connected assembly of solar cells. Cells are made up of silicon. Output Of each cell is approximately 0.5 volt dc.

SPV Module

31-8-2015 4

Working Principle

It is based on the principle of Photoelectric Effect.

31-8-2015 5

Block Diagram

31-8-2015 6

Manufacturing Process Of SPV Module

Tabbing Of Cells Row Making Stringing Lay- Up Lamination Curing Trimming Channeling

31-8-2015 7

1. Tabbing of cells

Process of making terminals of a Bare cell by soldering copper strips to the Bus bar.

31-8-2015 8

2. Row making

A row of cells is made by connecting positive surfaces of one cell to the negative surface of another cell.

31-8-2015 9

3. Stringing

The rows of SPV cells are connected in series to get desired power rating.

31-8-2015 10

4. Lay-Up

It is a process of placing laminating material to the either side of the string. The laminating materials are-

(i) Top Glass (Toughened Glass) (ii) Ethylene Vinyl Acetate sheet (iii) Polyester Taddler

5. Lamination

The SPV module after lay-up process is placed in the laminator for 11 minutes.

31-8-2015 11

6.Curing

In this process the laminating material attain full strength by placing the module into 1200c temperature for 20 minutes.

7.Trimming

The final module is obtained by cutting the extra laminating material.

31-8-2015 12

8.Channeling

Modules are channelled from all the four sides. Anodized aluminium frames are used for channelling. Channels prevent any damage to the module.

31-8-2015 13

Advantages

It have no moving parts. No noise pollution or any othe type of pollution. Requires minimum maintenance. Have long service lifetimes (upto 20 years).

31-8-2015 14

Disadvantages

High cost. Doesn’t work at night. Efficiency levels are low.

31-8-2015 15

Electronic Milk Tester

It is an instrument which is used for the measurement of fat percentage in milk.

31-8-2015 16

Working Principle

It works on the photometric measurement of light scattered by the fat globules present in the milk sample.

31-8-2015 17

Features of EMT

Operate on AC mains as well as battery. Performs 110-130 samples per hour. Instant measurement and display of milk fat. Instant calculation of amount payable. Printing facility.

31-8-2015 18

Conclusion

This training made me learn the practical aspects of engineering.It gave me experience of working in a professional environment with professional people at a professional place. I have learnt adjusting myself to the busy schedule and workload which I will have to face in the future.

31-8-2015 19

Thank You

31-8-2015 20