detail design flow of design information responsibility for “details” graphic communication...
Post on 21-Dec-2015
219 Views
Preview:
TRANSCRIPT
Detail design
Flow of design information Responsibility for “details” Graphic communication Written communication Oral presentations
Design Phase Information
Special Purpose Parts: Features Arrangements Relative dimensions Variable list Standard Parts: Type Variable list
ParametricDesign
ParametricDesign
Design variable valuese.g. Sizes, dimensions Materials Mfg. processesPerformance predictionsOverall satisfactionPrototype test results
DetailDesignDetailDesign
Product specificationsProduction drawingsPerformance Tests Bills of materials Mfg. specifications
Design information flow & decision-making
Sales&
Marketing
PurchasingProduction
EngineeringDesign
IndustrialDesign
IndustrialEngineering
ProductDevelopment
Team ManufacturingEngineering
in-class exercise
Sales & Marketing Responsibilities
Product WarrantyShippingWarehousingAdvertising campaignProduct literature Owner’s manual (layout, printing)Product launch
flow & decision-making
Industrial Design Responsibilities
Product trim detailsFinish detailsErgonomic refinements Product packaging
flow & decision-making
Design Engineering Responsibilities
Detail design performance analysesPreproduction prototype performance tests Manufacturing process specificationsOwner manual(s) (technical:operation/maint)Layout drawingDetail drawingsAssembly drawingsBills of materials Engineering change noticesPatents, trademarks, copyrights
flow & decision-making
Industrial Engineering Responsibilities
Materials & Product flow Facility layout/remodelingMaterial handling equipmentInventory warehousingAssembly planning (machines & workers)
flow & decision-making
Manufacturing Engineering Responsibilities
Fixture design / fabricationTool design / fabricationProcess equipment refurbishment/adaptationProcess equipment acquisition / installationProcess planning
flow & decision-making
Purchasing Responsibilities
Vendor qualification, selection, negotiationOut-sourcing parts or subassembliesRaw materials Materials planning Quality control (raw materials, sourced parts)Make or buy (shared)
flow & decision-making
Production
Tooling changeover (assist)Acceptance testing (QC, SPC)Worker trainingWorkforce scheduling
flow & decision-making
Quiz – Detail design info. responsibilities
Take out a sheet of blank paper Write the following headings on the left half Write two info. responsibilities for each on the right
half.
flow & decision-making
Name _________________
Team Member Responsibility
Sales & MarketingIndustrial DesignDesign EngineeringIndustrial EngineeringManufacturing EngineeringPurchasingProduction
Quiz – Detail design info. responsibilities
Take out a sheet of blank paper Write the following headings on the left half Write two info. responsibilities for each on the right
half.Name: A. Tovar
Team Member Responsibility
Sales & MarketingIndustrial DesignDesign EngineeringIndustrial EngineeringManufacturing EngineeringPurchasingProduction
Product launch, owner’s manual (layout)Finish details/ergonomics, packagingDrawings, BOM, owner’s manual (tech)Facility layout, assembly planning Tool design, process planningMaterials planning, quality control QC/SPC, Workforce training/scheduling
flow & decision-making
Communicating Design Information
Written and Oral CommunicationsEmailMemoranda / LettersPhone calls/voice mailsReports Meetings
What is the “secret” to goodcommunnication ?
Communicate to all the stakeholders: 1) often 2) thoroughly and 3) clearly.
Final design (not included in text)
Communication book: letters, emails, minutes, reports. Technical info book: catalogs, articles, surveys. Design book: sketches, diagrams, math models, optimization problems. Production drawing book: assembly drawings, detail drawings, list of standard and special-purpose parts or bill of materials.
Graphic Communications – Drawings
Production / Working drawings
•Detail drawing
•Assembly Drawing
•Bill of Materials (sometimes on Assembly)
•Layout (sketch)
dimensionline
extension line
dim’s between views
1.250
.500
1.000
2.000
.250.500
1.000
R.250
R.125
SCALE:1:1
SIZE DWG. NO.
AREV.
MATERIAL
FINISH
--
--
DO NOT SCALE DRAWINGAPPLICATION
USED ONNEXT ASSY
NAME DATE
SHEET 1 OF 1WEIGHT:
COMMENTS:
REVISIONS
DESCRIPTIONREV. DATE APPROVEDZONE
Q.A.
MFG APPR.
ENG APPR.
CHECKED
DRAWN RJE Engineering, Inc.
