fresh concrete test en 206 – en 12350 · fresh concrete test en 206 – en 12350 ... fresh...
Post on 05-Apr-2018
369 Views
Preview:
TRANSCRIPT
A
CD
E
FF
G
B
F
1
Fresh concrete test
EN 206 – EN 12350EN 12350-5
Flow table completeconsisting of:• flow table with galvanized table plate• dimensions: 700 x 700 mm +/- 2 mm• weight of moveable table plate 16 +/- 0,5 kg• stroke height 40 mm• with 2 foot rests in front• with 2 steel squares in front• front edges of table plate provided with
buffer blocks• placing funnel upper Ø 130 mm lower Ø 200 mm height 200 mm• tamping bar made of hard woodOrder-No. B1814
Flow table without accessoriesconsisting of:• flow table with galvanized table plate• dimensions: 700 x 700 mm +/- 2 mm• weight of moveable table plate 16 +/- 0,5 kg• stroke height 40 mmOrder-No. B18143
Placing funnel• upper Ø 130 mm• lower Ø 200 mm• height 200 mmOrder-No. B18141
Dirt collar• for put up on the placing funnelOrder-No. B18144
Tamping bar • made of hard woodOrder-No. B18142
EN 12350-1Slump-Test Set
consisting of:• plastic plate 500 x 500 x 10 mm • placing funnel upper Ø 100 mm lower Ø 200 mm height 300 mm• tamping bar made of steel Ø 16 x 600 mm,
rounded at one end Order-No. B1901
Bevelled straight edge • made of steel• with facet• lenght 400 mmOrder-No. B1613
A
B
C
D
E
F
G
A
B
C
D
E
F
G
2
Fresh concrete test
EN 206 – EN 12350EN 12350-3
VEBE setting-time-measuringequipment
consisting of:• vibrating unit with frequency control for
50-60 Hz• amplitude 0,5 mm• cylindrical container• placing funnel• swivel arm with height adjustable, fixable,
transparent disc• tamping bar• electrical connection 230 Volt/50 HzOrder-No. B1902
EN 12350-7Air entrainment meter for testing of air content of fresh concretePressure compensation method
• test container volume 8 ltr.• 2 carrying grips on test container• manometer protection and carrying grip
for top• incl. calibration equipment (each one test
tube straight and bent)• washing bottle 1000 ml• operation manualOrder-No. B2020
Filling ring • for air entrainment meter B2020Order-No. B2021
Transport- and storage suitcase• for air entrainment meter B2020• stable aluminium suitcase• two solid and safe one hand tension locks• venting slots• cover opening with carrying gripOrder-No. B2024
EN 12350-4Compactibility container Walz
• Walz container • dimensions: 200 x 200 x 400 mm Order-No. B2001
Hand shovel• for sampling made of aluminium • content 450 cm³ Order No. S0809
Hand shovel• for sampling made of aluminium • content 900 cm³ Order No. S0810
A
B
C
D
E
F
G
C
B
A
E
D
B
A
3
Fresh concrete test
EN 206 – EN 12350DIN 1048-1
Drying device• for fresh concrete• for determination of water/cement value• made of stainless steel• only for propane gas connection• with high pressure hose, hose break proof
equipment and regulator• without drying panOrder-No. L0510
Drying pan• made of galvanized steel sheet• with 2 handles • dimensions: 400 x 300 x 100 mmOrder-No. L0511
Electronic platform balance • with separate display• height of numbers: 25 mm• IP 65• with data interface RS 232• for operation by power supply unit or by
storage battery (option)• weighing platform made of stainless steel
310 x 300 mm• weighing capacity 0 ... 30 / 60 kg• resolution 10 / 20 g• with supply unit 230 VoltOrder-No. O03510
Electronic compact balance • with integrated display• height of numbers: 25 mm• with data interface RS 232• for operation by power supply unit or by
storage battery (option)• underfloor weighing unit• weighing platform made of stainless steel
340 x 240 mm• weighing capacity 0 ... 30 kg• resolution 1,0 g• with supply unit 230 VoltOrder-No. O0436
Electronic platform balance• with separate display• with innovative touchscreen• IP 65• with data interface RS 232• weighing platform made of stainless steel• weighing platform 315 x 305 mm• weighing capacity 0 ... 30 kg• resolution 0.5 g• with supply unit 230 VOrder-No. O014501
A
B
C
D
E
A
B
C
D
E
F
4
Fresh concrete test
EN 206 – EN 12350Concrete-penetrometer
• for estimating of hardeningOrder-No. B19082
Concrete-digital thermometer• with LCD-digital display• height of numbers 5 mm• probe made of stainless steel• with protective cover and clip• measuring range -50 ... +200 °C• resolution 0.1 °C• length 125 mmOrder-No. R0110
Concrete-digital thermometer like R0110 but with• length 300 mmOrder-No. R0112
Concrete-thermometer• big LCD-display• height of numbers 15 mm• functions test - Max - Min - Hold• stick-in probe 100 mm• with cable 100 cm• measuring range -40 ... +200 °C• resolution 0.1°COrder-No. R0114
Infrared-thermometer• big LCD-display • height of numbers 8 mm • measuring range -35 ... +365 °C• resolution 0.1°C• reaction time 1 secondOrder-No. R0201
Aerometer• for the determination of density of rest water • measuring range
1.0 – 1.15 g/cm³ (1000-1500 kg/m³)• resolution 0.001 g/cm³ (1 kg/m³)• total length 350 mm• packing unit 3 piecesOrder-No. T30100
FORM+TEST Seidner & Co. GmbHPost box 1154 • D-88491 Riedlingenphone: +49 (0) 7371 9302-0 • fax: -99
www.formtest.desales@formtest.de
L122
.02E
• Fr
isch
beto
nprü
fung
.indd
• 11
/201
3
A
B
C
D
E
F
A
B
C
D
1
Self-compacting concreteSVB / SCCEN 12350
Working plate – flow plate• dimensions: 900 x 900 x 30 mm• with lateral grip• with mark (reference circles)
for placing funnel Ø 210 mm• for T-500 mm - measuringOrder-No. B19022
Working plate – flow plate • with automatic measuring of flow time and of
flow measure• dimensions: 900 x 900 x 100 mm• on top galvanized sheet, round off by 2 mm• with marks (reference circles)
for placing funnel Ø 210 mm• blocking ring Ø 300 mm• with installed measuring electronics for
automatic measuring of flow movement / time -display of absolute flow degree
• this will be measured by 4 symmetrically situated sensors which are installed in the table plate (shockproof and watertight)
• with record of the time necessary till the measure t500 is reached. Including software for presentation of movement and times in form of tables or graphic at PC / laptop
