capture board connection(eng)

DigiNet CAPTURE BOARD

CONNECTION

INDEX

1. KMC-4400R…………………………………………………………………………………3

2. KMC-9016 (R5)…………………………….…………………………………………12

3. KMC-8016D ………………………………….……………………………………………15

4. KIO-8816A …………………………………….……………………………………………19

5. I-AMP ………………………………………………………………………..……………….… 23

1) SPECIFICATION

•

•

•

•

•

•

1. KMC-4400R

2) FEATURE1~16CH VIDEO INPUT PORT

EXT. MONITOR OUTPUT (RCA)

1CH AUTOSELECT

1~4CH VIDEO INPUT PORT (BNC)

Reset JUMPER

Run , Power LED JUMPER

VIDEO BRIGHT CONTROL

1’ST CAM -----------à 16’TH CAM

FRONT Video, REAR GND

THIS MARK IS VIDEO

3) CONNECTION(4CH OVER)

3) CONNECTION(4CH OVER)

1’ST CAM -----------à 16’TH CAM

FRONT Video, REAR GND

THIS MARK IS VIDEO

1 – 4 CAM

5 – 8 CAM

9 – 12 CAM

13 – 16 CAM

GND

1’ST CAM VIDEO(1,5,9,13)

UPPER, LOWER SAME

2’ND CAM VIDEO(2,6,10,14)3’RD CAM VIDEO(3,7,11,15)

4’TH CAM VIDEO(4,8,12,16)

4) CONNECTION(8CH OVER)

Secondary CardPrimary Card

+

Primary Card Secondary Card4) CONNECTION(8CH OVER)

8CH

1’ST CAM 8’ST CAM 5’ST CAM 4’ST CAM

CPU

PrimarySecondaryPrimary card should be installed on the

slot near CPU however, it is subject to charge in some mainboards

16CH

4) CONNECTION(8CH OVER)

Secondary Card

1’ST CAM 8’ST CAM 5’ST CAM 4’ST CAM

Secondary Card

9’ST CAM 16’ST CAM 13’ST CAM 12’ST CAM

Primary Card

Primary Card

RESET + - (NO SEQ)

CONNECT TO THE MAIN BOARD’S RESET JUMPER

RUN LED LEFT +

POWER LED LEFT +

CONNECT TO THE MAIN BOARD’S HDD JUMPER

RUN LED RIGHT +

POWER LED RIGHT +

1) SPECIFICATION

• SAME AS OLDER KMC-9016

• OUTPUT 480 FRAME/SEC

• USE WITH KMC-4400R BOARD

• EXTERNAL MONITOR PORT

• COMPATIBLE DIGINET-3000 SYSTEM

2. KMC-9016(R5)

2) FEATUREA.FULL SCREEN BRIGHT ADJUST NOTICE. A : FIRST B : SECOND

NTSC/PAL NTSC : OPEN PAL : CLOSE

1~16CH VIDEO INPUT PORT

EXT. MONITOR OUTPUT (RCA)

DIVIDE SCREEN

B.DIVIDE SCREEN BRIGHT ADJUST

3) CONNECTION

16’TH CAM

FRONT Video, REAR GND

THIS MARK IS VIDEO

1’ST CAM

• UPGRADE KMC-7016D

• REPAIRED SCREEN VIBRATION

• 1CH TOTAL 30 FRAME/SEC

• 4 ~ 16CH TOTAL 25 FRAME/SEC

• NTSC/PAL VIDEO FORMAT

3. KMC-8016D

1) SPECIFICATION

1~4CH VIDEO INPUT(BNC)

1~16CH VIDEO INPUT

SCREEN BRIGHT ADJUST

Reset JUMPER

Run , Power LED JUMPER

AUDIO JUMPER

(USE LATER)EXT. MONITOR OUTPUT (RCA)

1CH AUTOSELECT

2) FEATURE

1’ST CAM -----------à 16’TH CAM

FRONT Video, REAR GND

THIS MARK IS VIDEO

3) CONNECTION

RESET JUMPER

RUN LED LEFT +

POWER LED LEFT + AUDIO (USE LATER)

• IO8816(ISA)’S UPGRADE• PCI SLOT TYPE• REMOTE CONTROL• NOTICE) WHEN USE THIS CARD, MUST BE SET CMOS BIOS SETUP’S

INTEGRATED PERIPHEARLS -> ONBOARD SERIAL PORT 1 : 3F8/IRQ4

4. KIO-8816A

KIO-8816A (PCI) IO-8816 (ISA)

1) SPECIFICATION

EXTERNAL MONITOR SENSOR INPUT,

CONTROL OUTPUTReset JUMPER

Run , Power LED

LED

REMOTE RX IR

P/T CONTROL RS422

COM PORT CONNECT PORT

2) FEATURE

EXT. MONITOR OUTPUT (RCA)

1CH AUTOSELECT

1’st CAM --à 16’th CAMFRONT Video, REAR GND

THIS MARK IS Video

RESET JUMPER

RUN LED LEFT +

POWER LED LEFT +

FRONT LEFT 1-8 SENSOR INPUT 9,10 GND

REAR LEFT 1-8 CONTROL OUTPUT 9,10 GND

3) CONNECTION

CONNECT TO COM1 PORT AT DVR’S REAR

CONNECT

UPPER RS422 +

LOWER RS422 -

CONNECT

5. I-AMP

This card use only DigiNet-3408, 3416 system

FRONT BACK

1) FEATURE

CONNECT TO PC POWER

2) CONNECTION