minix780g series ver1.0
Post on 07-Apr-2018
242 Views
Preview:
TRANSCRIPT
-
8/6/2019 Minix780G Series Ver1.0
1/83
Rev: 1.00, July 2008P/N: 80ECM78010
User's Manual
Minix780G SeriesSocket AM2/AM2+ Processor Mainboard
Website: http://www.jwele.com
-
8/6/2019 Minix780G Series Ver1.0
2/83
Disclaimer The intellectual property of this manual belongs to our company. The ownership of all of theproducts, including accessories and software etc. belong to our company. No one is permitted tocopy, change, or translate without our written permission.We compiled this manual based on our careful attitude, but we can not guarantee the accuracy of the contents. This manual is purely technical documentation, without any hint or other meanings,
and we won't commit users' misunderstanding of the typesetting error.Our products are in continuous improvement and updating, Therefore, we retain the right that wewon't give notice to the users in future.
Copyright All of the trademark in this manual belong to their own registered company. All of the products name is only for identification, its title belongs to its manufacturer or brandowner.
-
8/6/2019 Minix780G Series Ver1.0
3/83
Table of Contents
Chapter 1 Introduction ............................................................................................ 41.1 Package Checklist ................................................................................................................4
1.2 Speci cations ......................................................................................................................51.3 Mainboard Layout ................................................. ......................................................... ......61.4 Connecting Rear Panel I/O Devices .......................................................... ............................. 7
Chapter 2 Hardware Setup ....................................................................................... 82.1 Choosing a Computer Chassis ....................................................... ........................................ 82.2 Installing Mainboard ............................................................................................................8
2.3 Installation of the CPU and CPU Cooler .................................................................................92.3.1 Installation of the CPU ...................................................................................................92.3.2 Installation of the CPU Cooler .................................................. ..................................... 10
2.4 Installation of Memory Modules .................................................... ...................................... 102.5 Connecting Peripheral Devices ...................................................... ...................................... 11
2.5.1 IDE Disk Drive Connectors ..................................................... ....................................... 112.5.2 Serial ATA Connectors ................................................. ................................................. 112.5.3 PCI Express slots .........................................................................................................11
Chapter 3 Jumpers & Headers Setup .......................................................................12Chapter 4 BIOS Setup Utility ...................................................................................174.1 About BIOS Setup ..............................................................................................................174.2 To Run BIOS Setup ......................................................... ................................................... 174.3 About CMOS ....................................................... .......................................................... ..... 174.4 The POST (Power On Self Test) .......................................................................................... 174.5 BIOS Setup CMOS Setup Utility .................................................. ..................................... 18
4.5.1 CMOS Setup Utility ..................................................... .................................................. 184.5.2 Control Keys .................................................. .......................................................... .... 204.5.3 Advanced Setting ....................................................... .................................................. 214.5.4 PCIPnP Setting ............................................................................................................254.5.5 Boot Setting ................................................................................................................264.5.6 Security Setting ...........................................................................................................284.5.7 JUSTw00T! Setting ..................................................... .................................................. 294.5.8 Power Setting ................................................. .......................................................... ... 334.5.9 Exit Setting .................................................................................................................35
Chapter 5 Driver Installation ...................................................................................39
.....................................................................................................41
-
8/6/2019 Minix780G Series Ver1.0
4/83
Minix780G Series User's Manual
- -
Chapter 1 Introduction
1.1 Package ChecklistThank you for choosing our product.Please check the following packing and accessories, if there is any broken or part missing,please contact with your franchiser.
HDD Cable X 1 Rear I/O Panel X 1
User's Manual X 1 Driver/Utility CD X 1 Serial ATA Signal Cable X 1 Serial ATA Power Cable X 1 (Optional)
The items listed above are for reference only, and are subject to change without notice.
-
8/6/2019 Minix780G Series Ver1.0
5/83
Minix780G Series User's Manual
- -
1.2 Speci cations
CPU
- Supports AMD Socket AM2+ / AM2 processors:- AMD Phenom / Athlon 64 FX / Athlon 64 X2 Dual Core / Athlon 64 /
Sempron- Hyper Transport Bus 5200/2000 MT/s (HT 3.0/1.0)- Note: The board can not support 125W TDP processors. For details , please
refer to the CPU support list on our homepage.
Main Chipset - AMD 780G + SB700
- Built in Radeon HD 3200 Graphics, DirectX 10 Ready
Main Memory
- Supports 2 x 1.8V DDR2 SODIMM sockets supporting up to 4 GB of
system memory- Supports Dual channel memory architecture- Onboard side-port DDR2 memory- Supports for DDR2 1066MHz/800MHz/667MHz memory modules
BIOS
- AMI BIOS, supports Plug&Play- Supports BIOS ROM Write Protect- Supports Advanced Power Management ACPI,STR - CPU temperature, Fan speed, System Voltage monitoring
Integrated Ports
- 1 x PS/2 Keyboard port
- 1 x DVI port- 1 x HDMI port- 1 x VGA port- 1 x RJ45 port- 1 x eSATA port- 1 x COM port- 1 x IR port- 10 x USB 2.0 ports, USB 1.1 is compliant- 4 x SATA ports , Maximum Speed to 3GB/s,support for SATA RAID 0,1,10- 1 x IDE connector, 2 x IDE devices could be connected,
Supports ATA 133/100/66/33
Sound - Onboard 6-channel/8-channel HD Audio Codec (Optional)- Front Panel Jumper, provides stereo MIC port on front panelOnboard LAN - Onboard 10/100/1000Mbps compatible LAN (Optional)Expansion Slots - 1 x PCI Express x4 slot(PCI Express 2.0)Form Factor Mini ITX (170mm*170mm)Remark - 1066 MHz memory support is dependent on the CPU being used
-
8/6/2019 Minix780G Series Ver1.0
6/83
Minix780G Series User's Manual
- -
1.3 Mainboard Layout
(This picture is only for reference)
-
8/6/2019 Minix780G Series Ver1.0
7/83
Minix780G Series User's Manual
- -
1.4 Connecting Rear Panel I/O Devices The rear I/O part of these mainboard provides the following I/O ports:
(This picture is only for reference)
PS/2 Keyboard: Connect to PS/2 keyboard. HDMI:Connects to multimedia devices of HDMI protocol. SPDIF IN:This connector provides an S/PDIF-IN connection. SPDIF OUT:Connects to digital audio device. DVI: Connects to monitor input.
VGA: Connects to monitor input. eSATA: Connect to peripherial SATA devices. LAN: Connects to Local Area Network. USB: Connects to USB devices such as scanner, digital speakers, monitor, mouse, keyboard,
hub, digital camera, joystick etc. AUDIO1:
Cen./Sub. (Center / Subwoofer): Connect to the center and subwoofer channel in the 7.1channel audio system.
R.L./R.R. (Rear Left / Rear Right): Connect to the rear left and rear right channel in the 7.1channel audio system.
S.L./S.R. (Surround Left / Surround Right): Connect to the surround left and surround rightchannel in the 7.1 channel audio system.
Line-In: Connects to the line out from external audio sources.Line-Out: Connects to the front left and front right channel in the 7.1-channel or regular
2-channel audio system.Mic-In: Connects to the plug from external microphone.
-
8/6/2019 Minix780G Series Ver1.0
8/83
Minix780G Series User's Manual
- -
Chapter 2 Hardware Setup
2.1 Choosing a Computer Chassis Choose a chassis big enough to install this mainboard. As some features for this mainboard are implemented by cabling connectors on the mainboard to indicators and switches or buttons on the chassis, make sure your chassis supports all the
features required. If there is possibility of adopting some more hard drives, make sure your chassis has suf cient
power and space for them. Most chassis have alternatives for I/O shield located at the rear panel. Make sure the I/O shield
of the chassis matches the I/O port con guration of this mainboard. You can nd an I/O shieldspeci cally designed for this mainboard in its package.
2.2 Installing MainboardMost computer chassis have a base with many mounting holes to allow the mainboard to besecurely attached, and at the same time, preventthe system from short circuits. There are two waysto attach the mainboard to the chassis base:(1)with studs, or (2) with spacers.Basically, the best way to attach the board is withstuds. Only if you are unable to do this should youattach the board with spacers. Line up the holes onthe board with the mounting holes on the chassis.If the holes line up and there are screw holes, youcan attach the board with studs. If the holes lineup and there are only slots, you can only attach with
spacers. Take the tip of the spacers and insert them into the slots. After doing this to all the slots,you can slide the board into position aligned with slots. After the board has been positioned,check to make sure everything is OK before putting the chassis back on.
To install this mainboard:1. Locate all the screw holes on the mainboard and the chassis base.2. Place all the studs or spacers needed on the chassis base and have them tightened.3. Face the mainboards I/O ports toward the chassiss rear panel.4. Line up all the mainboards screw holes with those studs or spacers on the chassis.
5. Install the mainboard with screws and have them tightened.
-
8/6/2019 Minix780G Series Ver1.0
9/83
Minix780G Series User's Manual
- -
2.3 Installation of the CPU and CPU CoolerBefore installing the CPU, please comply with the following conditions:1. Please make sure that the mainboard supports the CPU.2. Please take note of the one indented corner of the CPU. If you install the CPU in the wrong
direction, the CPU will not insert properly. If this occurs, please change the insert direction of the CPU.
3. Please add an even layer of heat sink paste between the CPU and CPU cooler.4. Please make sure the CPU cooler is installed on the CPU prior to system use, otherwise
overheating and permanent damage of the CPU may occur.5. Please set the CPU host frequency in accordance with the processor speci cations. It is not
recommended that the system bus frequency be set beyond hardware speci cations since itdoes not meet the required standards for the peripherals. If you wish to set the frequencybeyond the proper speci cations, please do so according to your hardware speci cationsincluding the CPU, graphics card, memory, hard drive, etc.
2.3.1 Installation of the CPU1. Unlock the socket by pressing the
lever sideways, then lift it up to a 90o
.2. Position the CPU above the socket such that
the CPU corner with the gold triangle matchesthe socket corner with a small triangle.
3. Carefully insert the CPU into the socket until it
ts place.
4. When the CPU is inplace, push down thesocket lever to securethe CPU.The lever clicks on theside tab to indicate thatit is locked.
Figure 1
Figure 2
Figure 3
-
8/6/2019 Minix780G Series Ver1.0
10/83
Minix780G Series User's Manual
- 10 -
2.3.2 Installation of the CPU CoolerFor proper installation, please kindly refer to the instruction manuals of your CPU Cooler.
