chapter 20

Chapter 20

Roof Plan Components

2

Links for Chapter 20

Roof Plan Types

Roof Shape

Roof Materials

Related Web Sites

3

Roof Plan Types• Roof plan is used to show the shape of the

roof including roofing material, vent, and underlayment

• Size and direction of construction members are drawn

• Required for only complex roof designs

4

Roof Pitch• Slope or roof pitch is the description of the

angle of the roof as horizontal run and vertical rise

• Pitch is represented with a fraction which converts to an angle

5

Roof Shape• Flat Roof

– Economical– Built with slight pitch so water can run off– Parapet (false wall) is built around the roof

3 LAYER BUILT-UP ROOFING MATERIALHOT MOP BETWEEN EA. COURSE.

1/2" PLY ROOF SHEATHING

RAFTERS / CEIL. JST @ 12", 16" OR

10" BATT INSULATIONR-30 MIN W/ 2" AIRSPACE ABOVE

SOLID BLOCK W/(3)-1" DIA SCREENEDHOLES FOR AIR FLOW

SOLID BLOCKFASCIA

EXTRA PLATE TOPROVIDE SLOPE TO ROOF.

METAL GRAVEL STOP

6

Roof Shape• Shed Roof

– Less drainage problems compared to flat roof

– Can be built at any pitch

7

Roof Shape

• Gable Roof– Two shed roofs

meet at a ridge– Two or more

gables meet to form a hip or valley

8

Roof Shape• A-Frame Roof

– Rafters are used as supporting walls

– The structure appears to form the letter “A”

8 x 14 RIDGE BEAM

6 x 10 FLOOR

DECKING

6 x 12 EXPOSED BEAMS

1" ROOF DECKING

2 x 6 STUDS @ 16" O.C.3/4" FLOOR DECKING

2 x 10 FLOOR JOIST @ 16" O.C.

STANDARD 1 STORY 'T' FOOTING

CONCRETE FOOTING

@ 32" O.C.

BEAMS @ 32" O.C.

2" T.G. FLOOR

A-Frame Roof

9

10

Roof Shape• Gambrel Roof

– Traditional shape from colonial period

– Upper roof is greater pitch than lower roof

– Reduces cost of siding

11

Roof Shape• Hip Roof

– Eliminates roof mass– Structure appears

smaller– Two hips form a valley

12

Roof Shape

• Dutch Hip Roof– Combination of hip

and gable roof– Center is similar to

a gable roof– Ends are similar to

a hip roof

13

Roof Shape

• Mansard Roof– Similar to a

gambrel but angled lower roof is on all four sides

14

Roof Shape• Dormers

– Opening in a roof to allow for a window

– Used in gable or hip roof

15

Foundation & ½ Wall Section

Brick wall = 9” width( Total exterior wall)

Stucco= 4” ( total exterior wall width)

Block= 8” width ( exterior wall)

Roof SlopeFlat Roof: 2/12 Low Slope: 2/12-4/12 Conventional Slope Roof: 4/12-9/12 Steep Slope: 9/12 and higher

http://www.pole-barn.info/roof-pitch.html

Pitch= Rise/ Clear Span

Slope (pitch)= Rise : RunExample: 5:12Pitch = Rise

___________ Span= 5/24

Roof Pitchhttp://www.pole-barn.info/roof-pitch.html

Command: Line<45 & Dimension

Building Calculator.. Cool!!

25

Roofing Materials• Roof materials depend on the pitch, style,

structure cost, and weather• Squares are used to order roofing materials

– A square covers 100 sq. ft. of surface• Roofing materials also effect the framing

members and foundation

26

Built-up Roofing• Used with pitch below 3/12• Felt and asphalt is commonly use for flat or

low-sloped roof• Hot asphalt is spread between the layers of

roofing material

27

Shingles• Minimum pitch is 4/12 with 15-lb felt

underlayment• Made of wood, asphalt, or fiberglass• Most shingles are three-tab with a self-

sealing adhesive on the back• Wood shakes are thicker than shingles and

more irregular in shape

28

Clay and Cement Tiles• Used on expensive homes where the threat

of fire is extreme• Available in both curved and flat designs• Pitch is usually 2½/12 or greater• Roof will be much heavier with tiles

29

Metal Panels• Easy to install and therefore less expensive• Panels are made of 22- or 24-gage metal• Provide good water and fire protection• Available in widths of 18” or 24”• Variety of metals are available including

copper, stainless steel, aluminum and zinc

30

31

Related Web Sites• Asphalt Roofing Manufactures -

www.asphaltroofing.com• Cedar Shake & Shingle Bureau -

www.cedarbureau.org• Roofing Industry Educational Institute-

www.riei.com• Single Ply Roofing Institute- www.spri.com