installation manual for af-25hb type aluminum frame ... · installation manual for af-25hb type...
Post on 16-Aug-2020
4 Views
Preview:
TRANSCRIPT
1
Thank you for selecting our product. Before starting installation, please read
this manual thoroughly to ensure correct installation.
An improper installation may result in injury.
Please keep this manual at hand for future reference.
■About the product
AF-25HB is a semi-recessed ( the gap between roller and door is minimal )
sliding door system for aluminum frames.
Installation Manual for AF-25HB Type Aluminum Frame Sliding Door
Safety precautions
Installation precautions●This product is a hanging sliding door. Make sure that the structure is strong enough to support the door before installing the tracks.
●Clean the floor of your work area so the aluminum frame of the door is not scratched.
●After unpacking the product, check it for damaged or missing parts.
●Do not disassemble nor modify any parts other than those described in this document.
● If cutting any parts, make sure to remove any burr before installation. Also check the upper track for any left-over burr or
scrap and remove these.
●Please use the tempered glass. It is recommended to use shatterproof film on the glass.
To install the hardware correctly, carefully read the “Safety precautions” and “Installation instructions” in this manual.
This sliding door system should be installed by an experienced person who has correct knowledge. If the system is not
installed correctly, the door will not operate smoothly, and or may cause injury.
It is necessary to manufacture the frame with sufficient strength so it endures the weight of the door and impact shocks upon
opening/closing the door. A frame with poor strength or loose screws might result in improper and slower movement of the
door. In the worst case, the door might drop down and cause injury.
Be sure to follow these instructions. Read and follow these safety precautions toensure safety.
The following icons indicate precautions to prevent incorrect installation and ensure safe use of the product.
Warning
Caution
This icon indicates information that if ignored may lead to incorrect operation that could result in
death or serious injury.
This icon indicates information that if ignored may lead to incorrect operation that could result in
injury.
This icon indicates actions that should not be done (prohibited actions).
This icon indicates actions that must be done.
Also, the icons below are used in addition to the icons above to differentiate between the types of risk and damage.
Parts (for 1 door)
①Hanging roller …… 2 pcsAccessory: Spanner 22 mm
Hexagon socket screw key 3 mm
②Stopper …………… 2 pcsAccessory: Hexagon socket screw key 3 mm
③End cap …………… 2 pcs ④Corner part ……… 2 pcsAccessory: Hexagon socket screw key 3 mm
⑤Guide roller ……… 1 pcAccessory screw: Pan head
tapping screws 4.5 x 16
⑥Screw set
・Hexagon socket head cap screw M6 x 30 …… 8 pcs(for Frame⑨⑩)
・Hexagon socket head cap screw M4 x 30 …… 6 pcs(for Intermediate support⑬)
・Hexagon socket countersunk head screw
M4 x 25 …… 8 pcs(for Corner Part④)
Standard length parts
⑦Standard track2000 mm/3600 mm
⑧Standard double track2000 mm/3600 mm
⑨Vertical frame2500 mm/3000 mm
⑩Horizontal frame2000 mm
⑪Gasketfor 5 mm glass: 2500 mmfor 6 mm glass: 3000 mm
⑫Edge cover2500 mm/3000 mm
Items that need to be prepared at the site
●Screws to install the track⑦⑧ Pan head tapping screws 5 x 40 …………………………as many as needed
●Screws to fix guide roller⑤ Pan head screws 4 x 20 ……………………………………2 pcs (These screws are needed when Floor track ⑮ is used.)
Optional parts
⑬Intermediate support2000 mm
⑭Gasket for Intermediate supportfor 5 mm glass: 2500 mmfor 6 mm glass: 3000 mm
⑮Floor guide track1220 mm,1520 mm,1820 mm,
2440 mm,3000 mm,4000 mm
* No fixing hole is provided for the
guide tracks longer than or equal
to 3000 mm.
2
1 Parts List
3
■Specifications
*Height adjustable range: -1 mm to +4 mm
2 Drawings
40
8080Track hole pitch 240
40
Opening width (RW) = Track length
Door width (TW)
60
Ma
x.
22
00
27
24
15
6.5
19
10
.5
2 1
5 4
10
10
13
1
3
3
3
2
3
12
4
9
912
40
34
*-
1+
45
*-
1+
45
*-
1+
45
(5)
10
.5
85
45
40 40
34
40
34
8.5
ϕ5.5 7 8 7
11
11
14
15
Do
or
he
igh
t (T
H)
= R
H-4
9.5
Op
en
ing
he
igh
t (R
H)
Do
or
he
igh
t (T
H)
= R
H-4
7.5
When door jumb is not provided apply
Two-way soft closer.
