formtracer sv-c3100 / sv-c4100 - mitutoyo · k-16 k formtracer sv-c3100 / sv-c4100 series 525 —...
Post on 11-May-2018
405 Views
Preview:
TRANSCRIPT
K-16
K
Formtracer SV-C3100 / SV-C4100SERIES 525 — Surface Roughness / Contour Measuring System
FEATURES•Dramaticallyincreaseddrivespeed(Xaxis:
80 mm/s, Z2 axis column: 20mm/s) further reduces total measurement time.
•Mitutoyohasadoptedhighlyrigidceramicguides, combining small secular change and remarkable resistance to abrasion, to maintain the traverse linearity specification for an extended period of time.
•Thedriveunit(Xaxis)andcolumn(Z2axis)are equipped with highly accurate linear encoders (ABS type on the Z2 axis). This improves reproducibility of continuous automatic measurement of small holes in the vertical direction and repeated measurement of parts which are difficult to position.
Technical Data: CommonBase size (W x H): 600 x 450mm or 1000 x 450mmBase material: GraniteMass
Main unit: 140kg (S4), 150kg (H4), 220kg (W4) 140kg (S8), 150kg (H8), 220kg (W8)
Controller Unit: 14kg Remote Control Box: 0.9kgPower supply: 100 – 240VAC ±10%, 50/60HzPower consumption: 400W (main unit only)
Technical Data: Contour MeasurementX axis Measuring range: 100mm or 200mm Resolution: 0.05µm Scale: Reflective-type linear encoder Drive speed: 0 - 80mm/s and manual Measuring speed: 0.02 - 5mm/s Measuring direction: Forward/backward Traverse linearity: 0.8µm / 100mm, 2µm / 200mm *with the X axis in horizontal orientation Linear displacement: ±(1+0.01L)µm (SV-C3100S4, H4, W4)
accuracy (at 20°C) ±(0.8+0.01L)µm (SV-C4100S4, H4, W4) ±(1+0.02L)µm (SV-C3100S8, H8, W8) ±(0.8+0.02L)µm (SV-C4100S8, H8, W8)
* L = Drive length (mm) Inclining range: ±45° (with X-axis inclination unit)Z2 axis (column) Vertical travel: 300mm or 500mm Resolution: 1µm Scale: ABSOLUTE linear encoder Drive speed: 0 - 20mm/s and manualZ1 axis (detector unit) Measuring range: ±25mm Resolution: 0.2µm (SV-C3100),
0.05µm (SV-C4100) Scale: Linear encoder (SV-C3100),
laser hologage (SV-C4100) Linear displacement: ±(2+I4HI/100)µm (SV-C3100)
accuracy (at 20°C) ±(0.8+I0.5HI/25)µm (SV-C4100) *H: Measurement height from the
horizontal position (mm) Stylus up/down operation: Arc movement Face of stylus: Upward/downward Measuring force: 30mN Traceable angle: Ascent: 77°, descent: 87°
(using the standard stylus provided and depending on the surface roughness)
Stylus tip Radius: 25µm, carbide tip
Technical Data: Surface Roughness MeasurementX1 axis Measuring range: 100mm or 200mm Resolution: 0.05µm Scale: Linear encoder Drive speed: 0 - 80mm/s and manual Traverse direction: Backward Traverse linearity: (0.05+1L/1000)µm (S4, H4, W4 types)
0.5µm/200mm (S8, H8, W8 types)Z2 axis (column) Vertical travel: 300mm or 500mm Resolution: 1µm Scale: ABSOLUTE linear encoder Drive speed: 0 - 20mm/s and manualDetector Range / resolution: 800µm / 0.01µm, 80µm / 0.001µm,
8µm / 0.0001µm (up to 2400µm with an optional stylus)
Measuring force: 4mN or 0.75mN (low force type) Stylus tip: Diamond, 90º / 5µmR
(60º / 2µmR: low force type) Type: Differential inductance
Using Rotary Table q1Using Y-axis Table
Using Rotary Table q2
Automatic Measurement•Awiderangeofoptionalperipheralsare
available for use with CNC models for automatic measurement.
SV-C3100S4 with personal computer system and software
Surface Roughness Measurement
•Traverselinearity:±(0.05+0.001L)µm* Designed to handle workpieces calling for high accuracy. *S4, H4, W4 types, L = Drive length (mm)
•CompliantwithJIS'82/'94/'01,ISO,ANSI,DIN, VDA, and other international surface roughness standards.
•Equippedasstandardwithahighaccuracydetector (0.75mN / 4mN measuring force) providing a resolution down to 0.0001µm.
Contour Drive Measurement
•Xaxisaccuracy:±(0.8+0.01L)µm* Z1-axis accuracy: ±(0.8+I0.5HI/25)µm*
Designed to handle workpieces calling for high accuracy.* SV-C4100S4, H4, W4 types, L = Drive length, H = Measurement height (mm)
•ThecontourdriveunitofSV-C4100series is equipped with a Laser Hologage detector giving excellent narrow/wide range accuracy and resolution in the Z1-axis.
(See page K-34 for more details.)
K-17
K
SPECIFICATIONSModel No. SV-C3100S4 SV-C3100S4 SV-C3100H4 SV-C3100H4 SV-C3100W4 SV-C3100W4Order No. (mm) 525-421*-1 525-421*-2 525-422*-1 525-422*-2 525-423*-1 525-423*-2Order No. (inch) 525-431*-1 525-431*-2 525-432*-1 525-432*-2 525-433*-1 525-433*-2
A variety of models available for measuring requirements
SV-C3100S4 / SV-C4100S4Traverse range: 100mmVertical travel: 300mmBase size (W x D): 600 x 450mmBase material: Granite
SV-C3100H4 / SV-C4100H4Traverse range: 100mmVertical travel: 500mmBase size (W x D): 600 x 450mmBase material: Granite
SV-C3100W4 / SV-C4100W4Traverse range: 100mmVertical travel: 500mmBase size (W x D): 1000 x 450mmBase material: Granite
Model No. SV-C3100S8 SV-C3100S8 SV-C3100H8 SV-C3100H8 SV-C3100W8 SV-C3100W8Order No. (mm) 525-426*-1 525-426*-2 525-427*-1 525-427*-2 525-428*-1 525-428*-2Order No. (inch) 525-436*-1 525-436*-2 525-437*-1 525-437*-2 525-438*-1 525-438*-2
SV-C3100S8 / SV-C4100S8Traverse range: 200mmVertical travel: 300mmBase size (W x D): 600 x 450mmBase material: Granite
SV-C3100H8 / SV-C4100H8Traverse range: 200mmVertical travel: 500mmBase size (W x D): 600 x 450mmBase material: Granite
SV-C3100W8 / SV-C4100W8Traverse range: 200mmVertical travel: 500mmBase size (W x D): 1000 x 450mmBase material: Granite
Refer to the Formtracer SV-C3100 / 4100 Series leaflet (E4304) for more details.
Surface Roughness Measurement Screen
Optional SoftwareFORMTRACEPAK Allows control of the optional motor-driven Y-axis table and rotary table for efficient measurement automation. Contour evaluation can be performed using analysis of level differences, angle, pitch, area and other characteristics based on surface roughness data. An original inspection certificate can be created by setting the print format to selected requirements.
Contour Measurement Screen
Model No. SV-C4100S4 SV-C4100S4 SV-C4100H4 SV-C4100H4 SV-C4100W4 SV-C4100W4Order No. (mm) 525-461*-1 525-461*-2 525-462*-1 525-462*-2 525-463*-1 525-463*-2Order No. (inch) 525-471*-1 525-471*-2 525-472*-1 525-472*-2 525-473*-1 525-473*-2X1-axis measuring range 100mm 100mm 100mm 100mm 100mm 100mmDetector measuring force 0.75mN 4mN 0.75mN 4mN 0.75mN 4mNVertical travel 300mm power column 500mm power column 500mm power columnGranite base size (WxD) 600 x 450mm 600 x 450mm 1000 x 450mmDimensions (main unit, WxDxH) 996 x 575 x 966mm 996 x 575 x 1166mm 1396 x 575 x 1176mmMass (main unit) 140kg 150kg 220kg
Model No. SV-C4100S8 SV-C4100S8 SV-C4100H8 SV-C4100H8 SV-C4100W8 SV-C4100W8Order No. (mm) 525-466*-1 525-466*-2 525-467*-1 525-467*-2 525-468*-1 525-468*-2Order No. (inch) 525-476*-1 525-476*-2 525-477*-1 525-477*-2 525-478*-1 525-478*-2X1-axis measuring range 200mm 200mm 200mm 200mm 200mm 200mmDetector measuring force 0.75mN 4mN 0.75mN 4mN 0.75mN 4mNVertical travel 300mm power column 500mm power column 500mm power columnGranite base size (WxD) 600 x 450mm 600 x 450mm 1000 x 450mmDimensions (main unit, WxDxH) 1006 x 575 x 966mm 1006 x 575 x 1166mm 1406 x 575 x 1176mmMass (main unit) 140kg 150kg 220kg
* To denote your AC power cable add the following suffixes to the order No.: ”mm” type: A for UL/CSA, C for JIS (for Taiwan), D for CEE, E for BS, DC for China, K for EK “inch” type: A for UL/CSA, D for CEE, E for BS, DC for China, No suffix is requied for JIS/100V (for Taiwan)
K-18
K
Formtracer Extreme SV-C3000CNC / SV-C4000CNCSERIES 525 — Surface Roughness/Form Measuring Instrument
Technical Data: CommonBase size (W x D): 750 x 600mmBase material: GraniteMass: 240kg, 250kg (high column type)Power supply: 100 – 240VAC ±10%, 50/60HzPower consumption: 500W (main unit only)
Technical Data: Contour MeasurementX1-axis Measuring range: 200mm Resolution: 0.05µm Measurement method: Reflective-type linear encoder Drive speed: 200mm/s (max., CNC) 0 - 60mm/s (joystick) Measuring speed: 0.02 - 2mm/s Measuring direction: Forward/backward Traverse linearity: 2µm/200mm *with the X axis in horizontal orientation Linear displacement accuracy (at 20°C):
±(1+4L/200)µm ±(0.8+4L/200)µm
Inclination angle: -45° to +10° Resolution: 0.000225° Rotating speed: 1rpmZ2-axis (column) Vertical travel: 300mm or 500mm Resolution: 0.05µm Measurement method: Reflective-type linear encoder Drive speed: 200mm/s (max., CNC) 0 - 60mm/s (joystick)Z1-axis (detector unit) Measuring range: ±25mm Resolution: 0.2µm (SV-C3000CNC),
0.05µm (SV-C4000CNC) Measurement method: Linear encoder (SV-C3000CNC),
laser hologage (SV-C4000CNC) Linear displacement: ±(2+|4H|/100)µm (SV-C3000CNC)
accuracy (at 20°C) ± (0.8+I0.5HI/25)µm (SV-C4000CNC) *H: Measurement height from the horizontal
position (mm) Stylus up/down operation: Arc movement Face of stylus: Downward Measuring force: 30mN Traceable angle: Ascent: 70°, descent: 70°
(using the standard stylus provided and depending on the surface roughness)
Stylus tip Radius: 25µm, carbide tip
Technical Data: Surface Roughness MeasurementX1-axis Measuring range: 200mm Resolution: 0.05µm Measurement method: Reflective-type linear encoder Drive speed: 200mm/s (max., CNC) 0 - 60mm/s (joystick) Measuring speed: 0.02 - 2mm/s Traverse linearity: 0.5µm / 200mmα-axis Inclination angle: -45° to +10° Resolution: 0.000225° Rotating speed: 1rpmZ2-axis (column) Vertical travel: 300mm or 500mm Resolution: 0.05µm Measurement method: Reflective-type linear encoder Drive speed: 200mm/s (max., CNC) 0 - 60mm/s (joystick)Detector (optional) Range / resolution: 800µm / 0.01µm, 80µm / 0.001µm,
8µm / 0.0001µm (up to 2400µm with an optional stylus)
Measuring force: 4mN or 0.75mN (low force type) Stylus tip: Diamond, 90º / 5µmR
(60º / 2µmR: low force type) Detecting method: Differential inductance
FEATURES•High-accuracyCNCSurfaceRoughness/
Form Measuring Instrument that allows measurement of surface roughness and form/contour with one unit.
