march 2004 67c series instrument supply...
Post on 28-Aug-2018
315 Views
Preview:
TRANSCRIPT
Bulletin 71.1:67C
D10
2656
X01
2
www.FISHERregulators.com
March 2004
67C Series Instrument Supply Regulators
✰✰✰✰✰ Compact and Light Weight
✰✰✰✰✰ Optional Integral Filter
✰✰✰✰✰ Rugged Construction
✰✰✰✰✰ Optional Internal Relief Valve
✰✰✰✰✰ No Air Loss
✰✰✰✰✰ Easy Maintenance
✰✰✰✰✰ Designed for Digital Instrumentation
W7412
W7423_1
W7426
A 67CF Series regulator used asa pilot supply regulator for theType 299H pressure regulator
A 67CF Series filterregulator shown with
optional pressure gauge
A 67CF Series regulator usedas a supply regulator fordigital instrumentation
A 67C Series instrumentsupply regulator
W8438
✰✰✰✰✰ Optional Smart Bleed™ Construction
✰✰✰✰✰ Optional Stainless Steel Construction
Bulletin 71.1:67C
2
Features
• Compact—The 67C Series regulators are engi-neered for outstanding performance in a compact,light-weight package.
• Panel Mounting—Panel mount constructionincludes spring case with 1/4-inch NPT vent,handwheel adjusting screw, and mounting nut.
• Instrument Supply Regulator—The Types 67CF,67CFR, 67CFS, and 67CFSR provide a clean airsupply to a variety of pneumatic and electro-pneumaticinstrumentation.
• Digital Instrument Supply Regulator—Designedfor the accuracy, repeatability, and hysteresis de-mands of digital instrumentation.
• Pilot Supply Regulator—Improves the accuracyof two-path control regulators by reducing inlet sensi-tivity caused by fluctuating inlet pressures.
• Pressure Loading Regulator—Provides accuracyand improved performance in dirty steam service byeliminating the need for a pilot regulator (see figure 3).
• Sour Gas Service Capability—NACE MR0175 andMR0103 compliant construction available.
• Optional Stainless Steel Construction—TheTypes 67CS, 67CSR, 67CFS and 67CFSR provide highresistance to corrosion especially beneficial in offshoreapplications.
• Full Usable Capacity—Fisher regulators arelaboratory tested. 100 percent of the publishedcapacities can be used with confidence.
• Internal Relief—The Types 67CR, 67CSR, 67CFR,and 67CFSR have an internal relief valve with a softseat for reliable shutoff with no discernible leakage.These regulators are recommended for conservingplant air.
• Smart Bleed™—Opens to exhaust downstreampressure when inlet pressure drops below outletpressure. Recommended for deadend service.
• Integral Filter—The Types 67CF, 67CFR, 67CFS,and 67CFSR have an integral filter ensuring cleandownstream air supply.
• Ease of Maintenance—No special tools arerequired to perform maintenance, and all maintenancecan be performed with the regulator in the line. Filterelements are easily replaced. The one-piece valveplug cartridge allows easy inspection and replacement.
• Rugged Construction—The 67C Series regulatorsare engineered for longer service life with minimalmaintenance requirements.
• Second Outlet—Body side outlet for pressuregauge or other uses.
• Powder Paint Coating—Types 67C, 67CR, 67CF,and 67CFR are powder paint coated, offering impact,abrasion, and corrosion resistance. Stainless steelregulators (Types 67CS, 67CSR, 67CFS and 67CFSR)are not painted.
• Corrosion Resistant Fasteners—Bolting andadjusting screw are double zinc-chromated for en-hanced corrosion resistance. Optional stainless steelbolting and adjusting screw are also available.
Introduction
The 67C Series regulators are typically used to provide constantly controlled, reduced pressures to pneumatic andelectropneumatic controllers and other instruments. These direct-operated regulators are suitable for most air orgas applications. Other applications include providing reduced pressures to air chucks, air jets, and spray guns.
