hacer un motor (engine) v8 con solidworks
Post on 02-Nov-2014
413 Views
Preview:
TRANSCRIPT
1. Step 1
draw two circles like shown on the front plane
2. Step 2
add two tangent line
3. Step 3
add two more circle
4. Step 4
draw a line and mirror it
5. Step 5
draw a centerline and use trim command
6. Step 6
use fillet command like shown
7. Step 7
go up side and use trim command
8. Step 8
use fillet command again
9. Step 9
extrude the sketch in two directions
10. Step 10
open a sketch on the body and draw a line. make parallel the line with the shown edge
11. Step 11
mirror the line and add this two circle
12. Step 12
Intersect the lines and use trim command
13. Step 13
use trim command and mirror it
14. Step 14
draw two circles and cut the body
15. Step 15
draw two circles more and cut the body again. use ofset feature
16. Step 16
draw a sketch on the body like shown
17. Step 17
extrude it 2mm and use mirror command
18. Step 18
now use fillet command
19. Step 19
your biyel is ready to use
20. Step 20
from Luis :)
1. Step 1
open sketch on the front plane and draw shown sketch
2. Step 2
use trim command
3. Step 3
add a circle
4. Step 4
add two line
5. Step 5
use trim command
6. Step 6
extrude the body in two directions
7. Step 7
draw shown sketch on the body
8. Step 8
extrude it like this
9. Step 9
draw the shown sketch and cut the body
10. Step 10
use fillet command
11. Step 11
your part is ready to use
1. Step 1
open a sketch on the right plane and draw a sketch like shown
2. Step 2
open a sketch on the body. draw a 30mm radiused circle and extrude it 20mm
3. Step 3
use revolve command
4. Step 4
go to other side draw shown sketch and extrude it 20 mm
5. Step 5
open a sketch on same surface and draw shown skecth
6. Step 6
use cut extrude command and tick 'filp side to cut'
7. Step 7
now use mirror command. your crank began to take shape
8. Step 8
use move copy body command. enter volues
9. Step 9
rotate this (4th from right side) body 60degree
10. Step 10
rotate 3th body 120 degree
11. Step 11
rotate sixth body 180 degree
12. Step 12
rotate second body 240 degree
13. Step 13
rotate 5th body 300 degree
14. Step 14
use combine command. your crank is ready for now. we will add oil canal and other parts after
1. Step 1
follow the steps up to here
2. Step 2
click on options--customize
3. Step 3
find this command
4. Step 4
drag and drop the command on the command manager
5. Step 5
click on the command
6. Step 6
use this button
7. Step 7
select the body
8. Step 8
make the copy box ticked and enter 5
9. Step 9
now we will change z coordinate. enter the shown value (95mm)
10. Step 10
confirm that and replicated body is ready.
Aykut Dana 26 days ago
using ' move/copy body' command for rotating
1. Step 1
click on the move copy body command
2. Step 2
click on the body that you want to rotate
3. Step 3
click on rotate option and make sure that copy box have to be unticked
4. Step 4
enter the shown values
5. Step 5
confirm that and rotated body is ready
1. Step 1
open a sketch on the top plane and draw shown sketch
2. Step 2
use revolve command
3. Step 3
open a sketch on top planen again and draw an axis for revolve command
4. Step 4
draw shown sketch
5. Step 5
use revolve command
6. Step 6
thats is all for now
1. Step 1
rollback the feature tree up to mirror1
2. Step 2
use 3D sketch and draw a line. starting point and endpoint have to be center of the circles
3. Step 3
delete the relations
4. Step 4
enter z coordinate -5
5. Step 5
enter z coordinate 20 for this point
6. Step 6
add a plane ( referance geometry>plane then select line and endpoint)
7. Step 7
draw shown circle on this plane
8. Step 8
use cut extrude command
9. Step 9
open a sketch on shown surface and draw a circle
10. Step 10
use cut exturde command
11. Step 11
now open a sketch on the green surface, draw a circle and use cut extrude command
12. Step 12
open a sketch on the right plane and draw shown sketch. then use cut extrude command and cutthe body
13. Step 13
roll forward the feature tree and open a sketch on the right plane
14. Step 14
draw shown sketch then use cut extrude command
15. Step 15
use fillet command
16. Step 16
crank is ready now
1. Step 1
draw shown sketch under the body
2. Step 2
use cut revolve command
3. Step 3
open a sketch on same surface and draw a circle
4. Step 4
use cut extrude command
5. Step 5
open a sketch on the front plane
6. Step 6
draw an axis
7. Step 7
add shown lines
8. Step 8
use cut revolve command
9. Step 9
use mirror command
10. Step 10
now fillet the edges
11. Step 11
oil canalled connecting rod is ready to use
1. Step 1
we will model a piston. try to draw a sketch like in the picture. most importand dimension is pistonradius.
