filasystem - flooring libraryflooring-library.co.uk/uploads/1/images/company/132... · 1 fila has...
Post on 17-Jul-2020
3 Views
Preview:
TRANSCRIPT
1
www.filachim.com
Fila has always cared for all your surfaces in stone, porcelain, terracotta and wood, at every stage of treatment: from washing to protection and maintenance.
FILASYSTEMThe complete catalogue of Fila treatments.
TREATMENTSTAGES
TREATMENTCYCLES
WHAT TO DO IF
filasolutions.com
2
CONTENTSIntroduction page 4
Treatment stages
Pre-treatment page 5
Washing after laying page 6
Protection page 8
Finishing page 10
Maintenance page 12
Glossary page 14
Treatment cycles
Stone page 16
Agglomerates page 30
Porcelain page 34
Terracotta page 38
Wood page 45
Concrete page 45
Resin page 46
What to do if page 48
3
THE FILA SYSTEM: A WINNING STRATEGY TO ENHANCE MATERIALSRecommended by the world’s top floor and wall coverings manufacturers, Fila solutions are more
than just products. They deliver a complete treatment that stage after stage adds value to surfaces,
respecting their natural characteristics. From pre-treatment to maintenance, the Fila System
guarantees long-lasting results.
CLEANING Cleaning is of primary importance to enhance the beauty of surfaces and is divided into two stages:
- washing after laying
- maintenance (ordinary and extraordinary)
PROTECTIONProtecting materials from stains and humidity and at the same time achieving the desired look is a
fundamental process that takes three stages:
- pre-treatment
- basic protection (below referred to as “protection” to simplify matters)
- finishing protection (below referred to as “finishing”)
The following pages go into each individual treatment stage in detail, giving all the information necessary to ensure a long life for your floors and wall coverings.
INTRODUCTION
®
®
®
®
FILA is the only company in the world recommended by over
200 TOP BRANDS of materials for floors and wall coverings
3
4
Pre-treatment
Washing after laying
Protection
Finishing
Maintenance
TREATMENT STAGES
01234
5
PRE-TREATMENT
ADVANTAGES OF PRE-TREATMENT
it protects surfaces from grout residues
it makes grouting easier
it makes cleaning after laying simple
it speeds up drying after initial washing and
therefore also the subsequent treatment
stages.
PLEASE NOTE: This is not an obligatory stage, but it
is recommended when the material to be grouted is
very absorbent, like for example, terracotta and more
porous natural stone.
FILAPRW200PRE-GROUTING PROTECTOR
FILAPRW200 is the new water-repellent protector from Fila devised to protect floors between laying and grouting. It is effective against dirt produced when laying and makes grouting and cleaning easier without altering the material’s appearance.
0
Advice from the expert:when to pre-treat
Untreated UntreatedTreated with FILAPRW200 Treated with FILAPRW200
after washing after washing after washing after washing
Anti-stain testing carried out on Vicenza stone and terracotta. The untreated section absorbed the cement deep down, and made washing after laying difficult. The treated part did not absorb the cement, which was easy to remove with a specific detergent.
Ideal for absorbent materials such as quarry tiles, natural and manufactured stone, agglomerates and terracotta.
3
Material laid with adhesive should be pre-treated at least one day prior to grouting
5
ADVANTAGES OF WASHING AFTER LAYING
it makes the subsequent stages of protection
and maintenance easier
it removes residues of cement, adhesive and
various kinds of dirt
it stops these substances from adhering to
the surface, which would make subsequent
protection treatment ineffective.
WASHING AFTER LAYING
Tumbled marble floor before cleaning. After washing with DETERDEk: the surface is completely clean.
1
THE RIGHT PRODUCT FOR EVERY SURFACE
In the Fila range you will find the ideal product for correct effective cleaning after laying
Terracotta Acid DETERDEk
Porcelain, ceramic tiles Acid DETERDEk
Metallic porcelain tiles Neutral FILACLEANER
Glass mosaic, porcelain tiles andglazed ceramic tiles grouted with epoxy grout
Alkaline FILACR10
Marble, granite, travertine,polished agglomerates
Neutral FILACLEANER
Unpolished acid-resistant stone Acid DETERDEk
Resin, marble resin, quartz resin Neutral FILACLEANER
Manufactured stone,marble chip tiles
Alkaline FILAPS87
MATERIAL TYPE OF PRODUCT FILA PRODUCT
6
77
Acid detergents: for removing inorganic dirt, like for example residues of whitewash, limescale residues, rust, concrete, plaster residues, wall paint and building dirt in general.
Neutral detergents: for daily cleaning, they remove various kinds of dirt while totally respecting surfaces, even the most delicate.
Alkaline detergents: for removing organic dirt, normal kitchen and daily dirt. Including grease, oil, tomato, Coca Cola, wine, beer… etc.
Left: the floor at Catullo Airport in Verona before cleaning. Right: the same floor after washing with FILACLEANER after laying.
Left: an untreated terracotta floor after laying.Right: results after using DETERDEk are obvious.
DETERDEk, FILACLEANER, FILAPS87PERFECT CLEANING AFTER LAYING
FILACLEANER, DETERDEk and FILAPS87 ensure completely trouble-free cleaning after laying:
They respect the surfaces to be cleaned
They do not erode metal or aluminium parts (handles, hoods, door and window frames…)
They do not emit fumes that are harmful to the operator or the environment
3
3
3
pH scale
Advice from the expert:be careful with acid!
A metal edging dipped in hydrochloric acid; the aggressive effect of the acid is obvious.
A metal edging dipped in DETERDEk, remains unaltered.
Given that 90% of washing after laying entails the use of acid products, it is a good idea to:
Avoid acids that are too aggressive, which risk harming surfaces;
Choose buffered acids, which do not release harmful fumes for the operator;
Choose acids that do not harm other fittings (edges in aluminium, hoods, door and window frames…);
Choose products that not only remove encrusted dirt but also clean and therefore avoid having to repeat the procedure with other products
If all instructions are followed, cleaning after laying will be a very simple operation and above all will guarantee a brilliant future for your surfaces.
pH 14Alkaline
pH 0Acid
DETERDEk (dil. 10%)
pH1,5
FILAvIA BAGNO
pH2,2
FILACLEANER(dil. 10%)
pH 7Neutral
pH7
FUGANET
pH12,4
FILAPS87 FILACR10
pH12,5
pH12,7
8
2Having carefully washed the material after laying, you can proceed with protecting it.
ADVANTAGES OF PROTECTION
• It prevents absorption of water and oil stains;• It makes maintenance simpler;• It prolongs the life of materials.
THIS PROCEDURE IS PARTICULARLY RECOMMENDED FOR:
• Absorbent materials, for example calcareous stone, polished marble, polished porcelain and terracotta surfaces exposed to the risk of stains, for example floors and worktops in bathrooms, kitchens, showers, saunas and swimming pools:
• Exterior floors and surfaces.
PROTECTION
Water-repellent protectors prevent water from penetrating, creating the so-called “drop effect” clearly visible in the photo.
In addition to protecting surfaces from water, Fila water-repellent products prevent the formation of algae, efflorescence and damp stains.
Maintenance was carried out on both these buildings at the same time, but only the one on the right was protected with HYDROREP.
Advice from the expert:anti-graffiti treatment.
How to protect your surfaces from graffiti, smog and dust? For polished stone and polished porcelain use FILAMP90 stain protector or FILAMP90 ECO PLUS. For unpolished stone and fair-faced brick apply FILAW68 stain protector. For maintenance washing use FILANOPAINTSTAR detergent.
CHOOSE THE PRODUCT ACCORDING TO:
• The material to be treated; • The location of the material (inside or out,
floors or walls)• The type of protection (water-repellent,
stain-resistant)• The desired effect (natural, colour-
enhancing, wet look)
8
9
Advice from the expert:choose according to available time.
The speed of the protective treatment is often one of the requirements that affects choice. When the job must be completed quickly, it is better to opt for water-based products, which are more versatile and faster. If time permits, however, solvent-based products can be used, and can only be applied to perfectly dry surfaces.
Polished ceramic and porcelain tiles
Stain protection Natural FILAMP90 (solvent based)
FILAMP90 ECO PLUS (water based)
Marble, granite, travertine, polished agglomerates
Stain protection Colour-enhancing FILASTONE PLUS(solvent based)
Marble, granite, travertine, polished agglomerates
Stain protection Natural FILAMP90 (solvent based)
FILAMP90 ECO PLUS (water based)
Marble, granite, travertine, unpolished agglomerates
Stain protection Wet-look FILAPT10(water based)
Natural stone Water-repellent Natural HYDROREP (solvent based)
or FILAW68 (water based)
Natural stone Stain protection Colour-enhancing FILASTONEPLUS(solvent based)
Natural stone Stain protection Natural FILAFOB (solvent based)or FILAW68 (water based)
Natural stone Stain protection Wet-look FILAWET (solvent based)FILAPT10 (water based)
Polished natural stone and polished porcelain
Anti-graffiti Natural FILAMP90 (solvent based)
FILAMP90 ECO PLUS (water based)
Unpolished natural stone terracotta
Anti-graffiti Natural FILAW68(water based)
Quarry tiles, brickwork and Terracotta
Water-repellent Natural FILAW68 (water based)
Quarry tiles, brickwork and Terracotta
Stain protection Natural FILAFOB (solvent based)or FILAW68 (water based)
Terracotta Stain protection Wet-look FILAPT10(water based)
Concrete Dirt-repellent Natural FILABETON(water based)
MATERIAL WHERE IT IS LAYED TYPE OF PROTECTION EFFECT PRODUCT
THE RIGHT PRODUCT FOR EVERY SURFACE
SOLVENT BASEDWATER REPELLENT PROTECTORS
WATER BASEDSTAINPROTECTORS
penetratedeeper
have low environmental impact
are recommended for compact material that does not absorb well
are odourless
can be applied even when there is residual moisture
are better in the case of more porous, highly absorbent materials.
are breathable because they penetrate right into the material’s pores, repelling water and allowing air and water vapour to pass.
are breathable because they penetrate right into the material’s pores, repelling water and allowing air and water vapour to pass.
are suitable forexterior surfaces are suitable mainly
for interior floors
protect materialsfrom the weather
are useful in the case of exterior surfaces that may stain, under parked cars for example
prevent the formation of moss, mould and efflorescence.
also protect worktops, basins and doorsteps.
give the material the desired effect: natural, colour-enhancing or wet-look.
WATER-BASED OR SOLVENT-BASED PROTECTORS?
WATER-REPELLENT PROTECTIONOR STAIN-RESISTANT?
3 3
33
3 3
3
3
3
3
3
33
3
3
9
After protection, we recommend you apply a finishing product, generally a wax.
ADVANTAGES OF FINISHING
• It nourishes the floor• It protects from surface wear, caused by
traffic or moving furniture• It makes subsequent maintenance easier• It allows the desired appearance to be
obtained, from shiny to matt
3FINISHING
Application of a wax will make the surface look more nourished and brilliant.
Advice from the expert: when to use and when not to use wax
Finishes should only be carried out on interior floors, preferably not in damp rooms or where there is stagnant water (bathrooms, showers).