Table 1. Outlet Pressure Ranges and Control Spring Data
epyT,SEGNARERUSSERPTELTUO
)rab(GISPATADGNIRPSLORTNOC
roloC lairetaM rebmuNtraP )mm(hcnI,retemaiDeriW
,RC76,C76RFC76,FC76
02ot053ot006ot0521ot0
)4,1ot0()4,2ot0()1,4ot0()6,8ot0(
epirtsneergrevlis
epirtseulbepirtsder
eriWcisuM
210T90870EG2100T95041T2100T85041T2100T06041T
531.0651.0071.0702.0
)34,3()69,3()23,4()62,5(
53ot006ot0521ot0
)4,2ot0()1,4ot0()6,8ot0(
epirtsrevliseulbder
lenocnI2100T31141T2100T41141T2100T51141T
651.0271.0702.0
)69,3()73,4()62,5(
,RSC76,SC76RSFC76,SFC76
02ot053ot006ot0521ot0051ot0
)4,1ot0()4,2ot0()1,4ot0()6,8ot0()3,01ot0(
neergepirtsrevlis
eulbderkcalb
lenocnI
210X9271C012100T31141T2100T41141T2100T51141T210X0371C01
531.0651.0271.0702.0052.0
)34,3()69,3()73,4()62,5()53,6(
Bulletin 71.1:67C
3
1. The pressure/temperature limits in this bulletin and any applicable standard or code limitation should not be exceeded.2. Repeatability is the measure of the regulator's ability to return to setpoint consistently when traveling from steady state to transient to steady state.3. Silicone is not compatible with hydrocarbon gas.4. Product complies with the material requirements of NACE MR0175. Environmental limits may apply.
Specifications
Body Size, Inlet and Outlets Connection Style
1/4-inch NPT
Construction Materials
See Table 2
Maximum Inlet Pressure (Body Rating)(1)
All except 67CS and 67CSR: 250 psig (17,2 bar)Type 67CS and 67CSR: 400 psig (27,6 bar)
Outlet Pressure Ranges
See Table 1
Maximum Emergency Outlet Pressure(1)
50 psi (3,4 bar) over outlet pressure setting
Capacities
See Table 3 and Capacity Information section
Wide-Open Flow Coefficients
Main Valve: Cg: 11.7; Cv: 0.36; C1: 32.2;Internal Relief Valve: Cg: 1.45; Cv: 0.045; C1: 32.8
IEC Sizing Cooefficients
Main Valve: XT: 0.66; FL: 0.89; FD: 0.50
Accuracy
Inlet Sensitivity: Less than 0.2 psig (0,014 bar)change in outlet pressure for every 25 psig(1,72 bar) change in inlet pressureRepeatability: 0.1 psig (0,0069 bar)(2)
Air Consumption: testing repeatedly showsno discernible leakage
Type 67CR, 67CSR, 67CFR, and 67CFSR InternalRelief Performance
Low capacity for minor seat leakage only; otheroverpressure protection must be provided if inletpressure can exceed the maximum pressure ratingof downstream equipment or exceeds maximumoutlet pressure rating of the regulator.