2. Step 2
use cut revolve command
3. Step 3
open a sketch on front plane and draw a rectangle
4. Step 4
use cut extrude command and cut the body
5. Step 5
open a sketch on this surface
6. Step 6
draw this sketch with using mirror command
7. Step 7
extrude it. then open a sketch on this surface
8. Step 8
use convert entities command and select this surface
9. Step 9
draw the shown sketch
10. Step 10
use trim command
11. Step 11
extrude and mirror it
12. Step 12
open a sketch on blue surface and draw a 11mm circle center of it
13. Step 13
cut the body
14. Step 14
now you should use fillet command.
15. Step 15
use dome command
16. Step 16
piston is ready for now. follow next tutorial
1. Step 1
draw shown sketch on the front plane
2. Step 2
use cut extrude command
3. Step 3
use section view button
4. Step 4
open a sketch on the front plane and draw shown sketch
5. Step 5
add an axis
6. Step 6
use cut revolve command
7. Step 7
your piston is ready to use.
1. Step 1
open a sketch on the front plane and draw two circles
2. Step 2
extrude the sketch in two ways 34,5mm
3. Step 3
use fillet command
4. Step 4
your pin is ready to use
5. Step 5
now open connecting rod part 2 and draw shown sketch
6. Step 6
use cut revolve command
7. Step 7
your oil canaled connecting rod part is ready to use
1. Step 1
open a sketch on right plane and draw a axis for new plane
2. Step 2
create a plane that have to be 35 degree between new plane and right plane. then open a sketchand draw 4 circles
3. Step 3
draw two circles like shown
4. Step 4
use mirror command two times
5. Step 5
finally make your sketch like this
6. Step 6
use extrude commad
7. Step 7
open a sketc under the body and draw two circles. smaller circles radius is 50mm. other one haveto be bigger then body. then use cut extrude command and enter volues
8. Step 8
open a sketch on cutted surface and draw circles like this
9. Step 9
make your sketch like this
10. Step 10
use extrude command
11. Step 11
use linear pattern command. you must to decide that how many cylinder you want. I prefered tomake 12 cylinder.
