frontier print frontier print quality nproblems
Post on 28-Feb-2018
254 Views
Preview:
TRANSCRIPT
-
7/25/2019 Frontier Print Frontier Print Quality nProblems
1/22
Frontier Print Quality Problems
Page 2. Magenta dots Replace GFM20Page 3. Banding / missing part of the print Replace sub scan unit
Page 4. Discolored prints / Solarization Replace FMB and FMC
Page 5. Magenta blotches - Replace FMB
Page 6. Streaking - Clean Polarizing filter
Page 7. Lines in the prints, 8 lines per cm. Inadequate ground connection.
Page 8 Noise from fluorescent lights(Firewire)
Page 9 Magenta Lines FMB20 not seated in connector.
Page 10 Green, Magenta halo at dark edges. MFC10Y, Slides
Page 11 White Shading / Eclipsing or Lamp is out
Page 12. FR010 Auto Film Carrier Dust-Induced Streaked Unevenness
countermeasuresPage 14. FR 013 Y/R (Yellow/Red) Cast Fog on Prints
Page 15. FR 026 Cyan Belt-like Image Print in the Main Scanning Direction
Page 17. ED 026 Image Abnormality ( trailing end white background/streaks )
countermeasure
Page 18. FR 038 RP Tone Printing Setup
Page 20. FR 055 Image Abnormality (Face Shadow) Countermeasures
Page 21. FR 057 Developer Rack Section (P1) Non-uniform Processing
Countermeasures
Distributed by: minilablaser.com
http://minilablaser.com/http://minilablaser.com/ -
7/25/2019 Frontier Print Frontier Print Quality nProblems
2/22
2
Magenta dots Replace GFM20From: Bill Edwards To: "Bach Lequang (Fuji)" ,...Date: 2/24/00 3:21amSubject: Frontier Bad GFM20 Samples
Specialist Staff,Attached is a sample from a Frontier 370 with a bad GFM20 PCB. Noerrors were generated by this problem. This unit has been in operationfor a couple of months on a low volume basis. The problem is a highlypixelated image with magenta dots patterning in gradated areas mid value
between highlight and shadow. Also the monitor image represented thesedots as green instead of magenta obviously in lower resolution. Theresulting index print was fine. Dropping to monotone or disablinghypertone had no effect on the problem. Once the GFM20 PCB was replacedthe problem was gone. Just an addition to the image processing odditiescollection.Bill.Those of you getting these via dial-up sorry for the long download.
Distributed by: minilablaser.com
http://minilablaser.com/http://minilablaser.com/ -
7/25/2019 Frontier Print Frontier Print Quality nProblems
3/22
3
Banding / missing part of the print Replace sub scan unit
Problem Description: ( be as conciseas possible )The printer would jam and slip whilepreforming the sub scan because theroller towards the solutions on thesubscan unit would intermeitantly stop.This was because the belt part#323d889734A was riding against thewall of the subscan unit..
Solution:
Replace the unit or adjust belt tracking
with the adjustment screws
Comments: ( provide as much detail aspossible, ie. data, conditions, sequence ofevents )It would apear that this is something thatwas done at the factory and not as aresult of anything done by the owner ofthe Printer.
Distributed by: minilablaser.com
http://minilablaser.com/http://minilablaser.com/ -
7/25/2019 Frontier Print Frontier Print Quality nProblems
4/22
4
Discolored prints / Solarization Replace FMB and FMC
Installation Mulfunction AnalysisSite Hise StudioB#_SP1500 2895104 Software Ver. 1.8-0E-112B#_LP1500SC 2915104 Software Ver. 1.8-0E-061Subject_Phenomenon_*Discolored prints from all production through the SP. Any paper tests came out normal.Production prints had a yellow-orange soloarization to the highlights of the prints and/or samecolor banding on one side of the print. The problem was not consistent in the area of the printthat it occurred or the amount of the print that was effected. This problem occurred beforeupgrading machine to Ver. 1.8 and afterward. Machine was originally on Ver 1.7.*Light source stabilization for the multifunction carrier is confusing for the customer. Whenyou insert the carrier it asks you to click skip to perform the test or yes to continue. Thecustomer at my install found this to be confusing unless you read the passage carefully._Result_The correction came by changing both the FMC and FMB boards. Before replacement I triedto clean the contacts of the existing FMB board with no change. I was unable to replace justthe FMB because it was hard wired to the FMC board with blue trace wire. This part musthave been from the early stock of back-up parts Tokyo supplied to us. After installation theproblem was gone and all production was okay. Both boards were returned to parts thefollowing day. No sample prints are enclosed because the customer threw the prints set asidefor me away.