• For polished finishes, the wax can be used instead of waterproofing or during maintenance
• Finishing waxes should not be applied to porcelain or ceramic tiles
10
11
WAXES FOR 4 DIFFERENT EFFECTS
Advice from the expert:wash&wax
For on-going optimum protection, we recommend occasionally to apply a solution of diluted wax after washing with FILACLEANER. Use FILASATIN, FILACLASSIC or FILAMATT (depending on the effect desired), diluting 2 or 3 glasses in 5 litres of water.
FILAMATT
9natural-effect wax
FILASATIN
9satin-effect wax
FILALONGLIFE
9self-polishing high-gloss wax
FILACLASSIC
9buffable emulsion with typical wax effect
FILA PRODUCT EFFECT FILA PRODUCT EFFECT
11
12
4MAINTENANCE
ORDINARY MAINTENANCE
Maintenance is nothing more than regular cleaning of the home. It removes dirt, eliminates footprints and reinforces the protective layer. A simple job in most cases, which takes very little time thanks to Fila detergents.
Fila has the ideal product also for ceramic tiles in the bathroom: the anti-limescale detergent FILAvIA BAGNO.
Do not use alcohol or ammonia. Alcohol and ammonia harm surfa-ces, treatments and finishing wa-xes, altering their natural beauty. Never use them, even on stains. These can be removed with Fila products.
It is better to use warm water. Fila cleaning products give op-timum results, but they become unbeatable with the addition of some warm water. Diluting the detergents actually increases their effectiveness. Remember this and you will achieve surpri-sing results.
No steam, thank you.Fila advises against using steam machines on all wooden floors and on waxed floors. Fila pro-ducts allow you to clean just as quickly, but much more satisfac-torily and without harming the materials.
Advice from the expert:a few simple tipsfor better cleaning.
1
2
3
FilaCLEANER Concentrated neutral detergent for the MAINTENANCE of every surface
FilaBRIOUniversal spray detergent ofr every kind of wall
claddings, ceramic tiles, plastic laminates, glazed surfaces, stainless steel, glasses and mirrors
FilaVIABAGNO
Limescale removing spray detergent. It cleans all bathroom surfaces (porcelain tiles, glass,
stainless steel)
FilaNODROPS Water mark repellent protective detergent. Prevents traces and streaks of limescale
FilaREFRESHProtective detergent for tops. Cleans the
surfaces and reinforces the anti-stain protection of marble, granite and all treated natural stone
FUGANET Deep-down cleaner for grouts inceramic tile floors and walls.
THE RIGHT PRODUCT FOR EVERY SURFACE
12
13
EXTRAORDINARY MAINTENANCE
Certain situations call for extraordinary maintenance. For example:
RESTORING SURFACES
• The treatment on your floor is very old, damaged or ineffective
• When the surface has lost its original beauty due to incorrect maintenance, the time has come to remove old treatments or old layers of wax and replace them.
STAIN REMOVALIf your surface is stained, Fila makes removing these stains easy. All you need to do is choose the right product for each kind of material, then and follow the instructions on the label and in this table.
1 2
3 4
When removing stains from wax-treated terracotta and natural stones, the wax must be reapplied afterwards.
* do not use DETERDEk on shiny marble or in general on acid-sensitive materials (e.g. black slate). Carry out a preliminary test on ceramic tiles to check their resistance to the product.
Oil or grease FilaPS87 FilaNOSPOT or FilaSOLV FilaNOSPOT or FilaSOLV
Coloured stains (coffee, wine, soft drinks, hair dye, ink, felt
pens, nicotine, fruit juices)FilaPS87 or FilaSR95 FilaPS87 or FilaSR95 FilaPS87 or FilaSR95
Acid aggression(wine, lemon, anti-limescale…) -
FilaMARBLE RESTORER(small surfaces)
FilaKRISTALL PLUS (large surfaces)
-
Paint, graffiti FilaPS87or FilaNOPAINT STAR
FilaPS87 or FilaNOPAINT STAR
FilaPS87or FilaNOPAINT STAR
Rust, sulphate and marks left by metals FilaNO RUST or DETERDEK *
FilaNO RUST or DETERDEK *
FilaNO RUST or DETERDEK *
Concrete, saltpetre, limescale DETERDEK * DETERDEK * DETERDEK
Candle wax, tar FilaZERO SIL or FilaSOLV FilaZERO SIL or FilaSOLV FilaZERO SIL or FilaSOLV
Silicone, resin, glue, candle wax, sticky tape, old labels and polyurethane foam. FilaZERO SIL FilaZERO SIL FilaZERO SIL
Mould FilaACTIVE1 FilaACTIVE1 FilaACTIVE1
PORCELAIN AND CERAMICS NATURAL STONE TERRACOTTATYPE OF STAIN
THE RIGHT PRODUCT FOR EVERY SURFACE
13
14
Coverages are indicative, may vary depending on absorption of the materials, on treatment stage (washing after laying or restoring) and refer to one coat.
Do not apply Filajet protector and finishing products like wax in damp rooms and where there is stagnant water (bathrooms and showers).
The treatment cycle is complete when the surface can be walked on. Warning: this means that the surface can be walked on with care. You must wait at least 24 hours for optimum protection.
Maintenance treatments given here have been elaborated to restore previous treatments using Fila products. When the original treatment is unknown, we recommend consulting a Fila expert.
Before application, always read the instructions on the product label carefully.
This information is the fruit of our most recent technical knowledge and backed by continuous research and laboratory testing. However, due to factors outside our control, the suggestions given must always be checked and tried out by the user.Fila assumes no responsibility for incorrect use of its products.
Warning:
GlossaryWashing after laying: this cleans the surface of residues of concrete, glue and various kinds of dirt left after laying.
Restoring sheen: treatment to restore the material’s original sheen, to be carried out when the surface looks dull or damaged by acid stains.
Restoring protection: process to renew the material’s protection, to be carried out when the current treatment is very old, damaged or ineffective.
Restoring finishes: process to renew the protection of surface finishes, to be carried out when the material has old, worn, dirty or dull layers of wax.
Removing graffiti, smog and dust: exterior surfaces ruined by graffiti or blackened by smog and dust that need deep-down cleaning and restoration of the material’s protection with specific products.
Water-repellent protection: this protects the surface from water, watery stains (wine, coffee), wear by the weather and prevents the formation of moss, mould and efflorescence.
Stain protection: a treatment for water-oil repellent protection. It combines protection against greasy and oily stains with water repellence.
Anti-graffiti protection: to be carried out on exterior, vertical, absorbent surfaces to avoid graffiti and spray paint stains, making cleaning easier.
Dirt-repellent protection: protection recommended against dirt from through traffic. Particularly suitable for interior floors with rough-finish.
Anti-dust protection/treatment: protective treatment recommended for interior vertical surfaces to prevent dust settling, especially recommended for bricks or untreated stone. Treated material is easier to clean.
Basic protection: impregnation of the material that gives the surface initial protection and allows subsequent treatments to be absorbed more evenly.
Natural effect: “natural effect” is used to describe any treatment (protective or finish) that does not alter the material’s natural appearance.
Reviving/colour-enhancing: “reviving/colour-enhancing” is used to describe any treatment (protective or finish) that enhances the material’s natural colour, giving it a pleasant appearance.
Wet look: “wet look” is used to describe any treatment (protective) that revives the material to give a shiny effect.
Satin effect: “satin effect” is used to describe any treatment (finish) that gives the surface a silky, slightly glossy sheen.
Glossy effect: “glossy effect” is used to describe any treatment (finish) that gives the surface greater shine.
Ordinary maintenance: ordinary cleaning of surfaces to remove dirt, foot prints and strengthen the protective layer.
Extraordinary maintenance: cleaning to remove stains and intense dirt that is difficult to remove with simple ordinary maintenance.
14
15
A treatment cycle for each material.
STONE
Natural stone pag. 16
Low absorbency pag. 16
High absorbency pag. 20
Cobblestones, tumbled or sand-blasted marble pag. 22
Polished or brushed finish pag. 26
Manufactured stone 27
AGGLOMERATES
Unpolished agglomerates pag. 30
Polished agglomerates pag. 31
PORCELAIN
Enamelled ceramic tiles pag. 34
Polished porcelain pag. 34
Lappato porcelain pag. 35
Textured porcelain pag. 36
Crackle-glaze ceramic tiles pag. 37
TERRACOTTA
Terracotta pag. 38
Terracotta / unglazed quarry tiles pag. 41
Unglazed quarry tiles pag. 42
Terracotta brickwork pag. 43
WOOD
Wax treatment pag. 45
CONCRETE
Decorated concrete pag. 45
Concrete pag. 46
RESIN FLOORS pag. 46
GROUTING pag. 47
15
16
PROTECTION
NATURAL STONESLow absorbencyMatt or unpolished finish (Slate, Porphyry, Basaltine, Trachyte, Granite)SOLVENT-BASED PRODUCTS
RESTORINGFINISHES
FILAPS87diluted 1:5coverage: 30 m2/1L
on dry surface
WASH
RESTORINGPROTECTION
FILAPS87diluted 1:5coverage: 30 m2/1L
on drysurface
DETERDEkdiluted 1:5coverage: 20 m2/1L
AFTER LAYING
on drysurface
NATURAL EFFECT AGAINST STAINS
FILAFOBpurecoverage: 20 m2/1L1 coat
after 24 h
Indoors
WARNING:to be used onlyon acid-resistant stones
FILASTONE PLUS*purecoverage: 20 m2/1L1 or 2 coats, 2nd coat after 8 h
COLOUR-ENHANCING AGAINST STAINS
can bewalked on
after 8 h
WARNING: remove any excess during the application as mentioned in the product label
FINISHING
FILAMATTpurecoverage: 30-40 m2/1L2 coats, 2nd coat after 1 h
FILALONGLIFEpurecoverage: 30-40 m2/1L2 coats, 2nd coat after 1 h
SHINY EFFECT
NATURAL EFFECT
can bewalked on
after 1 h
FILASATINpurecoverage: 30-40 m2/1L2 coats, 2nd coat after 1 h
SATIN EFFECT
can bewalked on
after 1 h
can bewalked on
after 1 h
FILACLEANERdiluted: 1:200
coverage: 1500 m2/1L
ORDINARY
MAINTENANCE
FILACLEANERdiluted: 1:30
coverage: 50 m2/1L
one coat of your chosen finishing wax
EXTRAORDINARY
Verticalsurfaces
Horizontal surfaces
The expert’s advice: treatment of slates
For the washing after laying of slates, we recommend to check the resistance of the material to the acid detergent DETERDEk. As an alternative, use the neutral detergent FILACLEANER (diluted 1:30).For the treatment of slates layed indoors, the protection stage in an optional. After the initial wash, only apply 2 coats of your chosen finishing wax. Attention: for bathrooms and damp rooms do not apply wax. We recommend stain-protection (see treatment on page 20).
* for restoring tratment apply a single coat of the last protective product used.