2.4 Installation of Memory ModulesThis mainboard provides two 200-pin DDRII (Double Data Rate) SODIMM slots and supportsDual Channel Memory Technology. For dual channel con guration, you always need to install twoidentical (the same brand, speed, size and chip-type) memory modules in the DDRII DIMM slotsto activate Dual Channel Memory Technology. Otherwise, it will operate at single channel mode.
To install system memory:1. Power off the computer and unplug the
AC power cord before installing orremoving memory modules.
2. Locate the DIMM slot on the board.3. Insert the SODIMM module at a 45 degree
angle.4. Push the SODIMM module back towards the
board until the clips lock the module in place.5. To remove the DIMM modules, push the twoejector tabs on the slot outward simultaneously,and then pull out the DIMM module.
Static electricity can damage the electroniccomponents of the computer or optional boards.Before starting these procedures, ensure that youare discharged of static electricity by touching a
grounded metal object brie y.
1
2
3
We suggest there should be active cooling to the chipset area in order to let the motherboardfunction properly, completely enclosed system environment without adequate air ow will resultin chipset overheat, which is not recommended.
-
8/6/2019 Minix780G Series Ver1.0
11/83
Minix780G Series User's Manual
- 11 -
2.5 Connecting Peripheral Devices2.5.1 IDE Disk Drive Connectors
2.5.2 Serial ATA ConnectorsEach SATA connector serves as one single channel to connect one SATA device by SATA cable.
2.5.3 PCI Express slotsPCIE1 is for PCI Express X4 slot.
Each of the IDE port connects up to two IDEdrives at Ultra ATA 133/100/66/33 mode byone 40-pin, 80-conductor,and 3-connector Ultra
ATA/66 ribbon cables.Connect the single end (blue connector) at thelonger length of ribbon cable to the IDE port of this board, the other two ends (gray and black connector) at the shorter length of the ribboncable to the connectors of your hard drives.
Make sure to con gure the Master and Slave relationbefore connecting two drives by one single ribbon cable.The red line on the ribbon cable must be aligned withpin-1 on both the IDE port and the hard-drive connector.
-
8/6/2019 Minix780G Series Ver1.0
12/83
Minix780G Series User's Manual
- 12 -
Chapter 3 Jumpers & Headers Setup Quick Components Guide
NO. Layout Page NO. No. Layout Page NO.
1 JBAT 13 9 FUSB1/FUSB2 12 JDVI_HDMI 13 10 SPEAKER1 13 J5VDUAL 1 11 FPANEL 14 CFAN 1 12 IR1 15 SFAN1 1 13 JCOM1 16 SFAN2 1 14 J1 17 CD_IN 1 15 PWR12V 18 F_AUDIO 1 16 ATXPWR 1
1
2
3
4
5
67
8
9 10
11
12
13 14
15
16
-
8/6/2019 Minix780G Series Ver1.0
13/83
Minix780G Series User's Manual
- 13 -
Normal(Default )
Clear CMOS
J BAT o r C LR C MO S1_
1 2 3
1 2 3
Checking Jumper Settings For a 2-pin jumper, plug the jumper cap on both pins will make it CLOSE (SHORT). Remove the
jumper cap, or plug it on either pin (reserved for future use) will leave it at OPEN position. For 3-pin jumper, pin 1~2 or pin 2~3 can be shorted by plugging the jumper cap in.
How to identify the PIN1 jumpers?Please check the mainboard carefully, the PIN1 is marked by "1" or white thick line.
1-JBAT(CMOS Memory Clearing Header)The time to clear the CMOS memory occurs when (a) the CMOS data becomes corrupted, (b) youforgot the supervisor or user password preset in the BIOS menu, (c) you are unable to boot-upthe system because the CPU ratio/clock was incorrectly set in the BIOS menu, or (d) wheneverthere is modi cation on the CPU or memory modules.This header uses a jumper cap to clear the CMOSmemory and have it recon gured to the default valuesstored in BIOS. Pins 1 and 2 shorted (Default): Normal operation. Pins 2 and 3 shorted: Clear CMOS memory.
2-JDVI_HDMI(DVI/HDMI Setting Header)
1-2 Default AutoWhile JDVI_HDMI jumper be shorted#pin 1-2, it will auto detect HDMI orDVI device, but if some DVI or HDMIdevice cann't be detected, please beshorted #pin 2-3.
2-3 DVI/HDMI EN
-
8/6/2019 Minix780G Series Ver1.0
14/83
Minix780G Series User's Manual
- 1 -
3-J5VDUAL(5VDUAL Setting Header)
1-2 Default Enable 2-3 pin can not support the
keyboard post function,need toset 1~2 pin enable the function.2-3 Disable
4/5/6-CFAN/SFAN1/SFAN2(Fan Power Connectors) CFAN
Pin No. De nition1 GND
2 +12V
3 RPM
4 Control
SFAN1/SFAN2
Pin No. De nition1 GND2 +12V
3 RPM
7-CD_IN(Internal Audio Connectors)
8-F_AUDIO(Front Panel Audio Connection Header)Pin No. De nition Pin No. De nition
1 PROT1L 6 SENSE1_RETURN2 AGND 7 SENSE_SEND
3 PROT1R 8 NC4 PRESENCE# 9 PORT2L5 PORT2R 10 SENSE2_RETURN
These fan connectors are not jumpers.DO NOT place jumper caps on theseconnectors.
Pin No. De nition1 CD-L2 GND3 GND4 CD-R
-
8/6/2019 Minix780G Series Ver1.0
15/83
Minix780G Series User's Manual
- 1 -
9-FUSB1/FUSB2(Additional USB Port Headers)Pin No. De nition Pin No. De nition
1 VCC 2 VCC3 Data 0- 4 Data 1-5 Data 0+ 6 Data 1+7 Ground 8 Ground
10 NC
1
2
9
10
10/11-SPEAKER1/FPANEL(Speaker Headers & Front Panel Switches)
SPEAKER1:
Pin No. De nition1 SPK +2 NC3 NC4 SPK -
HDD_LED (Hard Driver LED Header)Connect the HDD LED cable to these PINs, in order to see the HDD statusRESET (Reset Control)This connector connects to the case-mounted reset switch for rebootingyour computer without having to turn off your power switch. This is apreferred method of rebooting in order to prolong the lift of the systems power supply.PWR-ON (Power Button)This connector connects to the case-mounted power switch to power ON/OFF the system.SPEAKER (Speaker)This 4-pin connector connects to the case-mountedspeaker. You should follow the instruction of thespeaker cable.
12-IR1(IR Connection Header)
Connect the IrDA cable (if available) to this IR connector.Pin No. De nition
1 VCC2 NC3 IRRX4 GND5 IRTX
-
8/6/2019 Minix780G Series Ver1.0
16/83
Minix780G Series User's Manual
- 1 -
13-JCOM1(Serial Port Header)This JCOM1 header supports a serial port module.Pin No. De nition Pin No. De nition
1 DCD 2 RXD3 TXD 4 DTR 5 GND 6 DSR 7 CTS 8 RTS9 RI
14-J1(Multifunctional device connecter) (Optional)The connecter may connect external multifunctional device, ,about detail connect way andde nition,please refer to external connect device's manual.
15/16-PWR12V/ATXPWR(4-pin 12V Power Connector/ATX 24-pin Power Connector)This mainboard provides two power connectors to connect power supplier.This connector allows you to connect an ATX 24-pin power supply.To connect the ATX 24-pinpower supply,make sure the plug of the power supply is inserted in the proper orientation and thepins are aligned. Then push down the power supply rmly into the connector.Your may use the 20-pin ATX power supply as you like.If you'd like to use the 20-pin ATX powersupply, please plug your power supply along with pin 1 & pin 13.
+ .++
+
+
+ ..
3 3V12V12V
5VSBPW R OK
COM5V
COM5VCOM3 3V
+3 3V
COM5V5V5V5V
COMCOM
COMPS ONCOM
12V3 3V
+++-
_
-+ .
1
12
13
24
-
8/6/2019 Minix780G Series Ver1.0
17/83
Minix780G Series User's Manual
- 1 -
Chapter 4 BIOS Setup UtilityBIOS stands for Basic Input and Output System. It was once called ROM BIOS when it was storedin a Read-Only Memory (ROM) chip. Now manufacturers would like to store BIOS in EEPROM whichmeans Electrically Erasable Programmable Memory. BIOS used in this series of mainboard is storedin EEPROM, and is the rst program to run when you turn on your computer.
BIOS performs the following functions:1. Initializing and testing hardware in your computer (a process called "POST", for Power On Self
Test).2. Loading and running your operating system.3. Helping your operating system and application programs manage your PC hardware by means of
a set of routines called BIOS Run-Time Service.
4.1 About BIOS SetupBIOS Setup is an interactive BIOS program that you need to run when:1. Changing the hardware of your system. (For example: installing a new Hard Disk etc.)2. Modifying the behavior of your computer. (For example: changing the system time or date, or
turning special features on or off etc.)
3. Enhancing your computer's behavior. (For example: speeding up performance by turning onshadowing or cache)
4.2 To Run BIOS SetupFirst access BIOS setup menu by pressing key after POST is complete (before OS isloaded). After the rst BIOS be setupped(or loaded default values) and save, the key willbe pressed if you will enter BIOS setup menu.
4.3 About CMOS
CMOS is the memory maintained by a battery. CMOS is used to store the BIOS settings you haveselected in BIOS Setup. CMOS also maintains the internal clock. Every time you turn on yourcomputer, the BIOS Looks into CMOS for the settings you have selected and con gures yourcomputer accordingly. If the battery runs out of power, the CMOS data will be lost and POST willissue a CMOS invalid or CMOS checksum invalid message. If this happens, you have to replacethe battery and check and con gure the BIOS Setup for the new start.
4.4 The POST (Power On Self Test)
POST is an acronym for Power On Self Test. This program will test all things the BIOS does
-
8/6/2019 Minix780G Series Ver1.0
18/83
Minix780G Series User's Manual
- 1 -
before the operating system is started. Each of POST routines is assigned a POST code, a uniquenumber which is sent to I/O port 080h before the routine is executed.
