integrated intelligent transportation systems (its)
Post on 09-Jan-2017
31 Views
Preview:
TRANSCRIPT
1
Faculty of Science and Engineering
Department of Civil Engineering
Babagana Sheriff ( M.Sc. Civil Engineering)
Ramat Polytechnic Maiduguri, Nigeria
An Implementation of Integrated ITS Solution supporting Mobility as a Service within West
Midlands Region, UK in Collaboration of Integrated Transport Authority.
1.0 Integrated ITS Solution from State of Art Review
1.1 Introduction According to United State Department of Transport (USDT, 2011) Intelligent Transportation
Systems (ITS) can be referred to as the application of advanced information and communications
technology to surface transportation in order to achieve enhanced safety and mobility while
reducing the environmental impact of transportation. The addition of wireless communications
offers an influential and transformative chances to create transportation connectivity that
supplementary enables cooperative systems and dynamic data exchange using a broad range of
advanced systems and technologies. In this report, intelligent transport system ITS architecture
and model established by several researchers all over the world has been has considered, studied
and critically reviewed in-depth in order to apply to the current project. Roles of Global
Positioning System (GPS) and Map Matching Algorithms in ITS also been studied in order to
develop a new mobility concept that enhances Policing/Enforcing Traffic Regulations System
that support Mobility-as-a-Service (MaaS) within the West Midlands in Collaboration of
Integrated Transport Authority (ITA). The system that will improves transportation through the
safe and well-organized movement of people, goods, and information, with better mobility and
fuel efficiency, less pollution, and improved operating efficiency that must be accommodating
and fair in serving the interests of West Midlands Integrated Transport Authority (ITA) and
enuances the present and future economic efficiency of individuals, organizations, and the
economy as a whole.
Balaji and Srinivasan, (2011) for traffic management operations used type-2 fuzzy decision
module which offers more autonomy to the system and less manpower requirement. However,
Mulay et al. (2013) also highlighted the use of traffic management system which provides
facility of congestion detection and management, IPTS and signal synchronization. This facility
that dictate congestion for proper management is noted and may be considered in deployment of
new proposed integrated system development in West Midland. However, Advanced Traffic
Management System developed by Balaji and Srinivasan (2011) provides only the traffic signal
control for the management of traffic also Logi and Ritchie (2001) and Ossowski et al. (2005)
2
introduced Decision Support System (DSS) for traffic management. The former was based on the
knowledge based system while the later was based on multi-agent technology. Logi and Ritchie
(2001) used Traffic Congestion Management (TCM) method that can properly estimate current
traffic conditions using the result of a static assignment based on historical O-D data that
represent daily traffic pattern under different conditions. This approach is quite fast but the
problem is inaccurate for assessment of the current demand. Adoption of dynamic method
assignment that detecate images of traffic violators and interprete the nature of the violation,
create file and send to law enforcement agengiies for procecution will be better approach for the
current demand. System established by Logi and Ritchie (2001), Hernandez et al. (2002),
Ossowski et al. (2005) and Mulay et al. (2013) were capable of managing different traffic
incidents via different approaches, nevertheless the system established by Balaji and Srinivasan
(2011) was traffic signal control system to optimize the signal traffic to decrease congestion.
Zhenlin et al. (2012) studied the efficiency of the Beijing Intelligent Traffic Management System
(ITMS)., they found that efficiency of transportation facilities has significantly increased after
the implementation of Advanced Traffic Management System. The study by Faghri and Hamad
(2002) was more of a basic study, as they did not develop any system but only studied the use of
GPS in traffic management and found out that GPS data to be 50% more efficient in terms of
manpower. This shows the significance of GPS technology in traffic management operations.
A variety of intelligent transport system (ITS) applications and services such as road control,
fleet management, road user charging, accident and emergency response, bus arrival information
at bus stop stations, and location based services (LBS) require location information. For
example, buses equipped with a navigation system can determine their locations and direct
information back to a control centre allowing bus operators to forecast the arrival of buses at bus
stop stations and hereafter improve the service level of public transport systems. The accuracy
for horizontal positioning of such ITS utilization is ranged between 1m to 40 m (positioning
accuracy of 2D at 95% of the time), with comparatively high requirements on continuity,
integrity and system availability. Though most ATT services (navigation and road guidance,
distance- based road pricing etc.) needs a 1HZ of sample frequency, some ATT service
(including bus arrival information at bus stop stations) only needs 30 HZ of sample frequency or
higher.
In the few years ago, the Global Positioning System (GPS) has proven itself as a main
positioning technology for providing locational data for ITS applications including mobile
phones equipped with GPS for numerous applications. Zito et al. (2005) provided a decent
overview for GPS use as an intelligent tool for vehicle-highway systems. Deduced calculating
sensors - usually stated as Dead-Reckoning (DR) sensors - (comprise gyroscope and odometer)
are usually used to link any gaps in GPS positioning (Kubrak, et al., 2006). 3-D road network
data are used to determine the spatial reference of the vehicle position through a procedure
recognized as map matching. For example, the accuracy and accessibility of positioning data
using mobile phones will be significantly increased if the navigation task of mobile phones is
supported by GPS, DR, and spatial road network data integrated by a map matching algorithm.