The expert’s advice: pre-treat with FILAPRW200To protect material from grouting dirt and facilitate cleaning after laying, pre-treat the surface with a coat of pre-grouting protector FILAPRW200 (pure; coverage: for terracotta 8/10 m2, for stone 10/20 m2 per liter)
17
PROTECTION
NATURAL STONESLow absorbencyMatt or unpolished finish (Slate, Porphyry, Basaltine, Trachyte, Granite)WATER-BASED PRODUCTS
FILAMP90 ECO PLUSpurecoverage: 20 m2/1L1 coat working completely into the material
NATURAL EFFECT AGAINST STAINS
RESTORINGFINISHES
FILAPS87diluted 1:5coverage: 30 m2/1L
on dry surface
WASH
RESTORINGPROTECTION
FILAPS87diluted 1:5coverage: 30 m2/1L
on drysurface
DETERDEkdiluted 1:5coverage: 20 m2/1L
AFTER LAYING
on drysurface
on dry surface,can bewalked on
Indoors
WARNING:to be used onlyon acid-resistant stones
COLOUR-ENHANCINGAGAINST STAINS(CHECk THE AvAILABILITY FOR YOUR MARkET)
WARNING: before the product dries, remove any residue.
FINISHING
FILAMATTpurecoverage: 30-40 m2/1L2 coats, 2nd coat after 1 h
FILALONGLIFEpurecoverage: 30-40 m2/1L2 coats, 2nd coat after 1 h
SHINY EFFECT
NATURAL EFFECT
can bewalked on
after 1 h
FILASATINpurecoverage: 30-40 m2/1L2 coats, 2nd coat after 1 h
SATIN EFFECT
can bewalked on
after 1 h
can bewalked on
after 1 h
FILACLEANERdiluted: 1:200
coverage: 1500 m2/1L
ORDINARY
MAINTENANCE
FILACLEANERdiluted: 1:30
coverage: 50 m2/1L
one coat of your chosen finishing wax
EXTRAORDINARY
* for restoring tratment apply a single coat of the last protective product used.
Verticalsurfaces
Horizontal surfaces
The expert’s advice:pre-treat with FILAPRW200To protect material from grouting dirt and facilitate cleaning after laying, pre-treat the surface with a coat of pre-grouting protector FILAPRW200 (pure; coverage: for terracotta 8/10 m2, for stone 10/20 m2 per liter)
FILAPT10*pure o diluted 1:1coverage: 10-20 m2/1L2 coats, 2nd coat after 3 h
on dry surface,can bewalked on
WARNING:to remove FILAPT10 in the event of incorrect application or when deep-down cleaning is required, use the FILANOPAINT STAR cleaner.
The expert’s advice: treatment of slates
For the washing after laying of slates, we recommend to check the resistance of the material to the acid detergent DETERDEk. As an alternative, use the neutral detergent FILACLEANER (diluted 1:30).For the treatment of slates layed indoors, the protection stage in an optional. After the initial wash, only apply 2 coats of your chosen finishing wax. Attention: for bathrooms and damp rooms do not apply wax. We recommend stain-protection (see treatment on page 20).
18
WASH
NATURAL STONESLow absorbencyMatt or unpolished finish (Slate, Porphyry, Basaltine, Trachyte, Granite)SOLVENT-BASED PRODUCTS
HYDROREPpurecoverage: 20 m2/1L 1 coat
HYDROREP*purecoverage: 20 m2/1L 1 or 2 coats, 2nd coat after 24 h
FILAFOB*purecoverage: 20 m2/1L1 coat
FILASTONE PLUS*purecoverage: 20 m2/1L1 or 2 coats, 2nd coat after 8 h
FILAPS87diluted 1:5coverage: 30 v/1L
RESTORINGWASH TO REMOvE GRAFFITI AND SMOG
FILANOPAINT STARpurecoverage: 5 m2/1L
* for restoring tratment apply a single coat of the last protective product used.
NATURAL EFFECT AGAINST STAINS
WET LOOkAGAINST STAINS
FILAWET*purecoverage: 20 m2/1L1 or 2 coats, 2nd coat after 24 h
COLOUR-ENHANCING AGAINST STAINS
WATER REPELLENT
WATER REPELLENT
PROTECTION
RESTORINGPROTECTION
DETERDEkdiluted 1:5coverage: 20 m2/1L
AFTER LAYINGon dry surface,can be walked on
on dry surface,can bewalked on
After 24 h
can bewalked onafter 8 h
on dry surface,can bewalked on
on drysurface
on drysurface
on drysurface
WARNING: to remove FILAWET in the event of incorrect application or when deep-down cleaning is required, use the FILANOPAINT STAR cleaner.
WARNING: remove any excess during the application as mentioned in the product label.
WARNING:to be used onlyon acid-resistant stones
Outdoors
FILACLEANERdiluted: 1:200
coverage: 1500 m2/1L
ORDINARY
MAINTENANCE
FILAPS87diluted: 1:10
coverage: 100 m2/1L
EXTRAORDINARY
Verticalsurfaces
Horizontal surfaces
The expert’s advice:pre-treat with FILAPRW200To protect material from grouting dirt and facilitate cleaning after laying, pre-treat the surface with a coat of pre-grouting protector FILAPRW200 (pure; coverage: for terracotta 8/10 m2, for stone 10/20 m2 per liter)
19
WASH
NATURAL STONESLow absorbencyMatt or unpolished finish (Slate, Porphyry, Basaltine, Trachyte, Granite)WATER-BASED PRODUCTS
FILAPS87diluted 1:5coverage: 30 v/1L
RESTORINGWASH TO REMOvE GRAFFITI AND SMOG
FILANOPAINT STARpurecoverage: 5 m2/1L
RESTORINGPROTECTION
DETERDEkdiluted 1:5coverage: 20 m2/1L
AFTER LAYING
on drysurface
on drysurface
on drysurface
WARNING:to be used onlyon acid-resistant stones
Outdoors
FILACLEANERdiluted: 1:200
coverage: 1500 m2/1L
ORDINARY
MAINTENANCE
FILAPS87diluted: 1:10
coverage: 100 m2/1L
EXTRAORDINARY
Verticalsurfaces
Horizontal surfaces
PROTECTION
FILAMP90 ECO PLUSpurecoverage: 10-20 m2/1L1 coat working completely into the material
NATURAL EFFECT AGAINST STAINS
on dry surface,can bewalked on
COLOUR-ENHANCINGAGAINST STAINS(CHECk THE AvAILABILITY FOR YOUR MARkET)
WARNING: before the product dries, remove any residue.
FILAPT10*pure o diluted 1:1coverage: 10-20 m2/1L2 coats, 2nd coat after 3 h
WET LOOkAGAINST STAINS
on dry surface,can bewalked on
* for restoring tratment apply a single coat of the last protective product used.
The expert’s advice: pre-treat with FILAPRW200To protect material from grouting dirt and facilitate cleaning after laying, pre-treat the surface with a coat of pre-grouting protector FILAPRW200 (pure; coverage: for terracotta 8/10 m2, for stone 10/20 m2 per liter)
WARNING:to remove FILAPT10 in the event of incorrect application or when deep-down cleaning is required, use the FILANOPAINT STAR cleaner.
20
WASH
NATURAL STONES High absorbencyMatt or unpolished finish(Unpolished limestone, Vicenza stone, Lecce stone, Pietra Serena, Split-Finish Quartz)
FILAW68purecoverage: 10 m2/1L1 coat
FILAJETpurecoverage: 30 m2/1L1 coat
FILAJETpurecoverage: 30 m2/1L1 coat
FILAPS87diluted 1:5coverage: 20 m2/1L
NATURAL EFFECT AGAINST STAINS
AGAINST DIRT
AGAINST DIRTRESTORINGPROTECTION
FILACLEANERdiluted 1:30coverage: 50 m2/1L
on drysurface
on drysurface
AFTER LAYING
FINISHING
FILALONGLIFEpurecoverage: 30-40 m2/1L2 coats, 2nd coat after 1 h
SHINY EFFECT
FILAMATTpurecoverage: 30-40 m2/1L2 coats, 2nd coat after 1 h
FILASATINpurecoverage: 30-40 m2/1L2 coats, 2nd coat after 1 h
SATIN EFFECT
FILACLASSICpurecoverage: 30-40 m2/1L1 or 2 coats, 2nd coat after 1 h
SHINY EFFECT
NATURAL EFFECT
can bewalked on
after 1 h
can bewalked on
after 1 h
can bewalked on
after 1 h
can bewalked on
after 1 h
After 1 h
After
4 hAfter
1 h
PROTECTION
Indoors
FILACLEANERdiluted: 1:200
coverage: 1500 m2/1L
ORDINARY
MAINTENANCE
FILACLEANERdiluted: 1:30
coverage: 50 m2/1L
one coat of yourchosen finishing wax
EXTRAORDINARY
The expert’s advice: pre-treat with FILAPRW200To protect material from grouting dirt and facilitate cleaning after laying, pre-treat the surface with a coat of pre-grouting protector FILAPRW200 (pure; coverage: for terracotta 8/10 m2, for stone 10/20 m2 per liter)
Verticalsurfaces
Horizontal surfaces
FILAPT10pure o diluted 1:1coverage: 10-20 m2/1L2 coats, 2nd coat after 3 h
COLOUR ENHANCING AGAINST STAINS
on dry surface,can bewalked on
WARNING:to remove FILAPT10 in the event of incorrect application or when deep-down cleaning is required, use the FILANOPAINT STAR cleaner.
21
* for restoring tratment apply a single coat of the last protective product used.
NATURAL STONES High absorbencyMatt or unpolished finish(Unpolished limestone, Vicenza stone, Lecce stone, Pietra Serena, Split-Finish Quartz)
on dry surface,can bewalked on
on dry surface,can bewalked on
NATURAL EFFECT AGAINST STAINS
FILAW68*purecoverage: 10 m2/1L2 coats (no interval)
WET LOOkAGAINST STAINS
FILAPT10*pure o diluted 1:1coverage: 10-20 m2/1L2 coats, 2nd coat after 3 h
PROTECTION
Outdoors
FILAPS87diluted 1:5coverage: 20 m2/1L
RESTORING PROTECTION
RESTORINGWASH TO REMOvEGRAFFITI AND SMOG
FILANOPAINT STARpurecoverage: 5 m2/1L
WASH
FILACLEANERdiluted 1:30coverage: 50 m2/1L
AFTER LAYING
on drysurface
on drysurface
on drysurface
FILACLEANERdiluted: 1:200
coverage: 1500 m2/1L
ORDINARY
MAINTENANCE
FILAPS87diluted: 1:10
coverage: 100 m2/1L
EXTRAORDINARY
The expert’s advice: pre-treat with FILAPRW200To protect material from grouting dirt and facilitate cleaning after laying, pre-treat the surface with a coat of pre-grouting protector FILAPRW200 (pure; coverage: for terracotta 8/10 m2, for stone 10/20 m2 per liter)
Verticalsurfaces
Horizontal surfaces
WARNING:to remove FILAPT10 in the event of incorrect application or when deep-down cleaning is required, use the FILANOPAINT STAR cleaner.