4.5 BIOS Setup CMOS Setup Utility
4.5.1 CMOS Setup UtilityAfter powering up the system, the BIOS message appears on the screen,when the rst time orwhen CMOS setting wrong, there is following message appears on the screen , but if the rst
rst BIOS be setuped(or loaded default values) and save, the key will be pressed if youwill enter BIOS setup menu.
If this message disappears before you respond, restart the system by pressing + + keys, or by pressing the reset button on computer chassis. Only when these two methodsshould be fail that you restart the system by powering it off and then back on.After pressing or key, the main menu appears.
Press F1 to Run SETUP
In order to increase system stability and performance, our engineering staff is constantly improving the BIOS menu. The BIOS setup screens and descriptions illustrated in this manual are for your reference only, and may not completely match with what you see on your screen.
Do not change the BIOS parameters unless you fully understand its function.
BIOS SETUP UTILITYMain Advanced PCIPnP Boot Security JUSTw00T! Power Exit
System Overview
Select Screen Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit
System Information
System TimeSystem DateLanguage
Floppy A
[22:15:32][Thu 06/19/2008][English]
[1.44 MB 31/ 2
"] Primary IDE Master Primary IDE Slave SATA 1 SATA 2 SATA 3 SATA 4 SATA 5 SATA 6
: [Not Detected]: [Not Detected]: [Hard Disk]: [Not Detected]: [Not Detected]: [Not Detected]: [Not Detected]: [Not Detected]
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
-
8/6/2019 Minix780G Series Ver1.0
19/83
Minix780G Series User's Manual
- 1 -
This is the System Overview, The System Time, System Date, Primary IDE information, SATA port information. System Information
Please Enter this submenu, this will be display BIOS verison, build date, ID number, also willdisplay CPU type, Speed, count, and Memory Size and so on.
Back to Main Setup Menu System timeThis item sets the time you specify(usually the current time)in the format of [Hour],[Minute]and[Second].
System dateThis item sets the date you specify(usually the current date in the format of [Month],[Date],and[Year].
Floppy AAllows you to selects the type of oppy disk drive installed in your system. If you do not
install a oppy disk drive, set this item to None. Language
Allows you to selects the current default language used by the BIOS. Primary IDE Master/Slave
This item sets the status of auto detection of IDE devices while enterting setup, and BIOS willauto detects the presence of IDE devices.
SATA Port 1 /2/3/4/5/6This item sets the status of auto detection of SATA devices while enterting setup, and BIOS willauto detects the presence of SATA devices.
BIOS SETUP UTILITYMain
System Overview
Select Screen Select Item F1 General Help F10 Save and Exit ESC Exit
AMIBIOSVersion :08.00.14Build Date:05/29/08
ID :RS78A210ProcessorAMD Sempron(tm) Processor LE-1100Speed :1912MHzCount :1
System MemorySize :1792MB
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
-
8/6/2019 Minix780G Series Ver1.0
20/83
Minix780G Series User's Manual
- 20 -
Control Key(s) Function Description / Move cursor left or right to select Screens
/ Move cursor up or down to select items +/ -/PU/PD To Change option for the selected items To bring up the selected screen
Main Menu - Quit and not save changes into CMOS Status PageSetup Menu and Option Page Setup Menu - Exit current page andreturn to Main Menu
General help Change Colors
Restore the previous CMOS value from CMOS, only for Option PageSetup Menu
Discard Changes Load Failsafe Defaults Load Optimal Defaults Save con guration changes and exit setup
4.5.2 Control KeysPress F1 to pop up a small help window that describes the appropriate keys to use and thepossible selections for the highlighted item.
Please check the following table for the function description of each control key.
-
8/6/2019 Minix780G Series Ver1.0
21/83
Minix780G Series User's Manual
- 21 -
4.5.3 Advanced Setting
This submenu including these con gurations, such as CPU, Northbridge, Southbridge, OnboardDevice, only CPU Con guration submenu dispay diallog box as follwoing.
BIOS SETUP UTILITYAdvanced
CPU ConfigurationModule Version: 13.29AGESA Version : 3.1.8.0Physical Count: 1Logical Count : 1
This option shouldremain disabled forthe normal operation.The driver developermay enable it fortesting purpose.
Select Screen Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit
AMD Sempron(tm) Processor LE-1100Revision: G1Cache L1: 128KBCache L2: 256KBCache L3: N/ASpeed : 1912MHz, NB Clk: N/ACurrent FSB Multiplier: 9.5xMaximum FSB Multiplier: 9.5xAble to Change Freq. : YesuCode Patch Level : None Required
GART Error ReportingMicrocode UpdateSecure Virtual Machine ModeCool N QuietACPI SRAT Table
[Disabled][Enabled][Enabled][Disabled][Enabled]
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
BIOS SETUP UTILITYMain Advanced PCIPnP Boot Security JUSTw00T! Power Exit
Advanced Settings Configure CPU.
Select Screen Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit
WARNING: Setting wrong values in below sectionsmay cause system to malfunction.
CPU Configuration NorthBridge Configuration SouthBridge Configuration Onboard Device Configuration
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
This is CPU related parameter and CPU setting.
-
8/6/2019 Minix780G Series Ver1.0
22/83
Minix780G Series User's Manual
- 22 -
CPU Con gurationClick key to enter its submenu, it will be display con gureted CPU information, includingModule Version, Manufacturer , CPU type, Frequency, FSB Speed, Cache L1 , Cache L2 and so
on. Cool N QuietEnabled :Lets the AMD Cool N Quiet driver dynamically adjust the CPU clock and VIA to reduce
heat output from your computer and its power consumption.Disabled: Disables this function(Default).
North Bridge Con gurationClick key to enter its submenu, it will be display north bridge chipset con guration, thisitem sets the initate graphic adapter, internal graphics mode select and PEG port selection.
Under this option, there is HDMI function setting for Enabled or Disabled.
NorthBridge Con guration -- >RS780 Con guration -- >Internal Graphics Con guration-->NB Azalia(or HDMI Audio) sets as Enabled or Disabled(Default). South Bridge Con guration
Click key to enter its submenu, it will be dispay south bridge chipset con guration, thisitem sets USB functions, audio controller, PCIE ports selection.
BIOS SETUP UTILITYAdvanced
SB Azalia Audio Configuration USB Configuration
Options for SB HD Azal
Select Screen Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit
OnChip SATA ChannelOnChip SATA TypeSATA IDE Combined ModeCombined Mode Option
[Enabled][Native IDE][Enabled][SATA as primary]
SB CIM Version : 2.5.00
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
SB Azalia Audio Con gurationClick key to enter its submenu. HD Audio Azalia Device
Sets the HD Audio has Enabled or Disabled state. HD Onboard PIN Con g
Enabled : Display the option for Azalia Front Panel in BIOS.Disabled: Disabled the option for Azalia Front Panel in BIOS.
Azalia Front PanelSets the sound function for front panel Enabled or Disabled.
-
8/6/2019 Minix780G Series Ver1.0
23/83
Minix780G Series User's Manual
- 23 -
USB Con gurationClick key to enter its submenu.
BIOS SETUP UTILITY
AdvancedUSB Configuration Enables support for
legacy USB. AUTOoption disableslegacy support ifno USB devices areconnected.
Select Screen Select Item +- Change Option F1 General Help F10 Save and Exit ESC Exit
Module Version -2.24.3-13.4
USB Devices Enabled :None
Legacy USB SupportUSB 2.0 Controller ModeBIOS EHCI Hand-Off
USB1 1.1 ControllerUSB1 2.0 ControllerUSB2 1.1 ControllerUSB2 2.0 Controller
[Enabled][HiSpeed][Enabled]
[Enabled][Enabled][Enabled][Enabled]
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc. Legacy USB Support
Enabled or Disabled Legacy USB option, and Auto option disables legacy support if no USBdevices are connected.
USB 2.0 Controller ModeAllow you to selects the HiSpeed(480Mbps) or FullSpeed(12Mbps).
BIOS EHCI Hand-Off This is a workaround for OSes without EHCI hand-off support. The EHCI ownership changeshould claim by EHCI driver.
USB1 1.1 ControllerAllow you to Enable/Disable USB1 1.1 Controller.
USB1 2.0 ControllerAllow you to Enable/Disable USB1 2.0 Controller.
USB2 1.1 ControllerAllow you to Enable/Disable USB2 1.1 Controller.
USB2 2.0 ControllerAllow you to Enable/Disable USB2 2.0 Controller.
Back to South Bridge Con guration Setup Menu OnChip SATA Channel
This item allows users to enable or disable the SATA controller. OnChip SATA Type
Enables or disables RAID for the SATA controller or con gures the SATA controller to AHCI mode.
-
8/6/2019 Minix780G Series Ver1.0
24/83
Minix780G Series User's Manual
- 2 -
IDE: Disables RAID for the SATA controller and con gures the SATA controller to PATA mode. AHCI: Con gures the SATA controller to AHCI mode. Advanced Host Controller Interface(AHCI)
is an interface speci cation that allows the storage driver to enable advanced Serial ATA
features such as Native Command Queuing and hot plug.RAID/IDE: Enables RAID for the SATA controller. (The IDE controller still operates in PATA mode.) SATA IDE Combined Mode
Available options: Disabled Enabled Combined Mode Option
Available options: SATA as primary SATA as secondary Back to Advanced Setup Menu Onboard Device Con guration
Click key to enter its submenu.
These options allow you to Enabled/Disabled for IDE,Floppy Controller, onboard LAN Control setthe addresses for Serial Port1& Port2. Serial Port 1/2 Address
Enables or disables the rst serial port and speci es its base I/O address and correspondinginterrupt.
Onboard Lan ControlThis option allows you whether enable the onboard LAN.
Onboard Lan Boot RomThese items can change Boot ROM of the LAN chipset.
BIOS SETUP UTILITYAdvanced
Onboard Device Configuration DISABLED: disables theintegrated IDE Controller.PRIMARY: enables only thePrimary IDE Controller.SECONDARY: enables only theSecondary IDE Controller.BOTH: enables both IDE
Controllers. Select Screen Select Item +- Change Option F1 General Help F10 Save and Exit
ESC Exit
Onboard PCI IDE ControllerHard Disk Write ProtectIDE Detect Time Out (Sec)ATA(PI) 80Pin Cable Detection
Onboard Floppy ControllerSerial Port1 AddressSerial Port2 Address
Serial Port2 ModeIR I/O Pin SelectIR Duplex Mode
Onboard Lan ControlOnboard Lan Boot Rom
[Both][Disabled][35][Host & Device]
[Enabled][3F8/IRQ4][2F8/IRQ3][IrDA][SINB/SOUTB][Half Duplex]
[Enabled][Disabled]
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
-
8/6/2019 Minix780G Series Ver1.0
25/83
Minix780G Series User's Manual
- 2 -
4.5.4 PCIPnP SettingBIOS SETUP UTILITY
Main Advanced PCIPnP Boot Security JUSTw00T! Power Exit
Advanced PCI/PnP Settings Clear NVRAM duringSystem Boot.
