overview cpma
Post on 17-Jan-2016
46 Views
Preview:
DESCRIPTION
TRANSCRIPT
Copyright VW AG
Workshop manual ElsaPro transaction no.: 33904
DMS order no.: undefined
VIN: WAUZZZ8R7AA096061 Model year: 2010Sales code: 8RB059 Model description: Q5 quat2.0 I4132 M6SEngine code: CDNB Gearbox code: KXROfficial licence plate number: Final drive code: Username: Calin Service advisor name: Calin, Murgu (RO101050.009)
Overview of fitting locations - injection system (CPMA)
Components A to I are not shown in the overview.
Page 1 of 18Overview of fitting locations - injection system (CPMA)
28.02.2013https://portal.cpn.vwg/elsapro/elsaweb/ctr/RMContentAction?docId=59548900&levelCo...
1 - Air mass meter -G70-
� Removing and installing → Chapter
2 - Lambda probe -G39- and Lambda probe heater -Z19-
� Fitting location → Fig.
� Removing and installing → Chapter
3 - Electrical connector for Lambda probe -G39-
� Fitting location → Fig.
4 - Lambda probe after catalytic converter -G130- and Lambda probe heater 1 after catalytic converter -Z29-
� Fitting location → Fig.
� Removing and installing → Chapter
Page 2 of 18Overview of fitting locations - injection system (CPMA)
28.02.2013https://portal.cpn.vwg/elsapro/elsaweb/ctr/RMContentAction?docId=59548900&levelCo...
5 - Fuel pressure regulating valve -N276-
� Fitting location → Fig.
6 - High-pressure pump
� Fitting location → Fig.
� Removing and installing → Chapter
7 - Fuel pressure sender for low pressure -G410-
� Fitting location → Fig.
8 - Vacuum unit for air flow control flaps (intake manifold flaps)
� Fitting location → Fig.
9 - Intake manifold flap valve -N316-
� Fitting location → Fig.
10 - Engine speed sender -G28-
� Fitting location → Fig.
� Removing and installing → Chapter
� 4.5 Nm
11 - Activated charcoal filter solenoid valve 1 -N80-
� Fitting location → Fig.
12 - 6-pin connector
� Lambda probe after catalytic converter -G130- and Lambda probe heater 1 after catalytic converter -Z29-
� Fitting location → Fig.
13 - Electrical connectors
� For knock sensor 1 -G61-, intake manifold flap valve -N316-, fuel pressure sender -G247-, intake manifold flap potentiometer -G336-, coolant temperature sender -G62-, Hall sender -G40- and injectors N30...N33
� Fitting location → Fig.
14 - Throttle valve module -J338-, throttle valve drive (electric throttle operation) -G186-
� Throttle valve drive angle sender -G187- and throttle valve drive angle sender 2 -G188-
� Throttle valve module -J338- must always be re-adapted to engine control unit -J623- after removal and installation or if it has been renewed
15 - Engine control unit -J623-
� Fitting location → Fig.
� Removing and installing → Chapter
16 - Charge pressure sender -G31-
� Fitting location → Fig.
� Removing and installing → Rep. gr.21
17 - Vacuum connection at intake manifold
18 - Cold-start valve -N17-
Page 3 of 18Overview of fitting locations - injection system (CPMA)
28.02.2013https://portal.cpn.vwg/elsapro/elsaweb/ctr/RMContentAction?docId=59548900&levelCo...
� Fitting location → Fig.
� Removing and installing → Chapter
19 - Knock sensor 1 -G61-
� To remove, first remove coolant pump with thermostat
� 20 Nm
� Removing and installing → Chapter
20 - Intake air temperature sender -G42-
21 - Coolant temperature sender -G62-
� Fitting location → Fig.
� Removing and installing → Rep. gr.19
22 - Valve for oil pressure control -N428-
� Fitting location → Fig.
� Removing and installing → Rep. gr.17
23 - Oil pressure switch for reduced oil pressure -F378-
� Fitting location → Fig.
� Removing and installing → Rep. gr.17
24 - Oil pressure switch -F22-
� Fitting location → Fig.
� Removing and installing → Rep. gr.17
25 - Fuel pressure sender -G247-
� Fitting location → Fig.
� Removing and installing → Chapter
26 - Intake manifold flap potentiometer -G336-
� Fitting location → Fig.
� After intake manifold has been renewed, intake manifold flap potentiometer -G336- must be adapted to engine control unit -J623-
27 - Camshaft control valve 1 -N205-
� Fitting location → Fig.
� Removing and installing → Rep. gr.15
28 - Hall sender -G40-
� Fitting location → Fig.