22
NATURAL STONESCobblestones, tumbled or sand-blasted marbleSOLVENT-BASED PRODUCTS
PROTECTION
Indoors
RESTORINGFINISHES
FILAPS87diluted 1:5coverage: 30 m2/1L
on dry surface
WASH
RESTORINGPROTECTION
FILACLEANERdiluted 1:30coverage: 50 m2/1L
on drysurface
DETERDEkdiluted 1:5coverage: 20 m2/1L
AFTER LAYING
on drysurface
FINISHING
FILAMATTpurecoverage: 30-40 m2/1L2 coats, 2nd coat after 1 h
FILALONGLIFEpurecoverage: 30-40 m2/1L2 coats, 2nd coat after 1 h
SHINYEFFECT
NATURALEFFECT
can bewalked onafter 1 h
FILASATINpurecoverage: 30-40 m2/1L2 coats, 2nd coat after 1 h
SATINEFFECT
can bewalked onafter 1 h
can bewalked onafter 1 h
FILACLEANERdiluted: 1:200
coverage: 1500 m2/1L
ORDINARY
MAINTENANCE
FILACLEANERdiluted: 1:30
coverage: 50 m2/1L
one coat of your chosenfinishing wax
EXTRAORDINARY
The expert’s advice: pre-treat with FILAPRW200To protect material from grouting dirt and facilitate cleaning after laying, pre-treat the surface with a coat of pre-grouting protector FILAPRW200 (pure; coverage: for terracotta 8/10 m2, for stone 10/20 m2 per liter)
NATURAL EFFECT AGAINST STAINS
FILAFOBpurecoverage: 20 m2/1L1 coat
After
24 h
* for restoring tratment apply a single coat of the last protective product used.
Verticalsurfaces
Horizontal surfaces
WARNING:to be used onlyon acid-resistant stones
FILASTONE PLUS*purecoverage: 20 m2/1L2 coats, 2nd coat after 8 h
COLOUR-ENHANCING AGAINST STAINS
can bewalked on
after 8 h
WARNING: remove any excess during the application as mentioned in the product label.
WET LOOkAGAINST STAINS
FILAWET*purecoverage: 20 m2/1L2 coats, 2nd coat after 24 h
on dry surface,can bewalked on
WARNING: to remove FILAWET in the event of incorrect application or when deep-down cleaning is required, use the FILANOPAINT STAR cleaner.
NATURAL STONESCobblestones, tumbled or sand-blasted marbleWATER-BASED PRODUCTS
The expert’s advice: pre-treat with FILAPRW200To protect material from grouting dirt and facilitate cleaning after laying, pre-treat the surface with a coat of pre-grouting protector FILAPRW200 (pure; coverage: for terracotta 8/10 m2, for stone 10/20 m2 per liter)
WASH
RESTORINGFINISHES
PROTECTION
RESTORINGPROTECTION
DETERDEkdiluted 1:5coverage: 20 m2/1L
AFTER LAYING
on drysurface
on drysurface
FILACLEANERdiluted: 1:200
coverage: 1500 m2/1L
ORDINARY
MAINTENANCE
FILAPS87diluted: 1:10
coverage: 100 m2/1L
EXTRAORDINARY
* for restoring tratment apply a single coat of the last protective product used.
Verticalsurfaces
Horizontal surfaces
WARNING:to be used onlyon acid-resistant stones
FILACLEANERdiluted 1:30coverage: 50 m2/1L
23
Indoors
FILAPS87diluted 1:5coverage: 30 m2/1L
on dry surface
FINISHING
FILAMATTpurecoverage: 30-40 m2/1L2 coats, 2nd coat after 1 h
FILALONGLIFEpurecoverage: 30-40 m2/1L2 coats, 2nd coat after 1 h
SHINYEFFECT
NATURALEFFECT
can bewalked onafter 1 h
FILASATINpurecoverage: 30-40 m2/1L2 coats, 2nd coat after 1 h
SATINEFFECT
can bewalked onafter 1 h
can bewalked onafter 1 h
WARNING: to remove FILAWET in the event of incorrect application or when deep-down cleaning is required, use the FILANOPAINT STAR cleaner.
FILAPT10*diluted 1:1coverage: 30-40 m2/1L2 coats, 2nd coat after 3 h
FILAMP90 ECO PLUSpurecoverage: 20 m2/1L1 coat working completely into the material
WET LOOkAGAINST STAINS
NATURAL EFFECT AGAINST STAINS
on dry surface,can bewalked on
WARNING:before the product dries, remove any residue.
After
4 h
24
The expert’s advice: pre-treat with FILAPRW200To protect material from grouting dirt and facilitate cleaning after laying, pre-treat the surface with a coat of pre-grouting protector FILAPRW200 (pure; coverage: for terracotta 8/10 m2, for stone 10/20 m2 per liter)
WASH
HYDROREPpurecoverage: 20 m2/1L 1 coat
HYDROREPpurecoverage: 20 m2/1L 1 coat
FILAFOB*purecoverage: 20 m2/1L1 coat
FILASTONE PLUS*purecoverage: 20 m2/1L1 or 2 coats, 2nd coat after 8 h
FILAPS87diluted 1:5coverage: 30 m2/1L
RESTORINGWASH TO REMOvEGRAFFITI AND SMOG
FILANOPAINT STARpurecoverage: 5 m2/1L
NATURAL EFFECT AGAINST STAINS
WET LOOkAGAINST STAINS
FILAWET*purecoverage: 20 m2/1L2 coats, 2nd coat after 24 h
COLOUR-ENHANCING AGAINST STAINS
WATER REPELLENT
WATER REPELLENT
PROTECTION
RESTORINGPROTECTION
DETERDEkdiluted 1:5coverage: 20 m2/1L
AFTER LAYING on dry surface,can bewalked on
on dry surface,can bewalked on
After 24 h
can bewalked onafter 8 h
on dry surface,can bewalked on
on drysurface
on drysurface
on drysurface
WARNING: to remove FILAWET in the event of incorrect application or when deep-down cleaning is required, use the FILANOPAINT STAR cleaner.
WARNING: remove any excess during the application as mentioned in the product label.
FILACLEANERdiluted: 1:200
coverage: 1500 m2/1L
ORDINARY
MAINTENANCE
FILAPS87diluted: 1:10
coverage: 100 m2/1L
EXTRAORDINARY
* for restoring tratment apply a single coat of the last protective product used.
WARNING:to be used onlyon acid-resistant stones
NATURAL STONESCobblestones, tumbled or sand-blasted marbleSOLVENT-BASED PRODUCTS
Verticalsurfaces
Horizontal surfaces
Outdoors
25
NATURAL STONESCobblestones, tumbled or sand-blasted marbleWATER-BASED PRODUCTS
The expert’s advice: pre-treat with FILAPRW200To protect material from grouting dirt and facilitate cleaning after laying, pre-treat the surface with a coat of pre-grouting protector FILAPRW200 (pure; coverage: for terracotta 8/10 m2, for stone 10/20 m2 per liter)
WASH
FILAPS87diluted 1:5coverage: 30 m2/1L
RESTORINGWASH TO REMOvEGRAFFITI AND SMOG
FILANOPAINT STARpurecoverage: 5 m2/1L
PROTECTION
RESTORINGPROTECTION
DETERDEkdiluted 1:5coverage: 20 m2/1L
AFTER LAYINGon dry surface,can bewalked on
on drysurface
on drysurface
on drysurface
FILACLEANERdiluted: 1:200
coverage: 1500 m2/1L
ORDINARY
MAINTENANCE
FILAPS87diluted: 1:10
coverage: 100 m2/1L
EXTRAORDINARY
Outdoors
* for restoring tratment apply a single coat of the last protective product used.
Verticalsurfaces
Horizontal surfaces
WARNING:to be used onlyon acid-resistant stones
WARNING: to remove FILAWET in the event of incorrect application or when deep-down cleaning is required, use the FILANOPAINT STAR cleaner.
FILAPT10*diluted 1:1coverage: 30-40 m2/1L2 coats, 2nd coat after 3 h
FILAMP90 ECO PLUSpurecoverage: 20 m2/1L1 coat working completely into the material
WET LOOkAGAINST STAINS
NATURAL EFFECT AGAINST STAINS
on dry surface,can bewalked on
WARNING:before the product dries, remove any residue.
26
NATURAL STONESPolished or brushed finish(Marble, Travertine, Granite, Limestone)
FILAMP90purecoverage: 30 m2/1L1 coat
RESTORING THE GLOSS
FILAPS87diluted 1:5coverage: 30 m2/1L
NATURAL EFFECT AGAINST STAINSSOLvENT BASED
FILACLEANERdiluted 1:30coverage: 50 m2/1L
RESTORINGPROTECTION
FILACLEANERdiluted 1:30coverage: 50 m2/1L
AFTER LAYING
WASH
on dry surface
on dry surface
on dry surface
After 24 h, when the floor is dry, remove the excess using a cloth dipped in the product, then wipe with a dry cloth or absorbent paper
After 4 h, when the floor is dry, remove the excess using a cloth dipped in the product, then wipe with a dry cloth or absorbent paper
PROTECTIONFINISHING
FILASATINpurecoverage: 30-50 m2/1L1 coat
SATIN EFFECT
Polishing
After 1 h
Indoors
FILASTONE PLUSpurecoverage: 30 m2/1L1 coat
COLOUR-ENHANCING AGAINST STAINSSOLvENT BASED
can bewalked onafter 8 h
WARNING: remove any excess during the application as mentioned in the product label.
FILAMP90 ECO PLUSpurecoverage: 30 m2/1L1 coat
NATURAL EFFECT AGAINST STAINSWATER BASED
on dry surface,can bewalked on
on dry surface,can bewalked on
FILACLEANERdiluted: 1:200
coverage: 1500 m2/1L
ORDINARY
MAINTENANCE
FILACLEANERdiluted: 1:30
coverage: 50 m2/1L
one coat of yourchosen finishing wax
EXTRAORDINARY
FILAkRISTALLPLUSpurecoverage: 50 m2/1L1 or more applications
SHINY EFFECT(PROFESSIONAL USE)
WARNING: do not use on non-calcareous stones such as granite, quartzite and sandstone.
on dry surface,can bewalked on
FILACLASSICpurecoverage: 30-50 m2/1L1 coat
SHINY EFFECT
Polishing
After 1 h
Verticalsurfaces
Horizontal surfaces
27
MANUFACTURED STONE
FILAPS87diluted 1:5coverage: 30 m2/1L
FILAPS87diluted 1:5coverage: 30 m2/1L
FILAFOBpurecoverage: 20 m2/1L1 coat
RESTORINGFINISHES
NATURAL EFFECT
FILAMATTpurecoverage: 30-40 m2/1L2 coats, 2nd coat after 1 h
SATIN EFFECT
FILASATINpurecoverage: 30-40 m2/1L2 coats, 2nd coat after 1 h
WASH
FINISHING
NATURAL EFFECT AGAINST STAINSSOLvENT BASED
PROTECTION
on drysurface
on drysurface
AFTER LAYING
can bewalked onafter 1 h
can bewalked onafter 1 h
After 24 h
ORDINARY
FILACLEANERdiluted: 1:200
coverage: 1500 m2/1L
MAINTENANCE
EXTRAORDINARY
FILACLEANERdiluted: 1:30
coverage: 50 m2/1L
Indoors
The expert’s advice: pre-treat with FILAPRW200To protect material from grouting dirt and facilitate cleaning after laying, pre-treat the surface with a coat of pre-grouting protector FILAPRW200 (pure; coverage: for terracotta 8/10 m2, for stone 10/20 m2 per liter)
FILAMP90 ECO PLUSpurecoverage: 20 m2/1L1 coat working completely into the material
NATURAL EFFECT AGAINST STAINSWATER BASED
on dry surface,can bewalked on
WARNING: before the product dries, remove any residue.