Select Screen Select Item +- Change Option F1 General Help F10 Save and Exit ESC Exit
WARNING: Setting wrong values in below sectionsmay cause system to malfunction.
Clear NVRAMPlug & Play O/SPCI Latency TimerAllocate IRQ to PCI VGAPalette SnoopingPCI IDE BusMasterOffBoard PCI/ISA IDE Card
[No][No][64][Yes][Disabled][Enabled][Auto]
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc. Clear NVRAM This item for clearing NVRAM during system boot. Plug & Play O/S
This item lets the BIOS con gure all the devices in the system or lets the operating systemcon gure plug and play (PnP) devices not required for boot if your system has a Plug and Playoperating system.
PCI Latency Timer This item sets value in units of PCI clocks for PCI device latency timer register.
Allocate IRQ to PCI VGAThis item assigns IRQ to PCI VGA card if card requests IRQ or doesn't assign IRQ to PCI VGA card even if card requests an IRQ.
Palette Snooping This item informs the PCI devices that an ISA graphics device is installed in the system so the
card will function correctly. PCI IDE BusMaster This item uses PCI busmastering for BIOS reading / writing to IDE derives. OffBoard PCI/ISA IDE Card
This item works for most PCI IDE cards, some PCI IDE cards may require this to be set to thePCI slot number that is holding the card.
-
8/6/2019 Minix780G Series Ver1.0
26/83
Minix780G Series User's Manual
- 2 -
BIOS SETUP UTILITYMain Advanced PCIPnP Boot Security JUSTw00T! Power Exit
Boot Settings Configure Settingsduring System Boot.
Select Screen Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit
Boot Settings Configuration Boot Device Priority Hard Disk Drives Removable Drives CD/DVD Drives
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
BIOS SETUP UTILITYBoot
Boot Settings Configuration Allows BIOS to skipcertain tests whilebooting. This willdecrease the timeneeded to boot thesystem.
Select Screen Select Item +- Change Option F1 General Help F10 Save and Exit
ESC Exit
Quick BootQuiet BootAddOn ROM Display ModeBootup Num-LockWait For 'F1' If ErrorHit 'Del' Message DisplayInterrupt 19 Capture
[Enabled][Disabled][Force BIOS][ON][Enabled][Enabled][Disabled]
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
4.5.5 Boot Setting
Boot Settings Con gurationClick key to enter its submenu.
Quick BootThis item allows you to speed up Power On Self Test (POST) after you power on the computer. If this is set to [Enabled], BIOS will shorten or skip some check items during POST.
Quiet BootIt's for sets post menu and detect device.
AddOn ROM Display ModeSets the display mode for option ROM.
Bootup Num-Lock
Allows you to select the power-on state for the NumLock.
-
8/6/2019 Minix780G Series Ver1.0
27/83
Minix780G Series User's Manual
- 2 -
Wait For 'F1' If ErrorWhen set to Enabled,the system waits for the F1 key t be pressed when error occurs.
Hit 'Del' Message DisplayWhen set to Enabled,the system displays the message "Press DEL to run Setup" durning POST.
Interrupt 19 CaptureWhen set to Enabled, this function allows the option ROMs to trap Interrupt 19.
Back to Boot Setup Menu Boot Device Priority
Click key to enter submenu, it will be display speci es the boot sequence from theavailable devices.
Hard Disk DrivesClick key to enter submenu, it will be display speci es the boot device priority sequence
from available hard disk drives. Removable DrivesClick key to enter submenu, it will be display speci es the boot device priority sequencefrom available removable drives.
CD/DVD DrivesClick key to enter submenu, it will be display speci es the boot device priority sequencefrom available CD/DVD drives.
-
8/6/2019 Minix780G Series Ver1.0
28/83
Minix780G Series User's Manual
- 2 -
This item allows you to Chage Supervisor/User Password, Type the password, up to eightcharacters, and press . The password typed now will clear any previously enteredpassword from CMOS memory. You will be asked tocon rm the password. Type the passwordagain and press .
Note: Dont forget your password. If you forget the password, you will have to open the computer case and clear all information in the CMOS before you can start up the system.But by doing this, you will have to reset all previously set options.
4.5.6 Security SettingBIOS SETUP UTILITY
Main Advanced PCIPnP Boot Security JUSTw00T! Power Exit
Security Settings Install or Change thepassword.
Select Screen Select Item Enter Change F1 General Help F10 Save and Exit ESC Exit
Supervisor Password : Not InstalledUser Password : Not Installed
Change Supervisor PasswordUser Access LevelChange User PasswordClear User Password
Password CheckBoot Sector Virus Protection
[Full Access]
[Setup][Disabled]
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
-
8/6/2019 Minix780G Series Ver1.0
29/83
Minix780G Series User's Manual
- 2 -
BIOS SETUP UTILITYMain Advanced PCIPnP Boot Security JUSTw00T! Power Exit
OverClock Settisng Configure CPUfrequency andvoltage.
Select Screen Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit
AMD Overclocking Configuration DRAM Timing Configuration
Memory CLKCAS Latency (Tcl)RAS/CAS Delay(Trcd)Row Precharge Time(Trp)Min Active RAS(Tras)
RAS/RAS Delay(Trrd)Row Cycle (Trc)
:333MHz:5.0:5 CLK:5 CLK:15 CLK
:3 CLK:21 CLK
Dimm Voltage ControlDram VoltageCPU Voltage ControlVcoreNB Voltage ControlNB VoltageSB Voltage Control
SB VoltageHT Voltage Control
BIOS Write ProtectMemory 2T ModeSideport Memory SelectBIOS Number SelectCPUVID Mode Select
[Auto]:1.856 V
[Auto]:1.296 V
[Auto]:1.176 V
[Auto]
:1.224 V[Auto]
[Enabled][2T Mode][128M][Single BIOS][SVID]
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
4.5.7 JUSTw00T! Setting
AMD Overclocking Con guration This item allows you to set processor frequency, processor voltage, CPU-NB HT link speed, ncHTincoming link width, ncHT outgoing link width, memory con guration and CPU/HT referenceclock.
The option of CPU/HT Reference Clock allows you overclock CPU clock, the Min is 200MHz, theMax is 400, keyin "+"/"-" to select clock.
-
8/6/2019 Minix780G Series Ver1.0
30/83
Minix780G Series User's Manual
- 30 -
BIOS SETUP UTILITYJUSTw00T!
Memory Configuration Enabled Bank MemoryInterleaving
Select Screen Select Item +- Change Option F1 General Help F10 Save and Exit ESC Exit
Bank InterleavingEnable Clock to All DIMMsMemClk Tristate C3/ATLVIDMemory Hole RemappingDCT Unganged Mode
Power Down EnablePower Down Mode
[Auto][Disabled][Disabled][Enabled][Always]
[Enabled][Channel]
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
Memory Con guration Click key to enter its submenu.
Bank Interleaving Sets the bank interleaving feature. Enable Clock to All DIMMs This item is to enable or disable the unused clocks to DIMMs even the memory slots are not
populated.
BIOS SETUP UTILITYJUSTw00T!
AMD Overclocking Configuration
Autox4 800 MHzx4.5 900 MHzx5 1000MHzx5.5 1100 MHzReservedx6.5 1300 MHzReservedx7.5 1500 MHz
Select Screen Select Item +- Change Option F1 General Help F10 Save and Exit ESC Exit
Processor Frequency (FID)Processor Voltage (VID)
CPU-NB HT Link SpeedncHT Incoming Link WidthncHT Outgoing Link Width
Memory ConfigurationCPU/HT Reference Clock (MHz)PCIE Reference Clock (MHz)
A.I. Overclock Function
[Auto][Auto]
[Auto][Auto][Auto]
[200]
A.I. Overclock [Disabled]
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
Options
-
8/6/2019 Minix780G Series Ver1.0
31/83
Minix780G Series User's Manual
- 31 -
BIOS SETUP UTILITYJUSTw00T!
DRAM Timing ConfigurationAutoLimitManual
Select Screen Select Item +- Change Option F1 General Help F10 Save and Exit ESC Exit
Memory Clock ModeDRAM Timing Mode
[Auto][Auto]
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
Options
Bank Interleaving Sets the bank interleaving feature. Enable Clock to All DIMMs This item is to enable or disable the unused clocks to DIMMs even the memory slots are not
populated. MemClk Tristate C3/ATLVID Enables or disables the MemClk Tri-Stating during C3 and Alt VID. Memory Hole Remapping Enables or disables the memory remapping around the memory hole. DCT Unganged Mode This item allows the selection of the unganged DRAM mode (64-bit width). Power Down Enable
This item is to enable or disable the DDR power down mode. Power Down ModeAvailable options: Channel Chip Select
Back to JUSTw00T! Setup Menu PCIE Reference Clock (MHz) It's for adjust PCIE frequency. A.I. Overclock CPU frequency intelligent setting. DRAM Timing Con guration
This submenu allows you to set Memory Clock Mode and DRAM Time Mode.
Memory Clock ModeThis item is to select the memory clock mode.
DRAM Timing Mode This item is to select the DRAM Timing mode.
-
8/6/2019 Minix780G Series Ver1.0
32/83
Minix780G Series User's Manual
- 32 -
Back to JUSTw00T! Setup Menu Dimm Voltage Control
This item allows you to adjust the DRAM Voltage. Dram Voltage
This eld displays the current voltage of DRAM. CPU Voltage Control
This item allows you to adjust the CPU Voltage. Vcore
This eld displays the current voltage of CPU. NB Voltage Control
This item allows you to adjust the NB Voltage. NB Voltage
This eld displays the current voltage of NB. SB Voltage ControlThis item allows you to adjust the SB Voltage.
SB VoltageThis eld displays the current voltage of SB.
HT Voltage ControlThis item allows you to adjust the HT Voltage.
BIOS Write ProtectThis is for BIOS write function, when this option set as Enabled state, then it won't going on ash
bios, or backup BIOS. then it's need to sets disabled(Default).Enable: BIOS ROM Write Protect. Disable: BIOS ROM Not Write Protect.