• automatic determination of end of flow measurement
• the data can be stored and printed• resolution way: 5 mm• resolution time: 0.005 sec.• measuring way: 400 - 800 mmOrder-No. B19025
Blocking ring - J-Ring • adjustable execution• 16 rods Ø 18 mmOrder-No. B18355
Placing funnel• upper diameter: 100 mm• lower diameter: 200 mm• height: 300 mmOrder-No. B19011
• as before, but without foot flapsOrder-No. B19012
A
B
C
D
A
B
C
D
E
2
Self-compacting concreteSVB / SCCEN 12350
V-funnel for concrete test• for determination of relative flow time RB• for determination of flow speed and viscosity
of self compacting concrete• dimensions: 75 x 515 mm• outlet width: 65 mm• total height: 600 mm• made of stainless steel• with foot frameOrder-No. B1834
Hopper for V-funnel• made of stainless steelOrder-No. B18342
L-Box • for judgment of level and the flow times of
self compacting concrete• complete made of stainless steel• dimensions: 700 x 200 x 600 mmOrder-No. B1839
Bevelled straight edge • made of steel• with facet• length: 400 mmOrder-No. B1613
Hand shovel • for sampling made of aluminium• content 450 cm³Order-No. S0809• content 900 cm³Order-No. S0810
Table stop watch • analogues display • 2 button operation• start - stop - reset - addition• 0-60 sec. and 1/100 min.Order-No. S20123
FORM+TEST Seidner & Co. GmbHPost box 1154 • D-88491 Riedlingenphone: +49 (0) 7371 9302-0 • fax: -99
www.formtest.desales@formtest.de
L130
.02E
• S
elbs
tver
dich
tend
er B
eton
.indd
• 11
/201
3
A
B
C
D
E
A
B
C
D
EF
G
H
I
J
1
Hardened concrete test
EN 12390Specimen cube mould 150 x 150 mm
• for production of specimens• special plastic, black, one-part,
with holding border• rapid take out through water or air pressureOrder-No. B1521
Plastic plugs• for specimen cube mould B1521• packing unit each 100 pc.Order-No. B15211
Demoulding support• for specimen cube mould B1521• for an easy demouldingOrder-No. B1523
Specimen cube mould150 x 150 mm
• for production of specimens• special steel construction, 2 parts,
screwed, splitted diagonallyOrder-No. B1531
Specimen cube mould150 x 150 mm
• made of grey plastic, one-part, with holding border
• rapid take out through water or air pressureOrder-No. B1515
Cover for specimen cube mouldOrder-No. B1516
Cube labels• with imprint grey • approx.140 x 140 mm• packing unit each 100 pc. Order-No. B152130
Compressed air demouldingpistol
• with 10 m tube and connection pieceOrder-No. B15200
Electric vibrating table • for compacting of fresh concrete• with foot switch• 2.5 m cable with plug• galvanized execution• table size 310 x 310 mm• rotations per minute 3000 rpm.• electric connection 230 V / 50 Hz• weight approx. 17.5 kgOrder-No. B17134
Electric vibrating table • as before, but with• connection by car-truck plug (cigarette lighter)• electric connection 12 V• weight approx. 17.5 kgOrder-No. B17135
A
B
D
E
F
G
H
I
J
C
A
BC
D
E
2
Hardened concrete test
EN 12390High frequency vibrating table
• with timer (0 - 120 sec.)• long-duration switch• including 2.5 mtrs. of cable and plug• galvanized execution• table plate with bordering
(at 2 diagonal corners)• table size 330 x 550 mm• rotations per minute 9000 rpm• electric connection 220 V / 50 Hz• weight approx. 34 kgOrder-No. B17182
Electronic platform balance• with separate display• IP 65• weighing platform made of stainless steel• weighing platform 310 x 300 mm• weighing capacity 0 ... 30 / 60 kg• resolution 10 / 20 g• with supply unit 230 VOrder-No. O03510
Electronic platform balance• with separate display• with innovative touchscreen• IP 65• with data interface RS 232• weighing platform made of stainless steel• weighing platform 315 x 305 mm• weighing capacity 0 ... 30 kg• resolution 0.5 g• with supply unit 230 VOrder-No. O014501
Climatic box• made of plastic• for the storing of 15 cubes 150 x 150 mm• thermo controller with digital display• cover• floor grid made of hard woodOrder-No. B2110
Compression- and bendingtesting machines for quality management of your products
FORM+TEST Seidner & Co. GmbHPost box 1154 • D-88491 Riedlingenphone: +49 (0) 7371 9302-0 • fax: -99
www.formtest.desales@formtest.de
L140
.02E
• Fe
stbe
tonp
rüfu
ng.in
dd •
12/2
013
A
B
C
D
E
1
Hardened concrete test
Compression testing machineBETA 5-2000 A●accuracy according to
DIN EN ISO 7500-1, class 1●execution acc. to EN
12390-4 (Strain test execution)
●for compression strength tests according to EN 12390-3, EN 12504-1 and EN 206
●with automatical load increase, control via digital controller DIGIMAXX® C-22 in closed loop system
Technical dates - testing frame
●testloadmax.:2,000kN●workingpressuremax.:407bar●pistonstroke:50mm●upperplaten:Ø300mm●thicknessofupperplaten:40mm●lowerplaten:Ø300mm●thicknessoflowerplaten:55mm●hardnessofplatens:55HRC●tstchamberheight:330mm●cleardistancebetweencolumns(width):230mm
●cleardistancebetweencolumns(depth):175mm
●measuringrange:80...2,000kN●displayrange:0...2,000kN●electronicloadmeasuringbypressuretransducer
●voltage:230Volt,50Hz,1,5kW●weight:725kg
2
A
D
B C
Technical dates - digital controller
●LCD-screen-display,5numbers,16Bitprocessortechnology
●resolution60,000Digits
●automaticzeropointcorrection
●programmablecalculationofthestrengthof10differentspecimensaswellasthecorrespondingstandardspeeds
●displayofthestrengthinN/mm²orMpa
●adjustabledisplayinkN,N,kg,kp,toorbar
●peakvaluememoryandresetkey
●codeprotectedcalibration/linearization
●serialinterfaceRS232orUSBtorecallthepeakvalue
●memory
Accessories:
forreductionoftestchamberheight
distanceplates,hardened,surfacegrinded,forinsertbetweencompressionplateandpiston.
dimensions210x210x110mm,38kgdimensions170x170x50mm,12kg
dimensions120x120x50mm,6kg
centerringdevicesforcompressionplates
centerringdevicesfordistancepieces
Options:
●builtinprinter
●transfersoftwareWinTrans
buildingmaterialtestsoftwarePROTEUSP
M 5
02.0
2E •
BE
TA5-
2000
A.in
dd •
01/2
014
• Tec
hnic
al m
odifi
catio
ns re
serv
ed!