The map matching algorithm overall function is to recognize the precise road section on which
the vehicle is travelling and to regulate the vehicle position on that section (Quddus et al, (2003),
Greenfeld, (2002)). Map matching system in any navigation segment is vital to meet the stated
3
needs set for that specific service. Nevertheless, the map matching algorithm function rely on the
features of the inputs data (Chen et al. 2005).
1.2 ITS System Architectures Around the World According to Yokota, T., and Weiland R.J., (2004), advanced countries around the world have
taken the lead in establishing ITS system architectures. These comprise the U.S., the European
Union, and Japan. Numerous other countries, both developed and developing, have produced
their own national ITS architectures according to their level of development based on their suited
architectures. Furthermore, the International Organization for Standardization (ISO) includes a
working group on ITS architecture (WG1) in its technical committee on ITS (TC204). The
physical architecture comprise user need for some countries were reviewed in following
headings in order to carefully study and incorporate the suitable user needs to the deploymen of
new integrated ITS solution proposed for West Midlands Integrated Transport Authority (ITA).
1.2.1 U.S. National ITS Architecture As highlighted by Yokota, T., and Weiland R.J., (2004), U.S. was the first country to
establinational ITS architecture, beginning in the early 1990s. The U.S. architecture has 33 user
services in eight User Service, see appendix A for the llist of user services. The principal
elements in the physical architecture are entities and architecture flows that connect these entities
into an overall structure. The physical architecture assigns processes from the logical architecture
to subsystems, and groups data flows from the logical architecture into architecture flows. These
flows and the corresponding communication requirements define the interfaces which are a main
focus of ITS standards development in the U.S. (see Figure 1 & 2).
Figure 1: Very High Level Logical Architecture of the U.S. National ITS Architecture
Source: Yokota, T., and Weiland R.J., (2004)
Provide Electronic Payment Services
Manage Commercial
Vehicles
Provide Vehicle
Monitoring &Control
Financial Institution
Payment Request
Payment
Route Request
Route Information
Transit Schedules
Transit Requests
Emergency Telecom System
Archived Data User System
Storage Facility
Archive Data
Route Information
Priority Requests
Incident Notification
Incident Information
Traffic
Traffic Information
Vehicle Status
Basic Commercial
Vehicle
Basic Vehicle
Provide Driver & Traveler Services
Manage Transit
Manage Traffic
Manage Emergency Services
Manage Archived
Data
Manage Maintenance
& Construction
4
Figure 2: US ITS Architecture
Source James et al.,(2010)
1.2.2 European ITS Framework Architecture
The European ITS Framework Architecture (informally called FRAME) is a project of the EU
Directorate on Information Society Technology and is one of the vital efforts of the Fifth
Framework research program. FRAME, which is still in progress, will deliver a second
generation architectural approach, based on the original European ITS Architecture called
KAREN (for Keystone Architecture Required for European Networks). (Yokota, T., and
Weiland R.J.,2004). The deployment of the propsed new ITS solution is designed based on the
FRAME guidelines. Figure. shows the European ITS framework architecture model and see
Appendix B for its list of user needs .
Figure 3: European ITS Framework Architecture
Source: James et al.,(2010)
5
1.2.3: Japanese ITS System Architecture According to Yokota, T., and Weiland R.J., (2004). the Japanese ITS System Architecture was
accomplished in 1999 via the collaborative efforts of five government ministries involved in ITS,
also in collaboration with VERTIS (now ITS Japan). The Japanese ITS architecture comprises an
enumeration of user services as shown in Appendix C and a physical architecture also shown in
Figure. 4.
http://www.its-jp.org/english/arch_e/doc/summary.pdf, p20
Figure 4: Subsystem Interconnect Diagram from Japanese Physical ITS Architecture
Source: Yokota, T., and Weiland R.J., (2004).
1.2.4: Australia architecture
According to James et al.,(2010), Australia, architecture was developed in the form of a multi-
modal ITS future big picture, with the aim to improve the future development and deployment of
6
ITS services within Australia by providing a framework for the development of standards,
promoting integration of systems and providing a basis for education. The figure 5 below shows
the ITS Architecture.
Figure 5 Australian ITS architecture
Source: James et al.,(2010)
1.2.5 Canada ITS architecture
According to James et al.,(2010), the Canadian ITS architecture was developed from the
US model, mainly due to the benefits of having closely related transport systems that
supplement each other. Though there are a number of differences because of the Canadian
environment. The logical architecture of the Canadian ITS architecture was developed
in parallel with the physical architecture, unlike the US where the development of the
physical architecture was based on the logical architecture. The Canada ITS architecture is
Shown in figure 6.
Figure 6: Canada ITS architecture
Source: James et al.,(2010)
1.2.6 ISO ITS Reference Architecture As highlighted by Yokota, T., and Weiland R.J., (2004), the ITS technical committee of the
International Organization for Standardization (ISO/TC204) has established an architecture that
7
assist to define ITS standards. Since it is relatively uncomplicated architecture, it has also
served as a base model for the development of other ITS architectures. The principal features of
the ISO architecture are a reference model for other architectures and has collection of user
services. The user services are presented in table 1 and the depiction of ISO Core ITS
Architecture Reference Model is also shown in figure 7.
Table 4 ISO ITS Architecture Service Domains and Service Groupings
8
Source: Yokota, T., and Weiland R.J., (2004).
