murano task chair
Post on 12-Feb-2022
2 Views
Preview:
TRANSCRIPT
SUMMER 2010NOTE: Any alterations to listed components will void the manufacturer’s warranty. The manufacturer will not be responsible for any damage or bodily harm caused by alterations in accordance with national or local electrical codes and manufacturer’s specifications. In accordance with the manufacturer’s policy of continual product improvement, the product presented in this document is subject to change without notice or obligation.�
Global ContractMurano Chair Disassembly
Required Tools:
Note: Chair can be disassembled in 5 minutes or less
VERSION 2 03/18/10
Safety Glasses
Rubber Mallet
Hammer
Flathead Screw-driver
Actuator
Pliers
10 mm Hex Bit
Phillips Bit
T-25 Torx Bit
Bit Adaptor / Handle
Socket Wrench
13 mm Socket Adaptor
A
B
C D
E F
G B
8290MMurano Task Chair
GLOBALContract
A
B
C D
E F
G B
Global ContractMurano Chair Disassembly
Required Tools:
Note: Chair can be disassembled in 5 minutes or less
VERSION 2 03/18/10
Safety Glasses
Rubber Mallet
Flathead Screwdriver
Actuator
Pliers
10 mm Hex Bit
Phillips Bit
T-25 Torx Bit
Bit Adaptor / Handle
Socket Wrench
13 mm SocketAdaptor
Item# Description Qty Material
1 Base 1 Nylon or Alum.2 Cylinder (Gas Lift) 1 Metal, Plastic3 Casters 5 Nylon,Zinc4 Back 1 Nylon, Mesh, Metal5 Bolt 2 Metal6 Nut 2 Metal7 Seat Pan 1 Polypropylene8 Seat Foam 1 Foam9 Upholstery 1 Fabric10 Plug 5 Polypropylene11 Staples 50 Metal12 Arm 2 Polyurethane Foam, Nylon, Metal13 Lever 2 Nylon/Metal14 Plate 1 Metal15 Bolt 2 Metal16 Screw 2 Metal17 Mechanism 1 Metal/Nylon18 Cap 4 Nylon19 Screw 4 Metal20 Seat Slider 1 Polypropylene,Metal
Required Tools
A
B
C D
E F
G B
A
B
C D
E F
G B
A
B
C D
E F
G B
A
B
C D
E F
G B
Goggles Rubber Mallet Hammer
Global ContractMurano Chair Disassembly
Required Tools:
Note: Chair can be disassembled in 5 minutes or less
VERSION 2 03/18/10
Safety Glasses
Rubber Mallet
Flathead Screwdriver
Actuator
Pliers
10 mm Hex Bit
Phillips Bit
T-25 Torx Bit
Bit Adaptor / Handle
Socket Wrench
13 mm SocketAdaptor
Global ContractMurano Chair Disassembly
Required Tools:
Note: Chair can be disassembled in 5 minutes or less
VERSION 2 03/18/10
Safety Glasses
Rubber Mallet
Flathead Screwdriver
Actuator
Pliers
10 mm Hex Bit
Phillips Bit
T-25 Torx Bit
Bit Adaptor / Handle
Socket Wrench
13 mm SocketAdaptor
Global ContractMurano Chair Disassembly
Required Tools:
Note: Chair can be disassembled in 5 minutes or less
VERSION 2 03/18/10
Safety Glasses
Rubber Mallet
Flathead Screwdriver
Actuator
Pliers
10 mm Hex Bit
Phillips Bit
T-25 Torx Bit
Bit Adaptor / Handle
Socket Wrench
13 mm SocketAdaptor
Flathead Actuator PliersScrewdriver
Global ContractMurano Chair Disassembly
Required Tools:
Note: Chair can be disassembled in 5 minutes or less
VERSION 2 03/18/10
Safety Glasses
Rubber Mallet
Flathead Screwdriver
Actuator
Pliers
10 mm Hex Bit
Phillips Bit
T-25 Torx Bit
Bit Adaptor / Handle
Socket Wrench
13 mm SocketAdaptor
Global ContractMurano Chair Disassembly
Required Tools:
Note: Chair can be disassembled in 5 minutes or less
VERSION 2 03/18/10
Safety Glasses