Memory 2T Mode Available options: Auto 1T Mode 2T Mode Sideport Memory Select
Buide in sideport memory setting . BIOS Number Select
Single BIOS and double BIOS switch . CPUVID Mode Select Available options: SVID PVID
Incorrectly using these features may result in system instability or corruption.Doing a overclock or overvoltage on CPU, chipsets and memory modules mayresult in damages or shortened life expectancy to these components.Please be aware that the menu items are for power users only.
-
8/6/2019 Minix780G Series Ver1.0
33/83
Minix780G Series User's Manual
- 33 -
BIOS SETUP UTILITYMain Advanced PCIPnP Boot Security JUSTw00T! Power Exit
Power Settisng Configure/monitorthe Hardware Health
Select Screen Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit
Hardware Configuration ACPI Configuration APM Configuration
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
BIOS SETUP UTILITYPower
Hardware Health Configuration Fan configurationmode setting
Select Screen Select Item +- Change Option F1 General Help
F10 Save and Exit ESC Exit
System TemperatureCPU TemperatureNB Temperature
CPUFAN Speed
Vcore+3.3VDram VoltageNB VoltageSB Voltage+5VVBATCPUFAN Mode Setting
CPUFAN PWM Control
:45 oC/113 oF:50 oC/122 oF:58 oC/136 oF
:3068 RPM
:1.288 V:3.200 V:1.872 V:1.176 V:1.224 V:4.944 V:3.216 V [Manual Mode ]
[250]
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
4.5.8 Power Setting
Hardware Health Con gure Click key to enter its submenu, it will be display hardware health con guration, including
System temperature, CPU temperature, FAN speed and all kinds of voltages.
CPUFAN Mode Setting Available options: Manual Mode Thermal Cruise Mode Speed Cruise Mode
CPUFAN PWM Control According to PWM out con guration adjustable CPU Fan speed.
-
8/6/2019 Minix780G Series Ver1.0
34/83
Minix780G Series User's Manual
- 3 -
ACPI Con guration These options allow you to manage General/Advanced/Chipset ACPI Con guration, for the
Gerneral ACPI Advanced Con guration, Suspend mode there are three mode for selection,S1(POS), S3(STR),and AUTO, the function explains to following:
S1(POS): Enables the system to enter the ACPI S1(Power on Suspend)sleep state(default),In S1 sleep state, the system appears suspended any stays in a low power modeThe system can be resumed at any time.
S3(STR): Ehables the system to enter the ACPI S3(Suspend to RAM)sleep state. In S3 sleepstate. When signaled by a wake-up device or event, the system resumes to its workingstate exactly where it was left off.
APM Con guration Click key to enter its submenu.
BIOS SETUP UTILITYPower
ACPI Settings Enable/Disable SMIbased power managementand APM support.
Select Screen Select Item +- Change Option F1 General Help F10 Save and Exit ESC Exit
Power Management/APMSuspend Time OutPower Button ModeVideo Power Down ModeHard Disk Power Down ModeHard Disk Time Out (Minute)PWRON After PWR-FailResume By RTC AlarmKeyboard WakeUpSpecific Key for PowerOn
[Enabled][Disabled][On/Off][Suspend][Suspend][Disabled][OFF][Disabled][Disabled]
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
Power Management/APMEnable or disable APM.
Suspend Time Out
All device will be turn off include CPU if system has not to activated in setting time . Power Button ModeAllows the system to go into On/Off mode or suspend mode when the power button is pressed.
Video Power Down Mode Available options: Disabled Standby Suspend Hard Disk Power Down Mode Available options: Disabled Standby Suspend Hard Disk Time Out (Minute) Available options: Disabled 1~15
-
8/6/2019 Minix780G Series Ver1.0
35/83
Minix780G Series User's Manual
- 3 -
4.5.9 Exit SettingBIOS SETUP UTILITY
Main Advanced PCIPnP Boot Security JUSTw00T! Power Exit
Exit Options Exit system setupafter saving thechanges.
F10 key can be usedfor this operation.
Select Screen Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit
Save Changes and ExitDiscard Changes and ExitDiscard Changes
Load Optimal DefaultsLoad Failsafe Defaults
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
PWRON After PWR-FailThis item selects the system action after an AC power failure.
[Off]: When power returns after an AC power failure, the systems power remains off.You must press the Power button to power-on the system.
[On]: When power returns after an AC power failure, the systems power will be powered onautomatically.
[Former-Sts]: When power returns after an AC power failure, the system will return to thestate where you left off before power failure occurred. If the systems poweris off when AC power failure occurs, it will remain off when power returns. If the systems power is on when AC power failure occurs, the system willpower-on when power returns.
Resume By RTC Alarm
Allows you to enable or disable RTC to generate a wake event. When this item is set toEnabled,the items RTC Alarm Date,RTC Alarm Hour,RTC Alarm Minute,and RTC Alarm Secondappear with set values.
Keyboard WakeUpPS/2 keyboard activity wakes the computer from an ACPI S1 or S3 state.
Speci c Key for PowerOnWhen the Power On function is set to Password, use this item to set the password.
Mi i 780G S i U ' M l
-
8/6/2019 Minix780G Series Ver1.0
36/83
Minix780G Series User's Manual
- 3 -
Highlight this item and select ,then press to save the changes that you havemade in the Setup Utility and exit the Setup Utility. Or press to return to the mainmenu.
BIOS SETUP UTILITYMain Advanced PCIPnP Boot Security JUSTw00T! Power Exit
Exit Options Exit system setupafter saving thechanges.
F10 key can be usedfor this operation.
Select Screen Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit
Save Changes and ExitDiscard Changes and ExitDiscard Changes
Load Optimal DefaultsLoad Failsafe Defaults
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
for this
Se SeEnter GoF1 Ge
efaultsDefaults
Save configuration changes and exit setup?
[Ok] [Cancel][Ok]
BIOS SETUP UTILITYMain Advanced PCIPnP Boot Security JUSTw00T! Power Exit
Exit Options Exit system setupwithout saving anychanges.
ESC key can be usedfor this operation.
Select Screen Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit
Save Changes and ExitDiscard Changes and ExitDiscard Changes
Load Optimal DefaultsLoad Failsafe Defaults
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
for this
Se SeEnter GoF1 Ge
ltsults Discard changes and exit setup?
[Ok] [Cancel][Ok]
Highlight this item and select ,then press to discard any changes that you have
made in the Setup Utility and exit the Setup Utility. Or press to return to the mainmenu.
Minix780G Series User's Manual
-
8/6/2019 Minix780G Series Ver1.0
37/83
Minix780G Series User's Manual
- 3 -
BIOS SETUP UTILITYMain Advanced PCIPnP Boot Security JUSTw00T! Power Exit
Exit Options Discards changesdone so far to any ofthe setup questions.F7 key can be usedfor this operation.
Select Screen Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit
Save Changes and ExitDiscard Changes and ExitDiscard Changes
Load Optimal DefaultsLoad Failsafe Defaults
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
Discard changes?
[Ok] [Cancel][Ok]
BIOS SETUP UTILITYMain Advanced PCIPnP Boot Security JUSTw00T! Power Exit
Exit Options Load Optimal Defaultvalues for all thesetup questions.
F9 key can be usedfor this operation.
Select Screen Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit
Save Changes and ExitDiscard Changes and ExitDiscard Changes
Load Optimal DefaultsLoad Failsafe Defaults
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
Load Optimal Defaults?
[Ok] [Cancel][Ok]
Sleect and press to discard changes and exit, or press to return to themain menu.
This option opens a dialog box that let you install optimized defaults for all appropriate items inthe Setup Utility. Select and then to install the defaults. select andthen to not install the defaults. The optimized defaults place demand on the systemthat may be greater than the performance level of the components, such as the CPU and the
memory. You can cause fatal errors or instability if you install the optimized defaults when yourhardware does not support them. If you only want to install setup defaults for a speci c option,select and display that option, and then press .
Minix780G Series User's Manual
-
8/6/2019 Minix780G Series Ver1.0
38/83
Minix780G Series User s Manual
- 3 -
BIOS SETUP UTILITYMain Advanced PCIPnP Boot Security JUSTw00T! Power Exit
Exit Options Load Failsafe Defaultvalues for all thesetup questions.
F8 key can be usedfor this operation.
Select Screen Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit
Save Changes and ExitDiscard Changes and Exit
Discard ChangesLoad Optimal DefaultsLoad Failsafe Defaults
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
Load Failsafe Defaults?
[Ok] [Cancel][Ok]
This option opens a dialog box that lets you install fail-safe defaults for all appropriate items inthe Setup Utility: Select and the to install the defaults. Select and then to not install the defaults. The fail-safe defaults place no great demand on the systemand are generally stable. If your system is not functioning correctly, try installing the fail-safedefaults as a rst step in getting your system working properly again.If you only want to installfail-safe defaults for a speci c option, select and display that option, and then press .
Minix780G Series User's Manual
-
8/6/2019 Minix780G Series Ver1.0
39/83
Minix780G Series User s Manual
- 3 -
+ Mainboard Driver Installation Utility+ Userful Software Utility> Browse CD
Exit
Chapter 5 Driver Installation
Check your package and there is Driver CD included. This CD consists of all drivers you need. Inaddition, this CD also include an auto detect software which can tell you which hardware is installed,and which drivers needed so that your system can function properly.Insert CD into your CD-ROM drive and the menu should appear as below. If the menu does notappear, double-click My Computer / double-click CD-ROM drive or click Start / click Run / type X:\
AUTORUN.EXE (assuming X is your CD-ROM drive).
(This picture is only for reference)
From the Main MENU you may make 4 selections:1. +Mainboard Driver Installation Utility: Click to enter the driver installation menu.2. +Useful Software Utility: Click to enter the utilities installation menu.3. >Browse CD: Click to browse the contents of this Driver & Utility CD.4. Exit: Click to exit this installation menu.