12. Step 12
now we will cut the surplus portions. please check the photo and try to draw a sketch on the bodylike this. you should use linear pattern command
13. Step 13
use the command and cut the body 70mm. That's all for now. please follow the tutorial step bystep. if you have a problem with the tutorials please let me know
1. Step 1
open a sketch on the right plane
2. Step 2
draw a centerline
3. Step 3
use features--referance geometry--plane command
4. Step 4
select the line and the right plane
5. Step 5
then enter shown value
6. Step 6
open a sketch on the plane that we created just now
7. Step 7
draw a circle
8. Step 8
draw two more circles
9. Step 9
draw one more circle
10. Step 10
draw a circle like shown
11. Step 11
draw a circle again. it should be concentric with the circle that we created just now
12. Step 12
now we will use trim command. sketch--trim command
13. Step 13
before trim this lines
14. Step 14
after trim these lines
15. Step 15
finally trim these lines and confirm the command
16. Step 16
draw a centerline. we will use it for mirror command
17. Step 17
now we will use mirror command. use sketch--mirror commad. then select shown sections
18. Step 18
click on this box
19. Step 19
select the centerline
20. Step 20
confirm that. now we will use trim command again
21. Step 21
trim these lines
22. Step 22
confirm that. then draw a centerline again. it will uses for mirror
23. Step 23
open mirror command and select shown sections
24. Step 24
click on shown box, select the mirror axis and confirm that
25. Step 25
use trim command and make your sketch like shown
26. Step 26
now we will use fillet command
27. Step 27
enter shown radius parameter by 15mm, then only click on shown points
28. Step 28
confirm that and your sketch should be like this
29. Step 29
make same thing for the other points
30. Step 30
sketch finished. please check it
31. Step 31
now we will extrude this sketch. open extrude command
1. Step 1
use extrude command
2. Step 2
select the shown area
3. Step 3
then select this area
4. Step 4
change the direction with using this button
5. Step 5
use offset option
6. Step 6
change the offset direction and enter shown value
7. Step 7
finally enter this value and confirm that
8. Step 8
body is ready
9. Step 9
open a sketch on this surface
10. Step 10
draw two concentric circles
11. Step 11
use cut extrude command like shown.
12. Step 12
your body should be like this
13. Step 13
now open a sketch on this surface
14. Step 14
draw a concentric circle
15. Step 15
normal to selected plane
16. Step 16
draw a big circle
17. Step 17
now we will use this circle option. please click on it
18. Step 18
firstly click on this circle
19. Step 19
secondly clik on this circle and complate your perimeter circle. If you can not, please try again.you will see it is not too hard
20. Step 20
enter the shown dimension
21. Step 21
draw a centerline
22. Step 22
use trim command
23. Step 23
use mirror command and select shown sketch
24. Step 24
then select the centerline and confirm that
25. Step 25
use trim command again
26. Step 26
draw a centerline .
27. Step 27
use mirror command and select the sketch
28. Step 28
select the centerline that we created just now
29. Step 29
draw one more centerline
30. Step 30
use mirror command again. select the shown lines
31. Step 31
select the shown centerline and confirm that
32. Step 32
now use convert entities command and select the shown edges
33. Step 33
select the other hole edges and confirm that. sketch finished.
1. Step 1
open a sketch on front plane and draw water canal profile
2. Step 2
extrude it
3. Step 3
create a plane bottom of body and use mirror command for to mirror water canal
4. Step 4
after open a sketch on this surface
5. Step 5
draw a sketch like this and use cut extrude command
6. Step 6
go to left side, open a sketch and draw a sketch like this
7. Step 7
extrude it. please attention that to make direction 'up to surface'. select the outer surface of thecylinder
8. Step 8
open a sketch on same surface and draw semi-circular profile. it have to be closed profile
9. Step 9
create the plane 3 ( it is at the center of water canal) then draw the path.( we will use sweepcommand)
10. Step 10
use sweep command. then mirror it
11. Step 11
create a inlet part like this
12. Step 12
close the back side with your method
13. Step 13
mirror all things and your water cooled 12 cylinders are ready
1. Step 1
open a sketch under the body and draw this sketch.( you can use convert entities command forcircles)
2. Step 2
extrude the sketch 10 mm
3. Step 3
go to front plane and draw this profile
4. Step 4
mirror all bodies with using right plane
5. Step 5
extrude the profile at each directions. after, use body-move-copy comman to translate body 15mm on Z coordinate.
6. Step 6
open a sketch under the body and draw this sketch
7. Step 7
extrude it up to top plane
8. Step 8
open a sketch on the right plane. use convert entities command.
