corning optical communications xwdm series brochure ......corning optical communications xwdm series...
Post on 01-Aug-2021
7 Views
Preview:
TRANSCRIPT
Connect to wavelength management
As consumers purchase more and more devices (cell phones, televisions, laptops, etc.) communication networks supporting these devices need to evolve to supply enough bandwidth for the increasing demand. One of the leading technologies allowing network operators to increase network density while leveraging current infrastructure is wavelength-division multiplexers (WDM). The WDM devices are placed within fiber optic hardware solutions which are typically located within the central office, headend, and the outside plant (OSP). As networks continue to evolve, WDM solutions become critical in maximizing the density and functionality required for modern optical distribution networks. You may ask, how do WDM solutions work? Similar to how prisms break out the visible light spectrum, WDM devices combine or break out wavelengths on a single fiber, enabling you to maximize fiber usage. A multiplexer (mux) combines these wavelengths over the fiber. A demultiplexer (demux) takes the combined wavelengths separating these into the individual signals. Therefore, a mux and demux are used to transmit and receive wavelengths between devices to exploit the full range of capabilites of the fiber within the network.
Corning Optical Communications xWDM Series Brochure | CRR-946-AEN | Page 1
WDM DeviceIndividual wavelengths, carrying different services and data, are either combined or separated with the use of a WDM, which has a series of thin-film filters inside (Photo 1).
The filters are tuned to allow specific bands of light (entered through the common port) to pass through (via the add/drop port) or be reflected off (via the reflect port) shown in Figure A. Individually tuned devices can be concatenated, creating a system that separates (demux) or combines (mux) multiple wavelengths one at a time, resulting in one signal separated into multiple frequencies, or multiple signals combined and carried over a single fiber (Figure B).
The WDM filters are placed into a device (CWDM and DWDM devices shown on next page). Dependent on the WDM type, the devices are then packaged in cassettes, modules, splice trays, etc. These different packages enable either splice or connectorized solutions.
Photo 1: Thin-Film Filter
COMMONADD/DROP
Adhesives and Filling Compounds
REFLECT
COMMONλ1+λ2+λ3+λ4
Rx1
Rx2
Rx3
Rx4
EXP/UPGAll Other Wavelengths
Passed Through
λ1
λ2
λ3
λ4
Figure A
Figure B
Corning Optical Communications xWDM Series Brochure | CRR-946-AEN | Page 2
Types of Wavelength-Division Multiplexers (WDMs)In order to accommodate differing needs for carrier networks, multiple types of WDMs have been developed, most prominently the coarse WDM (CWDM) and dense WDM (DWDM). As mentioned in the prior section, the filters are tuned to bands in order to distribute services to the proper locations. Each type of WDM device operates within a specific band. CWDMs are wider channel devices that are useful in short distance applications with fewer channel obligations. DWDMs have narrower channel widths, allowing for more capacity with higher electronics costs.
Coarse Wavelength Division Multiplexing (CWDM) ▄
CWDM devices function in any band (O-, E-, S-, C-, or L-band) between 1271 nm-1611 nm, with the S-, C-, and L-bands most commonly used▄
Channel spacing (defined by wavelength): - 20 nm spacing = 18 channels
CWDM Facts
CWDM Bands
Max Active Wavelengths per Fiber 18
Application Space-constrained environments
Distance Shorter distances and/or smaller channel counts
Wavelength Structure Spread far apart
Light Signal Not amplified
Active Electronic Cost $
Transport Capability Up to 18 channels from 1271 nm to 1611 nm with a 20 nm channel spacing
Spectrum Larger sections
Lasers Uncooled lasers due to wider channel spacings
1270
1290
1310
1330
1350
1370
1390
1410
1430
1450
1470
1490
1510
1530
1550
1570
1590
1610
O-Band1260-1360
3
2.5
2
1.5
1
0.5
0
E-Band1360-1460
Water peak
S-Band1460-1530
C-Band1530-1565
L-Band1565-1625
ITU-T G, 652 �ber
Legacy PON Architectures
Fibe
r At