Approximate Unit Weight
Types 67C, 67CR, 67CF, and 67CFR:1 pound (0,5 kg)Types 67CS and 67CSR:2.5 pounds (1,2 kg)Types 67CFS and 67CFSR:4 pounds (1,8 kg)
Smart Bleed™ Check Valve Setpoint
6 psi (0,4 bar) differential
Pressure Registration
Internal
Drain Valve and Spring Case Vent Location
Aligned with inlet standard, other positions optional
Regulator Temperature Capabilities
With Nitrile (NBR)Standard Bolting: -20 to 180°F (-29 to 82°C)Stainless Steel Bolting: -40 to 180°F (-40 to 82°C)With Fluoroelastomer (FKM):0 to 300°F (-18 to 149°C)With Silicone (VMQ)(3) Diaphragm and LowTemperature bolting: -60 to 180°F (-51 to 82°C)With Gauges: -20 to 180°F (-29 to 82°C)
Type 67CF, 67CFR, 67CFS, and 67CFSR FilterCapabilities
Free Area: 12 times pipe areaMicron Rating: Cellulose Element: 40 micronsGlass Fiber Element: 5 micronsStainless Steel Element: 40 microns
Options
All Types• Handwheel adjusting screw• Inlet screen• NACE MR0175(4) or NACE MR0103 construction• Panel mount (includes spring case with 1/4-inch
vent, handwheel, and panel mounting nut)• Closing cap (available on spring case with
1/4-inch NPT vent)• Fluoroelastomer (FKM) elastomers for high
temperatures and/or corrosive chemicals• Silicone (VMQ) elastomers for cold temperatures• Fixed Bleed Restriction• Triple scale outlet pressure gauge (brass or
stainless steel)• Stainless steel stem on the valve plug• Tire valve or pipe plug in second outlet
Type 67CFR only• Smart Bleed™ internal check valve
Types 67CF and 67CFR only• Stainless steel drain valve
Bulletin 71.1:67C
4
Figure 2. 67C Series Operational Schematics
Table 2. 67C Series Construction Materials
INLET PRESSURE
OUTLET PRESSURE
ATMOSPHERIC PRESSURE
W7433
TYPE 67CFR OR 67CFSR
TYPE 67CF OR 67CFS
TYPE 67C OR 67CS
TYPE 67CR OR 67CSR
SMART BLEED™ OPTIONTYPE 67CFR ONLY
LAIRETAMEPYT
RC76dnaC76 RFC76dnaFC76 RSC76dnaSC76 RSFC76dnaSFC76
dnaydoBesaCgnirpS )083yollA/58BMTSA(munimulA leetssselniatSM3FC/M8FC
etalPmottoB leetssselniatS613 --- leetSsselniatS613 ---
evlaVdnatsoPrehsuPegdirtraC niserretseyloP
taeSgnirpSreppU leetSdetalp-cniZ leetssselniatS613
,taeSgnirpSrewoLetalPmgarhpaiD munimuladetaocnoisrevnocetamorhC leetssselniatS613
gnirpSlortnoC )ECAN(lenocnIroleetSdetalP lenocnI
gulPevlaV,gulpelirtiNhtiwmetsssarB
ro,gulpremotsaleoroulFroelirtiNhtiwmetsmunimulAgulpremotsaleoroulFroelirtiNhtiwmetsleetssselniatS
htiwmetsleetssselniatS613gulpremotsaleoroulFroelirtiN
gnirpSevlaV )ECAN(lenocnIroleetssselniatS lenocnI
mgarhpaiDsgniR-Odna enociliSro,remotsaleoroulF,elirtiN )1(
steksaGdnataeStfoS remotsaleoroulFroelirtiN
gnitsujdA,gnitloBtunkcoL,wercS leetssselniatSroleetsdetalp-cniZ leetssselniatS613
leehwdnaH leehwdnahniserhtiwwercsleetsdetalp-cniZ
reniateRretliF --- leetSdetalP --- 613leetssselniatS
tnemelEretliF --- ,esolulleCleetssselniatSro,rebifssalG --- rorebifssalG
leetssselniatS613
evlaVniarD --- rossarBleetssselniatS --- roleetSsselniatS613
leetssselniatS8-81
llewpirD --- munimulA)083yollA/58BMTSA( --- leetssselniatSM3FC/M8FC
.)RSFC76,RFC76,RSC76,RC76(feilerlanretnihtiwelbaliavaylnomgarhpaidenociliS.1
Bulletin 71.1:67C
5
Principle of Operation (figure 2)
Downstream pressure is registered internally on thelower side of the diaphragm. When the downstreampressure is at or above the set pressure, the valve plugis held against the orifice and there is no flow throughthe regulator. When demand increases, downstreampressure drops slightly allowing the spring to extend,moving the stem down and the valve plug away fromthe orifice. This allows flow through the regulator.
Internal Relief (Types 67CR, 67CSR,67CFR, and 67CFSR)
If for some reason, outside of normal operatingconditions, the downstream pressure exceeds the setpoint of the regulator, the force created by thedownstream pressure will lift the diaphragm until thediaphragm is lifted off the relief seat. This allows flowthrough the token relief. The relief valve on theType 67CR, 67CSR, 67CFR, or 67CFSR is an elastomerplug that prevents leakage of air from the downstreamto atmosphere during normal operation, therebyconserving plant air.