Distributed by: minilablaser.com
http://minilablaser.com/http://minilablaser.com/ -
7/25/2019 Frontier Print Frontier Print Quality nProblems
5/22
5
Magenta blotches - Replace FMB
Streaking and magenta blotches. Resolved by replacing the FMB circuit board.
Distributed by: minilablaser.com
http://minilablaser.com/http://minilablaser.com/ -
7/25/2019 Frontier Print Frontier Print Quality nProblems
6/22
6
Streaking
- Only showed on underexposed negatives.- Caused by dust on Polarizing filter over the lens. --- cleaned to resolve the problem.
* Note the banding across the picture.
Distributed by: minilablaser.com
http://minilablaser.com/http://minilablaser.com/ -
7/25/2019 Frontier Print Frontier Print Quality nProblems
7/22
7
Evenly spaced lines in the print, subscan direction.
Problem:Lines(8 lines per cm) in the subscan direction. The lines can be seen
by producing a test print on the LP from the Special Print menu.
Solution:Check the ground wires from the machines to their outlets and that the
ground is common to both the SP and LP.
Distributed by: minilablaser.com
http://minilablaser.com/http://minilablaser.com/ -
7/25/2019 Frontier Print Frontier Print Quality nProblems
8/22
8
Noise from fluorescent lights(Firewire)
Problem:3 color hair like or EKG lines in prints.
Solution:The firewire was routed up into the ceiling and over a fluorescent light
fixture.
Rerouting the firewire between the fluorescent light fixtures.
Distributed by: minilablaser.com
http://minilablaser.com/http://minilablaser.com/ -
7/25/2019 Frontier Print Frontier Print Quality nProblems
9/22
9
Magenta Lines FMB20 .
The FMB20 PCB had become loose in its connector from vibration of loading paper
magazines roughly.
Reseat the FMB20 PCBs.
Distributed by: minilablaser.com
http://minilablaser.com/http://minilablaser.com/ -
7/25/2019 Frontier Print Frontier Print Quality nProblems
10/22
10
Green, Magenta halo edges. MFC10Y, Slides
Vibration during fine scan. Mounted slides.
The shafts on the MFC10Y were cleaned and lubed..
Check the slide in its mount. The slide samples received the slides were loose in the
mount.
Distributed by: minilablaser.com
http://minilablaser.com/http://minilablaser.com/ -
7/25/2019 Frontier Print Frontier Print Quality nProblems
11/22
11
White Shading / Eclipsing or Lamp is out
Prints are light going to dark
Check PU351 compressor and air filter. Menu 43A(Scanner I/O) check D351 Flow
volume sensor. 4.50 5V OK. Replace D351 senos if the reading is below 3V.
The samples below were printed on 4 paper.
Distributed by: minilablaser.com
http://minilablaser.com/http://minilablaser.com/ -
7/25/2019 Frontier Print Frontier Print Quality nProblems
12/22
1
No. 010July, 1999
Equipment : SP1500/LP1500SC
Subject :
Auto Film Carrier Dust-Induced Streaked Unevenness
Countermeasures
Improvement &
CountermeasuresUN1 [ ]
Part No. Errata &
AdditionsUN2 [ ]
Technical
InformationUN3 [ ]
Product Infor. &
SpecificationsUN4 [ ]
Modification
control
No.
Field Equip.
Countermeasure
No.
If streaked unevenness is found on a print, it is suspected that it is caused by dust in the auto film carrier.
Instruct the users to take the following measures in the event of occurrence of this problem.