Caution
Max.Door width Max.Door height Glass thickness Max.Door weight (1 door)
Without Intermediate support ⑬
900 mm 2200 mm
5 mm or 6 mm 70 kgWith Intermediate support ⑬
1500 mm 2500 mm
Size of door(smaller than below) Required supports
W1600×H20002
W1500×H2200W1300×H2500
3W1200×H2700W1100×H3000 4
*Guide to required numbers of Support(Under 70 kg of door with 5 mm glass)
■Drawing of installed door
Guide roller model : TH (Door height) = RH-49.5
Floor guide track model : TH (Door height) = RH-47.5
Door width TW = (RW-4) + (number of overlaps x 25)
Number of doors
Glass height GH = TH−104−(Number of Intermediate support x 11)
Number of glass panels
Glass width GW = TW−34
Example 1
Example 2
4
3 Dimensions of doors(Cut off after the decimal point for the divided dimensions.)
40 (Door thickness)
TW (Door width)
TH
(D
oor
heig
ht)
RW (Opening width)R
H (
Insid
e h
eig
ht)
TH =2100−49.5
=2050.5
≒2050 mm
TW =
(1800−4)+(1×25) 2*
=910.5
≒910 mm
TH =2100−49.5
=2050.5
≒2050 mm
TW =
(2500−4)+(2×25) 3
=848.666… ≒848 mm
TH =2100−47.5
=2052.5
≒2052 mm
TW =
(1800−4)+(0×25) 2*
=898 mm
TH =2100−47.5
=2052.5
≒2052 mm
Ex: 1 door on single track Size of the door when Opening width 1800 mm and Opening height 2100 mm
Ex: 3 doors on double track Size of each door when Opening width 2500 mm and Opening height 2100 mm
Guide roller model
Guide roller model
Floor guide track model
*Divided with two, since side wall is counted as a door.
Floor guide track model
5
4 Cutting and hole processing of standard length parts
Track (⑦⑧), Floor guide track ⑮ (option)
Length = RW (Opening width)
Horizontal frame ⑩, Intermediate support ⑬ (option)
LH = TW(Door width) - 50(Thickness of Vertical frame x 2)
Vertical frame ⑨
LV = TH (Door height) – 30
・ Cut carefully so the cut edge is square to avoid bias and skewing.・Make sure to remove any burr. Also check the upper track for any left-over burr or scrap and remove these.
RW
40
When the measure from the cut end to the existing hole on the track is 100 mm or more, drill another mounting hole(ϕ5.5) at 40 mm from the cut end.
RW
Drilling ϕ4.6
⑦⑧Rail ⑮Floor guide track(option)
LHM6 threading Min. depth 20 mm
⑩Horizontal frame
2 holes at each end.
LHM4 threading Min. depth 20 mm1 hole at each end.
⑬Intermediate support (option)
LV
⑨Vertical frame
M4 threading, Min.depth 20 mm2 holes at each end.
Caution
Hole B
Hole B
Hole B
TH−302
TH−30
Hole A
Hole A6.5
GH+42.5
24
6.5
GH+42.524
6
Drill holes according to the quantity of Intermediate support.
Hole A only if there is no Intermediate support
Hole A + B for 1 Intermediate support
Hole A + B , B for 2 Intermediate supports
Hole A + B , B , B for 3 Intermediate supports
Hole A
ϕ10.5 hole
ϕ6.2 hole
5 Vertical frame ⑨ processing
Hole B
ϕ8 hole
ϕ4.2 hole
TH : Door height
GH : Grass height
⑤Guide roller
Cross recessed pan headscrew 4 x 20(Not provided)
30
30
30
30
M4 threading
4pcs per bottom Horizontal frame
M4
7
Fix the Guide roller ⑤ to both ends of the Horizontal frame⑩.
6 Horizontal frame ⑩ (bottom) processing(when using Floor guide track ⑮)
Fixing screws
②Stopper
TW (Door width) - 12.5
Floor guide track model
Guide roller model
⑤Guide roller Accessory screw: Cross recessed pan head tapping screw 4.5 x 16
⑦⑧Track
Install the Guide roller with appropriate screws for the mounting location on the Floor track with prepared holes. Recommended screw: Cross recessed pan head tapping screw 5 x40
Provided spanner
①Roller
Hex bolt
Be sure that the mounting surface for
the track is horizontal and flat.
Caution
8
7 Assembling Roller ① , Stopper ②
8 Installing the track and Guide roller ⑤ or Floor guide track ⑮
Check with the direction when insertthe stoppers.
(1) Slightly loosen the Fixing screws with the provided Hex key. (2) Slightly loosen the hex bolt with the spanner provided.
(3) Insert Roller ① and Stopper ② in Track (⑦ or ⑧).
When inserting, temporarily fix Stopper ② with Fixing screws so as
not to protrude from the track.