Smart Bleed™ Airset
In some cases, it is desired to exhaust downstreampressure if inlet pressure is lost or drops below thesetpoint of the regulator. For example, if the regulator isinstalled on equipment that at times has no flowdemand but is expected to backflow on loss of inletpressure. The Type 67CFR can be ordered with theSmart Bleed™ option which includes an internal checkvalve for this application. During operation, if inletpressure is lost, or decreases below the setpoint of theregulator, the downstream pressure will back flowupstream through the regulator and check valve. Thisoption eliminates the need for a fixed bleed downstreamof the regulator, thereby conserving plant air.
Overpressure Protection
The 67C Series regulators have maximum outletpressure ratings that are lower than their maximuminlet pressure ratings. A pressure relieving or pressurelimiting device is needed if inlet pressure can exceedthe maximum outlet pressure rating. Refer to theCapacity Information section and the Wide-OpenCoefficients for Relief Valve Sizing in the Specifica-tions on page 3 to determine the required relief valvecapacity.
Type 67CR, 67CSR, 67CFR, and 67CFSR regulatorshave a low capacity internal relief valve for minor seat
leakage only. Other overpressure protection must beprovided if the maximum inlet pressure can exceed themaximum pressure rating of the downstream equipmentor exceeds maximum outlet pressure rating of theType 67CR, 67CSR, 67CFR, or 67CFSR regulator.
Capacity Information
Table 3 shows the air regulating capacities of the67C Series regulators at selected inlet pressures andoutlet pressure settings. Flows are shown in scfh(at 60°F and 14.7 psia) and in m³/h(n) (at 0°C and1,01325 bar) of air.
Note
The 67C Series regulators may be sizedfor 100% flow using capacities as shownin table 3. It is not necessary to reducepublished capacities.
To determine the equivalent capacities for other gases,multiply the table capacity by the following appropriateconversion factor: 1.29 for 0.6 specific gravity naturalgas, 0.810 for propane, 0.707 for butane, or 1.018 fornitrogen. For gases of other specific gravities, dividethe table capacities by the square root of the appropri-ate specific gravity. To find wide-open flow capacitiesfor relief sizing at any inlet pressure, perform one ofthe following procedures. Then, if necessary, convertusing the factors provided above.
For critical pressure drops (absolute outlet pressureequal to or less than one-half of absolute inlet pres-sure), use the following formula:
Q = (P1)(Cg)
For pressure drops lower than critical (absoluteoutlet pressure greater than one-half of absolute inletpressure), use the following formula:
Q 520GT
C P SIN g 1=⎛
⎝⎜⎜
⎞
⎠⎟⎟
34171 1C
PP
DEG∆
where,
Q = gas flow rate, scfhP1 = absolute inlet pressure, psia (P1 gauge + 14.7)Cg = gas sizing coefficientG = specific gravity of the gasT = absolute temperature of gas at inlet, °Rankine
C1 = flow coefficient (Cg ÷ Cv)∆P = pressure drop across the regulator, psi
Then, if capacity is desired in normal cubic meters perhour (at 0°C and 1,01325 bar), multiply scfh by 0.0268.