[Streaked unevenness patterns]
Unclear white streaks
Mixture of unclear and clear streaks (colorless or colored)
After removing dust from the opening in the film carrier pressure cover, the opening in the film mask, the
front and back sides of the diffusion plate, and the top surface of the mirror box, carry out scanner
correction at the time of pre-operational check.
[Important] Even if no dust is found in the cleaning, be sure to execute scanner correction at the time of
pre-operational check.
If scanner correction is executed at the time of pre-operational check, an operation designated as
brightness correction (shading correction) is effected. The term "brightness correction" refers to the
process of determining correction data such as would eliminate pixel-wise variations, by turning on
the light source lamp and monitoring the CCD sensor output with no film installed. If this operation
is performed, all the elements from the light source to the CCD sensor output will be corrected
uniformly, thereby removing irregularities from the light source and diffusion plate and eliminating
variations among the CCD sensor pixels. If brightness correction is made with dust deposited on the
film carrier, the CCD output for the dusty part will be subjected to unnecessary correction because
even if the dust has been removed prior to film scanning, the correction data is one which was
obtained in the presence of dust. This results in streaked unevenness on prints.
Factory Modifications : From Serial No. : Completion Date :
Field Countermeasures : [ ] Individually, with Charge [ ] Individually, Free of Charge [ ] All Free of Charge
Part Preparation : [ ]Order Basis
After Order Received [ ] Available : [ ] Being Prepared by: [ ]Automatic Distribution
by:
FRONTIER 350/370PROMPT TECHNICAL INFORMATION
Distributed by: minilablaser.com
http://minilablaser.com/http://minilablaser.com/ -
7/25/2019 Frontier Print Frontier Print Quality nProblems
13/22
FUJI PHOTO FILM CO., LTD.26-30, Nishiazabu 2-chome, Minato-ku, Tokyo 106-8620, Japan.
Ref. No. PP3-010 TD-99.7-FG(HB) Printed in Japan
Types of scanner correction and their descriptions
Scanner correction is roughly classified by timing and method into the following three types:
(1) At the time of pre-operational check [Required time: about 90 to 120 sec]
(2) At the time of new film carrier installation within the day of operation [Required time: about 90 to 120
sec]
The same scanner correction (brightness correction) as executed at the time of pre-operational
check is carried out.
(3) At the time of film carrier replacement (film carrier installation at the second and subsequent times)
within the day of operation [Required time: about 40 sec]
The presence of a film mask (darkness correction) and the film carrier ID are checked.
No brightness correction is made.
In the process of brightness correction, the brightness correction data obtained in the first session
are downloaded to the CDS circuit board (the circuit board in the image processing section for CCD
sensor output A/D conversion and correction).
NOTE: For film carrier installation at the second and subsequent times within the day of operation, be
sure to use the printing screen. If the film carrier is replaced using a screen other than the
printing screen, a message "Perform scanner correction in "Pre-operational check"" is
displayed when the printing screen appears and as a result, the time required for scanner
correction is elongated.
Distributed by: minilablaser.com
http://minilablaser.com/http://minilablaser.com/ -
7/25/2019 Frontier Print Frontier Print Quality nProblems
14/22
1
No. 013August, 1999
Equipment : LP1500SC
Subject : Y/R (Yellow/Red) Cast Fog on Prints
Improvement &
Countermeasures
Part No. Errata &
Additions
Technical
Information
Product Infor. &
Specifications
Modification
control
Field Equip.
Countermeasure
Y/R fog abruptly appears on prints.
This phenomenon is also observed on adjustment check prints such as upkeep prints.
The above phenomenon is attributable to reverse insertion of the CP-48S replenisher cartridge.
We checked the empty replenisher cartridge used and found a dent at the error insertion protect notch.
This indicates that P2RB entered P1R and mixed into P1. (The user forced the cartridge into the
equipment ignoring the correct installation direction).
When the amount of replenisher mixed is small, the above abnormality cannot be observed even after
control strip processing (FA9).
As the amount of replenisher mixed increases, the abnormality (stain: skin-colored, sensitivity: Dmax)
becomes obvious.
Although an error insertion protective mechanism is provided, please instruct the users again to install the
replenisher cartridge correctly.
We are now planning to devise an effective countermeasure in consideration of the present case.