Horizontal surfaces
28
MANUFACTURED STONE
MANUFACTURED STONEVerticalsurfaces
Outdoors
HYDROREP*purecoverage: 20 m2/1L2 coats, 2nd coat after 24 h
WATER REPELLENT
PROTECTION
FILAPS87diluted 1:5coverage: 30 m2/1L
FILAPS87diluted 1:5coverage: 30 m2/1L
RESTORINGPROTECTION
WASH
AFTER LAYING
on dry surface,can bewalked on
ORDINARY
FILACLEANERdiluted: 1:200
coverage: 1500 m2/1L
EXTRAORDINARY
FILAPS87diluted: 1:10
coverage: 100 m2/1L
MAINTENANCE
on drysurface
* for restoring tratment apply a single coat of the last protective product used.
FINISHING
Indoors
FILAPS87diluted 1:5coverage: 30 m2/1L
FILAPS87diluted 1:5coverage: 30 m2/1L
RESTORINGFINISHES
ANTI-DUST TREATMENT, NATURAL EFFECT
FILAMATTpurecoverage: 30-40 m2/1L2 coats, 2nd coat after 1 h
WASH
on drysurface
AFTER LAYING
the surfaceis readyafter 1 h
ORDINARY
FILACLEANERdiluted: 1:200
coverage: 1500 m2/1L
FILABRIOready to use
MAINTENANCE
The expert’s advice: pre-treat with FILAPRW200To protect material from grouting dirt and facilitate cleaning after laying, pre-treat the surface with a coat of pre-grouting protector FILAPRW200 (pure; coverage: for terracotta 8/10 m2, for stone 10/20 m2 per liter)
Verticalsurfaces
The expert’s advice:pre-treat with FILAPRW200To protect material from grouting dirt and facilitate cleaning after laying, pre-treat the surface with a coat of pre-grouting protector FILAPRW200 (pure; coverage: for terracotta 8/10 m2, for stone 10/20 m2 per liter)
29
MANUFACTURED STONEOutdoors
FILAPS87diluted 1:5coverage: 30 m2/1L
FILAPS87diluted 1:5coverage: 30 m2/1L
RESTORINGPROTECTION
WASHAFTER LAYING
HYDROREP*purecoverage: 20 m2/1L2 coats, 2nd coat after 24 h
WATER REPELLENTSOLvENT BASED
HYDROREPpurecoverage: 20 m2/1L1 coat
WATER REPELLENTSOLvENT BASED
FILAFOB*purecoverage: 20 m2/1L1 coat
NATURAL EFFECT AGAINST STAINSSOLvENT BASED
on dry surface,can bewalked on
on dry surface,can bewalked on
on dry surface, choose from:
on dry surface, choose from:
After 24 h
ORDINARY
FILACLEANERdiluted: 1:200
coverage: 1500 m2/1L
EXTRAORDINARY
FILAPS87diluted: 1:10
coverage: 100 m2/1L
MAINTENANCEPROTECTION
FILAMP90 ECO PLUSpurecoverage: 20 m2/1L1 coat working completely into the material
NATURAL EFFECTAGAINST STAINSWATER BASED
on dry surface,can bewalked on
WARNING: before the product dries, remove any residue.
The expert’s advice: pre-treat with FILAPRW200To protect material from grouting dirt and facilitate cleaning after laying, pre-treat the surface with a coat of pre-grouting protector FILAPRW200 (pure; coverage: for terracotta 8/10 m2, for stone 10/20 m2 per liter)
* for restoring tratment apply a single coat of the last protective product used.
Horizontal surfaces
30
UNPOLISHED AGGLOMERATES Rustic terrazzo, Marble concrete
HYDROREP*purecoverage: 10 m2/1L2 coats, 2nd coat after 24 h
NATURAL EFFECT AGAINST STAINS
WATER REPELLENT
FILAFOB*purecoverage: 10 m2/1L2 coats, 2nd coat after 24 h
WET LOOkAGAINST STAINS
FILAWET*purecoverage: 10 m2/1L2 or 3 coats (24 h interval)
PROTECTIONWASH
FILAPS87diluted 1:5coverage: 20 m2/1L
FILAPS87diluted 1:5coverage: 20 m2/1L
FILANOPAINT STARpurecoverage: 5 m2/1L
RESTORINGPROTECTION
RESTORINGWASH TO REMOvEGRAFFITI AND SMOG
AFTER LAYING
on drysurface
on drysurface
on drysurface
on dry surface,can bewalked on
on dry surface,can bewalked on
on dry surface,can bewalked on
WARNING: to remove FILAWET in the event of incorrect application or when deep-down cleaning is required, use the FILANOPAINT STAR cleaner.
Outdoors
ORDINARY
FILACLEANERdiluted: 1:200
coverage: 1500 m2/1L
EXTRAORDINARY
FILAPS87diluted: 1:10
coverage: 100 m2/1L
MAINTENANCE
* for restoring tratment apply a single coat of the last protective product used.
WATER-BASED ALTERNATIvE PROTECTION
FILAPT10*pure o diluted 1:1coverage: 10-20 m2/1L2 coats, 2nd coat after 3 h
FILAW68*purecoverage: 10 m2/1L2 coats (no interval)
WET LOOkAGAINST STAINS
NATURAL EFFECT AGAINST STAINS
on dry surface,can bewalked on
on dry surface,can bewalked on
The expert’s advice: pre-treat with FILAPRW200To protect material from grouting dirt and facilitate cleaning after laying, pre-treat the surface with a coat of pre-grouting protector FILAPRW200 (pure; coverage: for terracotta 8/10 m2, for stone 10/20 m2 per liter)
Verticalsurfaces
Horizontal surfaces
31
WASH
POLISHED AGGLOMERATES Venetian Terrazzo
Indoors
FILAMP90 ECO PLUSpurecoverage: 20 m2/1L1 coat
NATURAL EFFECT AGAINST STAINSWATER BASED
RESTORINGTHE GLOSS
FILAPS87diluted 1:5coverage: 20 m2/1L
on drysurface
FILACLEANERdiluted 1:30coverage: 50 m2/1L
AFTER LAYING
on drysurface
NATURAL EFFECT AGAINST STAINSSOLvENT BASED
FILAMP90purecoverage: 20 m2/1L1 or 2 coats, 2nd coat after 24 h
on dry surface,can bewalked on
on dry surface,can bewalked on
FINISHING
FILACLEANERdiluted: 1:200
coverage: 1500 m2/1L
ORDINARY
MAINTENANCE
FILACLEANERdiluted: 1:30
coverage: 50 m2/1L
one coat of yourchosen finishing wax
EXTRAORDINARY
FILAkRISTALLPLUSpurecoverage: 50 m2/1L1 or more applications
SHINY EFFECT(PROFESSIONAL USE)
on dry surface,can bewalked on
After 24 h, when the floor is dry, remove the excess using a cloth dipped in the product, then wipe with a dry cloth or absorbent paper
After 4 h, when the floor is dry, remove the excess using a cloth dipped in the product, then wipe with a dry cloth or absorbent paper
PROTECTION
FILACLASSICpurecoverage: 30-50 m2/1L1 coat
SHINY EFFECT
Polishing
After 1 h
Horizontal surfaces
32
WASH
FILAMP90purecoverage: 30 m2/1L1 coat
NATURAL EFFECT AGAINST STAINSSOLvENT BASED
After 24 h, when the floor is dry, remove the excess using a cloth dipped in the product, then wipe with a dry cloth or absorbent paper
PROTECTION
FILASTONE PLUSpurecoverage: 30-50 m2/1L1 coat
COLOUR-ENHANCING AGAINST STAINSSOLvENT BASED
can bewalked on
after 8 h
WARNING: remove any excess during the application as mentioned in the product label.
FILAMP90 ECO PLUSpurecoverage: 30 m2/1L1 coat
NATURAL EFFECT AGAINST STAINSWATER BASED
on dry surface,can bewalked on
on dry surface,can bewalked on
RESTORINGTHE GLOSS
FILAPS87diluted 1:10coverage: 100 m2/1L
on drysurface
FILACLEANERdiluted 1:10coverage: 20 m2/1L
AFTER LAYING
on drysurface
FINISHING
FILACLASSICdiluted 1:2coverage: 60-80 m2/1L1 coat
SHINY EFFECT
Polishing
After 1 h
POLISHED AGGLOMERATES Marble/Resin, Quartz/Granite/Resin
Indoors
FILAkRISTALLPLUSpurecoverage: 50 m2/1L1 coat
SHINY EFFECT(PROFESSIONAL USE)
WARNING: to be used only on marble/resin surfaces
on dry surface,can bewalked on
After 4 h, when the floor is dry, remove the excess using a cloth dipped in the product, then wipe with a dry cloth or absorbent paper
Horizontal surfaces
FILACLEANERdiluted: 1:200
coverage: 1500 m2/1L
ORDINARY
MAINTENANCE
one coat of yourchosen finishing wax
EXTRAORDINARY
FILAPS87diluted: 1:10
coverage: 100 m2/1L
FILAREFRESHready to use
33
WASH PROTECTION
FILAMP90 ECO PLUSpurecoverage: 20 m2/1L1 coat
NATURAL EFFECT AGAINST STAINSWATER BASED
RESTORINGTHE GLOSS
FILAPS87diluted 1:5coverage: 20 m2/1L
on drysurface
FILACLEANERdiluted 1:30coverage: 50 m2/1L
AFTER LAYING
on drysurface
NATURAL EFFECT AGAINST STAINSSOLvENT BASED
FILAFOBpurecoverage: 20 m2/1L1 coat
on dry surface,can bewalked on
on dry surface,can bewalked on
FINISHING
FILACLEANERdiluted: 1:200
coverage: 1500 m2/1L
ORDINARY
MAINTENANCE
FILACLEANERdiluted: 1:30
coverage: 50 m2/1L
one coat of yourchosen finishing wax
EXTRAORDINARY
FILAkRISTALLPLUSpurecoverage: 50 m2/1L1 or more applications
SHINY EFFECT(PROFESSIONAL USE)
on dry surface,can bewalked on
After 24 h, when the floor is dry, remove the excess using a cloth dipped in the product, then wipe with a dry cloth or absorbent paper
POLISHED AGGLOMERATES Terrazzo
Indoors
After 4 h, when the floor is dry, remove the excess using a cloth dipped in the product, then wipe with a dry cloth or absorbent paper
FILACLASSICpurecoverage: 30-50 m2/1L1 coat
SHINY EFFECT
Polishing
After 1 h
Horizontal surfaces
34
ENAMELLEDCERAMIC TILES
WASH
WARNING:check the resistance of the material to the product before use
DETERDEkdiluted 1:5coverage: 40 m2/1L
AFTER LAYING(CONCRETE GROUT)
on dry surface,can bewalked on
FILACR10purecoverage: up to 10 m2/1L
AFTER LAYING(EPOXY GROUT)
on dry surface,can bewalked on
ORDINARY
FILACLEANERdiluted: 1:200
coverage: 1500 m2/1L
EXTRAORDINARY
FILAPS87diluted: 1:5
coverage: 30 m2/1L
MAINTENANCE
PROTECTION
FILAMP90 ECO PLUSpurecoverage: 30-40 m2/1L1 coat
NATURAL EFFECT AGAINST STAINSWATER BASED
WASH
RESTORINGPROTECTION
FILAPS87diluted 1:5coverage: 30 m2/1L
DETERDEkdiluted 1:5coverage: 40 m2/1L
AFTER LAYING(CONCRETE GROUT)
on drysurface
on drysurface
on drysurface
NATURAL EFFECT AGAINST STAINSSOLvENT BASED
FILAMP90purecoverage: 30-40 m2/1L1 coat
on dry surface,can bewalked on
on dry surface,can bewalked on
After 24 h, when the floor is dry, remove the excess using a cloth dipped in the product, then wipe with a dry cloth or absorbent paper
FILACR10purecoverage: up to 10 m2/1L
AFTER LAYING(EPOXY GROUT)
FILACLEANERdiluted: 1:200
coverage: 1500 m2/1L
FILABRIOready to use
ORDINARY
MAINTENANCE
EXTRAORDINARY
FILACLEANERdiluted: 1:30
coverage: 50 m2/1L
POLISHED PORCELAIN
Indoors
After 4 h, when the floor is dry, remove the excess using a cloth dipped in the product, then wipe with a dry cloth or absorbent paper
IndoorsOutdoors
Verticalsurfaces
Horizontal surfaces
Verticalsurfaces
Horizontal surfaces
35
LAPPATO PORCELAIN
PROTECTIONWASH
RESTORINGPROTECTION
FILAPS87diluted 1:5coverage: 30 m2/1L
DETERDEkdiluted 1:5coverage: 40 m2/1L
AFTER LAYING(CONCRETE GROUT)
on drysurface
on drysurface
on drysurface
AGAINST DIRTAND STAINS
FILAPD15purecoverage: 70 m2/1L1 coat
can bewalked onafter 8 h
WARNING:within 10 minutes from application, rub with asponge, cotton cloth or single-brush machine (white disc), to help the product penetrate and completely remove any residue.