•Eachaxishasthemaximumdrivespeedof 200mm/s, which permits high-speed positioning that may result in a large increase in the throughput of multiple-profile/multiple-workpiece measurement tasks.
•Formodelswiththeα axis, it is possible to perform continuous measurement over horizontal and inclined surfaces by power-tilting the detector unit.
•FormodelswiththeY-axistable,itispossible to expand the measuring range for multiple workpieces, etc., through positioning in the Y-axis direction.
•ThecontourdriveunitofSV-C4000CNCseries is equipped with a Laser Hologage detector giving excellent narrow/wide range accuracy and resolution in the Z1-axis.
•Enablesinclinedplanemeasurementsthrough 2-axis simultaneous control in the X- and Y-directions.
•Whenthedetectorforform/contourmeasurement is replaced with that for surface roughness measurement, or vice versa, it is a simple, one-touch replacement without re-routing of the connecting cables.
•SincetheZ1-axisdetectorincorporatesananti-collision safety device, the detector unit will automatically stop even if its main body collides with a workpiece or jig
•Suppliedwithaneasy-to-operateRemoteBox, on which the user can make any movement by selecting the required axis using the two joysticks. The current axis selection is easily identified by the icon on the key top.
•CommunicationwiththeDataProcessing/Analysis section is via USB.
SV-3000CNC with personal computer system and software
Surface roughness drive unit Contour drive unit
K-19
Z2
X-axis displacement range
Y axis
K
SPECIFICATIONSModel No. SV-C3000CNC SV-C3000CNC SV-C3000CNC SV-C3000CNCOrder No. (100V - 120V) 525-521-1 525-522-1 525-523-1 525-524-1Order No. (200V - 240V) 525-521-2 525-522-2 525-523-2 525-524-2X1-axis measuring range 200mm 200mm 200mm 200mmZ2-axis vertical travel 300mm 300mm 300mm 300mmY-axis table unit — — Installed Installedα-axis unit — Installed — InstalledGranite base size (WxD) 750 x 600mm 750 x 600mm 750 x 600mm 750 x 600mmDimensions (main unit, WxDxH) 800 x 651 x 1000mm 800 x 651 x 1000mm 800 x 651 x 1000mm 800 x 651 x 1000mmMass (main unit) 240kg 240kg 240kg 240kg
Model No. SV-C3000CNC SV-C3000CNC SV-C3000CNC SV-C3000CNCOrder No. (100V - 120V) 525-541-1 525-542-1 525-543-1 525-544-1Order No. (200V - 240V) 525-541-2 525-542-2 525-543-2 525-544-2X1-axis measuring range 200mm 200mm 200mm 200mmZ2-axis vertical travel 500mm 500mm 500mm 500mmY-axis table unit — — Installed Installedα-axis unit — Installed — InstalledGranite base size (WxD) 750 x 600mm 750 x 600mm 750 x 600mm 750 x 600mmDimensions (main unit, WxDxH) 800 x 651 x 1200mm 800 x 651 x 1200mm 800 x 651 x 1200mm 800 x 651 x 1200mmMass (main unit) 250kg 250kg 250kg 250kg
Model No. SV-C4000CNC SV-C4000CNC SV-C4000CNC SV-C4000CNCOrder No. (100V - 120V) 525-621-1 525-622-1 525-623-1 525-624-1Order No. (200V - 240V) 525-621-2 525-622-2 525-623-2 525-624-2X1-axis measuring range 200mm 200mm 200mm 200mmZ2-axis vertical travel 300mm 300mm 300mm 300mmY-axis table unit — — Installed Installedα-axis unit — Installed — InstalledGranite base size (WxD) 750 x 600mm 750 x 600mm 750 x 600mm 750 x 600mmDimensions (main unit, WxDxH) 800 x 651 x 1000mm 800 x 651 x 1000mm 800 x 651 x 1000mm 800 x 651 x 1000mmMass (main unit) 240kg 240kg 240kg 240kg
Model No. SV-C4000CNC SV-C4000CNC SV-C4000CNC SV-C4000CNCOrder No. (100V - 120V) 525-641-1 525-642-1 525-643-1 525-644-1Order No. (200V - 240V) 525-641-2 525-642-2 525-643-2 525-644-2X1-axis measuring range 200mm 200mm 200mm 200mmZ2-axis vertical travel 500mm 500mm 500mm 500mmY-axis table unit — — Installed Installedα-axis unit — Installed — InstalledGranite base size (WxD) 750 x 600mm 750 x 600mm 750 x 600mm 750 x 600mmDimensions (main unit, WxDxH) 800 x 651 x 1200mm 800 x 651 x 1200mm 800 x 651 x 1200mm 800 x 651 x 1200mmMass (main unit) 250kg 250kg 250kg 250kg
Refer to the CNC Form Measuring Instrument Series leaflet (E4284) for more details.
Optional AccessoriesVibration insulating standVibration insulating mechanism: Diaphragm air spring Natural frequency : 2.5 - 3.5HzDamping mechanism: OrificeLeveling mechanism: Automatic control with mechanical valvesAir supply pressure: 0.4MpaAllowable loading capacity: 350kgDimensions (W x D x H): 1000 x 895 x 715mmMass: 315kg
Y-axis table unitMeasuring range: 200mmMinimum reading : 0.05µmScale unit: Reflective-type Linear Encoder Drive speed: 200mm/s (max., CNC) 0 - 60mm/s (joystick)Maximum loading capacity: 20 kgTraverse linearity 0.5µm / 200mmLinear displacement accuracy (at 20°C): ± (2+2L/100)µm, contour mode L: Dimension between two measured points (mm)Table size: 200 x 200mmDimensions (W x D x H): 320 x 646 x 105mmMass: 35kg
Optional SoftwareFORMTRACEPAK V5Enables control of the optional motor-driven Y-axis table and rotary table for realizing efficient measurement automation. You can also perform contour evaluation that allows free analysis of level differences, angle, pitch, area and other characteristics based on surface roughness data. In addition, you can create an original inspection certificate by setting the print format to suit your particular requirements.
K-20
Technical Data:X1-axis Measuring range: 100mm Resolution: 0.05µm Drive speed: 0 - 80mm/s and manual Measuring speed: 0.02, 0.05, 0.1, 0.2mm/s (in surface roughness measurement)
0.02, 0.05, 0.1, 0.2, 0.5, 1, 2mm/s (In contour measurement) Measuring direction: Forward / backward Traverse linearity: 0.2µm/100mm (0.4µm/100mm: at
the extended detector position) *with the X axis in horizontal orientation
Linear displacement accuracy (20°C): ±(0.8+0.01L)µm L = Drive length (mm)
Inclining range: ±45ºZ1-axis Measuring range: 5mm Resolution: 80nm (5mm range) 8nm (0.5mm range) 0.8nm (0.05mm range) Linear displacement accuracy (20°C): ±(1.5+I2HI/100)µm
H = Measurement height from the horizontal position (mm) Measuring force: 0.75mN Traceable angle: Ascent: 65°, Descent: 65°
(using the standard chisel-cut stylus and depending on the surface roughness) Stylus tip (standard): Tip angle: 60º, Tip radius: 2µm,
Diamond tip Stylus tip (cone): Tip angle: 30º, Tip radius: 25µm,
Sapphire tip Face of stylus: DownwardZ2-axis (column) Column travel: 300mm Resolution: 1µm Drive speed: 0 - 20mm/s and manual
FEATURES•Thedriveunit(X-axis)andcolumn(Z2-axis)
are equipped with high-accuracy linear scales (ABS type) enabling fully automatic measurement combining vertical and horizontal movement. This improves reproducibility of continuous automatic measurement of small holes in the vertical direction and repeated measurement of parts which are difficult to position.