Figure 7: High-Level Depiction of ISO Core ITS Architecture Reference Model
Source: Yokota, T., and Weiland R.J., (2004).
A recent study by the UK Government’s Office of Science and Innovation, which studied how
upcoming intelligent infrastructure would evolve to support transportation over the next 50 years
looked at a range of new technologies, systems and services that may appear over that period
(UK DfT, 2006). One important class of technology that was recognized as having a important
role in delivering future intelligence to the transport sector was wireless sensor networks and in
precise the fusion of fixed and mobile networks to aid in delivering a safe, sustainable and robust
9
future transportation system based on the improved collection of data, its processing and
dissemination and the intelligent use of the data in a fully connected environment. The important
innovations in wireless and digital electronics are beginning to support many applications in the
areas of safety, environmental and emissions control, driving assistance, diagnostics and
maintenance in the transport domain. In the last few years, the emergence of many new
technologies that can potentially have major impacts on Intelligent Transportation Systems (ITS)
had been recorded (Tully, 2006).
According to research only few prevailing map matching algorithms offer a meaningful
validation technique. Kim et al. (2000) indicated the significant of using code-based DGPS to
dictate accurate vehicle positions. However, the performance of DGPS is highly affected by
signal multipath, amongst other factors, and its effectiveness varies depending on the
surrounding environments. The typical precision of DGPS is on the order of 0.5m to 5m (95%)
(US DoA, 2003). Subsequently, the vehicle positions obtained from DGPS may not be proper to
derive the reference trajectory of the vehicle. Quddus et al (2004) used high accuracy GPS
carrier phase observations in order to validate the performance of a map matching algorithm.
However, it is not possible to attain GPS carrier phase observations in dense urban areas due to
inherent problems related with GPS signal masking and multipath error.
1.3: Bus Priority Architecture: A London case study According to Grant-Muller, S. and Usher, M., (2014), the leading city in UK in growth and
implementation of bus priority at traffic signals is London. Decentralised communications
system with priority requests from the bus to the traffic signal controller via the roadside beacon
is used. Again, this method was preferred because: i) the communication process was already developed from the Automatic Vehicle
Location (AVL) centre to buses and allowed bus priority requests to communicate
similarly;
ii) the London system uses ‘precise’ bus location for priority relatively close to the junction
because of high bus journey time variability AVL beacons could then replace the
transponder/bus detector system). . Figure 8 shows the AVL based bus priority
architecture in London
`
Figure 8. AVL based bus priority architecture in London
10
……………………………………………………………………………………………
According to (Hounsell et al., 2000), the bus priority architecture works as when the system
control centre communicates with the bus using Band III radio at every 30 seconds to get its
current position, the system control centre then detect the priority level request (PLR) of the bus
based on its lateness, the determination of lateness is carried out for every bus at the priority
determination points (PCP) identified on the route. The priority level request (PLR) determined
is then sent back to the bus at the subsequent polling. The bus then communicates its priority
request to the traffic controller when detected at the approach of every signal controlled
junction. The decision to implement the requested priority is taken at the local or central level
depending on the type of priority (extension/recall) required.
2.0 Factors need to be considered for the deployment of proposed ITS solution
in West Midlands According to European Commission’s White Paper on Transport (EC, 2011), new forms of
mobility have to be proposed for overcoming reliability, environmental safety and affordability
issues towards sustainable solutions for the transport of people and goods. These solutions will
finally contribute to solving global climate challenges correlating to worldwide requirements and
standards. At the same time, for the road traffic and safety solution, the Commission announced
the ambitious goal to reduce the number of deaths on European roads by a half until 2020 (EC,
2011). Only in the year 2012, about 27.700 people died and 313.000 people were seriously
injured on European roads. The European Commission white paper on transport had almost
covered all the essential factors need to be considered for the deployment of the proposed new
ITS solution. However, the current project focuses on enhancement of Policing/Enforcing Traffic
Regulations System. The main factors that created the need for the development of the proposed
ITS solution in West Midlands were enumerated below:
1. Saturation of the West Midlands road network
2. Improvement on driver and vehicle safety through effective regulation of traffic system.
3. Enhancement of the operation of businesses wihin the West Midlands. and
4. Protection of the environment.
The four (4) driving forces that created the need for deployment of ITS is critically discussed
below with its corresponding steps that the West Midlands (ITA) and potential partners need to
take in order to enable the successful operation of the integrated system.
2.1 Saturation of the road network As bus priority is becoming gradually significant in cities which aid to maintain an effective
public transport service against the threat of congestion. Where road space permits, priority can
be delivered efficiently by not only providing isolated lanes/roadways for buses but in addition,
priority can also be delivered efficiently at traffic signals. According to Priscilla, (2002b) various
European cities indicated an increases of 5% – 16% in bus travels speeds and developments in
punctuality of 5% - 20%. Though, published results of system performance and reliability are
still relatively scarce.
According to UK Department for Transport, (2009), buses are the most leading of public
transport, signifying 64% of total passenger journeys on public transport in England, this
Provisional figures can help the West Midlands (ITA) to consider buses as measure priority
among the public means of transportation. However, bus passenger journeys in England
decreased by 1.8% between 2008 - 2009 and 2009 - 2010 (UK Department for Transport 2010).