FORM+TEST Seidner & Co. GmbHPostbox1154•88491Riedlingen
phone:+49(0)73719302-0•fax:-99www.formtest.desales@formtest.de
A
B
C
D
1
Hardened concrete test
Compression testing machineALPHA 3-3000 S●accuracyaccordingto
DIN EN ISO 7500-1, class 1●executionacc.toEN12390-4 (straintestexecution)
●forcompressionstrengthtests according to EN12390-3,EN12504-1andEN206
●separatedrivestation AS-C20-N
●withautomaticalloadincrease,controlviadigitalcontroller DIGIMAXX®C-20inclosedloopsystem
Technicaldates-testingframe
●testloadmax.:3,000kN●workingpressuremax.:397bar●pistonstroke:100mm●upperplaten:Ø320mm●lowerplaten:Ø300mm●thicknessofplatens:75mm●hardnessofplatens:55HRC●testchamberheight:340mm●cleardistancebetweencolumns(width):355mm
●cleardistancebetweencolumns(depth):255mm
●rigidity:2,950kN/mm●measuringrange:60...3,000kN●displayrange:0...3,000kN●electronicloadmeasuringbypressuretransducer
●voltage:3x400Volt,50Hz,1.5kW●weight:1,810kg
Picture: Testing machine frame with chromium plated machine‘s columns (options)
2
A B
C
D E
Technical dates - digital controller●LCD-screen-display,5numbers,16Bitprocessortechnology
●resolution60,000Digits●automaticzeropointcorrection●programmablecalculationofthestrengthof30differentspecimensaswellasthecorrespondingstandardspeeds
●displayofthestrengthinN/mm²oderMpa●adjustabledisplayinkN,N,kg,kp,toorbar
●peakvaluememoryandresetkey●codeprotectedcalibration/linearization●serialinterfaceRS232torecallthepeakvalue
Accessories:
forreductionoftestchamberheight distanceplates,nothardened,surfacegrinded,forinsertbetweencompressionplateandpiston.Fixturewithlocatingpin.
dimensionsØ300x50mm,27kg dimensionsØ300x60mm,33kg distancepieces,hardened,surfacegrin-ded,forputonofthecompressionplate
dimensions210x210x110mm,38kg dimensions170x170x50mm,12kg dimensions120x120x50mm,5,65kg
Options:
●connectionoffurther(max.4)testingmachines
●biggercompressionplates dimensions320x420x75mm dimensions320x520x75mm●highertestchamber(workingarea)●machine‘scolumnschromiumplated●builtinprinter●transfersoftwareWinTrans buildingmaterialtestsoftwarePROTEUS
centerringdevicesforcompressionplates
centerringdevicesfordistancepieces
PM
301
.02E
• A
LPH
A3-
3000
S.in
dd •
01/2
014
• Tec
hnic
al m
odifi
catio
ns re
serv
ed!
Picture: Drive Station AS-C-20N-PC (option)
FORM+TESTSeidner&Co.GmbHPostbox1154•88491Riedlingen
phone:+49(0)73719302-0•Fax:-99www.formtest.desales@formtest.de
A
B
C
D
E
1
Bending / Flexure testing machine DELTA 4-100 D-S●accuracy acc. to DIN EN ISO
7500-1, class 1●forflexurestrengthtestson
materials acc. EN 12390-5, EN 1343, EN 1344
●with options also acc. EN 1340●with automatical load increase,
control via digital controller DIGIMAXX® C-22 in closed loop system
Technical dates - testing frame●2columnsframe●singleactingtestcylinder●testloadmax.:100kN●workingpressuremax.:199bar●pistonstroke:80mm●testchamberheight:165mm●bendingrollerlength:210mm●bendingrollerØ:40mm●lowerbendingrollerdistance70..600mm●basicequipmentincludestheinsertfor3-pointload
●cleardistancebetweencolumns:240mm●measuringrange:4.00...100kN●displayrange:0...100kN
●electronicloadmeasuringbyprecisionelectronicpressuretransducer
●voltage:3x400volt,50Hz,1,5kW●weight:appr.400kg
●availablewithfollowingtestloadsforcompression:60kN,100kNand200kN
2
A
B B
Technical dates - digital controller●LCD-screen-display,5numbers
●resolution60,000digits
●automaticzeropointcorrection
●programmablecalculationofthestrengthof10differentspecimensaswellasthecorrespondingstandardspeeds
●displayofstrengthinN/mm²orMpa
●adjustabledisplayinkN,N,kg,kp,toorbar
●peakvaluememoryandresetkey
●codeprotectedcalibration/linearization
●serialinterfaceRS232torecallthepeakvalue
Options:●highertestchamber(220mm)
●enlargementofpistonstroke(130mm)
●enlargementofbendingtable(70...900mm)
insertfor4-pointload
●pressurestampforcurbstonesØ40mmacc.EN1340
buildingmaterialtestsoftwarePROTEUS
●transfer-softwareWinTrans
●built-inprinter
PM
401
.02E
- D
ELT
A 4-
100D
-S.in
dd -
12/2
013
• Tec
hnic
al m
odifi
catio
ns re
serv
ed!
FORM+TEST Seidner & Co. GmbHPostbox1154•D-88491Riedlingenphone:+49(0)73719302-0•fax:-99
www.formtest.desales@formtest.de
A
B
1
Bending / Flexure testing machine DELTA 5-300●accuracyacc.toDINENISO
7500-1, class 1●forflexurestrengthtestsonmaterialsacc.EN12390-5, EN1339,EN1343,EN1344
●withoptionsalsoacc.EN1338splittingtestonpavingstones,EN1340andforcompressiontests
●separatedrivestationAS-C20-N●withautomaticalloadincrease,controlviadigitalcontrollerDIGIMAXXC-20inclosedloopsystem
Technicaldates-testingframe
●4columnsframe●rigidconstruction●doubleactingtestcylinder●testloadmax.300kN●workingpressuremax:288bar●pistonstroke:220mm●testchamberheight:220mm●bendingrollerlength:510mm●bendingrollerØ:40mm●lowerbendingrollerdistance80..1020mm
●basicequipmentincludestheinsertfor3-pointload
●measuringrange:3.00...300kN●displayrange:0...300kN
●electronicloadmeasuringbyprecisionelectronicloadcell
●voltage:3x400volt,50Hz,1,5kW●weight:appr.1470kg
●availablewithfollowingtestloadsforcompression:100kN,200kNand300kN
2
A B
C D
Technicaldates-digitalcontroller● LCD-screen-display,5numbers
● resolution60.000digits
● automaticzeropointcorrection
● programmablecalculationofthestrengthof30differentspecimensaswellasthecorrespondingstandardspeeds
● displayofstrengthinN/mm²orMpa
● adjustabledisplayinkN,N,kg,kp,toorbar
● peakvaluememoryandresetkey
● codeprotectedcalibration/linearization
● serialinterfaceRS232torecallthepeakvalue
Options: insertfor4-pointload
● pressurestampforcurbstonesØ40mmacc.EN1340
splittingdeviceacc.EN1338
setofplatenØ230x40mmwithfloatingaxle(ballseat)
compressiondeviceDV600AZusableinconnectionwithsetofplaten
● executionforfibreconcretetest
● electronicdisplacementmeasuringandcontrolequipment
● equipmentforbendingdeformation
● buildingmaterialtestsoftwarePROTEUS
● transfer-softwareWinTrans
● built-inprinterP
M 5
53.0
2E -
DE
LTA
5-30
0.in
dd •
01/2
014
• Tec
hnic
al m
odifi
catio
ns re
serv
ed!