-
8/6/2019 Minix780G Series Ver1.0
40/83
-
8/6/2019 Minix780G Series Ver1.0
41/83
: 1.00, 2008 7P/N: 80ECN78010
Minix780GSocket AM2/AM2+
Website: http://www.jwele.com.cn
-
8/6/2019 Minix780G Series Ver1.0
42/83
-
8/6/2019 Minix780G Series Ver1.0
43/83
1 ............................................................................................................44 1.1 ...........................................................................................................................44 1.2 ...........................................................................................................................45 1.3 .......................................................................................................................461.4 ....................................................................................................................47
2 ......................................................................................................482.1 I/O ...............................................................................................................482.2 .................................................................................................................482.3 CPU ...........................................................................................................48
2.3.1 CPU .....................................................................................................................49 2.3.2 CPU ...............................................................................................................49 2.4 ...........................................................................................................................50 2.5 ....................................................................................................................51 2.5.1 IDE ............................................................................................................51 2.5.2 Serial ATA .........................................................................................................51 2.5.3PCI Express ...........................................................................................................51
3 ............................................................................................524 BIOS .....................................................................................................57
4.1 BIOS ...................................................................................................................574.2 BIOS ..........................................................................................................................57
4.2.1 BIOS ......................................................................................................574.2.2 .....................................................................................................................57
4.2.3 Main (BIOS ) ......................................................................................................58 4.2.4 Advanced ( BIOS ) .......................................................... ........................... 61 4.2.5 PCIPnP (PCIPnP ) ...................................................................................................67 4.2.6 Boot ( )...........................................................................................................68
4.2.7 Security ( )
......................................................................................................70 4.2.8 JUSTw00T! ( ) .................................................................................................724.2.9 Power ( ) ..................................................................................................764.2.10 Exit ( BIOS ) ...................................................... ...................................... 795 ......................................................................................................82
Minix 0G
-
8/6/2019 Minix780G Series Ver1.0
44/83
- -
1
1.1
X 1 0-Pin IDE X 1 SATA X 1
I/O X 1 X 1 X 1 SATA X 1 ( )
Minix 0G
-
8/6/2019 Minix780G Series Ver1.0
45/83
- -
1.2
CPU
- Socket AM2 AMD Athlon TM /Ahtlon TM FX/Athlon TM X2/
SempronTM
, AM2+- H.T 3.0- AMD CPU Cool 'n' Quiet
: 125W CPU, CPU
- AMD RS 0G+SB 00- ATI Radeon HD 3200 DirectX 10- 2 200-pin DDRII SODIMM- .0 GB- DDRII 10 MHz/ 00MHz/ MHz/ 33MHz
BIOS
- AMI BIOS- BIOS- ACPI- STR - CPU , ,- 1 x PS/2- 1 x VGA- 1 x DVI
- 1 x HDMI- 1 x eSATA- 1 x COM ( )- 1 x RJ- 10 x USB 2.0 , USB 1.1- 1 x IR ( )- x SATAII 3Gb/s RAID 0 RAID 1 RAID 10- 1 x IDE , IDE ATA /100/133
- / HD Audio Codec ( )-- 10/100/1000Mbps ( )- 1 x PCI Express x (PCI Express 2.0)Mini ITX (170mm*170mm)
Minix 0G
-
8/6/2019 Minix780G Series Ver1.0
46/83
- -
1.3
( )
Minix 0G
-
8/6/2019 Minix780G Series Ver1.0
47/83
- -
1.4
( )
PS/2 Keyboard: PS/2 HDMI: (HDMI) / AV SPDIF IN: S/PDIF SPDIF OUT: S/PDIF DVI: (DVI)
VGA: D-Sub VGA eSATA: SATA USB: USB LAN: RJ- AUDIO1:
Cen./Sub. ( / ): .1 R.L./R.R. ( / ): .1S.L./S.R. ( / ): .1Line-In ( ):Line-Out ( ): .1
Mic-In ( ):
-
8/6/2019 Minix780G Series Ver1.0
48/83
Minix 0G 3 CPU
-
8/6/2019 Minix780G Series Ver1.0
49/83
- -
3. CPU. CPU CPU. CPU
CPU
2.3.1 CPU1. CPU ZIF 0 2. CPU CPU
3. CPU CPUCPU
. CPU CPU
CPU
1
3
2.3.2 CPUCPU
2
Minix 0G
-
8/6/2019 Minix780G Series Ver1.0
50/83
- 0 -
2.4Minix 0G 2 200Pin DDRII SODIMM
( )
1.
2.3.
:1. AC
2.3.
()
. DIMM
1
2
3
Minix 0G
2.5
-
8/6/2019 Minix780G Series Ver1.0
51/83
- 1 -
2.52.5.1 IDE
32 PCI IDEPIO 0 Ultra DMA
33/ /100/133 IDEIDE IDE
IDE
2.5.2 Serial ATA Serial ATA Serial ATA Serial ATA
2.5.3 PCI Express PCIE1 PCI Express X
Minix 0G
-
8/6/2019 Minix780G Series Ver1.0
52/83
- 2 -
3
1 JBAT 3 9 FUSB1/FUSB2
2 JDVI_HDMI 3 10 SPEAKER13 J5VDUAL 11 FPANEL4 CFAN 12 IR15 SFAN1 13 JCOM16 SFAN2 14 J17 CD_IN 15 PWR12V8 F_AUDIO 16 ATXPWR
1
2
3
4
5
67
8
9 10
11
12
13 14
15
16
Minix 0G
-
8/6/2019 Minix780G Series Ver1.0
53/83
- 3 -
Normal(Default )
Clear CMOS
J BAT o r C LR C MO S1_
1 2 3
1 2 3
2
3 1 2 2 3
1
"1" 1
1-JBAT( CMOS ) (a) CMOS (b) BIOS (c) BIOSCPU (d) CPU CMOS
CMOS BIOS 1 2 ( ) 2 3 CMOS
CMOS 1. 2. 2 3
--- 1 2
3. . BIOS CPU BIOS . CPU . BIOS
2-JDVI_HDMI(DVI/HDMI )
1-2 Auto 1-2,DVIHDMI
2-32-3 DVI/HDMI EN
Minix 0G
3-J5VDUAL( )
-
8/6/2019 Minix780G Series Ver1.0
54/83
- -
3 J5VDUAL( )1-2 Enable 1-2,
2-32-3 Disable
4/5/6-CFAN/SFAN1/SFAN2( )CFAN
12 +12V3
SFAN1/SFAN2
12 +12V3
7-CD_IN(CD )
123
8-F_AUDIO( )
1 PROT1L 6 SENSE1_RETURN2 AGND 7 SENSE_SEND3 PROT1R 8 NC4 PRESENCE# 9 PORT2L5 PORT2R 10 SENSE2_RETURN
Minix 0G
9-FUSB1/FUSB2(USB )
-
8/6/2019 Minix780G Series Ver1.0
55/83
- -
( )
1 VCC 2 VCC
3 Data 0- 4 Data 1-5 Data 0+ 6 Data 1+7 Ground 8 Ground
10 NC
1
2
9
10
USB 2.0/1.1 USBUSB
USB
10/11-SPEAKER1/FPANEL(PC / )
+/-SPEAKER1:
1 SPK +2 NC3 NC4 SPK -
PWR-LED ( )
PWR-ON ( )
HDD_LED ( )
RESET ( )
SPEAKER (PC )
12-IR1( )BIOS IR
1 VCC2 NC3 IRRX4 GND5 IRTX
Minix 0G
13-JCOM1( COM )
-
8/6/2019 Minix780G Series Ver1.0
56/83
- -
( )JCOM1
1 DCD 2 RXD3 TXD 4 DTR 5 GND 6 DSR 7 CTS 8 RTS9 RI
14-J1( ) ( )
15/16-PWR12V/ATXPWR(4-pin 12V /24-pin ATX )
PWR12V CPU
20-pin ATX pin 1 & pin 13
+ .++
+
+
+ ..
3 3V12V12V
5VSBPW R OK
COM5V
COM
5VCOM3 3V
+3 3V
COM5V5V5V5V
COMCOMCOM
PS ONCOM12V3 3V
+++-
_
-+ .
1
12
13
24
Minix 0G
4 BIOS
-
8/6/2019 Minix780G Series Ver1.0
57/83
- -
4 BIOS
4.1 BIOS AMI BIOS BIOS Basic Input Output System(ROM Read-Only Memory) BIOS
a. POST(Power On Self Test) b.c.d.
BIOS CMOS RAMBIOS CMOS
BIOS
4.2 BIOS BIOS Setup BIOS
SETUPa . SETUPb.
BIOS BIOS
4.2.1 BIOS
BIOS
CMOS CMOS Settings Wrong Press F1 to Run SETUP F1 BIOS
4.2.2 Page Up Page Down
Press DEL to enter SETUP
Minix 0G
-
8/6/2019 Minix780G Series Ver1.0
58/83
- -
/
/
+/ - / CMOS SETUP/
CMOS
4.2.3 Main (BIOS )BIOS SETUP UTILITY
Main Advanced PCIPnP Boot Security JUSTw00T! Power Exit
System Overview
Select Screen Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit
System Information
System TimeSystem DateLanguageFloppy A
[22:15:32][Thu 06/19/2008][English][1.44 MB 3 1/ 2"]
Primary IDE Master Primary IDE Slave
SATA 1 SATA 2 SATA 3 SATA 4 SATA 5 SATA 6
: [Not Detected]: [Not Detected]
: [Hard Disk]: [Not Detected]: [Not Detected]: [Not Detected]: [Not Detected]: [Not Detected]
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
System InformationAMIBIOS/ /
Minix 0G
BIOS SETUP UTILITYMain
-
8/6/2019 Minix780G Series Ver1.0
59/83
- -
Main
System Overview
Select Screen Select Item F1 General Help F10 Save and Exit ESC Exit
AMIBIOSVersion :08.00.14Build Date:05/29/08ID :RS78A210
ProcessorAMD Sempron(tm) Processor LE-1100Speed :1912MHzCount :1
System MemorySize :1792MB
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
Main System Time
< >< >< >System Date ( )
, / /
Floppy A 3 0K, .2 in/1.2M, .2 in/ 20K,3. in/1. M,3. in/2. M,3. in/DisabledLanguage
BIOS English Chinese(GB)( ) Primary IDE Master/Slave, SATA 1/2/3/ / / (IDE/SATA )
IDE/SATA
Minix 0G
BIOS SETUP UTILITYMain
-
8/6/2019 Minix780G Series Ver1.0
60/83
- 0 -
Main
SATA 1 Disabled: Disables LBAMode.Auto: Enables LBA Modeif the device supportsit and the device isnot already formattedwith LBA Modedisabled.