FILACR10purecoverage: up to 10 m2/1L
AFTER LAYING(EPOXY GROUT)
IndoorsOutdoors
WARNING:check adhesion of the product on a small area before use
ORDINARY
FILACLEANERdiluted: 1:200
coverage: 1500 m2/1L
EXTRAORDINARY
FILAPS87diluted: 1:5
coverage: 30 m2/1L
MAINTENANCE
Verticalsurfaces
Horizontal surfaces
36
TEXTURED PORCELAINNATURAL PORCELAIN
PROTECTION
WASH
RESTORINGPROTECTION
FILAPS87diluted 1:5coverage: 30 m2/1L
DETERDEkdiluted 1:5coverage: 40 m2/1L
AFTER LAYING(CONCRETE GROUT)
on drysurface
on drysurface
on drysurface
AGAINST DIRTWATER BASED(ONLY FOR INDOORS TEXTUREDPORCELAIN SURFACES)
AGAINST DIRTSOLvENT BASED
FILAJETpurecoverage: 30-40 m2/1L1 or 2 coats 2nd coat after 1h
FILASTOP DIRTpurecoverage: 30-40 m2/1L1 coat
can bewalked onafter 2-3 h
can bewalked onafter 8 h
FILACR10purecoverage: up to 10 m2/1L
AFTER LAYING(EPOXY GROUT)
WARNING:check adhesion of the producton a small area before use
WARNING:within 10 minutes from application, rub with asponge, cotton cloth or single-brush machine (white disc), to help the product penetrate and completely remove any residue.
ORDINARY
FILACLEANERdiluted: 1:200
coverage: 1500 m2/1L
MAINTENANCE
EXTRAORDINARY
FILACLEANERdiluted: 1:30
coverage: 50 m2/1L
IndoorsOutdoors
Verticalsurfaces
Horizontal surfaces
37
CRACkLE-GLAzECERAMIC TILES
Indoors
PROTECTION
FILAMP90 ECO PLUSpurecoverage: 30-40 m2/1L1 coat
NATURAL EFFECT AGAINST STAINSWATER BASED
WASH
AFTER LAYING
on drysurface
on drysurface
NATURAL EFFECT AGAINST STAINSSOLvENT BASED
FILAMP90purecoverage: 30-40 m2/1L1 coat
on dry surface,can bewalked on
on dry surface,can bewalked on
After 24 h, when the floor is dry, remove the excess using a cloth dipped in the product, then wipe with a dry cloth or absorbent paper
RESTORINGPROTECTION
FILACLEANERdiluted: 1:200
coverage: 1500 m2/1L
FILABRIOready to use
ORDINARY
MAINTENANCE
EXTRAORDINARY
FILACLEANERdiluted: 1:30
coverage: 50 m2/1L
FILACLEANERdiluted 1:30coverage: 50 m2/1L
FILACLEANERdiluted 1:30coverage: 50 m2/1L
After 4 h, when the floor is dry, remove the excess using a cloth dipped in the product, then wipe with a dry cloth or absorbent paper
Verticalsurfaces
Horizontal surfaces
38
TERRACOTTAtreatment with WATER-BASED PRODUCTS
NATURAL EFFECT AGAINST STAINS
FILAPS87diluted 1:5coverage: 20 m2/1L
FILAJETpurecoverage: 30 m2/1L1 coat
on drysurface
DETERDEkdiluted 1:5coverage: 20 m2/1L
WET LOOkAGAINST STAINS
FILAPT10purecoverage: 7-20 m2/1L2 coats, 2nd coat after 3 h
FILAW68purecoverage: 7-20 m2/1L1 coat
AFTER LAYING
WASH
RestoRingpRotection
AGAINST DIRT
AGAINST DIRT
FILAJETpurecoverage: 30 m2/1L1 coat
After 4 h
After 1 h
After 1 h
PROTECTION
The expert’s advice: pre-treat with FILAPRW200To protect material from grouting dirt and facilitate cleaning after laying, pre-treat the surface with a coat of pre-grouting protector FILAPRW200 (pure; coverage: for terracotta 8/10 m2, for stone 10/20 m2 per liter)
FINISHING
FILALONGLIFEpurecoverage: 30 m2/1L1 coat
SHINY EFFECT
FILAMATTpurecoverage: 30 m2/1L1 coat
FILASATINpurecoverage: 30 m2/1L1 coat
SATINEFFECT
FILACLASSICpurecoverage: 30 m2/1L1 coat
SHINY EFFECT
NATURAL EFFECT
can bewalked on
after 1 h
can bewalked on
after 1 h
can bewalked on
after 1 h
can bewalked on
after 1 h
FILACLEANERdiluted: 1:200
coverage: 1500 m2/1L
ORDINARY
MAINTENANCE
FILACLEANERdiluted: 1:30
coverage: 50 m2/1L
on dry surface, apply one coat of your chosen
finishing wax
EXTRAORDINARY
Indoors
after
7-15 days
on dry surface,can bewalked on
Horizontal surfaces
WARNING:to remove FILAPT10 in the event of incorrect application or when deep-down cleaning is required, use the FILANOPAINT STAR cleaner.
39
PROTECTION
DETERDEkdiluted 1:5coverage: 20 m2/1L
WASH
* choose FILANATURWAX in the desired colour.
For maintenance treatment apply just 1 coat of product.
FILAPS87diluted 1:5coverage: 20 m2/1L
FILAFOBpurecoverage: 5-20 m2/1L1 coat
FILASOLvpurecoverage: 5 m2/1L
FILAMAXdiluted from 1:1 to 1: 5coverage: 5-20 m2/1L
for manual intervention
for professionalinterventionwith single brushmachine
AFTER LAYING
STRONGERRESTORING FOR SOLID WAXES
RestoRingpRotection
After 24 h
on drysurface
FILANATURWAX*purecoverage: 20 m2/1L2 coats, 2nd coat after 8 h
after
Polishing
COLOURENHANCING AGAINST STAINS
ANTI STAIN
TERRACOTTAtreatment with SOLVENT-BASED PRODUCTS
FINISHING
FILALONGLIFEpurecoverage: 30 m2/1L1 coat
SHINY EFFECT
FILAMATTpurecoverage: 30 m2/1L1 coat
FILASATINpurecoverage: 30 m2/1L1 coat
SATINEFFECT
FILACLASSICpurecoverage: 30 m2/1L1 coat
SHINY EFFECT
NATURAL EFFECT
can bewalked on
after 1 h
can bewalked on
after 1 h
can bewalked on
after 1 h
can bewalked on
after 1 h
FILACLEANERdiluted: 1:200
coverage: 1500 m2/1L
ORDINARY
MAINTENANCE
Indoors
The expert’s advice:pre-treat with FILAPRW200To protect material from grouting dirt and facilitate cleaning after laying, pre-treat the surface with a coat of pre-grouting protector FILAPRW200 (pure; coverage: for terracotta 8/10 m2, for stone 10/20 m2 per liter)
after
7-15 days
Horizontal surfaces
After 8 h FILACLEANER
diluted: 1:30coverage: 50 m2/1L
on dry surface, apply one coat of your chosen
finishing wax
EXTRAORDINARY
40
TERRACOTTAtreatment with WATER-BASED PRODUCTS
* for restoring tratment apply a single coat of the last protective product used.
The expert’s advice: pre-treat with FILAPRW200To protect material from grouting dirt and facilitate cleaning after laying, pre-treat the surface with a coat of pre-grouting protector FILAPRW200 (pure; coverage: for terracotta 8/10 m2, for stone 10/20 m2 per liter)
FILAPS87diluted 1:5coverage: 20 m2/1L
FILANOPAINT STARpurecoverage: 5 m2/1L
DETERDEkdiluted 1:5coverage: 20 m2/1L
FILAPHzEROdiluted 1:5coverage: 20 m2/1L
AFTER LAYING
STRONGERAFTER LAYING
WASH
RESTORINGPROTECTION
RESTORING WASHTO REMOvE GRAFFITIAND SMOG
on drysurface
on drysurface
after
7-15 days
after
7-15 days
FILAW68*purecoverage: 7-20 m2/1L2 coats (no interval)
FILAPT10*purecoverage: 7-20 m2/1L2 coats, 2nd coat after 3 h
NATURAL EFFECT AGAINST STAINS
WET LOOkAGAINST STAINS
on dry surface,can bewalked on
on dry surface,can bewalked on
PROTECTION
FILACLEANERdiluted: 1:200
coverage: 1500 m2/1L
ORDINARY
MAINTENANCE
FILAPS87diluted: 1:10
coverage: 100 m2/1L
EXTRAORDINARY
Outdoors
WARNING:to remove FILAPT10 in the event of incorrect application or when deep-down cleaning is required, use the FILANOPAINT STAR cleaner.
Horizontal surfaces
41
TERRACOTTA / UNGLAZED QUARRY TILEStreatment with SOLVENT-BASED PRODUCTS
Outdoors
* for restoring tratment apply a single coat of the last protective product used.