11
Polk, (2000) study revealed that throughout the world, innovative system application is being
integrated progressively into bus priority system. With the speedy growth of road traffic
congestion in recent years, an extensive diversity of ITS has been established and adopted
throughout the world (Polk 2000). ITS have been explored for several years in Europe, North
America and Japan, with the view to improve the protection and effectiveness of road transport
and environmental conservation, by applying new technologies to freeway, traffic and transit
systems (Toral et al. 2009). If the general objective of ITS was summarized into a main objective
then this would be enable West Midlands (ITA) to become ‘Smart’, to allow the authority to do
the right thing in the right place at the right time (Lam 2001). ITS retain the capability to deliver
an improved bus service by ensuring that bus operations are fast, consistent and safe; that buses
run on time, their performance monitored and, in case they are required, adjust schedules more
swiftly and accurately. The location of stations and stops should be convenient and passengers
should be informed of the expected times of bus arrivals. All these objectives can be supported
by ITS and bus operations, therefore, can be significantly enhanced.
A wide range of applications for bus-based public transport has been developed in the UK. This
direction can aid to improve the effectiveness of bus operations, creating an additional step
towards providing an actual transport substitute to the private vehicles (Hounsell and Wall 2002).
ITS comprises numerous vital systems, such as Advanced Traffic Management Systems
(ATMS), Area Traffic Control (ATC), Electronic Toll Collection (ETC) and AVL (Lam 2001). A
sequence of projects and field trials, conducted in both the United States and Europe which
delivered good insight into the ITS applications over the last decade (McDonald M., 2006).
According to Luke, (2006), in public transport, applications of the ‘O-Bahn’ system in Australia
(Adelaide) and in Europe (Essen, Leeds, Ipswich and Edinburgh) and Busway Rapid Transit
applications such as in Brisbane, Australia and in Luton, UK are a few examples of ITS
implementations around the world. Recognising the significance of ITS, such as AVL systems,
transport departments internationally are uninterruptedly implementing a diversity of applications
to support public transport. According to D’Acierno et al., 2009 and D’Souza, C., 2010),
amongst these applications, a recent addition is the implementation of a joint use of AVL
technologies, the ‘iBus’ of London. The use of AVL systems deliver great potential in the field of
public transport and may be helpful in addressing important urban transport issues such as the
estimation of road traffic conditions using location AVL data.
2.2: Improvement on driver and vehicle safety The improvement on driver and vehicle safety through Policing/Enforcing Traffic Regulations
System is one of the key factor to consider in achieving integrated transport system in West
Midlands. Driving- and road safety are existing and growing problems with global dimensions.
According to the global status report on road safety conducted by the World Health Organisation
(WHO) in 2013, 1.24 million traffic-connected mortalities occur yearly throughout the world,
presently the foremost cause of death for people aged 15–29 years (WHO, 2013). As a
consequence of the increased need for mobility in developing countries the unceasing growth of
vehicle manufacturing is obvious. According to Mosoti, (2015), the development of the
international vehicle fleet causes an infrastructure backlog, which in turn is accountable for
increased traffic safety risks and accident occurrence. Driver support and safety awareness
programmes have been an area of emphasis to minimise road safety events, and since the WHO
launched “Decade of Action in Road Safety (2011–2020)” programme, a notable development in
road safety has been recorded (Bezerra et al., 2015). In spite of the development of 15% in the
12
annual number of registered vehicles from 2007 to 2013, the yearly mortalities remained stable
in the region of 1.2 million over the same period (Trivedi et al., 2015). Though, a saturation in
the number of mortalities is not good enough and a decrease should be witnessed instead. High
priority is given to traffic safety enhancements by government agencies and major automobile
manufacturers across the world to address this problem, and innovation in driver assistance is
currently in demand.
According to Vaiana et al., (2014), the statistical correlation between driver behaviour and crash
connection is mainly connected to individual variability related with several parameters such as
age, gender and geographic locations. For effective and successful operation of the new proposed
integrated transport system, the West Midlands (ITA) must consider the parameters mentioned.
Interestingly, Driver Behaviour Questionnaire (DBQ) results revealed that violations of traffic
regulation is dropped with age as opposed to errors and the prevalence of violation is higher in
men than in woman (Dodou, 2010). According to (French et al., 1993), traffic accident
involvement is more closely connected to human judgement and decision-making than the mere
inability to control the vehicle, and therefore, the focus of driver behaviour and decision-making
patterns is also a great parameter that the West Midlands (ITA) need to be seriously considered
for effective and successful operation of the integrated transport system. Although results from
the UK Department of Transport’s report for road casualties in Great Britain for 2011 shows that
the decrease of 5% in road accident injuries and fatalities from the preceding year is attributed to
driver awareness campaigns (Al-Sultan et al., 2013), strong indication opposing this claim is
given in (Ker, et al., 2013) in which trial reviews indicated that no impact exists of driver
education on the reduction in traffic crashes or injuries.
Risky driving and to a great degree has been recognized as a main causal behavioural
characteristic that effects road safety for the driver personally, as well as for other drivers
travelling in close proximity to the aggressive driver. A study was carried out by the American
Automobile Association Foundation for Traffic Safety in 2009 found that “as many as 56% of
deadly crashes between 2003 and 2007 involve one or more unsafe driving behaviors typically
associated with aggressive driving” (Johnson et al., 2011 & Zhao et al., 2013).