9. Step 9
extrude the last sketch in two directions. direction 1 is up to body and direction 2up to purplesurface
10. Step 10
crop the body
11. Step 11
go to under of the body and draw this sketch
12. Step 12
use linear pattern command (95 mm gab) then extrude the sketch up to pink surface
13. Step 13
make same things for other side
14. Step 14
crop this parts
15. Step 15
open a sketch front side and draw a 30mm radiused circle. then use cut extrude command
16. Step 16
open a sketch on the cylinders. draw circles like this
17. Step 17
use cut extrude command. enter volues
18. Step 18
please follow next tutorial
1. Step 1
open a sketch on the front of the body and draw a circle
2. Step 2
extrude it at two directions
3. Step 3
open a canal
4. Step 4
open a sketch under the body and draw circles like this
5. Step 5
use cut extrude command
6. Step 6
open a sketch same surface again. draw circles like this. we will use cut revolve command, so don'forget the axis
7. Step 7
use cut revolve command. select the circles and axis
8. Step 8
now oil canals are ready
1. Step 1
open a sketch and draw this sketch
2. Step 2
extrude the sketch 35 mm. then draw this two circles and cut the body
3. Step 3
use fillet command
4. Step 4
this part is ready to use. now we will make another connector
5. Step 5
draw a circle and a centerline on the blue surface
6. Step 6
use cut revolve command
7. Step 7
your part is ready to use
1. Step 1
draw shown sketch
2. Step 2
extrude the sketch 60mm
3. Step 3
open a sketch on the body and draw shown circles
4. Step 4
cut the body
5. Step 5
draw a 30mm radiused circle like this and use cut extrude command
6. Step 6
open a sketch on the blue surface
7. Step 7
draw shown two circles and centerline
8. Step 8
use cut revolve command. that is all for now
1. Step 1
draw shown sketc on the top plane
2. Step 2
use extrude command
3. Step 3
draw two rectangle on the body
4. Step 4
exturde it 120mm
5. Step 5
use cut extrude command
6. Step 6
draw shown rectangle on the body
7. Step 7
open a sketch on the blue surface
8. Step 8
draw shown sketch
9. Step 9
use mirror command and extrude the sketch up to green surface
1. Step 1
draw shown sketch on the blue surface
2. Step 2
use cut extrude command .
3. Step 3
use extrude command. click on 'from surfacde-face-plane' option and select he green surface. thenclick on direction 1 'up to surface' and select the pink surface
4. Step 4
draw shown sketch on the blue surface..
5. Step 5
extrude the sketch up to pink surface
6. Step 6
draw shown sketch front of the body
7. Step 7
make same things again
8. Step 8
draw a rectangle on the blue surface
9. Step 9
use cut extrude command.
please follow next tutorial
1. Step 1
open a sketch on this surface
2. Step 2
use cut extrude command
3. Step 3
draw shown on the blue surface
4. Step 4
please examine the shown sketch. draw the same. then exit from sketch
5. Step 5
click on the sketch from feature tree and click on show button
6. Step 6
extrude this rectangles up to pink surface
7. Step 7
open a sketch on this surface..
8. Step 8
use section view command
9. Step 9
draw shown sketch
10. Step 10
add a circle
11. Step 11
use trim command
12. Step 12
extrude the sketch 4mm. make untick 'merge result' option
1. Step 1
use move-copy- body command
2. Step 2
go on like this
3. Step 3
use same command again
4. Step 4
open a sketch on blue surface
5. Step 5
use section view command..
6. Step 6
use convert entities command
7. Step 7
use trim command and trim this lines
8. Step 8
add a 70mm radiused circle
9. Step 9
trim the sketch
10. Step 10
extrude it
11. Step 11
use move-copy body command
12. Step 12
go on like this
13. Step 13
copy last part
1. Step 1
use fillet command
2. Step 2
after, make fillet this edges
3. Step 3
draw a circle
4. Step 4
use linear pattern command
5. Step 5
cut the body
6. Step 6
use mirror command
7. Step 7
open a sketc on blue surface and draw a circle like this
8. Step 8
use linear pattern command..