Select Screen Select Item +- Change Option F1 General Help F10 Save and Exit ESC Exit
Device :Hard DiskVendor :ST380215ASSize :80.0GBLBA Mode :SupportedBlock Mode:16SectorsPIO Mode :4Async DMA :MultiWord DMA-2Ultra DMA :Ultra DMA-6S.M.A.R.T.:Supported
LBA/Large ModeBlock (Multi-Sector Transfer)PIO ModeDMA ModeS.M.A.R.T32Bit Data Transfer
[Auto][Auto][Auto][Auto][Auto][Enabled]
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
LBA/Large ModeLBA
Block (Multi-Sector Transfer)
PIO ModePIO
DMA ModeDMA
S.M.A.R.T(Smart Monitoring,Analysis,and Reporting Technology)
32Bit Data Transfer
32
Minix 0G
BIOS SETUP UTILITY
4.2.4 Advanced ( BIOS )
-
8/6/2019 Minix780G Series Ver1.0
61/83
- 1 -
BIOS SETUP UTILITYAdvanced
CPU ConfigurationModule Version: 13.29AGESA Version : 3.1.8.0Physical Count: 1Logical Count : 1
This option shouldremain disabled forthe normal operation.The driver developermay enable it fortesting purpose.
Select Screen Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit
AMD Sempron(tm) Processor LE-1100Revision: G1Cache L1: 128KBCache L2: 256KBCache L3: N/ASpeed : 1912MHz, NB Clk: N/ACurrent FSB Multiplier: 9.5xMaximum FSB Multiplier: 9.5xAble to Change Freq. : YesuCode Patch Level : None Required
GART Error ReportingMicrocode UpdateSecure Virtual Machine ModeCool N QuietACPI SRAT Table
[Disabled][Enabled][Enabled][Disabled][Enabled]
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
BIOS SETUP UTILITYMain Advanced PCIPnP Boot Security JUSTw00T! Power Exit
Advanced Settings Configure CPU. Select Screen Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit
WARNING: Setting wrong values in below sectionsmay cause system to malfunction.
CPU Configuration NorthBridge Configuration SouthBridge Configuration Onboard Device Configuration
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
CPU Con guration (CPU )
CPU CPU Advanced
Minix 0G NorthBridge Chipset Con guration ( )
-
8/6/2019 Minix780G Series Ver1.0
62/83
- 2 -
BIOS SETUP UTILITYAdvanced
NorthBridge Chipset Configuration
Select Screen Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit
RS780 Configuration
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
Internal Graphics Con guration ( )
RS 0 Con guration (RS 0 )
BIOS SETUP UTILITYAdvanced
RS780 Configuration
RS780 CIMx Version : 4.0.2
Internal GraphicsConfiguration
Select Screen Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit
Internal Graphics Configuration
Primary Video Controller [PCI-GFX0-GPP-IGFX]
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
Minix 0G
BIOS SETUP UTILITYAdvanced
-
8/6/2019 Minix780G Series Ver1.0
63/83
- 3 -
Internal Graphics Configuration
DisableUMASIDEPORTUMA+SIDEPORTR
Select Screen Select Item +- Change Option F1 General Help F10 Save and Exit ESC Exit
Internal Graphics ModeUMA Frame Buffer Size
GFX Engine Clock Override
Surround ViewFB Location
HDMI AudioGPPSB Core Configuration
[UMA][Auto][Disable]
[Disabled][Above 4G]
[Enable][Auto]
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
Options
Internal Graphics Mode
UMA Frame Buffer Size
GFX Engine Clock Override
Surround ViewFB Location
G ABOVE GHDMI Audio
, HDMIGPPSB Core Con guration
Auto RS 0 Con guration
Primary Video Controller ( )
Advanced
-
8/6/2019 Minix780G Series Ver1.0
64/83
Minix 0G
BIOS SETUP UTILITY
USB Con guration (USB )
-
8/6/2019 Minix780G Series Ver1.0
65/83
- -
BIOS SETUP UTILITYAdvanced
USB Configuration Enables support forlegacy USB. AUTOoption disableslegacy support ifno USB devices areconnected.
Select Screen Select Item +- Change Option F1 General Help F10 Save and Exit ESC Exit
Module Version -2.24.3-13.4
USB Devices Enabled :None
Legacy USB SupportUSB 2.0 Controller ModeBIOS EHCI Hand-Off
USB1 1.1 ControllerUSB1 2.0 ControllerUSB2 1.1 ControllerUSB2 2.0 Controller
[Enabled][HiSpeed][Enabled]
[Enabled][Enabled][Enabled][Enabled]
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.Legacy USB Support ( USB )
/ USB 2.0 Controller Mode (USB 2.0 )
USB 2.0BIOS EHCI Hand-Off
BIOS EHCI Hand-Off USB1 1.1 Controller (USB1 1.1 )
: Enabled DisabledUSB1 2.0 Controller (USB1 2.0 )
: Enabled DisabledUSB2 1.1 Controller (USB2 1.1 )
: Enabled Disabled
USB2 2.0 Controller (USB2 2.0 ): Enabled Disabled SouthBridge Chipset Con guration
OnChip SATA Channel ( SATA )SATA
OnChip SATA Type ( SATA )SATA
SATA IDE Combined Mode (SATA/IDE )Enabled Disabled
Minix 0G Combined Mode Option ( )
SATA as primary SATA as secondary Advanced
-
8/6/2019 Minix780G Series Ver1.0
66/83
- -
BIOS SETUP UTILITYAdvanced
Onboard Device Configuration DISABLED: disables theintegrated IDE Controller.PRIMARY: enables only thePrimary IDE Controller.SECONDARY: enables only theSecondary IDE Controller.BOTH: enables both IDEControllers.
Select Screen Select Item +- Change Option F1 General Help F10 Save and Exit
ESC Exit
Onboard PCI IDE ControllerHard Disk Write ProtectIDE Detect Time Out (Sec)ATA(PI) 80Pin Cable Detection
Onboard Floppy ControllerSerial Port1 AddressSerial Port2 Address
Serial Port2 ModeIR I/O Pin SelectIR Duplex Mode
Onboard Lan ControlOnboard Lan Boot Rom
[Both][Disabled][35][Host & Device]
[Enabled][3F8/IRQ4][2F8/IRQ3][IrDA][SINB/SOUTB][Half Duplex]
[Enabled][Disabled]
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
OnBoard PCI IDE Controller ( PCI IDE )IDE
Hard Disk Write Protect ( )
IDE Detect Time Out (Sec)BIOS IDE
ATA(PI) 0Pin Cable DetectATA PI 0pin
Onboard Floppy Controller ( )Disabled EnabledSerial Port1 Address ( IO )
Disabled 3F /IRQ 3E /IRQ 2E /IRQ3Onboard Lan Control ( )
Onboard Lan Boot Rom ( ROM)ROM
Advanced Onboard Device Con guration ( )
Minix 0G
BIOS SETUP UTILITYMain Advanced PCIPnP Boot Security JUSTw00T! Power Exit
4.2.5 PCIPnP (PCIPnP )
-
8/6/2019 Minix780G Series Ver1.0
67/83
- -
Main Advanced PCIPnP Boot Security JUSTw00T! Power Exit
Advanced PCI/PnP Settings Clear NVRAM duringSystem Boot.
Select Screen Select Item +- Change Option F1 General Help
F10 Save and Exit ESC Exit
WARNING: Setting wrong values in below sectionsmay cause system to malfunction.
Clear NVRAMPlug & Play O/SPCI Latency TimerAllocate IRQ to PCI VGAPalette SnoopingPCI IDE BusMaster
OffBoard PCI/ISA IDE Card
[No][No][64][Yes][Disabled][Enabled]
[Auto]
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
Clear NVRAM ( NVRAM )Yes No
Plug & Play O/S ( )IRQ BIOS
Yes No
PCI Latency Timer (PCI ) PCI PCI32 12 1 0 1 2 22 2
Allocate IRQ to PCI VGA ( IRQ PCI VGA)IRQ PCI
Yes NoPalette Snooping
PCI VGADisabled Enabled
PCI IDE BusMaster (PCI IDE )BIOS PCI IDE /
Disabled EnabledOffBoard PCI/ISA IDE Card ( PCI/ISA IDE
IDEAuto PCI Slot1
Minix 0G
BIOS SETUP UTILITYM i Ad d PCIP P B t S it JUST 00T! P E it
4.2.6 Boot ( )
-
8/6/2019 Minix780G Series Ver1.0
68/83
- -
Main Advanced PCIPnP Boot Security JUSTw00T! Power Exit
Boot Settings Configure Settingsduring System Boot.
Select Screen Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit
Boot Settings Configuration Boot Device Priority Hard Disk Drives Removable Drives CD/DVD Drives
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
BIOS SETUP UTILITYBoot
Boot Settings Configuration Allows BIOS to skipcertain tests whilebooting. This willdecrease the timeneeded to boot thesystem.
Select Screen Select Item +- Change Option F1 General Help F10 Save and Exit
ESC Exit
Quick BootQuiet BootAddOn ROM Display ModeBootup Num-LockWait For 'F1' If ErrorHit 'Del' Message DisplayInterrupt 19 Capture
[Enabled][Disabled][Force BIOS][ON][Enabled][Enabled][Disabled]
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
Boot Settings Con guration ( )
Quick Boot ( )
Disable Enabled Disabled EnabledQuiet Boot ( )
Disabled EnabledAddOn ROM Display Mode ( )
Force BIOS
Minix 0G Bootup Num-Lock ( )
Numlock On NumLock Off Numlock
-
8/6/2019 Minix780G Series Ver1.0
69/83
- -
Wait For F1 If Error ( )
F1
Hit Del Message Display ( DEL )Enabled] (Press DEL to run Setup)
Disabled EnabledInterrupt 1 Capture (PCI )
PCI Enabled Disabled Enabled
Boot Boot Device Priority ( )
BIOS SETUP UTILITYBoot
Boot Device Priorty Specifies the bootsequence from theavailable devices.
A device enclosed inparenthesis has been
disabled in thecorresponding typemenu.
Select Screen Select Item +- Change Option F1 General Help F10 Save and Exit ESC Exit
1st Boot Device2nd Boot Device3rd Boot Device
[1st FLOPPY DRIVE][CD/DVD:3S-TSSTcorp][SATA:3M-ST380215AS]
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc. Boot
Removable Drives ( )
Hard Disk Drives ( )
CD/DVD Drives (CD/DVD ) CD/DVD
Minix 0G
BIOS SETUP UTILITYMain Advanced PCIPnP Boot Security JUSTw00T! Power Exit
4.2.7 Security ( )
-
8/6/2019 Minix780G Series Ver1.0
70/83
- 0 -
Main Advanced PCIPnP Boot Security JUSTw00T! Power Exit
Security Settings Install or Change thepassword.