2.3: Enhancement of the operation of businesses Information and Communication Technology (ICT) is considered a tool that permits safe and
effective operations in freight transportation and that improves visibility, responsiveness and
performance in supply chains (Giannopoulos, 2004; Coronado Mondragon et al., 2012).
According to Armingol et al., (2007); Manzie et al., (2007); and Lumsden & Stefansson, (2007),
Numerous information and communication technologies are used to improve the performance of
transportation networks. Terms such as “intelligent vehicle,” “intelligent highway,” “intelligent
freight,” “intelligent transportation” and “smart transportation” have been introduced by the
industry and academic research to identify the advanced information and communication
technologies that are or will be used in the future for the management of logistics, transportation
and materials handling operations. By using ITSs, logistics operations could be improved by
improving the exchange of information and real-time status updates concerning different
business operations in different modes of transportation (Schumacher et al., 2011). ITS has led to
improvements in the efficiency and safety of railway transportation (Kumar and Kumari, 2012).
13
Maritime transport has recently gained increased attention, especially in connection to the
building and further development of ITSs (Pietrzykowski, 2011).
According to Bekiaris and Nakanishi (2004), the complex aims and effects of ITS concerning
effectiveness, safety and the environment make the evaluation of ITS a complex task. A review
of the literature on this subject shows that it lacks a general overview of the way ITSs
contribute to supporting transportation functions and improving performance dimensions in
light of the types of information used or supported by such systems. ICT is considered a tool for
improving supply chain performance (Sundarakani et al., 2012). Application of ICT can lead to
developments in warehousing activities and customer service (Zeimpekis et al., 2010).
Different types of economic benefits including reduced costs of logistics operations are
achieved through application of ICT to ITS (Chan et al, 2012). One significant benefit of ICT is
improved safety and effectiveness in freight transport operations resulting from developments
in the exchange of information between the actors in supply chains (Giannopoulos, 2004; Vilko
et al., 2012). Moreover, information and communication applications and services in the field
of freight transportation can support the integration of intermodal transportation through supply
chains.
Application of ITS generates better opportunities for improving the performance of all modes
of transport (Pietrzykowski, 2011). According to Crainic et al. (2009) ITS is referred to as “the
latest technologies, infrastructure, and services as well as the operations, planning and control
methods that are used for the transportation of passengers and freight.” Different fields of
technology such as communications, computing hardware, positioning systems,
telecommunications, vehicle technologies, electronics and sensors have become integrated and
shaped the concept of ITS. This support leads to improvements in the performance of
transportation operators. ITS is being used in different areas related to freight transportation,
containing the following: fleet management and control; controlling the position, condition,
placement and identification of freight and vehicles; and city logistics. Such systems can
increase the fluidity of truck traffic, offer seamless border crossings and ensure adequate levels
of control and reporting that lead, in turn, to higher levels of safety and greater efficiency in
transportation systems (Kumar and Kumari, 2012; Coronado Mondragon et al., 2012). They
also have the potential for creating value-adding services for businesses and consumers
(Schumacher et al., 2011).
2.4: Protection of the environment According to Chapman, (2007) the reliance on motorised transport as an everyday function is a
substantive contributor to global climate change. Without significant policy or technological
advances, the likelihood of decoupling transport growth from emissions growth would look
slim given that 95 per cent of transport energy is derived from fossil fuels International Panel
on Climate Change (IPCC, 2007). Table below shows the impact of various ITS schemes on
carbon, fuel and emission release.
Table 1: Indicative evidence on carbon, fuel and emissions impacts of a range of ITS schemes
14
15
Source: Grant-Muller, S. and Usher, M., (2014)
Source: Grant-Muller, S. and Usher, M., (2014)
3.0 Steps that West Midlands (ITA) and potential partners to take for
successful operation of the integrated system In order to have an efficient and functional ITS system, it is absolutely necessary to have a well-
executed ITS maintenance program. A failure to properly maintain an ITS system will result in
poor operation, which affects the Department’s ability to safely and effectively manage their
roadways. In order for the ITS maintenance program to be successful in West Midlands, it will
be necessary to maintain flexibility and a good understanding of priorities for the maintenance
concepts and requirements. The following strategies are strongly recommended.
3.1: Planning According to Bureau of Highway Safety and Traffic Engineering, (2015), after an ITS system is
installed and tested, the Department becomes responsible for the maintenance costs obligatory to
16
keep the system operational so as the integrated transport system function successfully. It is
important that the West Midlands (ITA) provide a suitable budget for preventive maintenance,
response/emergency maintenance, and spare parts. Preventative maintenance costs can escalate
over time as equipment wears out and eventually needs to be replaced. Emergency repair costs
will increase if proper preventative maintenance is not provided. At times, a device may fail
early in its service life. If this is the case, the device may still be covered under a warranty. This
warranty may cover the repair costs. The Integrated Transport Authority (ITA) of ITS Manager
must consider the present warranties when developing an ITS planning.
Table 3 presents sample life expectancies for various ITS device components. This data can be
used to assist West Midlands (ITA) in the development of an estimated ITS maintenance budget.