9. Step 9
draw a centerline and use mirror command
10. Step 10
use cut extrude command
1. Step 1
open new assembly document
2. Step 2
click on browse button and find your crankcase
3. Step 3
click on insert new compaoent button and find your crankshaft
4. Step 4
use matte command and click on blue surface
5. Step 5
after, click on this surface. they will be contentric
6. Step 6
confirm that
7. Step 7
click on blue surface for add matte
8. Step 8
click on shown surface and select distance option. enter 2,5mm volues
1. Step 1
insert a piston and a connecting rod
2. Step 2
make contentric this surfaces
3. Step 3
select right plane of the piston and click on matte command
4. Step 4
find connecting rods front plane from feature tree
5. Step 5
make them coincident
6. Step 6
make this survaces concentric
7. Step 7
confirm that
8. Step 8
use matte command again and select this surfaces
9. Step 9
click on ok
10. Step 10
add 11 more piston and connecting rod . unfortunately you have to make same things for all
1. Step 1
open connecting rod. use insert-part command and insert the connecting rod part 2
2. Step 2
click on this button
3. Step 3
click on shown surfaces and click on add button
4. Step 4
now select this surfaces and click on add button
5. Step 5
combine the parts
1. Step 1
open the piston. use insert-part command and choose the pin
2. Step 2
click on shown surfaces for to add matte. make them concentric
3. Step 3
then click on this surfaces and define the distance
4. Step 4
piston-pin is ready
1. Step 1
open your saved assembly. we changed piston and connecting rod. if solidwork ask you for rebuil,please confirm that. now insert this part
2. Step 2
firstly make coincident this surfaces
3. Step 3
use matte command and click on this surfaces.
4. Step 4
make this surfaces coincident. confirm that
5. Step 5
insert this part
6. Step 6
make this surfaces coincident.
7. Step 7
and this surfaces..
8. Step 8
finally make this surfaces conctric. now add 5 more new part and make same things for them
9. Step 9
your engine must be look like this
1. Step 1
insert the carter
2. Step 2
make this surfaces coincident
3. Step 3
do it for this surfaces again
4. Step 4
finally do it for this surfaces. click on ok. we finished the V12. of course I will generate new tutorials for new parts. please follow
https://d2t1xqejof9utc.cloudfront.net/pictures/files/5961/large.JPG?1330028346[21/05/2012 18:30:21]
https://d2t1xqejof9utc.cloudfront.net/pictures/files/5965/large.JPG?1330028351[21/05/2012 19:04:16]
https://d2t1xqejof9utc.cloudfront.net/pictures/files/5966/large.JPG?1330028352[21/05/2012 19:09:23]
https://d2t1xqejof9utc.cloudfront.net/pictures/files/5967/large.JPG?1330028354[21/05/2012 20:09:25]
https://d2t1xqejof9utc.cloudfront.net/pictures/files/6380/large.JPG?1330113499[21/05/2012 20:10:54]
https://d2t1xqejof9utc.cloudfront.net/pictures/files/6388/large.JPG?1330113509[21/05/2012 20:30:31]
https://d2t1xqejof9utc.cloudfront.net/pictures/files/6389/large.JPG?1330113510[21/05/2012 20:30:42]
https://d2t1xqejof9utc.cloudfront.net/pictures/files/6391/large.JPG?1330115707[21/05/2012 20:36:01]
https://d2t1xqejof9utc.cloudfront.net/pictures/files/6400/large.JPG?1330115718[22/05/2012 2:22:11]