•Thedetectorunitcanbeextendedtoavoid interference between the drive unit and workpiece. All detector and drive unit cables are housed inside the main unit to eliminate any risk of abrasion and guarantee trouble free, high-speed operation.
•MeasuringrangeintheZ1-axis(height)direction is dramatically increased from 5mm to 50mm when contour detector units 3000*, or 4000*, are specified. (Both are factory-set options.)
•Driveunit(X-axis)tiltingfunctionpowerfully supports measurements on inclined planes and for heavy workpieces that are not easily moved.
CS-3200S4 with personal computer system and software
Formtracer CS-3200SERIES 525 — Surface Roughness / Contour Measuring System
Technical Data: CommonBase size (W x D): 600 x 450mmBase material: GraniteDimension (W x D x H): 756 x 482 x 966mm (main unit)Mass: 140kg (main unit)Power supply: 100 – 240VAC ±10%, 50/60HzPower consumption: 400W (main unit only)
Outside diameter 1
Outside diameter 2
Inside diameter
Continuous measurement example (Outside diameter 1→Outside diameter 2→Inside diameter)
*: Styli for CS-3200 cannot be used. Styli for contour measuring instruments CV-3100/4100 series can be used.Supports contour measurement only.
Measurement element
Positioning element
With contour detector unit 3000 equipped•Dramaticallyincreaseddrivespeed(X-axis:
80mm/s, Z2-axis: 20mm/s) further reduces total measurement time. Small holes can be efficiently measured using the fine-feed knobs on the X- and Z2-axes.
This machine incorporates a startup system (relocation detection system), which disables operation when an unexpected vibration is applied or the machine is relocated. Be sure to contact your nearest Mitutoyo office prior to relocating this machine after initial installation. Refer to page IX for details.
Main UnitStartup System
K
K-21
Refer to the Formtracer CS-3200 leaflet (E4327) for more details.
SPECIFICATIONSModel No. CS-3200S4Order No. (mm) 525-401*Order No. (inch) 525-411*X1-axis measuring range 100mmZ2-axis vertical travel 300mmY-axis table unit Optiona-axis unit Installed
* To denote your AC power cable add the following suffixes to the order No.: ”mm” type: A for UL/CSA, C for JIS (for Taiwan), D for CEE, E for BS, DC for China, K for EK “inch” type: A for UL/CSA, D for CEE, E for BS, DC for China, No suffix is requied for JIS/100V (for Taiwan)
Optional SoftwareFORMTRACEPAK-6000
Stylus
Measuring instrument control
Contour analysis
Surface roughness analysis
Design data creation (CAD file import)
Contour verification
Inspection certificate creation
30°
ø3
66.5591
3.2
ø4810
(6.5)
60°0.6 (6.5)59
3.2
ø4
9ø1.2
10 0.4
66.1
24.84
60°
ø3
ø1.2ø4
67.5
3.2
ø4
59
(8)10
18 21 (6.5)
60°
23
3.2
ø4
21
1 5966.5
ø1.2
ø3
(6.5)
136.5
ø3
ø1.2
1
3.2ø4
12.5
129
14.5
40°
(6.5)
No.12AAD554: Standard stylus (Standard accessory)For contour/surface roughness measurement
No.12AAD556: Small hole stylusFor contour/surface roughness measurement
No.12AAD552: Cone stylus (Standard accessory)For contour measurement
No.12AAD558: Eccentric type stylusFor contour/surface roughness measurement
No.12AAD560: Deep groove stylusFor contour/surface roughness measurement
No.12AAD562: 2x-long stylus*1
For contour/surface roughness measurement
ø1.2
66.5
ø3
1 59
60°ø4
3.210 8
(6.5)
Radius of tip curvature: 25µmTip material: Sapphire
Radius of tip curvature: 2µmTip material: Diamond
Radius of tip curvature: 2µmTip material: Diamond
Radius of tip curvature: 2µmTip material: Diamond
Radius of tip curvature: 5µmTip material: Diamond
Radius of tip curvature: 2µmTip material: Diamond
*1: Measuring force is 4mN and the Z1 measuring range and resolution is double that of the standard stylus.
K
K-22
Formtracer Extreme CS-H4000CNCSERIES 525 — CNC Form Measuring Instruments
Technical Data:X1-axis Measuring range: 100mm Resolution: 0.00625µm Measurement method: Laser Holoscale Drive speed: Max. 40mm/s (in CNC mode)
0 - 40mm/s (in joystick control mode) Measuring speed: 0.02 - 0.2mm/s (surface roughness)
0.02 - 2mm/s (form/contour) Measuring direction: Forward / backward direction Traverse linearity: (0.05+0.0003L)µm Linear displacement accuracy (20°C): ±(0.16+0.001L)µm
L = Measured length (mm)Z1-axis Measuring range: 12mm Resolution: 0.001µm Stylus up/down: Arc movement Measurement method: Laser Holoscale Linear displacement accuracy (20°C): ±(0.07+I0.02HI)µm
H = Measured height (mm) Measuring force: 4mN Traceable angle: 60° for ascent, 60° for descent
(Depending on the workpiece surface condition) Stylus tip: Radius: 5µm, angle: 40°, diamond
(ball stylus) (Radius: 0.25mm, sapphire) Face of stylus: DownwardZ2-axis (column unit) Traverse range: 300mm Resolution: 0.05µm Measurement method: Reflective-type linear encoder Drive speed: Max. 200mm/s (in CNC mode)
0 - 50mm/s (in joystick control mode) Base size (W x D): 600 x 550mm Base material: GraniteY-axis* Measuring range 100mm Resolution 0.05µm Drive speed Max.80mm/s (in CNC mode) 0~50mm/s (in joystick control mode) Max. table loading 50kg Traverse linearity 1.0µm/100mm Positioning precision ±1µm *Only for 525-753, 525-754 For positioning only.Dimension (W x D x H): 600 x 570 x 992mm (main unit)Mass: 190kg (main unit)
FEATURES•High-accuracystylustypeCNCSurface
Measuring Instrument that allows simultaneous measurement of surface roughness and form/contour.
•TheX1-andZ2-axeshavemaximumdrive speeds of 40mm/s and 200mm/s, respectively. This permits high-speed positioning that may result in a large increase in the throughput of multiple-profile / multiple-workpiece measurement tasks.
•AMitutoyoLaserHoloscaleisincorporatedin the X1- and Z1-axes so that high resolution (X1-axis: 6.25nm, Z1-axis: 1nm) is achieved and batch measurement of form/contour and surface roughness can be made.
•Theactivecontrolmethodisemployedforthe Z1-axis detector to implement a wide-range measurement capability wherein the variation in dynamic measuring force is restricted.
•SincetheZ1-axisdetectorincorporatesananti-collision safety device, the detector unit will automatically stop even if its main body collides with a workpiece or jig.
•FormodelswiththeY-axistable,itispossible to expand the measuring range for multiple workpieces, etc., through positioning in the Y-axis direction.
•Suppliedwiththeeasy-to-operateRemoteBox, on which the user can make any movement by selecting the required axis using the two joysticks. The current axis selection is easily identified by the icon on the key top.
•UsesUSBforcommunicatingwiththeDataProcessing / Analysis Unit (optional).
Remote box Wide range detector employing active control technology
CS-H4000CNC with personal computer system and software
K
K-23
ASLPAKAspherical lens analysis program
107
65.95
ø1.2
(31.5)
35.9540º
74.51
ø6
12.5
(6.5
)
ø4
ø1.2
(31.5)
65.9535.95
74.51107
ø6
12.7
5
(6.8
)
ø4
ø0.5mm ball
15
35.9565.95
ø4ø6
1.6
0.4
ø1.2
(1.1
)
74.5 (31.5)0.6106.6
6
0.6
40ºAA
10
ø4ø6
1.2
0.6ø0
.6
(1.1
)
0.4
40º
74.5 (31.5)0.4106.4
35.9565.95
6
AAø4ø6
12.5ø6 (6.5
)
40˚35.95
ø1.2
65.95
74.5 (31.5)3109
16
12AAJ037: Standard-length stylus (tip radius: 5µm)(Standard accessory)
12AAD544: Standard-length ball stylus(Standard accessory)
12AAD651: Standard-length stylus for small hole (tip radius: 5µm)
12AAD652: Standard-length stylus for extra-small hole (tip radius: 5µm)
12AAD653: Standard-length eccentric stylus (tip radius: 5µm)
Detector Nosepiece
Unit: mm
SPECIFICATIONSModel No. CS-H4000CNC CS-H4000CNCOrder No. (mm) 525-751* 525-753*Order No. (inch) 525-752* 525-754*X1-axis measuring range 200mm 200mmZ2-axis vertical travel 300mm 300mmY-axis table unit — Installed
* To denote your AC power cable add the following suffixes to the order No.: A for UL/CSA, D for CEE, E for BS, DC for China, K for EK, No suffix is required for JIS/100V
Stylus
Optional SoftwareFORMTRACEPAK Enables control of the optional motor-driven Y-axis table and rotary table for realizing efficient measurement automation. You can also perform contour evaluation that allows free analysis of level differences, angle, pitch, area and other characteristics based on surface roughness data. In addition, you can create an original inspection certificate by setting the print format to suit your particular requirements.