Bulletin 71.1:67C
6
ERUSSERPTELTUO=TRAPGNIRPS,EGNAR,ROLOCDNAREBMUN
GISP rab( )
TELTUO,ERUSSERP
(GISP rab )
,ERUSSERPTELNI(GISP rab )
(HFCSNISEITICAPAC m3 ))n(h/ RIAFO
RSC76dna,SC76,RC76,C76sepyT RSFC76dna,SFC76,RFC76,FC76sepyT
poorD%01 poorD%02 poorD%01 poorD%02
)4,2ot0(53ot0)revliS(2100T95041T
2100T31141T)epirtSrevliS(
51 )0,1(
0557001051052004
)4,3()2,5()9,6(
)3,01()2,71()6,72( )2(
0520430340860031093
)07,6()11,9()5,11()2,81()8,43()5,01(
034016008002100910581
)5,11()3,61()4,12()2,23()9,05()0,05(
052003033004054--
)07,6()40,8()48,8()7,01()1,21(
--
034096000100610081--
)5,11()5,81()8,62()9,24()2,84(
--
02 )4,1(
0557001051052004
)4,3()2,5()9,6(
)3,01()2,71()6,72( )2(
01302402606905510021
)13,8()3,11()6,61()7,52()5,14()2,23(
064007049054105120572
)3,21()8,81()2,52()9,83()6,75()7,37(
05303505700410552--
)83,9()2,41()1,02()5,73()3,86(
--
005028001100610072--
)4,31()0,22()5,92()9,24()3,27(
--
53 )4,2(
0557001051052004
)4,3()2,5()9,6(
)3,01()2,71()6,72( )2(
093095077002100220582
)5,01()8,51()6,02()2,23()9,85()4,67(
0940580511057100720543
)1,31()8,22()8,03()9,64()3,27()5,29(
09304604805410542--
)5,01()1,71()5,22()9,83()6,56(
--
005028001105610072--
)4,31()0,22()5,92()2,44()3,27(
--
)1,4ot0(06ot02100T85041T)epirtseulB(
)eulB(2100T41141T
53 )4,2(
0557001051052004
)4,3()2,5()9,6(
)3,01()2,71()6,72( )2(
0130440650870541077
)13,8()8,11()0,51()9,02()9,83()6,02(
044076009053100220052
)8,11()0,81()1,42()2,63()0,95()0,76(
03300500705010002--
)48,8()4,31()8,81()1,82()6,35(
--
074037000105510062--
)6,21()6,91()8,62()5,14()7,96(
--
06 )1,4(
57001051052004
)2,5()9,6(
)3,01()2,71()6,72( )2(
025057001105020023
)9,31()1,02()5,92()9,45()8,58(
0270501007105820034
)3,91()1,82()6,54()4,67()511(
02507700110542--
)9,31()6,02()5,92()6,56(
--
027000100610572--
)3,91()8,62()9,24()7,37(
--
)6,8ot0(521ot02100T06041T)epirtsdeR(
)deR(2100T51141T
08 )5,5(
001051052004
)9,6()3,01()2,71()6,72( )2(
0050570021019
)4,31()1,02()2,23()4,42(
008002105020073
)4,12()2,23()9,45()2,99(
0350870521--
)2,41()9,02()5,33(
--
08700210022--
)9,02()2,23()9,85(
--
521 )6,8(051052004
)3,01()2,71()6,72( )2(
00906510022
)1,42()8,14()0,95(
052105420534
)5,33()6,56()711(
0090561--
)1,42()2,44(
--
05110542--
)8,03()6,56(
--
)6,8ot0(051ot0 )1(
)kcalB(210X0371C01
08 )5,5(052004
)2,71()6,72( )2(
055004
)7,41()7,01(
00210011
)2,23()5,92(
055--
)7,41(--
0021--
)2,23(--
531 )3,9(052004
)2,71()6,72( )2(
079048
)0,62()5,22(
00810532
)2,84()0,36(
0011--
)5,92(--
0081--
)2,84(--
051 )3,01(052004
)2,71()6,72( )2(
0011049
)5,92()2,52(
05810052
)6,94()0,76(
0011--
)5,92(--
0581--
)6,94(--
ylnoRSFC76dnaSFC76,RSC76,SC76sepyTrofelbaliavA.1.RSC76dnaSC76sepyTnoelbaliavaylno)rab6,72(gisp004fomumixamahtiw)rab2,71(gisp052evobaserusserptelnI.2
Table 3. Capacities
670 Series Panel-Mounted LoadingRegulators (figure 4)
The 670 Series panel-mounted loading regulators arecompact, rugged units used primarily for manuallyloading pressure-balanced gas regulators and providingmanual control for diaphragm actuator control valves.Applications include remote control of gas pressure toburners in refineries, power plants, and variousprocess furnaces.
Three basic panels are available within the productline, each having one 67C Series pressure regulator
connected to one or two gauges and a changeovervalve. A single gauge typically shows loadingpressure to the control valve. For more informationsee bulletin 62.3:670.