29 - Ignition coils with output stages
� Fitting location → Fig.
� Puller -T40039- is required for removing ignition coils from cylinder head.
� Removing and installing → Chapter
Page 4 of 18Overview of fitting locations - injection system (CPMA)
28.02.2013https://portal.cpn.vwg/elsapro/elsaweb/ctr/RMContentAction?docId=59548900&levelCo...
30 - Turbocharger air recirculation valve -N249-
� Located directly on turbocharger
� Removing and installing → Rep. gr.21
31 - Actuators for camshaft adjustment
� Actuator 1 for camshaft adjustment -F366-
� Actuator 2 for camshaft adjustment -F367-
� Actuator 3 for camshaft adjustment -F368-
� Actuator 4 for camshaft adjustment -F369-
� Actuator 5 for camshaft adjustment -F370-
� Actuator 6 for camshaft adjustment -F371-
� Actuator 7 for camshaft adjustment -F372-
� Actuator 8 for camshaft adjustment -F373-
� Fitting location → Fig.
� Removing and installing → Rep. gr.15
32 - Charge pressure control solenoid valve -N75-
� Located directly on turbocharger
� Removing and installing → Rep. gr.21
A - Fuel pump control unit -J538-
� Fitting location → Fig.
� Removing and installing → Rep. gr.20
B - Brake light switch - F- and brake pedal switch -F47-
� Fitting location → Fig.
� In footwell on brake pedal
� Removing and installing → Rep. gr.45
C - Clutch position sender -G476-
� Only fitted on vehicles with manual gearbox
� Fitting location → Fig.
D - Accelerator position sender -G79- and accelerator position sender 2 -G185-
� Fitting location → Fig.
� On accelerator pedal (both senders are accommodated in one housing)
� Removing and installing → Rep. gr.20
E - Radiator fan control unit -J293-
� Incorporated in radiator fan
F - Injectors
Page 5 of 18Overview of fitting locations - injection system (CPMA)
28.02.2013https://portal.cpn.vwg/elsapro/elsaweb/ctr/RMContentAction?docId=59548900&levelCo...
� Injector, cylinder 1 -N30-
� Injector, cylinder 2 -N31-
� Injector, cylinder 3 -N32-
� Injector, cylinder 4 -N33-
� Removing and installing → Chapter
G - Continued coolant circulation pump -V51-
� Not installed in all vehicles (only in vehicles for very hot countries)
� Removing and installing → Rep. gr.19
H - Left electrohydraulic engine mounting solenoid valve -N144-
� Not installed in all vehicles (depends on gearbox type)
I - Fuel quality sender -G446-
� Fitting location → Fig.
Engine control unit -J623-
Page 6 of 18Overview of fitting locations - injection system (CPMA)
28.02.2013https://portal.cpn.vwg/elsapro/elsaweb/ctr/RMContentAction?docId=59548900&levelCo...
Fuel pump control unit -J538--1-
Removing and installing → Rep. gr.20
Accelerator position sender -G79- and accelerator position sender 2 -G185-
2 - Electrical connector
Page 7 of 18Overview of fitting locations - injection system (CPMA)
28.02.2013https://portal.cpn.vwg/elsapro/elsaweb/ctr/RMContentAction?docId=59548900&levelCo...
Clutch position sender -G476--2-
Integrated functions: clutch pedal switch for engine start -F194- and clutch pedal switch -F36- (manual gearbox only)
1 - Brake light switch -F- and brake pedal switch -F47-
Oil pressure switch
1 - Electrical connector for oil pressure switch -F22-
2 - Oil pressure switch -F22-
3 - Oil pressure switch for reduced oil pressure -F378-
4 - Electrical connector for oil pressure switch for reduced oil pressure -F378-
Page 8 of 18Overview of fitting locations - injection system (CPMA)
28.02.2013https://portal.cpn.vwg/elsapro/elsaweb/ctr/RMContentAction?docId=59548900&levelCo...
Valve for oil pressure control -N428--3-
Ignition coils and actuators
1 - Fuel pressure sender for low pressure -G410-
2 - Ignition coil 1 with output stage -N70-
3 - Ignition coil 2 with output stage -N127-
4 - Ignition coil 3 with output stage -N291-
5 - Ignition coil 4 with output stage -N292-
6 - Electrical connector for Lambda probe -G39-
7 - Actuator 2 for camshaft adjustment -F367- (for cylinder No. 1)
8 - Actuator 1 for camshaft adjustment -F366- (for cylinder No. 1)
9 - Actuator 3 for camshaft adjustment -F368- (for cylinder No. 2)
10 - Actuator 4 for camshaft adjustment -F369- (for cylinder No. 2)
11 - Actuator 6 for camshaft adjustment -F371- (for cylinder No. 3)
12 - Actuator 5 for camshaft adjustment -F370- (for cylinder No. 3)
13 - Actuator 7 for camshaft adjustment -F372- (for cylinder No. 4)
14 - Actuator 8 for camshaft adjustment -F373- (for cylinder No. 4)
Page 9 of 18Overview of fitting locations - injection system (CPMA)
28.02.2013https://portal.cpn.vwg/elsapro/elsaweb/ctr/RMContentAction?docId=59548900&levelCo...