K
K-24
K
Formtracer Extreme CS-5000CNC / CS-H5000CNCSERIES 525 — CNC Form Measuring Instruments
Technical Data:X1-axis Measuring range: 200mm Resolution: 0.00625µm Measurement method: Laser Holoscale Drive speed: Max. 40mm/s (in CNC mode)
0 - 40mm/s (in joystick control mode) Measuring speed: 0.02 - 0.2mm/s (surface roughness)
0.02 - 2mm/s (form/contour) Measuring direction: Forward / backward direction Traverse linearity: (0.1+0.0015L)µm with standard stylus
(0.2+0.0015L)µm with 2X-long stylus Traverse linearity: (0.05+0.0003L)µm with standard stylus
(0.1+0.0015L)µm with 2X-long stylus (CS-H5000CNC) Linear displacement accuracy (20°C): ±(0.3+0.002L)µm
Linear displacement accuracy (20°C): ±(0.16+0.001L)µm L = Measured length (mm)
Z1-axis Measuring range: 12mm (with standard stylus)
24mm (with 2X-long stylus) Resolution: 0.004µm(with standard stylus) 0.008µm(with 2X-long stylus) 0.001µm (with standard stylus) (CS-H500CNC)
0.002µm (with 2X-long stylus) (CS-H500CNC) Stylus up/down: Arc movement Measurement method: Laser Holoscale Linear displacement accuracy (20°C): ±(0.3+I0.02HI)µm
Linear displacement accuracy (20°C): ±(0.07+I0.02HI)µm H = Measured height (mm)
Measuring force: 4mN (with standard stylus) 0.75mN (with 2X-long stylus)
Traceable angle: 60° for ascent, 60° for descent(Depending on the workpiece surface condition)
Stylus tip: See the K-25 page Face of stylus: DownwardZ2-axis (column unit) Traverse range: 300mm or 500mm *CS-H5000CNC : 300mm only. Resolution: 0.05µm Measurement method: Reflective-type linear encoder Drive speed: Max. 200mm/s (in CNC mode)
0 - 50mm/s (in joystick control mode) Base size (W x D): 750 x 600mm Base material: GraniteY-axis* Measuring range 200mm Resolution 0.05µm Drive speed Max.200mm/s (in CNC mode) 0~50mm/s (in joystick control mode) Max.workpiece load 20kg Traverse linearity 0.5µm/200mm Linear displacement accuracy (20ºC) ±(2+2L/100)µm L = Length between arbitrary two point (mm)
Dimension (W x D x H): 800 x 620 x 1000mm (800 x 620 x 1200mm: high column type)
Mass: 240kg (250kg: high column type)*Data in red are for CS-H5000CNC
FEATURES•High-accuracystylustypeCNCSurface
Measuring Instrument that allows simultaneous measurement of surface roughness and form/contour.
•TheX1-andZ2-axeshavemaximumdrive speeds of 40mm/s and 200mm/s, respectively. This permits high-speed positioning that may result in a large increase in the throughput of multiple-profile / multiple-workpiece measurement tasks.
•AMitutoyoLaserHoloscaleisincorporatedin the X1- and Z1-axes so that high resolution [X1-axis: 6.25nm, Z1-axis: 4nm / 8nm (CS-5000CNC), 1nm/2nm (CS-H5000CNC)] is achieved and batch measurement of form/contour and surface roughness can be made.
•Theactivecontrolmethodisemployedforthe Z1-axis detector to implement a wide-range measurement capability wherein the variation in dynamic measuring force is
restricted.•SincetheZ1-axisdetectorincorporatesan
anti-collision safety device, the detector unit will automatically stop even if its main body collides with a workpiece or jig.
•CS-5000CNCismodelwiththea axis, it is possible to perform continuous measurement over horizontal and inclined surfaces by power-tilting the X1-axis.
•FormodelswiththeY-axistable,itispossible to expand the measuring range for multiple workpieces, etc., through positioning in the Y-axis direction.
•Suppliedwiththeeasy-to-operateRemoteBox, on which the user can make any movement by selecting the required axis using the two joysticks. The current axis selection is easily identified by the icon on the key top.
•UsesUSBforcommunicatingwiththeDataProcessing / Analysis Unit (optional).
CS-H5000CNC with personal computer system and software
Remote box Wide range detector employing active control technology
K-25
ASPHERICALPAKAspherical lens analysis program
Optional SoftwareFORMTRACEPAK Enables control of the optional motor-driven Y-axis table and rotary table for realizing efficient measurement automation. You can also perform contour evaluation that allows free analysis of level differences, angle, pitch, area and other characteristics based on surface roughness data. In addition, you can create an original inspection certificate by setting the print format to suit your particular requirements.
107
65.95
ø1.2
(31.5)
35.9540º
74.51
ø6
12.5
(6.5
)
ø4
ø1.2
(31.5)
65.9535.95
74.51107
ø6
12.7
5
(6.8
)
ø4
ø0.5mm ball
ø1.2
(31.5)
145.95115.95
40º
154.51187
ø6
(19)25
ø4
ø1.2
(31.5)
145.95115.95
60º
154.51187
ø6
(19)25
ø4
ø1.2
(31.5)
145.95115.95
154.51187
ø6
(19.
3)
25.2
5
ø4
ø0.5mmball
15
35.9565.95
ø4ø6
1.6
0.4
ø1.2
(1.1
)74.5 (31.5)0.6
106.6
6
0.6
40ºAA
10
ø4ø6
1.2
0.6ø0
.6
(1.1
)
0.4
40º
74.5 (31.5)0.4106.4
35.9565.95
6
AA
ø4ø6
12.5ø6 (6.5
)
4˚ 35.95
ø1.2
65.95
74.5 (31.5)3109
16
12AAD543*1: Standard-length stylus (tip radius: 5µm)12AAJ037*2: For CS-H5000CNC (tip radius: 5µm)Tip material: Diamond
12AAD544*1*2: Standard-length ball stylus (tip radius: 5µm)Tip material: Sapphire
12AAD545*1: Double-length stylus (tip radius: 5µm)12AAJ039*2: For CS-H5000CNC (tip radius: 5µm)Tip material: Diamond
12AAJ041*2: Double-length stylus (tip radius: 2µm)Tip material: Diamond
12AAD546*1*2: Double-length ball stylusTip material: Sapphire
12AAD651: Standard-length stylus for small holeTip radius: 5µmTip material: Diamond
12AAD652: Standard-length stylus for extra-small holeTip radius: 5µmTip material: Diamond
12AAD653: Standard-length eccentric stylusTip radius: 5µmTip material: Diamond
Detector Nosepiece
Unit: mm
*1: Standard accessory of CS-5000CNC*2: Standard accessory of CS-H5000CNC
K
SPECIFICATIONSModel No. CS-5000CNC CS-5000CNC CS-5000CNC CS-5000CNCOrder No.* (100V - 120V) 525-721-1 525-722-1 525-723-1 525-724-1Order No.* (200V - 240V) 525-721-2 525-722-2 525-723-2 525-724-2X1-axis measuring range 200mm 200mm 200mm 200mmZ2-axis vertical travel 300mm 300mm 300mm 300mmY-axis table unit — — Installed Installeda-axis unit — Installed — Installed
Model No. CS-5000CNC CS-5000CNC CS-5000CNC CS-5000CNCOrder No.* (100V - 120V) 525-741-1 525-742-1 525-743-1 525-744-1Order No.* (200V - 240V) 525-741-2 525-742-2 525-743-2 525-744-2X1-axis measuring range 200mm 200mm 200mm 200mmZ2-axis vertical travel 500mm 500mm 500mm 500mmY-axis table unit — — Installed Installeda-axis unit — Installed — Installed
*Select one of the optional accessory sets suited to your AC line voltage and measurement unit. 12AAL412 (mm, UL/CSA), 12AAL413 (mm, EU), 12AAL414 (mm, BS), 12AAL418 (mm, China), 12AAL419 (mm, EK), 12AAL415 (inch, UL/CSA), 12AAL416 (inch, EU), 12AAL417 (inch, BS), 12AAL420 (inch, China)
Model No. CS-H5000CNC CS-H5000CNCOrder No.* (100V - 120V) 525-761-1 525-763-1Order No.* (200V - 240V) 525-761-2 525-763-2X1-axis measuring range 200mm 200mmZ2-axis vertical travel 300mm 300mmY-axis table unit — Installeda-axis unit — —
*Select one of the optional accessory sets suited to your AC line voltage and measurement unit. 12AAL422 (mm, UL/CSA), 12AAL423 (mm, EU), 12AAL424 (mm, BS), 12AAL428 (mm, China), 12AAL429 (mm, EK), 12AAL425 (inch, UL/CSA), 12AAL426 (inch, EU), 12AAL427 (inch, BS), 12AAL430 (inch, China)
Stylus
Refer to the CNC Form Measuring Instrument Series leaflet (E4284) for more details.