https://d2t1xqejof9utc.cloudfront.net/pictures/files/6401/large.JPG?1330115719[22/05/2012 2:22:21]
https://d2t1xqejof9utc.cloudfront.net/pictures/files/6404/large.JPG?1330115723[22/05/2012 11:17:35]
https://d2t1xqejof9utc.cloudfront.net/pictures/files/6405/large.JPG?1330115724[22/05/2012 11:19:33]
https://d2t1xqejof9utc.cloudfront.net/pictures/files/6407/large.JPG?1330116219[22/05/2012 11:30:42]
https://d2t1xqejof9utc.cloudfront.net/pictures/files/6408/large.JPG?1330116220[22/05/2012 11:35:25]
https://d2t1xqejof9utc.cloudfront.net/pictures/files/6410/large.JPG?1330116222[22/05/2012 11:38:17]
https://d2t1xqejof9utc.cloudfront.net/pictures/files/6415/large.JPG?1330119536[22/05/2012 12:11:13]
https://d2t1xqejof9utc.cloudfront.net/pictures/files/6416/large.JPG?1330119537[22/05/2012 12:11:21]
https://d2t1xqejof9utc.cloudfront.net/pictures/files/6418/large.JPG?1330119539[22/05/2012 12:14:17]
https://d2t1xqejof9utc.cloudfront.net/pictures/files/6422/large.JPG?1330120124[22/05/2012 12:32:25]
https://d2t1xqejof9utc.cloudfront.net/pictures/files/6423/large.JPG?1330120125[22/05/2012 12:34:23]
https://d2t1xqejof9utc.cloudfront.net/pictures/files/6426/large.JPG?1330120129[22/05/2012 12:47:38]
https://d2t1xqejof9utc.cloudfront.net/pictures/files/6427/large.JPG?1330120130[22/05/2012 13:09:50]
https://d2t1xqejof9utc.cloudfront.net/pictures/files/6429/large.JPG?1330120133[22/05/2012 13:15:37]
https://d2t1xqejof9utc.cloudfront.net/pictures/files/12282/large.JPG?1336351424[22/05/2012 13:38:51]
https://d2t1xqejof9utc.cloudfront.net/pictures/files/12223/large.JPG?1336327605[22/05/2012 14:00:24]
https://d2t1xqejof9utc.cloudfront.net/pictures/files/6432/large.JPG?1330120136[22/05/2012 14:44:40]
https://d2t1xqejof9utc.cloudfront.net/pictures/files/6433/large.JPG?1330120137[22/05/2012 17:44:06]
https://d2t1xqejof9utc.cloudfront.net/pictures/files/12266/large.JPG?1336351105[22/05/2012 17:59:55]
https://d2t1xqejof9utc.cloudfront.net/pictures/files/12267/large.jpg?1336351106[22/05/2012 18:00:01]
https://d2t1xqejof9utc.cloudfront.net/pictures/files/12268/large.JPG?1336351107[22/05/2012 18:00:10]
https://d2t1xqejof9utc.cloudfront.net/pictures/files/12269/large.JPG?1336351108[22/05/2012 18:00:24]
https://d2t1xqejof9utc.cloudfront.net/pictures/files/6434/large.JPG?1330120902[22/05/2012 18:01:38]
https://d2t1xqejof9utc.cloudfront.net/pictures/files/6435/large.JPG?1330120905[22/05/2012 18:01:44]
https://d2t1xqejof9utc.cloudfront.net/pictures/files/6436/large.JPG?1330120907[22/05/2012 18:01:57]
https://d2t1xqejof9utc.cloudfront.net/pictures/files/6437/large.JPG?1330120908[22/05/2012 18:03:17]
https://d2t1xqejof9utc.cloudfront.net/pictures/files/6438/large.JPG?1330120910[22/05/2012 18:03:24]
https://d2t1xqejof9utc.cloudfront.net/pictures/files/6439/large.JPG?1330120912[22/05/2012 18:04:31]
https://d2t1xqejof9utc.cloudfront.net/pictures/files/6440/large.JPG?1330120913[22/05/2012 19:14:10]
https://d2t1xqejof9utc.cloudfront.net/pictures/files/6441/large.JPG?1330120915[22/05/2012 19:14:18]
https://d2t1xqejof9utc.cloudfront.net/pictures/files/6444/large.JPG?1330120920[22/05/2012 22:00:18]
https://d2t1xqejof9utc.cloudfront.net/pictures/files/6445/large.JPG?1330120922[23/05/2012 20:40:13]
top related