Ordering Information
When ordering, complete the Ordering Guide on page12. Refer to the Specifications on page 3. Review thedescription to the right of each specification and theinformation in each referenced table or figure. Specifyyour choice whenever a selection is offered.
Bulletin 71.1:67C
7
Figure 3. 67C Series Regulator Used to Pressure Load a 92P Steam Regulator
A 67C SERIES PRESSURE LOADING REGULATOR USED WITH THE TYPE 92P STEAM REGULATOR ELIMINATES THE NEED FOR APILOT REGULATOR. THIS PROVIDES HIGH ACCURACY AND IMPROVED PERFORMANCE IN DIRTY STEAM SERVICE.
67C SERIESFILTER REGULATOR
UPSTREAM PRESSURE
LOADING PRESSURE
DOWNSTREAM PRESSURE TYPE 92PSTEAM REGULATOR
W7434
Figure 4. 670 Series Typical Panel Layouts
1-GAUGE PANEL 2-GAUGE PANEL 2-GAUGE PANEL WITHCHANGEOVER VALVE
Bulletin 71.1:67C
8
Figure 5. Types 67C, 67CR, 67CS, and 67CSR Dimensions
DIMENSIONS FOR PANEL MOUNT OPTION WITHHAND WHEEL AND 1/4-INCH SPRING CASE VENT
AMAX
D
2.37(60)MAX
C
PANEL0.12 TO 0.25(3,0 TO 6,5)
4.56(116)
2.92(74)
OPTIONAL GAUGE
SIDE OUTLET TAPPED1/4-INCH NPT
1/4-INCH NPT VENT
0.72-INCH (1,8 mm)SPRING CASEPANEL BOSS
1.46(37)
DIMENSIONS WITH CLOSING CAPAND 1/4-INCH SPRING CASE VENT
2.56(65)
1.43(36)
INLET CONNECTION1/4-INCH NPT
OUTLETCONNECTIONS1/4-INCH NPT
A
CLOSING CAP
B
AMAX
4.56(116)
1.46(37)
2.92(74)
OPTIONAL GAUGE
SIDE OUTLET1/4-INCH NPT
STANDARD DIMENSIONSFOR GAUGE OPTION
STANDARD DIMENSIONS
2.56(65)
0.50(13)
OUTLETCONNECTIONS1/4-INCH NPT
INCHES(mm)
EPYTSNOISNEMIDDRADNATS
HTIWNOISNEMIDPACGNISOLC
SNOISNEMIDLEEHWDNAHHTIWNOITPOTNUOMLENAP
A B A A C D
RC76,C76 )98(05.3 )83(15.1 )711(06.4 )911(96.4 )72(80.1 )95(33.2
RSC76,SC76 )501(31.4 )14(26.1 )521(39.4 )721(00.5 )92(41.1 )76(56.2
INLET CONNECTION1/4-INCH NPT
Bulletin 71.1:67C
9
Figure 6. Types 67CF and 67CFR Dimensions
DRAIN VALVE POSITIONS
DIMENSIONSFOR GAUGE OPTION STANDARD DIMENSIONS
B2699_A
3.50(89)
3.50(89)
4.56(116)
1.48(38)
3.00(76)
2.56(65)
0.62(16)
2.87(73)
2.25(57)
0.69(18)OPTIONAL GAUGE
MOUNTING HOLESFOR 5/16-INCHDIAMETER BOLTS
SIDE OUTLET1/4-INCH NPT
INLET CONNECTION1/4-INCH NPT
INCHES(mm)
OUTLETCONNECTIONS1/4-INCH NPT
B2699_B
VENT POSITIONS
INLET OUTLET
GA
UG
E
VENT POSITION 3
VENT POSITION 4
VENT POSITION 1(STANDARD)
VENT POSITION 2
B2699_C
DRAIN VALVEPOSITION 3
DRAIN VALVEPOSITION 2
DRAIN VALVEPOSITION 1(STANDARD)
DRAIN VALVEPOSITION 4
INLET OUTLET
GA
UG
E
B2699_D