PictureshowsAS-C-20N-PC(option)
FORM+TESTSeidner&Co.GmbHPostbox1154•D-88491Riedlingenphone:+49(0)73719302-0•fax:-99
www.formtest.desales@formtest.de
A
D
B
C
1
Compression- and Bending testing machine MEGA 6-3000-100●accuracy acc. to DIN EN ISO
7500-1, EN 12390-4, class 1 - straintest execution
●for compression strength tests acc. to EN 12390-3, EN 12504-2
●for bending tests acc. to EN 12390-5, EN 1339, EN 1341
●with accessories also for curb-stone tests acc. to EN 1338, EN 1340, EN 1343 as well as compression strenghts on cement and mortar acc. to EN 196 / EN 1015
●separate drive station AS C 20 N-2, automatic load increase through digital controller DIGIMAXX® C-20 in closed loop system with permanent compari-son of nominal value and actual value
Technical dates – compression test●testloadmax.:3000kN●pistonstroke:100mm●uppercompressionplate:Ø320mm●lowercompressionplate:Ø300mm●hardnessofcompressionplates:53HRC●testchamberheight:340mm●cleardistanceoftestingframe:355x255mm
●measuringrange:60,00...3000kN●displayrange:0...3000kN●loadmeasuringviaelectronicalprecisionliquidpressuretransducer
Technical dates – bending test●testloadmax.:100kN●pistonstroke:220mm●testchamberheight:220mm●bendingrollerlength:510mm●bendingroller:Ø40mm●bendingrollerdistance:80...900mm●measuringrange:1.00...100kN●displayrange:0...100kN●loadmeasuringviashearforcewear-resistantelectronicprecisionloadcell
●voltage:3x400Volt,50Hz,1.5kW●weight:approx.2310kg
DC
A
E
B
2
Technical dates – digital display● LCD-screen-display,5numbers
● resolution60,000digits
● automaticzeropointcorrection
● programmablecalculationofthestrengthof30differentspecimensaswellasthecorrespondingstandardspeeds
● displayofstrengthinN/mm²orMpa
● adjustabledisplayinkN,N,kg,kp,toorbar
● peakvaluememoryandresetkey
● codeprotectedcalibration/linearization
● serialinterfaceRS232torecallthepeakvalue
OPTIONS:● highertestchamber
● biggercompressionplates dimensions320x320x75mm dimensions320x420x75mm dimensions320x520x75mm
Ainsertfor4-pointload
Opressurestampforcurbstones
Bsetcompressionplateswithpendulumaxle
CcompressiondeviceDV600AZonlyuseableinconnectionwithsetcompressionplates
DbendingdeviceBV10OMonlyuseableinconnectionwithsetcompressionplates
EbuildingmaterialtestsoftwarePROTEUS
Oelectronicdisplacementmeasuringandcontrolequipment
Obuiltinprinter
Available with following test loads:● forcompressiontest: 2000,3000,4000kN
● forbendingtest: 100,200,300kN
PM
M 6
30.0
2E -
ME
GA
6-30
00-1
00.in
dd -
01/2
014
• Tec
hnic
al m
odifi
catio
ns re
serv
ed!
FORM+TEST Seidner & Co. GmbHPostbox1154•D-88491Riedlingenphone:+49(0)73719302-0•fax:-99
www.formtest.desales@formtest.de
1
Specimen grinding machine PSM 3/230●for grinding of specimens
made of concrete, high-strength concrete, natural stone, screed, fireresistantproducts,asphaltetc.
●for grinding of specimens acc. to EN 12390-3 and EN 12504-1
●height adjustable and corrosion-protected grinding table
●energyefficientmachine`sdrivewith gently start
●directcoolingwatersupplybyhollow main spindle
●completeworkingareawithstainless-steel water protection
●ergonomicplacedoperationpanelTechnical dates:grinding area: 220 x 220 mmswivelling range: r=390 mmplan parallelism (over 200 mm): 0.05 mmclamping height max: 350 mmclamping height min*: 40 mm (*depending on the clamping device)height adjustment per revolution: 0.25 mm
voltage: 400 Volt / 50 Hz.
dimensions (approx.) width x depth x height: 970 x 932 x 1900 mmarea: 750 x 700 mm
weight (approx.): 620 kg
Deliveryvolume:clamping device for cubes 200 x 200 mm, 150 x 150 mm and grinding wheel Ø 230 mm
P0500
Accessories:P0530 electromotoric height adjustment
P0323 clamping device swivelling by 180°, for Ø 40 ... 160 mm, height 80 ... 320 mm
P0324 clamping device swivelling by 180°, for Ø 40 ... 70 mm, height 40 ... 70 mm
the specimens must be clamped only one time
P0314 mud storage tank
P0534 mud storage tank with water pump
2
Core resp. cylinder grinding machine PSM 4●for grinding of specimens made
of concrete, natural stone, screed, fireresistantproductsetc.
● cores resp. ● cylinders
●for grinding of specimens acc. to EN 12390-3 and EN 12504-1
●for cylinder / cores until max. Ø 100 mm
●verticaladjustablegrindingwheel●directcoolingwatersupply●workingareainfrontwithAcryl
glass-protection
Technical dates:grinding area: 85 x 85 mm resp. Ø 110 mmplan parallelism (over 75 mm): 0.05 mmclamping height max: 110 mmclamping height min: 40 mmvertical adjustment per rotation: 0.4 mm
voltage: 400 Volt / 50 Hz.
dimensions (approx.) width: 560 mm depth: 600 mm height: 800 mm
weight (approx.): 135 kg
Deliveryvolume:with grinding wheel Ø 130 mm
P0401
Accessories:P0405 Clamping device swivelling by 180°,
for Ø and height 40 ... 100 mm.The specimen must be clamped only one time.