K-26
Standard stylus
For small hole
Double-length for deep hole*4
For small hole/Double-length for deep hole*4
For extra small hole
For extra minute hole
For small hole*4*5
For ultra small hole*4*5
For deep hole (double-length and triple-length)*4 For small slotted hole
Styli
Colorcoding*3
Skidless nosepiece12AAB355
Detector
Detector (0.75mN): 178-396-2 Detector (4mN): 178-397-2
Detail-A
Detail-A
Detail-A
Detail-A
Ball ø0.5
Ball ø1.6
Detail-A (S=5/1)
12AAE882 (1µm)*1
12AAE924 (1µm)*2
12AAC731 (2µm)*1
12AAB403 (5µm)*2
12AAB415 (10µm)*2
12AAE883 (250µm)( ): Tip radius
12AAC732 (2µm)*1
12AAB404 (5µm)*2
12AAB416 (10µm)*2
( ): Tip radius
12AAE898 (2µm)*1
12AAE914 (5µm)*2
( ): Tip radius
12AAE892 (2µm)*1
12AAE908 (5µm)*2
( ): Tip radius
12AAE938 (2µm)*1
12AAE940 (5µm)*2
( ): Tip radius
12AAJ662 (0.5mm)( ): Tip radius
12AAE884 (0.8mm) ( ): Tip radius
12AAC733 (2µm)*1
12AAB405 (5µm)*2
12AAB417 (10µm)*2
( ): Tip radius
12AAC734 (2µm)*1
12AAB406 (5µm)*2
12AAB418 (10µm)*2
( ): Tip radius
3X stylus12AAC741 (2µm)*1
12AAB414 (5µm)*2
12AAB426 (10µm)*2
( ): Tip radius
2X stylus12AAC740 (2µm)*1
12AAB413 (5µm)*2
12AAB425 (10µm)*2
( ): Tip radius
60°/90°
0.9 37.7
7.6
44.7
ø2.4
ø1.2
5.2
A
14 60
ø8
ø14
ø14
ø7
10 11.5
3.1
3.6
1.3
4 Extension rods(12AAG202: 50mm, 12AAG203: 100mm)
Detail-A (S=5/1)
Detail-A (S=5/1)
Detail-A Detail-A
ø0.3
60°/90°
0.8
0.4
ø2.4
37.7
2.5
ø0.6
8.9
44.2
0.8
A
ø2.4
87.7 0.9
ø1.2
60°/90° 60°/90°
94.7
7.6
5.2
A
ø2.4
137.7 0.9
7.6
144.7
ø1.2
5.2
A
0.4
1.2
ø0.3
60°/90°
ø2.48.9
ø0.6
2.5
37.7
1.2
44.2
A
0.6
0.4
1.6 ø0.6
60°/90°
ø2.415
ø1.2
3.4 2.4
1.6
0.6 37.7
44.4
A
ø0.3
0.4
1.6
ø1.2
ø2.4
94.4
87.7 0.6
45
A
ø0.6
0.6
ø1.2
ø2.4
41
87.7
93.8
ø1.2
1.6
3.4
2.4 ø2
.4
94.4
87.7 0.6
30
A
0.6
ø0.6
3
1.8
0.6
ø2.4
94.7
87.7 0.9
Unit: mm
Colorcoding*3
Colorcoding*3
Colorcoding*3
Colorcoding*3
Colorcoding*3
ø0.3
ø2.4
43.8
37.7
8.5
3.1
A
Optional Styli for Surface Roughness MeasurementCompatible with SJ-400, SJ-500, SV-2100,SV-(C)3100, SV-(C)4100 series
K
*1: Tip angle 60°*2: Tip angle 90°*3:
Tip radius 1µm 2µm 5µm 10µm 250µmColor coding White Black No color Yellow No notch or color
*4: For downward-facing measurment only*5: Used for calibration, a standard step gauge (No.178-611, option) is also required.
K-27
60°
Styli
For deep groove (10mm) For deep groove (20mm)*4 / Double-length for deep hole
For rolling circle waviness*4 /*5 Double-length for deep hole
For deep groove (20mm) For deep groove (40mm)*4
For deep groove (30mm) For deep groove (30mm)*4 / Double-length for deep hole
For gear tooth For gear tooth*4 / Double-length for deep hole
For rolling circle waviness surface*5
For knife-edge detector For corner hole*4 / Double-length for deep hole
For eccentric arm*4 For bottom surface
Detail-A
Detail-A
Detail-A
Detail-A
Detail-A
Detail-A
12AAC735 (2µm)*1
12AAB409 (5µm)*2
12AAB421 (10µm)*2
( ): Tip radius
12AAE893 (2µm)*1
12AAE909 (5µm)*2
( ): Tip radius
12AAE895 (2µm)*1
12AAE911 (5µm)*2
( ): Tip radius
12AAE894 (2µm)*1
12AAE910 (5µm)*2
( ): Tip radius
12AAE896 (2µm)*1
12AAE912 (5µm)*2
( ): Tip radius
12AAE897 (2µm)*1
12AAE913 (5µm)*2
( ): Tip radius
12AAE899 (2µm)*1
12AAE915 (5µm)*2
( ): Tip radius
12AAE886 (0.25mm)( ): Tip radius
12AAC736 (2µm)*1
12AAB408 (5µm)*2
12AAB420 (10µm)*2
( ): Tip radius
12AAC737 (2µm)*1
12AAB407 (5µm)*2
12AAB419 (10µm)*2
( ): Tip radius
12AAB339 (2µm)*1
12AAB410 (5µm)*2
12AAB422 (10µm)*2
( ): Tip radius
12AAC738 (2µm)*1
12AAB411 (5µm)*2
12AAB423 (10µm)*2
( ): Tip radius
12AAC739 (2µm)*1
12AAB412 (5µm)*2
12AAB424 (10µm)*2
( ): Tip radius
12AAB338 (0.8mm)( ): Tip radius
13
ø2.4
ø1.2
60°/90°
60°/90°
14.2
44.737.7
A
23
0.9
ø2.4
24.2
ø1.2
37.7
44.7
A
33 31.8
5.2
ø1.2
A
ø2.4 ø2.4
60°/90°
37.7
45.2
60°
60°
7.6
6.4
37.7
43.8
ø1.2 ø2.4A
A37.71.4
60°/90°ø1.2
45.2
7.610
ø2.4
ø2.4
7.6
ø2.4
ø1.2
60°/90°
37.70.9
44.7
A
7.6
ø2.4
ø1.2
0.9 37.7
44.7
Ball ø1.588
5.2
0.9
23
21.8
5.2
95.2
Unit: mm
87.7
ø2.4
ø1.2
93.8
87.735
ø0.8
45°
5.8 5 ø1
.6
ø2.4
94.7
0.9 87.7
ø1.2 ø2.4
5.2
6.4
7.6
43.8
42.6
5.2
ø2.4
45.237.7
ø2.4
ø1.2
36.5
35
5.2
ø3
93.887.7
ø1.2
36.5
35
ø3
93.8
6.77
87.7
ø1.2
60°
Colorcoding*3
Colorcoding*3
Colorcoding*3
Colorcoding*3
Colorcoding*3
Colorcoding*3
25°6.2 5
ø2.4
ø1
60°/90°
37.70.5
44.3
7.4
K
*1: Tip angle 60°*2: Tip angle 90°*3:
Tip radius 1µm 2µm 5µm 10µm 250µmColor coding White Black No color Yellow No notch or color
*4: For downward-facing measurment only*5: Used for calibration, a standard step gauge (No.178-611, option) is also required.
K-28
K
Contracer CV-1000 / CV-2000SERIES 218 — Contour Measuring Instruments
FEATURES•AdigitalarcscaleisequippedintheZ-axis
detecting unit. This gives you a wider range of measurement with higher resolution. No more reliance on measurement magnifications.
•Adataanalysissystem(personalcomputersystem and FORMTRACEPAK software is available.
Connected to a personal computer, the FORMTRACEPAK contour analysis program provides various modes of measurement and analysis.
CV-1000N2 can be attached to the optical column stand.
Light emission device
Receiver ICArc scale
The CV-1000 is portable and can be carried to the machine-shop for measurement of large workpieces.
CV-2000S4 with personal computer system and software
CV-1000N2 with personal computer system and software
CV-2000M4 with personal computer system and software
Technical DataX1-axis Measuring range: 50mm (CV-1000) or 100mm (CV-2000) Resolution: 0.2µm Measurement method: Reflective-type linear encoder Drive speed: 0.2, 1mm/s and manual Measuring speed: 0.2, 0.5mm/s Measuring direction: Backward Traverse linearity: 3.5µm / 50mm (CV-1000),
3.5µm / 100mm (CV-2000) *with the X axis in horizontal orientation Linear displacement: ±(3.5+2L/100)µm
* L = Drive length (mm) Inclining range: ±45° (CV-2000)Z2-axis (column, CV-2000 only) Column type: Power drive (S4 type) ot Manual (M4 type) Vertical travel: 250mm (S4 type), 320mm (M4 type) Drive speed: 1 - 5mm/s and manual
Z1-axis (detector unit) Measuring range: 25mm (CV-1000) or 40mm (CV-2000) Resolution: 0.4µm (CV-1000) or 0.5µm (CV-2000) Measurement method: Arc encoder Linear displacement: ±(3.5+I4HI/25)µm
accuracy (at 20°C) *H: Measurement height from the horizontal position (mm)
Stylus up/down operation: Arc movement Face of stylus: Downward Measuring force: 10 - 30mN Traceable angle: Ascent: 77°, descent: 87°
(using the standard stylus provided and depending on the surface roughness)
Stylus tip Radius: 25µm, carbide tipBase size (W x H): 600 x 450mm (CV-2000)Base material: Granite (CV-2000)Mass: 5kg (CV-1000N2),
115.8kg (CV-2000M4), 130.3kg (CV-2000S4)
Power supply: 100 – 240VAC ±10%, 50/60Hz
Arc scale on the Z-axis
K-29
172-197172-142
172-143
218-003 172-144172-378172-234
176-107
218-002218-001 (mm)218-011 (inch)
218-024
178-023
Contracer CV-1000ContracerCV-2000
178-024
218-041 (mm)218-051 (inch)
K
SYSTEM DIAGRAM
Optional Accessories218-024: Column stand for CV-1000 (vertical travel: 320mm, inclination: ±45°)218-001: Cross-travel table (XY range: 100 x 50mm)218-011: Cross-travel table (XY range: 4” x 2")218-041: Cross-travel table (XY range: 50 x 25mm)218-051: Cross-travel table (XY range: 2” x 1")218-002: Rugged table176-107: Holder with clamp218-003: Rotary vise (heavy-duty type)172-144: Rotary vise172-234: V-block with clamp (Max. workpiece dia.: 50mm)172-378: V-block with clamp (Max. workpiece dia.: 25mm)172-197: Swivel center support172-142: Center support172-143: Center support riser178-023: Vibration isolator178-024: Vibration isolator stand998862: Pin gage unit for calibration (mm)998861: Pin gage unit for calibration (inch)––––––: Arms and styli (See page K34)* To denote your AC power cable add the following suffixes to the order No.: A
for UL/CSA, C for Taiwan, D for CEE, DC for CCC, E for BS, K for EK, No suffix is required for JIS/100V
SPECIFICATIONSModel No. CV-1000N2 CV-2000M4 CV-2000S4Order No. (mm) 218-611* 218-631* 218-632*Order No. (inch) 218-621* 218-641* 218-642*X1-axis measuring range 50mm 100mm 100mmZ1-axis measuring range 25mm 40mm 40mmZ2-axis vertical travel — 320mm 250mm
* To denote your AC power cable add the following suffixes to the order No.: A for UL/CSA, C for Taiwan, D for CEE, DC for CCC, E for BS, K for EK, No suffix is required for JIS/100V
K-30
Detector
Mirror
Mirror
Mirror
Scale
Mirror
Beam splitter
Laser diode
Beam splitter
K
Contracer CV-3100 / CV-4100SERIES 218 — Contour Measuring Instruments
FEATURES•Dramaticallyincreaseddrivespeed(X
axis: 80 mm/s, Z2-axis: 20 mm/s) further reduces total measurement time.