Rubber Mallet
Flathead Screwdriver
Actuator
Pliers
10 mm Hex Bit
Phillips Bit
T-25 Torx Bit
Bit Adaptor / Handle
Socket Wrench
13 mm SocketAdaptor
Global ContractMurano Chair Disassembly
Required Tools:
Note: Chair can be disassembled in 5 minutes or less
VERSION 2 03/18/10
Safety Glasses
Rubber Mallet
Flathead Screwdriver
Actuator
Pliers
10 mm Hex Bit
Phillips Bit
T-25 Torx Bit
Bit Adaptor / Handle
Socket Wrench
13 mm SocketAdaptor
10mm Hex Bit Phillips Bit T-25 Torx Bit
Global ContractMurano Chair Disassembly
Required Tools:
Note: Chair can be disassembled in 5 minutes or less
VERSION 2 03/18/10
Safety Glasses
Rubber Mallet
Flathead Screwdriver
Actuator
Pliers
10 mm Hex Bit
Phillips Bit
T-25 Torx Bit
Bit Adaptor / Handle
Socket Wrench
13 mm SocketAdaptor
Global ContractMurano Chair Disassembly
Required Tools:
Note: Chair can be disassembled in 5 minutes or less
VERSION 2 03/18/10
Safety Glasses
Rubber Mallet
Flathead Screwdriver
Actuator
Pliers
10 mm Hex Bit
Phillips Bit
T-25 Torx Bit
Bit Adaptor / Handle
Socket Wrench
13 mm SocketAdaptor
Global ContractMurano Chair Disassembly
Required Tools:
Note: Chair can be disassembled in 5 minutes or less
VERSION 2 03/18/10
Safety Glasses
Rubber Mallet
Flathead Screwdriver
Actuator
Pliers
10 mm Hex Bit
Phillips Bit
T-25 Torx Bit
Bit Adaptor / Handle
Socket Wrench
13 mm SocketAdaptor
Bit Adaptor Socket Wrench 13 mm Socket /Handle Adapter
Global ContractMurano Chair Disassembly
Required Tools:
Note: Chair can be disassembled in 5 minutes or less
VERSION 2 03/18/10
Safety Glasses
Rubber Mallet
Flathead Screwdriver
Actuator
Pliers
10 mm Hex Bit
Phillips Bit
T-25 Torx Bit
Bit Adaptor / Handle
Socket Wrench
13 mm SocketAdaptor
Global ContractMurano Chair Disassembly
Required Tools:
Note: Chair can be disassembled in 5 minutes or less
VERSION 2 03/18/10
Safety Glasses
Rubber Mallet
Flathead Screwdriver
Actuator
Pliers
10 mm Hex Bit
Phillips Bit
T-25 Torx Bit
Bit Adaptor / Handle
Socket Wrench
13 mm SocketAdaptor
SUMMER 2010 NOTE: Any alterations to listed components will void the manufacturer’s warranty. The manufacturer will not be responsible for any damage or bodily harm caused by alterations in accordance with national or local electrical codes and manufacturer’s specifications. In accordance with the manufacturer’s policy of continual product improvement, the product presented in this document is subject to change without notice or obligation. �
Base/Gas Lift:
Back:
Upholstered Seat:
Arm:
Seat Slider:
Global ContractMurano Chair Disassembly
Arm Dissassembly:
1. Use 30 mm socket wrench adaptor to remove arm fastener. Repeat 2 times.
2. Use flathead or phillips screwdriver to remove arm bracket from seat slider. (2 screws must be removed)
MetalMetalMetalScrap or Reuse Scrap or Reuse
(2) (2) (1) (2) (2)
Bins for Components Removed
VERSION 2 03/18/10
Scrap or Reuse Scrap or Reuse
Global ContractMurano Chair Disassembly
Seat Slider and Mechanism Dissassembly:
1. Use the T-25 Torx Bit to remove the fasteners from the 4 slots in the seat slider. This will separate the seat slider from the mechanism.