Support Bracket
0112345-001
4/5/03
space
0.875 countersink – 2 holes
mfg. process notes
revisions added heretitle block filled in
Detail Drawing Example
?
5?
?
4
1GR_ex ASSEMBLY
ITEM NO. QTY.PART NO. MATERIAL1 1guide SS 3032 1rod SS 3033 1PLATE SS 3034 2M8-1.25 x 30 ALUMINUM5 24mmcapscrew ALUMINUM
D
C
B
AA
B
C
D
12345678
8 7 6 5 4 3 2 1
THE INFORMATION CONTAINED IN THISDRAWING IS THE SOLE PROPERTY OF<INSERT COMPANY NAME HERE>. ANY REPRODUCTION IN PART OR AS A WHOLEWITHOUT THE WRITTEN PERMISSION OF<INSERT COMPANY NAME HERE> IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
NEXT ASSY USED ON
APPLICATION
DIMENSIONS ARE IN INCHESTOLERANCES:FRACTIONALANGULAR: MACH BEND TWO PLACE DECIMAL THREE PLACE DECIMAL
INTERPRET GEOMETRICTOLERANCING PER:
MATERIAL
FINISH
--
--
DRAWN
CHECKED
ENG APPR.
MFG APPR.
Q.A.
COMMENTS:
DATE NAME <COMPANY NAME>TITLE:
SIZE
BDWG. NO. REV
SHEET 1 OF 1WEIGHT:SCALE: 1:1
REVISIONS
REV. DESCRIPTION DATE APPROVEDZONE
UNLESS OTHERWISE SPECIFIED:
balloon annotations
Bill of MaterialsItem numberQuantityPart numberMaterial type or Source
Exploded view
Assembly Drawing Example
Engineering tolerances (ISO)
IT01, IT0, IT1, IT2, IT3, IT4, IT5, IT6.. Production of gauges and instruments.
IT 5, IT6, IT7, IT8, I9, IT10, IT11, IT12...Precision and general Industry.
IT11, IT14, IT15, IT16..Semi finished products IT16, IT17, IT18 ..Structural Engineering
http://www.roymech.co.uk/Useful_Tables/ISO_Tolerances/ISO_LIMITS.htm
Eingeering tolerances (English System)
RC: Running and sliding (Allowance >0, Max Clearance >0)
LC: Clearance and locational (Allowance =0, Max Clearance >0)
LT: Transition locational (Allowance <0, Max Clearance >0)
LN: Interference locational (Allowance <0, Max Clearance =0)
FN: Force and shrink (Allowance <0, Max Clearance <0)
Example (ISO)
Fit 6 H7/n6 Metric: Preferred Hole Basis (H) Allowance: -0.016 Max. Clearance: 0.004 Hole Limits: 6.012 / 6.000 Shaft Limits: 6.016 / 6.008 Hole Tolerance: 0.012 Shaft Tolerance: 0.008 Type of fit: Transition
Example (English System)
Fit 0.25 FN 1 English: Preferred Precision Fit, Hole Basis Allowance: -0.00075 Max. Clearance: -0.00010 Hole Limits: 0.25040 / 0.25000 Shaft Limits: 0.25075 / 0.25050 Hole Tolerance: 0.00040 Shaft Tolerance: 0.00025 Type of fit: Force
http://www.softpedia.com/user/licensing_nonfree.shtml
Example
Part A fits into part B All dimensions for part A are held 0.010 Specify the dimensions and tolerance for B
with an allowance of 0.010
Graphic Communications – Illustrations
• Charts - portray relationship(s) among numerical data, for example sales versus time.
• Diagrams - explain how something works or the relationship between the parts. E.g. free body diagrams to analyze static equilibrium forces and moments.
• Schematics - uses abstract symbols E.g. piping schematic, or electronics schematic.
• Figures - illustrates textual material
• Sketches - hand-drawn preliminary, or rough “drawings”, drawn without the use of drawing instruments.
