guitar signal transmitter
Post on 31-Dec-2015
49 Views
Preview:
DESCRIPTION
TRANSCRIPT
Project by Project by
Santiago Yeomans, Chad Cummins, Santiago Yeomans, Chad Cummins, Gboyega AdeolaGboyega Adeola
Guitar Signal Guitar Signal TransmitterTransmitter
IntroductionIntroduction
• Electric guitar output will connect to FM transmitter
• Transmitted audio will be received at receiver and connected to guitar amplifier
• ¼ “ audio plugs used for connections– output of guitar to transmitter– output of receiver to amp
Frequency Modulation vs. Phase Modulation
FM PM
Fair S/N ratio Best S/N ratio
Variable modulation index
Constant modulation index
Easier implementation
Phase lock loop to demodulate signal
VCO can produce high index freq. modulation
Multipliers needed to produce high index PM
Cost efficient Expensive
Flow Diagram Flow Diagram
Reactance Modulator
Carrier Oscillator
Buffer AmplifierFrequency Multipliers
Driver Amplifier
Power outputamplifier
Reactance Modulator: The nature of FM is that when the baseband signal is zero, the carrier is at its “carrier” frequency, when it peaks the carrier deviation is at a maximum and when it troughs the deviation is at its minimum. This deviation is simply a quickening or slowing down of frequency around the carrier frequency by an amount proportional to the baseband signal. In order to convey this characteristic of FM on the carrier wave, the capacitance must be varied.
Buffer Amplifier: The buffer amplifier acts as a high input impedance with a low gain and low output impedance associated with it. The high input impedance prevents loading effects from the oscillator section.
Frequency Multipliers: To avoid frequency drifts of the LC tank while modulating the carrier by the baseband with a high modulation index, modulation can take place at lower frequencies with a higher Q factor of the oscillator.
Power Output Section- Develops the final carrier power to be transmitted. Also included here is an impedance matching network, in which the output impedance is the same as that on the load (antenna)
Block DiagramBlock Diagram
InOut
Three StagesThree Stages• Signal Source (Guitar, CD player)
– CD Audio Output: >1.5 V– Guitar Signal Output: 150mv– Output Impedance:
• Transmitter– Colpitts Oscillator ---– Circuit Self-Amplification
• Receiver– Hartley Oscillator ---– Audio amplifier
Oscillator
Resonant Circuits.Resonant frequency is that at which the impedance of capacitor & inductor is the same; it represents the oscillator carrier frequency in Hertz. The parallel resonant circuit we used, known as an LC tank, takes the advantage of the resonant frequency and allows the impedance to be at a maximum & the current at a minimum at Fc.
Q : ratio of maximum energy stored to the amount lost per ac cycle. It determines the 3dB bandwidth of resonant circuits.
Since we didn’t have a resistor in the LC tank, the inherent properties of inductor & capacitor at high frequencies had to be taken into account.
Essential Circuit ElementsEssential Circuit Elements• Transistors:
– Transmitter: 2 (2N3904)– Receiver: BF256, 2N3904
• Inductors– Copper Coils
• 5 turns• 16 turns
TransmitterTransmitter
ReceiverReceiver
LPF 682 HzLPF 682 Hz
1 kHz1 kHz
Chebyshev Filters6-Band Equalization Stage6-Band Equalization Stage
2 kHz2 kHz
4 kHz4 kHz
8 kHz8 kHz
10.9 kHz10.9 kHz
Pspice SimulationPspice Simulation
Output of receiver connected to guitar Output of receiver connected to guitar amplifieramplifier
Project AchievementsProject Achievements• Achieved both FM RF Transmission
and reception– Carrier frequency of 100 MHz
• Audio received and sent to guitar amplifier
• Audio from cd player worked well• Temporarily had guitar audio
transmitting and receiving• Circuits were low cost to build
PerformancePerformance• Quality of Audio
– Clear at times, some noise occasionally
• Transmission– Better transmission was achieved with a
source device having a larger input impedance.
Project ChallengesProject Challenges• Setup both transmitter and receiver for same carrier frequency (100MHz)
– Variable Capacitor range was unknown, not sure about the pins(Variable cap taken from $5 handheld radio bought from Wal-Mart)
Challenges continuedChallenges continued• Working with the LM741 Op Amp• Working with a breadboard• Parasitic Capacitances• Unable to Effectively Simulate• Inductors• Parasitic Capacitances inherent in high
frequency engineering
OversightsOversights
• Impedance Mismatching– Between Amplifier and Receiver
• Under-estimated difficulty of amplifying guitar audio before transmission
TimelineTimeline
Factors for obtaining better S/N
Resistive properties in LC tankA) Skin effect - at high frequencies, there is less cross sectional area for carriers to
move, so the resistance increase; when the magnetic field at the centre of the wire increases and local inductive reactance takes over, that is, stray capacitances begin to build up between adjacent turns.
B) Dielectric permittivity
Temperature Stability of the oscillatorComponents in oscillator have non-zero temperature coefficients. To find thechange in frequency for a given temperature change, simply multiply the coefficient by the temperature change & the centre frequency.Major source of frequency instability: Capacitor & Transistor (junction capacitance)
More compact circuitry
Wrapping the circuit with aluminum foil to electromagnetically shield the RF stage. Unwanted electromagentic radiation had to be stopped from destructively interferingWith the carrier modulation.
Future ImprovementsFuture Improvements
• Replace the common 2N3904 transistor with a BC549 which would perform better with high frequency
• Use a ground plane for better performance of sensitive circuits
• Solder all connections
top related