②Stopper
②Stopper
⑦⑧Track
①Roller
①Roller
Edge
Edge
Fixing plate
Caution
⑩Horizontal frame (bottom)
④Corner part
⑥Hexagon socket countersunk head screw M4 x 25
⑥Hexagon socket head cap screw M6 x 30
⑨Vertical frame
Bottom side
⑪Gasket
⑪Gasket
Glass
(Horizontal length is same as TW (Door width) – 50)
(Vertical length is GH (Glass height))
Bottom side
GW
GH
Glass
⑭Gasket
(Horizontal length is same as TW (Door width) – 50)
⑥Hexagon socket head cap screw M4 x 30
⑬Intermediate support
Bottom side
9
9-1 Assembly of the Vertical frame ⑨ and Horizontal frame (bottom) ⑩
9 Assembling door
9-2
9-3
Insertion of glass <Step 1>
Assembly of Intermediate support ⑬ (option)
・Coat the screws with adhesive for screws.
・Be careful when installing glass to avoid injury.
Caution
■Glass dimensions Horizontal length : TW (Door width) – 34
Vertical length : GH
Glass
Glass
⑭Gasket
(Horizontal length is same as TW (Door width) – 50)
⑪Gasket
(Vertical length is GH (Glass height))
Bottom side
Glass
Glass
⑪Gasket
(Horizontal length is same as TW (Door width) – 50)
⑥Hexagon socket head cap screw M6 x 30
⑩Horizontal frame (top)
Bottom side
Top side
10
9-4 Insertion of glass <Step 2> (option)
9-5 Assembly of Horizontal frame (top) ⑩
Repeat steps 9-3 to 9-4 to assemble doors with more than 2 Intermediate supports.
Glass
Glass
⑪Gasket
(Vertical length is GH (Glass height))
⑥Hexagon socket head cap screw M6 x 30
④Corner part
⑥Hexagon socket countersunk
head screw M4 x 25
⑥Hexagon socket head
cap screw M4 x 30 Bottom side
Top side
Glass
Glass
⑫Edge cover
(Length is LV (Length of Vertical frame⑨))
Bottom side
Top side
Use synthetic rubber
adhesive in a few places
to prevent the Edge
cover ⑫ from shifting.
11
9-6 Assembly of vertical frame ⑨
9-7 Assembling Edge covers ⑫
Bend the Edge cover ⑫
between your fingers and
press it into the side of the
Vertical frame.
Before attaching the Edge covers, make sure the frame is not biased or skewed, and that all bolts are tight.Make sure the parts are firmly assembled and there is no warping or skewing.
Caution
12
(1) Put a support below the door to be hanged. Tilt the door as shown
in the figure, and set the Guide roller ⑤ to the groove of the bottom
horizontal frame ⑩.
(2) Insert the fixing plate of the Roller in the Horizontal frame ⑩ as shown
in the figure below.
(3) Position the Roller at 80 mm from the cut end and fix it with provided
spanner.
B e s u re to h ave s o m e o n e w i t h knowledge and experience assist you.
10 Hanging the door
Guide roller model Floor guide track model
⑤Guide roller
⑮Floor guide track
⑤Guide roller
80
Fixing bolt
①Roller
Provided spanner
Caution
(1) (1)
(3)
(2) (2)
13
11 Adjustment of door height(1) Remove the support under the door.
(2) Turn Vertical adjustment screw of Roller ① with provided spanner and adjust the gap between the door and the floor to 10.5 mm (8.5 mm
for Floor guide track model). The height adjustment range is -4 mm to +1 mm.
(3) Tighten the fixing screw of Roller ① with provided hex key.
(4) Put the End cap ③ on both ends of the door.
(1) Fix the Stopper ② with Fixing screws to the position where the
door touches the Vertical frame.
(2) Adjust the catching force by turning the adjustment screw on
stopper ②.The catching force is set to maximum at the factory.
You may find the gasket coming off from the frame.
In such case, use a Spatel or something to push it in and be careful
not to scratch the glass.
12 Fixing Stopper ② and adjustment
10
.5
Vertical adjustment screw
Fixing screw
③End cap
②Stopper
Fixing screws
Adjustment screw
Spatel
PERIODICALINSPECTION
・Clean inside of track.
・Check upper space and lower space of the door. If necessary, correct the space.
■TROUBLESHOOTINGTrouble Checkpoint Solution
Abnormal noise during
operation
Check if door touches other parts. Provide necessary space between door and adjacent objects.
Check track rollers for aluminum dust. Remove the track and pull out the roller. Then, clean the roller.
Check for loose screws retaining the upper track. Tighten the screw.
Heavy door operation Check if door bottom contacts with floor. Confirm that track fixing screws are not loosened. Adjust door height 6 – 13 mm
between door bottom and floor.
Check if door touches adjacent parts. Correct door position to avoid contact to other objects.
Adjust position of floor guide or stopper.
Door does not move. Check track retaining screws for looseness. Roller touches with screw.
Retighten screws to free the roller.
Door starts to move. Check if the upper track is set horizontally. Using a level gauge, reset upper track horizontally.
142017.01 0786-3
top related