Figure 7. 67C Series Vent and Drain Valve Positions
Bulletin 71.1:67C
10
DIMENSIONS FOR PANEL MOUNT OPTIONWITH HAND WHEEL AND 1/4-INCH SPRING CASE VENT DIMENSIONS FOR CLOSING CAP OPTION
WITH 1/4-INCH SPRING CASE VENT
INCHES(mm)
Figure 8. Types 67CF and 67CFR Dimensions (continued)
2.56(65)
1.43(36)
2.87(73)
2.25(57)
0.69(18)
MOUNTING HOLESFOR 5/16-INCHDIAMETER BOLTS
INLET CONNECTION1/4-INCH NPT
OUTLETCONNECTIONS1/4-INCH NPT
4.69(119)
CLOSING CAP
3.50(89)
4.78(121)MAX
4.56(116)
1.48(38)
3.00(76)
OPTIONAL GAUGE
SIDE OUTLET TAPPED1/4-INCH NPT
1/4-INCH NPT VENT
0.72-INCH (1,8 mm)SPRING CASEPANEL BOSS
2.41(61)
2.37(60)MAX
1.14(29)
PANEL0.12 TO 0.25(3,0 TO 6,5)
B2700_A
Figure 9. Spacer Dimensions and Installation Schematic
SPACER(FOR INSTALLING A 67CF SERIESREGULATOR IN AN EXISTINGINSTALLATION IF THE MOUNTINGBOLTS ARE TOO LONG)
0.50(12.7)
0.18(4,57)
0.32(8.12)
SPACER OUTER DIAMETER SPACER WIDTH ANDINNER DIAMETER
IDOD
B2697_B
B2697_A
B2700_B
Bulletin 71.1:67C
11
STANDARD DIMENSIONS (INCLUDING CLOSING CAP) STANDARD DIMENSIONS (INCLUDING CLOSING CAP)
DIMENSIONS FOR PANEL MOUNT OPTION WITH HANDWHEELDIMENSIONS WITHOUT CLOSING CAP
Figure 10. Types 67CFS and 67CFSR Dimensions
4.56(116)
3.00(76)
1.48(38)
4.93(125)
1.14(29)
4.00(102)
OPTIONALGAUGE
VENT 1/4 NPT
1.43(36)
2.56(65)
0.62(16)
CLOSINGCAP
0.69(18)
1/4-INCH NPT INLETCONNECTION
MOUNTING HOLESFOR 5/16-INCH
DIAMETER BOLTS
2.25(57)
2.87(73)
INCHES(mm)
1/4-INCH NPTOUTLET
CONNECTIONS
1/4-INCH NPTINLET CONNECTION
2.37(60)MAX
PANEL0.12-0.25(3-6,5)
2.65(67)
4.13(105)
5.00(127)
MAXIMUM
INCHES(mm)
MAXIMUM
Bulletin 71.1:67C
Fisher is a mark owned by Fisher Controls International, Inc., a business of Emerson Process Management. The Emerson logo is a trademark and service mark of Emerson Electric Co. All other marks are theproperty of their respective owners.
The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not to be construed as warranties or guarantees, expressor implied, regarding the products or services described herein or their use or applicability. We reserve the right to modify or improve the designs or specifications of such products at any time without notice.
Fisher does not assume responsibility for the selection, use or maintenance of any product. Responsibility for proper selection, use and maintenance of any Fisher product remains solely with the purchaser.
