ihc beaver 7525 c cutter suction dredger - alan...
Post on 15-Mar-2020
131 Views
Preview:
TRANSCRIPT
IHC Beaver 7525 C Cutter Suction Dredger
The IHC Beaver 7525C is a mono hull dredger based on the latest and proven technology from the standardisedBeaver range. The dredger features:- use of high efficiency dredge pumps;- two dredgepumps, (one submerged single walled, one on-board double walled) of the same type, using identical wearparts for each of the pumps (impeller, pump casing, wear plates);- diesel direct-driven submerged pump through pivoting gearbox;- engine room and on-board pump at main deck level for easy access;- so called “white iron” highly wear resistant wear parts for the dredge pumps;- separate accommodation unit placed on vibration dampers forimproved comfort for crew.
This type is designated the IHC Beaver 7525 C.75 – diameter of the delivery pipeline is 750mm25 – max. dredging depth is 25 metresC – dredger is equipped with a cutter
PU 2
5 Y-
1
IHC Beaver 7525 C – Cutter Suction Dredger
Principal particularsLength overall, ladder raised 71.50mLength over pontoons 53.90mBreadth 14.00mDepth 3.40mMean draught with full bunkers 2.00mMaximum standard dredging depth 25.00mInternal diameter of suction tube 750mmInternal diameter of discharge pipes 750mmTotal installed power 4,958kW Dredge pumps Submerged pump HRMD 141-30-70 single walledPower of pump drive 1,640kWDredge pump driven via pivoting gearboxInboard pump HRMD 141-30-70 double walledPower of pump drive 1,640kWDredge pump driven through combined pump block/reduction gearboxBall clearance of pumps 299mm
Auxiliary power (cutter, winches, spuds)Cummins KTA50-D developing 1,291 kW (1,755hp) continuous power at 1,800rpm
Electrical installation Board network diesel generator setCummins engine QSM11-D, prime power 265kWHarbour diesel generator setVoltage (50Hz) 3x400V AC Cutter Type 30-CB-ACR-2220-750Power at shaft 750kWDiameter 2,220mmMaximum speed (approx.) 30rev/min Winches (ladder winch / swing winches) line pull, 1st layer 320 / 320kNMax. line speed 20 / 20m/minWire diameter 44mmDrum diameter 960mmSwing wires 200mAnchor weight 2,000kg
Spuds Length 36.50mDiameter 1,200mmWeight 30,000kg
Spud hoisting rams Ram stroke 4.00m Swing width with 35° swing angle at max. dredging depth 58mat min. dredging depth 72m Deck crane Lifting power 50kNOutreach 9.50m
Classification Bureau Veritas Class I, X Hull dredger - no propulsion with notation ‘Coastal Area’ Engine installation after construction
Equipped withSpud carriage installationAnchor boomsSwivel bendVacuum relief valveProduction measuring equipmentAccommodation for 20 persons
Output calculated for:
Soil type Decisive grain size Situ densityA fine sand 100µm 1,900kg/m3
B medium sand 235µm 1,950kg/m3
C coarse sand 440µm 2,000kg/m3
D coarse sand + gravel 1.30mm 2,100kg/m3
E gravel 7.00mm 2,200kg/m3
Pum
p ou
tput
in m
3 of i
n si
tu s
olid
spe
r eff
ecti
ve p
umpi
ng h
our
Pipeline length in meters
0
500
1000
1500
2000
2500
3000
3500
0 2000 4000 6000 8000 10000 12000 14000 16000
AE D C B
IHC Holland B.V.
P.O. Box 204, 3360 AE Sliedrecht Molendijk 94, 3361 EP SliedrechtThe Netherlands
T +31 184 41 15 55F +31 184 41 18 84info@ihcmerwede.comwww.ihcmerwede.com
Internal diameter of discharge pipeline 750mmDredging depth 25mMaximum volumetric concentration of in situsolids of 30%Final elevation at end of pipeline 4m
All
righ
ts re
serv
ed. R
epro
ducti
on in
any
form
or
by a
ny m
eans
is n
ot a
llow
ed,
with
out p
rior
per
mis
sion
in w
ritin
g fr
om IH
C M
erw
ede
B.V.
top related