•Inordertomaintainthetraverselinearityspecification for an extended period of time, Mitutoyo has adopted highly rigid ceramic guides that combine the characteristics of smallest secular change and remarkable resistance to abrasion.
•Supportforawiderangeofoptionalperipherals designed for use with the CNC models enables simplified CNC measurement.
•Thedriveunit(X-axis)andcolumn(Z2-axis) are equipped with a high-accuracy linear encoders (ABS type on Z2-axis). This improves reproducibility of continuous automatic measurement of small holes in the vertical direction and repeated measurement of parts which are difficult to position.
•Xaxisaccuracy:±(0.8+0.01L)µm Z1-axis accuracy: ±(0.8+I0.5HI/25)µm*
Designed to handle workpieces calling for high accuracy. *CV-4100S4, H4, W4 types, L = Drive length, H = Measurement height (mm)
Technical DataX-axis Measuring range: 100mm or 200mm Resolution: 0.05µm Measurement method: linear encoder Drive speed: 0 - 80mm/s and manual Measuring speed: 0.02 - 5mm/s Measuring direction: Forward/backward Traverse linearity: 0.8µm / 100mm, 2µm / 200mm *with the X axis in horizontal orientation Linear displacement: ±(1+0.01L)µm (CV-3100S4, H4, W4)
accuracy (at 20°C) ±(0.8+0.01L)µm (CV-4100S4, H4, W4) ±(1+0.02L)µm (CV-3100S8, H8, W8) ±(0.8+0.02L)µm (CV-4100S8, H8, W8)
* L = Drive length (mm) Inclining range: ±45°
Z2-axis (column) Vertical travel: 300mm or 500mm Resolution: 1µm Measurement method: ABSOLUTE linear encoder Drive speed: 0 - 20mm/s and manualZ1-axis (detector unit) Measuring range: ±25mm Resolution: 0.2µm (CV-3100), 0.05µm (CV-4100) Measurement method: Linear encoder (CV-3100),
laser hologage (CV-4100) Linear displacement: ±(2+I4HI/100)µm (CV-3100)
accuracy (at 20°C) ±(0.8+I0.5HI/25)µm (CV-4100) *H: Measurement height from the horizontal
position (mm)
Stylus up/down operation: Arc movement Face of stylus: Upward/downward Measuring force: 30mN Traceable angle: Ascent: 77°, descent: 87°
(using the standard stylus provided and depending on the surface roughness)
Stylus tip Radius: 25µm, carbide tipBase size (W x H): 600 x 450mm or 1000 x 450mmBase material: GraniteMass
Main unit: 140kg (S4), 150kg (H4), 220kg (W4) 140kg (S8), 150kg (H8), 220kg (W8)
Controller Unit: 14kg Remote Control Box: 0.9kgPower supply: 100 – 240VAC ±10%, 50/60HzPower consumption: 400W (main unit only)
Mitutoyo's innovative Laser Hologage technology provides near interferometer-grade accuracy using the interference phenomenon of diffracted light, coupled with a resolution of 0.05µm over the entire detecting range of 50mm.
Hologage system
Collective Calibration Function •Adedicatedcalibrationgageenablestheuser
to calibrate the instrument for Z-axis gain, symmetry, stylus-tip radius, etc., in a single procedure.
CV-3100S4 with personal computer system and software
Using Rotary Table q1Using Y-axis Table
Using Rotary Table q2
Automatic Measuring Function•Supportforawiderangeofoptional
peripherals designed for use with the CNC models enables automatic measurement.
•ThedriveunitoftheCV-4100seriesisequipped with a Laser Hologage detector giving excellent narrow/wide range accuracy and resolution in the Z1-axis.
K-31
Data composition
Data 1 Data 2
K
SPECIFICATIONSModel No. CV-3100S4 CV-3100H4 CV-3100W4Order No. (mm) 218-421* 218-422* 218-423*Order No. (inch) 218-431* 218-432* 218-433*
A variety of models available for measuring requirements
CV-3100S4 / CV-4100S4Traverse range: 100mmVertical travel: 300mmBase size (W x D): 600 x 450mmBase material: Granite
CV-3100H4 / CV-4100H4Traverse range: 100mmVertical travel: 500mmBase size (W x D): 600 x 450mmBase material: Granite
CV-3100W4 / CV-4100W4Traverse range: 100mmVertical travel: 500mmBase size (W x D): 1000 x 450mmBase material: Granite
Model No. CV-3100S8 CV-3100H8 CV-3100W8Order No. (mm) 218-426* 218-427* 218-428*Order No. (inch) 218-436* 218-437* 218-438*
CV-3100S8 / CV-4100S8Traverse range: 200mmVertical travel: 300mmBase size (W x D): 600 x 450mmBase material: Granite
CV-3100H8 / CV-4100H8Traverse range: 200mmVertical travel: 500mmBase size (W x D): 600 x 450mmBase material: Granite
CV-3100W8 / CV-4100W8Traverse range: 200mmVertical travel: 500mmBase size (W x D): 1000 x 450mmBase material: Granite
Refer to the Contracer CV-3100 / 4100 Series leaflet (E4293) for more details.
Optional SoftwareFORMTRACEPAK V5
Measurement Control Screen
Data Composition Function
Automatic Circle/Line Application Function
Model No. CV-4100S4 CV-4100H4 CV-4100W4Order No. (mm) 218-461* 218-462* 218-463*Order No. (inch) 218-471* 218-472* 218-473*X1-axis measuring range 100mm 100mm 100mmVertical travel 300mm power column 500mm power column 500mm power columnGranite base size (WxD) 600 x 450mm 600 x 450mm 1000 x 450mmDimensions (main unit, WxDxH) 756 x 482 x 966mm 756 x 482 x 1166mm 1156 x 482 x 1176mmMass (main unit) 140kg 150kg 220kg
Model No. CV-4100S8 CV-4100H8 CV-4100W8Order No. (mm) 218-466* 218-467* 218-468*Order No. (inch) 218-476* 218-477* 218-478*X1-axis measuring range 200mm 200mm 200mmVertical travel 300mm power column 500mm power column 500mm power columnGranite base size (WxD) 600 x 450mm 600 x 450mm 1000 x 450mmDimensions (main unit, WxDxH) 766 x 482 x 966mm 766 x 482 x 1166mm 1166 x 482 x 1176mmMass (main unit) 140kg 150kg 220kg
* To denote your AC power cable add the following suffixes to the order No.: A for UL/CSA, C for Taiwan, D for CEE, DC for CCC, E for BS, K for EK, No suffix is required for JIS/100V
K-32
Detector
Mirror
Mirror
Mirror
Scale
Mirror
Beam splitter
Laser diode
Beam splitter
K
Technical DataX1-axis Measuring range: 200mm Resolution: 0.05µm Measurement method: Reflective-type linear encoder Drive speed: 200mm/s (max., CNC) 0 - 60mm/s (joystick) Measuring speed: 0.02 - 2mm/s Measuring direction: Forward/backward Traverse linearity: 2µm / 200mm *with the X axis in horizontal orientation Linear displacement accuracy (at 20°C):
±(1+4L/200)µm (CV-3000CNC), ±(0.8+4L/200)µm (CV-4000CNC) * L = Drive length (mm)
a-axis Inclination angle: -45° (CCW) to +10° (CW) Resolution: 0.000225° Inclination: 6°/sZ2-axis (column) Vertical travel: 300mm or 500mm Resolution: 0.05µm Measurement method: Reflective-type linear encoder Drive speed: 200mm/s (max., CNC) 0 - 60mm/s (joystick) Base size (W x H): 750 x 600mm Base material: GraniteZ1-axis (detector unit) Measuring range: ±25mm Resolution: 0.2µm (CV-3000CNC),
0.05µm (CV-4000CNC) Measurement method: Linear encoder (CV-3000CNC) Laser hologage (CV-4000CNC) Linear displacement: ± (2+I4HI/100)µm (CV-3000CNC)
accuracy (at 20°C) ± (0.8+I0.5HI/25)µm (CV-4000CNC) *H: Measurement height from the
horizontal position (mm) Stylus up/down operation: Arc movement Face of stylus: Upward/downward Measuring force: 30mN Traceable angle: Ascent: 70°, descent: 70°
(using the standard stylus provided and depending on the surface roughness)
Stylus tip Radius: 25µm, carbide tipY-axis* Measuring range 200mm Resolution 0.05µm Drive speed Max.200mm/s (in CNC mode) 0~60mm/s (in joystick control mode) Max. table loading 20kg Traverse linearity 2µm/200mm Linear displacement accuracy (20ºC) ±(2+2L/100)µm L = Length between arbitrary two point (mm) Mass: 240kg, 250kg (high column type) (The Y-axis table and a vibration isolating stand
are excluded.)Power supply: 100 – 240VAC ±10%, 50/60HzPower consumption: 500W (main unit only)
FEATURES•High-accuracyCNCcontour/form
measuring instrument.•X1-,Y-,andZ2-axeshaveamaximumdrive
speed of 200 mm/s, which permits high-speed positioning that may result in a large increase in the throughput of multiple-profile / multiple-workpiece measurement tasks.