tenu
atio
n (d
B/km
)
Typically not used dueto legacy water peakG/652.D �ber can beused (low water peak)
Most commonly usedwavelengths due tolower �ber attenuation
Corning Optical Communications xWDM Series Brochure | CRR-946-AEN | Page 3
Dense Wavelength-Division Multiplexing (DWDM)▄
DWDM devices are set to function in the C- and L-bands between 1531 nm-1611 nm▄
Channel spacing (defined by wavelength and frequency): - 200 GHz = 1.6 nm spacing = 40 channels - 100 GHz = 0.8 nm spacing = 80 channels - 50 GHz = 0.4 nm spacing = 160 channels
DWDM Facts
DWDM Bands
O-Band1280-1360
1270
1290
1310
1330
1350
1370
1390
1410
1430
1450
1470
1490
1510
1530
1550
1570
1590
1610
E-Band1360-1460
S-Band1460-1530
C-Band1530-1565
Most common usage in C-Band(40 DWDM channels 1530-1565 nm)
L-Band1565-1625
Corning Optical Communications xWDM Series Brochure | CRR-946-AEN | Page 4
Max Active Wavelengths per Fiber 160
Application High-density networks▄
No space constraints
Distance Long-haul and/or higher channel counts
Wavelength Structure Tightly packed
Light Signal Amplification may be used (EDFA; C-band)
Active Electronic Cost $$$ - laser performance
Transport Capability Up to 80 channels with 100 GHz spacing and up to 160 channels with 50 GHz spacing in the C-band through L-band spectrum
Spectrum Smaller sections
Lasers Cooled lasers due to tighter control of wavelengths
Optimizing FiberDue to the evolution of communication networks over the last 10 years, a major concern in today’s connected world is fiber exhaust, where the demands for fiber exceed the amount of available fiber in the network. WDM technology can alleviate fiber exhaust, by requiring fewer fibers to transmit and receive multiple services. Figure C demonstrates multiple signals transmitting over multiple fibers from one device to another. Figure D illustrates how multiplexing combines multiple channels at the transceiver device to transmit multiple signals over a single fiber. At the receiving device, a demultiplexer separates the signals. Overall, the use of WDMs allows you to take further advantage of your network, utilizing the untapped capacity of existing fiber, as well as the coexistence of multiple services across the same network.
Figure C
Figure D
Corning Optical Communications xWDM Series Brochure | CRR-946-AEN | Page 5
Voice Voice
Voice Voice
Data Data
Data Data
Storage Storage
Storage Storage
Voice Voice
Voice Voice
Voice Voice
Voice Voice
Data Data
Data Data
Storage Storage
Storage Storage
Voice Voice
Voice Voice
Mul
tiple
xor
Dem
ultip
lexe
r
WDM in Fiber Optic HardwareWhile WDMs work to optimize current fiber usage, when placed into fiber optic hardware, there are many configurations and functionalities that these devices can take on that determine the fiber requirements later in the network. Most commonly are dual or single functionality, where services and signals are sent over two fibers or one fiber respectively. A dual-function device has mux and demux capabilities over two fiber transmission (Figure D). A single function device has mux or demux capabilities over single-fiber transmission (Figure C).
Dual FunctionalitySeen in Figure E, dual functionality utilizes two fibers to transfer data to and from the end user. One fiber, at the top of Figure E, is used for downstream transfer while another fiber is devoted to upstream data. With this method, specific to this example, the same wavelength can be used for both directions of data traffic. From a hardware standpoint, Figure F shows that two common ports at different ends of the network are used for each direction of data traffic.
Single FunctionalitySeen in Figure G, single functionality transmits and receives all data in both directions on a single fiber. Due to the single-fiber use, now the downstream and upstream wavelengths must be different, to avoid interference during simultaneous transmission. Figure H illustrates an example of where the common ports are located on fiber optic hardware for single functionality. Instead of two common ports on each hardware device shown in Figure F, this figure only has one common port per hardware since it is leveraging one fiber instead of two.