L114
.02E
- P
SM
3-4
.indd
- 04
/201
2
FORM+TEST Seidner & Co. GmbHPost box 1154 • D-88491 Riedlingenphone: +49 (0) 7371 9302-0 • fax: -99
www.formtest.desales@formtest.de
1
Water penetration test
DIN EN 12390-8, EN 206• to test concrete specimens
150 x 150 x 150/ 120 mm as well as 200 x 200 x 200 / 120 mm (only with options)
• up to max. 10 bar working pressure (Special construction possible until 12 bar)
• Rapid clamping of specimens by a central threaded spindle installed above. A new construction guarantees an absolute impermeability of the test benches.
• Rust prevention in wet part by used materials.
• Separate loops for each 3 test benches, adjustable by a fine regulation valve and works calibrated manometer which is appropriate for calibration.
WE 3 OMZ• with 3 test benches• without quantitative water measuringOrder-No. B1320
WE 3 MMZ• with 3 test benches• with quantitative water measuringOrder-No. B1321
WE 6 OMZ• with 6 test benches• without quantitative water measuringOrder-No. B1322
WE 6 MMZ• with 6 test benches• with quantitative water measuringOrder-No. B1323
2
Water penetration test
DIN EN 12390-8, EN 206
ROTA 6 M• with 6 test benches• ergonomic, all test benches at same
working height, space saving and rotateable
• with quantitative water measuringOrder-No. B1352
Accessories:
Compressor• for max. 8 bar air pressure• special construction - extremely silentOrder-No. B13065
Rubber sealing rings• Ø 75/160• 1 set = 6 piecesOrder-No. B13071
Rubber sealing rings• Ø 100/160• 1 set = 6 piecesOrder-No. B1307
Manometer • with MPA-calibration certificateOrder-No. B13081
FORM+TEST Seidner & Co. GmbHPost box 1154 • D-88491 Riedlingenphone: +49 (0) 7371 9302-0 • fax: -99
www.formtest.desales@formtest.de
L101
.03E
• W
asse
rein
drin
gprü
fung
.indd
• 03
/201
3
A
B
C
D
1
Aggregates
EN 12620 - EN 933EN 13055-1 EN 13139DIN 4226 - 100Particle size distribution EN 933-1
Laboratory sieve shaker type EML 315 digital T
• for dry sieving• max. sieving capacity approx. 6 kg• with quick clamping system TwinNut • for 8 normal sieves (60 mm height) or
14 reduced sieves (30 mm height)• possible diameter 300, 250 and 200 mm• delivery including machine cover with
inspection glassOrder-No. N05090
Laboratory sieve shakertype EML 315 digital plus N
• for wet and dry sieving• separate controller• with quick clamping system TwinNut • delivery including machine cover with
inspection glass and spreading spray• water plug with socket,• 2 hose clamps, 3 m PVC water hoseOrder-No. N05091
Laboratory sieve shakertype EML 450 digital plus T
• for dry sieving• max. sieving capacity approx. 15 kg• with quick clamping system TwinNut • possible diameter 450, 400, 350, 315,
305, 300 mm• delivery including machine cover with
inspection glassOrder-No. N0510
Laboratory sieve shakertype EML 450 digital plus N
• for wet and dry sieving• separate control unit• with quick clamping system TwinNut • delivery including machine cover with
inspection glass and spreading spray• water plug with socket,• 2 hose clamps, 3 m PVC water hose Order-No. N0512
A
B
C
D
C
A
E
F
B
D
2
Aggregates
Particle size distribution EN 933-2
Sieves with stainless steel frame• deliverable diameters: 100, 200, 203, 300,
305, 315, 400 mm• mesh sizes from 0.020 to 3.55 mm• square hole sizes from 4.0 to 125 mm
(depending on diameter)
Sieves with aluminium frame• mesh or perforated plates can be replaced• deliverable diameter: 400 mm• mesh sizes from 0.020 to 3.55 mm• square hole sizes from 4.0 to 125 mm
Sieves with hardwood frame• mesh or perforated plates can be replaced• available sizes: 300 x 300 and
500 x 500 mm• mesh sizes from 0.045 to 3.55 mm• square hole sizes from 4.0 to 125 mm
Particle shape flakiness indexEN 933-3
Grid sieves 300 x 300 mm• with holding edge around• slot widths from 2.5 to 40.0 mm
Particle shape – shape indexEN 933-4
Grain shape sliding caliper 1:3• made of rust proof steel• acc. to DIN 52 114 and EN 933-4Order-No. N0450
Electronic laboratory balance• compact balance with LCD-display • weighing platform made of stainless steel• weighing platform 200 x 160 mm• weighing capacity 16 100 g• resolution 0.1 g• with power supply unit 230 VOrder-No. O01133
FORM+TEST Seidner & Co. GmbHPostfach 1154 • D-88491 Riedlingenphone: +49 (0) 7371 9302-0 • fax: -99
www.formtest.deinfo@formtest.de
L150
.02E
- G
este
insk
örnu
ng.in
dd •
11/2
013
A
B
C
D
E
F
1
A
B
C
D
Cement test
EN 196Mortar mixer
• for production of standard prisms• with programme automatic• 2 mixing speeds: 140 to 285 min. • sand feeding device• prepared to connect water dosage device.• weight approx. 90 kg• electric connection 400 V / 50 Hz / 0.75 kW• dimensions approx. (DxWxH):
350 x 650 x 750 mmOrder-No. B2760
Mortar mixer• as before, but with water dosage deviceOrder-No. B2762
Automatic Vicat-Needle device• stiffness begin – stiffness enddelivery volume:• needle Ø 1.13 mm• needle Ø 1.13 mm with special foot• immersion rod Ø 10 mm• hard rubber ring Ø 70 / 80 mm• glass plate• registration paper• additional weight 200 g• tool set
(allen type wrench 2.0 and 2.5 mm)Order-No. B26660
Accessorias:Needle cleaner
• (see detail picture)Order-No. B26670
Vicat-Needle device• stiffness begin – stiffness enddelivery volume:• needle Ø 1.13 mm• needle Ø 1.13 mm with special foot• immersion rod Ø 10 mm• hard rubber ring Ø 70 / 80 mm• glass plateOrder-No. B26091
LeChatelier Ring• made of brass• for determination of volume consistency of
cement• with 2 measuring tops• incl. 2 glass platesOrder-No. B2601
A
B
C
D
2
A
B
C
D
Cement test
EN 196Jolting table
• for compacting of specimens• dimensions:
jolting table 1100 x 400 x 280 mm switch box 200 x 300 x 120 mm
• weight: jolting table 55 kg switch box 8 kg
• electric connection 230 V / 50 HzOrder-No. B2830
Vibrating table• for compacting of specimens• table plate: 400 x 300 mm• stainless steel table plate• vibrations: 3000 rpm.• clamping device for specimen mould• vibration width setting• vibration width display• timer-DigitalOrder-No. B2808
Precision Three-gang-mould• with bore holes for shrinkage measuring pins• all parts chemical nickeled• surface grinded• webs and nut plates marked • dimensions W/D/H: 160 x 40 x 40.1 mmOrder-No. B2709222
Precision Three-gang-mould• as before but without bore holes for
shrinkage measuring pinsOrder-No. B270925
Adapter boxOrder-No. B2710
FORM+TEST Seidner & Co. GmbHPost box 1154 • D-88491 Riedlingenphone: +49 (0) 7371 9302-0 • fax: -99
www.formtest.desales@formtest.de
L170
.02E
• Ze
men
tprü
fung
.indd
• 11
/201
3
A
B
C
D
A
B C
D
E
1
Mortar test
DIN EN 459-2 DIN EN 1015
Air entrainment meter• for testing of air content in fresh mortar• incl. washing bottle 1000 ml • content 1 ltr.Order-No. B2030
Extension collar• for air entrainment meter B2030Order-No. B2031
Pot 1 LitreOrder-No. B2030-18
Haegermann-flow table• for flow tests• manually operated, with counter • complete with stainless steel plate Ø 300 mm• funnel Ø 70/100 mm, height 60 mm,
material thickness 2 mm• extension collar and hand tamperOrder-No. B29025
Haegermann-flow table• for flow tests• manually operated, without counter • complete with stainless steel plate Ø 300 mm• funnel Ø 70/100 mm, height 60 mm,
material thickness 2 mm• extension collar and hand tamperOrder-No. B29015
Haegermann-flow table• for flow tests• with electric drive and counter • complete with stainless steel plate Ø 300 mm• funnel Ø 70/100 mm, height 60 mm,
material thickness 2 mm• extension collar and hand tamper• electric connection: 230 V / 50 HzOrder-No. B2820
Haegermann-flow tables also deliverable with alu / glassplate.