•Formodelswiththea axis, it is possible to perform continuous measurement over horizontal and inclined surfaces by power-tilting the X1-axis.
•ThedriveunitoftheCV-4000CNCseriesisequipped with a Laser Hologage detector giving excellent narrow/wide range accuracy and resolution in the Z1-axis.
•FormodelswiththeY-axistable,itispossible to expand the measuring range for multiple workpieces, etc., through positioning in the Y-axis direction.
•Enablesinclinedplanemeasurementsthrough 2-axis simultaneous control in the X- and Y-axis directions.
•SincetheZ1-axisdetectorincorporatesananti-collision safety device, the detector unit will automatically stop even if its main body collides with a workpiece or jig.
•Suppliedwithaneasy-to-operateRemoteBox, on which the user can make any movement by selecting the required axis using the two joysticks. The current axis selection is easily identified by the icon on the key top.
•CommunicationwiththeDataProcessing/Analysis section is via USB.
CV-3000CNC with personal computer system and software
Contracer Extreme CV-3000CNC / CV-4000CNCSERIES 218 — CNC Contour Measuring Instruments
Mitutoyo's innovative Laser Hologage technology provides near interferometer-grade accuracy using the interference phenomenon of diffracted light, coupled with a resolution of 0.05µm over the entire detecting range of 50mm.
Hologage system
K-33
K
Refer to the CNC Form Measuring Instrument Series leaflet (E4284) for more details.
*1 Vibration insulating standVibration insulating mechanism: Diaphragm air spring Natural frequency : 2.5 - 3.5HzDamping mechanism: OrificeLeveling mechanism: Automatic control with mechanical valvesAir supply pressure: 390kPaMaximum loading capacity: 350kgDimensions (W x D x H): 1000 x 895 x 718mmMass: 290kg
SPECIFICATIONSModel No. CV-3000CNC CV-3000CNC CV-3000CNC CV-3000CNCOrder No.* (100V - 120V) 218-521-1 218-522-1 218-523-1 218-524-1Order No.* (200V - 240V) 218-521-2 218-522-2 218-523-2 218-524-2X1-axis measuring range 200mm 200mm 200mm 200mmZ2-axis vertical travel 300mm 300mm 300mm 300mmY-axis table unit*2 — — Installed Installeda-axis unit — Installed — InstalledVibration insulating stand*1 Installed Installed Installed InstalledGranite base size (WxD) 750 x 600mm 750 x 600mm 750 x 600mm 750 x 600mmDimensions (main unit, WxDxH) 800 x 620 x 1000mm 800 x 620 x 1000mm 800 x 620 x 1000mm 800 x 620 x 1000mmMass (main unit) 240kg 240kg 240kg 240kg
Model No. CV-3000CNC CV-3000CNC CV-3000CNC CV-3000CNCOrder No.* (100V - 120V) 218-541-1 218-542-1 218-543-1 218-544-1Order No.* (200V - 240V) 218-541-2 218-542-2 218-543-2 218-544-2X1-axis measuring range 200mm 200mm 200mm 200mmZ2-axis vertical travel 500mm 500mm 500mm 500mmY-axis table unit — — Installed Installeda-axis unit — Installed — InstalledVibration insulating stand*1 Installed Installed Installed InstalledGranite base size (WxD) 750 x 600mm 750 x 600mm 750 x 600mm 750 x 600mmDimensions (main unit, WxDxH) 800 x 620 x 1200mm 800 x 620 x 1200mm 800 x 620 x 1200mm 800 x 620 x 1200mmMass (main unit) 250kg 250kg 250kg 250kg
*Select one of the optional accessory sets suited to your AC line voltage and measurement unit. 12AAH790 (mm, UL/CSA), 12AAH791 (mm, EU), 12AAH792 (mm, BS), 12AAH796 (mm, China), 12AAH797 (mm, EK), 12AAH793 (inch, UL/CSA), 12AAH794 (inch, EU), 12AAH795 (inch, BS), 12AAH798 (inch, China)
Model No. CV-4000CNC CV-4000CNC CV-4000CNC CV-4000CNCOrder No.* (100V - 120V) 218-561-1 218-562-1 218-563-1 218-564-1Order No.* (200V - 240V) 218-561-2 218-562-2 218-563-2 218-564-2X1-axis measuring range 200mm 200mm 200mm 200mmZ2-axis vertical travel 300mm 300mm 300mm 300mmY-axis table unit*2 — — Installed Installeda-axis unit — Installed — InstalledVibration insulating stand*1 Installed Installed Installed InstalledGranite base size (WxD) 750 x 600mm 750 x 600mm 750 x 600mm 750 x 600mmDimensions (main unit, WxDxH) 800 x 620 x 1000mm 800 x 620 x 1000mm 800 x 620 x 1000mm 800 x 620 x 1000mmMass (main unit) 240kg 240kg 240kg 240kg
Model No. CV-4000CNC CV-4000CNC CV-4000CNC CV-4000CNCOrder No.* (100V - 120V) 218-581-1 218-582-1 218-583-1 218-584-1Order No.* (200V - 240V) 218-581-2 218-582-2 218-583-2 218-584-2X1-axis measuring range 200mm 200mm 200mm 200mmZ2-axis vertical travel 500mm 500mm 500mm 500mmY-axis table unit*2 — — Installed Installeda-axis unit — Installed — InstalledVibration insulating stand*1 Installed Installed Installed InstalledGranite base size (WxD) 750 x 600mm 750 x 600mm 750 x 600mm 750 x 600mmDimensions (main unit, WxDxH) 800 x 620 x 1200mm 800 x 620 x 1200mm 800 x 620 x 1200mm 800 x 620 x 1200mmMass (main unit) 250kg 250kg 250kg 250kg
*Select one of the optional accessory sets suited to your AC line voltage and measurement unit. 12AAH800 (mm, UL/CSA), 12AAH801 (mm, EU), 12AAH802 (mm, BS), 12AAH806 (mm, China), 12AAH807 (mm, EK), 12AAH803 (inch, UL/CSA), 12AAH804 (inch, EU), 12AAH805 (inch, BS), 12AAH808 (inch, China)
*2 Y-axis table unitMeasuring range: 200mmMinimum reading : 0.05µmScale unit: Reflective-type Linear Encoder Drive speed: Max. 200mm/s (CNC) 0 - 50mm/s (joystick)Maximum loading capacity: 20 kgTraverse linearity: 0.5µm/200mm (surface roughness) 2µm/200mm (contour)Linear displacement accuracy (at 20°C): ± (2+2L/100) µm, contour mode L: Dimension between two measured points (mm)Table size: 200 x 200mmDimensions (W x D x H): 320 x 646 x 105mmMass: 35kg
Data composition
Data 1 Data 2
Optional SoftwareFORMTRACEPAK V5
Measurement Control Screen
Data Composition Function
Automatic Circle/Line Application Function
K-34
H 15
ø8
40 Stylus
15515
ø8
H Stylus 25
145
H 95 155
H
Straight type For small-hole stylus Eccentric type
ø8
H H
40
932693 12AAE873 Tip shape: Single bevel Cone Tip angle: 20° 30° Tip radius: 25µm 25µm Tip material: Carbide Carbide
932694 12AAE874 Tip shape: Single bevel Cone Tip angle: 20° 30° Tip radius: 25µm 25µm Tip material: Carbide Carbide
932695 12AAE875 Tip shape: Single bevel Cone Tip angle: 20° 30° Tip radius: 25µm 25µm Tip material: Carbide Carbide
Tip angle: 20° Edge width: 3mm Tip radius: 25µm Tip material: Carbide
Ball dia: 1mm Tip material: Carbide
Tip angle: 12° Tip radius: 25µm Tip material: Carbide
Tip angle: 20° Tip radius: 25µm Tip material: Carbide
Tip angle: 20° Tip radius: 25µm Tip material: Carbide
Tip angle: 30°/50°* Tip radius: 25µm Tip material: Carbide, Sapphire, Diamond*
Single bevel Cross ground
Small hole: 932693 / 12AAE873 Small hole: 932694 / 12AAE874 Small hole: 932695 / 12AAE875
Knife edge Ball Cone
Cone
H
ø3 ø3
H H
ø3
ø3 ø3 ø3
H
ø6
ø1.6 H
12.5 50
ø6
ø3 H
50 20 50
Hø4
ø8
K
List of Applicable ArmsArm Order No. Compatible stylus
height
Straight type
935111 H = 6mm935112 H = 12mm935113 H = 20mm935114 H = 30mm935115 H = 42mm
Eccentrictype
935116 H = 6mm935117 H = 12mm935118 H = 20mm935119 H = 30mm935120 H = 42mm
Small hole 935110 H = 0.4, 1, 2.5mm
List of Applicable StyliStylus Order No. Stylus height
Single-bevel stylus carbide-tipped
354882 H = 6mm354883 H = 12mm354884 H = 20mm345885 H = 30mm354886 H = 42mm
Cross-ground stylus carbide-tipped
354887 H = 6mm354888 H = 12mm354889 H = 20mm354890 H = 30mm354891 H = 42mm
Cone stylus carbide-tipped tip angle 20°
12AAE865 H = 6mm12AAE866 H = 12mm12AAE867 H = 20mm12AAE868 H = 30mm12AAE869 H = 42mm
Cone stylus sapphire tipped tip angle 30° *Diamond tipped *tip angle 50°
354892 H = 6mm354893 H = 12mm354894 H = 20mm355129* H = 20mm354895 H = 30mm354896 H = 42mm
Cone stylus carbide-tipped tip angle 30°
12AAA566 H = 6mm12AAA567 H = 12mm12AAA568 H = 20mm12AAA569 H = 30mm12AAA570 H = 42mm
Knife-edge stylus carbide-tipped
354897 H = 6mm354898 H = 12mm354899 H = 20mm354900 H = 30mm354901 H = 42mm
Ball stylus carbide-tipped
354902 H = 6mm354903 H = 12mm354904 H = 20mm354905 H = 30mm354906 H = 42mm
Small-hole stylus carbide-tipped one-sided cut
932693 H = 0.4mm932694 H = 1mm932695 H = 2.5mm
Small-hole stylus carbide-tipped cone
12AAE873 H = 0.4mm12AAE874 H = 1mm12AAE875 H = 2.5mm
Optional Arms and Styli for Contour Measurement
For CV-1000 and CV-2000
K-35
H
130 15
ø8
15
ø3
Stylus 185 15
ø8
40 Stylus
185 15
ø8
H Stylus
Straight type For small-hole stylus Eccentric type
55 20
ø3 ø5
55 13
ø1.6
ø4
H
55
ø4
HHH
H
H
ø3 ø3
ø3 ø3
ø3
H
H
H
ø3
Tip shape: Single bevel Tip angle: 20° Tip radius: 25µm Tip material: Carbide
Tip shape: Single bevel Tip angle: 20° Tip radius: 25µm Tip material: Carbide
Tip angle: 20° Edge width: 3mm Tip radius: 25µm Tip material: Carbide
Ball dia: 1mm Tip material: Carbide
Tip angle: 12° Tip radius: 25µm Tip material: Carbide
Tip angle: 20° Tip radius: 25µm Tip material: Carbide
Tip angle: 20° Tip radius: 25µm Tip material: Carbide
Tip angle: 30°/50°* Tip radius: 25µm Tip material: Carbide, Sapphire, Diamond*
Single bevel Cross ground
Small hole: 12AAE297 Small hole: 12AAE298
Tip shape: Single bevel Tip angle: 20°Tip radius: 25µmTip material: Carbide
Small hole: 12AAE299
Knife edge Ball Cone
Cone
K
•Anyspecifiedarmandstylusotherthanabovelistedcanbecustom-madetospecialorder.