Select Screen Select Item Enter Change F1 General Help F10 Save and Exit
ESC Exit
Supervisor Password : Not InstalledUser Password : Not Installed
Change Supervisor PasswordUser Access LevelChange User PasswordClear User PasswordPassword Check
Boot Sector Virus Protection
[Full Access]
[Setup]
[Disabled]
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
Change Supervisor Password ( )
1. Change Supervisor Password 2. Enter New Password
Con rm Password
Password installed Supervisor Password Installed Password do not match! Change Supervisor Password Enter Password
Password uninstalled User Access Level ( )
BIOS Full Access No Access View Only Limited No Access BIOSView Only BIOS Limited
Full Access BIOS Change User Password ( )
1. Change User Password 2. Enter New Password
3. Con rm Password Password installed User Password
-
8/6/2019 Minix780G Series Ver1.0
71/83
Minix 0G
BIOS SETUP UTILITYMain Advanced PCIPnP Boot Security JUSTw00T! Power Exit
4.2.8 JUSTw00T! ( )
-
8/6/2019 Minix780G Series Ver1.0
72/83
- 2 -
OverClock Settisng Configure CPUfrequency andvoltage.
Select Screen Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit
AMD Overclocking Configuration DRAM Timing Configuration
Memory CLKCAS Latency (Tcl)RAS/CAS Delay(Trcd)Row Precharge Time(Trp)Min Active RAS(Tras)RAS/RAS Delay(Trrd)
Row Cycle (Trc)
:333MHz:5.0:5 CLK:5 CLK:15 CLK:3 CLK
:21 CLK
Dimm Voltage ControlDram VoltageCPU Voltage ControlVcoreNB Voltage ControlNB VoltageSB Voltage ControlSB Voltage
HT Voltage ControlBIOS Write ProtectMemory 2T ModeSideport Memory SelectBIOS Number SelectCPUVID Mode Select
[Auto]:1.856 V
[Auto]:1.296 V
[Auto]:1.176 V
[Auto]:1.224 V
[Auto][Enabled][2T Mode][128M][Single BIOS][SVID]
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc. AMD Overclocking Con guration (AMD )
AMD CPU
Minix 0G
BIOS SETUP UTILITYJUSTw00T!
AMD Overclocking Configuration Options
-
8/6/2019 Minix780G Series Ver1.0
73/83
- 3 -
BIOS SETUP UTILITYJUSTw00T!
Memory Configuration Enabled Bank Memory
Interleaving Select Screen Select Item +- Change Option F1 General Help F10 Save and Exit ESC Exit
Bank InterleavingEnable Clock to All DIMMsMemClk Tristate C3/ATLVIDMemory Hole RemappingDCT Unganged ModePower Down Enable
Power Down Mode
[Auto][Disabled][Disabled][Enabled][Always][Enabled][Channel]
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
g g
Autox4 800 MHzx4.5 900 MHzx5 1000MHzx5.5 1100 MHzReservedx6.5 1300 MHzReservedx7.5 1500 MHz
Select Screen
Select Item +- Change Option F1 General Help F10 Save and Exit ESC Exit
Processor Frequency (FID)Processor Voltage (VID)
CPU-NB HT Link SpeedncHT Incoming Link WidthncHT Outgoing Link Width
Memory ConfigurationCPU/HT Reference Clock (MHz)PCIE Reference Clock (MHz)
A.I. Overclock Function
[Auto][Auto]
[Auto][Auto][Auto]
[200]
A.I. Overclock [Disabled]
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
p
Processor Frequency (FID) CPUCPU CPU
Processor Voltage (VID) CPUCPU CPU
CPU-NB HT Link Speed CPU-NBCPU-NB
Memory Con guration ( )
Minix 0G Bank Interleaving
Bank L-Bank DDR RAM L-Bank Auto SPD L-Bank
-
8/6/2019 Minix780G Series Ver1.0
74/83
- -
BIOS SETUP UTILITYJUSTw00T!
DRAM Timing Configuration
Auto
LimitManual Select Screen Select Item +- Change Option F1 General Help F10 Save and Exit ESC Exit
Memory Clock ModeDRAM Timing Mode
[Auto][Auto]
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
Options
Enable Clock to All DIMMs
MemClk Tristate C3/ATLVIDMemCLK Tri-Stating During C3 and Alt VID
Memory Hole Remapping00E0
DCT Unganged ModeDCT UngangedPower Down Enable
Power Down ModeChannel Chip Select
AMD Overclocking Con guration CPU/HT Reference Clock (MHz)
CPU , CPU ,PCIE Reference Clock (MHz)
PCIE PCIE Clock PCI-EA.I. Overclock
CPU Disabled 210MHz 220MHz 230MHz 2 0MHz 2 0MHz JUSTw00T! DRAM Timing Con guration
-
8/6/2019 Minix780G Series Ver1.0
75/83
Minix 0G
BIOS SETUP UTILITYMain Advanced PCIPnP Boot Security JUSTw00T! Power Exit
4.2.9 Power ( )
-
8/6/2019 Minix780G Series Ver1.0
76/83
- -
Power Settisng Configure/monitorthe Hardware Health
Select Screen Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit
Hardware Configuration ACPI Configuration APM Configuration
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
BIOS SETUP UTILITYPower
Hardware Health Configuration Fan configurationmode setting
Select Screen Select Item +- Change Option F1 General Help F10 Save and Exit ESC Exit
System TemperatureCPU TemperatureNB TemperatureCPUFAN Speed
Vcore+3.3VDram VoltageNB VoltageSB Voltage+5VVBATCPUFAN Mode Setting
CPUFAN PWM Control
:45 oC/113 oF:50 oC/122 oF:58 oC/136 oF:3068 RPM
:1.288 V:3.200 V:1.872 V:1.176 V:1.224 V:4.944 V:3.216 V [Manual Mode ]
[250]
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
Hardware Health Con guration ( )CPU
CPUFAN Mode Settings (CPU )Manual Mode Thermal Cruise Mode Speed Cruise Mode
CPUFAN PWM Control (CPU PWM( pin) )0~2 0
Minix 0G
BIOS SETUP UTILITY
Power ACPI Con guration (ACPI )
-
8/6/2019 Minix780G Series Ver1.0
77/83
- -
PowerACPI Settings General ACPI
Configuration settings
Select Screen Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit
General ACPI Configuration
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
BIOS SETUP UTILITYPower
General ACPI Configuration Select the ACPIstate used forSystem Suspend.
Select Screen Select Item +- Change Option F1 General Help F10 Save and Exit ESC Exit
Suspend modeRepost Video on S3 ResumeC States Support
[Auto][No][Disabled]
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.Suspend mode
Repost Video on S3 ResumeS3/STR VGA BIOS
C States SupportDisabled Enabled
Power APM Con guration (APM )
General ACPI Con guration
Minix 0G
BIOS SETUP UTILITYPower
ACPI Settings Enable/Disable SMIbased power management
-
8/6/2019 Minix780G Series Ver1.0
78/83
- -
based power management
and APM support.
Select Screen Select Item +- Change Option F1 General Help F10 Save and Exit ESC Exit
Power Management/APMSuspend Time OutPower Button ModeVideo Power Down ModeHard Disk Power Down ModeHard Disk Time Out (Minute)PWRON After PWR-FailResume By RTC AlarmKeyboard WakeUpSpecific Key for PowerOn
[Enabled][Disabled][On/Off][Suspend][Suspend][Disabled][OFF][Disabled][Disabled]
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.Power Management/APM
APM (Enabled)Suspend Time Out ( )
CPUPower Button Mode
On/Off ATX ATXSuspend ATX ATX
Video Power Down Mode
Hard Disk Power Down Mode
Hard Disk Time Out (Minute)
PWRON After PWR-Fail ( ) OFF
ON Former-Sts
OFF
Resume By RTC Alarm/ Enabled BIOS
RTC Alarm Date (Days) RTC Alarm Time Keyboard WakeUp
,Speci c Key for PowerOn
Keyboard Wakeup Speci c Key 1-
Minix 0G
BIOS SETUP UTILITYMain Advanced PCIPnP Boot Security JUSTw00T! Power Exit
E it O ti E it t t
4.2.10 Exit ( BIOS )
-
8/6/2019 Minix780G Series Ver1.0
79/83
- -
Exit Options Exit system setupafter saving thechanges.
F10 key can be usedfor this operation.
Select Screen Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit
Save Changes and ExitDiscard Changes and ExitDiscard Changes
Load Optimal DefaultsLoad Failsafe Defaults
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
Save con guration changes and exit setup? OK CMOS RAM BIOS Cancel ESC
BIOS SETUP UTILITY
Main Advanced PCIPnP Boot Security JUSTw00T! Power ExitExit Options Exit system setup
after saving thechanges.
F10 key can be usedfor this operation.
Select Screen
Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit
Save Changes and ExitDiscard Changes and ExitDiscard Changes
Load Optimal DefaultsLoad Failsafe Defaults
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
for this
Se
SeEnter GoF1 Ge
efaultsDefaults
Save configuration changes and exit setup?
[Ok] [Cancel][Ok]
Minix 0G
Discard changes and exit setup? OK BIOS BIOS Cancel ESC
BIOS SETUP UTILITY
-
8/6/2019 Minix780G Series Ver1.0
80/83
- 0 -
Discard Changes? OK BIOS
BIOS SETUP UTILITYMain Advanced PCIPnP Boot Security JUSTw00T! Power Exit
Exit Options Exit system setupwithout saving anychanges.
ESC key can be usedfor this operation.
Select Screen Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit
Save Changes and ExitDiscard Changes and ExitDiscard Changes
Load Optimal DefaultsLoad Failsafe Defaults
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
for this
Se SeEnter GoF1 Ge
ltsults Discard changes and exit setup?
[Ok] [Cancel][Ok]
BIOS SETUP UTILITYMain Advanced PCIPnP Boot Security JUSTw00T! Power Exit
Exit Options Discards changesdone so far to any ofthe setup questions.
F7 key can be usedfor this operation.
Select Screen Select Item Enter Go to Sub Screen F1 General
top related