These lifetimes are typical, and should represent the majority of installations; though, some
installations may have significantly shorter (or longer) lifetimes due to a variety of factors, some
of which may be outside of the West Midlands (ITA) control.
Table 3: Sample Life Expectancies of ITS Device Components (FHWA)
Source: Bureau of Highway Safety and Traffic Engineering, (2015)
Bureau of Highway Safety and Traffic Engineering, (2015) also highlighted that as an ITS
device reaches the end of its service life, it approaches a point of diminishing returns where
maintenance costs begin to exceed the annualized replacement costs. Figure 5 shows a generic
representation of preventative maintenance costs per year versus the cost of replacement,
annualized over the expected device lifespan. This estimation will immensely assist the West
Midlands (ITA) in planning the new integrated transport ITS solution to operate successfully.
17
Source: Bureau of Highway Safety and Traffic Engineering, (2015)
3.2 Scheduling As discussed earlier, the Bureau of Highway Safety and Traffic Engineering, (2015) suggested
that the preventative maintenance should be scheduled every 6 months (unless the manufacturer
suggests more frequently), prior to and after the winter season of each year. However, response
and emergency maintenance can occur at any time, so the West Midlands (ITA) should have
adequate ITS maintenance personnel in place to respond to these situations at any time.
3.3: Training Even the West Midlands (ITA) has enough personal, Bureau of Highway Safety and Traffic
Engineering, (2015) indicated that, it is still helpful to have a capable and well trained ITS staff.
This may be difficult, as there are no common training venues for ITS maintenance; however,
vendor training is typically available and may be included in the installation contract. West
Midlands (ITA) ITS staff should receive any available training in order to allow the West
Midlands (ITA) to supplement the ITS maintenance contract per their capabilities; this may
comprise assigning response/preventative maintenance activities to in-house staff when
available. The West Midlands (ITA) ITS manager should ensure that the ITS staff be trained on
new updates and equipment.
3.4: Documentation According to Bureau of Highway Safety and Traffic Engineering, (2015), a record must be kept
of all maintenance activities performed on ITS devices. This record must be logged. The record
assists the West Midlands (ITA) to respond to any emergency appropriately.
Figure 5 : Preventative Maintenance versus Annualized Maintenance Costs . Source:
18
3.5: Coordination
Coordination of maintenance and repair activities is important for any District with ITS devices
within the West Midlands, and becomes more significant as the number of ITS devices
increases. Maintenance activities must be coordinated among District ITS staff and the
maintenance provider such that it is performed in a timely and cost-effective manner.
According to Bureau of Highway Safety and Traffic Engineering, (2015), ITS maintenance can
be initiated in many ways, such as a call-in from agency staff or the public. Once reported, the
ITS staff member who receives the notification will open a Maintenance Need Report and assign
the response to either the contractor or Department staff. Once the responder has arrived on site
and corrected the issue, the ITS Staff must verify correct operation (where possible). The
responder must submit a completed Field Maintenance Report Form, which will be combined
with the completed Maintenance Need Report (digitally) and submitted to the ITS Maintenance
Repository. Figure 6 shows the maintenance process described above.
Source: Bureau of Highway Safety and Traffic Engineering, (2015)
3.6: Preventative Maintenance According to Bureau of Highway Safety and Traffic Engineering, (2015), “preventative
maintenance is the routine care and service for the purpose of maintaining equipment in
satisfactory operating condition by providing for systematic inspection, detection, and correction
of failures either before they occur or before they develop into major defects”. It also includes
the periodic repair and replacement of components as required to appropriately maintain the
device. This comprises such activities as filter cleaning or changing, cleaning CCTV domes or
DMS face plates, light bulb replacements, faulty surge arrestors, rodent removal, and sealing
conduits. Preventive maintenance is to be accomplished a minimum of twice per year for each
device (unless the manufacturer suggests more), prior to and especially after the winter season of
each year; West Midlands (ITA) ITS manager may request extra preventive maintenance as
required. In order to determine if an ITS device needs more frequent preventive maintenance
visits, the West Midlands (ITA) ITS Manager should consider the age and history of the device,
device type, location of device with respect to roadway, and other possible factors. Once a West
Figure 6 : ITS Maintenance Flow Chart
19
Midlands (ITA) ITS Managers identifies those devices that need maintenance more than twice a
year, they should include the essential maintenance times in a schedule attached to the contract.
See figure 5 for maintenance and troubleshooting.
Source: Bureau of Highway Safety and Traffic Engineering, (2015)
20
References
Al-Sultan, S., Al-Bayatti, A.; Zedan, H., (2013). Context-Aware Driver Behavior Detection
System in Intelligent Transportation Systems. IEEE Trans. Veh. Technol. 62, 4264–4275.
Balaji, P. G., & Srinivasan D., (2011). Type-2 Fuzzy Logic Based Urban Traffic Management.
Engineering Applications of Artificial Intelligence, 24, 12–22.
Bekiaris, E., and Nakanishi, Y., (2004). Economic impacts of intelligent transportation systems:
Innovations and case studies, Research in transportation economics, 8. Elsevier, Oxford.
Bezerra, B.S., Kaiser, I.M., Battistelle, R.A.G., (2015). Road Safety-Implications for Sustainable
Development in Latin America. Sustain. Dev. 2, 1–18.