Factory Modifications : From Serial No. : Completion Date :
Field Countermeasures : [ ] Individually, with Charge [ ] Individually, Free of Charge [ ] All Free of Charge
Part Preparation : [ ]Order Basis
After Order Received[ ] Avai lable : [ ] Being Prepared by: [ ]
Automatic Distribution
b :
FRONTIER 350/370PROMPT TECHNICAL INFORMATION
Distributed by: minilablaser.com
http://minilablaser.com/http://minilablaser.com/ -
7/25/2019 Frontier Print Frontier Print Quality nProblems
15/22
No. 026October, 1999
Equipment : LP1500SC/LP2000SC
Subject : Cyan Belt-like Image Print in the Main Scanning Direction
Improvement &Countermeasures
UN1 [ ]
Part No. Errata &Additions
UN2 [ ]
TechnicalInformation
UN3 [ ]
Product Infor. &SpecificationsUN4 [ ]
Modificationcontrol
No.
Field Equip.Countermeasure
No.
A cyan belt-like image appears on prints (regardless of print sizes) in the main optical scanning direction.
Further, the images on prints just before and following such a print are distorted.
Cyan belt-like image
Direction of travel Distorted
Pulse motor noise from the subscanning, sorting, and other sections is induced into the polygon rotation
control circuit in the laser unit of the output device, thereby giving rise to a temporary polygon rotation
error.
In order to eliminate the effect of the above noise, connect the junction cable to the "OPT1" connector on
the laser unit.
In previous cases, this phenomenon occurred in a relatively early stage of service.
If the phenomenon does not occur within the period of 10 days to 2 weeks after the start of operation, it is
therefore considered that the machine is unlikely to suffer from the above-described trouble.If this phenomenon should be observed in a machine in use in the field, immediately take the above
countermeasure to correct it.
When this phenomenon does not occur, take the countermeasure later when visiting local shops.
We are now keeping junction cables at the ready. As soon as junction cables become available, it will be
announced.
Factory Modifications : From Serial No. : Completion Date :
Field Countermeasures : [ ] Individually, with Charge [ ] Individually, Free of Charge [ ] All Free of Charge
Part Preparation : [ ]Order Basis After Order Received [ ] Available : [ ] Being Prepared by: [ ]
Automatic Distributionby:
FRONTIER 350/370PROMPT TECHNICAL INFORMATION
Distributed by: minilablaser.com
http://minilablaser.com/http://minilablaser.com/ -
7/25/2019 Frontier Print Frontier Print Quality nProblems
16/22FUJI PHOTO FILM CO., LTD.26-30, Nishiazabu 2-chome, Minato-ku, Tokyo 106-8620, Japan.
LP1500SC : #138 and #196 and above
LP2000SC : #16 and above
All machines in service
1. Turn the power switch to STANDBY, and the built-in
circuit breaker and the main power supply OFF.
2. Remove the densitometer.
3. Open the distribution section door.
4. Unscrew the four screws and remove the printer top
cover.
1. Disconnect the flat harness connector from the
operating panel.
2. Disconnect the fan connector.
3. Take out the ten screws securing the printer top inner
cover and remove the cover while pulling off the harness
through the hole in the cover.
1. Disconnect the connector (OPT1) and connect a
junction cable connector.
Printer Top Cover
Screws (4)
DensitometerPrinter Top Inner Cover
Screws (10)
Fan Connector
Flat Harness Connector
Operating Panel
Junction Cable Connector
Fan Connectors (3)
OPT1
Connectors (4)
IM318-15
Distributed by: minilablaser.com
http://minilablaser.com/http://minilablaser.com/ -
7/25/2019 Frontier Print Frontier Print Quality nProblems
17/22
1
No. ED026March, 2000
Equipment : LP1500SC/LP2000SC
Subject :
IMAGE ABNORMALITY (TRAILING END WHITE
BACKGROUND/STREAKS) COUNTERMEASURES SEE ED049
Improvement &
CountermeasuresUN1 [ ]
Part No. Errata &
AdditionsUN2 [ ]
Technical
InformationUN3 [ ]
Product Infor. &
SpecificationsUN4 [ ]
Modification
control
No.