Fuel pressure sender -G247--1-
Intake manifold flap valve -N316--2-
1 - Vacuum unit for intake manifold flaps
Page 10 of 18Overview of fitting locations - injection system (CPMA)
28.02.2013https://portal.cpn.vwg/elsapro/elsaweb/ctr/RMContentAction?docId=59548900&levelCo...
Intake manifold flap potentiometer -G336--1-
Hall sender -G40--1-
Page 11 of 18Overview of fitting locations - injection system (CPMA)
28.02.2013https://portal.cpn.vwg/elsapro/elsaweb/ctr/RMContentAction?docId=59548900&levelCo...
Electrical connectors
1 - From activated charcoal filter solenoid valve 1 -N80-
2 - From knock sensor 1 -G61-
3 - (14-pin) from intake manifold flap valve -N316-, fuel pressure sender -G247-, intake manifold flap potentiometer -G336-, coolant temperature sender -G62- and Hall sender -G40-
4 - (8-pin) from injectors -N30-...-N33-
5 - From throttle valve module -J338-
6 - From intake air temperature sender -G42-
High-pressure pump
1 - Fuel pressure regulating valve -N276-
2 - High-pressure pump
- -Arrows- denote securing bolts
Page 12 of 18Overview of fitting locations - injection system (CPMA)
28.02.2013https://portal.cpn.vwg/elsapro/elsaweb/ctr/RMContentAction?docId=59548900&levelCo...
Fuel pressure sender for low pressure -G410--1-
Cold-start valve -N17--1-
Page 13 of 18Overview of fitting locations - injection system (CPMA)
28.02.2013https://portal.cpn.vwg/elsapro/elsaweb/ctr/RMContentAction?docId=59548900&levelCo...
Engine speed sender -G28--1-
Camshaft control valve 1 -N205--arrow-
Page 14 of 18Overview of fitting locations - injection system (CPMA)
28.02.2013https://portal.cpn.vwg/elsapro/elsaweb/ctr/RMContentAction?docId=59548900&levelCo...
Coolant temperature sender -G62--1-
Fitting location: below intake manifold in coolant pump
Charge pressure sender -G31--1-
Removing and installing → Rep. gr.21
Page 15 of 18Overview of fitting locations - injection system (CPMA)
28.02.2013https://portal.cpn.vwg/elsapro/elsaweb/ctr/RMContentAction?docId=59548900&levelCo...
Component and electrical connectors
1 - Activated charcoal filter solenoid valve 1 -N80-
2 - Lambda probe after catalytic converter -G130- and Lambda probe heater 1 after catalytic converter -Z29-
Lambda probes
1 - Lambda probe after catalytic converter -G130- and Lambda probe heater 1 after catalytic converter -Z29-
2 - Lambda probe -G39- and Lambda probe heater -Z19-
Page 16 of 18Overview of fitting locations - injection system (CPMA)
28.02.2013https://portal.cpn.vwg/elsapro/elsaweb/ctr/RMContentAction?docId=59548900&levelCo...
Components on turbocharger
1 - Turbocharger
2 - Vacuum unit for turbocharger; checking, adjusting, removing and installing → Rep. gr.21
3 - Charge pressure control solenoid valve -N75-
4 - Turbocharger air recirculation valve -N249- (note installation position, refer to next illustration)
For removing and installing components on turbocharger, refer to → Rep. gr.21.
Pay attention to installation position of turbocharger air recirculation valve -N249-
Page 17 of 18Overview of fitting locations - injection system (CPMA)
28.02.2013https://portal.cpn.vwg/elsapro/elsaweb/ctr/RMContentAction?docId=59548900&levelCo...
Fuel quality sender -G446--1-
Fitting location of fuel quality sender -G446-: on underbody, right-side (arrow points in direction of travel)
Page 18 of 18Overview of fitting locations - injection system (CPMA)
28.02.2013https://portal.cpn.vwg/elsapro/elsaweb/ctr/RMContentAction?docId=59548900&levelCo...
top related