COM
1470
1490
1510
1530
1550
1570
1590
1610
EXP
COM
1470
1490
1510
1530
1550
1570
1590
1610
EXP
COM
1470
1490
1510
1530
EXP
COM
1470
1490
1510
1530
EXP
COM
1470
1490
1510
1530
EXP
COM
1470
1490
1510
1530
EXP
Corning Optical Communications xWDM Series Brochure | CRR-946-AEN | Page 6
COMMON
λ1+λ2+λ3+λ4
Mux Demux
ISP OSP Field/Customer
Tx1
Tx2
Tx3
Tx4
EXP/UPG
λ1
λ2
λ3
λ4
Rx4
Rx3
Rx2
Rx1
EXP/UPG
λ1
λ2
λ3
λ4
COMMON
λ1+λ2+λ3+λ4
Demux Mux
Rx1
Rx2
Rx3
Rx4
EXP/UPG
λ1
λ2
λ3
λ4
Tx4
Tx3
Tx2
Tx1
EXP/UPG
λ1
λ2
λ3
λ4
COM
1470
1490
1510
1530
1550
1570
1590
1610
EXP
COM
1470
1490
1510
1530
1550
1570
1590
1610
EXP
COM
1470
1490
1510
1530
EXP
COM
1470
1490
1510
1530
EXP
COM
1470
1490
1510
1530
EXP
COM
1470
1490
1510
1530
EXP
Tx2
Rx2
Tx1
Rx1
EXP/UPG
λ4
λ3
λ2
λ1
COMMONλ1+λ3+λ5+λ7
λ2+λ4+λ6+λ8
Mux Demux
ISP OSP Field/Customer
Rx1
Rx1
Tx2
Rx2
EXP/UPG
λ1
λ2
λ3
λ4
Rx3
Rx3
Tx4
Rx4
λ5
λ6
λ7
λ8
Tx4
Rx4
Tx3
Rx3
λ8
λ7
λ6
λ5
Figure E Figure F
Figure G Figure H
Corning Optical Communications xWDM Series Brochure | CRR-946-AEN | Page 7
WDM ApplicationsService providers can leverage WDM technology in any part of their network including long-haul, metro, distribution, and access networks. As fiber demands in fiber to the home (FTTH), Cable TV (CATV), and long-haul networks increase with the rise of more connected technology, WDMs can fully utilize existing fiber by reducing the number of fibers required to transmit and receive signals. Because much of a network’s fiber constraints begin at the start of the network, WDM devices are frequently placed at the central office/headend, as demonstrated in the diagrams below.
FTTH Network
FTTH networks have relied on splitters and WDM devices for years. When evolving from a splitter-based PON to a next-generation PON technologies, more micro-optic devices are required for long-term future proofing of the network. These devices allow operators to reuse existing infrastructure while enabling more services to more customers.
CATV Hybrid Fiber COAX (HFC) Network
Transformation is occurring within HFC networks due to movement away from traditional RF cabling. CATV networks are currently capacity-constrained which poses concern for network designers and installers. As the headend and the OSP transition to new network architectures, designers and installers can replace traditional coax with high-density fiber optic cabling, cross-connects, and DWDM devices.
Long Haul
Legacy long-haul architectures have consistently leveraged WDM technology throughout their optical infrastructure. These technologies have provided cost savings and allow operators to service metropolitan, long-haul, and submarine networks.
NAP
DistributionFrameXWDMTX/RX
SpliceClosures
OSPCable
OSPCable Drop
VaultSplice
JumperJumperCO
NIDLCPSplitter
TX/RXM S L N
NAP
Home
DistributionFrameXWDM
CWDM
TX/RX
SpliceClosures
CATV NodeAssemblty
Business
OSPCable
OSPCable COAX
COAXDWDM
VaultSplice
JumperJumper
HE
TX/RXM
Jumper
M M
DWDM
Jumper
M
TAP
Home
TX/RX
TAP
Home
AMP
Child Node
CATV NodeAssembly
w/MTP
DistributionFrameXWDM EDFAEDFA EDFAEDFATX/RX Splice
Closures
PatchPanel
OSPCable
VaultSplice
JumperJumperCO
M
DistributionFrame XWDM TX/RX
VaultSplice
JumperJumper CO
M
JumperHut
# DCM#
##
EDFA EDFASpliceClosures
PatchPanel
OSPCable
SpliceClosures
OSPCable
JumperHut
# DCM#
##
Corning Optical Communications LLC • PO Box 489 • Hickory, NC 28603-0489 USA800-743-2675 • FAX: 828-325-5060 • International: +1-828-901-5000 • www.corning.com/opcommCorning Optical Communications reserves the right to improve, enhance, and modify the features and specifications of Corning Optical Communications products without prior notification. A complete listing of the trademarks of Corning Optical Communications is available at www.corning.com/opcomm/trademarks. All other trademarks are the properties of their respective owners. Corning Optical Communications is ISO 9001 certified. © 2019 Corning Optical Communications. All rights reserved. CRR-946-AEN / January 2019
Are you Corning connected?1-828-901-5000 (International)
800-743-2675 (United States and Canada)
ccsamericas@corning.com
www.corning.com/ISP
top related