Field Equip.
Countermeasure
No.
In the event of any of the following print image abnormalities, adjust or replace the steel belt (small) (P/L
2nd ed. LP10-86) in the sub-scanning unit.
(1) A white background appears at the trailing end of the print.
White background
(2) Streaks appear in the direction perpendicular to the direction of print travel.
Streaks
Slippage of the feed roller drive steel belt (small) (P/L 2nd ed. LP10-86) in the sub-scanning unit occurs
due to rubbing against the guide plate, thereby causing abnormal feeding of the paper.
Factory Modifications : From Serial No. : Completion Date :
Field Countermeasures : [ ] Individually, with Charge [ ] Individually, Free of Charge [ ] All Free of Charge
Part Preparation : [ ]Order Basis
After Order Received [ ] Available : [ ] Being Prepared by: [ ]Automatic Distribution
by:
INDEX Number Part Name Part Number
LP 10-86 Belt, flat 323D889734C
LP 12-A01 Sub scanning ass'y 810C889801B
Distributed by: minilablaser.com
http://minilablaser.com/http://minilablaser.com/ -
7/25/2019 Frontier Print Frontier Print Quality nProblems
18/22
1
No. 038November, 1999
Equipment : SP1500/SP2000
Subject : RP Tone Printing Setup
Improvement &
CountermeasuresUN1 [ ]
Part No. Errata &
AdditionsUN2 [ ]
Technical
InformationUN3
Product Infor. &
SpecificationsUN4 [ ]
Modification
control
No.
Field Equip.
Countermeasure
No.
"The print finish was of high contrast and hard on the eyes. The RP tone printing setting had been left on
"Yes". When it was reset to "No", the print finish became satisfactory."
The operator was automatically producing RP tone prints instead of normal prints, completely unaware of
the above condition.
(1) At the time of installation, set the "42C Image Correction Setup" "RP Tone Printing" to "Yes".
Factory Modifications : From Serial No. : Completion Date :
Field Countermeasures : [ ] Individually, with Charge [ ] Individually, Free of Charge [ ] All Free of Charge
Part Preparation : [ ]Order Basis
After Order Received [ ] Available : [ ] Being Prepared by: [ ]Automatic Distribution
by:
FRONTIER 350/370PROMPT TECHNICAL INFORMATION
Distributed by: minilablaser.com
http://minilablaser.com/http://minilablaser.com/ -
7/25/2019 Frontier Print Frontier Print Quality nProblems
19/22
FUJI PHOTO FILM CO., LTD.26-30, Nishiazabu 2-chome, Minato-ku, Tokyo 106-8620, Japan.
Ref. No. PP3-038 TD-99.11-FG Printed in Japan
(2) Next, set "42B Initial Printing Condition Setup 2" "RP Tone Correction" to "Yes". Set the tone
correction setting to "Normal" and then set "RP Tone Correction" back to "No". If "No" is selected,
then the menu bar RP tone correction default in (3) will be set to "No RP Tone Correction".
(3) Display the printing screen and click menu bar "Image Correct (4)" and "RP Tone Correct (3)". Select
"RP Tone Correction" "Yes" or "No".
Distributed by: minilablaser.com
http://minilablaser.com/http://minilablaser.com/ -
7/25/2019 Frontier Print Frontier Print Quality nProblems
20/22
1
No. 055February, 2000
Equipment : SP1500/SP2000
Subject : Image Abnormality (Face Shadow) Countermeasures
Improvement &
CountermeasuresUN1 [ ]
Part No. Errata &
AdditionsUN2 [ ]
Technical
InformationUN3
Product Infor. &
SpecificationsUN4 [ ]
Modification
control
No.
Field Equip.
Countermeasure
No.
In portraits, part of the image other than in the face area is excessively
high in density. Cases have arisen in which part of the image above the
face (outward in the film feed direction) has an excessively high density.
The problem occurs in the step of image processing for change of facial expression. The processing for
altering facial expression is performed as follows: a mask image is prepared by extracting the face from
the pre-scanned image, and enlarging it to the fine-scan image size for correction.