A
B
C
D
E
A
B
C
D
E
2
Mortar test
DIN EN 459-2 DIN EN 1015
Stiffness measuring apparatus• for testing of properties of masonry cementconsisting of:• stand, falling rod, measuring pot and
hand tamper Ø 40 mm • falling weight totally 90 g• falling height 100 mmOrder-No. B2670
Mortar mixer• 2 mixing speeds (140 and 285 rpm)• incl. mixing pan with 5 ltr. content made of
stainless steel and flat stirrer made of stainless steel
• electric connection: 230 V / 50 Hz / 13 kW• dimensions (DxWxH): 380 x 260 x 430 mmOrder-No. B27010
Mortar mixer• infinitely varibale mixing speeds• mixing pan with 5 ltr. content and flat stirrer
made of rust free steel• electric connection: 230 V, 50 Hz, 0,5 kW• dimensions approx. (DxWxH):
closed 462 x 240 x 400 mm opened 462 x 240 x 550 mm
Order-No. B27020
Three gang mould• light execution• surface yellow passivated• dimensions: 40 x 40 x 160 mmOrder-No. B2709
Hand tamper• acc. to DIN 18 555, part 7• dimensions: 150 x 20 mmOrder-No. B2711
Hand tamper• acc. to DIN 52 450• dimensions: 110 x 20 mmOrder-No. B2712
A
B
C
D
E
A
B
C
D
3
Mortar test
DIN EN 459-2 DIN EN 1015
Three gang mould• made of polystyrene• without cover• 1 packing unit = 225 piecesOrder-No. B27098
Three gang mould• with cover• 1 packing unit = 162 piecesOrder-No. B27099
Three gang mould• made of white special plastic (Hakorit)• very low-wear• stiffned against bending and unbreakable• self-lubricated• easy cleaning because no cement or mortar
adheres• no rust possible• no much time necessary for cleaning• temperature for use max. +80°C• temperature for use min. -30°C• for simultaneous production of 3 test
specimens• dimensions: 40 x 40 x 160 mmOrder-No. B270940
Six gang mould• made of white special plastic (Hakorit)• very low-wear• stiffned against bending and unbreakable• self-lubricated• easy cleaning because no cement or mortar
adheres• no rust possible• no much time necessary for cleaning• temperature for use max. +80°C• temperature for use min. -30°C• for simultaneous production of 6 test
specimens• dimensions: 40 x 40 x 160 mmOrder-No. B270942
A
B
C
D
A
C
A
B
B
4
Mortar test
DIN EN 459-2 DIN EN 1015
Shrinkage measuring device • with digital gauge• for specimens 40x40x160 mm• for strength up to 0,5 N/mm²• measuring range 10 mm• resolution 0,001 mm• C lying executionOrder-No. B29081
• B standing executionOrder-No. B29102
Shrinkage measuring device • with analogues gauge• C lying executionOrder-No. B29083
• B standing executionOrder-No. B2910
Reference body COrder-No. B29084
Reference body BOrder-No. B29104
Measuring pins• form C, Type 1• 1 packing unit = 60 piecesOrder-No. B290850
• form C, Type 2• 1 packing unit = 60 piecesOrder-No. B290870
• form AB, Type 1• 1 packing unit = 60 piecesOrder-No. B290860
• form AB, Type 2• 1 packing unit = 60 piecesOrder-No. B290880
FORM+TEST Seidner & Co. GmbHPost box 1154 • D-88491 Riedlingenphone: +49 (0) 7371 9302-0 • fax: -99
www.formtest.desales@formtest.de
L180
.02E
• M
örte
lprü
fung
.indd
• 12
/201
3
A
B
C
1
Compression and bending testing machineMEGA 100-200-10 DM1-S●accuracy according to
DIN EN ISO 7500-1, class 1●forcompressionandflexure
strength tests according to EN 196, EN 1015, EN 13892-3 with options also acc. EN 12504-1 and EN 993-5
●with automatical load increase, control via digital controller DIGIMAXX® C-20 in closed loop system
Technical dates - compression frame●testloadmax.:200kN●workingpressuremax.:192.55bar●pistonstroke:50mm●upperplaten:40mm●lowerplaten:40mm●hardnessofplatens:58-62HRC>600HV●testchamberheight:50mm●cleardistancebetweencolumns:226mm●measuringrange:2.00...200kN●displayrange:0...200kN
Technicaldates-bending(flexure)frame●testloadmax.:10kN●workingpressuremax.:79,57bar●pistonstroke(ramtravel):50mm●testchamberheight:50mm●bendingrollerlength:50mm●bendingrollerØ:10mm●bendingrollerdistance:100mm●measuringrange:0.2...10kN●displayrange:0...10kN
●loadmeasuringbyoneelectronicloadcellforcompressionandoneforbending,built-infreeofshear
●voltage:3x400Volt,50Hz,1.5kW●weight:appr.300kg
DC
A
E
B
2
Technical dates - digital controller● LCD-screen-display,5numbers,16Bit
processortechnology
● resolution60,000Digits
● automaticzeropointcorrection
● programmablecalculationofthestrengthof30differentspecimensaswellasthecorrespondingstandardspeeds
● displayofthestrengthinN/mm²orMpa
● adjustabledisplayinkN,N,kg,kp,toorbar
● peakvaluememoryandresetkey
● codeprotectedcalibration/linearization
● serialinterfaceRS232torecallthepeakvalue
● memory
Options:● enlargement(higher)testchamber
● enlargement(bigger)compressionplates dimension110x110x30mm dimensionØ210x40mm dimension210x210x40mm
Asetofplaten40x40mmforbendingframe
Bbendingtablewithmoveablebendingrollerdistance30...250mm
CcompressiondeviceDV600AZ
DbendingdeviceBV10OM
EbuildingmaterialtestsoftwarePROTEUS
● transfersoftwareWinTrans
Available with following test loads:● forcompression: 100kN,200kN,300kN
● forbending: 10kN,20kN,30kN
PM
M 1
01.0
2E -
ME
GA
100-
200-
10D
M1-
S.in
dd -
01/
2014
• Te
chni
cal m
odifi
catio
ns re
serv
ed!
