huawei v1 r3 upgrade guide
Post on 31-Oct-2014
199 Views
Preview:
DESCRIPTION
TRANSCRIPT
V100R300C03SPC200 upgrade Guide
UPGRADE PROCESS
1-Send an Email to NOC before 24 hours.2- Call TX NOC to double Check the old CSH Version and management status.
• Preparation steps before action
1-Access site process. • Site Access
Call TX NOC to collect the print screens for the the following:
NE layout, Ne attribute, SDHservice configuration, link configuration, Ethernet
interface, Ethernet sevice configuration, Clock periority, Communication parameters, IP stack
parameters, OSPF parameters
• Secure backup
UPGRADE STEPSOPEN DC_STANDALONE PROGRAM FOR STARTING THE UPGRADE
FIRSTLY CONFIGURE FTP SERVER CONFIGURATION
FTP SERVER MUST BE IN RUNNING STATUS
FTP SETTING
SYSTEM IP ADDRESS MUST BE THE SAME AS YOUR LAPTOP IP ADDRESS
1. YOU SHOULD PUT THE FILE IN FILE TRANSFER DIRECTORY (IF D: IS CD-ROM CHANGE IT TO E:).2. YOU SHOULD TEST FTP AND THE RESULT SHOULD BE AS HERE
TEST FTP TO CHECK THE CONFIGURATION
BACKUP
BEFORE AFTER
New Task
Upgrade steps
Query then next
Upgrade steps
Upgrade steps
Upgrade steps
Upgrade steps
Upgrade steps
Upgrade steps
Select the target pakage from the specified folder
Upgrade steps
Select the target pakage from the specified folder Select the path from here
Upgrade steps
Upgrade steps
THE PATH MUST BE AS THE FOLLOWING D:/OPTIX RTN950V100R003C03SPC200(5.76.03.45)SOFTWARE_PKG
Upgrade steps
SELECT THE NE.PKG FILE AND THEN PRESS OK
Upgrade steps
AFTER THE NEW VERSION APPEARED PRESS OK
Upgrade steps
Upgrade steps
PRESS OK AND CONTINUE
Upgrade steps
FROM THE DRAG MENU SELECT YOUR TARGET VERSION
Upgrade steps
CONFIRM THE VERSION BY PRESSING “YES”
Upgrade steps
CONFIRM THE PKG FILE AND PRESS OK
Upgrade steps
BE SURE YOU CHECK IN THE PAUSE LIST BEFORE ACTIVATE AND COMMIT AND THEN PRESS NEXT
Upgrade steps
CONFIRM THE PKG BY PRESSING OK
Upgrade steps
PRESS START TASK TO START THE UPGRADE STEPS
Upgrade steps
PRESS YES TO CONFIRM STARTING THE UPGRADE
Upgrade steps
Upgrade steps
Upgrade steps
Upgrade steps
Upgrade steps
PRESS CONTINUE TASK TO START ACTIVATION STEP
Upgrade steps
PRESS YES TO CONFIRM CONTINUE TASK
Upgrade steps
PRESS OK
Upgrade steps
Upgrade steps
Upgrade steps
PRESS CONTINUE TASK TO START COMMIT STEP
Upgrade steps
CONFIRM THE CONTINUE OPERATION BY PRESSING YES
Upgrade steps
PRESS OK
Upgrade steps
Upgrade steps
THE OPERATION SUCCEED AND YOU CAN GET REPORT BY PRESSING “GENERATE REPORT”
Upgrade steps
Choose the correct path and then press “OK”
Upgrade stepsWhen we upgrade from release to other we must upgrade the capacity license
From the ” board software management” menu select “Board software upgrade”
Upgrade steps
Continue by choose “Login NE”
Upgrade steps
Continue by choose “Query Board”
Upgrade steps
Choose “7-CSH” and press “>>”
Upgrade steps
Upgrade steps
Press the upgrade version folder select
Upgrade steps
Set the board software and load type to “license” and then “select software”
Upgrade steps
Select the file *.ini file
Upgrade steps
Confirm the file sected by pressing “OK”
Upgrade steps
Press “yes” to continue
Upgrade steps
Press “start” to start downloading the license
Upgrade steps
Upgrade steps
The license downloaded successfuly
Upgrade stepsThe way to create the license file”*.ini”:
Firstly open the following path:V100R003C03SPC200(5.76.03.45)SoftWare_lcs\OptiX RTN 950 V100R003C03SPC200(5.76.03.45)SoftWare_lcs\NELCS+·¦+¦ñ+¯
Upgrade steps
After choosing the specification needed press create to create the ini file
Upgrade steps
Select the path to save the ini file and then press save
Upgrade steps
After the upgrade the RTN may report some or all the following alarms
CP_TEL_EXHAUST(major alarm): ignore this alarm
User_password needed to be cahanged: close the dc_standalone
Port_mode_mismatch(EM6F): check the mode of the node B and change it to 100M full-duplex
CLK_NO_TRACE_MODE:from NE EXPLORE—select configurationCLOCKClock Subnet Configuration add one source for your clock and then press apply the alarm will clear.
Thank You
top related