The expert’s advice: pre-treat with FILAPRW200To protect material from grouting dirt and facilitate cleaning after laying, pre-treat the surface with a coat of pre-grouting protector FILAPRW200 (pure; coverage: for terracotta 8/10 m2, for stone 10/20 m2 per liter)
FILAPS87diluted 1:5coverage: 20 m2/1L
FILAPHzEROdiluted 1:5coverage: 20 m2/1L
AFTER LAYING
STRONGERAFTER LAYING
WASH
RESTORINGPROTECTION
on drysurface
NATURAL EFFECT AGAINST STAINS
FILAFOB*purecoverage: 5-20 m2/1L1 coat
on dry surface,can bewalked on
PROTECTION
FILACLEANERdiluted: 1:200
coverage: 1500 m2/1L
ORDINARY
MAINTENANCE
FILAPS87diluted: 1:10
coverage: 100 m2/1L
EXTRAORDINARY
DETERDEkdiluted 1:5coverage: 20 m2/1L
after
7-15 days
after
7-15 days
Horizontal surfaces
FILANOPAINT STARpurecoverage: 5 m2/1L
RESTORING WASHTO REMOvE GRAFFITIAND SMOG
on drysurface
42
UNGLAzEDQUARRY TILES
* for restoring tratment apply a single coat of the last protective product used.
The expert’s advice: pre-treat with FILAPRW200To protect material from grouting dirt and facilitate cleaning after laying, pre-treat the surface with a coat of pre-grouting protector FILAPRW200 (pure; coverage: for terracotta 8/10 m2, for stone 10/20 m2 per liter)
Indoors
FINISHING
FILAMATT*purecoverage: 30 m2/1L2 coats, 2nd coat after 1 h
FILALONGLIFE*purecoverage: 30 m2/1L2 coats, 2nd coat after 1 h
WASH
SHINY EFFECT
DETERDEkdiluted 1:5coverage: 20 m2/1L
RESTORINGPROTECTION
FILAPS87diluted 1:5coverage: 20 m2/1L
AFTER LAYING
NATURAL EFFECT
on drysurface
on drysurface
on dry surface,can bewalked on
FILASATIN*purecoverage: 30 m2/1L2 coats, 2nd coat after 1 h
SATIN EFFECT
on dry surface,can bewalked on
on dry surface,can bewalked on
FILACLEANERdiluted: 1:200
coverage: 1500 m2/1L
ORDINARY
MAINTENANCE
FILACLEANERdiluted: 1:30
coverage: 50 m2/1L
on dry surface, apply one coat of your chosen
finishing wax
EXTRAORDINARY
Horizontal surfaces
43
* for restoring tratment apply a single coat of the last protective product used.
FINISHING
TERRACOTTABRICkWORk
FILAMATT*purecoverage: 20 m2/1L2 coats, 2nd coat after 1 h
WARNING:for greater water-oil repellence on wall coverings with high stain risk (e.g. kitchen walls) we suggest an under-coat of FILAW68)
FILAPS87diluted 1:5coverage: 20 m2/1L
FILAPHzEROpurecoverage: 5 m2/1L
AFTER LAYING
NATURALEFFECT
WASH
RESTORINGFINISHES
on drysurface
after 1 hthe surface is ready
The expert’s advice: pre-treat with FILAPRW200To protect material from grouting dirt and facilitate cleaning after laying, pre-treat the surface with a coat of pre-grouting protector FILAPRW200 (pure; coverage: for terracotta 8/10 m2, for stone 10/20 m2 per liter)
Indoors
FILACLEANERdiluted: 1:200
coverage: 1500 m2/1L
FILABRIOready to use
ORDINARY
MAINTENANCE
EXTRAORDINARY
FILAPS87diluted: 1:5
coverage: 20 m2/1L
* for restoring tratment apply a single coat of the last protective product used.
on dry surface,apply one coat of wax
Verticalsurfaces
44
TERRACOTTABRICkWORk
AFTER LAYING
RESTORING WASHTO REMOvE SMOG
WASH
RESTORING WASH TO REMOvE GRAFFITI AND SMOG
on drysurface
on drysurface
on drysurface
FILANOPAINT STARpurecoverage: 5 m2/1L
FILAPS87diluted 1:5coverage: 20 m2/1L
DETERDEkpurecoverage: 5 m2/1L
PROTECTION
on dry surface,can bewalked on
FILAW68*purecoverage: 7-10 m2/1L2 coats (no interval)
NATURAL EFFECT AGAINST STAINS AND GRAFFITI
The expert’s advice: pre-treat with FILAPRW200To protect material from grouting dirt and facilitate cleaning after laying, pre-treat the surface with a coat of pre-grouting protector FILAPRW200 (pure; coverage: for terracotta 8/10 m2, for stone 10/20 m2 per liter)
Outdoors
FILACLEANERdiluted: 1:200
coverage: 1500 m2/1L
ORDINARY
MAINTENANCE
FILANOPAINT STARpure
coverage: 5 m2/1L
EXTRAORDINARY
* for restoring tratment apply a single coat of the last protective product used.
Verticalsurfaces
45
ORDINARY
MAINTENANCE
FILACLEANERdiluted: 1:200
coverage: 1500 m2/1L
vARNISHED WOOD
Indoors
Horizontal surfaces
FILAFOBpurecoverage: 10 m2/1L1 coat
FILASATINpurecoverage: 30-40 m2/1L2 coats, 2nd coat after 1 h
DECORATED CONCRETEEncaustic cement tiles
FILACLASSICpurecoverage: 30-40 m2/1L2 coats, 2nd coat after 1 h
FILAPS87diluted 1:5coverage: 20 m2/1L
satin effect
SHINY EFFECT
WASH
RESTORINGFINISHES
NATURAL EFFECT AGAINST STAINSOLvENT BASED
on dry surface, choose from:
on drysurface
FILAPS87diluted 1:5coverage: 20 m2/1L
AFTER LAYING
on drysurface
can bewalked onafter 1 h
can bewalked onafter 1 h
PROTECTION FINISHING
FILACLEANERdiluted: 1:30 - coverage: 50 m2/1L
on dry surface, apply one coat of your chosen finishing wax
ORDINARY
FILACLEANERdiluted: 1:200
coverage: 1500 m2/1L
MAINTENANCE
EXTRAORDINARY
Indoors
FILAMP90 ECO PLUSpurecoverage: 30 m2/1L1 coat working completelyinto the material
NATURAL EFFECT AGAINST STAINSWATER BASED
WARNING: before the product dries,remove any residue.
Horizontal surfaces
after 4 h
46
FILACLEANERdiluted 1:30coverage: 50 m2/1L
AFTER LAYING
WASH
on dry surface:
PROTECTION
AGAINST DIRT
FILALONGLIFEpurecoverage: 50 m2/1L2 coats, 2nd coat after 1 h
can bewalked onafter 1 h
CONCRETE
RESIN FLOORS
Indoors
Indoors
FILABETONpurecoverage: 20-25 m2/1L2 coats, 2nd coat after 4 h
on dry surface,can bewalked on
AGAINST DIRT
PROTECTION
ORDINARY
MAINTENANCE
EXTRAORDINARY
FILACLEANERdiluted: 1:200
coverage: 1500 m2/1L
FILACLEANERdiluted: 1:30
coverage: 50 m2/1L
ORDINARY
MAINTENANCE
EXTRAORDINARY
FILACLEANERdiluted: 1:200
coverage: 1500 m2/1L
FILACLEANERdiluted: 1:30
coverage: 50 m2/1L
WASH
FILAPS87diluted 1:5coverage: 20 m2/1L
RESTORINGPROTECTION
FILAPS87diluted 1:5coverage: 20 m2/1L
AFTER LAYING
on drysurface
Horizontal surfaces
Horizontal surfaces
47
GROUTINGFor protection of grout joints when no other protector has been used
vERY DIRTY JOINTS
WASH
TREATEDJOINTS
NATURAL EFFECT AGAINST STAIN
PROTECTION
on drysurface
DETERDEk*diluted 1:10coverage: 60 m2/1L
FUGANETready to use
FUGAPROOFpurecoverage: 100 m2/1L1 coat
can bewalked onafter 1 h
MAINTENANCE
* WARNING: do not use on shiny marble or in general on acid-sensitive materials. Carry out a preliminary test on ceramic tiles to check their resistance to the product.
IndoorsOutdoors
Verticalsurfaces
Horizontal surfaces
48
What to do if
Candlewax residues pag. 49
Coloured stains (ink, coffee,markers, soft drinks, hair dye,nicotine, fruit juices) pag. 49
Concrete residues and grout pag. 49
Dirty grouting pag. 49
Dull stains (vinegar lemon,Coca Cola, wine, anti-limescaleproduct) pag. 50
Flaking pag. 50
Greasy and oily stains pag. 50
Limescale (stubborn dirt or streaks) pag. 51
Matt surface pag. 52
Mould pag. 52
Paint marks, graffiti pag. 52
Residues of epoxy grouting pag. 52
Rust pag. 53
Salt efflorescences pag. 53
White alcohol, ammonia or bleach stains pag. 53
Residues of glue, chewing gum,adhesive tape, tree resin pag. 53
Residues of silicon and polyurethane foam pag. 53
48
49
PROBLEM MATERIAL CATEGORY REFERENCE PRODUCTS ANSWER
Candle wax residues
- Natural stone
- Terracotta, quarry tiles and bricks
- Porcelain and ceramic tiles
- Wood
FILASOLV,FILAzERO SIL
Wax can be removed by applying pure FILASOLv and rubbing with a green abrasive sponge. Any residue should then be removed using kitchen towel. Surface residues can also be removed using FILAzERO SIL: apply the undiluted product, covering the entire stain. Leave for 20 minutes and then use the spatula provided in the kit. Collect any residue with a soft cloth or kitchen towel. In the event of interior floors treated with wax, restore the finish after cleaning.
Coloured stains (ink, coffee, markers, soft drinks, hair dye, nicotine, fruit juices)
Porcelain and ceramic tiles
FILASR95, FILAPS87 Remove the stains with FILASR95. Pour the product directly onto the stain, leave it to work for about 15 minutes, then remove residues with a damp sponge and rinse with water. If necessary repeat. As an alternative, use FILAPS87 undiluted leaving it to work until completely dry. Wash and rinse the surface.
- Natural stone
- Terracotta, quarry tiles and bricks
FILASR95, FILAPS87 Remove the stains with FILASR95. Pour the product directly onto the stain, leave it to work for about 15 minutes, then remove residues with a damp sponge and rinse with water. If necessary repeat. As an alternative, use FILAPS87 diluted 1:5 with a sponge. Rinse the surface to complete. Restore stain protection treatment with the most suitable product.
Varnished wood
FILACLEANER Use FILACLEANER diluted 1:200 and wipe the surface with a sponge or a clean dry cloth.
Concrete residues and grout
- Natural stone
- Porcelain and ceramic tiles
DETERDEk,FILACLEANER
DETERDEk acid detergent can be used on acid-resistant unpolished stone. For sensitive materials, like marble, travertine and polished agglomerates, it is better to use FILACLEANER neutral detergent.
Terracotta, quarry tiles and bricks
DETERDEk We recommend washing the surface with DETERDEk acid detergent for more stubborn encrusted grout. For dilution and application of both products, read the instructions on the label carefully.