Of the enlargement ratios for enlargement to the fine-scan image size, the one in the film feed direction
was incorrectly calculated; the mask image was over-enlarged by about 30% in the film feed direction.
Since the mask and fine-scanned images were aligned with each others center, the corrected part was
shifted outward in the film feed direction. This phenomenon occurs regardless of the type of software(Ver.2.0 and Ver.3.0 with a face expression function), AFC, MFC, and film.
The avoid the occurrence of the problem, deactivate the functions of "RP-tone Correction" and "Face
Expression" by performing the following operations.
Select Setup and Maintenance menu and select SE1 and above level for user name.
Select Print Condition Setup and Check and Image Correction Setup.
Set RP-tone Correction and Face Expression to No. RP-tone Correction and Face
Expression appear only select Color Negative Film in Input Type .
After the above setup, it isnt necessary to restart the system.
Countermeasures will be taken when introducing Ver.4.0.
Factory Modifications : From Serial No. : Completion Date :
Field Countermeasures : [ ] Individually, with Charge [ ] Individually, Free of Charge [ ] All Free of Charge
Part Preparation : [ ]Order Basis
After Order Received [ ] Available : [ ] Being Prepared by: [ ]Automatic Distribution
by:
FRONTIER 350/370PROMPT TECHNICAL INFORMATION
Shadow
Feed direction
Distributed by: minilablaser.com
http://minilablaser.com/http://minilablaser.com/ -
7/25/2019 Frontier Print Frontier Print Quality nProblems
21/22
1
No. 057February, 2000
Equipment : LP1500SC
Subject :
Developer Rack Section (P1) Non-uniform Processing
Countermeasures
Improvement &
CountermeasuresUN1 [ ]
Part No. Errata &
AdditionsUN2 [ ]
Technical
InformationUN3 [ ]
Product Infor. &
SpecificationsUN4 [ ]
Modification
control
No.
Field Equip.
Countermeasure
No.
The upper section of the P1 rack has been changed so as to be of the same construction as that of the
LP2000SC.
As a measure against improper print finish (non-uniform processing), the section was changed to one
which as would allow the roller (P/No.334H0214A) to be locked.
Factory Modifications : From Serial No. : Completion Date :
Field Countermeasures : [ ] Individually, with Charge [ ] Individually, Free of Charge [ ] All Free of Charge
Part Preparation : [ ]Order Basis
After Order Received [ ] Available : [ ] Being Prepared by: [ ]Automatic Distribution
by:
FRONTIER 350/370PROMPT TECHNICAL INFORMATION
Drawing Part Number
Ref. No Current New
12 Gear, helical 327F2122501B Same as left (In common with LP2000SC)
13 Ring 25B8084241 Delete
14 Pin 319N2579A Same as left (In common with LP2000SC)
15 Guide 363H0146J 363H0146Q (In common with LP2000SC)16 Shaft 319F4483 Same as left (In common with LP2000SC)
17 Ring 25B8084241 Delete
18 Ring 25B8084241 Delete
19 Shaft 319F4548A Delete
21 Blade, squeegee 384F0071B Delete
26 Blade, squeegee 384F0071B Delete
58 Gear, spur 327F1121405B Delete
61 Support, shaft 31B7505880 Delete
66 Roller 334H0214A Delete
A01 Developer rack section (P1) 802H0327 802H0327B
Part Name
Distributed by: minilablaser.com
http://minilablaser.com/http://minilablaser.com/ -
7/25/2019 Frontier Print Frontier Print Quality nProblems
22/22
FUJI PHOTO FILM CO., LTD.26 30 Nishiazabu 2 chome Minato ku Tokyo 106 8620 Japan
1. The current type of rack is installed only in machines No.59 and below.
As a matter of fact, only nine machines, Nos.51-59 are affected.
The new type of rack is used for the machines No.60 and above.
For the machines No.59 and below, when taking countermeasures against non-uniform processing,
order a guide of the new type (P/No.363H0146Q) to make a new composition.
2. After the stocks of the parts indicated as deleted in the table are exhausted, order the new-type guide
(P/No.363H0146Q) to make the new configuration.
Distributed by: minilablaser.com
http://minilablaser.com/http://minilablaser.com/
top related