FORM+TEST Seidner & Co. GmbHPostbox1154•D-88491Riedlingenphone:+49(0)73719302-0•fax:-99
www.formtest.desales@formtest.de
1
A
D
C
B
Special-plastic-moulds for production of specimensmade of white special plastic(Hakorit)
• very low-wear • stiffned against bending and
unbreakable• self-lubricated• easy cleaning because no cement
or mortar adheres • no rust possible• no much time necessary for
cleaning• temperature for use max. +80°C• temperature for use min. -30°C
Three gang mould• for simultaneous production of 3 test
specimens• dimensions: 40 x 40 x 160 mmOrder-No. B270940
Six gang mould• for simultaneous production of 6 test
specimens• dimensions: 40 x 40 x 160 mmOrder-No. B270942
Three gang mould• for simultaneous production of 3 test
specimens• dimensions: 230 x 64 x 54 mmOrder-No. B270950
Triple cylinder mould• for simultaneous production of 3 test
specimens• dimensions: diameter: 50 mm height: 50 mmOrder-No. B16090
Triple cylinder mould• for simultaneous production of 3 test
specimens• dimensions: diameter: 36 mm height: 36 mmOrder-No. B16092
A
B
C
D
2
E
D
C
B
A
Special-plastic-moulds for production of specimens
Triple cube mould• for simultaneous production of 3 test
specimens• dimensions: 50 x 50 x 50 mmOrder-No. B1580
Double cube mould• for simultaneous production of 2 test
specimens• dimensions: 150 x 150 x 150 mmOrder-No. B1560
Triple cube mould• for simultaneous production of 3 test
specimens• dimensions: 150 x 150 x 150 mmOrder-No. B1562
Triple cube mould• for simultaneous production of 3 test
specimens• dimensions: 100 x 100 x 100 mmOrder-No. B1566 (without picture)
Test mould for square plates• dimensions: 600 x 600 x 100 mmOrder-No. B15268
Beam mould• dimensions: 600 x 150 x 150 mmOrder-No. B15248
Beam mould• dimensions: 900 x 150 x 150 mmOrder-No. B15244 (without picture)
Beam mould• dimensions: 700 x 150 x 150 mmOrder-No. B15246 (without picture)
Beam mould• dimensions: 540 x 150 x 150 mmOrder-No. B15249 (without picture)
FORM+TEST Seidner & Co. GmbHPost box 1154 • D-88491 Riedlingenphone: +49 (0) 7371 9302-0 • fax: -99
www.formtest.desales@formtest.de
L115
.02E
- S
pezi
al-K
unst
stof
f-For
men
.indd
• 01
/201
4
A
B
C
D
E
A
A A
B
C
D
E F
1
Construction repair
Crack measuring - ZTV-Ing.
Precision magnifier set• with battery operated LED lighting
equipment• changeable measuring scales with line-,
lattice-, circle scales• division: 0.1 resp. 0.5 mm• two (2) magnifier heads• with magnification 8- and 10x• stand magnifier• with magnification 40-, 50- and 60x• storage- and transport caseOrder-No. T0180
Precision magnifier• with LED lighting• magnification 10x• division: 0.1 mmOrder-No. T0110
Crack monitor• for straight surfaces• division: 1.0 mmOrder-No. T0280
Crack monitor• for straight surfaces• with stainless steel measuring points• division: 1.0 mmOrder-No. T0281
Crack displacement tester• for measuring and storage of crack changes• with installed thermo-hygrometer for
measuring and storage of temperature at same time
• execution optional with memory for: 16,000, 32,000 or 64,000 readings
Order-No. T0300
Standard of comparison for crack widths
• set each 15 pieces• crack-division:
0.05 – 0.1 – 0.15 – 0.2 – 0.25 – 0.3 – 0.35 – 0.4 – 0.45 – 0.5 – 0.55 – 0.6 – 0.65 – 0.7 – 0.75 – 0.8 – 0.85 – 0.9 – 0.95 – 1.0 – 1.05 – 1.1 – 1.15 – 1.2 – 1.3 – 1.4 – 1.6 – 1.8 – 2.0 – 2.5 – 3.0 – 3.5 mm
• photo comparison grid in black/white• with integrated surface temperature scaleOrder-No. T02011
A
B
C
D
E
F
A
A
A
B
C
C
2
Construction repair
Crack measuring
Camera - Microscope• for crack width documentation, -measuring
and -judgment• collapsible and turnable
TFT-colour display 3“• focussing equipment 10 mm until 30 mm • very good definition• integrated lighting over 8 white LED´s • data storage over MicroSD card• magnification 20...200x• magnification at 5 MegaPixel-resolution
until 500x• software for true to scale measurements of
cracks/spaces• resolution until 0.001 mm• dimensions 130 x 112 x 28 mm• weight approx. 175 gOrder-No. T0190
Extension measuring device• with digital gauge• control line made of INVAR-steel • 50 measuring pins Ø 10 mm• adhesive gage with 3 adhesive templates • robust transport case• measuring length 250 mm• resolution 0.01 mm• accuracy +/- 0.01 mm• length changing-measuring range +/- 5 mm• weight approx. 175 gOrder-No. T02696
Coating thickness
BAM–Coating thickness meter• on concrete / wood• acc. to ZTV-ING• with digital gaugeOrder-No. T0554
BAM–Coating thickness meter• as before but with analogues gauge(without picture)Order-No. T0552
A
B
C
A
B
C
C
D
3
Construction repair
Component moisture test
Electronic moisture testerRAPID
• non-destructive measuring of moisture in concrete and screed
• up to 15 – 30 mm depth• measuring range concrete: 0…6 %• measuring range flow screed: 0…9 %Order-No. T0980
Electronic moisture tester EFM II
• to measure cement bound* and anhydrite bound** material
• system „KRAFFT“• measuring range*: 1.12 … 6.5 %• measuring range**: 0.25 … 4.0 %Order-No. T0995
CM–moisture tester• moisture test acc. calcium carbide method• with analogues manometer• with electronic precision balance• with stop watch / timerOrder-No. T0840
CM–moisture tester• acc. ZTV-ING • moisture test acc. calcium carbide method • with analogues manometer• with electronic precision balance• with stop watch / timer• with additional stainless steel sieve Ø 100 mm, mesh 2.0 mm(without picture)Order-No. T0841
CM–moisture tester• moisture test acc. calcium carbide method • with digital manometer • with electronic precision balance• with stop watch / timerOrder-No. T0855