Dirty grouting Porcelain and ceramic tiles
FILAPS87, FUGANET, FUGAPROOF
Floor grouting must be cleaned with FILAPS87, using a flat brush or an abrasive sponge. Rinse thoroughly to complete. For small surfaces and wall coverings we recommend using FUGANET spray detergent. Spray the product on the surface from a distance of about 15-20 cm, rub with an abrasive sponge and then rinse. After cleaning we recommend protecting grouting with FUGAPROOF stain protector.
50
What to do if
Check out filasolutions.com to find the answer to any other questions you might have.
PROBLEM MATERIAL CATEGORY REFERENCE PRODUCTS ANSWER
Dirty grouting Naturalstone
FILAPS87 Grouting of floors and wall coverings in natural stone must be cleaned with FILAPS87, using a flat brush or an abrasive sponge. Rinse thoroughly to complete. Restore stain protection treatment with the most suitable product.
Dull stains (vinegar lemon, Coca Cola, wine, anti-limescale product)
Naturalstone
FILAMARBLE RESTORER, FILAkRISTALL PLUS
Many substances such as vinegar, lemon, Coca Cola, wine, anti-limescale products... are slightly acidic and attack the sheen of marble and of polished natural stone, leaving a dull stain. To restore small surfaces like bathroom and kitchen tops, window sills, etc., we recommend using the FILAMARBLE RESTORER kit. For larger surfaces like floors, we recommend using FILAKRISTALL PLUS.
Flaking - Natural stone
- Terracotta, quarry tiles and bricks
FILAMATT To prevent interior walls giving off dust, a natural-effect wax like FILAMATT can be used, applying two coats directly with a paintbrush.
Greasy and oily stains
- Terracotta, quarry tiles and bricks
- Natural stone
- Concrete and grouting
FILANOSPOT Clean the surface with FILANOSPOT by spraying it directly onto the oily stain. Leave to dry for a few minutes and then remove the white powder that has formed with a brush. Clean with a damp cloth. We recommend restoring the finish of wax-treated floors.
Porcelain and ceramic tiles
FILAPS87 Clean the surface with FILAPS87 diluted 1:5-1:10 and rinse thoroughly.
51
PROBLEM MATERIAL CATEGORY REFERENCE PRODUCTS ANSWER
Greasy and oily stains
Wood FILASOLv The stains can be removed with undiluted FILASOLv, rubbing with a green abrasive sponge and removing residues with kitchen paper. We recommend reapplying the finishing wax on interior floors after cleaning.
Limescale (stubborn dirt or streaks)
Porcelain and ceramic tiles
DETERDEK, FILAVIA BAGNO, FILANO DROPS
In the case of stubborn dirt, we recommend washing with the appropriate dilution of DETERDEk acid detergent and rinsing thoroughly after application. Please follow the instructions on the label carefully. Use FILAvIA BAGNO on marks or limescale residues (e.g. bathrooms, showers). To prevent limescale residues coming back, use FILANO DROPS for ordinary MAINTENANCE.
Naturalstone
DETERDEK,FILACLEANER
Stubborn dirt: DETERDEk acid detergent can be used on acid-resistant unpolished stone. For sensitive materials, like marble, travertine and polished agglomerates, it is better to use FILACLEANER neutral detergent.
Glass,mirrors
FILAVIA BAGNO,FILANO DROPS
We recommend using FILAvIA BAGNO on marks or limescale residues (e.g. bathrooms, showers). To prevent limescale residues coming back, use FILANO DROPS for ordinary maintenance.
Terracotta, quarry tiles and bricks
DETERDEk We recommend washing the surface with DETERDEk acid detergent for more stubborn encrusted grout. For dilution and application of both products please read the instructions on the label carefully.
52
PROBLEM MATERIAL CATEGORY REFERENCE PRODUCTS ANSWER
Matt surface Naturalstone
FILAkRISTALL PLUS, FILACLASSIC, FORMULA MARMO, FILAREFRESH
For floors and large surfaces, shine can be restored using FILAkRISTALL PLUS. Spread the product all over the surface. Once dry, it can be polished with a single-brush machine or machine polisher fitted with special wire wool discs. As an alternative, it is possible to use FILACLASSIC wax, either undiluted or diluted in water, depending on how worn the treatment is. To restore sheen to tops in marble or already treated natural stone, apply FORMULA MARMO polish with a cloth. For ordinary maintenance we recommend cleaning the surface with FILAREFRESH to reinforce stain protection.
Terracotta, quarry tiles and bricks
FILACLASSIC, FILAMATT, FILASATIN, FILALONGLIFE, FILANATURWAX
To restore the finishing with a liquid wax, choosing from FILACLASSIC, FILAMATT, FILASATIN, FILALONGLIFE according to the desired appearance. For traditional treatment with paste wax, apply a coat of FILANATURWAX before the finishing wax.
Mould - Wall paint and marble chip plaster
- Terracotta, quarry tiles and bricks
- Porcelain and ceramic tiles
- Concrete and grouting
- Natural stone
FILAACTIvE1 Spray FILAACTIvE1 directly onto the surface to be cleaned. Leave for about 15 minutes. Rinse with a wet sponge.
Paint marks, graffiti
- Porcelain and ceramic tiles
- Natural stone- Concrete and
plaster - Terracotta,
quarry tiles and bricks
FILANO PAINT STAR, FILAPS87
Apply undiluted FILANOPAINT STAR directly onto the surface, leaving for at least 5 minutes. Use a sponge or cloth and rinse. As an alternative, use FILAPS87 diluted 1:5 following the same instructions. Complete or restore stain protection treatment with the most suitable product.
Residues of epoxy grouting
- Porcelain and ceramic tiles
- Glass mosaic
FILACR10 We recommend using undiluted FILACR10 detergent for epoxy residues, leaving it on the surface for at least 30 minutes. Then rub with an abrasive sponge or spatula. Rinse the surface thoroughly. Repeat the procedure if necessary.
What to do if
Check out filasolutions.com to find the answer to any other questions you might have.
53
PROBLEM MATERIAL CATEGORY REFERENCE PRODUCTS ANSWER
Rust - Natural stone- Stoneware
and ceramics- Terracotta,
quarry tiles and brick
- Cement and tile joints
FILANO RUST,DETERDEk
Apply FILANO RUST, completely covering the stain. Leave to act for 15 minutes then remove any product residues and rinse. Alternatively (and in the event of very large stains), DETERDEk can be used. Dampen the area to be cleaned with water, then apply DETERDEk. Rub with a green abrasive sponge. Rinse thoroughly when finished. Avoid use on marble or limestone with fine polished surfaces.
Salt efflorescences
Terracotta, quarry tiles and bricks
DETERDEK,FILAPHzERO
To remove salt efflorescences, wash the surface with DETERDEk or FILAPHzERO diluted 1:5 and then rinse.
White alcohol, ammonia or bleach stains
- Terracotta, quarry tiles and bricks
- Natural stone
FILAPS87 Alcohol and ammonia, or products containing these substances whiten waxes. In this situation use FILAPS87 to strip the wax from the entire tile. Rinse with water and apply a coat of pure wax.
Residues of glue, chewing gum, adhesive tape and tree resin
- Terracotta, quarry tiles and bricks
- Porcelain and ceramic tiles
- Natural stone
FILASOLv, FILAPS87, FILAzERO SIL
Apply FILASOLv (undiluted) or FILAPS87 (diluted approx. 1:3 on surfaces previously dampened with water), and rub energetically with an abrasive green sponge. Rinse thoroughly when finished. Surface residues can also be removed using FILAzERO SIL: apply the undiluted product, covering the entire stain. Leave for 20 minutes and then use the spatula provided in the kit. Collect any residue with a soft cloth or kitchen towel. In the event of treated interior floors, the protective treatment should be restored after cleaning.
Wood FILASOLV, FILAzERO SIL Apply FILASOLv (undiluted) and rub with a sponge. Remove any residues when finished. Surface residues can also be removed using FILAzERO SIL: apply the undiluted product, covering the entire stain. Leave for 20 minutes and then use the spatula provided in the kit. Collect any residue with a soft cloth or kitchen towel. In the event of interior floors, any protective treatment should be restored after cleaning.
Residues of silicon and polyurethane foam
- Porcelain and ceramic tiles
- Natural stone- Glass- Metal, steel
FILAzERO SIL Apply FILAzERO SIL (undiluted), covering the entire stain. Leave for 20 minutes and then use the spatula provided in the kit. Collect any residue with a soft cloth or kitchen towel. In the event of interior floors, any protective treatment should be restored after cleaning.
NOTES
The smartphone and tablet app designed for building site professionals,
retailers and all those wanting to look after their home, is now available
in 6 languages: Italian, UK English, US English, German, Spanish and
French.
This application puts the best solution for any need on different materials
right at the fingertips of an increasing number of people: from care, to
washing after laying and protective treatment, to stain removal.
Available for all smartphones and tablets (both Apple and Android) and completely free of charge.
• TREATMENT SYSTEMSidentifies the ideal treatment for any surface (natural stone, porcelain tiles, terracotta, wood and other materials).
• TREATMENT STAGES identifies the suitable solutions for each stage during the treatment (pre-treatment, washing after laying, protection, finishing and maintenance).
• WHAT TO DO IF FAQs about common problems (stains, mould, application issues, etc.).
• PRODUCT CALCULATOR an additional function that will be popular with future users. It easily works out the amount of product needed for each treatment.
• FILA PRODUCT CATALOGUE contains detailed information about products, certification, treatment videos and technical information sheets.
• FIND YOUR NEAREST SALES POINT with an option for directions to your nearest store.
• TECHNICAL ASSISTANCE this puts the user in direct contact with Fila technical assistance, able to give a prompt reply to any advice required.
All Fila solutionsdirectly in your hands.
Member of:
Fila Industria Chimica S.p.a.Via Garibaldi, 5835018 San Martino di Lupari (Padova) - Italyt +39 049 9467300 f +39 049 9460753e info@filasolutions.com
Fila Chemicals USA, Corp.Miami, FL 33172t +1 305 513 0708e filausa@filasolutions.com
Fila Deutschland Vertriebs GmbHD-89312 Günzburg t +49 8221 2068314e filadeutschland@filasolutions.com
Fila España Industria Química S.L.12592 Chilches (Castellón)t +34 964.590101e filaespana@filasolutions.com filasolutions.com
FILAGROUP ∙ italia ∙ france ∙ united kingdom ∙ españa ∙ deutschland ∙ united states ∙ middle east
Fila France S.a.r.l.BP40026 - 69881 Meyzieu t +33 (0)4.72.46.01.74e filafrance@filasolutions.com
FILA Industria Chimica SpA Middle East BranchPO Box 309138 • Dubai, UAEt +971 44 542 642e filamiddleeast@filasolutions.com
Fila Surface Care Products LimitedSY8 9BR Ludlowt +44 1584 87 72 86e filauk@filasolutions.com
FILA products are sold by top flooring retailers and builder’s merchants.
stam
pato
da A
rti G
rafi
ch
e P
ost
um
ia -
FIL
AS
YS
TE
M_ U
K_re
v 0
5_ 0
2.1
6
Download APP FILA Solutions
top related