MetalNylon
(4)(4)(1) (1)
Bins for Components Removed
VERSION 2 03/18/10
Global ContractMurano Chair Disassembly
Upholstered Seat Dissassembly:
1. Flip seat upside down. Use flathead screwdriver to loosen plastic plug. Repeat 5 times.
2. Use flathead screwdriver to pry apart and completely remove plastic plug from seat. Repeat 5 times.
3. Remove upholstered seat from seat slider by hand. 4. Use actuator to loosen staples in fabric.
VERSION 2 03/18/10
Global ContractMurano Chair Disassembly
Upholstered Seat Dissassembly (continued):
5. Use pliers to completely remove all staples and allow fabric to come loose.
6. Remove foam from plastic seat pan by hand.
Polypropylene PolypropyleneFoamFabric Metal
(1) (1) (1) (5) (25-75)
Bins for Components Removed
VERSION 2 03/18/10
Global ContractMurano Chair Disassembly
Back Dissassembly:
1. Flip chair upside down and remove 2 fasteners from the back frame using the AM-10 Bit.
Metal Metal
(1) (2) (2)
Bins for Components Removed
VERSION 2 03/18/10
Scrap or Reuse
Global ContractMurano Chair Disassembly
Base / Gas Lift Dissassembly:
1. Remove base by striking bottom side of gas lift with rubber mallet.
1. Remove casters from base by hand. Repeat 5 times.
3. Remove gas lift by striking mechanism with hammer.
Nylon or Aluminum
(1)
(1) (5)
Bins for Components Removed
VERSION 2 03/18/10
Scrap or Reuse
Scrap or Reuse
DISASSEMBLY INSTRUCTIONS
Product designed for disassembly in a reasonable time frame (5 minutes or less).
Base/Gas Lift:a. Remove base (1) by striking bottom side of gas lift cylinder with rubber mallet.b. Remove casters (3) from base, by hand.c. Remove gas lift (2) by striking mechanism with hammer.
Back:d. Flip chair upside down and remove 2 fasteners and nuts (5) and (6) from the back frame (4) using the AM- 10 bit.
Upholstered Seat:e. Flipseatupsidedown.Useflatheadscrewdriverto loosen plastic plug (10).f. Useflatheadscrewdrivertopryapartandcompletely remove plastic plug (10) from seat. Repeat 5 times.g. Remove upholstered seat from seat slider (20) by hand.h. Use actuator to loosen staples (11) in upholstery (9).i. Use pliers to completely remove all staples and allow fabric to come loose.j. Remove foam (8) from seat pan (7) by hand.
Arm:k. Use 30mm socket wrench adaptor to remove arm fastener (15). Repeat 2 times.l. UseflatheadorPhillipsscrewdrivertoremovearm plate (14) from seat slider (20). Must remove 2 screws (16).
Seat Slider:m. Use T-25 Torx Bit to remove the fasteners (19) and caps (18) from the 4 slots in the seat slider (20). Separate the seat slider from the mechanism (17).
Please contact your Global Contract Service Representa-
A
B
C D
E F
G B
A
B
C D
E F
G B
A
B
C D
E F
G B
A
B
C D
E F
G B
A
B
C D
E F
G B
8290MMurano Task Chair
GLOBALContract
A
B
C D
E F
G B
A
B
C D
E F
G B
A
B
C D
E F
G B
A
B
C D
E F
G B
A
B
C D
E F
G B
A
B
C D
E F
G B
A
B
C D
E F
G B
A
B
C D
E F
G B
A
B
C D
E F
G B
A
B
C D
E F
G B
A
B
C D
E F
G B
A
B
C D
E F
G B
A
B
C D
E F
G B
top related