A
B
C
D
A
B
C
4
E
D
F
Construction repair
Component temperaturemeasuring
Electronic digital thermometer• for surface temperature measuring• with surface temperature probe• transport caseOrder-No. R0175
Infrared-thermometer• for non contacting measuring of fresh
concrete temperature• big LCD display • height of numbers 8 mm• measuring range -35 ... +365°C• resolution 0.1°COrder-No. R0201
Concrete-digital thermometer• with LCD-digital display• height of numbers 5 mm• probe made of stainless steel• with protective cover and clip• measuring range -50 ... +200 °C• resolution 0.1 °C• length 125 mmOrder-No. R0110
Concrete-digital thermometer like R0110 but with• length 300 mmOrder-No. R0112
Concrete-thermometer• big LCD-display• height of numbers 15 mm• functions test - Max - Min - Hold• stick-in probe 100 mm• with cable 100 cm• measuring range -40 ... +200 °C• resolution 0.1°COrder-No. R0114
Air humidity-, Air temperature- andComponent temperature measuring
Electronic Thermo-Hygrometerwith laser pyrometer
• with dewpoint calculation• with non contacting surface temperature
measuringOrder-No. R0545
A
B
C
D
E
F
A
B
5
C
D
Construction repair
Air humidity- and Air temperature measuring
Electronic Thermo-Hygrometer
• with dewpoint calculationOrder-No. R0540
Electronic Thermo-Hygrograph
• for fully automatic registration of temperature and humidity with internal measuring sensors
• stable plastic housing• big LCD-display 90 x 64 mm• data memory for 3,200,000 values• USB-data interface for data transfer for
graphic and numeric presentation and evaluation
Order-No. R0920
Electronic Thermo-Hygrometer
• parameter: temperatur/humidity• measuring range: -20...+60°C / 0...99 %rF• resolution: 0.1°C / 0.1% rF• accuracy: +/-0.5°C / +/-3% (20...80%)
otherwise +/-4%• battery lifetime: approx. 48 hours• dimensions (LxWxH): 146 x 54 x 34 mm• weight: 138 gOrder-No. R0555
Air speeds
Anemometer• parameter: flow• measuring range: 0.4...+25 m/s• resolution: 0.01 m/s• accuracy: +/-3.5% +0,20 m/s of end value• battery lifetime: approx. 100 hours• dimensions (LxWxH): 165 x 54 x 34 mm• weight: 82 gOrder-No. R0600
A
B
D
C
A
B
6
C
D
Construction repair
Environment measuring equipments
Sound level meter• parameter: sound• measuring range: 40...130 dB• resolution: 0.1 dB• accuracy: 3.0 dB• battery lifetime: typically 50 hours in
continous operation• dimensions (LxWxH): 157 x 54 x 34 mm• weight: 131 gOrder-No. R0601
Light measuring equipment• parameter: light power• measuring range: 0.0...40,000 lx• resolution: 0,1 lx / 0.1 fc• accuracy: +/-5%• battery lifetime: typically 24 h of continous
operation• dimensions (LxWxH): 157 x 54 x 34 mm• weight: 138 gOrder-No. R0602
Gross density / Weighing
Electronic platform balance • with separate display• height of numbers: 25 mm• IP 65• with data interface RS 232• for operation by power supply unit or by
storage battery (option)• weighing platform made of stainless steel
310 x 300 mm• weighing capacity 0 ... 30 / 60 kg• resolution 10 / 20 g• with supply unit 230 VoltOrder-No. O03510
Electronic compact balance • with integrated display• height of numbers: 25 mm• with data interface RS 232• for operation by power supply unit or by
storage battery (option)• underfloor weighing unit• weighing platform made of stainless steel
340 x 240 mm• weighing capacity 0 ... 30 kg• resolution 1.0 g• with supply unit 230 VoltOrder-No. O0436
A
B
C
D
A
B
C
D
7
E F
Construction repair
Mortar test - ZTV-Ing.
Air entrainment meter• for testing of air content in fresh mortar• incl. washing bottle 1000 ml • content 1 ltr.Order-No. B2030
Extension collar• for air entrainment meter B2030Order-No. B2031
Pot 1 Litre• for determination of gross densityOrder-No. B2030-18
Haegermann-flow table• for flow tests• manually operated, without counter • complete with stainless steel plate Ø 300 mm• funnel Ø 70/100 mm, height 60 mm,
material thickness 2 mm• extension collar and hand tamperOrder-No. B29015
Haegermann-flow tableas before, but with:
• manually operated, with counter (without picture)Order-No. B29025
Three gang mould• light execution• surface yellow passivated• dimensions: 40 x 40 x 160 mmOrder-No. B2709
Three gang mould• made of white special plastic (Hakorit)• very low-wear• stiffned against bending and unbreakable• self-lubricated• easy cleaning because no cement or mortar
adheres• no rust possible• no much time necessary for cleaning• temperature for use max. +80°C• temperature for use min. -30°C• for simultaneous production of 3 test
specimens• dimensions: 40 x 40 x 160 mmOrder-No. B270940
A
C
E
D
B
F
A
B
C
C
8
D
Construction repair
Non-destructive compression strength test
Concrete test hammer• Classic-SM-executionOrder-No. B14112
Test anvil • for function control of concrete test hammerOrder-No. B141142
Bond strength test
Bond strength testerConfiTEST 12
• to test the surface- and bond strength of concrete, mortar, coatings
• acc. to ZTV-SIB (1990), ZTV-ING (2003) BEB-Merkblatt, DAfStb-Rili, DIN 1048-part 2
• load increase by smooth acting manual drive• load measurement by digital precision
manometerOrder-No. B3060
Concrete cover test
Set of test magnets• for evaluation resp. pre-investigation of
concrete covers• 4 different test magnets• transport case• evaluating tableOrder-No. B1470
A
B
C
D
FORM+TEST Seidner & Co. GmbHPostfach 1154 • D-88491 Riedlingenphone: +49 (0) 7371 9302-0 • fax: -99
www.formtest.desales@formtest.de
L162
.02E
• B
auin
stan
dset
zung
.indd
• 11
/201
3
top related