Free Body Diagram
1r
Motor Pulley(driver)
2F
1F
1n T1yB
xB x
y
single body
coordinate axes
forces moments
geometry
other PDP’s
Gannt chart
Week 1 Week 2 Week 3 Week 4 Week 5 Week 6 Week 7 Week 8 Week 9Task 1/22-1/26 1/27-2/2 2/3-2/9 2/10-2/16 2/17-2/23 2/24-3/2 3/3-3/9 3/10-3/16 3/17-3/23Design Problem Formulation1.1 Site Visit1.5 Benchmarking1.6 Contact Customers1.7 Determine PDP/DV/SEP1.10 Outline Work Scope1.8 Determine Schedule1.9 Calculate Budget1.4 Create EDS1.3 Satisfaction Curves1.2 Complete QFD/HOQ1.11Report 1Conceptual Design 2.1,2,5,6,9 Generate Concepts2.7 Determine Physical Principles2.8 Conceptual Drawings2.3,4 Evaluate Concepts2.10 Report 2Configuration Design 3.1,2,10 Determine Configuration3.3 Determine General Dimensions3.5,6 Estimate Forces3.9 Analyze Lifting Performance3.8 Analyze Tire/Wheel Performance3.4 Outline Cost Analysis3.7 Config. Sketches
Written Design Communications
Letters / Email•Brief communications, often < a page in length•Sent to a few selected individuals •On a specific, usually familiar, topic•Email “letters” are informal in format and typically very
brief.
Memoranda•Longer than letter, from 3 to 9 pages, •Sent to a broader audience•Can cover more topics in greater depth than a letter. •Memoranda often emailed as attachments
Written Design Communications
Test Reports•Technical reports detailing engineering / scientific tests (on materials, prototypes and or products). •Can vary in length from few pages to hundreds of pages. •Contents include sections on: test objectives, test procedures, data/results, summary and recommendations.
Research reports•Similar to test reports•But longer in length and broader in coverage •Include additional sections such as: an abstract, background, literature review, laboratory/test program description and bibliography.
Owner manuals
•Include sections on: Setting-up / installing the product Operating the product Maintaining (i.e. clean, lubricate and adjust) Repair, if necessary.
•Can vary in length from 1 page to hundreds of pages
•Illustrations usually very important
Engineering change notices
•Brief descriptions of changes made to a product (I.e. what, why, how)•Detailed on a company-approved form•Authorized (signed) and distributed to all the critical depts.
Project Progress Reports
Sent to clients and other stakeholders, Covers project status re: workscope, schedule and
budget. Can vary in length from few to hundreds of pages Prepared weekly, monthly, quarterly, and annually
Design Reports
1. Introduction2. Design Problem Formulation3. Project Engineering4. Concept Design5. Configuration Design6. Parametric Design7. Prototype Tests8. Final Design9. Recommendations and Conclusions
(see figure 13.5 for more detail)
Patent, trademark and copyright information
Drawings, illustrations and textual materials are forms of “intellectual property.”
Represent investment of company funds, and as assests, they can be protected by law under:
patents trademarks or copyrights
Oral presentations
1) Plan (time, topics, temperament)
2) Outline
3) Compose
4) Rehearse
5) Refine
An excellent presentation requires excellent preparation
How can we prepare for an excellent presentation?
Plan
Decide on:who our audience will be,
what we wish to communicate, why we are giving the presentation,
and how long it should be.
Outline
Prepare a draft outline of the topics. If a group presentation, we need to agree upon responsibilities. Estimate the time to be devoted to each topic. Break up longer topics into smaller chunks.Combine or eliminate incidental topics. Discuss the draft outline with your co-workers. Confirm the draft outline with your immediate supervisor.
Compose
Use the outline to compose 3x5 (or 5x7) note cardsWrite clear and concise statements for major ideas and facts. Number each card in succession.Compose clear overhead slides/PowerPoint slides, use font > 20 ptPrepare videos using CAD animations or camcorder moviesPrepare posters, 35 mm slides, or working models, or demos.
Rehearse
Practice saying the note card phrases.Give our draft presentation to some friendly coworkers. Rehearse using the intended room and audio visual aids.Video tape and critically evaluate our delivery and visual aids.
Refine
Revise or re-write our note cardsEliminate confusing visual aids.Refine our visual aids.Revise presentation room layout or equipment
1. Make our listeners physically comfortable. Seating, lighting, room temperature, noise level and ventilation.
2. Expect & accept that we will be somewhat nervous. Convert nervousness to enthusiasm.
3. Take a deep breath and relax before beginning.
4. Start on time, stick to presentation schedule, and finish on time. Do not go over!
5. Pronounce clearly, sufficient volume, relaxed pace.
Execution Guidelines
6. Vary the pitch or tone of our voice occasionally
7. Add enthusiasm to our delivery.
8. Use visual aids judiciously (sparingly).
9. Use appropriate gestures and avoid annoying mannerisms.
10. Make frequent eye contact with our audience.
11. Use a pointer when appropriate.
12. Relax and “enjoy the ride.”
Execution Guidelines (continued)
top related