Bureau of Highway Safety and Traffic Engineering, (2015). Intelligent Transportation Systems
Maintenance Standards. ITS Maintenance Standards[online]. Accessed 11th April 2016.
Available at: http://www.dot.state.pa.us/public/pubsforms/Publications/PUB%20697.pdf
Chan, X., Lau, Y., Ng, J.M.J., (2012). Critical evaluation of ERP implementation on firm
performance: A case study of AT&T. International Journal of Logistics Systems and
Management, Vol. 12 (1) pp. 52-69.
Chapman, L., (2007). Transport and climate change: a review. Journal of Transport Geography
15, 354-367
Chen, W., Li, Z., Yu, M., Chen, Y., (2005). Effects of sensor errors on the performance of map
matching, Journal of Navigation.
Crainic, T.G., Gendreau, M., Potvin, J., (2009). ‘Intelligent freight transportation systems:
Assessment and the contribution of the operations research’, Transportation Research Part C,
Vol.17 (4), pp. 541-557.
Coronado, M., Lalwani, C.S., Coronado M.E.S., Coronado M.C.E., Pawar, K.S., (2012)
Intelligent transport systems in multimodal logistics: A case of role and contribution through
wireless vehicular networks in a sea port location. International Journal of Production
Economics, Vol. 137 (1), pp. 165-175.
D’Acierno, L., Carten, A., and Montella, B., (2009). Estimation of urban traffic conditions using
an Automatic Vehicle Location (AVL) system. European Journal of Operational Research, 196
(2), 719736 [online]. Accessed 13th April, 2016. Available at:
http://www.chinautc.com/usa/upfile/content/20120607104100633.pdf
De Winter, J., Dodou, D., (2010). The Driver Behaviour Questionnaire as a Predictor of
Accidents: A meta-analysis. J. Saf. Res. 41, 463–470.
21
French, D.J., West, R.J., Elander, J., Wilding, J.M., (1993). Decision-making style, driving style,
and self-reported involvement in road traffic accidents. Ergonomics. 36, 627–644.
D’Souza, C., (2010). New developments for bus priority at traffic signals in London using Bus.
Proceedings of road transport information and control conference and the ITS United
Kingdom members conference. London, UK: Dexter House, IET, 25 27[online]. Accessed 13th
April, 2015 Available at: http://www.chinautc.com/usa/upfile/content/20120607104100633.pdf
European Commission, (2011). European Strategy, [Online]. [Accesses 2nd Febuary 2016].
Available:
http://ec.europa.eu/transport/themes/strategies/2011_white_paper_en.ht.
Faghri, A., & Hamad, K., (2002). Application of GPS in Traffic Management Systems, GPS
Solutions, 5(3), 52-60.
Giannopoulos, G.A., (2004). The application of information and communication technologies
in transport, European Journal of Operational Research, Vol. 52 (2), pp. 302-320.
Grant-Muller, S. and Usher, M., (2014). Intelligent Transport Systems: The propensity for
environmental and economic benefits. Technological Forecasting and Social Change, 82,
pp.149-166
Greenfeld, J.S., (2002). Matching GPS observations to locations on a digital map. In
proceedings of the 81st Annual Meeting of the Transportation Research Board. Washington
D.C.
Hernandez, J.Z., Ossowski, S., & Garcya-Serrano A., (2002). Multi=agent Architectures for
Intelligent Traffic Management Systems, Transportation Research Part C, 10, 473–506.
Hounsell, N., and Wall, G., (2002). New intelligent transport systems applications in Europe to
improve bus services. Transportation Research Record: Journal of the Transportation Research
Board, 1791 (1), 8591. http://www.chinautc.com/usa/upfile/content/20120607104100633.pdf
International Panel on Climate Change, (2007). Fourth Assessment Report on Climate Change,
Geneva.
James, R., Date, J. and McBride, C., (2010). Framework for a national intelligent transport
systems architecture March 2010.
Johnson, D.A., Trivedi, M.M., (2011). Driving style recognition using a smartphone as a sensor
platform. Proceedings 14th International IEEE Conference on Intelligent Transportation
Systems (ITSC), Washington, WA, USA; pp. 1609–1615.
22
Ker, K., Roberts, I., Collier, T., Beyer, F., Bunn, F., Frost, C., (2003). Strong evidence that
advancedvand remedial driver education does not reduce road traffic crashes or injuries. Health
doi:10.1002/14651858.CD003734.
Kubrak, D., Macabiau, C., Monnerat, M., Bouchert, M.-L., (2006). Vehicular navigation using a
tight integration of aided-GPS and low-cost MEMS sensors, Proceedings of the Institute of
Navigation Technical Meeting, 149 – 160.
Kumar, N., Kumari, N., (2012). Conceptual architectural design of Indian railway intelligent
transportation systems. Communication Technologies for Vehicles, Vol. 7266, pp. 151162
Lam, W., (2001). Development of intelligent transport systems in Hong Kong ed. Intelligent
transportation Systems. Oakland, CA, USA. 10001005 [online]. Accessed 10th April, 2016.
Available at: http://www.chinautc.com/usa/upfile/content/20120607104100633.pdf
.