List of Applicable ArmsArm Order No. Compatible stylus
height
Straight type
12AAE294 H = 6mm12AAE295 H = 12mm996506 H = 20mm996507 H = 30mm996508 H = 42mm
Eccentrictype
996509 H = 6mm996510 H = 12mm996511 H = 20mm996512 H = 30mm996513 H = 42mm
Small hole 12AAE296 Small-hole stylus
List of Applicable StyliStylus Order No. Stylus height
Single-bevel stylus carbide-tipped
354882 H = 6mm354883 H = 12mm354884 H = 20mm345885 H = 30mm354886 H = 42mm
Cross-ground stylus carbide-tipped
354887 H = 6mm354888 H = 12mm354889 H = 20mm354890 H = 30mm354891 H = 42mm
Cone stylus carbide-tipped tip angle 20°
12AAE865 H = 6mm12AAE866 H = 12mm12AAE867 H = 20mm12AAE868 H = 30mm12AAE869 H = 42mm
Cone stylus sapphire tipped tip angle 30° *Diamond tipped *tip angle 50°
354892 H = 6mm354893 H = 12mm354894 H = 20mm355129* H = 20mm354895 H = 30mm354896 H = 42mm
Cone stylus carbide-tipped tip angle 30°
12AAA566 H = 6mm12AAA567 H = 12mm12AAA568 H = 20mm12AAA569 H = 30mm12AAA570 H = 42mm
Knife-edge stylus carbide-tipped
354897 H = 6mm354898 H = 12mm354899 H = 20mm354900 H = 30mm354901 H = 42mm
Ball stylus carbide-tipped
354902 H = 6mm354903 H = 12mm354904 H = 20mm354905 H = 30mm354906 H = 42mm
Small-hole stylus carbide-tipped one-sided cut
12AAE297 H = 0.4mm12AAE298 H = 1mm12AAE299 H = 2.5mm
For CV-3100, CV-4100, CV-3000CNC, CV-4000CNC, SV-C3100, SV-C4100, SV-C3000CNC and SV-C4000CNC
K-36
K
Optional Accessories for Automatic MeasurementFor SV series, SV-C series, CV series and CNC Models
Quick chuck: 211-032This chuck is useful when measuring small workpieces. You can easily clamp them with its knurled ring.
Retention range
Inner latch OD: ø1 - ø36mmInner latch ID: ø14 - ø70mOuter latch OD: ø1 - ø75mm
Dimensions ø118 x 41mmMass 1.2kg
Automatic-leveling table:178-087 (SV, CV, CS3200)Automatic-leveling table:178-037 (CNC Models)This is a stage that performs fully automatic leveling as measurement starts, freeing the user from this troublesome operation. Fully automatic leveling can be done quickly by anyone. In addition, the operation is easy and reliable.
Inclination adjustment angle ±2°Maximum load 7kgTable dimensions 130 x 100mmMass 3.5kg
Micro-chuck: 211-031This chuck is suitable for clamping extra-small diameter workpieces (ø1mm or less), which cannot be retained with the centering chuck.
Retention range OD: ø0 - ø1.5mmDimensions ø118 x 48.5mmMass 0.6kg
Displacement 360°Resolution 0.0072°Maximum load(loading moment)
4kg (343N•cmorless)
Rotational speed Max. 18°/sMass 5kg
Travel range 200mmResolution 0.05µmPositioning accuracy ±3µmDrive speed Max. 80mm/sMaximum load 50kgMass 28kg
q1-axis table: 12AAD975*For efficient measurement in the axial/transverse directions. When measuring a cylindrical workpiece, automatic alignment can be performed in combination with the Y-axis table. * q1-axis mounting plate (12AAE630) is required when directly installing on the base of the SV-3100.
q2-axis table: 178-078*You can measure multiple points on a cylindrical workpiece and automate front/rear-side measurement.* q2-axis mounting plate (12AAE718) is required when directly installing on the
base of the SV-3100.# It allows semi-automatic measurement with a Manual Type Machine by using
these items.
Y-axis table*: 178-097 For SV, SV-C and CV (not CNC models)Enables efficient, automatic measurement of multiple aligned workpieces and multiple points on a single measurement surface.* It allows semi-automatic measurement with a Manual Type Machine by using
these items.
Examples of optimal combinations of accessories for CNC models
For the combinations and the specifications of various optional accessories described in this catalog, contact your nearest Mitutoyo sales office.* : Applicable only to surface roughness measurement** : Applicable only for SV-M3000CNC
Optional accessory
Function
Y-axis Table
q1 Table q2 Table
Automatic leveling — — —Automatic alignment (Patent registered: Japan) l l —
Multiple workpiece batch measurement s — —
Measurement in the Y-axis direction l — —
Oblique measurement of the XY plane * l — —
Outside 3D surface roughness measurement/evaluation * l — —
Multiple-piece measurement in the Y-axis direction (Positioning in the Y-axis direction)
l — —
Multiple-piece measurement in the radial direction (Rotational positioning in the XY plane)
s l —
Inclined surface measurement in the X-axis direction s — —
Inclined hole inside measurement in the X-axis direction
s — —
Multiple cylinder generatrix line measurement s — l
Measurement of both top and bottom surfaces s — l
Rotary positioning of large workpiece ** — — —
Upward/downward and frontward/backward measurement of large workpiece **
— — —
Displacement 360ºResolution 0.004ºMaximum load 12kgRotational speed Max. 10º/sMass 7kg
K-37
Recorded profiles
Aligned Not aligned
End point
Axial line
Axial line
Traverse directionTraverse direction
End point
Start point
Start point
K
l: Essential s: Better to provide with —: Not necessary
Rotary vise218-003•Two-slidejaw
type.•Max.workpiece
size: ø60mm•Minimum
reading: 1°
Precision vise178-019•Max.workpiecesize:
36mm•Canbemountedona
leveling table.
Leveling table178-043-1 (mm), 178-053-1 (inch)•Tabletop:130 x 100mm•Levelingrange:±1.5°•XYtravel:±12.5mm
Digital leveling table178-042-1 (mm)•Tabletop:130 x 100mm•Levelingrange:±1.5°•XYtravel:±12.5mm
Leveling table178-016•Tabletop:130 x 100mm•Levelingrange:±1.5°•Height:40mm
Holder with clamp176-107• Used with a
cross-travel table or rugged table.
• Max. workpiece height: 35mm
Swivel center support172-197• Max. workpiece
dia.: 80mm* * 65mm when swiveled 10°
• Max. workpiece length: 140mm
Center support riser172-143•Usedwitha
center support.•Max.workpiece
dia.: 240mm
Center support172-142•Max.workpiece
dia.: 120mm•60mmriseris
optional
V-block with clamp172-234, 172-378• Used with a
cross-travel table or rugged table.
• Max. workpiece dia.: 50mm (172-234), 25mm (172-378)
Calibration stand12AAG175For mounting a roughness specimen or step gage during calibration.
172-378172-234
3-axis adjustment tableThis table helps make the alignment adjustments required when measuring cylindrical surfaces. The corrections for the pitch angle and the swivel angle are determined from a preliminary measurement and the Digimatic micrometers are adjusted accordingly. A flat-surfaced workpiece can also be leveled with this table.
178-047
V-block998291•Workpiecediameter:
1mm to 160mm•Canbemountedona
leveling table
Cross-travel table218-001 (mm), 218-011 (inch)•Tabletop:280 x 180mm•XYtravel:100 x 50mm
Cross-travel table218-041 (mm), 218-051 (inch)•Tabletop:280 x 152mm•XYtravel:50 x 25mm
Optional Accessories for Surftest / FormtracerCompatible with Desktop Models
Drive unit tilting function (Patent pending: Japan)
Large q Table Rotary-type detector holder
l — —
s — —
— — —
— — —
— — —
s — —
— — —
— — —
l — —
l — —
— — —
— — —
— l —
— — l
top related