For information, contact Fisher:Marshalltown, Iowa 50158 USAMcKinney, Texas 75070 USA28320 Gallardon, France40013 Castel Maggiore (BO), ItalySao Paulo 05424 BrazilSingapore 128461
www.FISHERregulators.com ©Fisher Controls International, Inc., 2001, 2004; All Rights Reserved
Ordering GuideType (Select One)� Type 67C (aluminum without internal relief)***� Type 67CR (aluminum with internal relief)***� Type 67CS (stainless steel without internal relief)***� Type 67CSR (stainless steel with internal relief)***� Type 67CF (aluminum with filter and without internal relief)***� Type 67CFR (aluminum with filter and internal relief)***� Type 67CFS (stainless steel with filter and without
internal relief)***� Type 67CFSR (stainless steel with filter and internal relief)***
Quantity (Specify)
Spring Case Style (Select One)� Drilled hole vent (67C, 67CR, 67CF, 67CFR standard)***� 1/4-inch NPT vent (67CS, 67CSR, 67CFS, 67CFSR standard)***� Single hole panel mount***
Adjusting Screw (Select One)� Square head (67C, 67CR, 67CF, 67CFR standard)***� Square head with closing cap (67CS, 67CSR, 67CFS,
67CFSR standard)***� Handwheel***
Outlet Pressure Range (Select One)� 0 to 20 psig (0 to 1,4 bar)***� 0 to 35 psig (0 to 2,4 bar)***� 0 to 60 psig (0 to 4,1 bar)***� 0 to 125 psig (0 to 8,6 bar)***� 0 to 150 psig (0 to 10,3 bar) (67CS, 67CSR, 67CFS, 67CFSR
only)***
Diaphragm, O-Rings, and Valve Plug (Select One)� Nitrile (NBR) (standard)***� Fluoroelastomer (FKM)**� Silicone (VMQ) diaphragm, O-rings, and nitrile valve plug*
Filter Material (Select One)� Cellulose (40 microns)(67CF, 67CFR standard)***� Glass (5 microns)***� Stainless steel (40 microns)(67CFS, 67CFSR standard)***
Drain Valve (Select One)� Brass (67CF, 67CFR standard)***� Stainless steel (67CFS, 67CFSR standard)***
Drain Valve Location (Select One)� Position 1 - Aligned with inlet (standard)***� Position 2� Position 3� Position 4
Spring Case Vent Location (Select One)� Position 1 - Aligned with inlet (standard)***� Position 2� Position 3� Position 4
Fixed Bleed for Type 67CR, 67CSR, 67CFR, or 67CFSR (Optional)� Yes**
Smart Bleed™ Internal Check Valve Airset (Optional - 67CFR only)� Yes**
Second Outlet (Select One)� Open (67C, 67CR, 67CF, 67CFR standard)***� Plugged with pipe plug (67CS, 67CSR, 67CFS, 67CFSR
standard)***� Tire Valve***� Pressure Gauge (see below)
Triple Scale Pressure Gauge (Optional)� Brass Gauge or � Stainless Steel Gauge� 0 to 30 psig/0 to 0.2 MPa/0 to 2 bar***� 0 to 60 psig/0 to 0.4 MPa/0 to 4 bar***� 0 to 160 psig/0 to 1.1 MPa/0 to 11 bar***
NACE MR0175 Construction (Optional)(1)
� Yes (not available with gauge)**1. Product complies with the material requirements of NACE MR0175.
Environmental limits may apply.
NACE MR0103 Construction (Optional)� Yes (not available with gauge)**
Replacement Parts Kit (Optional)� Yes, send one replacement parts kit to match this order.
ediuGredrOkciuQsrotalugeRrehsiF
*** tnempihSrofelbaliavAylidaeR-dradnatS
** tnempihSrofemiTlanoitiddAwollA-dradnatS-noN
* epS .straPdekcotS-noNmorfdetcurtsnoC,redrOlaictlusnoC .ytilibaliavArofevitatneserpeRselaSrehsiFruoY
tnenopmocehtybdenimretedsideredrogniebtcudorpehtfoytilibaliavA.noitcurtsnocdetseuqerehtrofemitgnippihstsegnolehthtiw
Specification WorksheetApplication (Please designate units):Specific Use Line Size Gas Type and Specific Gravity Gas Temperature Does the Application Require Overpressure Protection?� No � Yes, if so, which is preferred:� Relief Valve � Monitor Regulator � Shutoff Device
Is overpressure protection equipment selection assistancedesired?
Pressure (Please designate units):Maximum Inlet Pressure (P1max) Minimum Inlet Pressure (P1min) Downstream Pressure Setting(s) (P2) Maximum Flow (Qmax)
Performance Required:Accuracy Requirements? Need for Extremely Fast Response?
Other Requirements:
top related