Logi, F., & Ritchie, S. G., (2001). Development and Evaluation of a Knowledge-Based System
for Traffic Congestion Management and Control. Transportation Research Part C. 9, 433–459.
Luke, S., (2006). Public transport mode selection: a review of international practice. European
Transport Conference. Strasbourg, France [online]. Accessed 7th April, 2016. Available at:
http://www.chinautc.com/usa/upfile/content/20120607104100633.pdf
McDonald, M., (2006). Intelligent transport systems in Europe: opportunities for future
research. Singapore: World Scientific Publishing. ISBN 978-981-270-082-7 [online]. Accessed
10th April, 2016. Available at:
http://www.chinautc.com/usa/upfile/content/20120607104100633.pdf
Mosoti, R.G., (2015). Effect of motor vehicle congestion on the economic performance of Kenya:
A case of Nairobi city county. 2, 485–502.
Mulay, S. A., Dhekne, C. S., Bapat, R. M., Budukh, T. U., & Gadgil, S. D., (2013). Intelligent
City Traffic Management and Public Transportation System. International Journal of Computer
Science Issues, 10(3), 46-50.
Ossowski, S., Hernandez, J. Z., Belmonte, M. V., Fernandez, A., Garcıa-Serrano, A., Perez-de-
la-Cruz, J., Serrano, J. M., & Triguero, F., (2005). Decision Support for Traffic Management
Based on Organisational and Communicative Multi-Agent Abstractions. Transportation
Research Part C, 13, 272–298.
Pietrzykowski, Z. (2011). Maritime intelligent transport systems. Transport Systems
Telematics, Vol. 104, pp. 455-462.
23
Polk, A.E., (2000). What ITS has to offer municipal governments. 7th world congress on
intelligent transport systems. Paper Number 1051, 69, Turin, Italy [online]. Accessed 3rd April,
2016. Available at: http://www.chinautc.com/usa/upfile/content/20120607104100633.pdf
Priscilla (2002). Evaluation Results, Bus Priority Strategies and Impact Scenarios Development
on a Large Urban Area.
Quddus, M.A., Ochieng, W.Y., Zhao, L., Noland, R.B., (2003). A general map matching
algorithm for transport telematics applications. GPS Solutions, 7(3), 157-167.
Toral, S.L., Vargas, M., and Barrero, F., (2009). Embedded multimedia processors for
roadtraffic parameter extension. Computer, 42 (12), 6168 [online]. Accessed 10th April, 2016.
Available at: http://www.chinautc.com/usa/upfile/content/20120607104100633.pdf
Schumacher, J., Rieder, M., Gschweidl, M., Masser, P. (2011). Intelligent cargo Using
Internet of things concepts to provide high interoperability for logistics systems. Architecting
the internet of things, Springer, pp. 317-347.
Sundarakani, B., Tan, A.W.K., van Over, D., (2012). Enhancing the supply chain management
performance using information technology: International Journal of Logistics Systems and
Management, Vol. 11 No. 3, pp. 306324.
Trivedi, M.; Gandhi, T.; McCall, J., (2007). Looking-in and looking-out of a vehicle: Computer-
vision-based enhanced vehicle safety. IEEE Trans. Intelligent Transport System 8, 108–120.
UK Department for Transport, (2009). Public transport statistics bulletin GB: 2009 edition.
London: Transport Statistics[online]. Accessed 7th April, 2016. Available at:
http://www.chinautc.com/usa/upfile/content/20120607104100633.pdf
UK Department for Transport, (2010). Quarterly bus statistics, Transport Statistics. Great
Britain Q1 2010. London [online]. Accessed 7th April, 2016. Available at:
http://www.chinautc.com/usa/upfile/content/20120607104100633.pdf
Vaiana, R., Iuele, T., Astarita, V., Caruso, M.V., Tassitani, A., Zaffino, C., Giofrè, V.P., (2014).
Driving Behavior and Traffic Safety: An Acceleration-Based Safety Evaluation Procedure for
Smartphones. 8, 88–96.
Vilko, J., Rumpu, A., Koivuniemi, J., (2012). An information-exchange perspective on supply-
chain risk management: Systemic organisational motives and cognitive barriers’, International
Journal of Logistics Systems and Management, Vol. 12 (4), pp. 460482.
World Health Organization Global Status Report on Road Safety (2013). Supporting a Decade
24
of Action[online]. (Available 4th April, 2016). Available at:
http://www.who.int/violence_injury_prevention/road_safety_status/2013/en/
Yokota, T., and Weiland, R.J., (2004). ITS Technical Note. ITS System Architecture for
Developing Countries.
Zeimpekis, V., Minis, I., Pappa, V., (2010). Real-time logistics management of dried figs using
RFID technology: Case study in a Greek cooperative company. International Journal of
Logistics Systems and Management, Vol. 7 (3), pp. 265-285.
Zhao, H., Zhou, H.; Chen, C., Chen, J., (2013). Join driving: A smart phone-based driving
behavior evaluation system. Proceedings IEEE Global Communications Conference, Atlanta,
GA, USA, pp. 48–53.
Zhenlin, W., Peng, Z., & Shulin, A., (2012). Efficiency Evaluation of Beijing Intelligent Traffic
Management System Based on super-DEA. Journal of Transportation Systems Engineering and
Information Technology, 12(3).
top related